Database Users

[GUIDE] How to use Odin for GT-I9070

Odin is the saviour tool for all Samsung devices. The method for flashing by Odin differs from device to device.
This thread will give step by step instructions on how to flash a stock rom from Odin on the GT-I9070/p :
A. Download Odin tools from here : http://d-h.st/3zJ
Pass : shaaan
B. Download the stock rom from www.samfirmware.com
Setting up Odin :
1. Make sure you have installed the necessary drivers for this device. The drivers can be installed from within KIES or seperately. (I will upload the drivers shortly).
2. Run Odin as administrator.
3. Setting up the files is divided in two types depending on the firmware type :
a. If the firmware is a multi package file, put the files in the corresponding sections.
ie. CSC file in CSC section, PDA file in PDA section.
b. If the firmware is a single package, add the single file in the PDA section.
4. Now that Odin is setup, put the phone in download mode. To do that, power off the phone and press 'home+power+volume down' buttons together. Keep the buttons pressed till Download mide appears.
5. Now that Odin and the phone are setup, connect the phone to the device. Odin will detect the device and show something like 'com port (1)'
6. Flash the device.
7. The flash will take 5 minutes for a full flash on average.
8. When the flashing is complete, DO NOT remove the device until Odin shows ' PASS '.
9. The device will reboot. Remove the device, go to recovery mode and do a factory/data reset.
That's it. Happy flashing peeps..!!

Awesome guide mate - messing around with our device without Odin is risky !

This should be sticky. A lot of people is asking how to revert to original FW, or similiar questions that is connected to reverting. And it is almost at the end of forum, and thay cant see it.

I pmed the mods to do it. But they won't budge..
Please pm them..

Nice guide!!!
And adding images would be a nice option.
And plz add a point which tells which buttons to press like
"Re-Partition" ,"Auto Reboot","F.Reset Time" ,"Flash Lock"......
Sent from my GT-I9070 using xda premium

Very good guide,good work !
It may be better if you add some images

atishey23 said:
Nice guide!!!
And adding images would be a nice option.
And plz add a point which tells which buttons to press like
"Re-Partition" ,"Auto Reboot","F.Reset Time" ,"Flash Lock"......
Sent from my GT-I9070 using xda premium
Click to expand...
Click to collapse
From what I was able to find in other guides it is ONLY 'Auto Reboot' and 'F. Reset Time' to be checked.
All others to be unchecked.
There are some posts not to bother with that .pit file that is inside Odin .zip file.
Odin package from sammobile got 2 .pit files for 8GB - GT-I9070_EUR_XX_8G and GT-I9070_EUR_XX_8G_20111220_KL6 and one for 16GB
(at least paired with XEO region XXLD1) not only that one we got in link form 1st post.
I was also able to find some info that if you use .pit check also 'Re-Partition'.
Now I am curious about if It would be good idea for me to actually Re-Partition my phone - bought it used (not new) and my PC detects only 4GB of internal SD. Will it increase custom binary counter? (so far it is at 0 and I would rather keep it that way)
Is it going to fix that issue so I will be able to use all 8GB (minus system partition)?
If so how to use it and what .pit file to take?
.pit only, re-partition only and run it once, then single-package as PDA with reboot and F. Reset on another flash run?
Or maybe all at once?
BTW you guys ROCK.
Rooted SGS i9000 2 years ago with this forum and now I am very close to do it again with SGSA.

th3cr0w said:
From what I was able to find in other guides it is ONLY 'Auto Reboot' and 'F. Reset Time' to be checked.
All others to be unchecked.
There are some posts not to bother with that .pit file that is inside Odin .zip file.
Odin package from sammobile got 2 .pit files for 8GB - GT-I9070_EUR_XX_8G and GT-I9070_EUR_XX_8G_20111220_KL6 and one for 16GB
(at least paired with XEO region XXLD1) not only that one we got in link form 1st post.
I was also able to find some info that if you use .pit check also 'Re-Partition'.
Now I am curious about if It would be good idea for me to actually Re-Partition my phone - bought it used (not new) and my PC detects only 4GB of internal SD. Will it increase custom binary counter? (so far it is at 0 and I would rather keep it that way)
Is it going to fix that issue so I will be able to use all 8GB (minus system partition)?
If so how to use it and what .pit file to take?
.pit only, re-partition only and run it once, then single-package as PDA with reboot and F. Reset on another flash run?
Or maybe all at once?
BTW you guys ROCK.
Rooted SGS i9000 2 years ago with this forum and now I am very close to do it again with SGSA.
Click to expand...
Click to collapse
It is normal to have 4GB on internall SD. The rest of it goes to system partition, application partition and RAM I think...

shut_down said:
It is normal to have 4GB on internal SD. The rest of it goes to system partition, application partition and RAM I think...
Click to expand...
Click to collapse
googled a bit more and found it out too :crying:
BTW - both of those 8GB .pit files are identical (according to 'comp' tool in windows) so there is no reason to use re-partition - other than sth went totally wrong and you are trying to recover from brick or sth serious as this .pit file is already on your device.
Just flashed unbranded stock for XEO region - original one was branded.
NOTE to anyone who is still thinking about safety of this method:
After initial reboot - when it was reconfiguring in recovery mode - or however you will call it (just before odin should say 'pass' - still in that little font screen) windows started to reinstall usb drivers - odin log in bottom corner said 'disconnected' and even then my newly flashed ROM is working as it should. I would rather keep it connected till Odin confirms all went as intended but in case of similar issue - do not get heart attack

odin is used for flashing stock roms only???

Kulwinder Singh said:
odin is used for flashing stock roms only???
Click to expand...
Click to collapse
nope it can also be used to flash custom Roms and kernels though flashing custom kernels via odin will increase your bin counter !

Hello guys...
How are you? I´m new on the i9070 threads!!! I´ve had others phones before, like SG2, xperia sola, live with walkman... so, i need the password to descompress odin... i search on thread but i don´t found it...
SORRY I found the password... shaaan

Of what I understand, can I test an unlimited number of stock firmware and the binary counter remain 0?
If I flash an unbranded firmware can I use SIM cards from other providers?
Now my phone is branded and I can not use SIM cards from other providers.
Thanks.

Kulwinder Singh said:
odin is used for flashing stock roms only???
Click to expand...
Click to collapse
Read please, sir!
http://forum.xda-developers.com/showthread.php?t=1985199
:laugh:

Someone help me? LINK

Hi i have downloaded the russian jelly bean 4.1.2 package but when i tries to flash it using odin3 v1.83 it shows me "The Parameter is incorrect" why???

sonimayurp said:
Hi i have downloaded the russian jelly bean 4.1.2 package but when i tries to flash it using odin3 v1.83 it shows me "The Parameter is incorrect" why???
Click to expand...
Click to collapse
Try to remove .md5 from filename.

shut_down said:
Try to remove .md5 from filename.
Click to expand...
Click to collapse
Hmm it worked thx..

Flash JB
Hi, I want to flash Jelly Bean , do i need to use the pit file , or just select one package and then select the rom??
Edit : flashed

This version of Odin does not work when flashing JB to my device.
I successfully used Odin3v3.07 from this post: http://forum.xda-developers.com/showthread.php?t=2086965
Please update this guide. I spent quite a lot of time trying to figure out what was wrong.
Thanks

[GUIDE] [OFFICIAL ROM] [GT-N5100] 4.4.2 Kitkat Update!

Hello everyone, Im new here and this is my first thread. Please forgive me if I make mistakes. And sorry, I got no screenshots.
Did you ever wish you had Android KitKat on your GT-N5100? Well wish no more! The Official Update has already been released to Korea and Poland! It shouldn't take long for it to reach to other countries.
But if you are impatient, you can flash it now via Odin! ☺
Notes:
Make sure you have at least 80%
Make sure you have a back up
Make sure you remove ALL signs of root (e.g. Xposed,Busybox etc.)
Make sure all the apps in your External SD is moved to your Internal Storage. (To avoid force closing problems)
Make sure you have USB Debugging Enabled in Settings>Developer Options>USB Debugging
BEFORE THE PROCEDURE MAKE SURE YOU MAKE A BACK UP BECAUSE THIS CAN SOFT BRICK YOUR DEVICE.I AM NOT RESPONSIBLE FOR ANYTHING YOU DO WITH YOUR PHONE/TABLET/PHABLET
LETS BEGIN!!!
Download the Firmware from the Post below
After that unzip it and you will see 2 files, just put your attention to the tar.md5 files
Install Odin3 (Links below)
Now you need to install Samsung Kies. (Link also Below)
After installing kies go to the Odin3 Folder, Right click on it and hit "Run as Administrator"
Now that your done with the PC's Part. Put your attention on your tablet and shutdown/Power Off
After that press Volume Down and Home for a few seconds until you get into a screen with a Warning, just press Volume Up to continue.
And after that connect your phone to your PC via USB and Odin should automatically detect it.
An ID:COM[Number] will show in a box on the upper right and then click on PDA and go to the directory of where you put the unziped firmware folder you downloaded from SamMobile. Select the tar.md5 file.
After that make sure you dont have re-partition checked. Double check if you need to and hit "START"
PLEASE DONT REMOVE YOUR PHONE UNTIL YOU SEE A "PASS" MESSAGE IN THE BOX.
After that it should reboot and you now have Android 4.4.2 Kitkat on your GT-N5100!
Good Luck!
Incase you get in a Boot Loop
Press Volume Up and Power button to get into Recovery and perform a Factory Reset (Data wipe) then Wipe Cache Partition and Reboot.
Enjoy!
Source: International Business Times
Hit that thanks button if this helped!
LINKS ADDED! YEY!
ROOTING GUIDE COMING SOON
TROUBLESHOOTING
If your PC doesnt recognize your device, try reinstalling drivers, and if you are stuck on Download Mode just press and hold the Power Button until it shuts down then press and hold it again to turn your device on!
Tested on a Note 8! Didnt brick the device and is working, just make a backup incase you screw up.
Wanna see the changes? Go here

LINKS!
LINKS
Firmware
Kies (After updating make sure you use Kies3)
Odin3
Don't want to download Kies? Download these USB Drivers instead.
Enjoy!

ROOTING GUIDE IS NOW HERE
Click here to root you Samsung Galaxy Note 8!

John Shenon Uy said:
ROOTING GUIDE IS NOW HERE
Click here to root you Samsung Galaxy Note 8!
Click to expand...
Click to collapse
Quick and noob question.
I have Note N5100 stock, it is still on 4.1.2 firmware, now i want to flash with odin official 4.4.2 kitkat on it. (from above post)
So question is, do i need to root it first so i can flash 4.4.2?
Thank you.

CowboyWorld said:
Quick and noob question.
I have Note N5100 stock, it is still on 4.1.2 firmware, now i want to flash with odin official 4.4.2 kitkat on it. (from above post)
So question is, do i need to root it first so i can flash 4.4.2?
Thank you.
Click to expand...
Click to collapse
I would not flash official 4.4.2 kitkat with odin, over kies or over ota. You will get kitkat bootloader with knox, no write permissions for your apps to sd card, no working rooting method which would not trigger knox and void your warranty.
The rooting method he linked does not work for Exynos 4412 devices. Read the comments to the original geohots post in s5 forum or at least the towelroot thread in this section.

Yulka said:
I would not flash official 4.4.2 kitkat with odin, over kies or over ota. You will get kitkat bootloader with knox, no write permissions for your apps to sd card, no working rooting method which would not trigger knox and void your warranty.
The rooting method he linked does not work for Exynos 4412 devices. Read the comments to the original geohots post in s5 forum or at least the towelroot thread in this section.
Click to expand...
Click to collapse
Yeah it doesn't work, use CF-Auto-Root. Works perfectly,but you will see SuperSU Force closing or in some cases, it is not installed to fix this, install/update SuperSU
If and onlyif it doesn't work, try again.

John Shenon Uy said:
Yeah it doesn't work, use CF-Auto-Root. Works perfectly,but you will see SuperSU Force closing or in some cases, it is not installed to fix this, install/update SuperSU
If and onlyif it doesn't work, try again.
Click to expand...
Click to collapse
I have done update to 4.4.2 with odin and with out root.
And there is no waranty woid or knox trigger.
So everything was OK. But i have downloaded Poland version of 4.4.2 N5100XXDND8 from samsung updates page.

thank U

Sorry for the newbie question but how can I efficiently and completely backup my device? Any apps/software I can use? I know that I can just make a copy of all my photos, videos, etc to my laptop but how about my apps and its data? Will they be deleted after flashing this firmware?

I've got a problem here .
My simcard doesn't work .
It keep saying emergency calls only
Sent from my GT-I8262 using XDA Free mobile app

excuse me sir do you have a mirror of this firmware link like 4shared or mediafire?

would you please update download link of firmware? its expired
thanks

After I flashed my GT-N5100 with Samsung's official firmware, it keeps crashing apps everytime... Why??
PS: I can't install Ten Million (10000000) game as well somehow.
---------- Post added at 07:36 PM ---------- Previous post was at 07:32 PM ----------
imaniacsz said:
excuse me sir do you have a mirror of this firmware link like 4shared or mediafire?
Click to expand...
Click to collapse
Try the official Firmwares: http://www.sammobile.com/firmwares/database/GT-N5100/

Thanks

efs problematic after flashing firmware N5100
HI, its my first post on xda and new to this world so i will try to be reasonable here.
i followed the steps mentioned in this thread except one, i.e. i didnt make a backup. Now my n5100 wont move beyond initial samsung logo and the recovery mode says "cannot mount / efs"
i also found a thread which makes some excellent points (see below), but i would still like to know if any of you tried this and had a similar problem. if so, did you find a DIY method
http://forum.xda-developers.com/galaxy-s3/general/ref-imei-efs-stuff-i9300-including-t2393289

[Q] root for sm-t537v

First sorry if this has been asked the forum is rather large and sifting thru all the posts is a bit tedious. Is there a root out for the t537v module of the galaxy tab 4?
Thanks in advance

uroboch said:
First sorry if this has been asked the forum is rather large and sifting thru all the posts is a bit tedious.
Click to expand...
Click to collapse
Did you try towelroot?
Also don't keep saying what I quoted you on. Someone less nice than me is going to jump down your throat for it lol

thisisapoorusernamechoice said:
Did you try towelroot?
Also don't keep saying what I quoted you on. Someone less nice than me is going to jump down your throat for it lol
Click to expand...
Click to collapse
Thanks for the advice and yes i tried towel root it tells me "This Phone isn't Supported"

uroboch said:
First sorry if this has been asked the forum is rather large and sifting thru all the posts is a bit tedious. Is there a root out for the t537v module of the galaxy tab 4?
Thanks in advance
Click to expand...
Click to collapse
Hi ,
I think you have latest build now (4.4.4) , yes ? If yes , you must to try to flash via Odin older firmware http://www.sammobile.com/firmwares/download/34971/T537VVRU1ANE2_T537VVZW1ANE2_VZW/ from any source . Before flashing you must to do factory reset . Then to try Towelroot . Perhaps you must to try like here http://forum.xda-developers.com/showpost.php?p=58501194&postcount=245 . Then freeze or delete update service . If all will be fail , flash your last firmware again (for return back) .
Remember , you lost data when do factory reset .
You not afraid nothing .

repey6 said:
Hi ,
I think you have latest build now (4.4.4) , yes ? If yes , you must to try to flash via Odin older firmware http://www.sammobile.com/firmwares/download/34971/T537VVRU1ANE2_T537VVZW1ANE2_VZW/ from any source . Before flashing you must to do factory reset . Then to try Towelroot . Perhaps you must to try like here http://forum.xda-developers.com/showpost.php?p=58501194&postcount=245 . Then freeze or delete update service . If all will be fail , flash your last firmware again (for return back) .
Remember , you lost data when do factory reset .
You not afraid nothing .
Click to expand...
Click to collapse
Trying this now i will let you all know how it goes.

uroboch said:
Trying this now i will let you all know how it goes.
Click to expand...
Click to collapse
Sadly i couldn't get the old firmware to flash onto the device. if anyone has done this and had luck please let me know where you got the firmware and what you did to get it to work.
Thanks in advance.

uroboch said:
Sadly i couldn't get the old firmware to flash onto the device. if anyone has done this and had luck please let me know where you got the firmware and what you did to get it to work.
Thanks in advance.
Click to expand...
Click to collapse
Please wait little . I can to give you this firmware in the night .

Ready
UPD.Strangely, some problems with the archive. try to understand
Try this . May be you can to flash this tar-archive . If no , i will search new right archive .
See last post

I will try to fix it in afternoon

downloading the tar archive now i will let you know if i have success.
Thanks

uroboch said:
downloading the tar archive now i will let you know if i have success.
Thanks
Click to expand...
Click to collapse
https://www.androidfilehost.com/?fid=95916177934538217
All is OK !
Archive is good . My tab shows that archive is bad . And my PC shows that archive is normal .

repey6 said:
https://www.androidfilehost.com/?fid=95916177934538217
All is OK !
Archive is good . My tab shows that archive is bad . And my PC shows that archive is normal .
Click to expand...
Click to collapse
the message I'm getting is SW REV CHECK FAIL : [aboot]Fused 2 > binary 1

uroboch said:
the message I'm getting is SW REV CHECK FAIL : [aboot]Fused 2 > binary 1
Click to expand...
Click to collapse
you flash archive from https://www.androidfilehost.com/?fid=95916177934538217 ?

That's the archive I'm using. I don't think I'm using Odin right.

uroboch said:
That's the archive I'm using. I don't think I'm using Odin right.
Click to expand...
Click to collapse
Instructions
 Extract (unzip) the firmware file
 Download Odin v3.09
 Extract Odin ZIP file
 Open Odin v.3.09
 Reboot Phone in Download Mode (press and hold Home + Power + Volume Down buttons)
 Connect phone and wait until you get a blue sign in Odin
 Add the firmware file to AP / PDA
 Make sure re-partition is NOT ticked
 Click the start button, sit back and wait few minutes

uroboch said:
That's the archive I'm using. I don't think I'm using Odin right.
Click to expand...
Click to collapse
these are the directions I'm using to flash the device
http://primehowto.com/update-galaxy-tab-4-10-1-lte-verizon-sm-t537v-android-4-4-4-kitkat-t537vvru2ank1-official-firmware/
"How To Install T537VVRU2ANK1 Android 4.4.4 KitKat On Galaxy Tab 4 10.1 LTE (Verizon) SM-T537V Manually"
using the tar you gave me
Still getting above mentioned error on my device after i start the flash and it fails. Alas it appears i shall have to wait until someone figures out how to root the newest firmware.

uroboch said:
these are the directions I'm using to flash the device
http://primehowto.com/update-galaxy-tab-4-10-1-lte-verizon-sm-t537v-android-4-4-4-kitkat-t537vvru2ank1-official-firmware/
"How To Install T537VVRU2ANK1 Android 4.4.4 KitKat On Galaxy Tab 4 10.1 LTE (Verizon) SM-T537V Manually"
using the tar you gave me
Still getting above mentioned error on my device after i start the flash and it fails. Alas it appears i shall have to wait until someone figures out how to root the newest firmware.
Click to expand...
Click to collapse
So , good guide . Follow him . Unfortunately install this firmware does not work.
You dont try flash only older kernel like PDA via Odin ?

I also tried to flash using odin 3.07 and the PDA option but it fails.
Thanks again for all the help

uroboch said:
I also tried to flash using odin 3.07 and the PDA option but it fails.
Thanks again for all the help
Click to expand...
Click to collapse
Wait little i ask guru

repey6 said:
You dont try flash only older kernel like PDA via Odin ?
Click to expand...
Click to collapse
And why exactly shouldn't they try that? That's exactly what they're doing here I even contacted the moderator to verify that. Plus I used that method to re-root after I had to Odin back to complete factory stock. I don't see what the problem is flashing just an older kernel, rooting using towelroot, and then flashing the most current kernel. That's exactly how my tablet is rooted and was on the most current firmware (OA2) before I flashed Cyanogenmod

[Q] Confused about my specific device

Heya guys,
I've read through so many websites and forum posts but always when I think I have found the right thing for me, the model number, baseband version and/or build number varies...
All I want to do is root my phone. If there's a safe way to do this without tripping that KNOX whatever, that would be great but not even the most important to me.
And if it is possible I would also like to get Android 4.4.4 installed. Strangely, my phone says it is up to date (4.4.2) but I'm seeing people having 4.4.4 on theirs...
If there's something like a pack to get both, the update and the root, that would be mint!
Either way, I would be very thankful if someone could point me to a place where my exact device could get its appropriate files.
Model number: GT-I9301I
Baseband version: I9301IXXUANF2
Build number: KOT49H.I9301IXCUANJ4

you have the gt-i9301i so latest version for your device is 4.4.2 , but 4.4.4 is available for dual sim variant gt-i9300i you can root it i'll post the link below and navigate through the android devloppement section and find a rom that suits you then install it
link for root : http://forum.xda-developers.com/gal...overy-t-r-p-samsung-galaxy-s3-neo-gt-t2906840

Heya, thanks for the answer!
Ah, so there's also a dual sim variant. Mean that only they get the 4.4.4 update
So, on that link you gave me... do I need that stuff in the first post or is it enough for me to load and process the stuff in the second post (under 2nd Method I guess?)?

you choose which method you want to use then you're good to go

Yeah, but lets say I choose that "2nd Method ( Odin method )" - do I ALSO need that stuff from the first post (TWRP) or is that not needed then?

no just from 2nd post (odin mode)

Maximus0415 said:
no just from 2nd post (odin mode)
Click to expand...
Click to collapse
Wuaaah, when I go into download mode, it says "Product Name: GT-i9300i"
Now which one is right? O_O
Also, are you sure the second post stuff is all I need? It looks like all I'm getting there is a new recovery, it doesn't say anything about root...?

Ego_Bizarro said:
Wuaaah, when I go into download mode, it says "Product Name: GT-i9300i"
Now which one is right? O_O
Also, are you sure the second post stuff is all I need? It looks like all I'm getting there is a new recovery, it doesn't say anything about root...?
Click to expand...
Click to collapse
look dude download recovery.tar and the 2 zips supersu and knox removal then put them in your phone then put recovery.tar on odin then got to download mode on your phone then plug it to your computer then click start after it's done boot in recovery (lock key + home key + volume up key ) then flash the two zips and you're done mate

Maximus0415 said:
look dude download recovery.tar and the 2 zips supersu and knox removal then put them in your phone then put recovery.tar on odin then got to download mode on your phone then plug it to your computer then click start after it's done boot in recovery (lock key + home key + volume up key ) then flash the two zips and you're done mate
Click to expand...
Click to collapse
So I do need the two zips from the first post, you didn't say that before
I'm still confused, though, about the download mode telling me my device is a GT-i9300i. Is that just a bug or something?

Check about device

TotalErikas said:
Check about device
Click to expand...
Click to collapse
Yeah, there it says "GT-I9301I", that's why I'm confused. I don't know which is right.

Ego_Bizarro said:
Yeah, there it says "GT-I9301I", that's why I'm confused. I don't know which is right.
Click to expand...
Click to collapse
You have the i9301i then. Trust me.

Alright, thanks! I'll try this then... I hope there won't be any brickage O_O

Yay, everything worked as it should.
Since I applied the KNOX removal, is it also necessary to use TriangleAway?

Ego_Bizarro said:
Yay, everything worked as it should.
Since I applied the KNOX removal, is it also necessary to use TriangleAway?
Click to expand...
Click to collapse
No . I personally rooted my device with cf auto root. After I launched the SuperSU it removed KNOX

Hm, I think you misunderstood my question. KNOX seems to be removed already.
But there's still that other thing with the yellow triangle (years ago, one needed 'Triangle Away' to remove it), right? Or has Samsung given up on that when they introduced KNOX?

Ego_Bizarro said:
Hm, I think you misunderstood my question. KNOX seems to be removed already.
But there's still that other thing with the yellow triangle (years ago, one needed 'Triangle Away' to remove it), right? Or has Samsung given up on that when they introduced KNOX?
Click to expand...
Click to collapse
Yeah, considering I have never heard about it, it probably doesn't exist anymore.

[GUIDE] Download and install MM on SM-T715

Hi guys, i'm here to share with you the Android Marshmallow 6.0.1 firmware for the SM-T715 (wifi and LTE version). It's an italian version of the firmware but it should work with other regions too. Here's the link for the download:
Link: http://www.sammobile.com/firmwares/download/70887/T715XXU2BPD6_T715OXA2BPD6_ITV/
Courtesy of Sammobile.
And here's a guide (written by miguimercadob, all credits goes to him) that you can follow also for our tablet.
1->Turn off your tab and boot it into the Download Mode. To do this, turn off your device and then press and hold Volume Down + Home + Power buttons simultaneously for 2-3 seconds. When you see the warning screen with a yellow triangle sign, press the Volume Up/Down key to enter Download/Odin mode.
2->Download the required Odin.zip file and extract the file on your PC. You will get the Odin3_v3.10.7.exe file. Open it as the administrator to get to the Odin window.
3->Connect your Galaxy device to the computer using the USB cable.
4->When you connect the device, the ID: COM port on Odin will turn Blue. You’ll also see“Added!!” message to indicate successful connection. If Odin des not detect your tab, try to reinstall drivers, try another usb cable and another usb port.
5-> Check "AP" box and click on AP. A window will pop up, just go to the folder where you extracted the firmware and select T715XXU2BPD6_T715OXA2BPD6_ITV.tar.md5 file (name may vary according to device model)
6->Now Odin is checking MD5 and will freeze for a minute or so, but don't worry, just let Odin work.
7->Click on the "Options" section and make sure that only the Auto Reboot and F. Reset Time boxes are checked. (Do not, in any case, check Re-Partition box).
8->Now, click the Start button on Odin to begin firmware installation.
10->Once you get a PASS! message on Odin, your device will restart. It’s the green signal that indicates a successful installation.
11->Once our device restarts, you can disconect it.
12-> Enjoy Marshmallow on our Tab s2 (First boot will last for some minutes, just be patient! )
That's all! Hope that everyone can update
**HOW TO ROOT**
If you want to root your device, you can just follow this great GUIDE by miguimercadob
http://forum.xda-developers.com/tab-s2/general/sm-t710-6-0-1-t710xxu2cpd9-marshmallow-t3371545

Waiting root...

sarjarim said:
Waiting root...
Click to expand...
Click to collapse
I'n waiting for root too,,,but i only wanted to give an hand to other people who maybe don't care about it.

Hi! Would it work in T715y?

is 5g wifi working for anyone in North America? someone another thread had issues with UK MM update....

Root works with no issues. Just regular odin twrp and flash supersu.
Need to find how to enable theme engine/store and mm will be perfect

Jockard said:
Hi! Would it work in T715y?
Click to expand...
Click to collapse
I already tried flashing it but I keep on getting a fail in Odin
Sent from my SM-G935F using Tapatalk

jarayn said:
Root works with no issues. Just regular odin twrp and flash supersu.
Need to find how to enable theme engine/store and mm will be perfect
Click to expand...
Click to collapse
Which version do you install?
Link please.

Edgrr000 said:
I already tried flashing it but I keep on getting a fail in Odin
Sent from my SM-G935F using Tapatalk
Click to expand...
Click to collapse
I tried, and I get a fail too...

not work on T715Y

Jockard said:
I tried, and I get a fail too...
Click to expand...
Click to collapse
hehe....
it should at least work on the T715,
for us with the T715Y, we might still need to flash the MM bootloader and modem.
i'll try is anyways

Edgrr000 said:
hehe....
it should at least work on the T715,
for us with the T715Y, we might still need to flash the MM bootloader and modem.
i'll try is anyways
Click to expand...
Click to collapse
Alright so I'm stuck in a bootloop, I don't know how safe is to flash the T715 bootloader on the T715Y
Both tablet are the exact same....
Sent from my SM-G935F using Tapatalk

Can anyone provide a fast dl link. I'm dying to get the 715 FW downloaded.
finally got it to work:
Fast DL for SM-T715 6.0.1 FW from Samsung:
https://drive.google.com/open?id=0B84P5LHZlPQMWG1sNkxHSC1vWWc
Sent from my SM-T715 using Tapatalk

EBI_LANCER said:
not work on T715Y
Click to expand...
Click to collapse
Hi, this version is ONLY for SM-T715. On other variants, such as "SM-T715Y", "SM-T715C" or "SM-T715N0" will not work.

sarjarim said:
Which version do you install?
Link please.
Click to expand...
Click to collapse
Go to my post and you will find a link to downlad supersu as well as download instructions :POST
---------- Post added at 06:06 PM ---------- Previous post was at 06:02 PM ----------
Hi, Giuskiller, thanks for giving credits to me. Just one thing to say, people is asking for root, so it would be a good idea to add a link to my post so people can follow twrp and root instructions.

Ok to i stall this on uk 715?

Try flashing this CF autoroot via odin. Got mine here: https://autoroot.chainfire.eu/ with MD5 67eb614992217b1e188689ce116f2fb1

MM for SM T715 updates?
I currently have ee uk Android 5. So far only wifi tabs are officially rolling out MM. If I install this Italian version, and switch the language will I get any updates?

Giuskiller said:
Hi guys, i'm here to share with you the Android Marshmallow 6.0.1 firmware for the SM-T715 (wifi and LTE version). It's an italian version of the firmware but it should work with other regions too. Here's the link for the download:
Link: http://www.sammobile.com/firmwares/download/70887/T715XXU2BPD6_T715OXA2BPD6_ITV/
Courtesy of Sammobile.
And here's a guide (written by miguimercadob, all credits goes to him) that you can follow also for our tablet.
1->Turn off your tab and boot it into the Download Mode. To do this, turn off your device and then press and hold Volume Down + Home + Power buttons simultaneously for 2-3 seconds. When you see the warning screen with a yellow triangle sign, press the Volume Up/Down key to enter Download/Odin mode.
2->Download the required Odin.zip file and extract the file on your PC. You will get the Odin3_v3.10.7.exe file. Open it as the administrator to get to the Odin window.
3->Connect your Galaxy device to the computer using the USB cable.
4->When you connect the device, the ID: COM port on Odin will turn Blue. You’ll also see“Added!!” message to indicate successful connection. If Odin des not detect your tab, try to reinstall drivers, try another usb cable and another usb port.
5-> Check "AP" box and click on AP. A window will pop up, just go to the folder where you extracted the firmware and select T715XXU2BPD6_T715OXA2BPD6_ITV.tar.md5 file (name may vary according to device model)
6->Now Odin is checking MD5 and will freeze for a minute or so, but don't worry, just let Odin work.
7->Click on the "Options" section and make sure that only the Auto Reboot and F. Reset Time boxes are checked. (Do not, in any case, check Re-Partition box).
8->Now, click the Start button on Odin to begin firmware installation.
10->Once you get a PASS! message on Odin, your device will restart. It’s the green signal that indicates a successful installation.
11->Once our device restarts, you can disconect it.
12-> Enjoy Marshmallow on our Tab s2 (First boot will last for some minutes, just be patient! )
That's all! Hope that everyone can update
**HOW TO ROOT**
If you want to root your device, you can just follow this great GUIDE by miguimercadob
http://forum.xda-developers.com/tab-s2/general/sm-t710-6-0-1-t710xxu2cpd9-marshmallow-t3371545
Click to expand...
Click to collapse
does this effect your warranty or trip knox?
also is this suitable for LTE version?

riz157 said:
does this effect your warranty or trip knox?
also is this suitable for LTE version?
Click to expand...
Click to collapse
No this wont trip knox as you're just updating (at least my one is safe). And yes, my t-715 is LTE version, so no problems at all.