Hey guys,
finally i bricked my phone...
After a failed flash to TWRP recovery and a failed unbrick with fastboot, the phone won't start. Blackscreen. Only in device manager it show's "Qualcomm HS-USB QDLoader 9008". Is there any chance to unbrick or should i get a new mainboard?
PS: Sorry for my bad english, im from Germany
Thank you in advance
JaDa
@JaDaKiZz welcome to the party - read this http://www.reddit.com/r/lgg2/comments/2p5xei/the_lg_g2_is_unbrickable_a_story_of_death_and/ and let me know if you need any help. The MOST IMPORTANT thing you need to do is figure out the right KDZ for your phone.
Use http://csmg.lgmobile.com:9002/csmg/b2c/client/auth_model_check2.jsp?esn=xxxxxxxxxxxxxxx
replace xxxxxxxxxxxxxxx with your IMEI
Hey sandys,
the BoardDiag start but abort the test.
Linux don't show my G2 in devices. What can I do?
JaDa
Same thing happened to my phone. Thats what it shows in windows and isnt picked up by ubuntu. When I tried to use the lg tool to recovery it fails and says phone isnt in dload mode trying flash programmer. Dont have the money currently for @tungkick and dont see any other way.
How to Fix "error device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer. You need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
How to fix “No response from the device. Check PMIC first and
if still boot problem, replace AP.”
Remove battery and connect again put qualcomm 9008 then use tool in topic
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-all-variants/ Just as helping
[*]I see very topic unbrick qualcomm 9008 lg g2, lg g3 but all tool can not use.
I have full tool board ver 2.9.( only 2.9).
Link download drive.google.xxx /file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view?usp=sharing (xxx= com)
Support lg g2, lg g3 workking 100%.
Download tool, open BoardDiag and choose file tot correct model phone of you( you can download tot in xda)
See guide in pictrure : very easy.
Note
Hold power 2 minute and connect cable ( or remove battery)>>And open tool check ap, emmc test again
Then unbrick done remove cable, hold power 30 second and hold volume up connect cable phone put downloadmod >> Use lgflashtool 1.5 flash file tot again >> done.
If done pls donate a few beers paypal of my Thank you very much.
Man you saved my ass Thank you so much !1 when i get my salary ill donate to you and tell everybody to do so cuz this tool is amazing. im in download mode now ill try to flash with lg flash tool.
Thank so much man but my g3 last week unbrick qualcomm i had I submit for warranty[emoji24] [emoji24] I am very Star-crossed [emoji20]
Hello friend willcracker
Hello friend willcracker :good:
I hope all is well;
I saw this little tutorial so I want to ask for help
I have a LG G3 D855p and my phone is dead (bricked)
I can not quite understand the method you friend
not turn on my phone
I can not enter the "" Download Mode ""
VOL + Up when I connect the USB cable to the PC recognizes me as:
Qualcomm HS-USB QDLoader 9008 (COM10)
why I ask for help to revive my g3
If you help me ... .. I promise to donate something for you
you send a file "picture" attached
- - As I can get to "" Fastboot Mode "" on my phone
I hope your prompt response, please do not ignore my message :crying:
greetings from peru
You need to Disassemble Phone and Expose the TP Location
See pictrue
Expose the TP Location.
Done phone put qualcom 9008>> use tool unbrick
Remeber unplug battery connect only cable and short testpoint
Thanks for responding, but I need your help please friend
Hello willcracker I have no such tool you indicate "tool unbrick testpoint"
I could do this step with some type of cable or wire?
- If you Might tell me how to do that step with another option
leave your email. to chat google chat (Houngts) and you help me please
I'm worried because my g3 d855p not light, or anything like I said ....
await your prompt response, I hope you can help me
TOT Firmware, must match installed version?
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
Lollipop was installed, goal was to move to a custom rom (blisspop v2.3)
Rooting was successful
Install of twrp not, reboot into recovery caused the 'signature verification error'
Tried to flash the kitkat rom via the download method, failed, ...
Currently, I have the same verification error also when trying to get into download mode and have the Qualcomm HS-USB QDLoader 9008 in my device manager.
I have the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0.tot file and did the first step of your procedure. Can I do the second step with this extract of kitkat even if lollipop was installed?
any feedback greatly appreciated!
Hello willcracker thanks, thanks for reply but I need your help please
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
Greetings from Peru
Click to expand...
Click to collapse
NO you need find google how do short testpoint samsung n7100 you see they guide short testpoint . Lg when short testpoint phone detect qualcomm 9008
And you use tool board diag unbrick.
???
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
Click to expand...
Click to collapse
I'm in the same boat! Could you please explain it a little better?
frank.devliegher said:
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
any feedback greatly appreciated!
Click to expand...
Click to collapse
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Ahh now i see!
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
sourly64 said:
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
Click to expand...
Click to collapse
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
Model Lg d851? writh
rememer ber tool suppoer only lg g3 f400s/l/k , lg d855 16gb and 32gb.
If use tool say error pcmic on tool not support (Ex: lg d851)
I up load only msm8974ac g3 msm8975ac g3 no upload
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
It seems won't work.I have gone through about this problem.Alway AP Check fail.QPST reported that phone had been in Sahara download mode for few seconds.A RMA fix my phone.But it cost me about 50dollars
willcracker said:
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Click to expand...
Click to collapse
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
TOT Version
willcracker said:
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Click to expand...
Click to collapse
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
frank.devliegher said:
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
Click to expand...
Click to collapse
YES you can use tot kikat unbrick .
sourly64 said:
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
Click to expand...
Click to collapse
sr i have not upload hex lg gpro waitting comming soon.
Thank you for clicking my post, and taking an interest in either helping or contributing to a solution for my problem. Firstly flattery, I think what all you who contribute here do, is absolutely great! If I find a solution I will post it here for everyone else to benefit from. I'll make it quick...
Device: Samsung Note 4 SM-N910W8 (Canadian Version)
OS: Stock (unsure which version, was NOT rooted or anything)
Issue: Failed OS upgrade on Samsung Kies. Won't boot to download mode or recovery mode. No LED, No Charge Icon.
Log: Computer recognizes phone as QHSUSB_DLOAD or QHSUSB_BULK. Installed some qualcomm drivers NOW computer sees device as Qualcomm HS-USB QDLoader 9008 (COM 25). QPST and QFill recognize device in download mode. I would require step by step instructions of how to flash using these tools as my current knowledge of them is quite limited. From what I understand you can't JTAG the Note 4, but you can load a debrick image onto a 32/63GB microSD (that's based on my current research). So either using QFil or a microSD as a solution? I do have another note 4 (SM-N910W8) and although I don't want to...if it's my only choice and someone can provide me the steps/resources I can root it and use it to create a de-brick image (which I would then post here for the benefit of everyone). I think I can handle rooting it, but a link to guide would be appreciated (as I will want to unroot if after as well). Again I'de prefer if someone else with an already rooted SM-N910W8 could share a debrick image but I'll make one if I have to.
Your help is much appreciated. I'd be glad to provide a meager donation to whomever can provide a solution & resources.
Thanks,
TEXDASR
By any chance did you happen to get a N910W8 image? I am on Bell and am currently hard bricked looking around for one.
TEXDASR said:
Thank you for clicking my post, and taking an interest in either helping or contributing to a solution for my problem. Firstly flattery, I think what all you who contribute here do, is absolutely great! If I find a solution I will post it here for everyone else to benefit from. I'll make it quick...
Device: Samsung Note 4 SM-N910W8 (Canadian Version)
OS: Stock (unsure which version, was NOT rooted or anything)
Issue: Failed OS upgrade on Samsung Kies. Won't boot to download mode or recovery mode. No LED, No Charge Icon.
Log: Computer recognizes phone as QHSUSB_DLOAD or QHSUSB_BULK. Installed some qualcomm drivers NOW computer sees device as Qualcomm HS-USB QDLoader 9008 (COM 25). QPST and QFill recognize device in download mode. I would require step by step instructions of how to flash using these tools as my current knowledge of them is quite limited. From what I understand you can't JTAG the Note 4, but you can load a debrick image onto a 32/63GB microSD (that's based on my current research). So either using QFil or a microSD as a solution? I do have another note 4 (SM-N910W8) and although I don't want to...if it's my only choice and someone can provide me the steps/resources I can root it and use it to create a de-brick image (which I would then post here for the benefit of everyone). I think I can handle rooting it, but a link to guide would be appreciated (as I will want to unroot if after as well). Again I'de prefer if someone else with an already rooted SM-N910W8 could share a debrick image but I'll make one if I have to.
Your help is much appreciated. I'd be glad to provide a meager donation to whomever can provide a solution & resources.
Thanks,
TEXDASR
Click to expand...
Click to collapse
hi every one, i have SM G530w with FRP problem, then i managed to bypass it with method found in youtube.. but when i install update thru OTA in 100% phone restart then suddenly phone not powering on. itried to connet it with pc it was detected in Qualcomm HS-USB QDLoader 9008 .
i heard and found here solution only for other variants, i cant apply it yo my phone since my phone cant enter download mode.
please guide me to revive my phone, can someone create debricked image file for my phone SM G530w and share here, any help is much appreciated thank you.
azzir04 said:
hi every one, i have SM G530w with FRP problem, then i managed to bypass it with method found in youtube.. but when i install update thru OTA in 100% phone restart then suddenly phone not powering on. itried to connet it with pc it was detected in Qualcomm HS-USB QDLoader 9008 .
i heard and found here solution only for other variants, i cant apply it yo my phone since my phone cant enter download mode.
please guide me to revive my phone, can someone create debricked image file for my phone SM G530w and share here, any help is much appreciated thank you.
Click to expand...
Click to collapse
Post the problem in Q/A , help and troubleshooting
And ask moderatora to delete your post
Hey guys, I recently had an accident while trying to install stock firmware on my device. I tried to manually install a stock firmware ROM and in the middle of it the device just shut of. What I'm left with is a device which doesn't have fastboot or any other method of recovery other then through some qualcomm tools. The driver shows up as "qualcomm hs-usb qdloader 9008" on my computer. I tried following this guide https://www.droidsavvy.com/unbrick-qualcomm-mobiles/ and concluded that I'm stuck on the old hard brick and tried to follow the instructions but the problem here is that I don't think that I have the correct ROM file for QFIL because the firmware are zip files and not mbn as I think they are supposed to be. If anyone could help me with this in any way I'd really appreciate it, Thank you!
same as you man did you find a solution?
jesusloortega said:
same as you man did you find a solution?
Click to expand...
Click to collapse
https://forum.xda-developers.com/mo...766-unbrick-easy-sdcard-t3833408/post77427426