Database Users

Motorola XT1563 bricked

Motorola XT1563 Bricked
Hi guys, a Motorola XT1563 ( moto x play) was bricked. I try flash a original rom via rsd lite software and fastboot console cmd. No sucess because a bootloader is locked. I have make this steps in the support site oficial of Motorola for get the unike key and done. But... I try send comand fastboot oem unlock (code) when said:
...
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.004s
Well, this phone was bricked and don't boot... Why i check this setting if device didn't power on????
A biggest error of development i think.
Someone help me to find a solution?

Jhornands said:
Motorola XT1563 Bricked
Hi guys, a Motorola XT1563 ( moto x play) was bricked. I try flash a original rom via rsd lite software and fastboot console cmd. No sucess because a bootloader is locked. I have make this steps in the support site oficial of Motorola for get the unike key and done. But... I try send comand fastboot oem unlock (code) when said:
...
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.004s
Well, this phone was bricked and don't boot... Why i check this setting if device didn't power on????
A biggest error of development i think.
Someone help me to find a solution?
Click to expand...
Click to collapse
Can you boot into fastboot mode?
If yes...then boot into fastboot mode and reflash stock firmware using fadtboot commands

droider007 said:
Can you boot into fastboot mode?
If yes...then boot into fastboot mode and reflash stock firmware using fadtboot commands
Click to expand...
Click to collapse
For this i need unlock bootloader.
Example:
Device in fastboot mode
Conected in pc
Command in console cmd:
fastboot flash recovery recovery.img
Then
(Bootloader) preloader
FAILED (remote failure)
Errors..
I need help to unlock bootloader of device whitout check allow oem unlock in device because it no power on!!!

Check how to boot (not flash) to TWRP from fastboot. When you get into TWRP do a Factory Reset and reboot.

mausv said:
Check how to boot (not flash) to TWRP from fastboot. When you get into TWRP do a Factory Reset and reboot.
Click to expand...
Click to collapse
fastboot boot recovery.img

Jhornands said:
Motorola XT1563 Bricked
Hi guys, a Motorola XT1563 ( moto x play) was bricked. I try flash a original rom via rsd lite software and fastboot console cmd. No sucess because a bootloader is locked. I have make this steps in the support site oficial of Motorola for get the unike key and done. But... I try send comand fastboot oem unlock (code) when said:
...
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.004s
Well, this phone was bricked and don't boot... Why i check this setting if device didn't power on????
A biggest error of development i think.
Someone help me to find a solution?
Click to expand...
Click to collapse
same issue with me any solution for this.?
m not able to flash stock firmware it says
E:footer
E:signature failure
and when m unlocking boot loder it says oem unlock error

anujanuj said:
same issue with me any solution for this.?
m not able to flash stock firmware it says
E:footer
E:signature failure
and when m unlocking boot loder it says oem unlock error
Click to expand...
Click to collapse
someone found the solution:?

What error in bootloader log?
Enviado desde mi XT1563 mediante Tapatalk

Can you, at least, boot in stock recovery mode? If you can already boot in fastboot mode, you can use volume up and down keys to toggle between all the options, toggle it until you see "Recovery mode" and then push power button. Your phone will reboot in recovery mode and an option to do factory reset should be there. Stock recovery is less powerful than TWRP recovery but, it if you have a hard time installing TWRP, it could be another solution.

OTA possibly flashing, pushing the sd fastboot
Enviado desde mi XT1563 mediante Tapatalk

check this for enable
http://android.stackexchange.com/qu...ndroid-if-forgotten-pattern-for-screen-unlock

flopezm said:
check this for enable
http://android.stackexchange.com/qu...ndroid-if-forgotten-pattern-for-screen-unlock
Click to expand...
Click to collapse
what if phone shows internal and external memory not mounted

fix of hardbikd ....
here u go ...1st go fastboot mode n flash the stock file on fastboot mode the ...press power bottom 20 time fastly then u see warning bootloder logo the wait 5min after completing go 2 developsr allow oem ........

anujanuj said:
what if phone shows internal and external memory not mounted
Click to expand...
Click to collapse
Can you explain?
Sent from my XT1562 using Tapatalk

K.khiladi said:
Can you explain?
Sent from my XT1562 using Tapatalk
Click to expand...
Click to collapse
nothing this is too old post now my issue is solved

anujanuj said:
nothing this is too old post now my issue is solved
Click to expand...
Click to collapse
Mate your posts are everywhere on the forum.. ??
Sent from my XT1562 using Tapatalk

K.khiladi said:
Mate your posts are everywhere on the forum..
Sent from my XT1562 using Tapatalk
Click to expand...
Click to collapse
yes because my phone was dead and i had fade up

Jhornands said:
Motorola XT1563 Bricked
Hi guys, a Motorola XT1563 ( moto x play) was bricked. I try flash a original rom via rsd lite software and fastboot console cmd. No sucess because a bootloader is locked. I have make this steps in the support site oficial of Motorola for get the unike key and done. But... I try send comand fastboot oem unlock (code) when said:
...
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.004s
Well, this phone was bricked and don't boot... Why i check this setting if device didn't power on????
A biggest error of development i think.
Someone help me to find a solution?
Click to expand...
Click to collapse
Just get flash stock android 5.1.1 rom from fastboot if that doesn't work try getting into recovery mode and flashing the stock rom via adb sideload.

motorola x play ...stuck in boot
I am using a Motorola X Play 32 Gb Dual Sim phone with a Marshmallow 6.0.1
I'm now stuck at bootup with Start Up Failed.
Startup failed Error
your device didn't start up successfully
use the software repair assistant on computer
to repair ur device.
connect ur device to your computer to get
the software repair assistant
AP fastboot flash mode (Secure)
hab check failed for boot
Failed to verify hab image boot
failed to validate boot image
Error: failed to pass validation. backup to fastboot
Fastboot Reason: Fall-through from normal boot mode
pls Help by step by step methods I am Stuck.....Please

scorpionking3010 said:
I am using a Motorola X Play 32 Gb Dual Sim phone with a Marshmallow 6.0.1
I'm now stuck at bootup with Start Up Failed.
Startup failed Error
your device didn't start up successfully
use the software repair assistant on computer
to repair ur device.
connect ur device to your computer to get
the software repair assistant
AP fastboot flash mode (Secure)
hab check failed for boot
Failed to verify hab image boot
failed to validate boot image
Error: failed to pass validation. backup to fastboot
Fastboot Reason: Fall-through from normal boot mode
pls Help by step by step methods I am Stuck.....Please
Click to expand...
Click to collapse
same thing for me, been weeks cant find any solution

urgently Help! - Device boot looping, Can´t flash stock at all

Hello Everyone,
If anyone could help me, it would be highly appreciated.
Yesterday, I tried to update to the lastest Android 6.0 Version, my Moto X PLAY in Brazil.
I installed via Recovery, using the Official ZIP. When I did it, boot loop started.
I did factory erase, now it stills get boot looping, I can go to fastboot and recovery, but that'a all.
Tried to used RSD LITE, it dos not recognize my mobile, Device status are all " N/A"
Tried to use CMD via Fastboot, some of the commnads work, some of them fails.
Not sure of what I can do to solve this =confused:

Can you check thr twrp recovery in anothef post and flash it (restore recovery with the file)
Sent from my XT1562 using Tapatalk
---------- Post added at 05:18 PM ---------- Previous post was at 05:17 PM ----------
Did you click install supersu as last step. Skip the default supersu flash. It makes bootloop
Sent from my XT1562 using Tapatalk

Gopinath15 said:
Can you check thr twrp recovery in anothef post and flash it (restore recovery with the file)
Sent from my XT1562 using Tapatalk
---------- Post added at 05:18 PM ---------- Previous post was at 05:17 PM ----------
Did you click install supersu as last step. Skip the default supersu flash. It makes bootloop
Sent from my XT1562 using Tapatalk
Click to expand...
Click to collapse
but I do not have TWRP installed, and it is bricked, can I Install TWRP on it?

Heitor Amat said:
but I do not have TWRP installed, and it is bricked, can I Install TWRP on it?
Click to expand...
Click to collapse
unlock bootloader and flash rom again

bits9894 said:
unlock bootloader and flash rom again
Click to expand...
Click to collapse
But If I do this, will I be able to solve my problem ?

mine solved bro i unlocked bootloadernd flash cm 12.1 mine problem solved

bits9894 said:
mine solved bro i unlocked bootloadernd flash cm 12.1 mine problem solved
Click to expand...
Click to collapse
Problem is, can't unlock
C:\Users\heitor amat\Minimal Fastboot>fastboot devices
0017768 fastboot
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.012s

m facing same issue my phone is stuck on moto logo i have tried to downgrade but not successful now i have tried to unlock my boot loder it says
Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
but i can not allow this option from developer mode my phone is not starting any one can help me..?

anujanuj said:
m facing same issue my phone is stuck on moto logo i have tried to downgrade but not successful now i have tried to unlock my boot loder it says
Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
but i can not allow this option from developer mode my phone is not starting any one can help me..?
Click to expand...
Click to collapse
I am in the very same situation

Heitor Amat said:
I am in the very same situation
Click to expand...
Click to collapse
Try using this
http://forum.xda-developers.com/showthread.php?p=62922951
Sent from my XT1562 using Tapatalk

K.khiladi said:
Try using this
http://forum.xda-developers.com/showthread.php?p=62922951
Sent from my XT1562 using Tapatalk
Click to expand...
Click to collapse
sorry to say bro but not worked for me

K.khiladi said:
Try using this
http://forum.xda-developers.com/showthread.php?p=62922951
Sent from my XT1562 using Tapatalk
Click to expand...
Click to collapse
have not worked for me either

Try to flash latest firmware it will solve your problem

umair deshmukh said:
Try to flash latest firmware it will solve your problem
Click to expand...
Click to collapse
How do I do it?

Heitor Amat said:
How do I do it?
Click to expand...
Click to collapse
Download the latest firmware from here..http://www.filefactory.com/folder/dd05c058d3ff8dbe/?sort=created&order=DESC&show=100&page=1
Then flash it via fastboot..

Have you tried those two fastboot command yet?
fastboot format cache
fastboot format userdata
Click to expand...
Click to collapse
They are reported to help in similar case with Nexus phone and they are allowed even when the bootloader is locked. Flashing the original 5.1.1 kernel via fastboot should work too even with locked bootloader. This post describing how to downgrade to Lollipop should help since your troubles started after attempting to upgrade to Marshmallow: http://forum.xda-developers.com/moto-x-play/general/reminder-how-to-downgrade-6-0-to-5-1-1-t3267253. If error messages appear, maybe it's because you're using an older version of fastboot in Windows?
---------- Post added at 04:23 PM ---------- Previous post was at 04:05 PM ----------
Here's a zip file containing a working version of fastboot along with the setup file for the Motorola driver: https://drive.google.com/file/d/0B-OWWP0oC4yLVVRYSGRVcEFOd0U/view?usp=sharing

Got mine working!
I had the same problem, I was stock in the same bootloader screen.
The problem happened after flashing a firmware thru fastboot incorrectly (I was missing the las part of the system partition image #8). After you do this you cannot unlock the bootloader unless you have activated the OEM unlock option in Developer settings. If you didn't there is no way to unlock it.
I got my xt1563 dualsim back on by reflashing a compatible firmware. You can find the firmware here.
Mind the model and origin of your phone to select the correct firmware. If you select a different one fastboot will fail to flash it.
I ordered my moto x play on motorola.com I live in Mexico, because of that they sent a phone with a LATAM (latinamerican) firmware. I found this firmware, which then I flashed
Here is a guide on how to flash firmwares with fastboot.
Hope it Helps

the bootloader void

I've made some sort of mistake. I now have, what seems to be a bricked phone.
Phone was working fine but need to send it in. Want to unroot. FolIowed procedures via fastboot and had good success less the unlocked message.
I got careless but can't remember exactly what I did to get me to the state I'm in.
I can boot to bootloader (but nothing else) but all commands fail. If I perform 'fastboot devices', I get - ZY2235NZNF.
Beyond that, I get failures. first command - "fastboot oem lock begin"
(bootloader) Not supported command in current status!
FAILED (remote failure)
I was indeed able to boot to the phone and was only having the issue of the unlocked message. Now... I have the ~shame~
I have no Android so I cant get USB debugging... SO frustrated.
Thank you.
My goal here is to get my phone unrooted and back to stock rom.
Or, is it dead?
Thank you for reading my post and thank you in advance for any direction you can offer.

Flash it back to stock using rsdlite
Sent from my XT1562 using XDA-Developers mobile app

pijes said:
Flash it back to stock using rsdlite
Sent from my XT1562 using XDA-Developers mobile app
Click to expand...
Click to collapse
Filename: flashfile.xml
Creation Date: 01/05/2016 14:31:04
File size: 2558
Sofware Version: lux_reteu-user 6.0 MPD24.65-33 32 release-keysM8936_2020628.40.03.21.50R
For Phone Model: lux_reteu
FAIL
hab check failed for boot
Failed to verify hab image boot

flash twrp then try flashing any stock based ROM . once it's starts working...flash firmware using RSD lite. BTW you can't take the bootloader back to original state, you can relock it, in fastboot it'll show "relocked"
after flashing the ROM just use command
fastboot oem lock

Bellooch said:
I've made some sort of mistake. I now have, what seems to be a bricked phone.
Phone was working fine but need to send it in. Want to unroot. FolIowed procedures via fastboot and had good success less the unlocked message.
I got careless but can't remember exactly what I did to get me to the state I'm in.
I can boot to bootloader (but nothing else) but all commands fail. If I perform 'fastboot devices', I get - ZY2235NZNF.
Beyond that, I get failures. first command - "fastboot oem lock begin"
(bootloader) Not supported command in current status!
FAILED (remote failure)
I was indeed able to boot to the phone and was only having the issue of the unlocked message. Now... I have the ~shame~
I have no Android so I cant get USB debugging... SO frustrated.
Thank you.
My goal here is to get my phone unrooted and back to stock rom.
Or, is it dead?
Thank you for reading my post and thank you in advance for any direction you can offer.
Click to expand...
Click to collapse
did you try flashing TWRP?

sd_shadow said:
did you try flashing TWRP?
Click to expand...
Click to collapse
From the bootloader? VIA fastboot?
I tried teh WinDroid Toolkit, its not loading.
I don't know what else I'd do to add it.
I got bootloader, nothing else. No Android.

Bellooch said:
From the bootloader? VIA fastboot?
I tried teh WinDroid Toolkit, its not loading.
I don't know what else I'd do to add it.
I got bootloader, nothing else. No Android.
Click to expand...
Click to collapse
Yes with fastboot.

Lennyz1988 said:
Yes with fastboot.
Click to expand...
Click to collapse
Cool. How?
fastboot oem install twrp Lennyz1988...
I'm not sure of the command Lenny.

Bellooch said:
Cool. How?
fastboot oem install twrp Lennyz1988...
I'm not sure of the command Lenny.
Click to expand...
Click to collapse
you need to download a twrp.img and adb.exe files
fastboot flash recovery filename.img
fastboot reboot
Sent from my XT1080 using XDA Labs

sd_shadow said:
you need to download a twrp.img and adb.exe files
fastboot flash recovery filename.img
fastboot reboot
Sent from my XT1080 using XDA Labs
Click to expand...
Click to collapse
None of this works because the bootloader is locked.
Can't flash anything.
I tried everything. i got it to flash stock recovery. not that this did me any good. nothing else flashes. locked bootloader. can't unlock. won't flash anything until it is unlocked.
How do I unlock bootloader? I've tried fastboot method with key, no go. I've tried the motogogo (whatever) tool and no no.

Bellooch said:
None of this works because the bootloader is locked.
Can't flash anything.
I tried everything. i got it to flash stock recovery. not that this did me any good. nothing else flashes. locked bootloader. can't unlock. won't flash anything until it is unlocked.
How do I unlock bootloader? I've tried fastboot method with key, no go. I've tried the motogogo (whatever) tool and no no.
Click to expand...
Click to collapse
Download the firmware for your device here:
http://www.filefactory.com/folder/dd05c058d3ff8dbe/?sort=created&order=DESC&show=100&page=1
Then flash the files with fastboot using this thread.
http://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750
That should get your device up and running again.

Lennyz1988 said:
Download the firmware for your device here:
http://www.filefactory.com/folder/dd05c058d3ff8dbe/?sort=created&order=DESC&show=100&page=1
Then flash the files with fastboot using this thread.
http://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750
That should get your device up and running again.
Click to expand...
Click to collapse
did that. wouldn't flash. error. Grrrr. the problem is with OEM lock, it won't allow flash.

Bellooch said:
did that. wouldn't flash. error. Grrrr. the problem is with OEM lock, it won't allow flash.
Click to expand...
Click to collapse
What does it say on fastboot screen
complete text?
Sent from my XT1080 using XDA Labs
---------- Post added at 04:46 PM ---------- Previous post was at 04:45 PM ----------
or just post a screen shot
Sent from my XT1080 using XDA Labs

sd_shadow said:
What does it say on fastboot screen
complete text?
Sent from my XT1080 using XDA Labs
---------- Post added at 04:46 PM ---------- Previous post was at 04:45 PM ----------
or just post a screen shot
Sent from my XT1080 using XDA Labs
Click to expand...
Click to collapse
(bootloader) preflash validation failed
(FAILED) remote failure

Bellooch said:
(bootloader) preflash validation failed
(FAILED) remote failure
Click to expand...
Click to collapse
There should be more, version, date, battery status, usb status...

sd_shadow said:
There should be more, version, date, battery status, usb status...
Click to expand...
Click to collapse
Thank you. But, 'should be' doesn't help me.
What now? What other recommendations?

If our phone is bootloader unlocked, at the fastboot screen it will mention software status as Modified. looking at your fastboot screen, for me it looks more serious and I'm guessing it should be fine to just send the phone to the service center. perhaps a good idea to empty the battery as well so that the technician thinks it is completely dead

Bellooch said:
did that. wouldn't flash. error. Grrrr. the problem is with OEM lock, it won't allow flash.
Click to expand...
Click to collapse
What part wouldn't flash? Could you flash some parts or nothing at all?

Bellooch said:
(bootloader) preflash validation failed
(FAILED) remote failure
Click to expand...
Click to collapse
Recently I have this screen suddenly when I took my mxp from bag. I restore succesfully with RSDLite.

Lennyz1988 said:
What part wouldn't flash? Could you flash some parts or nothing at all?
Click to expand...
Click to collapse
Nothing at all.

Blasted kingroot - bricked my phone?

Ahh, hind sight is a wonderful thing.
After trying to use kingroot to get root access, it failed. And a few days later after rebooting.
I'm now stuck at bootup with Start Up Failed.
hab check failed for boot
Failed to verify hab image boot
failed to validate boot image
I've now tried lot's of different things, over the last few hours.
RSDLite (show device brings no thing up)
Unlock bootloader (request key, but error regarding OEM unlock not being set - no access to now set it LOL)
Downloaded stock X_Play_UK_Retail_XT1562_LPD23.118-10_CFC.xml.zip, and tried using various guides on fastboot but keep getting remote failed.
I'm on stock recovery (obviously still locked).
Any thoughts, or hope from anyone?
Obviously, not sure what support Motorola would provide for what is essentially my own fault?

Have you tried manually flashing each bit of the stock firmware/image. That might help. There's a good guide here which I followed to unbrick my device. Just follow the instructions http://theunlockr.com/2015/09/22/how-to-unroot-the-motorola-moto-x-play/

Or try this one.
http://forum.xda-developers.com/showthread.php?t=2499926

Tried the first fastboot oem lock begin but get ... (althought my phone is locked already)
(bootloader) Not supported command in current status!
FAILED (remote failure)
finished. total time: 0.063s
So stepping to next command, I get:
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot flash partition gpt.bin
(bootloader) has-slotartition: not found
target reported max download size of 268435456 bytes
sending 'partition' (32 KB)...
OKAY [ 0.166s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 1.078s

sharebubbles said:
Tried the first fastboot oem lock begin but get ... (althought my phone is locked already)
(bootloader) Not supported command in current status!
FAILED (remote failure)
finished. total time: 0.063s
So stepping to next command, I get:
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot flash partition gpt.bin
(bootloader) has-slotartition: not found
target reported max download size of 268435456 bytes
sending 'partition' (32 KB)...
OKAY [ 0.166s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 1.078s
Click to expand...
Click to collapse
I think you need to unlock the bootloader and then start with the 'fastboot oem lock begin' command. You can't flash a system image with a locked bootloader. Let me know how it goes!

DTLblaze said:
I think you need to unlock the bootloader and then start with the 'fastboot oem lock begin' command. You can't flash a system image with a locked bootloader. Let me know how it goes!
Click to expand...
Click to collapse
I run the unlock command, with my unique key but I get ..
...
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.013s
And since I can't get into the phone, I can't therefore check the "allow OEM unclock"

Have you tried any erase data commands or reset commands? Perhaps you could reset the phone so kingroot is un-installed and then try to turn on the phone. Short of that I'm stuck for ideas really, accept booting into 'fastboot and then erasing all data and factory reset in there. Let me know.

DTLblaze said:
Have you tried any erase data commands or reset commands? Perhaps you could reset the phone so kingroot is un-installed and then try to turn on the phone. Short of that I'm stuck for ideas really, accept booting into 'fastboot and then erasing all data and factory reset in there. Let me know.
Click to expand...
Click to collapse
I tried the wipe data/factory reset and wipe cache partition from the stock recovery.
And if I try from fastboot:-
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot erase userdata
(bootloader) has-slot:userdata: not found
erasing 'userdata'...
OKAY [ 0.196s]
finished. total time: 0.198s
And then a fastboot reboot.
Back to the now standard "start up failed"
And the
AP Fastboot Flash Mode (Secure)
hab check failed for boot
Failed to verify hab image boot
failed to validate boot image
ERROR: Failed to pass validation, backup to fastboot
Fastboot reason: Fall-through from normal boot mode

Sickaxis79 said:
Or try this one.
http://forum.xda-developers.com/showthread.php?t=2499926
Click to expand...
Click to collapse
Have downloaded, and tried that - but the crux appears to be the fact that my bootloader is locked and I can't access the OEM checkbox. And therefore the tool itself can't unlock or equally install TWRP.
Unless I'm missing something in it's usage.

sharebubbles said:
I tried the wipe data/factory reset and wipe cache partition from the stock recovery.
And if I try from fastboot:-
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot erase userdata
(bootloader) has-slot:userdata: not found
erasing 'userdata'...
OKAY [ 0.196s]
finished. total time: 0.198s
And then a fastboot reboot.
Back to the now standard "start up failed"
And the
AP Fastboot Flash Mode (Secure)
hab check failed for boot
Failed to verify hab image boot
failed to validate boot image
ERROR: Failed to pass validation, backup to fastboot
Fastboot reason: Fall-through from normal boot mode
Click to expand...
Click to collapse
That really does sound like you bricked the device. If you where on lollipop software you wouldn't have the issue with check bootloader OEM unlock. If it was me I would either contact Motorola or go to a repair shop and have a motd experienced person take a look at it.

Try this, not necessary for unlock bootloader
Recognized Contributor3,144 posts Thanks: 1,591
Quote:
Originally Posted by sheikh.sami17
but i have locked bootloader. can i flash stock firmware with locked bootloader?
YES you can flash stock Moto roms meant for your model and carrier only.
Also, Never attempt to downgrade.
In this page
http://forum.xda-developers.com/moto-x/moto-x-qa/q-how-to-flash-to-stock-firmware-t3041813
I edit and made one firmware autoflasher for my x play Indian version and flashed successfully . everybody should check sparsechunk files no in flash file of your extracted stock firmware and edit my autoflasher files according to number of sparsechunk files and flash your firmware. It is definitely safe and I flashed my firmware by this but use at your own risk .
https://mega.nz/#!aoETEL7b!6WUe8tXeh...HHohpfYf2duoLc
First you have to download your phone's correct firmware and extract in fastboot folder , and add my autoflasher and check your sparsechunk files number and make changes according to that in autoflasher then save ..Enter your phone in fastboot mode or in bootloader and not in stock recovery and run autoflasher.
IF YOU HAVE ANY DOUBT AT TAKING RISK , CONTACT Motorola AND MAKE EVERYTHING EASY.

sharebubbles said:
Have downloaded, and tried that - but the crux appears to be the fact that my bootloader is locked and I can't access the OEM checkbox. And therefore the tool itself can't unlock or equally install TWRP.
Unless I'm missing something in it's usage.
Click to expand...
Click to collapse
Strange. This is the tool I used to unlock my bootloader.

drmuruga said:
Try this, not necessary for unlock bootloader
Recognized Contributor3,144 posts Thanks: 1,591
Quote:
Originally Posted by sheikh.sami17
but i have locked bootloader. can i flash stock firmware with locked bootloader?
YES you can flash stock Moto roms meant for your model and carrier only.
Also, Never attempt to downgrade.
In this page
http://forum.xda-developers.com/moto-x/moto-x-qa/q-how-to-flash-to-stock-firmware-t3041813
I edit and made one firmware autoflasher for my x play Indian version and flashed successfully . everybody should check sparsechunk files no in flash file of your extracted stock firmware and edit my autoflasher files according to number of sparsechunk files and flash your firmware. It is definitely safe and I flashed my firmware by this but use at your own risk .
https://mega.nz/#!aoETEL7b!6WUe8tXeh...HHohpfYf2duoLc
First you have to download your phone's correct firmware and extract in fastboot folder , and add my autoflasher and check your sparsechunk files number and make changes according to that in autoflasher then save ..Enter your phone in fastboot mode or in bootloader and not in stock recovery and run autoflasher.
IF YOU HAVE ANY DOUBT AT TAKING RISK , CONTACT Motorola AND MAKE EVERYTHING EASY.
Click to expand...
Click to collapse
I've ben used the latest rom so far why trying to flash (and failing) when I look at recovery I have a LPD23.118-10 number that matches to an earlier 5.1.1 rom (I had been upgraded to 6.0.1 via OTA updates) - do I therefore take that LPD ID to mean that I should actually use the 5.1.1 rom - I'm in the UK, so I'm assuming I'd use the UK one rather than Europe (I'm looking at roms on https://github.com/motoxplay/stock).
Thanks

Dooh!!
Looking back at what I was doing yesterday, within the mix of downloading various roms - appears that I was actually using the LPD23.118-10 and NOT the latest.
I figured, I'd give it one last whirl using the latest not expecting much - and hey presto, it's worked. Just in the process of resetting it all up again.
Thanks for everyone who contributed, and a lesson learnt about always rechecking what you attempt (and not to try to root if you're not 100% sure of what I'm doing)

sharebubbles said:
Dooh!!
Looking back at what I was doing yesterday, within the mix of downloading various roms - appears that I was actually using the LPD23.118-10 and NOT the latest.
I figured, I'd give it one last whirl using the latest not expecting much - and hey presto, it's worked. Just in the process of resetting it all up again.
Thanks for everyone who contributed, and a lesson learnt about always rechecking what you attempt (and not to try to root if you're not 100% sure of what I'm doing)
Click to expand...
Click to collapse
And also never try kingroot.

sharebubbles said:
Dooh!!
Looking back at what I was doing yesterday, within the mix of downloading various roms - appears that I was actually using the LPD23.118-10 and NOT the latest.
I figured, I'd give it one last whirl using the latest not expecting much - and hey presto, it's worked. Just in the process of resetting it all up again.
Thanks for everyone who contributed, and a lesson learnt about always rechecking what you attempt (and not to try to root if you're not 100% sure of what I'm doing)
Click to expand...
Click to collapse
Most in the threads suggesting using rsdlite or manual flash/root and you decided to use kingroot,haha.
Welcome back.

Guys I have been searching EVERYWHERE on how to unbrick my moto x play, I used kingroot and it bricked, been a week and I TRIED everything. CAN ANYONE HELP PLEASE!!!!!!
---------- Post added at 05:26 AM ---------- Previous post was at 05:14 AM ----------
Guys I have been searching EVERYWHERE on how to unbrick my moto x play, I used kingroot and it bricked, been a week and I TRIED everything. CAN ANYONE HELP PLEASE!!!!!!
Tried restoring it, deleted everything and the phone is still on bootloader (LOCKED) and i dont even know how to fix it, I know nothing on how to root, friend suggested it, downloaded it, installed it, didnt work and then i restarted my phone and now its stuck on bootloader screen and the screen has the message "Start up failed: your device didnt start up successfully. Use the software repair assisstant on computer to repair your device. Connect your device to your computer to get the Software Repair Assistant." <- Downloaded it, tried it and it was stuck on 6% on repairing, left it over night and it was still on 6%.
ALSO under the message "AP Fastboot Flash Mode(Secure) is there)

Hai same problem for my moto x play ple.......s help contact.7708892303(WhatsApp no.)

pravin kkr said:
Hai same problem for my moto x play ple.......s help contact.7708892303(WhatsApp no.)
Click to expand...
Click to collapse
Download and flash this firmware
https://mega.nz/#!H5YlDCrD!T8tAAW7nHVS-erizRiqg5-Yp_p23hKParMjjHD4diQA credits @kumeipark
Use RSD lite to flash the firmware
http://rsdlite.com/rsd-lite-download/
Moto drivers
http://motorola-mobility-en-in.custhelp.com/app/answers/detail/a_id/88481
If you have problems installing device drivers using Windows 8.1 or Windows 10 follow this guide
https://www.youtube.com/watch?v=gmw86KplqmU
And don't post your contact no. in public forums for everyone to see.

what is the decryption key for the mega link
drmuruga said:
Try this, not necessary for unlock bootloader
Recognized Contributor3,144 posts Thanks: 1,591
Quote:
Originally Posted by sheikh.sami17
but i have locked bootloader. can i flash stock firmware with locked bootloader?
YES you can flash stock Moto roms meant for your model and carrier only.
Also, Never attempt to downgrade.
In this page
http://forum.xda-developers.com/moto-x/moto-x-qa/q-how-to-flash-to-stock-firmware-t3041813
I edit and made one firmware autoflasher for my x play Indian version and flashed successfully . everybody should check sparsechunk files no in flash file of your extracted stock firmware and edit my autoflasher files according to number of sparsechunk files and flash your firmware. It is definitely safe and I flashed my firmware by this but use at your own risk .
https://mega.nz/#!aoETEL7b!6WUe8tXeh...HHohpfYf2duoLc
First you have to download your phone's correct firmware and extract in fastboot folder , and add my autoflasher and check your sparsechunk files number and make changes according to that in autoflasher then save ..Enter your phone in fastboot mode or in bootloader and not in stock recovery and run autoflasher.
IF YOU HAVE ANY DOUBT AT TAKING RISK , CONTACT Motorola AND MAKE EVERYTHING EASY.
Click to expand...
Click to collapse
provide the decryption key

Phone Stuck | Need to recover photos from internal memory

Hi All,
Due to in ternal memory full, suddenly my home button stopped working and notifications were not appearing. I tried and followed advice written in one of the websites:
"f you didn't enabled developer settings and usb debug prior to the defect, you can create an icon to call this Activity using Nova Launcher.
After installing it and launching, long press home screen, select widgets, swipe right to find Activity icon, place on empty space in your home, search for setup wizard (it changes accordingly to your native language), select .SetupWizardTestActivity and voilá."
But, now my phone is stuck in SetupWizardTestActivity loop. I desperately need to recover my photos and other data on internal memory.
Please suggest.
Additional Info:
Using Moto X play (updated to Marshmallow)
Bootloader is unlocked

Can't you just boot into safe mode and try if that works.
Boot into Safe Mode
With the phone on, press and hold the power key until the on-screen “Power off” option shows up.
Long press on the on-screen button, and select “Boot into Safe Mode.”
or if you have an unlocked bootloader you can flash TWRP and use the build in file manager to transfer the files to your sd.

anujagraj said:
Hi All,
Due to in ternal memory full, suddenly my home button stopped working and notifications were not appearing. I tried and followed advice written in one of the websites:
"f you didn't enabled developer settings and usb debug prior to the defect, you can create an icon to call this Activity using Nova Launcher.
After installing it and launching, long press home screen, select widgets, swipe right to find Activity icon, place on empty space in your home, search for setup wizard (it changes accordingly to your native language), select .SetupWizardTestActivity and voilá."
But, now my phone is stuck in SetupWizardTestActivity loop. I desperately need to recover my photos and other data on internal memory.
Please suggest.
Additional Info:
Using Moto X play (updated to Marshmallow)
Bootloader is unlocked
Click to expand...
Click to collapse
If bootloader is unlocked then recovering data is easy, I guess you have TWRP recovery if not flash twrp then pop in a sd-card boot into recovery and copy everything to the card. Done.
Edit: the above comment says the same thing, I had not noticed that .

While flashing TWRP recovery, I am getting the following message in CMD:
target reported max download size of 268435456 bytes
sending 'recovery' (8362 KB)...
OKAY [ 0.276s]
writing 'recovery'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.310s
In phone's bootloader logs, I can see: "Mismatched partition size (recovery).
Please help!

Lennyz1988 said:
Can't you just boot into safe mode and try if that works.
Boot into Safe Mode
With the phone on, press and hold the power key until the on-screen “Power off” option shows up.
Long press on the on-screen button, and select “Boot into Safe Mode.”
or if you have an unlocked bootloader you can flash TWRP and use the build in file manager to transfer the files to your sd.
Click to expand...
Click to collapse
Hi,
Safe mode is not helping. Same loop is continuing.
Also, I am not able to flash TWRP custom recovery. I am getting the following message:
(bootloader) Preflash validation failed
FAILED (remote failure)
In phone bootloader logs I can see: "Mismatched partition size (recovery).

bablu048 said:
If bootloader is unlocked then recovering data is easy, I guess you have TWRP recovery if not flash twrp then pop in a sd-card boot into recovery and copy everything to the card. Done.
Edit: the above comment says the same thing, I had not noticed that .
Click to expand...
Click to collapse
While flashing TWRP recovery, I am getting the following message in CMD:
target reported max download size of 268435456 bytes
sending 'recovery' (8362 KB)...
OKAY [ 0.276s]
writing 'recovery'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.310s
In phone bootloader logs I can see: "Mismatched partition size (recovery).
Please help!

anujagraj said:
While flashing TWRP recovery, I am getting the following message in CMD:
target reported max download size of 268435456 bytes
sending 'recovery' (8362 KB)...
OKAY [ 0.276s]
writing 'recovery'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.310s
In phone bootloader logs I can see: "Mismatched partition size (recovery).
Please help!
Click to expand...
Click to collapse
is the bootloader unlocked, did you input the code to unlock??just checking

Yes. Bootlader is unlocked with input code to unlock.

I guess adb is not authorised then. when the phone is in setup wizard connect it to pc and type 'adb devices' there will be a pop-up asking you to authorise adb. select it. the try to flash recovery again .
---------- Post added at 07:47 AM ---------- Previous post was at 07:44 AM ----------
anujagraj said:
Yes. Bootlader is unlocked with input code to unlock.
Click to expand...
Click to collapse
or simply run
fastboot boot <enter twrp name>

bablu048 said:
I guess adb is not authorised then. when the phone is in setup wizard connect it to pc and type 'adb devices' there will be a pop-up asking you to authorise adb. select it. the try to flash recovery again .
---------- Post added at 07:47 AM ---------- Previous post was at 07:44 AM ----------
or simply run
fastboot boot <enter twrp name>
Click to expand...
Click to collapse
"adb devices" is not working during Setup wizard.
Do you mean to say that I run fastboot boot <enter twrp name> during setup wizard?
Also, alternatively, will flashing a rom without clearing user data help in any way?
Thanks a lot for the help..

bablu048 said:
I guess adb is not authorised then. when the phone is in setup wizard connect it to pc and type 'adb devices' there will be a pop-up asking you to authorise adb. select it. the try to flash recovery again .
---------- Post added at 07:47 AM ---------- Previous post was at 07:44 AM ----------
or simply run
fastboot boot <enter twrp name>
Click to expand...
Click to collapse
adb and fastboot are different things and are unrelated to each other. He doesn't need adb to flash the recovery.
anujagraj said:
"adb devices" is not working during Setup wizard.
Do you mean to say that I run fastboot boot <enter twrp name> during setup wizard?
Also, alternatively, will flashing a rom without clearing user data help in any way?
Thanks a lot for the help..
Click to expand...
Click to collapse
What happens when you just clear /cache in the stock recovery?
What recovery are you trying to flash?

Lennyz1988 said:
adb and fastboot are different things and are unrelated to each other. He doesn't need adb to flash the recovery.
What happens when you just clear /cache in the stock recovery?
What recovery are you trying to flash?
Click to expand...
Click to collapse
Clear /cache in the stock recovery didn't help. Also, I am trying to flash TWRP recovery 2.8.7.

no, boot phone in fastboot mode ...then run the command
fastboot boot <recovery>
try latest TWRP

bablu048 said:
no, boot phone in fastboot mode ...then run the command
fastboot boot <recovery>
try latest TWRP
Click to expand...
Click to collapse
Hi,
I tried re-unlocking the phone using code and got following message:
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.008s
Any workaround?

unlocking bootloader will wipe the data in your phone.
I thought you had unlocked.
what is the problem when you try to setup the phone ? or skip the setup
---------- Post added at 05:15 PM ---------- Previous post was at 05:12 PM ----------
anujagraj said:
Hi,
I tried re-unlocking the phone using code and got following message:
(bootloader) Check 'Allow OEM Unlock' in Developer Options.
FAILED (remote failure)
finished. total time: 0.008s
Any workaround?
Click to expand...
Click to collapse
best option now is flashing the firmware manually without wiping data.
Read this, also read a few comments after it.http://forum.xda-developers.com/showpost.php?p=65715334&postcount=43

bablu048 said:
unlocking bootloader will wipe the data in your phone.
I thought you had unlocked.
what is the problem when you try to setup the phone ? or skip the setup
---------- Post added at 05:15 PM ---------- Previous post was at 05:12 PM ----------
best option now is flashing the firmware manually without wiping data.
Read this, also read a few comments after it.http://forum.xda-developers.com/showpost.php?p=65715334&postcount=43
Click to expand...
Click to collapse
Hi,
Where can I find firmware to flash on my phone?
Also RSDLite is not able to detect phone. Can I enter commands from fastboot?
Thanks!

anujagraj said:
Hi,
Where can I find firmware to flash on my phone?
Also RSDLite is not able to detect phone. Can I enter commands from fastboot?
Thanks!
Click to expand...
Click to collapse
RSD lite needs windows 7.
Yes you have to flash manually then using fastboot commands.
firmware
Just don't use the command to erase user data. Skip it. Open the zip there will be flashfile. xml/servicefile.xml open it , you will find the list of commands to run. Or the commands can be found here.

bablu048 said:
RSD lite needs windows 7.
Yes you have to flash manually then using fastboot commands.
firmware
Just don't use the command to erase user data. Skip it. Open the zip there will be flashfile. xml/servicefile.xml open it , you will find the list of commands to run. Or the commands can be found here.
Click to expand...
Click to collapse
Just to confirm, will any firmware will work or I need to download one specific to my phone/higher version?
Also, any risks of bricking the device while flashing?

anujagraj said:
Just to confirm, will any firmware will work or I need to download one specific to my phone/higher version?
Also, any risks of bricking the device while flashing?
Click to expand...
Click to collapse
If you are on 6.0.1 then flash 6.0.1...better flash the appropriate region firmware.
There is a risk of bricking if you are downgrading and flash old gpt.bin and bootloader
As long as you are flashing proper firmware it's safe thoughi haven't done it but as you can see the comments I linked previously others have done it.

bablu048 said:
If you are on 6.0.1 then flash 6.0.1...better flash the appropriate region firmware.
There is a risk of bricking if you are downgrading and flash old gpt.bin and bootloader
As long as you are flashing proper firmware it's safe thoughi haven't done it but as you can see the comments I linked previously others have done it.
Click to expand...
Click to collapse
Hi,
I have an Indian model and got the following error on flashing contents of XT1562_LUX_RETASIA_DS_6.0_MPD24.65-18.1_cid7_subsidy-DEFAULT_CFC.xml using fastboot:
AP Fastboot Flash Mode (Secure)
failed to validate system image
ERROR: Failed to pass validation, backup to fastboot
Fastboot Reason: Fall-through from charger boot mode
Please help!