Hi! After flash my Acer S200 don't start. Just write : Cleen Boot ACER.
If someoane can help me I waitt your sugestion. Thank's very mutch.
surdu_petru said:
Hi! After flash my Acer S200 don't start. Just write : Cleen Boot ACER.
If someoane can help me I waitt your sugestion. Thank's very mutch.
Click to expand...
Click to collapse
What ROM did you flash? sounds like a bad flash... reflash, or try a different ROM
Hello!
Thank's very much, but how can I reflash if the phone dosen't start?
If someoane have the same problem please tell me how can I reflash the phone. Thank's .
surdu_petru said:
Thank's very much, but how can I reflash if the phone dosen't start?
If someoane have the same problem please tell me how can I reflash the phone. Thank's .
Click to expand...
Click to collapse
you didn't break your device , you can reflash it following the flash instructions included , for an example , in rafyvitto's rom's post .Just have a look there .
surdu_petru said:
Thank's very much, but how can I reflash if the phone dosen't start?
If someoane have the same problem please tell me how can I reflash the phone. Thank's .
Click to expand...
Click to collapse
If it dosnt start by camera press button and hold then reset button(this puts device in bootloader mode) if that doesn't place your device in bootloader mode its brick't, thats is if you have the 1.00 radio.
Hi!
rafyvitto said:
If it dosnt start by camera press button and hold then reset button(this puts device in bootloader mode) if that doesn't place your device in bootloader mode its brick't, thats is if you have the 1.00 radio.
Click to expand...
Click to collapse
Thank's Rafyvitto , but I press camera button end hold reset , the phone don't start, just write in black screen with white : S200_3.003b.00_EN
Clean Boot
acer
end don't work , don't start . I waitt 1 hour but the screen dosen't change , it's the same screen like begining. I don't know what I make , maybe I flesh it with a wrong rom , but now if you know ? it's posibile flash again or make something for start , if the phone don't start? Thank's very much....
You can save it, cause the screen that says "clean boot" is the bootloader, so you just need to press the bootloader combination of the 2.00 radio, press power + volume + camera holding all these press reset, if you see a red led blinking then its in bootloader mode, and you can flash your device.
Hi!
rafyvitto said:
You can save it, cause the screen that says "clean boot" is the bootloader, so you just need to press the bootloader combination of the 2.00 radio, press power + volume + camera holding all these press reset, if you see a red led blinking then its in bootloader mode, and you can flash your device.
Click to expand...
Click to collapse
I will try now. Thank's again.
Hi!
rafyvitto said:
You can save it, cause the screen that says "clean boot" is the bootloader, so you just need to press the bootloader combination of the 2.00 radio, press power + volume + camera holding all these press reset, if you see a red led blinking then its in bootloader mode, and you can flash your device.
Click to expand...
Click to collapse
No, my Acer S200 don't want to start reflash, I try exactaly end the red led is blinking but the all the flash rom don't start....just say update failure veryfi the connection USB. I trying with the Acer_EUU haker version 1 end 2. I thing that the phone is dad. Maybe is another solutions? I waitt...Thank's again, very much.
Heelo!
If you know , maybe it 's an solution for boot the rom on the storage card ? I thing , if the phone don't connect with the pc with usb cable is normaly that the flash don't start, maybe if I put the rom on the storage card then the phone will try to boot on the storage card, but I don't know how to make that. Thank's again.....
Hi!
Greats thank's again Rafivitto! I will try press cammera + volume + power end reset and the phone start the reflash. Merci beaucup.....
Hy all!
I have problem with clean boot logon... I done hard reset and device stuck at Clean Boot logon...
Would like to know how to flash it without activesync? I downloaded OEM ROM just can not install it without the NeoTouche beeing synchronized via active sync...
Please help how to do that without active sync...
Hi!
matjazz said:
Hy all!
I have problem with clean boot logon... I done hard reset and device stuck at Clean Boot logon...
Would like to know how to flash it without activesync? I downloaded OEM ROM just can not install it without the NeoTouche beeing synchronized via active sync...
Please help how to do that without active sync...
Click to expand...
Click to collapse
You need active sync for flash your s200 , so you plug usb cable between pc end phone with micro usb. After that you need to entre in bootloader mode ( for bootloader mode you need press simultanly power , camera end volume end reset while the red led is blinking) . If your led red is blinking then you can start flash rom with any flash , but I recomanded for you an original flash with ACER_EUU.exe hack , not originaly for that just download hack acer_euu.exe end replace it in directory flash rom. If you still can't make the reflash I need to know what is your version of rom? Your version is in the left corner on the first line. See you later....
update failed
Hello,
I wanted to update Neotouch from official rom 2.003.00_de to 3.003c.00_de.
The update failed and when i start the device, now I see on display:
- in the upper left corner: s200_3.003c.00_DE
- in the middle "clean boot"
- under it "acer"
I tryed to go in the bootloader mode:
I removed the Akku for ca. 10sek.
I connected device and PC via usb.
I pressed Volume down + camera buttons together, then the power button and when it starts to blinking the LED red, I press reset with the pen.
The LED is blinking red, but the display is black?
(it is correct?)
Then I started on PC the "EUU_Acer_S200_3.003c.00_DE_03.03.08_3.003c.00_20100205.exe"
...extracting...install prompt...ok...
window: "welcome to the device software update utility" etc. with the notifications to connect
... next..
and then:
"Update failed. The device software utility occurs trouble connecting to your device"
what am I doing wrong?
surdu or other , can you help?
Thanks!
I unpacked the originial
"EUU_Acer_S200_3.003c.00_DE_03.03.08_3.003c.00_201 00205.exe"
and replace the "ACER_EUU.exe" with
File
from this Thread
http://forum.xda-developers.com/showthread.php?t=628402
Then I clicked the "EUUFrontEnd.exe" and the "install prompt" started, then for a second, there is an Error window.
I searched in the posts here in neotouch forum for this problem, but idont understand much and my english is very bad.
Iam only user, I have no background knowledge. Please help me, if you can.
did you bring your device on "flash mode"?
what rom does it have now?
When I bouhgt mine I did excactly the same thing
It had 2.003.... official ROM and I flashed it with the new official 3.003b.....
camera+reset and then the steps as you did.
maybe it's something in the 3.003c drivers and the hacked .exe does not work..
Philippe_Raimo said:
did you bring your device on "flash mode"?
what rom does it have now?
Click to expand...
Click to collapse
1. I do not know exactly...
"I pressed Volume down + camera buttons together, then the power button and when it starts to blinking the LED red, I press reset with the pen.
The LED is blinking red, but the display is black?
(it is correct?)"
Is this really the Bootload Mode?
2. see my Post Nr. 14
Now i can see upper left corner: s200_3.003c.00_DE
maybe it's something in the 3.003c drivers and the hacked .exe does not work..
Click to expand...
Click to collapse
mmh..what should i do...
Hi!
olsching said:
1. I do not know exactly...
"I pressed Volume down + camera buttons together, then the power button and when it starts to blinking the LED red, I press reset with the pen.
The LED is blinking red, but the display is black?
(it is correct?)"
Is this really the Bootload Mode?
2. see my Post Nr. 14
Now i can see upper left corner: s200_3.003c.00_DE
Your phone S200 is not dead, you can save it, but is 2 way from the led red blinking, if your led red is on/off very well then is the bootloader, if the red led is blinking with have a small break (off) then you aren't in bootloader. Then you need press the Volume down + camera buttons + power button + reset with the pen , all the button togheter, while the red led is blinking (on / off) quickly end now you are in bootloader. After that you need Acer_EUU.exe Hack version v1 ( is exactaly - 3.432.960k ) .Just replace it end go. Good luck!
Click to expand...
Click to collapse
Hi Olscing! again
from this Thread
http://forum.xda-developers.com/showthread.php?t=628402 you download Hack v2 is no't good for you. You need v1 end the Acer S200_2.003.00_EN.
neotouch is running again
Thanks for your help surdu!
But now i could help myself
I flashed a customrom here from the forum. It stopped at 99,2%!
But the device was able to start and the rom runs.
Then i started the official acer update again and without problems it was installed. Now i happy again!
Hi,
Is it possible to install a rom on my N1 from the computer? ( like we do with winmo)
The power button of the phone is broken, and I can't copy the zip file into the sdcard.
plz help me
your power button is broken and you can't mount the SD card?
I used dropbox to install a bunch of stuff a few times when I had broke kernels.
So how do you get to recovery? rom manager?
I've nothing at this moment, my phone is turned off ( the battery was removed);
so I can't boot the phone or get the recovery mode.
I don't know if there is a solution to get something from computer.
Search the forum (and Q&A section too), the way to power on a phone with dead power button has been discussed.
Once you're powered on - you can use reboot commands to get to recovery, etc.
I've really tried to search, but I didn't find an answer (probably because my english is poor).
If you know where to find the answer, could you plz give the url, I will follow the discuss on that thread.
thanks a lot
http://forum.xda-developers.com/showthread.php?t=736054&highlight=power+button
Thanks for the link,
I've tried all day but my phone will not turn on.
I dont know what to do now.
My phone is bricked ?
Plz, can someone help me ?
I've tried to boot the phone ( like described here in different post) but it doesn't
work for me. The phone turn on except the screen which is still turn off.
I hope there is e solution to boot my phone.
You can power on the phone by plugin usb cable, wait until led goes on, immediately pull of battery and wait until led goes of, then plugin battery back and phone should power on.
After that you can boot to bootloader by pressing trackball and from there you can go to recovery or install new rom using fastboot.
hi houmles,
thx for your help. I've tried exactely like you said, but the screen is still turn off.
I've pressed the trackball but nothing happend, just tthe sensitives keys backlight turned on.
Maybe I'm do it wrong.
You should try this application called droid explorer
Sent from my Nexus One using XDA App
If the soft keys turn on the phone is on......is there a light in the upper right of the screen The charging light? Have you opened the nexus? Possibly the connector is off or lose for the screen? Or the screen is broke from dropping or water?
Hi.
I installed the rom here:
http://forum.xda-developers.com/showthread.php?t=1311565
When you turn on I get a blue screen and I can not do anything else.
A greeting and thanks.
Which blue screen?
Do you mean recovery screen? In recovery you move with volume up and down.
Also what device do you have and what stock rom did you have before you did something?! That would help...
boss_y said:
Which blue screen?
Do you mean recovery screen? In recovery you move with volume up and down.
Also what device do you have and what stock rom did you have before you did something?! That would help...
Click to expand...
Click to collapse
only a complete blue screen with no letters or anything. Spain had one of movistar (factory)
Edit: In the image folder nothing comes
HELP ME PLEASE
Do you have an U8800 or U8800-Pro/H/51? If you don't know, look under the battery...
Try to get a hold of official firmware (Huawei site) for your phone, put on sd-card and flash it by normal means, e.g. vol-up + vol-down + power...
Also, factory reset / clear cache etc...
Variant 1: Blue screen means that it is lost folder IMAGE in startup partition. Connect your phone to computer if you have a blue screen and copy original folder IMAGE to storage which you appeared in Explorer.
Variant 2: Also try to delete the cache and restore default settings as described in the previous thread
It was happen to me,when i change image file with new one image file,when i reboot n i want in cwm than blue screen.
If you have backup the image file i suggest you change it with your backup image file,cause it work to my x5 n now.
Sent from my U8800Pro using xda premium
Hey
After updating my S5 to the laste software (15 may). Im having trouble root'ing my phone again.
When i try to put my phone into recovey mode I get a new screen then I use to get, when rooting. (see Attach File)
Im not sure what option to use. So if anyone plz can help, I be gretfull
Paland49 said:
Hey
After updating my S5 to the laste software (15 may). Im having trouble root'ing my phone again.
When i try to put my phone into recovey mode I get a new screen then I use to get, when rooting. (see Attach File)
Im not sure what option to use. So if anyone plz can help, I be gretfull
Click to expand...
Click to collapse
you're doing it in wrong way bro, you have to switch to "download mode", not "recovery mode"
power off your device, then hold these 3 buttons at a time: power button + home button + down volume
Thank you.
I was holding up volume, insted of down
Feeling abit silly now
you're welcome
I know. It's dumb. I didn't read all those walls of text and now I'm paying for it. Is there anything I can do or is the phone gone for good? I tried to boot into bootloader by holding down the volume and connecting the usb cable but it just goes into a black screen with a green led instead of the usual blue led that would pop up when being in bootloader. Right now it's just stuck in loading screen with the logo and it won't even shut down
Hey i accidentally flash wrong twrp on my f3311. it's pretty easy to fix it.
1. Download flashtool (flashtool .net)
2. Find the stock rom for your phone.
3. Start flash tool and press the flash button and choose flashmode.
4. choose the rom file and the settings you want.
5. click on flash and it will guide you how to get into flashmode
I hope i explained so you can understand, my English is trash and i dont remember exactly how to do it. And here is a video how to do it. watch?v=q7zDA94gqdc