I installed CyanogenMod 10.2.1 on my rooted Sprint S4. Upon realizing that I could no longer connect my Gear 2 watch to my phone, I would like to reset my phone to factory settings, unrooted, with the stock ROM. I followed the guide at galaxys4root.com (xda won't let me post the outside link, but it is the first result when you Google "galaxy s4 root unroot") and used all the downloads from that page. However, upon trying to flash to my phone, I receive this error in Odin:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNAE_L720SPTFNAE_L720VPUFNAE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can then shut down my phone and reboot back into CM just fine, but I really would like to have the stock ROM back so I can use my watch. If anyone could help me with this, I'd really appreciate it. Thanks!
GadgetGuy3 said:
I installed CyanogenMod 10.2.1 on my rooted Sprint S4. Upon realizing that I could no longer connect my Gear 2 watch to my phone, I would like to reset my phone to factory settings, unrooted, with the stock ROM. I followed the guide at galaxys4root.com (xda won't let me post the outside link, but it is the first result when you Google "galaxy s4 root unroot") and used all the downloads from that page. However, upon trying to flash to my phone, I receive this error in Odin:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNAE_L720SPTFNAE_L720VPUFNAE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can then shut down my phone and reboot back into CM just fine, but I really would like to have the stock ROM back so I can use my watch. If anyone could help me with this, I'd really appreciate it. Thanks!
Click to expand...
Click to collapse
What version of ODIN are you using?
pontif said:
What version of ODIN are you using?
Click to expand...
Click to collapse
I've tried both 1.85 and 3.04, both present the same error
GadgetGuy3 said:
I've tried both 1.85 and 3.04, both present the same error
Click to expand...
Click to collapse
The stock nae forum suggests using 3.07
Put in pda slot
Be sure to power completely off before going into download mode
pontif said:
The stock nae forum suggests using 3.07
Put in pda slot
Be sure to power completely off before going into download mode
Click to expand...
Click to collapse
Just did all that, still got the error:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNAE_L720SPTFNAE_L720VPUFNAE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Attaced is a photo of the screen of my phone after the flash fails. In case you can't read it, the text in the top-left corner says:
ODIN MODE
PRODUCT NAME: SPH-L720T
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
WRITE PROTECTION: Enable
eMAC BURST MODE: enabled
START [244, 1440]
SECURE CHECK FAIL : aboot
Since you have the file already here is the link from Sammmobile. Also if you want ,download the Odin version that they provide. GoodLuck
GadgetGuy3 said:
Just did all that, still got the error:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNAE_L720SPTFNAE_L720VPUFNAE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Attaced is a photo of the screen of my phone after the flash fails. In case you can't read it, the text in the top-left corner says:
ODIN MODE
PRODUCT NAME: SPH-L720T
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
WRITE PROTECTION: Enable
eMAC BURST MODE: enabled
START [244, 1440]
SECURE CHECK FAIL : aboot
Click to expand...
Click to collapse
Well there's you problem says you have the l720T version of the s4. You need stock firmware for the sphl720 T version. Search for that specific device
BIGSAMDA1ST said:
Since you have the file already here is the link from Sammmobile. Also if you want ,download the Odin version that they provide. GoodLuck
Click to expand...
Click to collapse
There's no link in this post
Holy S*#@. Anyway just saw that @pontif just posted that you have the T version so the link I provided will not work.
---------- Post added at 01:57 PM ---------- Previous post was at 01:50 PM ----------
Here you go.. Its the latest for SPH-L720T
http://www.sammobile.com/firmwares/3/?download=28778
BIGSAMDA1ST said:
Holy S*#@. Anyway just saw that @pontif just posted that you have the T version so the link I provided will not work.
---------- Post added at 01:57 PM ---------- Previous post was at 01:50 PM ----------
Here you go.. Its the latest for SPH-L720T
Click to expand...
Click to collapse
pontif said:
Well there's you problem says you have the l720T version of the s4. You need stock firmware for the sphl720 T version. Search for that specific device
Click to expand...
Click to collapse
Alright, that was a stupid mistake on my part, I apologize. I'm downloading the L720T firmware from Sammobile now and I also downloaded Sammoblie's suggested ODIN, which is 3.09. I will post the results after the download finished and I try to flash it.
GadgetGuy3 said:
Alright, that was a stupid mistake on my part, I apologize. I'm downloading the L720T firmware from Sammobile now and I also downloaded Sammoblie's suggested ODIN, which is 3.09. I will post the results after the download finished and I try to flash it.
Click to expand...
Click to collapse
That worked. Thanks for your help.
PLZ HELP!!!
Hi, I am having the EXACT same issue but with SPH-L720 device. I've tried multiple odin's.....STILL....."FAILED"
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNAE_L720SPTFNAE_L720VPUFNAE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I desperately need to return to stock so I can update my device. It is not running well AT ALL.
Thanks in advance.
bbryson said:
Hi, I am having the EXACT same issue but with SPH-L720 device. I've tried multiple odin's.....STILL....."FAILED"
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNAE_L720SPTFNAE_L720VPUFNAE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I desperately need to return to stock so I can update my device. It is not running well AT ALL.
Thanks in advance.
Click to expand...
Click to collapse
Try downloading the NG2.tar. It's the most up to date.
Will do. Thank you!
Related
I rooted my s4 just to try it and I'm stuck trying to get it to go back to stock.
I have a note 3 now and I've got everything going well with that but the s4 (I have the I337).
I have it rooted and the phone will start and is a perfectly functional android phone, but whenever I try to get it into recovery mode I can only get it to go to download mode. Odin flashes to stock fail with this:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
the stock flash was linked to by others I found on XDA.
Also, details about the phone:
Jelly Bean 4.2.2
Baseband I337UCAMF3
Clockworkmod 6.0.4.4
Thanks for any and all help!
attbrandon said:
I rooted my s4 just to try it and I'm stuck trying to get it to go back to stock.
I have a note 3 now and I've got everything going well with that but the s4 (I have the I337).
I have it rooted and the phone will start and is a perfectly functional android phone, but whenever I try to get it into recovery mode I can only get it to go to download mode. Odin flashes to stock fail with this:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
the stock flash was linked to by others I found on XDA.
Also, details about the phone:
Jelly Bean 4.2.2
Baseband I337UCAMF3
Clockworkmod 6.0.4.4
Thanks for any and all help!
Click to expand...
Click to collapse
You cannot add a custom recovery to MF3 if the phone came with that firmware you will get hard brick
Sent From My Galaxy S4 SAMSUNG-SGH-I337 Running On New Deadly Venom v1.3.6 Jelly Bean 4.3
---------- Post added at 04:55 PM ---------- Previous post was at 04:51 PM ----------
Venom0642 said:
You cannot add a custom recovery to MF3 if the phone came with that firmware you will get hard brick
Sent From My Galaxy S4 SAMSUNG-SGH-I337 Running On New Deadly Venom v1.3.6 Jelly Bean 4.3
Click to expand...
Click to collapse
I wish I could help more but I'm on the road hopefully someone will explain it better then what I mention.
Sent From My Galaxy S4 SAMSUNG-SGH-I337 Running On New Deadly Venom v1.3.6 Jelly Bean 4.3
Because you are on MF3, the bootloader is locked and there is no exploit. Therefore, custom recoveries won't install. The reason ODIN is failing is because you are using the MDB files instead of MF3. It is impossible to downgrade the firmware back to any previous version. If you want a recovery, the most you can get is Safestrap, but make sure you read up plenty on it before you install it, as it is not a normal recovery and is not even installed to the recovery partition.
need help
every time i try to reset my galaxy s4 att to stock it fails heres what it says
<OSM> Enter CS for MD5.. <OSM> Check MD5.. Do not unplug the cable.. <OSM> Please wait.. <OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid. <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS.. <ID:0/005> Added!! <ID:0/005> Odin v.3 engine (ID:5).. <ID:0/005> File analysis.. <ID:0/005> SetupConnection.. <ID:0/005> Initialzation.. <ID:0/005> Get PIT for mapping.. <ID:0/005> Firmware update start.. <ID:0/005> aboot.mbn <ID:0/005> NAND Write Start!! <ID:0/005> FAIL! (Auth) <OSM> All threads completed. (succeed 0 / failed 1)
ramiijabedd said:
every time i try to reset my galaxy s4 att to stock it fails heres what it says
<OSM> Enter CS for MD5.. <OSM> Check MD5.. Do not unplug the cable.. <OSM> Please wait.. <OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid. <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS.. <ID:0/005> Added!! <ID:0/005> Odin v.3 engine (ID:5).. <ID:0/005> File analysis.. <ID:0/005> SetupConnection.. <ID:0/005> Initialzation.. <ID:0/005> Get PIT for mapping.. <ID:0/005> Firmware update start.. <ID:0/005> aboot.mbn <ID:0/005> NAND Write Start!! <ID:0/005> FAIL! (Auth) <OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Grab the MF3 Odin flashable tars and flash them the same way to get back to complete factory stock. Or you can get the MK2 tars and update to 4.3 and use Saferoot to easily get root since you already have drivers installed. Then look up how to install Safestrap for MK2, (which is really not too difficult), and TWRP v3.71to use as a recovery.
Hi I am very new to this rooting thing, im trying to unroot my galaxy s4 AT&T. I have used oden and the stock firmware I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar I get an fail right when odin starts it says this
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
is this the wrong firmware? im sorry for such a boot questions but I have no idea what to do. Thank you for all your help. I am on android 4.3
Wrong firmware you need the MK2 Odin . Use the full odin in the pda slot http://forum.xda-developers.com/showthread.php?t=2621279
Sent from my SAMSUNG-SGH-I337 using Tapatalk
Im in a bit of a dilemma. I bought a new s5 with lollipop already installed on it and decided to root it. To root i needed to downgrade it. So using Odin, i attempted a downgrade only to come to a FAIL conclusion. I tried different .tar files that were kit kat, also found rooted lollipop firmware which always failed. I tried using a pit file which didnt seem to help. I cleared the cached and wiped the system memory multiple times. The only screen i am able to see is the Downloading screen and the reboot screen (volume up, home, and power)
I guess i soft bricked my phone... is there anyway to fix this problem?
Thanks a lot
AT&T - Bootloader is locked, don't think there is any way to downgrade from Lollipop
*Detection* said:
AT&T - Bootloader is locked, don't think there is any way to downgrade from Lollipop
Click to expand...
Click to collapse
yea that i realized, but is there anyway to get my phone back to its original state? Or because the bootloader is locked, this phone is forever soft bricked?
yakmicjan said:
yea that i realized, but is there anyway to get my phone back to its original state? Or because the bootloader is locked, this phone is forever soft bricked?
Click to expand...
Click to collapse
Boot in download mode then flash a LP firmware with odin
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Boot in download mode then flash a LP firmware with odin
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
I'm sorry what is LP firmware? If you mean stock, then I've already tried a lollipop firmware download with Odin which also always kept failing
yakmicjan said:
I'm sorry what is LP firmware? If you mean stock, then I've already tried a lollipop firmware download with Odin which also always kept failing
Click to expand...
Click to collapse
Yeah "LP" mean lollipop. Which fail message do you get ?
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Yeah "LP" mean lollipop. Which fail message do you get ?
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
First off, i used a few different update files. I'll just list the errors i get with each of them if that makes a difference:
*****
G900AUCU3BOC4_OneClick.exe (Can't add a pit file into this... it's a custom ODIN
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> One Click Downloader Mode
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005>
<ID:0/005>
<OSM> All threads completed. (succeed 0 / failed 1)
*****
Both of these files get the same error
AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5
AND
G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 (added a pit file : SM-G900A_pit.pit)
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
In addition, i also tried to update the phone through an sd card using the file G900A-OF3toOI5-ota-2400258.cfg and renaming it to update.zip. Through the recovery menu, i wiped cache partition and did a factory reset. Then I applyed the update from external storage and get an Error Status 7.
This is everything i tried. Im running out of ideas and getting frustrated as this is a brand new phone
@yakmicjan But why are you using a modded version of odin ? Use a normal one , took the last version , then go to sammobile donwload the last firmware for your phone. Extract it and flash it with odin. It should work
Don't flash any pit file with it or anything , just the firmware.
Sent from my SM-G900F using XDA Free mobile app
I downloaded so many different types of odins and tried these files on all of them. The only modded version of odin is on the .exe file. I tried Odin3 v1.85, 3.10.6, 3.09. All of them gave me the same exact message.
Sadly, on sam mobile, the very last version they have for SM G900A is 4.4.2 which doesnt help since my phone already had lollipop installed on it. Does this mean i have to wait until they get a lollipop firmware for me to use my phone?
yakmicjan said:
I downloaded so many different types of odins and tried these files on all of them. The only modded version of odin is on the .exe file. I tried Odin3 v1.85, 3.10.6, 3.09. All of them gave me the same exact message.
Click to expand...
Click to collapse
Wait i just saw "Re-partion failed" , was it ticked before the flash ? Make sure only auto reboot and Reset time are ticked.
Sent from my SM-G900F using XDA Free mobile app
yakmicjan said:
This is everything i tried. Im running out of ideas and getting frustrated as this is a brand new phone
Click to expand...
Click to collapse
That's why you spend time reading and learning before just jumping in without knowing anything
Send it back, hope that they fix it under warranty
Soufiansky said:
Wait i just saw "Re-partion failed" , was it ticked before the flash ?
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
No it wasnt. I only have Auto Reboot and F.Reset Time ticked
Here is another error i'm getting. This time i added an AP, CP, and CSC file
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_G900AATT1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
yakmicjan said:
Here is another error i'm getting. This time i added an AP, CP, and CSC file
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_G900AATT1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Why do you add PIT FILE ? DO NOT DO IT. Flash only the firmware with Re-partition unchecked
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Why do you add PIT FILE ? DO NOT DO IT. Flash only the firmware with Re-partition unchecked
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
Im not adding the Pit File at all. I dont know why it shows up. I'll attach proof.
By the way, its the same exact error message as above.
Im so sorry about this annoying problem and for me being such a bother. Thank you so much for trying to help me
Why are you adding anything other than just the ROM in AP?
Remove everything from ODIN, and only add the ROM in AP
yakmicjan said:
Im not adding the Pit File at all. I dont know why it shows up. I'll attach proof.
By the way, its the same exact error message as above.
Click to expand...
Click to collapse
Look , choose ONLY the rom which is a very big .tar file and put it in AP , that's it. Do not add anything , anything. The firmware is about 2.4/2.5 go , you flash it and that's it
Sent from my SM-G900F using XDA Free mobile app
Soufiansky said:
Look , choose ONLY the rom which is a very big .tar file and put it in AP , that's it. Do not add anything , anything. The firmware is about 2.4/2.5 go , you flash it and that's it
Sent from my SM-G900F using XDA Free mobile app
Click to expand...
Click to collapse
What i am using now is the firmware i got from Sam's. I also tried checking and unchecking F. Reset Time. It gave me the same results
Same problem:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_G900AUCU1ANCE_964333_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Hey guys, I m trying to flash stock rom on my S3 Neo GT-I9301I but i dont work. here is odin code. i tried almost everything please help. it stucks always. even when i try to install a recovery it stucks at recovery.img. again here is the code
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G7102XXUBNG4_G7102ODDBNG4_G7102DDUBNF4_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
PLEASE HELP ME GUYS :crying::crying:
You have selected the wrong file, that is for another smartphone
Alessandro's said:
You have selected the wrong file, that is for another smartphone
Click to expand...
Click to collapse
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXXUANL1_I9301IOXAUANL1_I9301IXXUANI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
My device is normaly a GT-I9301I but i suddenly installed GT-I9300I. The only things i can do with phone right now is: entering recovery(twrp) and downlaod mod.
I want now the stock rom of GT-I9301I what can i do now?? :crying::crying:
Flash the right firmware for your phone.
Jhnsn said:
Flash the right firmware for your phone.
Click to expand...
Click to collapse
As you can see the odin code above it stucks at sbl1.mdn or am i doing something wrong?
I tried it with another Firmware
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXXUAOJ1_I9301ITTRAOH2_I9301IXXUAOD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
again Stuck
No mather what firmware i try to install everytime it stucks
HELP PLEASE
AnroidLover said:
Hey guys, I m trying to flash stock rom on my S3 Neo GT-I9301I but i dont work. here is odin code. i tried almost everything please help. it stucks always. even when i try to install a recovery it stucks at recovery.img. again here is the code
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G7102XXUBNG4_G7102ODDBNG4_G7102DDUBNF4_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
PLEASE HELP ME GUYS :crying::crying:
Click to expand...
Click to collapse
or try another version of odin
Alessandro's said:
or try another version of odin
Click to expand...
Click to collapse
already tried. but where should i put the firmware? PDA, CSC, PHONE, AP? i tried already AP and PDA and almost every version of odin
http://www.sammobile.com/firmwares/download/64471/I9301IXCUAOL3_I9301IITVAOL1_ITV/
this is one of the latest firmware avaiable on sammobile for gt-i9301i
http://forum.xda-developers.com/attachment.php?attachmentid=1140630
this is odin
Alessandro's said:
http://www.sammobile.com/firmwares/download/64471/I9301IXCUAOL3_I9301IITVAOL1_ITV/
this is one of the latest firmware avaiable on sammobile for gt-i9301i
http://forum.xda-developers.com/attachment.php?attachmentid=1140630
this is odin
Click to expand...
Click to collapse
Thank u A lot, i m gonna try it.
AnroidLover said:
already tried. but where should i put the firmware? PDA, CSC, PHONE, AP? i tried already AP and PDA and almost every version of odin
Click to expand...
Click to collapse
in the newer version of odin AP is the same of PDA
of the older version
Alessandro's said:
http://www.sammobile.com/firmwares/download/64471/I9301IXCUAOL3_I9301IITVAOL1_ITV/
this is one of the latest firmware avaiable on sammobile for gt-i9301i
http://forum.xda-developers.com/attachment.php?attachmentid=1140630
this is odin
Click to expand...
Click to collapse
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Failed :crying:
WAY 1 : ------- VERY DANGEROUS, NOT TESTED, I'M NOT REAPONSIBLE FOR ANY DAMAGE DONE TO YOUR DEVICE, I WARNED YOU.
You need to get TWRP recovery, then download the Utility from HERE and then mount everything, so that your computer can access your device and then put your Utility wherever you want. Then go to install and select the utility.zip and after the program opens then go to next > primary > wipe System and cache and data and dalvik cache... MAKE A BACKUP FIRST! and then go to ODIN mode and flash your OS...
WAY 2 ----- BETTER
Go to TWRP, wipe all data including system and go to ODIN mode and flash the OS, NOT TESTED ASWELL BUT TRY WITHOUT DELETING SYSTEM FIRST!!!
WAY 3 -------
Flash a custom ROM like CM... if you need help at it, ASK! I'll reply to you as soon as possible!
Good Luck!
FireGhost1337 said:
WAY 1 : ------- VERY DANGEROUS, NOT TESTED, I'M NOT REAPONSIBLE FOR ANY DAMAGE DONE TO YOUR DEVICE, I WARNED YOU.
You need to get TWRP recovery, then download the Utility from HERE and then mount everything, so that your computer can access your device and then put your Utility wherever you want. Then go to install and select the utility.zip and after the program opens then go to next > primary > wipe System and cache and data and dalvik cache... MAKE A BACKUP FIRST! and then go to ODIN mode and flash your OS...
WAY 2 ----- BETTER
Go to TWRP, wipe all data including system and go to ODIN mode and flash the OS, NOT TESTED ASWELL BUT TRY WITHOUT DELETING SYSTEM FIRST!!!
WAY 3 -------
Flash a custom ROM like CM... if you need help at it, ASK! I'll reply to you as soon as possible!
Good Luck!
Click to expand...
Click to collapse
WAY 1
---------
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WAY 2
---------
Tried allready. Non worked for me. Like always Stuck.
WAY 3
---------
Tried. It bring me back to recovery when i m trying to boot it
AnroidLover said:
WAY 1
---------
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WAY 2
---------
Tried allready. Non worked for me. Like always Stuck.
WAY 3
---------
Tried. It bring me back to recovery when i m trying to boot it
Click to expand...
Click to collapse
Hmm... seems to be a very advanced error but don't worry!
WAY 4 ---------- Safest
Install newest odin and don't check anything in ODIN's settings, the rom will do all that stuff
---------- Post added at 06:48 PM ---------- Previous post was at 06:45 PM ----------
AnroidLover said:
WAY 1
---------
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WAY 2
---------
Tried allready. Non worked for me. Like always Stuck.
WAY 3
---------
Tried. It bring me back to recovery when i m trying to boot it
Click to expand...
Click to collapse
Oh by the way you made way 3? You installed the custom rom? As a zip file? Like Cyanogen? And it took you back to recovery? What recovery do you have? And did you UNCHECK the signature check? IT'S VERY IMPORTANT
FireGhost1337 said:
Hmm... seems to be a very advanced error but don't worry!
WAY 4 ---------- Safest
Install newest odin and don't check anything in ODIN's settings, the rom will do all that stuff
---------- Post added at 06:48 PM ---------- Previous post was at 06:45 PM ----------
Oh by the way you made way 3? You installed the custom rom? As a zip file? Like Cyanogen? And it took you back to recovery? What recovery do you have? And did you UNCHECK the signature check? IT'S VERY IMPORTANT
Click to expand...
Click to collapse
I installed Revolution HD as a zip file and i m using TWRP and yes it took me back. Zip file signature was and is unchecked. When i was installing the custom rom everything went fine with the installation of the custom rom.
And u mean with the settings F. Reset Time and other Stuff like that? And where should i put the stock rom? CSC or AP?
I tried with AP :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
By the way my downlaod settings are:
ODIN MODE
PRODUCT NAME: GT-I9300I (ist falsche rom. muss GT-I9301I)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
AnroidLover said:
I installed Revolution HD as a zip file and i m using TWRP and yes it took me back. Zip file signature was and is unchecked. When i was installing the custom rom everything went fine with the installation of the custom rom.
And u mean with the settings F. Reset Time and other Stuff like that? And where should i put the stock rom? CSC or AP?
I tried with AP :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
By the way my downlaod settings are:
ODIN MODE
PRODUCT NAME: GT-I9300I (ist falsche rom. muss GT-I9301I)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
Click to expand...
Click to collapse
Try to change cable usb
Alessandro's said:
Try to change cable usb
Click to expand...
Click to collapse
I tried. Failed again ! :crying::crying:
HELP ME PLEASE :crying::crying:
Alessandro's said:
Click to expand...
Click to collapse
That problem is omg. I dont know where the problem is :crying:
Alessandro's said:
Click to expand...
Click to collapse
Hey Jow, i got another usb cable. Now its says always Unknwon Device (also in Odin no added Message)
Here's the odin message,
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T337AUCU1ANF4_T337AATT1ANF4_T337AUCU1ANF4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Help Would be much appreciated!
SpiffyM said:
Here's the odin message,
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T337AUCU1ANF4_T337AATT1ANF4_T337AUCU1ANF4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Help Would be much appreciated!
Click to expand...
Click to collapse
Download and use this instead of the NF4 file, should work like a charm. https://mega.nz/#!0Q4AXQgZ!Df-pTUo6eA80kGTrzpYCAJ0ilGbUzMYCE4nRtvume6s
CocaFoca said:
Download and use this instead of the NF4 file, should work like a charm.
Would this go in place of the current T337 file in the PDA section of ODIN?
Click to expand...
Click to collapse
CocaFoca said:
Download and use this instead of the NF4 file, should work like a charm.
It did not work. Here's the odin error.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MD5 hash value is invalid
<OSM> T337AUCU2BOH4_T337AATT2BOH4_HOME.tar.md5 is invalid.
<OSM> End...
Click to expand...
Click to collapse
CocaFoca said:
Download and use this instead of the NF4 file, should work like a charm.
After all the previous items, I found a previous valid file for the PDA section, here's odins message.
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse