Database Users

[Q] Soft brick? Hard brick? Sort of firm'ish brick really

I've made a bit of a mess and I need help please. My s4 is softbricked, but as softbricks go, it's rather hard.
I have an early S4 i9505 bought from Carphone Warehouse (UK, unlocked, pre knox). I rooted it, installed TBackup, greenify and got it how I wanted it. Then I downloaded a stock firmware from Sammobile and tested to see if I could get it back to 'warranty' condition, which was a success.
Confident that I could obtain warranty if I needed it, I re-rooted it, installed TB and greenify, and it ran sweetly for months from that point onwards.
I read about the arrival of updates (and knox) and concluded I didn't need them. It was working, leave it alone.
Then out of the blue, my nice stable machine broke. I didn't change anything I was aware of to cause it.
No normal boot.
No recovery.
Download only.
Using Odin, I tried allsorts, eventually getting the same Sammobile firmware to run.
2 days later, it broke again, same as before, but worse!?
Then I tried all sorts of stuff downloading no end of things trying to get it to boot or even go into recovery. The most promising approach was to reload the firmware along with a .pit file, but still no joy. I've lost track of the other things I tried, but I've been doing it for a week, so a lot has been done. In desperation, I even tried downloading the latest firmware, so I now have signs of knox of the odin page.
I now have the following symptoms:
Booting into recovery brings up the blue 'booting recovery' message then just blackness.
Normal boot is exactly the same as above.
Unpowered conection to my laptop gives a 5 second boot loop featuring the buzz only.
I can reliably boot into download and download stuff with Odin and change the little Odin page status messages. After (foolishly) trying the latest firmware, these messages say
ODIN MODE
PRODUCT NAME GT-I9505
CURRENT BINARY Samsung Official
SYSTEM STATUS Official
KNOX KERNEL LOCK 0x0
KNOX WARRANTY VOID 0x0
CSB-CONFIG-LSB 0x30
WRITE PROTECTION: enable
eMMC BURST MODE enabled
Please can anyone give me some advice on what else I could try?
Thanks
Steve

Wrinklespots said:
ODIN MODE
PRODUCT NAME GT-I9505
CURRENT BINARY Samsung Official
SYSTEM STATUS Official
KNOX KERNEL LOCK 0x0
KNOX WARRANTY VOID 0x0
CSB-CONFIG-LSB 0x30
WRITE PROTECTION: enable
eMMC BURST MODE enabled
Please can anyone give me some advice on what else I could try?
Thanks
Steve
Click to expand...
Click to collapse
If anything else is not working (especially, if you're unable to go to recovery) I'd call sammy service center. Your download mode says that you did not rooted your phone, and knox is untouched either.

spamtrash said:
If anything else is not working (especially, if you're unable to go to recovery) I'd call sammy service center. Your download mode says that you did not rooted your phone, and knox is untouched either.
Click to expand...
Click to collapse
Thanks for looking spamtrash.
I was wondering if I could get away with that. It does look good from the Odin display, but the flash counter must have a pretty high number in it by now! Won't that show up somewhere?
Do you think it does actually have a fault on it, rather than just some software that's messed up and needs tweaking?
Thanks
Steve

Wrinklespots said:
Thanks for looking spamtrash.
I was wondering if I could get away with that. It does look good from the Odin display, but the flash counter must have a pretty high number in it by now! Won't that show up somewhere?
Do you think it does actually have a fault on it, rather than just some software that's messed up and needs tweaking?
Thanks
Steve
Click to expand...
Click to collapse
1. Are you able to go to recovery mode?
2. Assuming that your previous communicates were taken from the screen in download mode - you're clean.
If answer for 1 is: NO, and assuming 2: do not bother the flash counter. Flash counter does not means you messed with custom ROMs, it just means amount of the ROM update tries. As they are unable to prove that the counter was not increased by failed KIES updates, you're safe.
To go deeper, service will have to flash and wipe your phone.
One thing: remove your sd card prior to giving/sending it out.

Try a different usb cable.I was in same boat as you (after stupidly thinking mobile odin pro liked modems).
Luckily I had an unused cable off my tab 3.

[Q] Odin fail, knox tripped, now can't do anything on the phone. help!

SOLVED:
Finally got Odin to work! Tried it on an actual PC laptop and not my vmware macbook. It failed at 99% the first time so tried another USB port and it went up and passed! this is on 4.4.2. I guess the main reason why the other firmwares would fail was because I originally tried to flash odin 4.4.2 but at this point I had no idea about knox and that you cannot go back in firmwares. So my last attempt was to push 4.4.2 after looking into the phones info saying it was on I337MVLUFNC1 bootloader. I was starting to think I had bricked this phone! sound works and calls working fine! whoop!
some history on the device:
- S4 was on Beanstalk 4.4.2, rooted.
- phone was starting to freeze up on this ROM so
- decided to go back to stalk Rogers rom via ODIN
- tried Odin v 3.09/v3.07/3.04 all failed
- tried different cables and two different computers. failed
- So then I decided to load TWRP back in from ODIN = Pass!, I get into recovery and load up a backup. This works but had NO sound or video playback and calls wont go through/freeze phone in call app.
- more tinkering, thinking it was maybe the Kernel/Modem. I download different Kernel/modm for the phone and sound still didnt work.
- Tried Firnware I337MVLUEMK6_I337MOYAEMK6_RWC, as well as the current I337MVLUAMG1_I337MOYAAMG1_RWC both were downloaded from sammobile.com
- tried kies and it cant connect to phone or does anything.
Phone errors:
-top corner of display shows:
Odin mode
product name: sgh-I337M
Current Binary: Samsung official
System status: Custom
Knox Kernel Lock: 0x0
Knox Warranty Void: 0x1
CBS - Config - LSB: 0x30
Write Protection: Enabled
eMMC Burst mode enabled
Currently:
- I can load TWRP anytime.
- I can also reload backups, install roms but sound, video, phone calls, mic dont work. some roms are super laggy as well.
- so phone is still useless atm.
ill try Odin again and copy the fail script.
it fails immediatly after system write.
iv searched knox trip, and some people have gotten stock firmware back on their device. but i have no way of doing so since odin fails horribly.. To my understanding if Knox has been tripped then you cannot downgrade firmware. but iv been trying to get 4.3 or even 4.4.2 on it and it fails.
actually i shouldnt say i tried to get 4.3 on it, because it seems i did get it on the phone at one point but then it had absolutly no signal. It would have signal for maybe 3 minutes then it drops it completely. tried APN settings and still wouldnt kick it. only thing I didnt try on that attempt was load up a different modem. which i should have.. but now cant even get that rom back on here as my sister deleted it..
any help would be appreciated.

Alright so im back on a backup from my other S4, running ok. signal is fine and wifi works. only thing is upon boot up i get:
- Unfortunately, Google Dialer has stopped.
- unfortunately, the process android.process.acore has stopped.
-unfortunately, the process android.process.meida has stopped.
i can hit ok many times but it keeps popping up.
so im still unable to do anything. i can still navigate through the phone but the pop ups come often.
UPDATE:
- Did a factory data reset within the phone and I dont get the pop ups anymore. but the Sound is still not working
one thing that's weird is when I use the app Phone Info the Sales Code (aka Region Code) is: ATT, but my working s4 with the same ROM says VMC under Region code? is this making my sisters phone not function properly? or maybe this is why I cannot flash stock rogers through odin because the phone is thinking its an ATT device and not a Rogers one?

Just wondering, since Knox is tripped am I able to still use Odin to flash to stock? Just want to clarify that before I waste more time with odin .
Iv tried rogers 4.2.2, 4.3 and pretty sure iv tried 4.4.2. But I'm going to download it and try that one again.
Phone was previously on 4.3 without signal. So I'm guessing that's the very least I can load up since Knox is tripped correct? I shouldn't have issues flashing Odin 4.4 stock rogers?
Just wondering why it fails once its writing to system..

Phone won't reboot after rooting (Samsung Galaxy J5)

Hello, um, I need a li'l help here
I just rooted my phone(Samsung J500H) and after it said "PASS" the phone is supposed to successfully restart but mine didn't. There are even yellowish-green lines on the screen. I used Odin(v.10) btw
I was about to try factory reset but I can't access recovery mode. Every time I try to it just goes back to the yellowish-green lines.
I can still access the download mode though. These are what's on the upper left of the screen:
Odin Mode
(Product Name)
Current Binary: Custom
System Status: Official
FRP Lock: Off
Knox Warranty Void: 0x1(4)
Secure Download: Enable
I downloaded Samsung Kies(I saw this tutorial on youtube on how he recovered his phone using Kies. There are a lot of comments saying it worked for them). It was fine until it asked for the s/n of my phone. I typed everything correctly and it would still end up saying "The S/N you have entered is incorrect". I even downloaded both Kies and Kies3 just to make sure and both has the same result.
That's it. After that I'm stuck. Heeeeellpp

scarystarrynight said:
Hello, um, I need a li'l help here
I just rooted my phone(Samsung J500H) and after it said "PASS" the phone is supposed to successfully restart but mine didn't. There are even yellowish-green lines on the screen. I used Odin(v.10) btw
I was about to try factory reset but I can't access recovery mode. Every time I try to it just goes back to the yellowish-green lines.
I can still access the download mode though. These are what's on the upper left of the screen:
Odin Mode
(Product Name)
Current Binary: Custom
System Status: Official
FRP Lock: Off
Knox Warranty Void: 0x1(4)
Secure Download: Enable
I downloaded Samsung Kies(I saw this tutorial on youtube on how he recovered his phone using Kies. There are a lot of comments saying it worked for them). It was fine until it asked for the s/n of my phone. I typed everything correctly and it would still end up saying "The S/N you have entered is incorrect". I even downloaded both Kies and Kies3 just to make sure and both has the same result.
That's it. After that I'm stuck. Heeeeellpp
Click to expand...
Click to collapse
Go to the link below and download the firmware for your phone and flash it via odin.
http://www.sammobile.com/firmwares/
http://updato.com/firmware-archive-select-model
You can also follow this guide to install firmware and rooting further if you want.
http://forum.xda-developers.com/galaxy-j5/how-to/tutorial-upgrade-j5-2015-to-6-0-t3443904

rjrulz007 said:
Go to the link below and download the firmware for your phone and flash it via odin.
http://www.sammobile.com/firmwares/
http://updato.com/firmware-archive-select-model
You can also follow this guide to install firmware and rooting further if you want.
http://forum.xda-developers.com/galaxy-j5/how-to/tutorial-upgrade-j5-2015-to-6-0-t3443904
Click to expand...
Click to collapse
I got a problem about the firmware though. I'm not quite sure which one...

scarystarrynight said:
I got a problem about the firmware though. I'm not quite sure which one...
Click to expand...
Click to collapse
On which firmware did u root? Lollipop or marshmallow? The greenish yellow screen is because u didnt flash the correct twrp recovery via odin...twrp for lollipop will not work on marshmallow
However if u need d link to the firmware, i ll send u as its there in my online files...download has unlimited bandwidth

scarystarrynight said:
I got a problem about the firmware though. I'm not quite sure which one...
Click to expand...
Click to collapse
Just download any country's firmware for J500H and flash it using odin. All country's firmware will work on your device as long as it is for J500H. Just dont use any other model's firmware like J500F.

scarystarrynight said:
Hello, um, I need a li'l help here
I just rooted my phone(Samsung J500H) and after it said "PASS" the phone is supposed to successfully restart but mine didn't. There are even yellowish-green lines on the screen. I used Odin(v.10) btw
I was about to try factory reset but I can't access recovery mode. Every time I try to it just goes back to the yellowish-green lines.
I can still access the download mode though. These are what's on the upper left of the screen:
Odin Mode
(Product Name)
Current Binary: Custom
System Status: Official
FRP Lock: Off
Knox Warranty Void: 0x1(4)
Secure Download: Enable
I downloaded Samsung Kies(I saw this tutorial on youtube on how he recovered his phone using Kies. There are a lot of comments saying it worked for them). It was fine until it asked for the s/n of my phone. I typed everything correctly and it would still end up saying "The S/N you have entered is incorrect". I even downloaded both Kies and Kies3 just to make sure and both has the same result.
That's it. After that I'm stuck. Heeeeellpp
Click to expand...
Click to collapse
i got the same problem... my phone showed that smart switch emergency thing but i was like "meh, let me reboot this" and received this, even if i charge this i see blue lines if i boot i see yellow lines and making the screen bright with green color, downloading these files tooks like 5 hours, like are you kidding me? so i think my phone is corrupted forever... does still has someone this problem and already fixed it?
UPDATE 2022.01.13
So i changed the rom to lineage os, firmware was absolutely mission imposibble for me, so i decided to change the rom, actually it works better tho.

any advice greatly appreciated

Hi there, I have a problem with my phone and I was ponited in the direction of this forum to see if anyone would be able to help out. Any assistance woud be very greatly appreciated
I am based in UK and I recently bought myself a Galaxy Note 4. 2nd Hand but as new condition. I tried to do an over the air software update to see if the phone would be able to get a more recent version of Android (it was running 5.0.1) and the phone wouldn't connect to the server. Also whe I tried to connect to Android Pay I got an error saying the device was rooted so I couldn't use the app on this phone. I therefore wanted to unroot the phone
I must stress my real technical knowledge of Android phones is basically at novice level but I tried to unroot the phone using SuperSU which I downloaded from the app store. I ran the unroot option and restarted the phone as prompted but this resulted in my phone being stuck in Bootloop. It wouldn't go past the Samsung load screen
I probably did the worst thing which was panic, went into recovery mode and attempted to factory reset to return the phone to out of box settings. I wiped the cache and did the factory reset but, of course, this hasn't resolved the problem. I then done a bit more reading and downloaded Odin and attempted to find the stock firmware for my phone (Model SM-910F), which i did, but unfortunately when I tried to flash this firmware back to my phone through Odin I get a failed error
So basically i'm on my knees trying to get some technical advice as to what else i can try or how to proceed. I did try taking it back to the Samsung Store and plead ignorance for help but the best I got there was that my main board would need replacing which would probably set me back another 200 nicker. For that money I may as well just buy a new phone. any help would be greatly appreciated as I'm currently left with a very expensive paperweight
Many thanks in advance guys
Lash

lashley82 said:
Hi there, I have a problem with my phone and I was ponited in the direction of this forum to see if anyone would be able to help out. Any assistance woud be very greatly appreciated
I am based in UK and I recently bought myself a Galaxy Note 4. 2nd Hand but as new condition. I tried to do an over the air software update to see if the phone would be able to get a more recent version of Android (it was running 5.0.1) and the phone wouldn't connect to the server. Also whe I tried to connect to Android Pay I got an error saying the device was rooted so I couldn't use the app on this phone. I therefore wanted to unroot the phone
I must stress my real technical knowledge of Android phones is basically at novice level but I tried to unroot the phone using SuperSU which I downloaded from the app store. I ran the unroot option and restarted the phone as prompted but this resulted in my phone being stuck in Bootloop. It wouldn't go past the Samsung load screen
I probably did the worst thing which was panic, went into recovery mode and attempted to factory reset to return the phone to out of box settings. I wiped the cache and did the factory reset but, of course, this hasn't resolved the problem. I then done a bit more reading and downloaded Odin and attempted to find the stock firmware for my phone (Model SM-910F), which i did, but unfortunately when I tried to flash this firmware back to my phone through Odin I get a failed error
So basically i'm on my knees trying to get some technical advice as to what else i can try or how to proceed. I did try taking it back to the Samsung Store and plead ignorance for help but the best I got there was that my main board would need replacing which would probably set me back another 200 nicker. For that money I may as well just buy a new phone. any help would be greatly appreciated as I'm currently left with a very expensive paperweight
Many thanks in advance guys
Lash
Click to expand...
Click to collapse
Go to odin download mode and tell me what exactly your model shows there? Maybe I can help.
Press 3 button combo while phone is turned off to go into download mode.(volume down+home+power)
Or even better if you can take picture and upload it while your phone in download mode.

Trex888 said:
Go to odin download mode and tell me what exactly your model shows there? Maybe I can help.
Press 3 button combo while phone is turned off to go into download mode.(volume down+home+power)
Or even better if you can take picture and upload it while your phone in download mode.
Click to expand...
Click to collapse
Hi and thank you for coming back to me, i get the following
ODIN MODE (HIGH SPEED)
Product Name: SM-910T - (this does confuse me slightly as the phone model actually says SM-910F)
Current Binary: Custom
System Status: Custom
Reactivation Lock: OFF
KNOX Warranty Void: 0x1 (3)
QUALCOMM Secureboot: ENABLE (CSB)
RP SWREV: S1, T1, R1, A2, P1
Secure Download: ENABLE
Hope this is of help

lashley82 said:
Hi and thank you for coming back to me, i get the following
ODIN MODE (HIGH SPEED)
Product Name: SM-910T - (this does confuse me slightly as the phone model actually says SM-910F)
Current Binary: Custom
System Status: Custom
Reactivation Lock: OFF
KNOX Warranty Void: 0x1 (3)
QUALCOMM Secureboot: ENABLE (CSB)
RP SWREV: S1, T1, R1, A2, P1
Secure Download: ENABLE
Hope this is of help
Click to expand...
Click to collapse
Hello there.
Sorry to say but you dont have N910f international model.its refurbished and faked by n910F software.as you can see your download mode shows n910t that's the orignal motherboard model.and also it shows binaries and status custom and not official as it should.also knox is 0×1 it means it was rooted before and warranty was void.
You have sm-N910T that's T-mobile usa model.
You can download latest N910T firmware from www.sammobiles.com/firmwares and flash through odin.
Dont try to flash n910f firmware otherwise it can be bricked and unusable.
Hope this will help.

Trex888 said:
Hello there.
Sorry to say but you dont have N910f international model.its refurbished and faked by n910F software.as you can see your download mode shows n910t that's the orignal motherboard model.and also it shows binaries and status custom and not official as it should.also knox is 0×1 it means it was rooted before and warranty was void.
You have sm-N910T that's T-mobile usa model.
You can download latest N910T firmware from and flash through odin.
Dont try to flash n910f firmware otherwise it can be bricked and unusable.
Hope this will help.
Click to expand...
Click to collapse
Thank you, I'm going to give this a go and see if it works
Many Thanks

lashley82 said:
Thank you, I'm going to give this a go and see if it works
Many Thanks
Click to expand...
Click to collapse
You're welcome.
Make sure after flash firmware go to recovery by pressing (volume up+ home+ power ) while phone is off and do (data factory reset & wipe cache)otherwise it will stuck on Samsung logo at first boot.
First boot will take approximately 15 minutes.

help please!!!!

I have a s7 edge I got through sprint. I flashed smg935u firmware, a couple weeks later, took it to cell store to have them unlock it, and they did. custom with unlocked symbol. I had problems with texting, couldn't change apn settings, so they told me to flash back to the sprint firmware. I was on smg935u android 7.0, and my dumb ass wasn't paying any attention and tried flashing to smg935p android 6.1. so now my phone is soft bricked and stuck in a bootloop. someone please help me. what can I do? I have tried various firmwares with both odin 3 12 3 and odin princecomsy. this is pretty much the extent of my knowledge. someone please help me get this working again. I keep getting the sw rev check fail abort fused 4 binary 2 and its hard to even get into download mode. I can not get into bootloader mode at all.
odin mode high speed
product name smg935u
current binary Samsung official
system status custom
fap lock off
warranty void 0x0
qualcome secure boot enable
rp swrev b4(2,1,1,1,1) k1 s3

Shanedavid30 said:
I have a s7 edge I got through sprint. I flashed smg935u firmware, a couple weeks later, took it to cell store to have them unlock it, and they did. custom with unlocked symbol. I had problems with texting, couldn't change apn settings, so they told me to flash back to the sprint firmware. I was on smg935u android 7.0, and my dumb ass wasn't paying any attention and tried flashing to smg935p android 6.1. so now my phone is soft bricked and stuck in a bootloop. someone please help me. what can I do? I have tried various firmwares with both odin 3 12 3 and odin princecomsy. this is pretty much the extent of my knowledge. someone please help me get this working again. I keep getting the sw rev check fail abort fused 4 binary 2 and its hard to even get into download mode. I can not get into bootloader mode at all.
odin mode high speed
product name smg935u
current binary Samsung official
system status custom
fap lock off
warranty void 0x0
qualcome secure boot enable
rp swrev b4(2,1,1,1,1) k1 s3
Click to expand...
Click to collapse
I know sometimes if you let the battery go dead then after charge boot into bootloader, make sure you got a good tar file for your stock phone it may be a bad tar file if you are getting errors.

Hmmmm sounds like you accidentally flashed very old 6.0.1 firmware back when it bootloader version 2 (which they eventually updated to version 4 so you can't go backwards) so I would just completely charge the phone and go into recovery and do a facorty reset then try flashing the latest Sprint 7.0 firmware and you should be good