Stuck in Recovery Boot Loop after Rooting... - Galaxy Note 3 Q&A, Help & Troubleshooting

I'm using the Canadian version of the Galaxy Note 3: SM-N900W8. I was rooted and used Kingo to unroot and updated my firmware to Kitkat 4.4.2.
I then successfully rooted with Kingo but it then went into the Recovery Boot loop. ( Displays on top left of screen).
I removed battery but it returns to the boot loop. Been reading up on some steps. I'm trying to flash a stock ROM via Odin. How can I put my phone into download mode when it will not respond to hitting the three buttons. Vol down + Home + Power. Also which version of Rom is needed. Please advise how to recover my phone from this state. I do not have much experience with this hence my post for help.
Any help will be greatly appreciated.
Cheers.

Goliathius said:
I'm using the Canadian version of the Galaxy Note 3: SM-N900W8. I was rooted and used Kingo to unroot and updated my firmware to Kitkat 4.4.2.
I then successfully rooted with Kingo but it then went into the Recovery Boot loop. ( Displays on top left of screen).
I removed battery but it returns to the boot loop. Been reading up on some steps. I'm trying to flash a stock ROM via Odin. How can I put my phone into download mode when it will not respond to hitting the three buttons. Vol down + Home + Power. Also which version of Rom is needed. Please advise how to recover my phone from this state. I do not have much experience with this hence my post for help.
Any help will be greatly appreciated.
Cheers.
Click to expand...
Click to collapse
having the exact same problem. Help?

alquistador said:
having the exact same problem. Help?
Click to expand...
Click to collapse
Aluistador
I managed to get my phone back up and running. This is what I did. Inserted my battery and pressed the following buttons in this order.
Press and hold Home + Power + Volume Down buttons but instead of pushing Vol Up button I chose Vol Down instead to restart phone.
This rebooted my phone which is now up and running. Give it a shot and see if it works for you.
Post back if it does. Good luck.

Goliathius said:
Aluistador
I managed to get my phone back up and running. This is what I did. Inserted my battery and pressed the following buttons in this order.
Press and hold Home + Power + Volume Down buttons but instead of pushing Vol Up button I chose Vol Down instead to restart phone.
This rebooted my phone which is now up and running. Give it a shot and see if it works for you.
Post back if it does. Good luck.
Click to expand...
Click to collapse
i odin twrp and it appears everything is operating fine. i tried the chain fire cf auto root and that also give me a fail. no root for me.

alquistador said:
i odin twrp and it appears everything is operating fine. i tried the chain fire cf auto root and that also give me a fail. no root for me.
Click to expand...
Click to collapse
It appears that my root also did not go through even though it said root successful with Kingo. I guess the boot loop messed it up. I'm going to keep it here fir now as I need my phone tomorrow. Might give the root another shot another time. Just happy I was able to bring it back into operation. I'm glad you got your back as well.
Cheers!!

Related

[Q] {PLEASE HELP!!!} Bricked Verizon Note 3

I rooted my phone successfully with vRoot but I wanted KitKat on my phone, so I went through SafeStrap to install the update and when I rebooted the phone, it just is black once I boot into system. I can still boot into download and recovery mode but that's it. Please help!!! My Note 3 is through Verizon and has the MJE update. I am in the hospital with my Fiance who is pregnant (they induced her today and have been here for 12 hours now) and really need my phone to post updates to family members. What do I do?!?
codestermyre said:
I rooted my phone successfully with vRoot but I wanted KitKat on my phone, so I went through SafeStrap to install the update and when I rebooted the phone, it just is black once I boot into system. I can still boot into download and recovery mode but that's it. Please help!!! My Note 3 is through Verizon and has the MJE update. I am in the hospital with my Fiance who is pregnant (they induced her today and have been here for 12 hours now) and really need my phone to post updates to family members. What do I do?!?
Click to expand...
Click to collapse
If you can get to your computer you will have to Odin back to stock and then re-root. Files and directions for this are here . If not by a computer you can try to boot into recovery mode by holding the volume up+home and the power button. Then scroll down to clear cache and then factory reset with the volume keys. This might get you back to stock, if not Odin.
Misterxtc said:
If you can get to your computer you will have to Odin back to stock and then re-root. Files and directions for this are here . If not by a computer you can try to boot into recovery mode by holding the volume up+home and the power button. Then scroll down to clear cache and then factory reset with the volume keys. This might get you back to stock, if not Odin.
Click to expand...
Click to collapse
Well the clear cache and factory reset didn't work, still at a black screen. But I am downloading the other thing. Thank you for the quick response. I will let you know how that turns out.
Misterxtc said:
If you can get to your computer you will have to Odin back to stock and then re-root. Files and directions for this are here . If not by a computer you can try to boot into recovery mode by holding the volume up+home and the power button. Then scroll down to clear cache and then factory reset with the volume keys. This might get you back to stock, if not Odin.
Click to expand...
Click to collapse
Odin wont see the phone. What should I do???
codestermyre said:
Odin wont see the phone. What should I do???
Click to expand...
Click to collapse
Seems like you don't have the Samsung USB drivers installed.
http://forum.xda-developers.com/showthread.php?t=2576104
That thread has a link to get them, I believe. Make sure you follow directions, I think you tried flashing a rom that was intended for the developer edition of the note 3, which is what caused your brick.

Rooted via Kingo - Phone boot loops into recovery mode. Unresponsive.

Recently attempted to root via Kingo after backing up date with Kies.
Upon completion of what appeared to be a successful process, phone began rebooting continuously into recovery mode, powering down and then repeating. Attempts to boot into recovery mode (Vol up, home, power) fail as phone is unresponsive. I'd really like to hope there's a way around this.
Repeat: Phone is unresponsive to key press and does not boot long enough to recognize via USB on PC.
yamabin said:
Recently attempted to root via Kingo after backing up date with Kies.
Upon completion of what appeared to be a successful process, phone began rebooting continuously into recovery mode, powering down and then repeating. Attempts to boot into recovery mode (Vol up, home, power) fail as phone is unresponsive. I'd really like to hope there's a way around this.
Repeat: Phone is unresponsive to key press and does not boot long enough to recognize via USB on PC.
Click to expand...
Click to collapse
Pull battery, put back in and boot to download mode. re-flash stock rom then flash cf-autoroot (make sure it's the right one for your version of Android).
Don't use Kingo app again...
ultramag69 said:
Pull battery, put back in and boot to download mode. re-flash stock rom then flash cf-autoroot (make sure it's the right one for your version of Android).
Don't use Kingo app again...
Click to expand...
Click to collapse
Thanks for the zippy reply.
Finally broke the boot loop. waiting for the stock rom to download while phone sits in downloading mode.
Kingo is now banished from harddrive
yamabin said:
Thanks for the zippy reply.
Finally broke the boot loop. waiting for the stock rom to download while phone sits in downloading mode.
Kingo is now banished from harddrive
Click to expand...
Click to collapse
don't let it sit in download mode too long - you need power to flash...
same situation, unable to root
ultramag69 said:
don't let it sit in download mode too long - you need power to flash...
Click to expand...
Click to collapse
I had the same problem, boot loop from logo as the phone kept on trying to go to recovery mode
I fix this by going to download mode ( vol down + power, and vol down again to reboot)
my problem is I can't seem to root my phone with any method so far, I keep on getting stuck in boot loop when the phone tries to go in recovery mode
any help would be appreciated
it's a note 3, N9006 ( Chinese), kit kat 4.4.2
goukison said:
I had the same problem, boot loop from logo as the phone kept on trying to go to recovery mode
I fix this by going to download mode ( vol down + power, and vol down again to reboot)
my problem is I can't seem to root my phone with any method so far, I keep on getting stuck in boot loop when the phone tries to go in recovery mode
any help would be appreciated
it's a note 3, N9006 ( Chinese), kit kat 4.4.2
Click to expand...
Click to collapse
No Root Methods for KK
Had the same problem. This thread may help keeping to keep root on 4.4.2
user_null said:
Had the same problem. This thread may help keeping to keep root on 4.4.2
Click to expand...
Click to collapse
Tks for tip

[Q] I bricked my Verizon S5. Any help appreciated.

I tried to upgrade to the latest version via Keis on my rooted S5. After it said it was successful, it rebooted and now it freezes on the verizon screen when it loads and goes no further. I tried to reset the phone by using Odin 3.09 and the original stock kernal G900V_NCG_Stock_Kernel.tar.md5 but it will just stay at the "samsung unlocked" screen, reboot, then goes into recovery mode. I have done a factory reset on it and re-tried the upgrade with no luck. It will only boot into the recovery mode automatically (I don't have to press anything, it just goes strait to it when it boots). Any advice?
Thank you,
pubert0 said:
I tried to upgrade to the latest version via Keis on my rooted S5. After it said it was successful, it rebooted and now it freezes on the verizon screen when it loads and goes no further. I tried to reset the phone by using Odin 3.09 and the original stock kernal G900V_NCG_Stock_Kernel.tar.md5 but it will just stay at the "samsung unlocked" screen, reboot, then goes into recovery mode. I have done a factory reset on it and re-tried the upgrade with no luck. It will only boot into the recovery mode automatically (I don't have to press anything, it just goes strait to it when it boots). Any advice?
Thank you,
Click to expand...
Click to collapse
Try this:
1 wipe data/factory reset in recovery
2 remove battery when done
3 start odin, load lollipop firmware, do not connect phone
4 hold volume down, home button and power. do not insert battery
5 insert battery, while holding volume down, home button and power
6 it should boot to download mode
7 now connect to pc
8 flash verizon lollipop in odin
lingowistico said:
Try this:
1 wipe data/factory reset in recovery
2 remove battery when done
3 start odin, load lollipop firmware, do not connect phone
4 hold volume down, home button and power. do not insert battery
5 insert battery, while holding volume down, home button and power
6 it should boot to download mode
7 now connect to pc
8 flash verizon lollipop in odin
Click to expand...
Click to collapse
I was able to finally get it working by following the directions here:
http://forum.xda-developers.com/showthread.php?t=2784880
I did try your way but it still gave me the same error. I think something got f'd up on the partitioning? I'm not sure, but i loaded it into Odin and it kept on failing. Only after I re-partitioned it, it finally came back. Thank you though for your help.
pubert0 said:
I was able to finally get it working by following the directions here:
http://forum.xda-developers.com/showthread.php?t=2784880
I did try your way but it still gave me the same error. I think something got f'd up on the partitioning? I'm not sure, but i loaded it into Odin and it kept on failing. Only after I re-partitioned it, it finally came back. Thank you though for your help.
Click to expand...
Click to collapse
Glad it worked out and thanks for telling how you solved it.

Recovery Is Not Seandroid Enforcing

I tried to root my phone S7 Edge 6.1.1 just a moment ago using ODIN and CF Auto Root. I got the PASSES! sign in ODIN but upon phone rebooting I am stuck on the Samsung S7 Edge logo screen with text in red 'Recovery Is Not Seandroid Enforcing" up the top.
At this time I am unable to turn my phone off, when I do it just turns back on and goes to the same screen. I can't get into download or recovery mode either.
Any help on how to fix would by greatly appreciated.
Thanks in advance.
Also thought I should add, my phone doesn't get registered when I connect it to my PC either, it wont show up in ODIN so I am unable to flash a stock recovery at this time.
It's trying to boot into recovery.
When you say you rooted with CF Auto Root, what did you do precisely? And did you follow Chainfire's specific instructions regarding the lack of screen output during the process?
Beefheart said:
It's trying to boot into recovery.
When you say you rooted with CF Auto Root, what did you do precisely? And did you follow Chainfire's specific instructions regarding the lack of screen output during the process?
Click to expand...
Click to collapse
Thanks for the reply.
I used CF-Auto-Root-zerolte-zeroltexx-smg925f.tar to root.
The steps I used was to simply put my phone into download mode and use ODIN to flash the file mentioned above. That is as far as I got unfortunately. I did this once before, a few month back when I first got the phone with no issues. I remember having to install TWRP but I couldn't remember if I did that pre-root or post-root. But I think that is where I went wrong.
Now I am unable to do anything with my phone. I can't turn it off, get into download or recovery mode. When I hold down VOL UP+POWER+HOME it just resets the phone back to the samsung logo screen.
Any ideas on what I could do?
You used the CF Auto Root file for an S6 Edge.
Beefheart said:
You used the CF Auto Root file for an S6 Edge.
Click to expand...
Click to collapse
OH GOD. You're right. I just realized that. I was supposed to have them saved into their own folders but I guess I saved that one too the wrong folder.
So what does that mean for the life of my phone then? Is it toast or is it recoverable somehow?
What is your model? Is it the SM-G935F? If so, first things first, download the correct CF Auto Root file for your device (here) and try again. Press VOL DOWN+POWER+HOME and it should reboot into Download Mode. Then try to flash the correct file in Odin again.
These phones are very difficult to hard brick, especially with something like CF Auto Root so you should be ok.
Beefheart said:
What is your model? Is it the SM-G935F? If so, first things first, download the correct CF Auto Root file for your device (here) and try again. Press VOL DOWN+POWER+HOME and it should reboot into Download Mode. Then try to flash the correct file in Odin again.
These phones are very difficult to hard brick, especially with something like CF Auto Root so you should be ok.
Click to expand...
Click to collapse
Thanks.
Yes, it is a SM-G935F. Unfortunately I am unable to reboot the phone into Download Mode. When pressing VOL DOWN+POWER+HOME it just takes me straight back to the Samsung logo where it says "Recovery Is Not Seandroid Enforcing". I'm hoping that once the battery drains completely I will be able to boot into Download Mode again.
Try simply resetting it instead. Press volume down and the power key (don't press home) for around 7-10 seconds. Once it starts to reset, remove your fingers from the buttons very briefly then press volume down, home and power to enter download mode.
Beefheart said:
Try simply resetting it instead. Press volume down and the power key (don't press home) for around 7-10 seconds. Once it starts to reset, remove your fingers from the buttons very briefly then press volume down, home and power to enter download mode.
Click to expand...
Click to collapse
That hasn't worked either unfortunately.
I just found this thread from a guy having a similar problem. He just had to wait for his phone's battery to drain completely and then he was able to enter download mode again.
You shouldn't have to though. If you can get the phone to reset at all (even if it's to make another attempt to go into recovery) then providing you time it right, you should be able to get into download mode. Did keeping your fingers on just the volume down and power buttons do anything? Keep them on continuously for up to 20 seconds and see what happens. Did you say pressing vol up & home & power made it reset and try to again get into recovery? What happens if, as soon as the screen indicated it's resetting, you remove your fingers and quickly press vol down & home & power instead?
Anyway, even if you have to wait until the phone dies, getting into download will be possible eventually. Then worst case scenario would be you having to reflash stock back. Or, as would be my preference, flash TWRP then flash a custom rom zip like Superman.
Just to confirm, I take it you selected OEM Unlock in dev options?
Beefheart said:
You shouldn't have to though. If you can get the phone to reset at all (even if it's to make another attempt to go into recovery) then providing you time it right, you should be able to get into download mode. Did keeping your fingers on just the volume down and power buttons do anything? Keep them on continuously for up to 20 seconds and see what happens. Did you say pressing vol up & home & power made it reset and try to again get into recovery? What happens if, as soon as the screen indicated it's resetting, you remove your fingers and quickly press vol down & home & power instead?
Anyway, even if you have to wait until the phone dies, getting into download will be possible eventually. Then worst case scenario would be you having to reflash stock back. Or, as would be my preference, flash TWRP then flash a custom rom zip like Superman.
Just to confirm, I take it you selected OEM Unlock in dev options?
Click to expand...
Click to collapse
I have never had any trouble getting into recovery or download before so I know the method. But just the properly clarify for you I will explain some of the combination I have tried without success. Bare in mind the phone is constantly turned on and idles on the Samsung logo.
I have tried:
Hold VOL DOWN+POWER+HOME, the phone resets and goes back to the logo.
Hold VOL DOWN+POWER, same as above.
Hold VOL UP+POWER+HOME, nothing happens at all.
Hold VOL UP+POWER, same as above.
Hold VOL DOWN+POWER+HOME, release and repress all on black screen, just goes back to logo.
Hold VOL DOWN+POWER, release and hold VOL DOWN+POWER+HOME on black screen, just goes back to logo.
and numerous other things like random combination to try and enter Download or Recovery mode, which have all failed.
Right now it's just stuck on the Samsung logo and staying there, taking forever to drain battery. I work in the morning so hopefully it is dead by then and I can get into Download mode.
Have already started download stock firmware in hopes that I will be able to flash it after.
Thanks a bunch for your help. If you think of anything else I might be able to try let me know!
Oh wow. 100+ attempts and I followed your last post about holding for up to 20 seconds. I was waiting ~5 seconds and releasing thinking that it hadn't worked.
Finally go into Download mode and will flash stock firmware and let you know how I go.
Thanks again! I owe you a cold one.
EDIT: Was no need to flash stock firmware. Just flashed the proper version of CF Auto Root and it worked. Again, thank you so much!
Fantastic. Hope you get it sorted.
On a side note, you have probably already tripped knox and you will have lost you OS data and possibly even what you have stored on internal storage. If so, I suggest you install TWRP, format data (you will lose everything with this but it removed encryption) and install a custom rom like Superman 1.9 from your external SD. It's better than plain stock and comes pre-rooted with plenty of other mods.
I can't get it to work? What keys did you held down?
This is how my screen looks
cs5-2.4pda.to/7951347.jpg (copy this link in browser)
I tried to root with Odin but I think I might have failed. How can I undo this?
recovery is not seandroid enforcing
hello,
my S7 Edge was rooted with cf-auto-root and worked fine but after 2 monthe I've installed LBE_Security_Rel_6.1.1928_A1_DE_v5_signed and reconized the message device is not tooted.
I was not very clever and cofirmed the question "fix the root problem" I don't remember exactly the words. After that root was gone.
I've flashed the stock Fw G935FXXU1APD1_G935FDRE1APC3_DRE but I still have the message "recovery is not seandroid enforcing" after trying to root with CF auto root.
AP:G935FXXU1APD1
CP:G935FXXU1APD1
CSC:G935FDRE1APC3
Is there any way to get root again
Any help on how to fix would by greatly appreciated.
Thanks in advance.
doodlemeat said:
I can't get it to work? What keys did you held down?
This is how my screen looks
cs5-2.4pda.to/7951347.jpg (copy this link in browser)
I tried to root with Odin but I think I might have failed. How can I undo this?
Click to expand...
Click to collapse
Simply hold down Home + Power + Volume Down for 10-15 seconds - don't release when the phone initially reboots and gives the same error, keep them held down and download mode will appear. I have to hold for 11 seconds, a strangely unrounded number.
Hello Guys I have this Same issue Yesterday....... This happens when you flash outdated CF Autoroot. CF Autoroot Updated on 25/08/2016... Download it...
Fix for Stuck in Logo Screen
Just Click and Hold ...... Vol Down + Menu + Power Keys ...... DO NOT RELEASE. IT Will Restart. DONT release. It will restart again and you will be download mode.
i found this during the rooting process. its a bit different to older samsungs on the s7 / s7edge. YOU HAVE TO KEEP HOLD OF VOL DOWN + HOME + POWER until it enters download mode, which can be 20-25 seconds

Please help!

Hello everyone, from the title you've probably figured that I might be a noob and you'd be correct.
I have absolutely no idea what I'm doing. I'm trying to root and add TWRP to my phone, I've searched for a user friendly guide and this: "https://rootthedroid.com/root-leeco-le-max-2-install-twrp-recovery/" is the most user friendly guide I can find.
Something is not installing correctly and I think there are gaps in this guide, I'm pretty good at reading and following directions. I'm able to get into bootloader and Once I think I've installed TWRP the power button + volume down button does nothing when the phone is on except for take a screen shot and eventually shut down. However, when the phone is powered down, I'm able to hold the volume down + power buttons and it will eventually take me back to the bootloader screen but not to TWRP as the guide states it should.
So after this I thought I did something wrong and went to factory reset the phone.... When I initiated factory reset, that brought up the TWRP menu, so it was in fact installed onto the phone. I then continue the instructions in the guide. At the end, the power down + power button function does not work except for powering down the phone and bringing me back to the bootloader screen. I then installed the TWRP app and it still says that the device is not rooted.
I'm hoping someone can point me in the direction of a good thorough guide or please explain to me step by step how to get this thing rooted. I have x829 version and will be using primarily in Ohio if that matters. I'd also like some guidance on what ROM to choose.
Thank you for your time!!!!
boboyt said:
Hello everyone, from the title you've probably figured that I might be a noob and you'd be correct.
I have absolutely no idea what I'm doing. I'm trying to root and add TWRP to my phone, I've searched for a user friendly guide and this: "https://rootthedroid.com/root-leeco-le-max-2-install-twrp-recovery/" is the most user friendly guide I can find.
Something is not installing correctly and I think there are gaps in this guide, I'm pretty good at reading and following directions. I'm able to get into bootloader and Once I think I've installed TWRP the power button + volume down button does nothing when the phone is on except for take a screen shot and eventually shut down. However, when the phone is powered down, I'm able to hold the volume down + power buttons and it will eventually take me back to the bootloader screen but not to TWRP as the guide states it should.
So after this I thought I did something wrong and went to factory reset the phone.... When I initiated factory reset, that brought up the TWRP menu, so it was in fact installed onto the phone. I then continue the instructions in the guide. At the end, the power down + power button function does not work except for powering down the phone and bringing me back to the bootloader screen. I then installed the TWRP app and it still says that the device is not rooted.
I'm hoping someone can point me in the direction of a good thorough guide or please explain to me step by step how to get this thing rooted. I have x829 version and will be using primarily in Ohio if that matters. I'd also like some guidance on what ROM to choose.
Thank you for your time!!!!
Click to expand...
Click to collapse
You need to go for the right combination brother.....
Volume down with power button will take you to bootloader.....
For TWRP, press Volume up and power button simultaneously......
And for rooting flash magisk and you're good to go.....
Ahmad04 said:
You need to go for the right combination brother.....
Volume down with power button will take you to bootloader.....
For TWRP, press Volume up and power button simultaneously......
And for rooting flash magisk and you're good to go.....
Click to expand...
Click to collapse
This guy's got the right answer.
Please be sure to continue holding power and volume up until the words "recovery" come up on the screen otherwise it will just do a normal boot to Android.
Another method is to enable developer options (about phone and tap build 7 times), then to enable ADB, then use a PC and usb to the phone and use adb reboot recovery.
Also, if it boots to EUI ROM recovery instead of TWRP? It could be EUI ROM overwriting TWRP after flashing via fastboot.
The solution to that issue is to reboot into bootloader, flash recovery TWRP and then to either hold power and volume up to reboot into recovery or to use "fastboot boot TWRP.img" and then do reboot into recovery from there.
Why do we need to flash magisk?
kkcheong said:
Why do we need to flash magisk?
Click to expand...
Click to collapse
If you need root access.....
Ahmad04 said:
If you need root access.....
Click to expand...
Click to collapse
I root without magisk.

Categories

Resources