[Q] Defy+ unlocks while talking - Defy Q&A, Help & Troubleshooting

hi, couldn't find anything similar via search and it seems that I'm the only one having such problem.
so, I've tried numerous roms by Quarx, few slimkats and my phone regularly unlocks (i assume) while talking, and hangs up, or even worse, tries to call someone else. i was ready to call it a proximity sensor malfunction, but if i try to cover it while holding phone in hand it works perfectly every time, and I'm using stock ROM for a few weeks now - no hang ups at all. only solution is to push phone firmly into my face or keep it away from it..
so, any suggestions ? even an app which wouldn't unlock the phone in call unless unlock button is pressed or call just ended would be very nice.
thanks.

Related

Screen Lock issue with HD2

After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers

HD2 in-call lock needed (capacitive screen is too sensitive)

I've been using my HD2 since its release, so i can tell you i've gotten used to all sorts of habits in order to prevent accidental "touches" with either my cheek or my pocket when using a BT headset.
Yet, i still get them. Very often i manually lock the phone during calls, but not always.
I've tried smartlock to lock the phone automatically during calls. It works to some extent, but not always. The phone unlocks twice during call from BT headset, when dialing and when connected. Smartlock will very often fail to lock the phone the second time, locking incoming calls doesn't always work either (i'm guessing it's conflicting with the proximity sensor). Plus since the lock screen during calls is different, a slight rub in the middle of the screen will unlock it (no need to slide anything).
This issue was so bad that i found a way to override the in-call lockscreen with the regular slide-to-unlock lockscreen.
Anyway, after all these months i realized that the only times i completly trust my phone during calls is when i'm holding it in my hand or it's laying on the table while i talk.
I'm posting this to check if any of you found better solutions to this problem than what i mentioned.
Cheers
depending on the rom you are on, try using two fingers to tap the caller id pic, it locks the screen on later roms, then hard key to unlock.(but not end key, cos that still hangs up)
wingm4n said:
I've been using my HD2 since its release, so i can tell you i've gotten used to all sorts of habits in order to prevent accidental "touches" with either my cheek or my pocket when using a BT headset.
Yet, i still get them. Very often i manually lock the phone during calls, but not always.
I've tried smartlock to lock the phone automatically during calls. It works to some extent, but not always. The phone unlocks twice during call from BT headset, when dialing and when connected. Smartlock will very often fail to lock the phone the second time, locking incoming calls doesn't always work either (i'm guessing it's conflicting with the proximity sensor). Plus since the lock screen during calls is different, a slight rub in the middle of the screen will unlock it (no need to slide anything).
This issue was so bad that i found a way to override the in-call lockscreen with the regular slide-to-unlock lockscreen.
Anyway, after all these months i realized that the only times i completly trust my phone during calls is when i'm holding it in my hand or it's laying on the table while i talk.
I'm posting this to check if any of you found better solutions to this problem than what i mentioned.
Cheers
Click to expand...
Click to collapse
might want to check out s2u2. It is very good at locking the phone in call.
http://s2u2.ac-s2.com/
Hello, same thing happened to me, change to the 1.66 ROM and the problem was solved, maybe help you.
wingm4n said:
I've been using my HD2 since its release, so i can tell you i've gotten used to all sorts of habits in order to prevent accidental "touches" with either my cheek or my pocket when using a BT headset.
Yet, i still get them. Very often i manually lock the phone during calls, but not always.
I've tried smartlock to lock the phone automatically during calls. It works to some extent, but not always. The phone unlocks twice during call from BT headset, when dialing and when connected. Smartlock will very often fail to lock the phone the second time, locking incoming calls doesn't always work either (i'm guessing it's conflicting with the proximity sensor). Plus since the lock screen during calls is different, a slight rub in the middle of the screen will unlock it (no need to slide anything).
This issue was so bad that i found a way to override the in-call lockscreen with the regular slide-to-unlock lockscreen.
Anyway, after all these months i realized that the only times i completly trust my phone during calls is when i'm holding it in my hand or it's laying on the table while i talk.
I'm posting this to check if any of you found better solutions to this problem than what i mentioned.
Cheers
Click to expand...
Click to collapse
Try PocketShield
http://www.pocketshield.net/

WP7 End Call Issue

Hi Guys,
I have been having issues when trying to end a call with the new WP7 Rom. I also used to have this when using Andriod Roms.
When I go to end a call, pressing the end call button does nothing apart from light up the keypad. I've tried pressing every button but nothing but the keypad lighting up happens, the call never ends! I have to remove my battery and switch the phone back on to get the use of my phone back.
I have :
HardSPL 2.08
MAGDLR111
Radio 2.15.50.14
Any Ideas?
Thanks,
Jon
jonathan.stowell said:
Hi Guys,
I have been having issues when trying to end a call with the new WP7 Rom. I also used to have this when using Andriod Roms.
When I go to end a call, pressing the end call button does nothing apart from light up the keypad. I've tried pressing every button but nothing but the keypad lighting up happens, the call never ends! I have to remove my battery and switch the phone back on to get the use of my phone back.
I have :
HardSPL 2.08
MAGDLR111
Radio 2.15.50.14
Any Ideas?
Thanks,
Jon
Click to expand...
Click to collapse
Did you not try the end call on the screen? Not the hard one on the bottom right of phone
Russ
The screen turns off when making a call so the touch buttons are not available. This is why I have to remove the battery as I have no other way of bringing the display back to life. Obviously if I make a call and the other person hangs up it's fine. However if they do not answer and it goes to voicemail or I call my voicemail I get stuck in a never ending loop of press 2 to hear your messages.
jonathan.stowell said:
The screen turns off when making a call so the touch buttons are not available. This is why I have to remove the battery as I have no other way of bringing the display back to life. Obviously if I make a call and the other person hangs up it's fine. However if they do not answer and it goes to voicemail or I call my voicemail I get stuck in a never ending loop of press 2 to hear your messages.
Click to expand...
Click to collapse
Official windows phones have no hard end call button, just the on screen one, therefor I dont think its possible to end a call with the hardware button. Yes, the screen goes off when making a call, but due to the proximity censor it should come back when you move it away from your head. If it does not, make sure its not covered, even a screen protector can block the proximity sensor. Its located next to the speaker.
Hmm I removed the screen protector and still no joy when I move the phone away from my face. The screen just remains black. I did crack the screen about 5 months ago and had it replaced, perhaps they've done a poor job on this....
Don't think so... My is in perfect shape. proximity works on android but not on wp7... i also can't press end call button.
same thing with me
well i get the same problem with mine also, is there anything we can do for that.
I have the same issue, though it only happens to me when calling my voicemail. I hit "end call" and it just hangs there with the message "Ending call..." and I have to pull the battery :/ Regular phone calls have been just fine though.
Finally cracked this one!
I have been experiencing this issue on my Optimus 7 phone since day one, on all firmware versions and I now have the latest update.
This is what worked for me:
-set the automatic brightness to off and choose any manual setting that suits your needs, I chose medium.
-set the screen timeout to never (not sure that this is necessary, I will change it back to 30 sec to see if the issue returns and post back)
I hope this works with your phones, it was really frustrating to pull the batery out. Good luck!
I've had this issue as well. Pressing the end call button on the screen won't end many of my calls, voicemail or to another person. But it's rare enough that it hasn't bothered me, too much. But is a problem that needs to be figured out, if possible.
We should come up witha way to re map the hard buttons to usefull use
jonathan.stowell said:
Hi Guys,
I have been having issues when trying to end a call with the new WP7 Rom. I also used to have this when using Andriod Roms.
When I go to end a call, pressing the end call button does nothing apart from light up the keypad. I've tried pressing every button but nothing but the keypad lighting up happens, the call never ends! I have to remove my battery and switch the phone back on to get the use of my phone back.
I have :
HardSPL 2.08
MAGDLR111
Radio 2.15.50.14
Any Ideas?
Thanks,
Jon
Click to expand...
Click to collapse
I'm assuming your phone is an HD2. First of all, the call should automatically end when the other party hangs up. Secondly, just hit the Power button to turn the screen back on and then unlock the phone and hang up. What is so difficult? WP7 remaps the HD2 buttons so they don't work as they did in WM.
swangoose said:
I have been experiencing this issue on my Optimus 7 phone since day one, on all firmware versions and I now have the latest update.
This is what worked for me:
-set the automatic brightness to off and choose any manual setting that suits your needs, I chose medium.
-set the screen timeout to never (not sure that this is necessary, I will change it back to 30 sec to see if the issue returns and post back)
I hope this works with your phones, it was really frustrating to pull the batery out. Good luck!
Click to expand...
Click to collapse
Worked. T H A N K S!!!

[Q] Home button wont work During Call.

I have searched and then made this thread. There were some people with home button issue but None of those were related to my problem.
PHONE MODEL - GT-I9505 ( International version)
I have had my S4 for a couple of months now and I am addicted to flashing. I flash a test lot of new roms.
MY PROBLEM
When i make or I get a call, Once i pick the call and put my phone to the ear and after the proximity sensor turns off the screen i cannot use my home button or powerbutton to wake the screen during call. For example if i want to cut the call During a call. I simply cannot do it. Sometimes the home button will respond, Some times it wont
For the home button to work The other party has to cut the all only when my phone detects that the call has been disconnected it wakes up. Looks like the home button stops functioning ?
I dont know what is happening.
I thought it was the rom issue, But it isnt. I tried two different roms. Did the same behaviour.
Any advice or anything to help me will be appreciated. Is my hardware damaged?
My phone is never dropped and is very new like .
ROMS I TRIED
Wanam Lite.
Cynogenmod 10.1
same problem. any solutions?
I am having the same issue with my home button. Won't press during calls. Did you ever find a solution? Thanks!
rdhalla said:
I have searched and then made this thread. There were some people with home button issue but None of those were related to my problem.
PHONE MODEL - GT-I9505 ( International version)
I have had my S4 for a couple of months now and I am addicted to flashing. I flash a test lot of new roms.
MY PROBLEM
When i make or I get a call, Once i pick the call and put my phone to the ear and after the proximity sensor turns off the screen i cannot use my home button or powerbutton to wake the screen during call. For example if i want to cut the call During a call. I simply cannot do it. Sometimes the home button will respond, Some times it wont
For the home button to work The other party has to cut the all only when my phone detects that the call has been disconnected it wakes up. Looks like the home button stops functioning ?
I dont know what is happening.
I thought it was the rom issue, But it isnt. I tried two different roms. Did the same behaviour.
Any advice or anything to help me will be appreciated. Is my hardware damaged?
My phone is never dropped and is very new like .
ROMS I TRIED
Wanam Lite.
Cynogenmod 10.1
Click to expand...
Click to collapse
jasonbosch said:
I am having the same issue with my home button. Won't press during calls. Did you ever find a solution? Thanks!
Click to expand...
Click to collapse
Go to Apps - Settings - My device - Call - Untick Turn off screen during calls :highfive:

[Q] XT912 screen goes black during calls

Hey there people.
i am hoping some one can help me out a lill here, i have an motorola xt912 i live in sweden atm so it is on a
swedish sim the phone is 100% stock rom.
the issue i am having atm is getting worse when even i make a call the screen goes blank and i carnt do anything
what so ever i have to have Power button set to hang up to end the call then i can get out of the call.
as a rule this is not a huge issue save when i need to call my ISP or somthing when i need to use the nuber pad
like when i call my bank (must to this often) the problem used to be intermittent but now it is prity much every
phone call made this happens.
any one know of a working solution to this problem.
many thanx people
You may get more help posting on the RAZR forum as the xt912 is the og RAZR ... my wife still has the 912 on stock and it did this a few times but I just factory reset it and it resolved the issue.... but on hers the proximity sensor won't turn off it stays on well I can see it illuminated all the time... try it in safe mode see if it still does it... I forget how to do it b4 the update if your on jb just hold the power button till screen pop long press reboot and enter safe mode...
Sent from my XT907 using xda app-developers app
Gauu said:
Hey there people.
i am hoping some one can help me out a lill here, i have an motorola xt912 i live in sweden atm so it is on a
swedish sim the phone is 100% stock rom.
the issue i am having atm is getting worse when even i make a call the screen goes blank and i carnt do anything
what so ever i have to have Power button set to hang up to end the call then i can get out of the call.
as a rule this is not a huge issue save when i need to call my ISP or somthing when i need to use the nuber pad
like when i call my bank (must to this often) the problem used to be intermittent but now it is prity much every
phone call made this happens.
any one know of a working solution to this problem.
many thanx people
Click to expand...
Click to collapse
a.) this is a forum for the XT907, but this resolution process should still be the same
b.) check to make sure that the sensors (upper left-hand corner on the face of the phone) are not blocked. these sensors enable the phone to black out when near your face while in call.

Categories

Resources