Ok today I rooted my lg g2 installed twrp all fine. Then I decided to install the new kit kat Rom. All ready to go went to wipe everything to start a clean install then stupidly wiped the internal storage too. So can't restore back up and can't install the blasted Rom. Phone will get as far as the lg logo. I can get into recovery but usb mounting doesn't work and Adb sideload will not start. If I try to use Adb push it says nothing is attached. Odd thing is the storage left being reported in twrp is just over 10 gig and it is a 16 gig phone so I thought it should be more. I know if it is booting into recovery there is hope but I'm stumped . Any help would be greatly appreciated.
darrenmdr said:
Ok today I rooted my lg g2 installed twrp all fine. Then I decided to install the new kit kat Rom. All ready to go went to wipe everything to start a clean install then stupidly wiped the internal storage too. So can't restore back up and can't install the blasted Rom. Phone will get as far as the lg logo. I can get into recovery but usb mounting doesn't work and Adb sideload will not start. If I try to use Adb push it says nothing is attached. Odd thing is the storage left being reported in twrp is just over 10 gig and it is a 16 gig phone so I thought it should be more. I know if it is booting into recovery there is hope but I'm stumped . Any help would be greatly appreciated.
Click to expand...
Click to collapse
Try to flash your variant older ROM/radio . 16GB phone should have around 11-12GB as free
TWRP OTG to load rom
I was using the d80010d_to_20c.zip firmware + SuperSu.zip + TWRP 2.7.0.0.zip.
i.e. "kitkat" with a custom recovery and root.
I had only the 3 above zips on the phone.
d80010d_to_20c.zip contains the kk_system and a custom kk_kernel, no bootloader.
The bootloader came from the LGFlashTool and a d80010d.tot file on my laptop.
After taking the April 8 OTA from AT&T, my phone was stuck in recovery.
Could not get into download mode or use ADB.
I made the mistake of wiping my phone hoping to get download mode to work.
I should have used the terminal in TWRP and typed:
dd if=/dev/zero of=/dev/block/platform/msm_sdcc.1/by-name/fota
which has been reported to work. After wiping the phone it was too late for this.
I was stuck in TWRP 2.7.0.0 which has OTG capability, so I loaded a usb flash drive with d800_Kitkat.zip,
connected it to my phone via an OTG cable, and copied d800_Kitkat.zip to the sdcard using TWRP.
Then flashed it using TWRP. I also flashed SuperSU.zip before booting to system. I'm back to stock Kitkat + root.
I'm hoping someone with Kitkat + root reports whether the April 8 AT&T OTA works on a rooted phone.
We know it fails badly on a custom recovery phone with Jellybean bootloader/custom Kitkat kernel/Kitkat system.
AT&T claims that it just updates Google+, Google Wallet, and makes Google Hangouts the default messaging app
which sounds safe but isn't.
if you can get in recovery then you should also be able to get into donwload mode. Have you tried flashing a kdz for your phone through the lg flash tool?
Sent from my TF701
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I can confirm root on AT&T new ota is fully functional. No problems thus far. I haven't tried a custom recovery yet though
Edit. Can confirm xposed is working as well. Has anyone with the new ota and root tried this yet? http://forum.xda-developers.com/showthread.php?t=2715496
Sent from my LG-D800 using Tapatalk
Thanks for replies been trying all day and can't pc to even recognise phone. Goes into download mode but no Adb or sub connectivity think it's drivers so trying on different pc .
[QWondarrenmdr;51867286]Thanks for replies been trying all day and can't pc to even recognise phone. Goes into download mode but no Adb or sub connectivity think it's drivers so trying on different pc .[/QUOTE]well not a lot of hope all the kdz files failed tried using Adb sideload no dice. Giving up for today will try again t I tomorrow
ok now this is getting silly. I managed eventually by using Koush's drivers to get adb to work and got cm11 working. Whoopee at least the phone works. So I make a backup. then wipe remembering this time to check the backup works. Then install new 4.4 rom. Restarts but then the touch screen input is all over the place so I can't get anything to work. Ok fine go back to recovery and restore from backup.
But noooooooooooo:crying: The flipping TWRP Recovery has gone. I can get as far as the phone saying it is going to install TWRP and reboot, but it doesn't and doesn't. The KDZ files I've found don't seem to work and the part on the lg support tool that starts updating the phone after you have changed to Korean does zip zilch nada. I can get into download mode.
So is there a CM or lightweight kdz file I can try rather than these 2 gig monstrosities?
Any idea why R and D Test tool doesn't work? I've followed instructions and videos?
Why do I do this every time I get a new phone, it was fine I could have waited but no I had to go and tinker
I know this is fixable because I can get into a software installation but I am stumped at the moment.
Any sort of help or pointing to other tutorials would be greatly appreciated.
fixed
Wow what a kerfuffle. After all that I am back to a stock 4.2 Rom with bloat but I don't care the thing works.
All that was wrong was a # in the wrong place.
Next time read and read again. It's like carpenters with their measures twice cut once
Related
Hi,
I have a Samsung Galaxy S4 GT-i9505. The micro USB port doesn't work : please don't even ask anything to try to make it work, I just tried nearly everything possible (clean up the port, 4 different PC and OS, all the drivers, KIES or nos KIESS, tried to play with the pins, tons of USB mods, tons of cables...). This USB doesn't work at all (apart from charging!).
I would like to update the phone since I'm stuck with a (stock I think?) 4.2.2 not rooted. :crying:
It seems also that I have only Custom Recovery (no wipe data, dalvik and stuff options at all, just basic stuff like "update from zip"..).
I can copy stuff on my ext CD Card or via AirDroid
=> I heard that i could make an OTA update via Stock Recovery but i can't find any file like that. Like that I could do a "update from zip" from Stock Recovery mode (UP+HOME+ON BUTTON)
=> Do you know where i can find this file ? Or do you have any ideas how I would update my phone ? :highfive::highfive:
Here is an image of what i currently have on my galaxy S4 :
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
[/url][/IMG]
Come on, no one can help ? Stuck forever on my 4.2.2 ? Damn, can't even use some features of my chromecast...
Up...
Ill get back at it.
Thanks, I'm all ears !
Before I begin, trying to OTA in the settings menu doesn't work? Settings > About phone > Software update. What is the error message you are getting?
The problem is as follows:
- Because you don't have a working usb port, it's a lot harder to fix things if it goes wrong.
- You can't upgrade/restore using Odin, because you don't have download mode.
There are a few things you can do. It's up to you what you want. The problem is that if something goes wrong, you will probably be unable to restore without a new usb port.
A.
Root your phone using Towelroot. Install Xposed Framework and then install Wanam Xposed. Open Wanam Xposed and click on "Fake system status". That should give you OTA updates back.
Downside to this method: You will probably be unable to root in the new version. The downside of not having root is that having a custom recovery would benefit you greatly, sinds you can't use download mode. In your case you will need root to flash the custom recovery.
B.
Use a custom rom.
There are a few things you will need to get everything working.
1. You will need root.
2. You will need a custom recovery
3. You need to update your modem (Wifi fix/non-hlos).
1.
Rooting should be possible using Towelroot. It should work on 4.2.2.
2.
After that you can flash a custom recovery true "Terminal Emulator". You can download that app in the market. You can find the instruction on how to flash the custom recovery here. http://teamw.in/project/twrp2/182
That's TWRP recovery, if you want a different one, go ahead just use the instructions.
If you the flashing was succesfull, then make a backup in the recovery.
3.
You need to update your modem so that everything will work on the old bootloader. You need Mobile Odin (probably the payed one) to flash the modem. You need a wifi-fix/non-halos version because you are on the old bootloader.
4.
You can flash any custom rom you want.
Lennyz1988 said:
Before I begin, trying to OTA in the settings menu doesn't work? Settings > About phone > Software update. What is the error message you are getting?
The problem is as follows:
- Because you don't have a working usb port, it's a lot harder to fix things if it goes wrong.
- You can't upgrade/restore using Odin, because you don't have download mode.
There are a few things you can do. It's up to you what you want. The problem is that if something goes wrong, you will probably be unable to restore without a new usb port.
A.
Root your phone using Towelroot. Install Xposed Framework and then install Wanam Xposed. Open Wanam Xposed and click on "Fake system status". That should give you OTA updates back.
Downside to this method: You will probably be unable to root in the new version. The downside of not having root is that having a custom recovery would benefit you greatly, sinds you can't use download mode. In your case you will need root to flash the custom recovery.
B.
Use a custom rom.
There are a few things you will need to get everything working.
1. You will need root.
2. You will need a custom recovery
3. You need to update your modem (Wifi fix/non-hlos).
1.
Rooting should be possible using Towelroot. It should work on 4.2.2.
2.
After that you can flash a custom recovery true "Terminal Emulator". You can download that app in the market. You can find the instruction on how to flash the custom recovery here. http://teamw.in/project/twrp2/182
That's TWRP recovery, if you want a different one, go ahead just use the instructions.
If you the flashing was succesfull, then make a backup in the recovery.
3.
You need to update your modem so that everything will work on the old bootloader. You need Mobile Odin (probably the payed one) to flash the modem. You need a wifi-fix/non-halos version because you are on the old bootloader.
4.
You can flash any custom rom you want.
Click to expand...
Click to collapse
Man, thank you so much. Your explaining are crystal clear. I've been stuck for months without no solution until now. :crying::crying:
So here is what I did :
0. First of all as you asked when i was clicking on "update" to search for some OTA updates i didn't have anything. Absolutely nothing happen : i just click on it wihtout any warning. Please note that before I used to have a typical warning message "your device has been modified..." or something like that
1. I rooted my i9505 wIth towelroot, had to change a code in it because i had a message "your device is not yet supported". It woked after that, i installed SuperSu and RootChecker which are working perfectly. Of course RootChecker is telling me that I am well rooted.
2. I downloaded all the Xposed stuff : framework, update, reboot and also the Wanam Exposed.
3. On Wanam i found the "fake system status" on the "security" part. I did it (several times actually). After the reboots my status was on "OFFICIAL" in android AND in the download mode BUT the Binary Status stay always in "Custom". :silly: So when i try again to update via OTA my phone i doesn't do anything at all, just like before...
=> Then I saw that in this case you have to install TriangleAway to set back the official Binary Status to "officiel" again? Is it this way ?
=> I saw your warnings about the flashing. I think that it's too risky, I'm not very confident and don't want to brick it. I flashed a ROM once but doesn't know anything about wifi flash/non-halos, I doesn't even what that means !
=> But i would love to install a "pure" android 4.4.2 or 5.0, i'm just fed up with touchwizz... So I installed GooImager but unfortuately the servers are down now. So I couln't go any further to install a custom recovery. Could you give me another way and also maybe where to find the wifi/non-halos stuff to flash ? or at least a tutorial ?
Thank you very much? :highfive:
Once again, if you have a little time to help me about my last message.. Thank you in advance
I'm not sure if you need a new rmodem. Just go ahead and flash a recovery true the terminal, that's not really dangerous. Then backup and flash a custom rom that you want. If it works, then it works. If it doesn't work, you can always revert back.
The easier thing to do is replace the USB board. The part is less than £10 and is a piece of piss to fit.
Nope, I aleady tried this. Even with a new USB board it wasn't working.
It's either a bug bad bug on the ROM or a bug on the mainboard. I guess...
2 days ago i have flashed @travis82 Nougat Rom that was working fine then i install emoji switcher application to change emoji that app was wanting root permission as soon as I tapped to grant that app message came up that your device is not Rooted, after that i checked Magisk that was saying Magisk is not installed in this device, then i reboot my C9 Pro to twrp mod to flash again Magisk Or Super Su after flashed Su i reboot my device So my mobile was stuck on Samsung C9 Pro Logo, i have waited 30 minutes to see device will start but i t was stuck, then i was coming back to my Stock rom backup so twrp was not showing backup but i was seeing that backup in my laptop, then i flashed C9000ZHU1AQG2 firmware by odin then flashed twrp then SuperSu but same i stuck on Samsung logo screen device not turned on i tried it 3 times flashed firmware/twrp/SU but same issue stuck on Samsung logo now I'm using stock C9000ZHU1AQG2 rom i want to Root again my device can anyone guide me what should i do..? I also tried to flash again @travis82 Nougat and Marshmallow Custom Rooted rom but same issue device is not turning on just stuck on Samsung C9 Pro Logo after flash ??
you format data so encryption is removed? after that install rom? should boot just fine.
travis82 said:
you format data so encryption is removed? after that install rom? should boot just fine.
Click to expand...
Click to collapse
Yes @travis82 before to flash Rom or Super Su i formated data and also swiped to factory reset then i flashed but after flashed when I'm rebooting my device so its not turning on, stuck on Samsung C9 Pro Logo screen to start device i have to flash stock firmware its a problem ?
Maibe you flashed wrong twrp
criszz said:
Maibe you flashed wrong twrp
Click to expand...
Click to collapse
After working very hard and very difficult now Thank God Super Su has Flashed in my mobile by twrp and @criszz I'm using twrp 3.1.1-0 c9ltechn which i downloaded from official twrp.me website twrp maintainer is @travis82 but now I'm getting issues in twrp sometimes format data or factory reset Failed and I'm not able to make backup And restore my Rom its always failed when i tap to make backup and restore and also installing failed sometimes but this twrp was working fine before to this problem which i described in my Post it was working fine since last 3 months but now i don't know why its getting problem with this twrp @travis82 do u know why its getting problem i have downloaded twrp from here which i was using before that time everything was working fine ??
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
cant restore? let me see the recovery log. Maybe the emmc chip is going bad or you need to make sure odin re partitions your phone when you go back to stock.
travis82 said:
cant restore? let me see the recovery log. Maybe the emmc chip is going bad or you need to make sure odin re partitions your phone when you go back to stock.
Click to expand...
Click to collapse
I didn't tick repartition when i flashed the stock rom i just ticked f.reset and auto reboot its just a twrp problem i think @travis82 because in twrp factory reset Failed format data failed sometimes and backup always failed and restore not showing backup files i installed super su with very difficulty because also the installation option not working fine, su or custom rom dirty install
twrp 3.2 has issues dont touch it stay on 3.1
travis82 said:
twrp 3.2 has issues dont touch it stay on 3.1
Click to expand...
Click to collapse
I didn't touch 3.2 twrp and never touch till u will tell me that now touch it but also I'm seeing issues in twrp 3.1 too now what should i do which twrp should i use..? @travis82 issues which I'm getting in twrp 3.1 i described u in my thread
might be having a hardware failure than.
Hi everyone, I had my phone rooted and had TWRP, Magisk fake GPS etc all up and running so I could play a certain GPS based game.
The updated game stopped working so in trying to fix it I ended up factory resetting my phone. So a couple of things, I am trying to follow a guide but I am not sure it is best suited to my current problem. TWRP app says my phone isn't rooted any longer (factory reset?) and when I try to re root the phone I get to this screen but cannot do anything except press volume down key + power key for 7 seconds to reset.
Does it look broken? How do I start all over again with a fresh root to get my phone set up again please?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
As an update I can get into recovery mode and I have TWRP options and full usability here is anybody can advise what to do now please?
Tried installing magisk via TWRP, it installed but now I am stuck on the Samsung logo as the phone is trying to boot up, I really do need some guiding here
Quinn23 said:
Tried installing magisk via TWRP, it installed but now I am stuck on the Samsung logo as the phone is trying to boot up, I really do need some guiding here
Click to expand...
Click to collapse
Twrp does not detect whether your phone is rooted or not.
What guide did you follow?
Stuck at which Samsung logo ( Samsung powered by Android or Samsung with blue led light) and how long did you wait?
Being from a factory reset your phone is probably re-encrypted so you will have to format data and flash no Verity zip again.
spawnlives said:
Twrp does not detect whether your phone is rooted or not.
What guide did you follow?
Stuck at which Samsung logo ( Samsung powered by Android or Samsung with blue led light) and how long did you wait?
Being from a factory reset your phone is probably re-encrypted so you will have to format data and flash no Verity zip again.
Click to expand...
Click to collapse
This guide...
https://www.reddit.com/r/PokemonGoSpoofing/comments/9kzf4g/tutorial_spoofing_on_all_android_devices/
All worked well until yesterday when a pokemon update downloaded. So I reverted the game file back a build and it worked again.
Then today I had a notification saying there is a magisk update, in magisk manager it says ""Magisk is not installed. Latest v18.1 (18100)"". Then trying to boot into pokemon go the game will not launch as my software is incompatible.
So basically I figured I will do a phone factory reset and set it all up again with the edited guide since the updates and I am now running into errors. I have managed to since get into the phone and can get into TWRP recovery again but I cannot get magisk to instal, this is my question on reddit and where I am at currently...
Hello everyone,
I am having huge issues here. I was using the pinned guide from here method for around 6 weeks until today. I set my phone back to factory settings as I had a lot of issues. Phone is as new now but TWRP is still installed as a recovery mode available. I am on a samsung galaxy s8.
Whenever I try to install Magisk via TWRP flashing method I get "install magisk failed to mount '/data' (no such process)"
If I reset the phones file system so try EXT 2,3 etc and eventually set it back on EXT 4 then magisk installs seemingly but then my phone resets to factory and I do not see magisk anywhere once setting my phone up again.
Then if I install magisk manager it says "Magisk is not installed. Latest v18.1 (18100)"
I cannot do anymore to get set up until I get magisk going again.
Please can anybody advise?
Click to expand...
Click to collapse
Quinn23 said:
This guide...
https://www.reddit.com/r/PokemonGoSpoofing/comments/9kzf4g/tutorial_spoofing_on_all_android_devices/
All worked well until yesterday when a pokemon update downloaded. So I reverted the game file back a build and it worked again.
Then today I had a notification saying there is a magisk update, in magisk manager it says ""Magisk is not installed. Latest v18.1 (18100)"". Then trying to boot into pokemon go the game will not launch as my software is incompatible.
So basically I figured I will do a phone factory reset and set it all up again with the edited guide since the updates and I am now running into errors. I have managed to since get into the phone and can get into TWRP recovery again but I cannot get magisk to instal, this is my question on reddit and where I am at currently...
Click to expand...
Click to collapse
Can't help with pokemon as I don't play it
In regards with twrp/magisk after you factory reset your phone would have re-encrypted itself so in twrp you will have to format data reboot back into twrp flash the no Verity zip and magisk again.
Note: Once phone is up and running with root I would do a twrp backup first then try your Pokemon guide so if you run into troubles you can restore from backup.
Quinn23 said:
Tried installing magisk via TWRP, it installed but now I am stuck on the Samsung logo as the phone is trying to boot up, I really do need some guiding here
Click to expand...
Click to collapse
Format device in twrp, flash magisk, flash DM Verity zip and it will boot
Hi Guys,
My son has a MI9T.
Hé wanted to flash a custom rom the day after he got this phone from me (why i dont know) but he never did it before. And i aM no expert either.
Hé installed a few custom kernals, and roms and TWRP'S and dont actually know what hé is dooing.
But the phone is stuck in startup screen with Every rom he installed so far.
Hé did no backups from the working device either........???
The phone have working TWRP now and unlocked bootloader.
i tried to do the Xiaomi recovery (Miflashtool) but wont work either cuz of the fault:
Anti Rollback protection and i cant find a right firmware for IT.
The anti rollback protection is on 1 on this phone.
Can Any one help me out maybe?
or is the phone already to throw away?
Hi. The anti-rollback protection exists purely in a file in the fastboot image. Here is a tutorial on how to avoid triggering it on our device:
https://telegra.ph/Fix-fastboot-flashing-problems-09-20
The reason that no roms he tried are booting is most likely that on this device he has to wipe data + internal storage after flashing or it will most likely not boot.
nckmml said:
Hi. The anti-rollback protection exists purely in a file in the fastboot image. Here is a tutorial on how to avoid triggering it on our device:
https://telegra.ph/Fix-fastboot-flashing-problems-09-20
The reason that no roms he tried are booting is most likely that on this device he has to wipe data + internal storage after flashing or it will most likely not boot.
Click to expand...
Click to collapse
i tried to do that but now i have an error: flash crc list error
so it wont work either i guess.
olso tried to flash another rom and did wipe data + internal storage but no effect, still stuck in startup.
Bramcl said:
Hi Guys,
My son has a MI9T.
Hé wanted to flash a custom rom the day after he got this phone from me (why i dont know) but he never did it before. And i aM no expert either.
Hé installed a few custom kernals, and roms and TWRP'S and dont actually know what hé is dooing.
But the phone is stuck in startup screen with Every rom he installed so far.
Hé did no backups from the working device either........???
The phone have working TWRP now and unlocked bootloader.
i tried to do the Xiaomi recovery (Miflashtool) but wont work either cuz of the fault:
Anti Rollback protection and i cant find a right firmware for IT.
The anti rollback protection is on 1 on this phone.
Can Any one help me out maybe?
or is the phone already to throw away?
Click to expand...
Click to collapse
Download the latest fastboot rom for your device. Extract it and open the flash_all.bat file with Notepad++. Remove all the lines before "fastboot% erase.." line. Then run the bat file.
Preetam286 said:
Download the latest fastboot rom for your device. Extract it and open the flash_all.bat file with Notepad++. Remove all the lines before "fastboot% erase.." line. Then run the bat file.
Click to expand...
Click to collapse
thx for reaction
i deleted lines and made sure that fastbootlines start on 1st line now
but now its says flash crclist error.
Try to Flash fastboot rom from EDL mode... You have unlocked bl, download this tool
https://github.com/Saki-EU/XiaomiAD...ad/6.6.2/XiaomiADBFastbootTools-6.6.2-Win.zip
Put phone with this tool in EDL mode and try to flash fastboot rom.
Bramcl said:
thx for reaction
i deleted lines and made sure that fastbootlines start on 1st line now
but now its says flash crclist error.
Click to expand...
Click to collapse
Move the fastboot rom folder (with the modified bat file) to C:/. Then try flashing again with miflashtool.
nothing worked for me. tried all the above and many other tricks but no.
zkrayem said:
nothing worked for me. tried all the above and many other tricks but no.
Click to expand...
Click to collapse
OK! Let's try something different. First of all, the phone is not dead, so, don't worry. We just have to figure it out.
Enter TWRP, format DATA, tipe Yes (it's not wipe, it's format data).
Just to be sure, flash the latest TWRP https://dl.twrp.me/davinci/twrp-3.4.0-0-davinci.img
Since you formated data, you will have no files on your phone (be shure of that, if it isn't empty, you haven't formated data), you have to tranfer this TWRP from the computer or OTG.
After flashing TWRP, reboot to recovery. Now, let's flash some stable rom. Try this: https://sourceforge.net/projects/xi...K20MI9T_V12.0.4.0.QFJCNXM_v12-10.zip/download
Flash only the rom (no magisk, nothing). Reboot! Now, wait patiently. The first boot will take time (from 5 to 10 minutes).
Then, give us feedback. Ground your son until the weekend. Good luck, mate!
Hi
Do you find solutions???
used the above steps except edl mode and was able to sucessfully flash fastboot rom without crc list error
RCstZero1 said:
Move the fastboot rom folder (with the modified bat file) to C:/. Then try flashing again with miflashtool.
Click to expand...
Click to collapse
Thanks, mate for the suggestion. Initially was getting anti-rollback check then crc error. Your suggestion save my day. Again Thankyou very much. In the end, got this error but the device booted successfully.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hello everyone.
I have Rooted my Samsung Galaxy Tab S6 lite WIFI successfully, then I tried to flash the recovery with TWRP to install LineosOS, but after flashing with TWRP I can't boot the system anymore and it just turns into Download Mode with an error on the screen.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
ODIN MODE (AVB Fail)
recovery: Error verifying vbmeta image: invalid vbmeta header (6)
CUSTOM RECOVERY
VMMETA P610XXX.......
My Samsung Galaxy Tab s6 lite still recognize via USB to my PC and ODIN too.
I've tried to install the Stock AP with ODIN, but it didn't work.
Can this damage still be repaired? or it is already a Soft bricked with no solution?
Thanks!
I had a similar issue but I used this to fix it
How To Fix "An Error Occurred While Updating The Device Software" On Galaxy Smartphone? - SamsungSFour.Com
How To Fix "An Error Occurred While Updating The Device Software" On Galaxy Smartphone?
www.samsungsfour.com
dimacari said:
I had a similar issue but I used this to fix it
How To Fix "An Error Occurred While Updating The Device Software" On Galaxy Smartphone? - SamsungSFour.Com
How To Fix "An Error Occurred While Updating The Device Software" On Galaxy Smartphone?
www.samsungsfour.com
Click to expand...
Click to collapse
I trieded both Software but this could not solve my problem.
One thing that you should probably know is that development of TWRP for the S6 Lite was stopped due to various issues, and the developer has no interest in resuming. If/when you get the issue with your tablet resolved, you'll have to flash and use LineageOS recovery to install LineageOS, Magisk, GApps, etc.
MJPollard said:
If/when you get the issue with your tablet resolved, you'll have to flash and use LineageOS recovery to install LineageOS, Magisk, GApps, etc.
Click to expand...
Click to collapse
Hold on....are you saying that the Lineage Recovery can be used instead of TWRP?? I was under the impression that TWRP had to be installed to use Lineage? It didnt escape me that there was a Lineage recovery file, but since everything i read insisted TWRP recovery had to be used I just kept on trying to install it (failing every time...definition of insanity).
OP.....I have soft bricked and reinstalled the stock ROM on my device literally DOZENS of times trying to install TWRP....are you absolutely sure you have the correct one for your device? Maybe the stoc ROM you have has a glitch in it? If you are positive that you have a S6 lite, wifi only, pm me and maybe i can send you a copy of my stock ROM? If i can help i will gladly pay it forward.
vstarjewel said:
Hold on....are you saying that the Lineage Recovery can be used instead of TWRP?? I was under the impression that TWRP had to be installed to use Lineage? It didnt escape me that there was a Lineage recovery file, but since everything i read insisted TWRP recovery had to be used I just kept on trying to install it (failing every time...definition of insanity).
Click to expand...
Click to collapse
Yup, it certainly can. LOS Recovery is pretty basic compared to TWRP, but it supports the S6 Lite's SD card as well as USB OTB and ADB sideloading. You have to flash one file at a time, though, and every time you access the card it starts at the root directory (rather than remembering the last directory you were in), but those are minor annoyances. Also, flashing Magisk will trigger a warning regarding file signing, but you can override it and it'll work just fine (just wanted to FYI this bit). I truly wish we had a fully functioning TWRP, but since we don't, LOS Recovery will have to do.
MJPollard said:
Yup, it certainly can. LOS Recovery is pretty basic compared to TWRP, but it supports the S6 Lite's SD card as well as USB OTB and ADB sideloading. You have to flash one file at a time, though, and every time you access the card it starts at the root directory (rather than remembering the last directory you were in), but those are minor annoyances. Also, flashing Magisk will trigger a warning regarding file signing, but you can override it and it'll work just fine (just wanted to FYI this bit). I truly wish we had a fully functioning TWRP, but since we don't, LOS Recovery will have to do.
Click to expand...
Click to collapse
You are my hero! I am sending this from my tablet with a SUCCESSFULLY installed Lineage OS. I LOVE not having all the Samsung crap taking up space. I have an SD card installed and formatted but have yet to it anything on it. Question though...what would installing Magisk do to improve the tablet performance?
vstarjewel said:
You are my hero! I am sending this from my tablet with a SUCCESSFULLY installed Lineage OS. I LOVE not having all the Samsung crap taking up space. I have an SD card installed and formatted but have yet to it anything on it. Question though...what would installing Magisk do to improve the tablet performance?
Click to expand...
Click to collapse
Nothing. The main reason to install Magisk is if you were going to root your tablet. If you aren't going to do that, Magisk offers very little benefit, thus you can safely skip it.
Glad to hear you got LOS installed and running! It certainly does breathe new life into the S6 Lite.