Related
Hi all,
i tried to flash cyanogenmod unofficial, on the flash an error was comming, now the device dosent start...
when i boot the phone normaly, is comming: firmware upgrade encountered an issue. please select recovery mode in kies & try again.
i tryed to flash the original firmware:
(I9505XXUAMDF_I9505AUTAMD8_AUT)
I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar
but an error in odin is comming:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Removed!!
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
please can you help me?
cutalaxy said:
Hi all,
i tried to flash cyanogenmod unofficial, on the flash an error was comming, now the device dosent start...
when i boot the phone normaly, is comming: firmware upgrade encountered an issue. please select recovery mode in kies & try again.
i tryed to flash the original firmware:
(I9505XXUAMDF_I9505AUTAMD8_AUT)
I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar
but an error in odin is comming:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Removed!!
<ID:0/006> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
please can you help me?
Click to expand...
Click to collapse
Try flashing along with pit file
MKe sure u have the proper file for the same
Sent from my GT-I9500 using xda premium
123hiten said:
Try flashing along with pit file
MKe sure u have the proper file for the same
Sent from my GT-I9500 using xda premium
Click to expand...
Click to collapse
where can i find the pit file?
cutalaxy said:
where can i find the pit file?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2265477&highlight=stock+firmware
this link has it attached take the correct one u would know better
dont worry i had the same issue on my note 2 a month ago and was wrkng fine after flashing rescue firmware urs wil work too
damn, it doeset work for me
is it hard brick?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
cutalaxy said:
damn, it doeset work for me
is it hard brick?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUAMDF_I9505AUTAMD8_I9505XXUAMDF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
No its not at a hard brick dont worry dont panic thats the best wat to work around
I would say dont use pit file unless its last option and try without that only may be in other pc using other cable some below steps myte also help u
2) Install later Kies.
3) Kill al kies applications (all 4 of them).
disable antivirus or whatever you got there.) Get to Download Mode and push Vol Up.
7) Open Odin.
8) Plug the device to your laptop.
Does it see the device?
If NO:
A) Get another usb cable, are you using ?
B) Try different Odin Versions (download 3 or 4).
C) Try another USB port.
D) Still no luck? reboot the pc and start from step 3.
---------- Post added at 08:30 PM ---------- Previous post was at 08:23 PM ----------
Download 2/3 stock firmware and try installing thru ODIN it should work
Make sure u have all the drivers installed
MAke sure kies is not open or make sure its closed even in background process
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
cutalaxy said:
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
Click to expand...
Click to collapse
Official firmware is not a wiping one. It doesnt flash userdata, it replace system, recovery, and some other partitions.
sent from my Galaxy
cutalaxy said:
okay, with odin 1.85 now has worked phu... lucky
but i'm confused... all(!) my settings and apps etc. are still installed and settet? why dat?
only root is going... i'm now flashing root again
i think i will wait for an official CWM and official Cyanogen... is to hot for me
@123hiten
thank you very much!! I thought now i have to get out 700$ again... :S
Click to expand...
Click to collapse
Great to hear that man
If u flash stock firmware all will remain as its in ODIN but its good if u reset the device after or b4 root
Also take a EFS backup of ur device and be safe
i had root before the device bricks... so i rootet it now again, and works good...
yeah, i will backup efs (hope this <- works...)
yah, thank you again...
have a nice day..
OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Sounds like a bad rom download. Download the rim again or get it from a sticky on xda.
Also it doesn't matter what com port Odin puts the phone on as long as it sees it.
Sent from my SPH-L720 using xda app-developers app
tordsrv 1892
im still fairly new at the whole rooting scene. could you possible link me to the stock rom? oh btw idk if this would matter but i think i had the MF9..
i just want to go back stock for now and get this phone to work.. than i will try again.. thank you in advance!
my uncle also said there is a odin file not the program. but an odin file that you use with odin program. is this true for the s4? if so could you link me to it also!
i just tried it again. and im getting this error now..
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I have read that that download fron QBKing is bad. As a poster above me said, download the rom from XDA instead and redo the process. Also, be sure to use the usb cable that came with your phone as others can cause the same issue. Also....if it fails again, try a different usb port. Good luck
Sent from my SPH-L720 using Tapatalk 4 Beta
could someone link me to the right post that has the sprint stock rom? thank you
texassoljaz said:
could someone link me to the right post that has the sprint stock rom? thank you
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2382188
Last post
Sent from my SPH-L720 using xda premium
and ubuings
ok so.. i downloaded this stock firmware
http://forum.xda-developers.com/showthread.php?t=2258107
and it actually goes futher but than it said i dont have a pit file.. im sorry this is my first time and it is so hard to understand everything.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
texassoljaz said:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MF9FirmwareAIO.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
could someone tell me wht it says no PIT partition? i have tried so many different stocks for the sprint phone.
im sure mines was the MF9. but i also tried the MDL and MDC.
Click to expand...
Click to collapse
Bot trying to scare you here but if you google the pit error people are being told its a faulty motherboard
Sent from my SPH-L720 using xda premium
same thing happen to my boys gs2 when i was flashing a recovery for him... same ishh.. all i had to do is use odin to unroot and flash a stock rom via odin.. its worked for me.. all the phone would do is go into download mode.. thats it.. no recovery and it wouldnt boot.. stuck in download mode.. i plugged it in to my pc.. odin noticed the phone i flashed stock unrooted rom.. phone rebooted at the end and everything was fine..one crazy thing was after that happen i tried to root again and flash a custom recovery and it happen again.. so i had to fix it again.. i just could not root that phone after that.. had to keep it stock.. my buddy was just happy to have his phone he didnt care about root after that!!
texassoljaz said:
OK so this is what i did. so i tried to root my s4, and in odin it said fail. so i took out the battery. and try to turn it on now it has the phone YELLOW triangle and a monitor. it says "firumware upgrade encountered an issue. Please select recovery mod in kies & try again.
what i have tried so far was download the sprint stock and odin it back. i used qbking77 . com the stock i used is linked on that website. which then links me to stockroms.net. so during the process of doing going back to stock it said fail. i read some where that in the id:com on odin, it should say 0:[COM6] and i read some where else that it does have to say com6 it could say com3. i dont know if that matters. and i also read on the forum they say to use another stock rom? is that also if so where can i get one besides from stockroms.net please someone help me..
this is what it says when i try to odin to stock:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Added!!
Click to expand...
Click to collapse
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
I tried what you said than it went to this
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
texassoljaz said:
I tried what you said than it went to this
Added!!
Odin v.3 engine (ID:7)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Complete(Write) operation failed.
Added!!
All threads completed. (succeed 0 / failed 1)
but now i have a loading bar on my phone. so i dont know whats going to happen i will leave it for a while to see what happens.
Click to expand...
Click to collapse
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
ROMANTiC KiD said:
Its not really a bad download, had this issue once before when I soft bricked my s4 and I needed to restore it back to stock. You need to delete the .md5 extension and leave it with the .tar extension and that should work! Good luck!
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
ROMANTiC KiD said:
Hmm weird. Redownload the file from qbking77 and delete the extension again. Also try it with a different version of odin for example the one that qbking uses v1.85 (which is also the one I use) and pull out battery and put the battery in and manually set it to download mode and try it one more time. Btw any chance did you get a pop up in your screen saying something about an error of some kind saying about a parameter before?
Edit: Also probably restart computer just in case also.
Sent from my SPH-L720 using xda app-developers app
Click to expand...
Click to collapse
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
texassoljaz said:
no i never never got a parameter error.. i also have window 8 do you think that will affect anything? i will try qbking than update you.. thanks for helping. greatly appreciated!
Click to expand...
Click to collapse
Hmm... alrighty. Nah it shouldnt affect anything but you can also try with other computer as well or different version of windows. No problem hope you get it solved soon!
Sent from my SPH-L720 using xda app-developers app
so after trying it. i got a parameter error. what does this mean?
so i end up getting this far.. do you know how to fix this?
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> aboot.mbn
<ID:0/010> NAND Write Start!!
<ID:0/010> tz.mbn
<ID:0/010> boot.img
<ID:0/010> recovery.img
<ID:0/010> system.img.ext4
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/010> Added!!
i dont get it. so i got it to start the green bar in on odin.. than all of a sudden it say fails. and one my phone the blue bar went half way
yessss!!!!! i got
I rooted my s4 just to try it and I'm stuck trying to get it to go back to stock.
I have a note 3 now and I've got everything going well with that but the s4 (I have the I337).
I have it rooted and the phone will start and is a perfectly functional android phone, but whenever I try to get it into recovery mode I can only get it to go to download mode. Odin flashes to stock fail with this:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
the stock flash was linked to by others I found on XDA.
Also, details about the phone:
Jelly Bean 4.2.2
Baseband I337UCAMF3
Clockworkmod 6.0.4.4
Thanks for any and all help!
attbrandon said:
I rooted my s4 just to try it and I'm stuck trying to get it to go back to stock.
I have a note 3 now and I've got everything going well with that but the s4 (I have the I337).
I have it rooted and the phone will start and is a perfectly functional android phone, but whenever I try to get it into recovery mode I can only get it to go to download mode. Odin flashes to stock fail with this:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
the stock flash was linked to by others I found on XDA.
Also, details about the phone:
Jelly Bean 4.2.2
Baseband I337UCAMF3
Clockworkmod 6.0.4.4
Thanks for any and all help!
Click to expand...
Click to collapse
You cannot add a custom recovery to MF3 if the phone came with that firmware you will get hard brick
Sent From My Galaxy S4 SAMSUNG-SGH-I337 Running On New Deadly Venom v1.3.6 Jelly Bean 4.3
---------- Post added at 04:55 PM ---------- Previous post was at 04:51 PM ----------
Venom0642 said:
You cannot add a custom recovery to MF3 if the phone came with that firmware you will get hard brick
Sent From My Galaxy S4 SAMSUNG-SGH-I337 Running On New Deadly Venom v1.3.6 Jelly Bean 4.3
Click to expand...
Click to collapse
I wish I could help more but I'm on the road hopefully someone will explain it better then what I mention.
Sent From My Galaxy S4 SAMSUNG-SGH-I337 Running On New Deadly Venom v1.3.6 Jelly Bean 4.3
Because you are on MF3, the bootloader is locked and there is no exploit. Therefore, custom recoveries won't install. The reason ODIN is failing is because you are using the MDB files instead of MF3. It is impossible to downgrade the firmware back to any previous version. If you want a recovery, the most you can get is Safestrap, but make sure you read up plenty on it before you install it, as it is not a normal recovery and is not even installed to the recovery partition.
need help
every time i try to reset my galaxy s4 att to stock it fails heres what it says
<OSM> Enter CS for MD5.. <OSM> Check MD5.. Do not unplug the cable.. <OSM> Please wait.. <OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid. <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS.. <ID:0/005> Added!! <ID:0/005> Odin v.3 engine (ID:5).. <ID:0/005> File analysis.. <ID:0/005> SetupConnection.. <ID:0/005> Initialzation.. <ID:0/005> Get PIT for mapping.. <ID:0/005> Firmware update start.. <ID:0/005> aboot.mbn <ID:0/005> NAND Write Start!! <ID:0/005> FAIL! (Auth) <OSM> All threads completed. (succeed 0 / failed 1)
ramiijabedd said:
every time i try to reset my galaxy s4 att to stock it fails heres what it says
<OSM> Enter CS for MD5.. <OSM> Check MD5.. Do not unplug the cable.. <OSM> Please wait.. <OSM> I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5 is valid. <OSM> Checking MD5 finished Sucessfully.. <OSM> Leave CS.. <ID:0/005> Added!! <ID:0/005> Odin v.3 engine (ID:5).. <ID:0/005> File analysis.. <ID:0/005> SetupConnection.. <ID:0/005> Initialzation.. <ID:0/005> Get PIT for mapping.. <ID:0/005> Firmware update start.. <ID:0/005> aboot.mbn <ID:0/005> NAND Write Start!! <ID:0/005> FAIL! (Auth) <OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Grab the MF3 Odin flashable tars and flash them the same way to get back to complete factory stock. Or you can get the MK2 tars and update to 4.3 and use Saferoot to easily get root since you already have drivers installed. Then look up how to install Safestrap for MK2, (which is really not too difficult), and TWRP v3.71to use as a recovery.
Now I can’t install firmware or go into recovery mode but I can still get to download screen.
okizen said:
Now I can’t install firmware or go into recovery mode but I can still get to download screen.
Click to expand...
Click to collapse
Cant you go to the download screen and set ODIN away again?
Thats how I did it.
trubster said:
Cant you go to the download screen and set ODIN away again?
Thats how I did it.
Click to expand...
Click to collapse
Hi trubster, I've reset odin and my phone into download mode several times. The odin update process starts off ok but always fails when it reaches 'SYSTEM'.
okizen said:
Hi trubster, I've reset odin and my phone into download mode several times. The odin update process starts off ok but always fails when it reaches 'SYSTEM'.
Click to expand...
Click to collapse
What message is ODIN giving in the white text box?
have you tried re-downloading the ROM? I used the MEGA link and it worked fine.
N9005XXUENA6_N9005OXXENA5_XEO.zip is the one you need if it is for the N9005, you need the stock 4.4.2 FW before you can put CFW on
trubster said:
What message is ODIN giving in the white text box?
have you tried re-downloading the ROM? I used the MEGA link and it worked fine.
N9005XXUENA6_N9005OXXENA5_XEO.zip is the one you need if it is for the N9005, you need the stock 4.4.2 FW before you can put CFW on
Click to expand...
Click to collapse
These are the messages I get from odin (from the beginning).
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENA6_N9005OXXENA5_N9005XXUENA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
I should also mention that I has tripped my Knox to 0x1as I've always got on without one but I doubt if that would be the cause.
That file seems to be different, are you using a N9005?
https://mega.co.nz/#!jZYkyY5a!HfiJlXRgp_ZGWoQncFNWeEn5FnY_0i9iFb23EGfg2Nk
Thats the file I used first, put it in the PDA or AP box on odin and click start.
Should have no problems with it as it is an "Official" Sammy Rom
If you have a Hong Kong note you need to have a read around, If not, grab XEO firmware flash via odin 1.85 or 3.07
trubster said:
That file seems to be different, are you using a N9005?
https://mega.co.nz/#!jZYkyY5a!HfiJlXRgp_ZGWoQncFNWeEn5FnY_0i9iFb23EGfg2Nk
Thats the file I used first, put it in the PDA or AP box on odin and click start.
Should have no problems with it as it is an "Official" Sammy Rom
Click to expand...
Click to collapse
Sorry trubster, I missed out a part of the message in odin.
This is the FULL message in it's entirety.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUENA6_N9005OXXENA5_N9005XXUENA2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
I've also tried the firmware from your link but unfortunately the results were the same.
I didn't experience this on my N9005 while updating, but I experienced this before on my S3, it was due to corrupted firmware file.
Please help me!!! Please!!!
okizen said:
sorry trubster, i missed out a part of the message in odin.
This is the full message in it's entirety.
<osm> enter cs for md5..
<osm> check md5.. Do not unplug the cable..
<osm> please wait..
<osm> n9005xxuena6_n9005oxxena5_n9005xxuena2_home.tar.md5 is valid.
<osm> checking md5 finished sucessfully..
<osm> leave cs..
<id:0/003> added!!
<id:0/003> odin v.3 engine (id:3)..
<id:0/003> file analysis..
<id:0/003> setupconnection..
<id:0/003> initialzation..
<id:0/003> get pit for mapping..
<id:0/003> firmware update start..
<id:0/003> aboot.mbn
<id:0/003> nand write start!!
<id:0/003> sbl1.mbn
<id:0/003> rpm.mbn
<id:0/003> tz.mbn
<id:0/003> sdi.mbn
<id:0/003> non-hlos.bin
<id:0/003> boot.img
<id:0/003> recovery.img
<id:0/003> system.img.ext4
<id:0/003> complete(write) operation failed.
<osm> all threads completed. (succeed 0 / failed 1)
<id:0/003> removed!!
<id:0/003> added!!
<id:0/003> removed!!
I've also tried the firmware from your link but unfortunately the results were the same.
Click to expand...
Click to collapse
i am also having this problem
it seems i cant flash other firmware other than poland fw...
I want ro revert back to ksa firmware or anygood fw since poland svoice isnt working fine<< sorry for bag english
please help me
i have flash my fw with kk italy, and spain but to luck,,, still having the same result... Failed!!!
Please please
u have to download hungry firmwar from sammobiles.com..it will b ok.and tick update boot loader must
clowrid1128 said:
i am also having this problem
it seems i cant flash other firmware other than poland fw...
Click to expand...
Click to collapse
I had the same problem... Just try to flash with this version of ODIN:
https://mega.co.nz/#!RVVXSYiY!6lynzTh-II8o8rvfYkdZzrYa_7m2F-CKgtItMZA66v4
I had the same problem today.The solution is here http://www.cultofandroid.com/53963/save-galaxy-note-3-failed-kitkat-update-odin-tip/
Now i am with german kit kat (DBT) and everything is ok !!!!!! :good::good::good:
Help me (SAM SM-N900S)
<ID:0/023> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BL_N900SKSU0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_N900SKSU0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_SKT_N900SSKT0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_N900SKSU0GPI1_CL9178490_QB10835717_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/023> Removed!!
<ID:0/028> Added!!
<ID:0/028> Odin engine v(ID:3.1005)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Set PIT file..
<ID:0/028> DO NOT TURN OFF TARGET!!
<ID:0/028> FAIL!
<ID:0/028>
<ID:0/028> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/028> Removed!!
<ID:0/028> Added!!
<ID:0/028> Odin engine v(ID:3.1005)..
<ID:0/028> File analysis..
<ID:0/028> SetupConnection..
<ID:0/028> Initialzation..
<ID:0/028> Set PIT file..
<ID:0/028> DO NOT TURN OFF TARGET!!
<ID:0/028> FAIL!
<ID:0/028>
<ID:0/028> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/028> Removed!!
:crying:
Why are you flashing Kitkat ??
What phone have you got and what have you done before .
PIT showing as no partition fail .
Hey guys, I m trying to flash stock rom on my S3 Neo GT-I9301I but i dont work. here is odin code. i tried almost everything please help. it stucks always. even when i try to install a recovery it stucks at recovery.img. again here is the code
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G7102XXUBNG4_G7102ODDBNG4_G7102DDUBNF4_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
PLEASE HELP ME GUYS :crying::crying:
You have selected the wrong file, that is for another smartphone
Alessandro's said:
You have selected the wrong file, that is for another smartphone
Click to expand...
Click to collapse
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXXUANL1_I9301IOXAUANL1_I9301IXXUANI2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
My device is normaly a GT-I9301I but i suddenly installed GT-I9300I. The only things i can do with phone right now is: entering recovery(twrp) and downlaod mod.
I want now the stock rom of GT-I9301I what can i do now?? :crying::crying:
Flash the right firmware for your phone.
Jhnsn said:
Flash the right firmware for your phone.
Click to expand...
Click to collapse
As you can see the odin code above it stucks at sbl1.mdn or am i doing something wrong?
I tried it with another Firmware
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXXUAOJ1_I9301ITTRAOH2_I9301IXXUAOD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
again Stuck
No mather what firmware i try to install everytime it stucks
HELP PLEASE
AnroidLover said:
Hey guys, I m trying to flash stock rom on my S3 Neo GT-I9301I but i dont work. here is odin code. i tried almost everything please help. it stucks always. even when i try to install a recovery it stucks at recovery.img. again here is the code
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G7102XXUBNG4_G7102ODDBNG4_G7102DDUBNF4_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
PLEASE HELP ME GUYS :crying::crying:
Click to expand...
Click to collapse
or try another version of odin
Alessandro's said:
or try another version of odin
Click to expand...
Click to collapse
already tried. but where should i put the firmware? PDA, CSC, PHONE, AP? i tried already AP and PDA and almost every version of odin
http://www.sammobile.com/firmwares/download/64471/I9301IXCUAOL3_I9301IITVAOL1_ITV/
this is one of the latest firmware avaiable on sammobile for gt-i9301i
http://forum.xda-developers.com/attachment.php?attachmentid=1140630
this is odin
Alessandro's said:
http://www.sammobile.com/firmwares/download/64471/I9301IXCUAOL3_I9301IITVAOL1_ITV/
this is one of the latest firmware avaiable on sammobile for gt-i9301i
http://forum.xda-developers.com/attachment.php?attachmentid=1140630
this is odin
Click to expand...
Click to collapse
Thank u A lot, i m gonna try it.
AnroidLover said:
already tried. but where should i put the firmware? PDA, CSC, PHONE, AP? i tried already AP and PDA and almost every version of odin
Click to expand...
Click to collapse
in the newer version of odin AP is the same of PDA
of the older version
Alessandro's said:
http://www.sammobile.com/firmwares/download/64471/I9301IXCUAOL3_I9301IITVAOL1_ITV/
this is one of the latest firmware avaiable on sammobile for gt-i9301i
http://forum.xda-developers.com/attachment.php?attachmentid=1140630
this is odin
Click to expand...
Click to collapse
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Failed :crying:
WAY 1 : ------- VERY DANGEROUS, NOT TESTED, I'M NOT REAPONSIBLE FOR ANY DAMAGE DONE TO YOUR DEVICE, I WARNED YOU.
You need to get TWRP recovery, then download the Utility from HERE and then mount everything, so that your computer can access your device and then put your Utility wherever you want. Then go to install and select the utility.zip and after the program opens then go to next > primary > wipe System and cache and data and dalvik cache... MAKE A BACKUP FIRST! and then go to ODIN mode and flash your OS...
WAY 2 ----- BETTER
Go to TWRP, wipe all data including system and go to ODIN mode and flash the OS, NOT TESTED ASWELL BUT TRY WITHOUT DELETING SYSTEM FIRST!!!
WAY 3 -------
Flash a custom ROM like CM... if you need help at it, ASK! I'll reply to you as soon as possible!
Good Luck!
FireGhost1337 said:
WAY 1 : ------- VERY DANGEROUS, NOT TESTED, I'M NOT REAPONSIBLE FOR ANY DAMAGE DONE TO YOUR DEVICE, I WARNED YOU.
You need to get TWRP recovery, then download the Utility from HERE and then mount everything, so that your computer can access your device and then put your Utility wherever you want. Then go to install and select the utility.zip and after the program opens then go to next > primary > wipe System and cache and data and dalvik cache... MAKE A BACKUP FIRST! and then go to ODIN mode and flash your OS...
WAY 2 ----- BETTER
Go to TWRP, wipe all data including system and go to ODIN mode and flash the OS, NOT TESTED ASWELL BUT TRY WITHOUT DELETING SYSTEM FIRST!!!
WAY 3 -------
Flash a custom ROM like CM... if you need help at it, ASK! I'll reply to you as soon as possible!
Good Luck!
Click to expand...
Click to collapse
WAY 1
---------
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WAY 2
---------
Tried allready. Non worked for me. Like always Stuck.
WAY 3
---------
Tried. It bring me back to recovery when i m trying to boot it
AnroidLover said:
WAY 1
---------
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WAY 2
---------
Tried allready. Non worked for me. Like always Stuck.
WAY 3
---------
Tried. It bring me back to recovery when i m trying to boot it
Click to expand...
Click to collapse
Hmm... seems to be a very advanced error but don't worry!
WAY 4 ---------- Safest
Install newest odin and don't check anything in ODIN's settings, the rom will do all that stuff
---------- Post added at 06:48 PM ---------- Previous post was at 06:45 PM ----------
AnroidLover said:
WAY 1
---------
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9301IXCUAOL3_I9301IITVAOL1_I9301IXXUAOL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WAY 2
---------
Tried allready. Non worked for me. Like always Stuck.
WAY 3
---------
Tried. It bring me back to recovery when i m trying to boot it
Click to expand...
Click to collapse
Oh by the way you made way 3? You installed the custom rom? As a zip file? Like Cyanogen? And it took you back to recovery? What recovery do you have? And did you UNCHECK the signature check? IT'S VERY IMPORTANT
FireGhost1337 said:
Hmm... seems to be a very advanced error but don't worry!
WAY 4 ---------- Safest
Install newest odin and don't check anything in ODIN's settings, the rom will do all that stuff
---------- Post added at 06:48 PM ---------- Previous post was at 06:45 PM ----------
Oh by the way you made way 3? You installed the custom rom? As a zip file? Like Cyanogen? And it took you back to recovery? What recovery do you have? And did you UNCHECK the signature check? IT'S VERY IMPORTANT
Click to expand...
Click to collapse
I installed Revolution HD as a zip file and i m using TWRP and yes it took me back. Zip file signature was and is unchecked. When i was installing the custom rom everything went fine with the installation of the custom rom.
And u mean with the settings F. Reset Time and other Stuff like that? And where should i put the stock rom? CSC or AP?
I tried with AP :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
By the way my downlaod settings are:
ODIN MODE
PRODUCT NAME: GT-I9300I (ist falsche rom. muss GT-I9301I)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
AnroidLover said:
I installed Revolution HD as a zip file and i m using TWRP and yes it took me back. Zip file signature was and is unchecked. When i was installing the custom rom everything went fine with the installation of the custom rom.
And u mean with the settings F. Reset Time and other Stuff like that? And where should i put the stock rom? CSC or AP?
I tried with AP :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> __XmitData_Write
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
By the way my downlaod settings are:
ODIN MODE
PRODUCT NAME: GT-I9300I (ist falsche rom. muss GT-I9301I)
CURRENT BINARY: Custom
SYSTEM STATUS: Custom
QUALCOM SECUREBOOT: ENABLE (CSB)
RP SWREV: S1, T1, R1, A1, P1
UDC START
Click to expand...
Click to collapse
Try to change cable usb
Alessandro's said:
Try to change cable usb
Click to expand...
Click to collapse
I tried. Failed again ! :crying::crying:
HELP ME PLEASE :crying::crying:
Alessandro's said:
Click to expand...
Click to collapse
That problem is omg. I dont know where the problem is :crying:
Alessandro's said:
Click to expand...
Click to collapse
Hey Jow, i got another usb cable. Now its says always Unknwon Device (also in Odin no added Message)