Hello. I've been getting a lot of emails on how to do that and i thought i should make a thread here.
Now you got to have the original box in which there is the imei written. I don't take any credit for this guide as i didn't write it but i found it somewhere here but it doesn't exist anymore. I'm not responsible for any damage may happen to your phone. I did it several times after flashing official 2.3.5.
It has worked fine with my IDEOS X5 U8800.
1. Tools
a. Drivers for U800 32bit win 7 (tested and work )
http://www.2shared.com/file/fnP5fc8G/u8800Drivers.html
b. Drivers for Android 32 and 64 bit win 7 (not tested )
http://www.2shared.com/file/ZNZ4Q0lk...012_09_12.html
c. Software for restore
http://www.2shared.com/file/xBxUOnPz/DFS.html
2. Enable debugging by USB in the settings.
In call type * # * # 2846579 # * # * http://postimage.org/image/tnj4s2dyj/
3. Go to ProjectMenu -> Background settings -> Usb port settings put the Manufacture mode and corfim.
4. Go again to ProjectMenu -> Background settings -> Qualcomm backround open settings put the background open. Password 0 and corfim.
5. Go again to ProjectMenu -> Background settings -> Log setting -> Log switch put log on and corfim.
6. Now conect your phone to pc and install the drivers.
You must see this at your device manager http://postimage.org/image/5lrm61agd/
7. Instal DFS and run.
8. Click Ports, select the port with the signature DBAdapter Reserved Interface (double click) to close.
http://postimage.org/image/3l3bmfyzr/
9. In the DM select Qualcomm.
http://postimage.org/image/6bmt1908z/
10) Press the SPC, the bottom will Device Unlocked.
11) Select Programming and in the IMEI write yours and press Write.
http://postimage.org/image/dmbp29q35/
13) Check Imei, may appear after a reboot, if not try a few more times to try to set the port speed to 115200 (box to the left of DM)
Check IMEI *#06#
As soon as the IMEI restored change:
* # * # 2846579 # * # * -> ProjectMenu -> Background settings -> Usb port settings to put on the Manufacture mode google mode (or normal if you do not get up google)
* # * # 2846579 # * # * -> ProjectMenu - > Background settings -> Qualcomm backround open settings put close
Good luck..
Thanks a lot... now I got my imei back. But now I have one another problem, I installed ics rom and now my wifi Mac id is 00:00:00:00:00:00. Are they related?
Sent from my U8800 using XDA Premium 4 mobile app
I don't think so. But I've already replied somewhere on how to fix mac address. Search
Sent from my U8800 using xda app-developers app
Didn't work for me
Cybergiannis said:
Hello. I've been getting a lot of emails on how to do that and i thought i should make a thread here.
Now you got to have the original box in which there is the imei written. I don't take any credit for this guide as i didn't write it but i found it somewhere here but it doesn't exist anymore. I'm not responsible for any damage may happen to your phone. I did it several times after flashing official 2.3.5.
It has worked fine with my IDEOS X5 U8800.
1. Tools
a. Drivers for U800 32bit win 7 (tested and work )
http://www.2shared.com/file/fnP5fc8G/u8800Drivers.html
b. Drivers for Android 32 and 64 bit win 7 (not tested )
http://www.2shared.com/file/ZNZ4Q0lk...012_09_12.html
c. Software for restore
http://www.2shared.com/file/xBxUOnPz/DFS.html
2. Enable debugging by USB in the settings.
In call type * # * # 2846579 # * # * http://postimage.org/image/tnj4s2dyj/
3. Go to ProjectMenu -> Background settings -> Usb port settings put the Manufacture mode and corfim.
4. Go again to ProjectMenu -> Background settings -> Qualcomm backround open settings put the background open. Password 0 and corfim.
5. Go again to ProjectMenu -> Background settings -> Log setting -> Log switch put log on and corfim.
6. Now conect your phone to pc and install the drivers.
You must see this at your device manager http://postimage.org/image/5lrm61agd/
7. Instal DFS and run.
8. Click Ports, select the port with the signature DBAdapter Reserved Interface (double click) to close.
http://postimage.org/image/3l3bmfyzr/
9. In the DM select Qualcomm.
http://postimage.org/image/6bmt1908z/
10) Press the SPC, the bottom will Device Unlocked.
11) Select Programming and in the IMEI write yours and press Write.
http://postimage.org/image/dmbp29q35/
13) Check Imei, may appear after a reboot, if not try a few more times to try to set the port speed to 115200 (box to the left of DM)
Check IMEI *#06#
As soon as the IMEI restored change:
* # * # 2846579 # * # * -> ProjectMenu -> Background settings -> Usb port settings to put on the Manufacture mode google mode (or normal if you do not get up google)
* # * # 2846579 # * # * -> ProjectMenu - > Background settings -> Qualcomm backround open settings put close
Good luck..
Click to expand...
Click to collapse
This procedure did not work for me. I found it a couple of weeks ago in another thread (http://forum.xda-developers.com/showthread.php?t=1591997) and gave it a try (numerous times) without success. I was able to complete all steps up until actually writing the new IMEI. I attempted to write it a couple of dozen times without any success. It appears to work but the lMEI never actually changes.
I also found another procedure using a program called NVedit but it would give me an error stating the NV location was set to read only (I forget the actually wording). It seems that my phone has the location that contains my IMEI locked in some way that nothing can change it. So I gave up on that phone and am using a different one that I bought on eBay, brand new at a dirt cheap price ($27.00).
pastorbob62 said:
This procedure did not work for me. I found it a couple of weeks ago in another thread (http://forum.xda-developers.com/showthread.php?t=1591997) and gave it a try (numerous times) without success. I was able to complete all steps up until actually writing the new IMEI. I attempted to write it a couple of dozen times without any success. It appears to work but the lMEI never actually changes.
I also found another procedure using a program called NVedit but it would give me an error stating the NV location was set to read only (I forget the actually wording). It seems that my phone has the location that contains my IMEI locked in some way that nothing can change it. So I gave up on that phone and am using a different one that I bought on eBay, brand new at a dirt cheap price ($27.00).
Click to expand...
Click to collapse
are you rooted? i remember having these issues when i flashed 2.3 after 4.2 rom. u first need ti flash 2.2 then 2.3 and that should work
Cybergiannis said:
are you rooted? i remember having these issues when i flashed 2.3 after 4.2 rom. u first need ti flash 2.2 then 2.3 and that should work
Click to expand...
Click to collapse
Yes, I am rooted.
I started out on 2.2 way back in the beginning. Then I flashed 2.3.5. That's when I lost my IMEI and replaced the phone.
But I wanted to keep experimenting at getting it working 100% even though I had a new working, rooted, and customized phone. Using 5IromToolBox I restored a backup from the new phone to the broken phone just to see if it would work. Then I flashed Stallion-51-ICS custom ROM. It is a GB based ROM with look and feel of ICS.
When I run the procedure in this thread, everything looks as though it has worked, but the IMEI never changes. So what did 5Irom do differently that it was able to restore the backup from a different phone but I cannot use DFS or NVEditor to write to the locations? The back I made from the new phone and restored to the old one is Consumer Cellular so I suspect they have locked something out that 5Irom is able to get around but other tools don't.
On another note, just for the heck of it I tried to upgrade to ICS from GB and it fails on the first update step. Go figure.
If I could find a full-flash procedure for the pro and 51 versions of this phone I suspect I could resolve all issues. Who knows?
UPDATE: I went through the whole process again and noted a point I forgot to mention. In DFS at the bottom of the screen EQF is yellow, not green. I don't recall exactly what that means but in reading through the DFS doc, it states that writing a new IMEI is not possible as long as EQF is yellow. When I enter my IMEI and click on the WRITE command the response is "MODECHANGE OfflineD OK"
pastorbob62 said:
Yes, I am rooted.
I started out on 2.2 way back in the beginning. Then I flashed 2.3.5. That's when I lost my IMEI and replaced the phone.
But I wanted to keep experimenting at getting it working 100% even though I had a new working, rooted, and customized phone. Using 5IromToolBox I restored a backup from the new phone to the broken phone just to see if it would work. Then I flashed Stallion-51-ICS custom ROM. It is a GB based ROM with look and feel of ICS.
When I run the procedure in this thread, everything looks as though it has worked, but the IMEI never changes. So what did 5Irom do differently that it was able to restore the backup from a different phone but I cannot use DFS or NVEditor to write to the locations? The back I made from the new phone and restored to the old one is Consumer Cellular so I suspect they have locked something out that 5Irom is able to get around but other tools don't.
On another note, just for the heck of it I tried to upgrade to ICS from GB and it fails on the first update step. Go figure.
If I could find a full-flash procedure for the pro and 51 versions of this phone I suspect I could resolve all issues. Who knows?
UPDATE: I went through the whole process again and noted a point I forgot to mention. In DFS at the bottom of the screen EQF is yellow, not green. I don't recall exactly what that means but in reading through the DFS doc, it states that writing a new IMEI is not possible as long as EQF is yellow. When I enter my IMEI and click on the WRITE command the response is "MODECHANGE OfflineD OK"
Click to expand...
Click to collapse
it should be green! what i would do is to flash 2.2 then 2.3.5 and follow again the steps very carefully! maybe u ever flashed a partition and it's not the default one? i can't really help you :/ try this and if it doesn't work make a thread in the q&a section
Cybergiannis said:
it should be green! what i would do is to flash 2.2 then 2.3.5 and follow again the steps very carefully! maybe u ever flashed a partition and it's not the default one? i can't really help you :/ try this and if it doesn't work make a thread in the q&a section
Click to expand...
Click to collapse
Yeah, I knew that it should be green. The bottom line is I do not have the 2.2 image to flash. I would have done that a long time ago if I had it. All I have is the DiskImage backup that I made off of my new phone. When I flashed it onto the old phone it starts, displays the Consumer Cellular logo for about ten seconds then shuts off immediately. As far as starting a thread in Q & A, I did that weeks ago and got nowhere fast.
Any link I have found for the original 2.2 for -51 and pro is usually a broken link. or it takes me to download that stupid iLivid program that doesn't do squat to get the files I need. I did find a DiskImage file that somebody made and posted but it is almost 4 gig in size. You are supposed to use Pink Screen to load it but Pink Screen only gives me access to the image directory and it's only 256 meg.
Thank you for your time and suggestions.
I believe in the wiki section there are links to default 2.2 and 2.3.5. The ones I found a long time ago were from Blefish, although I'm not sure. Good luck!
Sent from my U8800 using xda app-developers app
Dead link.
Hi.
I try to download the "Drivers for Android 32 and 64 bit win 7 (not tested )", but its a dead link. I run win7 pro, and somehow the 32 bit driver doesn't work.
Would like to try the 64 bit driver. Could u reupload it, please?
I just did a repost cause i veen asked a lot of times I don't have the files and I don't thinks drivers are needed. You could just install huawei's suite for PC
Sent from my U8800 using xda app-developers app
WORKS!!!!
Cybergiannis said:
I just did a repost cause i veen asked a lot of times I don't have the files and I don't thinks drivers are needed. You could just install huawei's suite for PC
Sent from my U8800 using xda app-developers app
Click to expand...
Click to collapse
YEY!!!!!!! It worked!!!!
Update the first post with this info so others dont have to struggle like I did.
Thanks a bunch!!! :victory:
ευχαριστω πολυ----thanks man
Hi All,
Many thanks for this post.
Iv recently installed the Blefish CM11 rom for U8800 and its works fine. Only issue I have is IMEI=0. I can make and receive calls and even use the mobile internet.
My question is - Is there a way to edit the IMEI no on KK4.4.2 ROM through entering in the engineering mode?
or else, will have to start from the beginning (stock rom process as mentioned in the OP).
thanks for your help.
mohammad.nomaan said:
Hi All,
Many thanks for this post.
Iv recently installed the Blefish CM11 rom for U8800 and its works fine. Only issue I have is IMEI=0. I can make and receive calls and even use the mobile internet.
My question is - Is there a way to edit the IMEI no on KK4.4.2 ROM through entering in the engineering mode?
or else, will have to start from the beginning (stock rom process as mentioned in the OP).
thanks for your help.
Click to expand...
Click to collapse
i have no idea. my guess is that u should try
Cybergiannis said:
i have no idea. my guess is that u should try
Click to expand...
Click to collapse
Hi,
I haven't found out the way to fix it yet.
Only way I got to fix is to redo the stock rom, root, save the imei and the reflash the custom rom.
The reason for the imei issue was changing the partitions
thnx anyways
this guide that you have post it has been made by me and at least you should have say that is ported from me. Even the links that you have are in my acount. YOU ONLY COPY MY POST . you could ask me to repost it or just mention me. Check this link http://forum.xda-developers.com/showthread.php?t=1876501
Related
I'm not responsible for what might happen on your phone if you choose to dial any of these!
These are the codes that work on the standard phone dialler app on the Orange San Francisco, but I'm pretty sure they'll be almost identical on other models that we collectively know as "ZTE Blade". Known small differences (in texts) are down to whether the firmware expects to be running on an OLED or TFT display, and whether you've deleted seemingly unused apps like ChiperTest.apk, fcctest.apk and QcNvTest.apk. Most are prefixed with "*983*", which is "*ZTE*" in phone letters -- I've added a mnemonic for the other part where I think it's obvious (feel free to suggest better ones!).
"Automatic Inspection" runs through the basic tests automatically (usually you need press a button to move on to the next bit -- don't get thrown by any blank colour test screens!). There are a number of interesting items for developers, with hardware info and other goodies. If any of the descriptions don't make the function obvious then it's either poorly written or I don't know exactly what it does (I'll happily update this if others can explain better).
If the code has been recognised by the dialler then it will react immediately when you enter the final "#". If nothing happens when you've done that, don't press Dial!
Edit: on the ROMs based on the Japanese 2.2 you need to put the phone into "Engineering Mode" first, by dialling *ZTE*OPENEM# (*983*673636#) -- this action will be confirmed by a quick pop-up. To close this mode, dial *ZTE*CLOSEEM# (*983*2567336#) -- this then prompts whether you want to do a Factory Reset, which you do not have to do (you can simply Back away from this screen).
Dial Mnemonic Operation
*983*0# Menu (20:Battery/OLED/Back Light/Vibrator/Ringer/LED/Key/OLED off/SD/BT address/Radio Info/Memory/TouchPaint Test/Audio Loop/FM/Camera/GPS Test/IMEI/IMSI)
*983*3640*01# IMSI
*983*25# Battery Info[/COLOR]
*983*31# OLED Test
*983*26# Backlight Test
*983*850# Radio Test 0
*983*86# Vibrator & LED Test
*983*84# Ringer Test
*983*07*01# Headset Test
*983*07*02# Key Test
*983*3470# LCD Test
*983*81# SD Test
*983*890# -
*983*26*# Radio Test 1
*#06# IMEI
*983*27274# CRASH Reboot
*#08# Test Flag [Note: requires QcNvTest.apk in /system/app]
*#09***# BT Test
*983*1275# _ASK Dev Info
*983*7# Menu (4:Version/IMEI/IMSI/BT address)
*983*3640# DOH+ Phone Info (inc ping test, radio on/off)
*983*636# MEM Memory Test
*983*28# BT Emode BT Test
*983*477# GPS GPS Test
*983*21# Audio Loop Test
*983*70# Automatic Inspection
*#18# LED Test
*#19# TouchPaint Test
*983*36# FM FM Test
*983*57# Factory Reset
*983*473# Camera
*#23# Video Camera
*983*10# Delete (Touchscreeen) Calibration File
*#25# FM Test
*983*2726# SIM Contacts Op 1
*983*37# SIM Contacts Op 2
*983*6726# SIM Contacts Op 3
*983*154# "test" Menu (12:Self-starting/Software
Version/Hardware Version/PSN/Test Flag/[Completed]/Board Serial/Bluetooth
Address/SMS security/SMS Registration Status/Flash Type/PRL Version/Serial Configuration)
*983*07# Menu (9LED/Ringer/Vibrator/Key Test/Audio Loop/Headset Test/FM/Camera/SD)
*983*5182# Dev Info
*983*7469# SHOW Automatic Inspection
*#26***# Sensor Test
*983*7936# QXDM Save Qxdm in log system
*987*0# Menu (4roduce Information[->"test" Menu]/Automatic Inspection/Factory data reset/Battery information)
*#27***# Compass Test
*983*87274# USBSI USB Switch Test
*983*06# BT Test
*983*564738# LOGSET LOG Set (inc sys_rw)
*983*93# FCC Test [Note: requires fcctest.apk in /system/app]
*983*2377# CFQP Call Forwarding Query with PowerOn
*983*24474636# CHIPINFO Chiper Test (chip info) [Note: requires
ChiperTest.apk in /system/app]
*983*29873283# AXUPDATE Touchscreen Updater
*983*73564# SDLOG SD Log
Note: the above are for the standard ROM (well, apps) running 2.1. The current Froyo ROM (with standard dialler, etc.) does not have the Touchscreen Updater, but adds:
Dial Operation
*987*123456# DM Test
IN modaco
Hello, what code shude I use to know if my SF is TFT or Amoled?
Regards!
Check the build number in Settings>About Phone. AMOLED ends in 05, LCD ends in 08. IIRC all white SF models are 08 and most grey are 05 (unless its a newer unit which will likely be 08).
Thank´s man.
Mine is 01. What that means?
Looking at the screen characteristics it seems like LCD.
Thanks man. great post
Really nice. Works on Boost Mobile Warp Sync N9515.
Would you happen to have a code that forces prompt for unlock? (Changing sim cards doesn't trigger anything)
same here... up for this....
No Boost Mobile ZTE Warp Sync N9515 Unlock Screen
chinnyss said:
same here... up for this....
Click to expand...
Click to collapse
I think unlocking the Boost Mobile is a lost cause. I've tried several other sims and the only codes I've found to show the unlock menu don't work:
1) Alright then please remove the SIM card and try this code ###825*09#,
2) Got the prompt for code? Please enter the code you received,
3) Failed above, try *983*8284# to access the Unlock Menu,
4) Failed above, finally try *983*865625# to access the Unlock Menu.
zte warp elite n9518 rooted but still i can't use MSL reader or alogcat it says in root checker verify root congrats and after rebooting i got to root again please help just need to get SPC and or MSL code
You the MAN! THA KS.
kelvinpacquette said:
zte warp elite n9518 rooted but still i can't use MSL reader or alogcat it says in root checker verify root congrats and after rebooting i got to root again please help just need to get SPC and or MSL code
Click to expand...
Click to collapse
Can u tell me rhat what do i need to enable usb debigging or adb mode ?? I have to connect my zte z982 device to miracle sodtware, but unable to connect because frp lock.
I cant enable usb debugfing
techeligible3322 said:
Can u tell me rhat what do i need to enable usb debigging or adb mode ?? I have to connect my zte z982 device to miracle sodtware, but unable to connect because frp lock.
I cant enable usb debugfing
Click to expand...
Click to collapse
Edit: on the ROMs based on the Japanese 2.2 you need to put the phone into "Engineering Mode" first, by dialling *ZTE*OPENEM# (*983*673636#) -- this action will be confirmed by a quick pop-up. To close this mode, dial *ZTE*CLOSEEM# (*983*2567336#) -- this then prompts whether you want to do a Factory Reset, which you do not have to do (you can simply Back away from this screen).
Dialing the first set of numbers made it possible for me to turn on abd....
Sent from my SM-G550T using Tapatalk
Alright
paigesdavis1996 said:
Edit: on the ROMs based on the Japanese 2.2 you need to put the phone into "Engineering Mode" first, by dialling *ZTE*OPENEM# (*983*673636#) -- this action will be confirmed by a quick pop-up. To close this mode, dial *ZTE*CLOSEEM# (*983*2567336#) -- this then prompts whether you want to do a Factory Reset, which you do not have to do (you can simply Back away from this screen).
Dialing the first set of numbers made it possible for me to turn on abd....
Sent from my SM-G550T using Tapatalk
Click to expand...
Click to collapse
Thank you for your reply
How did you enter / enable adb? I have a 971 and the 2nd code from your site doesn't work, I am able to enable eng. mode
I also tried the connect to computer in control panel and that doesn't do anything either.
Frp locked
Trick
techeligible3322 said:
Thank you for your reply
Click to expand...
Click to collapse
This worked for me and I have the ZTE z blade max thank you
Has this been proven to root the phone yet ? Please leave feedback .
Good News
#Starlord37# said:
This worked for me and I have the ZTE z blade max thank you
Click to expand...
Click to collapse
That's very good to know you are welcome
I haven't had a chance to try it fully yet as I have been trying to root my girlfriends Moto e4 with magisk which I will probably have done by the end of the night and then I plan to tackle my z982 will keep you posted though
Hi,
since a week or so my u8800 suffers from a huge battery drain.
Today i just got 10hours out of it and almost did nothing. (4min. phone call/ 10messages/ max. 10min surfing)
The last 10% of battery was gone in 30 seconds.
It all started last week when my phone was on stock 2.2. Then i updated to the latest stock 2.3.5, but still the same problem.
Model number : u8800
Android version : 2.3.5
base band version : 404020
Kernel version : 2.6.35.7-perf [email protected]#1
Build number : U8800V100R001C00B528G001
I also wanted to calibrate the battery, but i can't root the phone. Tried every program out there
Anyone got the same problem or has a solution ?
Hello Kawadude,
I use superoneklick and it works fine to root the device. Hier ist the how to, what you must do before use superonklick:
- Dial * # * # 2846579 # * # *
- Go to projectmenu, background settings, log settings, log switch and set Log on
- Reboot phone
- Set USB debugging on
- Run superonklick http://depositfiles.com/files/n0dcxce3t or http://shortfuse.org/
Hope it helps
Already tried that without a result.
I also tried DooMLoRD v4, Unlock Root and One-click Root.
Since i installed the official 2.3.5 i can't root my device annymore. On stock 2.2 this wasn't a problem.
Hello, do you keep wi fi enabled at all times? i noticed my battery drains increased greatly when i leave my wifi on 24/7
No, wifi is only enabled when I'm at home.
A couple of weeks ago the battery life was just fine. (With the same usage)
Kawadude said:
No, wifi is only enabled when I'm at home.
A couple of weeks ago the battery life was just fine. (With the same usage)
Click to expand...
Click to collapse
Close any application in your pc that might try to connect with an android device (like huawei's or Asus PC Sync, etc). Those applications use the adb driver and block superoneclick. Check if windows recognize your device and install it properly. Hum... That's all I can think of... ;-)
Igory0k said:
1.Settings-> Applications -> Developer Tools-on
2.Unknown sources -> Settings-> Applications -> Unknown sources-on.
3.Fast boot -> Settings-> Applications-off
4.Dial: *#*#2846579#*#*
5. Go to projectmenu > background settings > log settings > log switch > set Log on
6.log setting-dump & log-on
7.Reboot Phone
Download B528_ROOT
8. Run B528_root.bat
9. Your phone should now be Rooted.
10. You can now go back *#*#2846579#*#* and turn logging off if you want.
Click to expand...
Click to collapse
Try this. I did hear that this last release from huawei (B528) couldn't be/was really hard to get rooted. I haven't tried this, just found it. Credit to @Igory0k.
MtG92 said:
Try this. I did hear that this last release from huawei (B528) couldn't be/was really hard to get rooted. I haven't tried this, just found it. Credit to @Igory0k.
Click to expand...
Click to collapse
Didn't work for me.
The phone rebooted and freezed at the huawei logo.
The only thing i didn't find is step 6: "6.log setting-dump & log-on"
Kawadude said:
Didn't work for me.
The phone rebooted and freezed at the huawei logo.
The only thing i didn't find is step 6: "6.log setting-dump & log-on"
Click to expand...
Click to collapse
You have to do it, rooting apps need that option
And launcher apps etc. don't install them, your battery won't drain Uninstall unnecessary apps too
Moved To Q&A
Please post all questions in the Q&A section
After so many chinese roms testing my roms making custom roms..installing beta roms...and any kind of rom...i lost my IMEI so after i try everything i send it to service so im without phone and its easter holidays here on greece...You will find many posts here who to backup your IMEI but i will make this one so if a Admin can make it sticky so noone will have any more problems...
Caution if you havent took your IMEI backup do it and keep your backup like a treasure..you can't flash your IMEI if you loose it and you have to go to service to change your board!!
1)Download 5iromtoolbox: http://pikachukaki.googlecode.com/files/ToolBox5iromV1.0.4.2.apk
2)Open the app
3)Press backup IMEI
4)Connect your phone with USB cable and go to your pc
5)Open your sd card through windows explorer or whatever you use
6)Seek the folder /sdcard/5irom/imeibackup/
7)Copy the imeibackup folder to your pc to a folder that you will not by accident format ^_^
8)You are ok...now you can make whatever you like...
To restore your IMEI
1)Take your imeibackup folder from your pc
2)Paste it on your sd card on folder /sdcard/5irom/imeibackup/
3)Open the 5iromtoolbox
4)Press Restore IMEI and restart your phone!!
Just take it..is very important so you will not have to send your phone to service!!H
Hope i help!!
--------
Solution to flash your lost imei!
1) Enable debugging by USB in the settings
2) * # * # 2846579 # * # * -> ProjectMenu -> Background settings -> Usb port settings put the Manufacture mode. (Most likely it is already selected, then select Normal mode and re-manufacture mode)
3) * # * # 2846579 # * # * -> ProjectMenu -> Background settings -> Qualcomm backround open settings put the background open. Password 0
4) Install the DFS DFS_3.3.0.7.exe (1.99 MB) Number of downloads: 5
, connect your phone to your computer.
5) will be found new hardware (multiple devices). You need to install drivers DBAdapter_Reserved_Interface.zip (60.41 KB) Number of downloads: 4
on the device vid_12d1 & pid_1035 & mi_04 (Open Device Manager, right-click on the device properties -> Information -> ID equipment). The equipment is established as a COM port.
5) Run the DFS, click Ports, select the port with the signature DBAdapter Reserved Interface (double click) to close.
6) Press the SPC, the bottom will Device Unlocked.
7) In the DM to select Qualcomm.
8) Back the tab Programming, in a field to enter your IMEI IMEI, then click the Read and Write Status.
9) Check Imei, may appear after a reboot, if not try a few more times to try to set the port speed to 115200 (box to the left of DM)
As soon as the IMEI restored change:
* # * # 2846579 # * # * -> ProjectMenu -> Background settings -> Usb port settings to put on the Manufacture mode google mode (or normal if you do not get up google)
* # * # 2846579 # * # * -> ProjectMenu - > Background settings -> Qualcomm backround open settings put close
If someone has 0 IMEI and havent found another way to fix it could try this and tell us if its working!!
Write your IMEI and your IMEI only!!!
Pikachukaki> why you not answering me in private question? i'm not for fight, just interesting
Sent from my ragelis
bronxitas said:
Pikachukaki> why you not answering me in private question? i'm not for fight, just interesting
Sent from my ragelis
Click to expand...
Click to collapse
There is nothing to answer you...you send me your opinion and its ok...you said you found duplicates...go yel [email protected]!!my rom working properly...so thats ok with me!!if you don't like it you can use official huawei!
Does this work for the u8800 to? the not pro version xD
theminikiller said:
Does this work for the u8800 to? the not pro version xD
Click to expand...
Click to collapse
Yeah...i think its 99% universal for all android phones!!not quite sure cos samsung stores IMEI on a folder that we don't have!!
ok ty, then ill do it now xD
Thanks! I just tried to backup my IMEI on my U8800 and it worked good. Don't know about restore though yet. I hope I won't need to...
thanks!!
What am i doing wrong?
My phone is Chinese and
it's rooted with SuperOneClick.
When backing up IMEI 5irom
(after granting superuser permission)
6 seconds later,
the folder /sdcard/5irom/imeibackup/
is empty.
and when starting 5irom again
the IMEI Backup dispays:
IMEI not backed up yet.
What am i doing wrong?
Also how many and
what files should be inside
the /imeibackup/ folder?
Any info would be greatly appreciated.
ff
ffinder said:
My phone is Chinese and
it's rooted with SuperOneClick.
When backing up IMEI 5irom
(after granting superuser permission)
6 seconds later,
the folder /sdcard/5irom/imeibackup/
is empty.
and when starting 5irom again
the IMEI Backup dispays:
IMEI not backed up yet.
What am i doing wrong?
Also how many and
what files should be inside
the /imeibackup/ folder?
Any info would be greatly appreciated.
ff
Click to expand...
Click to collapse
check your sd card cos if you haven't one it make the folders on internal but it didn't save anything!!after successfully saves imei it gives you 4 folders and one that says imei has 4 *.img files in it!!
5IromToolBox
When i clicked IMEI Backup
message is that
"back fail,check your root privileges! "
Details Of My Device Is:
Model number : u8800 pro
Android version : 2.3.5
base band version : 404020
Kernel version : 2.6.35.7-perf [email protected]#1
Build number : U8800PV100R001C213B519
ffinder said:
My phone is Chinese and
it's rooted with SuperOneClick.
When backing up IMEI 5irom
(after granting superuser permission)
6 seconds later,
the folder /sdcard/5irom/imeibackup/
is empty.
and when starting 5irom again
the IMEI Backup dispays:
IMEI not backed up yet.
What am i doing wrong?
Also how many and
what files should be inside
the /imeibackup/ folder?
Any info would be greatly appreciated.
ff
Click to expand...
Click to collapse
does it have mtk based cpu? this won't work on it, but there's another procedure for that..
hi
i used this tool on my Mi410 which is a variant of U9000 and i have the folder called
the folder /sdcard/5irom/imeibackup/ totally 4 files assuming this means i have sucessfully backup my imie
haree said:
hi
i used this tool on my Mi410 which is a variant of U9000 and i have the folder called
the folder /sdcard/5irom/imeibackup/ totally 4 files assuming this means i have sucessfully backup my imie
Click to expand...
Click to collapse
Me too, i think it's all ok, but I have only 3 files with Aurora ROM: 10.img 11.img 5.img. I upload that files to my DropBox too.
haree said:
hi
i used this tool on my Mi410 which is a variant of U9000 and i have the folder called
the folder /sdcard/5irom/imeibackup/ totally 4 files assuming this means i have sucessfully backup my imie
Click to expand...
Click to collapse
you need 3 imgs on imei folder....
my imei is already zero will it work with me
efray said:
my imei is already zero will it work with me
Click to expand...
Click to collapse
if you didnt get backup your phone no...now your screwed you need to go to service for board change!!im sorry!
so if i didnt is there anything dangerous
i asked coz i dialed customer service of my network they ask for the imei as they didnt see it
thanx for 4 cooperation
efray said:
so if i didnt is there anything dangerous
i asked coz i dialed customer service of my network they ask for the imei as they didnt see it
thanx for 4 cooperation
Click to expand...
Click to collapse
the phone didnt work normally without imei...when i lost mine wifi didn't work and i couldn't install official rom!!
when i was on aurora imei was zero but i installed official ics successfully
wifi data and all othe functions works great i cant see any difference
and i rooted the phone successfully
wat i wana ask is there any risk of loosing my phone
thnx
Hello,
To start off, I have a USCellular S4 w/ CM10.1, currently the 7/9 nightly. I am running baseband version R970VXUAMDL and have not modified the kernel.
I am unable to enable WiFi at all on CM10.1 and haven't been able to since initially flashing CM10.1.
Under the Settings menu, I am unable to enable WiFi - it's greyed out.
Under the WiFi menu, I can enable the toggle but it does nothing.
Under the Advanced menu, MAC address shows 'unavailable' and the Wi-Fi region code is set to 'Europe' and will not remember changes.
sylvisj said:
Hello,
To start off, I have a USCellular S4 w/ CM10.1, currently the 7/9 nightly. I am running baseband version R970VXUAMDL and have not modified the kernel.
I am unable to enable WiFi at all on CM10.1 and haven't been able to since initially flashing CM10.1.
Under the Settings menu, I am unable to enable WiFi - it's greyed out.
Under the WiFi menu, I can enable the toggle but it does nothing.
Under the Advanced menu, MAC address shows 'unavailable' and the Wi-Fi region code is set to 'Europe' and will not remember changes.
Click to expand...
Click to collapse
Have you tried removing the .cid.info file ?
Using a terminal app type the following:
Code:
su
rm /data/.cid.info
On some ROM's have have to do this after every time I have rebooted the phone, not quite sure why but it works for me.
TrallaP said:
Have you tried removing the .cid.info file ?
Using a terminal app type the following:
Code:
su
rm /data/.cid.info
On some ROM's have have to do this after every time I have rebooted the phone, not quite sure why but it works for me.
Click to expand...
Click to collapse
Hello,
Thanks for the suggestion. I fired up Terminal Emulator, su'd, and it doesn't look like there is a .cid.info in /data/. There is a .psm.info, though, and .npswifi_stream - I don't know if they're related at all.
sylvisj said:
Hello,
Thanks for the suggestion. I fired up Terminal Emulator, su'd, and it doesn't look like there is a .cid.info in /data/. There is a .psm.info, though, and .npswifi_stream - I don't know if they're related at all.
Click to expand...
Click to collapse
Here's the 'ls -a' output for /data:
Code:
[email protected]:/data # ls -a
.container_1
.container_2
.container_3
.layout_version
.mtp_stream
.npswifi_stream
.pcsync_stream
.psm.info
.socket_stream
.ssh
anr
app
app-asec
app-lib
app-private
audio
backup
bcmnfc
bluetooth
cam_socket0
cam_socket1
container
dalvik-cache
data
dontpanic
drm
fota
hostapd
local
log
lost+found
media
misc
nfc
property
qcks
radio
resource-cache
security
shared
ssh
system
time
tombstones
user
wiper
wpstiles
Bump.
I have the same problem......
ninne1 said:
I have the same problem......
Click to expand...
Click to collapse
Bump again.
i think it's missing IMEI and EFS. Try this http://forum.xda-developers.com/showthread.php?t=1264021
r47z said:
i think it's missing IMEI and EFS. Try this http://forum.xda-developers.com/showthread.php?t=1264021
Click to expand...
Click to collapse
I dunno about EFS, but I know the IMEI is already correct - *#06* is showing the same IMEI as the label on the back of my phone.
My phone is work well after flashing CM, but no WIFI.
No /data/.cid.info file!
*#06# - show IMEI.
Did we ever get to the bottom of this?
Im having exactly the same problem, so bump. Its been like that for 6 months, my workaround so far was getting a bigger data subscribtion since 4g is working fine
sylvisj said:
Hello,
To start off, I have a USCellular S4 w/ CM10.1, currently the 7/9 nightly. I am running baseband version R970VXUAMDL and have not modified the kernel.
I am unable to enable WiFi at all on CM10.1 and haven't been able to since initially flashing CM10.1.
Under the Settings menu, I am unable to enable WiFi - it's greyed out.
Under the WiFi menu, I can enable the toggle but it does nothing.
Under the Advanced menu, MAC address shows 'unavailable' and the Wi-Fi region code is set to 'Europe' and will not remember changes.
Click to expand...
Click to collapse
Hi sylvis,
I realize that this is an old post. However. perhaps this thread will help someone else:
I flashed a Samsung Galaxy S4 (T-mobile SGH-M919) to CyanogenMod (CM11) this weekend. It worked ok for a couple days. The owner then said that they can't get any WI-FI. I found your post here and read with optimism that I might be able to fix this problem. Our problem was exactly "word for word" the same problem as you described in your original post. (Well almost exactly; we couldn't get "USA" to stick as the region code)
Before flashing the phone, I did install Philz ClockworkMod and did do a backup of the OEM ROM before flashing to CM11. That said, I found that I did not have to go down the road of restoring a missing IMEI file (as other threaders here describe). Here's what worked for me:
I dialed *#06# on the phone to see if there was an IMEI number present, and there was. I wrote down that number. So I decide to see if that number matched the printed number on the phone, that we can find under the battery.
Before I do a power off of the phone, I recall that I had turned OFF both Bluetooth and Mobile Networks. WI-FI was still turned ON, but in it's non-functional "greyed out" state like you and I both experienced.
Now I power off the phone, take off the back cover, and take out the battery to have a look at the printed IMEI number. Yes, it does march the number that I saw via *#06#.
I had to get up to do something, then returned a couple minutes later. I popped in the battery and restarted the phone. To my utter surprise, WI-FI was back up! In "Advanced" I now see the MAC address and the region is locked on USA
I turn on Mobile Networks, and WI-FI's still working. Being the fool that I am, I have to test this further. So I power off the phone again and just let it sit there for a couple minutes. I power back on and there is still JOY. Problem resolved and happy customer.
In closing: I don't think that the removal and reinsertion of the battery was the total solution, because the owner had already tried that. However, the owner did not let the phone sit with the battery removed for very long. They just popped it out, waited a couple seconds, then popped it back in. I think the total solution was having WI-FI enabled, Bluetooth and Mobile disabled, then doing a power off, with an extended wait time before reinserting the battery.
Hope that helps.
Regards,
Brcobrem
WORK IN PROGRESS.. UNTIL NOW NOT GETTING 100%
This was for CM11s, Don't try on CM12s
As soon as we found right procedure we'll Update here
This tutorial is not for newbies.. If you are not little advance user don't do this
After reboot Values reset to Orignal setting (Reset)
need to prevent NV recovery
1. Download Files Here containing all the necessary files and extract it on desktop.
2. Enable Android Debugging on your phone and connect it to your computer,
3. Open up ADB and type the following:
Code:
adb shell
su
setprop sys.usb.config diag,adb
4. Launch Device Manager go to & expand Other Devices,
Right click Android (or something related) listed under that menu
Choose Update Driver Software,
Browse my computer for driver software,
Let me pick from a list of device drivers on my computer,
Just Click Next,
Have Disk,
Browse to where you extracted YU Diagnostics Driver folder
Inside you will find 32bit and 64bit versions, pick one as per your OS
Select htcdiag.inf (for 32bit) or HtcUsbMdmV64.inf (for 64bit) file that you will Open.
Accept all warning messages and let the installation of the driver complete.
5. Once everything is done installing, under Modems or Ports (Com & LPT) in Device Manager you will find HTC USB Modem.
Right click and select Properties; in this you will see Port: COM<number>. Remember that COM<number> or write it down.
6. Open QPST v2.7 Build 4.11 > run as administrator setup.exe (Don’t run QPST.2.7.411.msi)
7. Open QPST Configuration from Start Menu,
Go to the Ports tab,
Click on Add New Port (right bottom corner);
In the Port field type in the COM<number> you wrote down/remembered from step 5 and in Port Label type YU and finally click OK (left bottom corner).
If you've followed all the steps correctly until here, you should be able to see something like this in the Active Phones tab:
View attachment 3258366
Keep QPST Configuration window open
8. Open QXDM-3.12.714 > run as administrator setup.exe (Don’t run QXDMInstaller.msi)
9. Open QXDM Professional (run as administrator),
go to Options menu,
Select Communications
Set Target port to your phone COM<number> you wrote down/remembered from step 5 from dropdown list, Press OK.
View attachment 3258367
10. Back to QXDM main window, in the "View" drop-down menu, selects NV Browser
View attachment 3258368
now the fun part begins
View attachment 3259381
Put check mark on Dual SIM (as shown above SS) for apply all setting to both SIMs (Thanks to @tirta.agung)
11. Inside the NV Browser window,
Scroll down and click on line 01877 (rf_bc_config)
Click the Read button save original value in notepad in case something goes wrong.
Replace Input value with 3460734838925427584
Click on Write button.
12. Inside the NV Browser window,
Scroll down and click on line 00946 (band_pref_16_31);
Click the Read button, save original value in notepad in case something goes wrong.
Replace Input value with 0x0FF8 (please don't be an idiot and don't edit the empty one with "nam" in the name)
Click on Write button.
13. Inside the NV Browser window,
scroll down and click on line 02954 (band_pref_32_63);
click the Read button, save original value in notepad in case something goes wrong.
replace Input value with 805765120 (please don't be an idiot and don't edit the empty one with "nam" in the name)
click on Write button.
14. Inside the NV Browser window,
scroll down and click on line 00441 (band_pref);
click the Read button, save original value in notepad in case something goes wrong.
replace Input value with 0x380 or 0xFFFF (please don't be an idiot and don't edit the empty one with "nam" in the name)
click on Write button.
If you have problem with selection, you can edit it directly from your phone: *#*#4636#*#* /Phone information /Menu /Select radio band > Automatic
15. Inside the NV Browser window,
scroll down and click on line 06828 (lte_bc_config);
click the Read button, save original value in notepad in case something goes wrong.
replace Input value with 1904863 (please don't be an idiot and don't edit the empty one with "ext" in the name)
click on Write button.
16. Now Close QXDM; Wait 30 seconds,
disable Android Debugging on your phone,
unplug it and reboot your device;
Once it comes back on, it might take a minute or two for it to acquire signal so don't panic.
DO this on your own risk.. No body is responcible for any lost
Conclusion:
The only real way to know if the whole thing got applied is to do steps 1 through 10 again (obviously skipping installations)
and reading all values or if you are in an area where you previously had bad or no reception.
You can see unlocked GSM/UMPTS bands from the *#*#4636#*#* /Phone information /Menu /Select radio band
For more features of QXDM i.e. recover lost IMEI or ESN go HERE (Thanks to @tirta.agung)
Credits:
Thanks to @BlackSoulxxx for his original work with the Qualcomm baseband software, for the modified Drivers and for the LTE NV values
Thanks to @olokos for his original tutorial
Thanks to @devilsshadow for his original tutorial
Thanks to @Albirew for his original tutorial
Thanks to @tirta.agung for bringing the original thread to my attention & Guide me in many ways
Thanks to @fards for finding the diagnostics command that made all this possible
Thanks to @hem12 who raised my will for finding these tutorials.
Thanks to @d3athwarrior for post this tutorial.
Reserved
Don't forget to put check marks on dual sims, and apply all settings to sim0 and sim1 (see attachment). By the way before u messed things up, back up your modemst1, modemst2, fsc, and fsg.
By the way we can also use qxdm to recover lost imei, just go to 0550, and insert your imei for SIM 1 (sim0 in qxdm) and SIM 2 (sim1 in qxdm), for example:
Code:
If your IMEI was: 954091051099226, then the boxes would look like so:
8
9a
45
90
1
15
90
29
62
or also recover lost esn (item no 0 and 5597) or meid (1943 and 5598).
Great guide, guys !:good::good::good:
---------- Post added at 04:02 AM ---------- Previous post was at 03:59 AM ----------
Some error down there: "OPO" and huge load of credited people that seem dont fit in here. Clearly copied from OPO thread?
BlackSoulxxx said:
Great guide, guys !:good::good::good:
---------- Post added at 04:02 AM ---------- Previous post was at 03:59 AM ----------
Some error down there: "OPO" and huge load of credited people that seem dont fit in here. Clearly copied from OPO thread?
Click to expand...
Click to collapse
Yes you'r right.. I don't want to leave anyone in credit for them work :good:
OPO removed :Hawkeye:
but that works for me..
Need help for prevent NV recovery from you all
If it's the same as the 1+1, replacing /system/bin/rmt_storage with a version not locked would prevent nv recovery (do you know if NV values were sticking in an older version? If so, take it's rmt_storage and try to replace current one with older one, I think it's worth trying)
Albirew said:
If it's the same as the 1+1, replacing /system/bin/rmt_storage with a version not locked would prevent nv recovery (do you know if NV values were sticking in an older version? If so, take it's rmt_storage and try to replace current one with older one, I think it's worth trying)
Click to expand...
Click to collapse
Hmmm, as far as I know, all NV settings, including IMEI, or MEID, ESN, etc, resides in your modemst1 and modemst2 partition. If you don't believe me and eager to try, first make a backup of those two partitions, then format or wipe the two partition inside your phone (use fastboot to do this), I'll bet for your YU, now your IMEI and NV settings are all gone.
To be honest, I just found out from this thread that there is an rmt_storage in CM phones, wkwkwkwkw, . If the rmt_storage function is trough, then CM is locking the phone NV settings from the HLOS side not Non-HLOS side. I'll do some research on this rmt_storage.
Need Help from your side
tirta.agung said:
Don't forget to put check marks on dual sims, and apply all settings to sim0 and sim1 (see attachment). By the way before u messed things up, back up your modemst1, modemst2, fsc, and fsg.
.....
or also recover lost esn (item no 0 and 5597) or meid (1943 and 5598).
Click to expand...
Click to collapse
BlackSoulxxx said:
Great guide, guys !:good::good::good:
Some error down there: "OPO" and huge load of credited people that seem dont fit in here. Clearly copied from OPO thread?
Click to expand...
Click to collapse
Albirew said:
If it's the same as the
.....
current one with older one, I think it's worth trying)
Click to expand...
Click to collapse
Now current status is
when I connect mobile
it shows me like that
Even I change USB config to diag,adb
thru ADB or manually
this time its present in default.prop
I try both
trying to disable MTP in mobile USB connection is not working
Window for Settings > Storage > 3dot > USB computer connection is working
but when I disable MTP.. its not working3
So need help from your side..
how I enter / install diag mode
@tirta.agung
I read your complete Guide regarding unbrick YU
but as that post has multipal guides ... I little confused ..
Sorry I am Xtreme noob for all that
Can you guide me an easy way to connect with QPST for enable LTE band
Can I try
Guide #3. REVIVING YOUR IMEIs (That for 32bit or 64bit)??
for connect QXDM
ekhasti said:
@tirta.agung
I read your complete Guide regarding unbrick YU
but as that post has multipal guides ... I little confused ..
Sorry I am Xtreme noob for all that
Can you guide me an easy way to connect with QPST for enable LTE band
Can I try
Guide #3. REVIVING YOUR IMEIs (That for 32bit or 64bit)??
for connect QXDM
Click to expand...
Click to collapse
Yes use guide number three, and download the necessary file there. By the way, to use the guide you have to be in stock CM kitkat.
How to use these tools for Xperia C6602
Long story short, did it work in the end for more than 1 person?
thanks for the post. but i have a Lollipop rom. I will wait for you to update the thread ....
Can we try this in lollipop??? Is there any update on this???
ekhasti said:
WORK IN PROGRESS.. UNTIL NOW NOT GETTING 100%
CM12s
As soon as we found right procedure we'll Update here
Click to expand...
Click to collapse
Hi there, attached is boot.img and a hack rmt_storage for CM 12.1. Just flash the boot.img to your phone and connect it with QXDM. Your phone will be recognized as qualcomm diagnostic port 903A. Copy and paste (you can use TWRP's file manager to do this) the rmt_storage to "/system/bin" and change its permission (chmod) to 0755. This will make your changes stick upon reboot.
By the way, to use all these files, you need to be on stock CM 12.1. I haven't tried it on any other ROM.
Bro...im on cm12.1 ...rooted...I didn't understand the procedure... Pls can u explain step by step ..pls....wats that qxad ..? Is a software...? Wer I get that..,pls reply bro
Sent from my AO5510 using XDA Free mobile app
tirta.agung said:
Hi there, attached is boot.img and a hack rmt_storage for CM 12.1. Just flash the boot.img to your phone and connect it with QXDM. Your phone will be recognized as qualcomm diagnostic port 903A. Copy and paste (you can use TWRP's file manager to do this) the rmt_storage to "/system/bin" and change its permission (chmod) to 0755. This will make your changes stick upon reboot.
By the way, to use all these files, you need to be on stock CM 12.1. I haven't tried it on any other ROM.
Click to expand...
Click to collapse
Now i upgraded to cm13.....can these two files work for me....pls reply
Sent from my AO5510 using XDA Forums
@ekhasti
I have tried doing this on Yureka - CM11 XNPH05Q. Installed all the drivers & softwares successfully. When I startup the QPST config to add a new port,
1. I have to uncheck the "Show serial and USB/QC diag ports only" to make the HTCUSBModem port visible.
2. Although I am able to add the port successfully I am unable to see the phone number, it says "No Phone".
Since it is unable to get the phone details I am unable to proceed further. Nothing is visible/editable QXDM. either.
I have manually edited the build.prop file to make sure USB debugging is enabled but to no avail. Please check the attached files, what is it that I am missing?
P.S - I am able to get my IMEI number using *#06#
Any suggestion Guys???
bluebl0od said:
Any suggestion Guys???
Click to expand...
Click to collapse
Guys, I am eagerly waiting for your updates