Related
To perform a HTC HD2 Leo hard reset
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it. You will then see a message on the screen telling you this will erase xxxxxxxx......
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Soft Reset
If i may add,
A soft reset,
1. Open the back with your thumb or finger
2. The RESET button is located below the bottom left slot for the battery and the SIM card. Use a small object with a blunt point like a toothpick to the RESET button.
3. Your phone will restart and the Home screen appears.
Correct me if im wrong,
Sorry im a newb, but what is the precise difference between hard and soft reset?
Will a soft reset delete stuff such as contacts, pictures and music? And will hard reset do the same?
thanks smaberg...
you should add the two other methods to the first post
there is the soft-reset button (little red button) and a software method (clear storage).
HD2Owner said:
thanks smaberg...
you should add the two other methods to the first post
there is the soft-reset button (little red button) and a software method (clear storage).
Click to expand...
Click to collapse
the "software" method (clear storage) is a hardreset, witch means you will restore it to factory default, deleting all info on phone...
the softreset only restarts the phone.
after flashing a new ROM i always recomend a hardreset afterwards, to be sure to get rid of all leftovers...
(Useful if flashing a rom and battery is less than 50%)
Enter bootloader mode:
Momentary press the red reset button on the back of the device, near the sd card slot, while holding the volume down button. Keep pressing on the Volume down till you see the bootloader screen. If you did not have volume down pressed as you were pressing on the reset button the device is just gonna reset and no change will take place.
Else, you will see "serial" written on the bottom middle of the screen if you're not connected to the PC via USB cable yet. "USB" will replace "Serial" when windows recognizes the device. Once on this state, you can press "next" on the rom installer where you have to acknowledge you connected the device via USB and your battery is grater than 50% and so on and so on.
You can start the installer on the PC prior to connecting the device in Bootloader mode. I don´t know what happens if you enter bootloader while connected to the PC (if you don't either, don't do it!!)
Note: I advise against using this mode with less than 10% or so. I guess you could end up with largest screened brick in the market.
To clarify previous posts:
Hard reset: Resets the device to factory defaults or to the last rom you installed.
How?
-Hardware method: combo of hardware buttons (described above)
-Software method: slide through HTC sence till "Settings" bar and select "Security" (top option). Then select "Factory resets" (last option). To my knowledge it does absolutely the same thing as the hardware method. correct me if I'm wrong.
Soft Reset: changes you made will take effect after the device resets (installed apps or reg edits...) OR you got to a sticky situation and you need to reset to get everything running smooth again (device shows abnormal operation of some kind).
How?
-Software method: Hold the power button till the quick list appears and press "power off" option on the top. You can also be presented with this option after installing some apps or after changing something within an app.
-Hardware method: remove the back cover and press the little red button near the sd card slot. Useful if the device stops responding and you are unable to soft reset by any other way.
Enter Bootloader Mode: allows for flashing devices in any battery state. It doesn't do anything by itself, just allows roms to be flashed. Some people have gotten stuck on this screen http://forum.xda-developers.com/showthread.php?t=599259, so use the search tool and read up before using. After flashing a rom you will loose every setting and file you had on the device itself. SD card will remain untouched (or so it should). I've read people advising to remove the card prior to flashing. Not exactly sure as to why. Files saved to the SD will remain intact. Apps installed on the SD card (aka. "Storage") will remain intact, only not registered or linked with shortcuts anymore. The device basically doesn´t know they exist.
How?
-Harware method: button combo (described above).
-Software method(ish): If you don't have to manually enter bootloader, the rom installer will take your device through this step without you having to do anything besides connecting through USB (activesynk, I guess) and running the RUU_LEO_xxx.exe file. You will see a progress bar on both PC and device as the rom is flashed.
Note: Reseting the device (turned on) while pressing a key (ex.: vol down) does the same thing as pressing the power button (with the device turned off) while pressing that same button (vol down).
Maybe you could transfer this info to the 1st post and clean up the thread a bit... Even, this could be at the Wiki section. Or better, a link on the Wiki to this thread
Hi guys,
I tried with both volume up and down pressed to hard reset, but not really successful. Perhaps I am doing something wrong?
Regards,
Seba
sebacu said:
Hi guys,
I tried with both volume up and down pressed to hard reset, but not really successful. Perhaps I am doing something wrong?
Regards,
Seba
Click to expand...
Click to collapse
did u press power while pressing vol up/down?
Well, for entering bootloader mode, you can do it in "software mode" without having a PC connected to your PPC.
You can just run EnterBootloader.exe from your device.
(see attachment)
wazaaappp said:
did u press power while pressing vol up/down?
Click to expand...
Click to collapse
yes, I did. But when pressing I do not feel that is actually "making contact" I tried several times...
I will try with the bootloader from above...let's see...
Thanks and regards,
Seba
If, for some reason, you cant hard reset using the power button, you can always press the reset button on the back of the device while pressing both vol up and down. After the vibration, it will enter the hard reset menu (remember to keep pressing both vol buttons till this point).
By the way: were you pressing the power button and both vol buttons with the device turned off? Cuz, with it turned on, you are just cycle through the quick list and vol menu like crazy.
Yep...pressing with phone off.
I tried with the reset button from the back of the phone and it worked.
Thanks guys...
Regards,
Seba
hi..
the thing is that i cant start my phone.
i hit the power button and it shows sasmung logo button etc.. and just black screen(phone is off now,dunno)
i went into recovery mod (hit the 3 buttons) and it shows that hes downloading something(android guy with shovel)..
plz help i cant turn my phone on!
PLZ HELP!
Hold down volume up + home key + power button then wait the "samsung galaxy s" then release the 3 buttons.
Sent from my GT-I9000 using XDA App
when i do that it says downloading dont remove the target!.
help plz
http://forum.xda-developers.com/wiki/index.php?title=Samsung_Galaxy_S_Series#Recovery_Mode
Factory reset
On the Galaxy S the soft-reset is achieved by pressing and holding the power button. A hard-reset can executed by pressing and holding VolumeUP+Home+Power. There you will find the options "reboot", "apply sdcard:update.zip", "wipe data/factory reset" and "wipe cache partition".
The "wipe data/factory reset" option will restore your phone to the original configuration of the firmware YOU LAST INSTALLED (including any updates made via update.zip). This will NOT bring your phone back to the firmware installed when you originally bought it unless you haven't flashed your phone.
You can navigate the recovery screen using VolumeUp & VolumeDown and use the Home button to select.
jje
i did the factory reset and when i power on the phone it shows the "S" and just after that its black screen.
help plz
Also got a problem with my phone after updating to froyo 2.2 and then trying to apply a lag fix. Phone starts and I get the flashing S logo then the screen goes blank. Phone occasionally vibrates. Trying the Button Press listed above I'm not getting any options on my screen.
Please invest some effort in trying to solve this yourself. Read posts like these http://forum.xda-developers.com/showthread.php?t=870233, there are many many posts which describe to flash stock roms with Odin
Mine is now 100% bricked with the Screenshot. Did get adb to see the phone and got recovery mode up, didn't know what to do next really with Odin not sure how that software operates or how to re-install files. So unplugged the phone and now after some research thought I'd have another go but oh no its got the logo on it now.
Look 2 posts up ("help me unbrick my Galaxy") and read about Odin. As long as you can get into recovery or download, your Galaxy is not bricked (more a matter of its owner being clueless)
Sent from my GT-I9000 using XDA App
Can't get into download or recovery mode, phone only has that image of the phone computer and exclamation mark now. Odin can't see phone if I connect it to PC. ADB can't locate the device either. Mine is totally bricked.
Wish I hadn't bothered with the upgrade to Froyo 2.2, my phone was operating okay on 2.1. Guess I'll have to call T Mobile in the morning to arrange for a repair/replacement of this handset.
If you could enter download mode before (volume DOWN + home + power), i don't see why you can't now. Pull out your sim card, external sd card and battery, wait a few minutes, then put battery in and try to open download mode. Then just flash whichever firmware you want via odin, and it'll work. I bricked mine two times today , also showed that image with an exclamation mark between a phone and computer.
I couldn't get download mode or recovery on my phone via the button press method. I got it up by having the phone on computer and using the adb command method. As Computer can no longer see the phone I can't use this method to get back to formatting and re-flashing the file.
Please spend some time to read it.
http://forum.xda-developers.com/showthread.php?t=819551
hi, I have just registered and looking for some help if at all possible,
I have a galaxy i9505 S4 and recently the Home button seems to come and go, and the power button the same, and also the screen keeps lighting up every minute for about 10 secs, if i remove the battery I can restart the phone, and also the home button works to start the phone in factory reset mode, so i feel it might be a software problem rather than hardware.
is there any way to get the phone to reinstall the firmware, as factory reset didnt help
the phone is on orange (EE) UK
thanks for any advice or help given.
jamiet77 said:
hi, I have just registered and looking for some help if at all possible,
I have a galaxy i9505 S4 and recently the Home button seems to come and go, and the power button the same, and also the screen keeps lighting up every minute for about 10 secs, if i remove the battery I can restart the phone, and also the home button works to start the phone in factory reset mode, so i feel it might be a software problem rather than hardware.
is there any way to get the phone to reinstall the firmware, as factory reset didnt help
the phone is on orange (EE) UK
thanks for any advice or help given.
Click to expand...
Click to collapse
Hi.
Can u explain the home button issue and the screen lighting up again? what was the problem?
what firmware are u using?
maanz "L" said:
Hi.
Can u explain the home button issue and the screen lighting up again? what was the problem?
what firmware are u using?
Click to expand...
Click to collapse
hi, thanks for the reply,
the home button just dont work, single click, and holding it in for the task manager dont do nothing either, but if i turn off the phone and hold the home, vol up, and power button, it boots into reset menu fine.
on and off the power button dont work, and i have to remove the battery to restart it.
the screen just lights up every minute for about 10 secs as if it has a notification, but there is nothing there, it drains the battery to empty in about 5 hours.
cheers.
Jamie.
jamiet77 said:
hi, thanks for the reply,
the home button just dont work, single click, and holding it in for the task manager dont do nothing either, but if i turn off the phone and hold the home, vol up, and power button, it boots into reset menu fine.
on and off the power button dont work, and i have to remove the battery to restart it.
the screen just lights up every minute for about 10 secs as if it has a notification, but there is nothing there, it drains the battery to empty in about 5 hours.
cheers.
Jamie.
Click to expand...
Click to collapse
do u have a custom recovery like Philz recovery?
if u do, reboot to recovery, do factory reset and wipe cache.
then (still in recovery), go to advance, wipe dalvik cache.
Reboot yr phone.
See how it goes..
maanz "L" said:
do u have a custom recovery like Philz recovery?
if u do, reboot to recovery, do factory reset and wipe cache.
then (still in recovery), go to advance, wipe dalvik cache.
Reboot yr phone.
See how it goes..
Click to expand...
Click to collapse
I dont have that, the phone is under warantee still so would putting that on void this? I dont want to send it back as they take 28 days, and i need the phone.
so is there any other way?
jamiet77 said:
I dont have that, the phone is under warantee still so would putting that on void this? I dont want to send it back as they take 28 days, and i need the phone.
so is there any other way?
Click to expand...
Click to collapse
If u want to reflash firmware,
First u have to install Samsung kies app on yr PC here:http://forum.xda-developers.com/showthread.php?t=2038555
Then install Odin3 on yr PC here:http://forum.xda-developers.com/showthread.php?t=1728605
Download yr stock 4.2.2 firmware from XDA/Sammobile. (make sure it is in .tar.MD5 format)
After finish downloading yr firmware version, open odin.
In Odin, Make sure that ONLY AutoReboot & F.Reset Time is ticked in Odin options.
Load extracted file (.tar.MD5) as PDA in Odin.
Turn off your phone, press & hold POWER+VOLUME+DOWN buttons until phone boot into Download Mode.
Connect phone to the computer and wait for the drivers to be installed. You will see blue or yellow indicator in left top corner of Odin, with phone connected to port: COM:x
Click START and wait until you see GREEN indicator [PASS], flashing is finished.
Then, it will reboot itself. U can unplug yr USB cable.
That's it.
If u want to remove the warning triangle on boot (for warranty purposes), go here:http://forum.xda-developers.com/showthread.php?t=1494114
Hope I have help u and this is only way to do if u want reinstall yr firmware.
maanz "L" said:
If u want to reflash firmware,
First u have to install Samsung kies app on yr PC here:http://forum.xda-developers.com/showthread.php?t=2038555
Then install Odin3 on yr PC here:http://forum.xda-developers.com/showthread.php?t=1728605
Download yr stock 4.2.2 firmware from XDA/Sammobile. (make sure it is in .tar.MD5 format)
After finish downloading yr firmware version, open odin.
In Odin, Make sure that ONLY AutoReboot & F.Reset Time is ticked in Odin options.
Load extracted file (.tar.MD5) as PDA in Odin.
Turn off your phone, press & hold POWER+VOLUME+DOWN buttons until phone boot into Download Mode.
Connect phone to the computer and wait for the drivers to be installed. You will see blue or yellow indicator in left top corner of Odin, with phone connected to port: COM:x
Click START and wait until you see GREEN indicator [PASS], flashing is finished.
Then, it will reboot itself. U can unplug yr USB cable.
That's it.
If u want to remove the warning triangle on boot (for warranty purposes), go here:http://forum.xda-developers.com/showthread.php?t=1494114
Hope I have help u and this is only way to do if u want reinstall yr firmware.
Click to expand...
Click to collapse
hi, I have just done upgrade and initialisation from Kies, and it redownloaded and reinstalled the latest software, took ages, and the button is still not working, so i guess it will have to go to the shop.
cheers for all your help, the button only works before the OS has started, as i can get into recovery menu.
thanks again.
mechanical or hardware problem
That seems pretty much a mechanical problem (button broken) or hardware issue (shortcut somewhere? could explain the screen problem...)
jamiet77 said:
hi, I have just done upgrade and initialisation from Kies, and it redownloaded and reinstalled the latest software, took ages, and the button is still not working, so i guess it will have to go to the shop.
cheers for all your help, the button only works before the OS has started, as i can get into recovery menu.
thanks again.
Click to expand...
Click to collapse
droggen said:
That seems pretty much a mechanical problem (button broken) or hardware issue (shortcut somewhere? could explain the screen problem...)
Click to expand...
Click to collapse
the buttoon does work, but only to get the phone into recovery mode at startup, so physically the button works, just not when the phone is powered into the android os.
Im a bit out of ideas.
jamiet77 said:
the buttoon does work, but only to get the phone into recovery mode at startup, so physically the button works, just not when the phone is powered into the android os.
Im a bit out of ideas.
Click to expand...
Click to collapse
It's a faulty button mate.
You don't need to use the home button to boot to recovery or download mode on the S4.
You can simply press volume up+power (recovery) or volume down+power (downloadmode) no need for home button at all.
This is why you think it works.
Obagleyfreer said:
It's a faulty button mate.
You don't need to use the home button to boot to recovery or download mode on the S4.
You can simply press volume up+power (recovery) or volume down+power (downloadmode) no need for home button at all.
This is why you think it works.
Click to expand...
Click to collapse
Not true, i have this same issue after opening Wanam.
The screen turns on if i press the home button but wont do anything else (exit from an app back to home screen etc)
About to re-flash rom and / or kernel
Edit:
Also
- the lockscreen wont work
- when connected to PC, the filesystem wont show up (used 3 diff usb cables, 2 diff PC's)
FelixCited said:
Not true, i have this same issue after opening Wanam.
The screen turns on if i press the home button but wont do anything else (exit from an app back to home screen etc)
About to re-flash rom and / or kernel
Edit:
Also
- the lockscreen wont work
- when connected to PC, the filesystem wont show up (used 3 diff usb cables, 2 diff PC's)
Click to expand...
Click to collapse
It's very true mate.
YOU DO NOT NEED HOME BUTTON TO BOOT TO RECOVERY, SIMPLE.
Your issue sounds different to the OPs.
If you refer back to his first post, he said his power button doesn't do ANYTHING.
"the home button just dont work, single click, and holding it in for the task manager dont do nothing either, but if i turn off the phone and hold the home, vol up, and power button, it boots into reset menu fine"
Yours works.
I recently (successfully?) rooted my phone, but couldn't make phone calls or texts so I tried factory resetting it. The factory reset worked but I still had the root and I couldnt make calls or texts, so I tried multiple times to unroot it through Odin and it said it worked on my last attempt, but now my phone is stuck on a black screen and a blue LED pops up. I get no vibrations or feedback from my phone. I've tried all the combos to reset, down home power, down power, power home up, home power, all of them. My only hope is to let the phone die of power and recharge it and see if it will work. Does anyone have any ideas? When I plug it in to my computer it wont detect it either.
check your IMEI with *#06#!
when you have no IMEI you need the EFS BackUp...hope you have it.
Regards
sonic76
power button + volume down. When it reboots, quickly get into download mode the same way you would normally. And same as above post, EFS back.. if it's not resolved from factory reset.
I have had this problem.
If you just hold power vol- down it will reboot and when reeboting, just keep holding the same buttons until you get the Download Mode.
If not try holding power vol- up until geeting into recovery, then go trough download mode from there.
You just have to hold the buttons down, it wil maybe restart but just keep holding these buttons trough the restarts.
In download mode you have to do a fresh install with a rom of your choice from Sammobile, orginal firmware.
And remember to never Factory Reset your phone after innstaling ROOT and Recovery.
The best way to do factory reset after these are firmware flash trough Odin.
sonic76 said:
check your IMEI with *#06#!
when you have no IMEI you need the EFS BackUp...hope you have it.
Regards
sonic76
Click to expand...
Click to collapse
Sadly All I get is a black screen..
LyLu said:
I have had this problem.
If you just hold power vol- down it will reboot and when reeboting, just keep holding the same buttons until you get the Download Mode.
If not try holding power vol- up until geeting into recovery, then go trough download mode from there.
You just have to hold the buttons down, it wil maybe restart but just keep holding these buttons trough the restarts.
In download mode you have to do a fresh install with a rom of your choice from Sammobile, orginal firmware.
And remember to never Factory Reset your phone after innstaling ROOT and Recovery.
The best way to do factory reset after these are firmware flash trough Odin.
Click to expand...
Click to collapse
I kinda did a factory reset after rooting.. how does that affect it? And also i've held those buttons you've said to hold for over 2 minutes and nothing happens :/
Good evening everyone, i'm having a serious issue with my samsung A5. It was rooted, with custom recovery and custorm rom (Android 6.1 i think).
2 Days ago, a chewingum got stuck on my screen. I tried to remove it with nail paint remover, it did the trick but then my home button stopped working: the button itself can be pressed normally, but it won't work. I also experienced randomly long home button press actions, so i decided to turn them off. I thought that few drops of liquid may actually have gone beneath the home button. Few hours later, i experienced more issues: volume going up without anyone pressing the button (and the buttons are not stuck at all, and that side never got close to liquids), power button not doing his job etc. I tried to do a soft reset by recovery (cleaning cache and dalvik) but i ended up aslo factory resetting it for a distraction. Reconfigured the device, everything was back to normal (except the home button) but then i also experienced a couple of random volume up and crashes upon making phonecalls. SO i decided to reflash the entire rom, downloaded it + gapps, put into the decide, rebooted in recovery. Wipe cache, dalvik and also system i think, then i tried to intall the zip files but they were not there (probably i should have avoided wiping system, i get confused sometimes). I turned the device off and on, and now i'm stuck on bootloop (regular mode), can reboot it but it seems i can't go in either recovery or donwload mode (so no odin flash). Device is not recognized by the Pc. I keep rebooting it with power + home + volume down and as soon as i see the screen turn black, i try to press again volume up + home to enter recovery, but it goes straight to bootloop.
Any idea on how getting out of this situation? Thank you in advance
Dharmost said:
Good evening everyone, i'm having a serious issue with my samsung A5. It was rooted, with custom recovery and custorm rom (Android 6.1 i think).
2 Days ago, a chewingum got stuck on my screen. I tried to remove it with nail paint remover, it did the trick but then my home button stopped working: the button itself can be pressed normally, but it won't work. I also experienced randomly long home button press actions, so i decided to turn them off. I thought that few drops of liquid may actually have gone beneath the home button. Few hours later, i experienced more issues: volume going up without anyone pressing the button (and the buttons are not stuck at all, and that side never got close to liquids), power button not doing his job etc. I tried to do a soft reset by recovery (cleaning cache and dalvik) but i ended up aslo factory resetting it for a distraction. Reconfigured the device, everything was back to normal (except the home button) but then i also experienced a couple of random volume up and crashes upon making phonecalls. SO i decided to reflash the entire rom, downloaded it + gapps, put into the decide, rebooted in recovery. Wipe cache, dalvik and also system i think, then i tried to intall the zip files but they were not there (probably i should have avoided wiping system, i get confused sometimes). I turned the device off and on, and now i'm stuck on bootloop (regular mode), can reboot it but it seems i can't go in either recovery or donwload mode (so no odin flash). Device is not recognized by the Pc. I keep rebooting it with power + home + volume down and as soon as i see the screen turn black, i try to press again volume up + home to enter recovery, but it goes straight to bootloop.
Any idea on how getting out of this situation? Thank you in advance
Click to expand...
Click to collapse
Sadly, no software can fix broken hardware, it's probably best, as you'll now know, not to pour chemical liquids onto electrical devices, and just what kind of chewing gum exists that requires such extreme cleaning measures from a flat, non-porous surface I'll never know.
That said, as for rebooting, a force-restart on your device *doesn't* require you to hold Home+Volume down+Power, that should only reboot you to bootloader/download mode.
Try again only holding Power+Volume Down. THEN, when your screen goes fully black, immediately switch to Power+Volume up+Home.
You should then boot into recovery mode without any loop.
Good luck!
D4ND310 said:
Sadly, no software can fix broken hardware, it's probably best, as you'll now know, not to pour chemical liquids onto electrical devices, and just what kind of chewing gum exists that requires such extreme cleaning measures from a flat, non-porous surface I'll never know.
That said, as for rebooting, a force-restart on your device *doesn't* require you to hold Home+Volume down+Power, that should only reboot you to bootloader/download mode.
Try again only holding Power+Volume Down. THEN, when your screen goes fully black, immediately switch to Power+Volume up+Home.
You should then boot into recovery mode without any loop.
Good luck!
Click to expand...
Click to collapse
I didn't dip the smartphone into a cup of liquid, i just took a piece of cotton, poured a bit of nail pain remover (don't know the exact name in english, sorry) on it and then scratched the part where the chewing gum was on (on the soft touch back key, which works 100% fine).
I am trying using the method you described, but it seems i can't go into recovery. Maybe i'm not quick enough! will keep trying. If you have any other suggestions i will be glad to hear that!
You could try to make a USB jig, or buy one off of eBay. They're really cheap. Its basicly just a resistens that force the phone to download mode. It have worked fine for all my Sammy's including A310 so it probably works for A (15) series as well.
Just put it in USB connector and press power for a few secs and you should be in download mode.
Just an idea if everything else fails
Sent from my Honor 5X using Tapatalk
go to samsung
A hardware problem could NEVER be fixed by software ways... Unfortunatelly...
It seems that liquid made some changes on your PCB (maybe dissolved some isolators inside??)...
Anyway, go to service or replace it!
Hello everyone, i've updates about my problem and i would be glad if you could kindly point me in the right direction.
I purchased an USB Jig as suggested by one of you guys, i forced the device into dowload mode and installed a fresh stock firmware + custom recovery. When i try to boot i get a bootloop on samsung logo, and can't go into recovery probably because of the broken home button. I would like to enter recovery by using ADB command, i used to do it in the early days of Android but i'm a bit rusty and all the guides tell the procedure from an already functioning device. Since i can start it properly, is there a way to reboot it in recovery via ADB?
Thank you in advance
Dharmost said:
Hello everyone, i've updates about my problem and i would be glad if you could kindly point me in the right direction.
I purchased an USB Jig as suggested by one of you guys, i forced the device into dowload mode and installed a fresh stock firmware + custom recovery. When i try to boot i get a bootloop on samsung logo, and can't go into recovery probably because of the broken home button. I would like to enter recovery by using ADB command, i used to do it in the early days of Android but i'm a bit rusty and all the guides tell the procedure from an already functioning device. Since i can start it properly, is there a way to reboot it in recovery via ADB?
Thank you in advance
Click to expand...
Click to collapse
if you can access Download mode try this. hold volume down+home+power button. once the screen is black simply turn your finger to volume up while still holding the power and home button then release when SAMSUNG appears.
Sent from my SM-A500F using xda premium
babyyeobo14 said:
if you can access Download mode try this. hold volume down+home+power button. once the screen is black simply turn your finger to volume up while still holding the power and home button then release when SAMSUNG appears.
Sent from my SM-A500F using xda premium
Click to expand...
Click to collapse
Thanks for the suggestion, but still couldn't get into recovery. I think the home button is really broken, therefore i need to access recovery in another way.
Cause i flashed the stock samsung firmware twice with odin and i can't still start the phone properly, every guide says that a wipe of cache and dalvik solves the situation. But i need to get into recovery for that.
I can't go into recovery with normal procedure probably because the home button is not working, and all the guides about adb commands say that you need to plug in your phone when it has fully started. So i either need a way to force the device into recovery with my computer, or a firmware that once flashed doesn't give me bootloop