Database Users

Freezed in download mode

I can't do anything, it's freezed and whenever i go out of it, i get the sign of connecting to computer.
Also when i try to install any ROM, it just freezes in download mode, what can i do?

pull battery out for 10 sec already done?

corgar said:
pull battery out for 10 sec already done?
Click to expand...
Click to collapse
Done already, thanks for answering so quickly
It freezes after doing this:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!

Try searching the q & a section of the forum. That should have been your first port of call.
Dan

try to check if any instance of kies is running in bg

Download Odin3 1.7 and try to flash a stock JM8 firmware with 512 pit re-partitioned. Don't worry, the Phone ! PC isn't a total brick. This happened to me and this should work for you.

corgar said:
try to check if any instance of kies is running in bg
Click to expand...
Click to collapse
There is one... now i've closed it, what now?

Bess833 said:
Download Odin3 1.7 and try to flash a stock JM8 firmware with 512 pit re-partitioned. Don't worry, the Phone ! PC isn't a total brick. This happened to me and this should work for you.
Click to expand...
Click to collapse
Ok, i'm gonna try to.

Run odin as an administrator and also wrong section.

jaju123 said:
Run odin as an administrator and also wrong section.
Click to expand...
Click to collapse
Sorry man, it's just im so nervous i don't know what to do, sorry

coldflid said:
There is one... now i've closed it, what now?
Click to expand...
Click to collapse
try using odin 1.3 and not 1.7
first of all, take out the simcard and the ext sd-card.
turn off the kies (dont let it run in the tray)
start odin and put all the needed files in
start the phone in download mode and connect it to the computer.
start the rom burning.

coldflid said:
Sorry man, it's just im so nervous i don't know what to do, sorry
Click to expand...
Click to collapse
Don't worry, keep your calm. Your phone is not a total brick, it's almost impossible. With Odin3 v1.7 and JM8 + 512 pit, you should be up and running in no time.
As long as you are able to get to Download mode, you can keep calm. Don't worry
genich1971 said:
try using odin 1.3 and not 1.7
Click to expand...
Click to collapse
Odin 1.7 > Odin 1.3 when it comes to unbricking in my experience.

close kies process and try to reflash again

Bess833 said:
Don't worry, keep your calm. Your phone is not a total brick, it's almost impossible. With Odin3 v1.7 and JM8 + 512 pit, you should be up and running in no time.
As long as you are able to get to Download mode, you can keep calm. Don't worry
Odin 1.7 > Odin 1.3 when it comes to unbricking in my experience.
Click to expand...
Click to collapse
I've tried with 1.3 only, gonna try 1.7
Btw, someone has the link to the JM8, i can't download it from samfirmwares, doesn't let me.

coldflid said:
I've tried with 1.3 only, gonna try 1.7
Btw, someone has the link to the JM8, i can't download it from samfirmwares, doesn't let me.
Click to expand...
Click to collapse
[ROM] Release: I9000XWJM9 - MultiCSC(s) Europe
JM9 should do the trick too.

Thanks everyone, seems its working alright now.
You're great man, i didn't think i would manage to do it.
Btw, Odin 3 1.7 unbricks better than 1.3 for what i've seen

coldflid said:
Thanks everyone, seems its working alright now.
You're great man, i didn't think i would manage to do it.
Btw, Odin 3 1.7 unbricks better than 1.3 for what i've seen
Click to expand...
Click to collapse
Indeed and gratz. Now you can go ahead and flash any ROM/Firmware you want again.

coldflid said:
Thanks everyone, seems its working alright now.
You're great man, i didn't think i would manage to do it.
Btw, Odin 3 1.7 unbricks better than 1.3 for what i've seen
Click to expand...
Click to collapse
Actually, when i booted first time i get an error in recvovery saying:
multicsc
can not acces to /system/csc/XEE/system/.
Guess it's an error of CSC, can someone give me the link to a working one ?

coldflid said:
Actually, when i booted first time i get an error in recvovery saying:
multicsc
can not acces to /system/csc/XEE/system/.
Guess it's an error of CSC, can someone give me the link to a working one ?
Click to expand...
Click to collapse
Where are you from and what CSC you used?

coldflid said:
Actually, when i booted first time i get an error in recvovery saying:
multicsc
can not acces to /system/csc/XEE/system/.
Guess it's an error of CSC, can someone give me the link to a working one ?
Click to expand...
Click to collapse
I correct myself again. Indeed, it was an error in the CSC, i just tried using Odin v3 1.7 and the JPU rom and for now it seems it's working it's way through. I'll edit when it finishes to tell you the result.
Thanks again
Now it's working just fine.
Thanks a lot

Bricked my Bell Galaxy S. help needed badly PLEASE PLEASE PLEASE!!

Hi guys,
I had darky's rom on my phone and then i had to factory reset it. It was working fine after the factory reset. I wanted to go back to stock firmware since i was planning on taking my phone to the Bell store tomorrow but in doing so i bricked my phone. Now all it does is show the boot screen and then the screen turns black and it keeps on vibrating randomly.
Can anyone PLEASE help me with this? I wanna go back to stock firmware if possible, or any firmware really i just wanna get my phone working. please help

superstrongboy said:
Hi guys,
I had darky's rom on my phone and then i had to factory reset it. It was working fine after the factory reset. I wanted to go back to stock firmware since i was planning on taking my phone to the Bell store tomorrow but in doing so i bricked my phone. Now all it does is show the boot screen and then the screen turns black and it keeps on vibrating randomly.
Can anyone PLEASE help me with this? I wanna go back to stock firmware if possible, or any firmware really i just wanna get my phone working. please help
Click to expand...
Click to collapse
What version of darky's rom were you using and which stock firmware version did you want to go back to?
It could be that you were using a version of darky's rom that is gingerbread and you flashed back to the froyo stock rom.

superstrongboy said:
Hi guys,
I had darky's rom on my phone and then i had to factory reset it. It was working fine after the factory reset. I wanted to go back to stock firmware since i was planning on taking my phone to the Bell store tomorrow but in doing so i bricked my phone. Now all it does is show the boot screen and then the screen turns black and it keeps on vibrating randomly.
Can anyone PLEASE help me with this? I wanna go back to stock firmware if possible, or any firmware really i just wanna get my phone working. please help
Click to expand...
Click to collapse
Ok, try to turn on the phone pressing VOLUME DOWN+HOME+POWER and see if the phone goes in Download Mode.
Then, follow the guides that you can find in the forum and flash with ODIN a new ROM (I suggest JS8 if you're in EUROPE, Froyo 2.2.1)

Download Mode work ? 3 buttons holding Vol down+home+power

bobloblawsum said:
What version of darky's rom were you using and which stock firmware version did you want to go back to?
It could be that you were using a version of darky's rom that is gingerbread and you flashed back to the froyo stock rom.
Click to expand...
Click to collapse
I had darky's ressurection edition rom and i had it on froyo.
i want to go back to any firmware version that will get my phone working

olivercervera said:
Ok, try to turn on the phone pressing VOLUME DOWN+HOME+POWER and see if the phone goes in Download Mode.
Then, follow the guides that you can find in the forum and flash with ODIN a new ROM (I suggest JS8 if you're in EUROPE, Froyo 2.2.1)
Click to expand...
Click to collapse
yeah it goes into download mode
. I live in canada.
can you please link me to the proper firmware for Canada's bell SGS? and possibly if there's a guide on how to go back because i m a total noob.

superstrongboy said:
yeah it goes into download mode
. I live in canada.
can you please link me to the proper firmware for Canada's bell SGS? and possibly if there's a guide on how to go back because i m a total noob.
Click to expand...
Click to collapse
Here is a link to the official stock Bell JL2 firmware, there is a slightly newer one but i can't find the link and this should work fine.
You will need to use Odin to flash the file
*edit; forgot the link. http://www.multiupload.com/UTFJCCIP5H

download a stock Eclair or Froyo Rom from samfirmware.com with (512.pit,PDA,MODEM,CSC) get in download mode (vol up+power+menu all at the same time) flash via ODIN DO NOT UNPLUG wait till full flash make shure you have at least 60% battery left before flashing
if it dosen't work search around you'll find some methods its not bricked its just in a continuous loop

i tried flashing with that link you gave, but ODIN doesnt do anything after this
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..

superstrongboy said:
i tried flashing with that link you gave, but ODIN doesnt do anything after this
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
Click to expand...
Click to collapse
Did you add the tar file to the PDA section of Odin? That should be all that's needed in odin, no repartition, no pit file and the Tar file that was extracted from the Zip file placed in the PDA section of odin.
I forgot to add, did you run Odin as an administrator?

bobloblawsum said:
Did you add the tar file to the PDA section of Odin? That should be all that's needed in odin, no repartition, no pit file and the Tar file that was extracted from the Zip file placed in the PDA section of odin.
Click to expand...
Click to collapse
yeah i did that it wasnt moving forward.
then i disconnected and now when i press HOME+VOL. UP+POWER or only power button, i get the [Phone -- ! -- PC] symbol. i can still go into download mode idk what to do im so screwed.
yeah i m running odin as admin

i flashed that firmware onto my phone.
now all it does is freeze at the Galaxy S screen and vibrates randomly. what do?

superstrongboy said:
i flashed that firmware onto my phone.
now all it does is freeze at the Galaxy S screen and vibrates randomly. what do?
Click to expand...
Click to collapse
Here is the thread where i got the link to the Rom from, i'm reading through it now to see if there are any similar problems http://forum.xda-developers.com/showthread.php?t=883568

According to post #45 on that thread you should flash the rom with the 'Phone Bootloader Update' option checked.
I'm not 100% certain on that and don't want to give you some wrong advice but if i remember right, it was the new bootloader in JL2 that fixed the SD card problems that the Bell vibrants had. It's up to you if you want to try flashing the file with that option checked. Unless you get some better advice.

superstrongboy said:
i flashed that firmware onto my phone.
now all it does is freeze at the Galaxy S screen and vibrates randomly. what do?
Click to expand...
Click to collapse
had u ever upgrade to 2.3.3 ?
try those roms
UGJL2/BMCJL2/UGJL2 (North America for I9000M only)
UGKC1/BMCKC1/UGKC1 (North America for I9000M only)
i dont have any link atm , i will search about that and i will edit my post

NCSoft said:
had u ever upgrade to 2.3.3 ?
try those roms
UGJL2/BMCJL2/UGJL2 (North America for I9000M only)
UGKC1/BMCKC1/UGKC1 (North America for I9000M only)
i dont have any link atm , i will search about that and i will edit my post
Click to expand...
Click to collapse
nope i havent ever upgraded to 2.3.3
and if i take my bricked phone to the store, will they replace it? I still am under the warranty period

superstrongboy said:
nope i havent ever upgraded to 2.3.3
and if i take my bricked phone to the store, will they replace it? I still am under the warranty period
Click to expand...
Click to collapse
They'll send it off to the repair centre and try to determine and fix the problem. If they think the problem was caused by you then they might try to charge you a fee for fixing it.
Have you installed Kies on your laptop before (just to know if you have the samsung drivers that come with it installed)
If it has come to the point where you're thinking of bringing it to the store then, personally, i would try flashing the JL2 rom with the update bootloader option checked. That's just what i'd do personally though.
It could also be something simple like trying to flash it from a different usb port.

bobloblawsum said:
According to post #45 on that thread you should flash the rom with the 'Phone Bootloader Update' option checked.
I'm not 100% certain on that and don't want to give you some wrong advice but if i remember right, it was the new bootloader in JL2 that fixed the SD card problems that the Bell vibrants had. It's up to you if you want to try flashing the file with that option checked. Unless you get some better advice.
Click to expand...
Click to collapse
THANK YOU SO MUCHHHH!!!!! I DID IT AND ITS WORKING NOW!!! YAYAAAAYAAAAAAAAY CANT TElL YOU HOW HAPPY I AM LOL you're a life saver mate.

superstrongboy said:
THANK YOU SO MUCHHHH!!!!! I DID IT AND ITS WORKING NOW!!! YAYAAAAYAAAAAAAAY CANT TElL YOU HOW HAPPY I AM LOL you're a life saver mate.
Click to expand...
Click to collapse
Yea, that was the problem; now I remember! Some months ago, I had your same problem (an apparent brick, vibrating on the big S at the startup). A user suggested me to simply flash a FW with a Bootloader (at the time, the JPU), ad it worked ^^

superstrongboy said:
THANK YOU SO MUCHHHH!!!!! I DID IT AND ITS WORKING NOW!!! YAYAAAAYAAAAAAAAY CANT TElL YOU HOW HAPPY I AM LOL you're a life saver mate.
Click to expand...
Click to collapse
Haha, no problem! glad to help
i was in the same position a few months ago and the JL2 rom helped me out. I keep a copy of it on my harddrive to use if things go tits up again.

[Q] [Soft Brick] At&t Samsung Galaxy 4S (MF3/4.2.2/SGH-I337) [[[HELP PLEASE]]]

Hi guys, I'm new to this site. I have a specific problem that I can't seem to find the answer for.
My phone: At&t Samsung Galaxy S4 (I made a typo in the title... )
Model: SGH-I337
I had MF3 version/4.2.2
I used various threads to eventually root my phone.
I was very happy.
I had to use safestrap
I was happy with safestrap
I had my stock in the stock rom slot
I had [ROM] Google Edition 4.3 [Clean][Deodex][276MB][2013.11.21] in first slot.
I was very happy with it.
Here is the thread http://forum.xda-developers.com/showthread.php?p=47718525#post47718525
I made a stupid move when I was finally done, I had my phone rooted, I had everything I needed, but it wasn't enough...
I did something in the mount options area in safestrap.. switched my sd to internal memory
My phone has been in a boot loop ever since on Samsung Image
I had Slot 1 active when this happened.
When I'm in recovery mode, all the options, including wipe data/factory reset doesn't work
I tried using a pit file in Odin to fix/failed
I tried using Odin 3.09 with stock firmware I found in some threads to try and get factory/failed
I get this in Odin along with fail "All threads completed. (succeed 0 / failed 1)"
I really want to fix my phone.
Preferably I would like it to stay as mf3
Does anyone have a solution?
A link to a thread I missed?
Something more recent?
I also tried Kies, but it was giving me trouble, I'll try it again as a last resort.
I hope there's a solution. ​

Kies 3
Kies 3 didn't work as well with emergency upgrade.

worried
joeydija said:
Kies 3 didn't work as well with emergency upgrade.
Click to expand...
Click to collapse
SW Rev Check Fail fused 2 Binary 1

Whoa.
Here is the solution!
Place all files found in the zip he gives in Odin 3.09
Top - BL
Bottom - CSC
http://forum.xda-developers.com/showthread.php?t=2716482
Makes sense, makes sense?
WOWza, very happy.
:good:

I spoke too soon.
joeydija said:
Here is the solution!
Place all files found in the zip he gives in Odin 3.09
Top - BL
Bottom - CSC
http://forum.xda-developers.com/showthread.php?t=2716482
Makes sense, makes sense?
WOWza, very happy.
:good:
Click to expand...
Click to collapse
Failed at the end.. I guess that's not the right order.. farthest I've got so far though, now when I boot I see Odin.
[Not the God]

hoorah!
The solution. FINALLY.
The file order goes like this...
AP gets the biggest file size
The one that starts with Base Loader goes in BL
The one that starts with CSC goes in CSC
The last one goes in CP
[solved] happy

joeydija said:
The solution. FINALLY.
The file order goes like this...
AP gets the biggest file size
The one that starts with Base Loader goes in BL
The one that starts with CSC goes in CSC
The last one goes in CP
[solved] happy
Click to expand...
Click to collapse
Hey man, can I get a mirror to the files you used? I have the SAME EXACT ISSUE! Please and thanks!

of course
SnowDot said:
Hey man, can I get a mirror to the files you used? I have the SAME EXACT ISSUE! Please and thanks!
Click to expand...
Click to collapse
Download link: https://mega.co.nz/#!MwAhlDyC!UOnkMFsUSctakHRfE1Mr95c1ymVwy1wBPu2yiPerros
If you've never used this site before
It's kind of weird
Press the DOWNLOAD button, it's RED
Wait for 100%
When you reach 100% it either starts downloading by itself or you press the download symbol
Good luck!

Summon odin
SnowDot said:
Hey man, can I get a mirror to the files you used? I have the SAME EXACT ISSUE! Please and thanks!
Click to expand...
Click to collapse
Also, you can find Odin3 v3.09 here: https://www.androidfilehost.com/?fid=23321874045862094
Remember to run Odin3 v3.09 as administrator
Right click Odin3 v3.09, press Run as administrator
Make sure you have your USB connected to back of computer
Take out battery from device
Place battery back in
Hold Volume Down + Home Button + Power Button
When you see WARNING! press Volume Up
Plug in USB
Wait for Odin3 v3.09 to recognize your phone
Leave all default settings
Place files from mf3. Tar in slots
Press START and wait 5 minutes
Good luck!

Another Soft Bricked SGH-I337...
joeydija said:
Also, you can find Odin3 v3.09 here: https://www.androidfilehost.com/?fid=23321874045862094
Remember to run Odin3 v3.09 as administrator
Right click Odin3 v3.09, press Run as administrator
Make sure you have your USB connected to back of computer
Take out battery from device
Place battery back in
Hold Volume Down + Home Button + Power Button
When you see WARNING! press Volume Up
Plug in USB
Wait for Odin3 v3.09 to recognize your phone
Leave all default settings
Place files from mf3. Tar in slots
Press START and wait 5 minutes
Good luck!
Click to expand...
Click to collapse
Joey, thanks for the resources as there are so many broken links out there.
I'm having the same issue; however, I'm finding very little success flashing with Odin to return back to stock.
Following the same steps you've outlined above, I receive a the following from Odin:
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
and the following from the prompt on the S4 screen:
SW REV. CHECK FAIL : fused : 4, Binary : 2
Click to expand...
Click to collapse
I've tried multiple prescribed methods, including the one you outlined, using Kies, and using nkhater's method for Unbricking I337 posted here.
I'm not entirely sure what steps to take next but any thoughts would be greatly appreciated.

mythandier said:
Joey, thanks for the resources as there are so many broken links out there.
I'm having the same issue; however, I'm finding very little success flashing with Odin to return back to stock.
Following the same steps you've outlined above, I receive a the following from Odin:
and the following from the prompt on the S4 screen:
I've tried multiple prescribed methods, including the one you outlined, using Kies, and using nkhater's method for Unbricking I337 posted here.
I'm not entirely sure what steps to take next but any thoughts would be greatly appreciated.
Click to expand...
Click to collapse
The SW REV. CHECK FAIL : fused : 4, Binary : 2 error means you are trying to flash an earlier version than your phone had before. You'll need to flash the same version you were using before, either MK2 or NB1. You can find the ODIN TAR files for them in the General section.

777
DeadlySin9 said:
The SW REV. CHECK FAIL : fused : 4, Binary : 2 error means you are trying to flash an earlier version than your phone had before. You'll need to flash the same version you were using before, either MK2 or NB1. You can find the ODIN TAR files for them in the General section.
Click to expand...
Click to collapse
Thanks for helping that guy out,
I have a question...
What ROM would you recommend for a 4.2.2 MF3 At&t Galaxy S4 SGH-I337?
I've been using the ROM found in here.
I am new to the rooted world.
It's the first ROM I tried and I love it.
I can go a whole day with, at most, losing 25% battery life.
I love the minimalist aspects of it.
I don't know how to keep track of new ROMs for my build though.
I don't really want to change ROMs at the moment, because I have everything I need with this one,
but if you can give me some cool advice, that would be awesome.
Any help, information, would be appreciated.
-Joey

software update failed sm910v

I tried downgrading after looking everywhere for a possible problem with odin.. I was on the latest cpg2 and odined the bp1 firmware for 5.1 and it stuck on rpm or something like that forgive me but i cant recall..I pulled it after 20 min and then got a software update error..and no matter what firmware i tried to put on its stuck on get pit for mapping.. My computer sees it as a device MSM8960.. So kies ng. Odin works but cant pass pit Please anyone i know with latest update I should not of done this..I even tried latest firmware it was on but same error

davekaz said:
I tried downgrading after looking everywhere for a possible problem with odin.. I was on the latest cpg2 and odined the bp1 firmware for 5.1 and it stuck on rpm or something like that forgive me but i cant recall..I pulled it after 20 min and then got a software update error..and no matter what firmware i tried to put on its stuck on get pit for mapping.. My computer sees it as a device MSM8960.. So kies ng. Odin works but cant pass pit Please anyone i know with latest update I should not of done this..I even tried latest firmware it was on but same error
Click to expand...
Click to collapse
Restart pc and try latest firmware again

Trex888 said:
Restart pc and try latest firmware again[/QU
THANKS FOR REPLY ive tried every imaginable firmware for it including newest it was on and still get pit error
Click to expand...
Click to collapse

davekaz said:
Trex888 said:
Restart pc and try latest firmware again[/QU
THANKS FOR REPLY ive tried every imaginable firmware for it including newest it was on and still get pit error
Click to expand...
Click to collapse
Downliad repair firmware from link below
This will comes with pit file
Flash repair firmware with pit file and hopefully this will solve the issue.
Make sure download correct firmware for your model.
http://www.tsar3000.com/Joomla/inde...ader-csc-pit-files&catid=55:samsung&Itemid=82
Click to expand...
Click to collapse

Trex888 said:
davekaz said:
Downliad repair firmware from link below
This will comes with pit file
Flash repair firmware with pit file and hopefully this will solve the issue.
Make sure download correct firmware for your model.
http://www.tsar3000.com/Joomla/inde...ader-csc-pit-files&catid=55:samsung&Itemid=82[/QUOTE
Thanks again
placing a specific pit fit got me pass map and now gets stuck at hlo bin.. I think the downgrade firmware changed something cause windows sees phone as device called msm8960 . Odin sees it as far as a com port but beyond that its not a 910v anymore
Click to expand...
Click to collapse
Click to expand...
Click to collapse

davekaz said:
Trex888 said:
davekaz said:
Downliad repair firmware from link below
This will comes with pit file
Flash repair firmware with pit file and hopefully this will solve the issue.
Make sure download correct firmware for your model.
http://www.tsar3000.com/Joomla/inde...ader-csc-pit-files&catid=55:samsung&Itemid=82[/QUOTE
Thanks again
placing a specific pit fit got me pass map and now gets stuck at hlo bin.. I think the downgrade firmware changed something cause windows sees phone as device called msm8960 . Odin sees it as far as a com port but beyond that its not a 910v anymore
Click to expand...
Click to collapse
Try different odin version and different usb cable
Click to expand...
Click to collapse
Click to expand...
Click to collapse

Trex888 said:
davekaz said:
Trex888 said:
Try different odin version and different usb cable
Click to expand...
Click to collapse
I tried several versions of odin and its definitely not cord
Thanks again
Click to expand...
Click to collapse
Click to expand...
Click to collapse

davekaz said:
Trex888 said:
davekaz said:
I tried several versions of odin and its definitely not cord
Thanks again
Click to expand...
Click to collapse
Try this method if your bootloader is unlocked or you got developer edition n910v.
Flash twrp in odin
Make complete wipe 3× 3 times
(dalvik cache/data/cache/system/internal storage)
After wipe go to download mode
Close odin and open again as (run as administrator)& upload firmware (AP)
Hit start Flash firmware
After flash firmware DONT LET THE PHONE BOOT
go to recovery
Wile cache & data factory reset
Reboot & wait 5 to 10 minutes.
Report back
Click to expand...
Click to collapse
Click to expand...
Click to collapse

Trex888 said:
davekaz said:
Trex888 said:
Try this method if your bootloader is unlocked or you got developer edition n910v.
Flash twrp in odin
Make complete wipe 3× 3 times
(dalvik cache/data/cache/system/internal storage)
After wipe go to download mode
Close odin and open again as (run as administrator)& upload firmware (AP)
Hit start Flash firmware
After flash firmware DONT LET THE PHONE BOOT
go to recovery
Wile cache & data factory reset
Reboot & wait 5 to 10 minutes.
Report back
Click to expand...
Click to collapse
thanks for trying but I just bought the phone and was trying to downgrade to unlock..so dont think twrp will take..
I appreciate all you help but im screwed
Click to expand...
Click to collapse
Click to expand...
Click to collapse

davekaz said:
Trex888 said:
Restart pc and try latest firmware again[/QU
THANKS FOR REPLY ive tried every imaginable firmware for it including newest it was on and still get pit error
Click to expand...
Click to collapse
Did you solve your issue?
Click to expand...
Click to collapse

I did it..! SOLVED..!
alca00 said:
davekaz said:
Did you solve your issue?
Click to expand...
Click to collapse
Trex888 said:
davekaz said:
Downliad repair firmware from link below
This will comes with pit file
Flash repair firmware with pit file and hopefully this will solve the issue.
Make sure download correct firmware for your model.
http://www.tsar3000.com/Joomla/inde...ader-csc-pit-files&catid=55:samsung&Itemid=82
Click to expand...
Click to collapse
I did it..! Using this repair firmware, I have repaired my Samsung N910V. Many thanks to Trex888..! I just flashed it by Odin using this file, and I hope this can help others with same issue (soft bricked Note4 N910V).
Thanks a lot again Trex888..!
Click to expand...
Click to collapse
Click to expand...
Click to collapse

alca00 said:
alca00 said:
Trex888 said:
I did it..! Using this repair firmware, I have repaired my Samsung N910V. Many thanks to Trex888..! I just flashed it by Odin using this file, and I hope this can help others with same issue (soft bricked Note4 N910V).
Thanks a lot again Trex888..!
Click to expand...
Click to collapse
Congrats ! Glad to hear that .
Click to expand...
Click to collapse
Click to expand...
Click to collapse

alca00 said:
davekaz said:
Did you solve your issue?
Click to expand...
Click to collapse
yes it was the damned usb cord..Lol everything went smooth after that
Thanks to all
Click to expand...
Click to collapse

I had same issue, fail on all firmware (Verizon Note 4), changed usb cord, flashed back to stock and was even able to downgrade (5.0.1).

Pls help me out guys.....my two weeks old samsung note 4 is stock on Software Update Failed
Your device didnt update successfully. Use the Verizon Software Repair Assistant on a computer to repair your device and complete the update.
My phone details:
Model: SM-N910V
SKU: SMN910VZKE
Thanks.

Does anyone have this file? The page is dead.

Dear all,
i got a samsung Note 4 . Device had a sticker SM-910 F with matching imei on software. One day I hard rest my device then it imei shows Null and it became restart after 1 to 2 minutes in lop. this device has Verizon mother board. and also do not show the usb cable option. I want to install Verison stock firmware but no device detected in odin. Kindly anyone help me to install firmware through SD

Sumupali said:
Dear all,
i got a samsung Note 4 . Device had a sticker SM-910 F with matching imei on software. One day I hard rest my device then it imei shows Null and it became restart after 1 to 2 minutes in lop. this device has Verizon mother board. and also do not show the usb cable option. I want to install Verison stock firmware but no device detected in odin. Kindly anyone help me to install firmware through SD
Click to expand...
Click to collapse
A 910F with a Verizon mobo?
Might be tricky to flash.
You can access download mode?
Tried different cables / USB ports?
I really doubt that you can flash stock ROM from SD when phone is boot looping.
Maybe with terminal but you would have to flash TWRP for that first.

Downgrading Sprint S8+

Got the G955USQS5DSE5 update on my sprint S8+ last night and it basically killed my network connection. I have tried a bunch of things and nothing is working. Do I need anything special to downgrade to the previous firmware? Also, is there a best place to get the file? My phone isn't rooted or anything. It's all stock.

DAREALGUMMY said:
Got the G955USQS5DSE5 update on my sprint S8+ last night and it basically killed my network connection. I have tried a bunch of things and nothing is working. Do I need anything special to downgrade to the previous firmware? Also, is there a best place to get the file? My phone isn't rooted or anything. It's all stock.
Click to expand...
Click to collapse
From what you quoted ( G955USQSS5FSE5 ) you can only down grade to versions that had a version 5 bootloader ( 5th number from right of firmware name ). In your case version 5.
Firmware can be downloaded from sammobile or updato ( websites ). There are other sites as well.
You will need latest Samsung drivers ( for PC ) and Odin version 3.13.3 to flash firmware.
As for network issues don't know what you have tried but you could start with wiping cache in recovery mode.

spawnlives said:
From what you quoted ( G955USQSS5FSE5 ) you can only down grade to versions that had a version 5 bootloader ( 5th number from right of firmware name ). In your case version 5.
Firmware can be downloaded from sammobile or updato ( websites ). There are other sites as well.
You will need latest Samsung drivers ( for PC ) and Odin version 3.13.3 to flash firmware.
As for network issues don't know what you have tried but you could start with wiping cache in recovery mode.
Click to expand...
Click to collapse
Thank you for the instructions. I guess my only problem is getting Odin to work. I keep getting an error after hitting start.
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I've tried different usb ports and wires, made sure I had samsung drivers but no luck.

DAREALGUMMY said:
Thank you for the instructions. I guess my only problem is getting Odin to work. I keep getting an error after hitting start.
I've tried different usb ports and wires, made sure I had samsung drivers but no luck.
Click to expand...
Click to collapse
Some things to try:
https://forum.xda-developers.com/ga...ning-to-ota-oreo-beta-3-t3920885/post79593856

spawnlives said:
Some things to try:
https://forum.xda-developers.com/ga...ning-to-ota-oreo-beta-3-t3920885/post79593856
Click to expand...
Click to collapse
Finally tried a different PC after everything. It actually begins to attempt to flash but then it fails with a FAIL! (Auth) error.
Is there something I need to do? I run Odin as Admin.

DAREALGUMMY said:
Finally tried a different PC after everything. It actually begins to attempt to flash but then it fails with a FAIL! (Auth) error.
Is there something I need to do? I run Odin as Admin.
Click to expand...
Click to collapse
Auth errors are usually flashing older firmware than on device

DAREALGUMMY said:
Finally tried a different PC after everything. It actually begins to attempt to flash but then it fails with a FAIL! (Auth) error.
Is there something I need to do? I run Odin as Admin.
Click to expand...
Click to collapse
It will also help to know what Odin is saying before the failed message.
What firmware are you try to flash?
After downloading firmware did you unzip the file?