I have an AT&T S4, with MF3 (I think). After installing safestrap successfully, I couldn't install a custom ROM so I kinda gave up and tried to flash it back to stock. I went all over the xda forums, and I attempted to flash about 3-4 stock ROMS using Odin, but none of them work; I always get the error message: <ID:0/005> FAIL! (Auth)
I attempted to flash the MFR.tar file at http://forum.xda-developers.com/showthread.php?t=2413746 and got the same FAIL! message from Odin.
Can anyone please help me?
Check my thread. ... http://forum.xda-developers.com/showthread.php?t=2573080 u can go back to stock MF3 using Odin with MF3.tar files.....and then if u decide to update to MK2 follow second post for guide. .... If u ever brick from MK2 follow third post to unbricked from gtj0 guide method that I edited and replace with MF3> MK2 update. Zip files from first post (OP).... goodluck. ..... Hope this help.. ... If I helped u ..... Hit Thank button. ...
Swyped from MK2 Deadly Venom SS
ted77usa said:
Check my thread. ... http://forum.xda-developers.com/showthread.php?t=2573080 u can go back to stock MF3 using Odin with MF3.tar files.....and then if u decide to update to MK2 follow second post for guide. .... If u ever brick from MK2 follow third post to unbricked from gtj0 guide method that I edited and replace with MF3> MK2 update. Zip files from first post (OP).... goodluck. ..... Hope this help.. ... If I helped u ..... Hit Thank button. ...
Swyped from MK2 Deadly Venom SS
Click to expand...
Click to collapse
I really appreciate your response! You're the only one who's reached out to me (in my desperate hour of need) and I'm thankful!
I checked your thread, downloaded Odin and MF3.tar files. I tried to flash the MF3 files onto my phone using Odin, but got the following error:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl2.mbn
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
As you can see, I'm still having that weird FAIL error. Any ideas what to do?
I went to Best Buy, and they said that it was permanently bricked. I feel so stupid. Anywhere I can sell a bricked phone?
Someone also suggested I install a custom recovery, but since it's bootlocked, I have no idea how to. Is it possible to install a custom recovery on an AT&T phone via Odin?
pwn4g3n3ss said:
I went to Best Buy, and they said that it was permanently bricked. I feel so stupid. Anywhere I can sell a bricked phone?
Someone also suggested I install a custom recovery, but since it's bootlocked, I have no idea how to. Is it possible to install a custom recovery on an AT&T phone via Odin?
Click to expand...
Click to collapse
Are u sure that u have MF3 firmware ... Since u said .... "I think" .....PM me for more help. ... Maybe I can help u........:good:
EDIT: CHECK YOUR PM>>>>>U SHOULD BE OK>>>>>LET ME KNOW HOW IT GO........
Swyped from MK2 Deadly Venom SS
Related
Hey guys,
I think I bricked my phone beyond repair! I attempted to use Odin to Restore my phone to MF3 stock using the tar files that were generously provided. During the Odin restore it failed, not sure what exactly happened. I have used the same files to restore the same mf3 phone on two other occasions. Now my phone won't boot to recovery or Odin mode and just says that firmware update encountered an issue. Please select recovery mode in Kies and try again. The Kies recovery never works and I am left with a phone that is a brick. Will bestbuy be able to do anything through the smart tool? Or anything I can do?
Thanks!
Sent from my iPhone using Tapatalk
You could try here...
http://forum.xda-developers.com/showthread.php?t=2360859
or pull the battery, wait a minute, and put it back and see if you can use the correct key combination to get back into download mode and try ODIN again.
Thanks for the suggestions. But nothing seems to kick it out of this Kies recovery mode. I'm sending it back to samsung. Hopefully they can repair or ship me a new device as I am still under warranty.
Sent from my iPhone using Tapatalk
dtruong23 said:
Thanks for the suggestions. But nothing seems to kick it out of this Kies recovery mode. I'm sending it back to samsung. Hopefully they can repair or ship me a new device as I am still under warranty.
Sent from my iPhone using Tapatalk
Click to expand...
Click to collapse
Same thing happened to me.. I worked for hours and finally about gave up, but tried flashing the I337 PIT file thru Odin in the Pit option.. It said failed but I pulled the battery and rebooted into recovery then restarted.. Google for the pit file.. It's on my computer but if you can't find it I can upload it for you.. Good luck!
Btw, the screen that says "firmware has encountered an issue" should still be able to be recognized in Odin..
I had to get on my computer anyway, so here is the file I used for the PIT box in Odin 3.09.. Hope it works for you!
https://www.dropbox.com/s/fptxnxsqevjhnt9/SGS-I337_16GB.pit
im having a simular problem. I keep getting this error when i try to use odin to restore back to stock.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
iammeHD said:
im having a simular problem. I keep getting this error when i try to use odin to restore back to stock.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Did you do the latest update to MK2?
nerdyblonde said:
Did you do the latest update to MK2?
Click to expand...
Click to collapse
Im not sure what that is, i just wiped my phone and now im stuck at a boot loading screen and i can get recovery/download, and i was told to use odin to flash back to stock
Hello there! I recently had purchased a Samsung Galaxy s4. I did not really enjoy touchwiz. I really wanted Google Play Edition. Anyways, my phone is stuck in ODIN mode with a message saying "Downloading... Do not turn off target!" I know that you can enter download mode and hit cancel to boot. But, my issue is different. Listen. I got safestrap on my s4, and it worked perfectly. I backed up my phone and installed Google Play Edition on the STOCK slot. Turned out, Google Play Edition would not boot up so I went back into safestrap and added a new rom slot. Then I restored my firmware on that slot. I left the stock slot not working... Then I uninstalled safestrap at boot up, not thinking about the stock rom. THIS IS THE BIG MISTAKE. I then rebooted my phone, and I get odin with the error message. I can't get into recovery settings or safestrap of course. I am now stuck with no options on my phone. I try to go to download mode and hit cancel. This did not boot up my phone, only my Google Play Edition which was not working. Now I can't change my rom slot. All I want to do now is go back to touchwiz. I want to restore my phone, but how? I would really appreciate your help!
I was running android 4.3 jellybean on MF3 so I can't load TWRP.
AlwaysBeen said:
Hello there! I recently had purchased a Samsung Galaxy s4. I did not really enjoy touchwiz. I really wanted Google Play Edition. Anyways, my phone is stuck in ODIN mode with a message saying "Downloading... Do not turn off target!" I know that you can enter download mode and hit cancel to boot. But, my issue is different. Listen. I got safestrap on my s4, and it worked perfectly. I backed up my phone and installed Google Play Edition on the STOCK slot. Turned out, Google Play Edition would not boot up so I went back into safestrap and added a new rom slot. Then I restored my firmware on that slot. I left the stock slot not working... Then I uninstalled safestrap at boot up, not thinking about the stock rom. THIS IS THE BIG MISTAKE. I then rebooted my phone, and I get odin with the error message. I can't get into recovery settings or safestrap of course. I am now stuck with no options on my phone. I try to go to download mode and hit cancel. This did not boot up my phone, only my Google Play Edition which was not working. Now I can't change my rom slot. All I want to do now is go back to touchwiz. I want to restore my phone, but how? I would really appreciate your help!
I was running android 4.3 jellybean on MF3 so I can't load TWRP.
Click to expand...
Click to collapse
Download mf3 tar file http://forum.xda-developers.com/showthread.php?t=2504311
Run in odin, your phone should be back up and running.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
[email protected] said:
Download mf3 tar file http://forum.xda-developers.com/showthread.php?t=2504311
Run in odin, your phone should be back up and running.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I dont know why it is failing
AlwaysBeen said:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I dont know why it is failing
Click to expand...
Click to collapse
I think you've got an incomplete flash somewhere. I don't know if this will work but try the mf3 emergency files then flash the tar file again. http://forum.xda-developers.com/showthread.php?t=2526964
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
[email protected] said:
I think you've got an incomplete flash somewhere. I don't know if this will work but try the mf3 emergency files then flash the tar file again. http://forum.xda-developers.com/showthread.php?t=2526964
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
Which file do I exactly download from this link?
AlwaysBeen said:
Which file do I exactly download from this link?
Click to expand...
Click to collapse
You need SGS-I337_16GB.pit. Run this in Odin and it will fix your issue.
And yes I registered just to answer your question.
http://forum.xda-developers.com/showthread.php?t=2404970
bobbigbuns said:
You need SGS-I337_16GB.pit. Run this in Odin and it will fix your issue.
And yes I registered just to answer your question.
http://forum.xda-developers.com/showthread.php?t=2404970
Click to expand...
Click to collapse
I really appreciate the registering just to help me out! Do i load the pit file with the MF3 tars? Or before?
bobbigbuns said:
You need SGS-I337_16GB.pit. Run this in Odin and it will fix your issue.
And yes I registered just to answer your question.
http://forum.xda-developers.com/showthread.php?t=2404970
Click to expand...
Click to collapse
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
It failed =( What can I do? My phone is showing in red text: SECURE CHECK FAIL : PIT
MY BOOTLOADER IS LOCKED, IT SAYS MY WRITE PROTECTION IS ENABLED
AlwaysBeen said:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
It failed =( What can I do? My phone is showing in red text: SECURE CHECK FAIL : PIT
MY BOOTLOADER IS LOCKED, IT SAYS MY WRITE PROTECTION IS ENABLED
Click to expand...
Click to collapse
Do you remember what bootloader you were on?
If you were on anything higher than MF3 you are wasting your time, as you cannot downgrade this far.
MK2 and up requires those specific Odin tars. Since the original post was in January I will assume you were on MK2 at that time.
See here: http://forum.xda-developers.com/showthread.php?t=2663545
Personally, I would just go with the NB1, since root is now out for us. Once you odin the NB1 file, grab the files needed to towelroot, root, install superuser.apk, install safestrap 3.72 and you will probably be back in business
Now... thus all said, I am having a nightmare myself... last night I was listening to music on my I337 NC1 stockly rooted, when all of a sudden it froze... so I pulled the battery (which was fully charged), put it back in, and now my phone won't power up.
Being the geek I am, I grabbed my original samsung udb cable and plugged it into my windows machine... lo-and-behold windows recognized it, but as a completely different device... Qualcom USB or something...
How can I get back to download mode? Or do I need a JTAG? :crying:
kevp75 said:
Do you remember what bootloader you were on?
If you were on anything higher than MF3 you are wasting your time, as you cannot downgrade this far.
MK2 and up requires those specific Odin tars. Since the original post was in January I will assume you were on MK2 at that time.
See here: http://forum.xda-developers.com/showthread.php?t=2663545
Personally, I would just go with the NB1, since root is now out for us. Once you odin the NB1 file, grab the files needed to towelroot, root, install superuser.apk, install safestrap 3.72 and you will probably be back in business
Now... thus all said, I am having a nightmare myself... last night I was listening to music on my I337 NC1 stockly rooted, when all of a sudden it froze... so I pulled the battery (which was fully charged), put it back in, and now my phone won't power up.
Being the geek I am, I grabbed my original samsung udb cable and plugged it into my windows machine... lo-and-behold windows recognized it, but as a completely different device... Qualcom USB or something...
How can I get back to download mode? Or do I need a JTAG? :crying:
Click to expand...
Click to collapse
Sorry to hear about your dilemma. I probably cant help, but why not try.
Question, what do you mean by stockly rooted NC1? Are using the NC1 stock rom but rooted, or are you using another rom? Did you root using the download method or the towel root? Just curious.
I take you have tried to get to download mode using these steps?
Power off the phone completely by removing its battery for 5 seconds.
Re-insert the battery back into its place.
Press and hold Volume Down, Home and Power buttons, all at the same time.
Release the buttons only when the ‘Warning!!’ message appears.
Next, press Volume Up button to confirm that you wish to enter Download Mode.
Your device will now show a green Android with the ‘Downloading… Do not turn off target’ text listed under it.
MatthewPresley said:
Sorry to hear about your dilemma. I probably cant help, but why not try.
Question, what do you mean by stockly rooted NC1? Are using the NC1 stock rom but rooted, or are you using another rom? Did you root using the download method or the towel root? Just curious.
I take you have tried to get to download mode using these steps?
Power off the phone completely by removing its battery for 5 seconds.
Re-insert the battery back into its place.
Press and hold Volume Down, Home and Power buttons, all at the same time.
Release the buttons only when the ‘Warning!!’ message appears.
Next, press Volume Up button to confirm that you wish to enter Download Mode.
Your device will now show a green Android with the ‘Downloading… Do not turn off target’ text listed under it.
Click to expand...
Click to collapse
yeah... tried all that.
Stock Rooted NC1 ROM
Sent from my A110 using Tapatalk
I was updating my samsung galaxy grand prime duos (SM-G531H) with kies, not knowing my cable was broken while the updating the phone disconnected and i ended up with a screen saying "firmware upgrade encountered an issue. please select recovery mode in kies and try again" i changed the cable and decided to flash the update with odin... process went through and the phone booted up normal with the new update installed... now i decided to factory reset so i went into the stock recovery and did but it came up with a bunch of errors which i didn't take note of... i flashed twrp and repaired the file system, wiped system and then i flashed the the firmware together with the pit file on odin once more... the phone booted up normal and i was using it and eveything when i put it to charge and came back 10 mins later the phone was off.... when i powered it on it just stays on the "samsung galaxy grand prime" screen and doesn't boot... it doesn't go into recovery anymore it just hangs whe're it says "recovery is not seandroid enforcing" i tried flashing the firmware with odin again but every single time i tried it keeps failing at...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Removed!!
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I tried the repair firmware together with the pit file and it gets stuck at
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
it's been like that for over an hour now... any help would be much appreciated guys.
No
Try with orignal firmware
nihu.46 said:
Try with orignal firmware
Click to expand...
Click to collapse
I tried everything and nothing seems to work
I also get this problem. Does anyone know how to fix it?
Ghettovybz said:
I tried everything and nothing seems to work
Click to expand...
Click to collapse
Remove kies. Reinstall samsung drivers.
Find and flash TWRP 3.0.0 with odin ( on recovery is not SEAndroid enforcing hold volume up and home for 5-10 seconds. Also flash the Custom Kernel by eyeless95 on the forum, its sepermissive.
u0aol said:
Remove kies. Reinstall samsung drivers.
Find and flash TWRP 3.0.0 with odin ( on recovery is not SEAndroid enforcing hold volume up and home for 5-10 seconds. Also flash the Custom Kernel by eyeless95 on the forum, its sepermissive.
Click to expand...
Click to collapse
What about for SM-G530H?
Do u have the link for the kernel?
After installing kernel what should I do then?
Two ways. Find stock rom in Sammobile and install via Odin (newest). Or try once again install it via Kies. You sould can restore it with Kies, but dont plug phone to computer. Write down S/N or something like that (it's under battery) and model, and Kies will download system
argounaut said:
What about for SM-G530H?
Do u have the link for the kernel?
After installing kernel what should I do then?
Click to expand...
Click to collapse
I have a g531h so I'm not sure. I'm below ten posts so i cant post links.
There are kernels and recoverys in the development section that work fine for your phone .
So a few months back I followed PSouza's guide (https://forum.xda-developers.com/ve...-to-notes-root-install-xposed-unroot-t3411039) to rooting the S7 Edge and everything worked perfectly. As of late, the phone has had many general performance issues and I decided today unrooting may be the best option for right now. So I cracked back open the thread and followed the instructions and low and behold, as always, something had to go wrong. For starters, Odin gives me a fail before it even really gets started (log below).
"<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!"
The phone itself gives a SW Rev check fail after that (in the download mode).
So I thought to myself I'd just keep it in the meantime and just restart it and use it for now, but low and behold I now can't leave download mode. If I restart regularly, I'm brought back to a software update failed screen, and if I switch to recovery mode (? vol up + home + power) I've wiped the cache partition as another forum suggested, but then going to reboot system now... That restart brings me right back into recovery. I currently have the phone off charger in hopes the battery dies and something changes then.
I'm also downloading the very very latest firmware update for the S7 Edge in hopes that maybe Odin will like it a bit better than this one (VZW_G935VVRU2APE1.zip).
Any ideas? Any solution that gets me a working phone again, I'll definitely make a donation to your PayPal! Thanks in advance for any help!
To anyone reading this having the same issue, follow the instructions in this post (https://forum.xda-developers.com/showpost.php?p=71133959&postcount=27) worked like a charm.
zwroberts1 said:
To anyone reading this having the same issue, follow the instructions in this post (https://forum.xda-developers.com/showpost.php?p=71133959&postcount=27) worked like a charm.
Click to expand...
Click to collapse
Have you tried using smart switch? It is a PC app by Samsung which will automatically choose the correct firmware for you, flash it and also unroot your phone. It is the easiest way to do it.
TheSproker said:
Have you tried using smart switch? It is a PC app by Samsung which will automatically choose the correct firmware for you, flash it and also unroot your phone. It is the easiest way to do it.
Click to expand...
Click to collapse
The issue I was having was that Smart Switch wasn't recognizing my phone off the bat, and when I went to emergency recovery, it would say my serial number was incorrect so it wasn't useable for me.
Hello,
I've been on a custom ROM for a few weeks and wanted to go back to Stock now that Oreo has been released.
I'm having difficulty to install stock using Odin 3.1.2 using latest stock firmware.
This is my log from Odin:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
The boxes doesn't show any progression or FAIL.
ME TOO ...Anybody knows Why?... in the past I used Odin several times and ever works fine.. So now I reinstall the drivers, change the PC, USB Cable, etc... and nothing...
I just flash only the BL and this is the result:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin.lz4
Please help us...
coiae said:
ME TOO ...Anybody knows Why?... in the past I used Odin several times and ever works fine.. So now I reinstall the drivers, change the PC, USB Cable, etc... and nothing...
I just flash only the BL and this is the result:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin.lz4
Please help us...
Click to expand...
Click to collapse
Are you using the latest version of Odin?
for me, if i don't flash my personal branded firmware (oreo or nougat) it fails. i must flash only my ITV (italy nobrand). if i try to flash TIM branded ita, it fails
Thanx adj998. You have all reason. My version of ODIN was 3.12.3 and this version don't work with the latest firmware of Samsung S8.
I am looking on Internet.... and that's it... I find a new version of ODIN 3.13.. See attachment
All working perfect. (This link have the last version)
https://www.theandroidsoul.com/download-odin/
adj998 said:
Are you using the latest version of Odin?
Click to expand...
Click to collapse
coiae said:
Thanx adj998. You have all reason. My version of ODIN was 3.12.3 and this version don't work with the latest firmware of Samsung S8.
I am looking on Internet.... and that's it... I find a new version of ODIN 3.13.. See attachment
All working perfect. (This link have the last version)
https://www.theandroidsoul.com/download-odin/
Click to expand...
Click to collapse
Awesome glad it worked for you
Managed to go back to stock but my apps still think I am rooted. Any ideas why? Is it the firmware?
adicken said:
Managed to go back to stock but my apps still think I am rooted. Any ideas why? Is it the firmware?
Click to expand...
Click to collapse
If you've rooted a g950f/g955f, then you've tripped Knox permanently, even if you install stock firmware it will stay tripped. Because of this, any Samsung app that uses Knox such as s-health and s-pay, and so on will say you are rooted, only way to solve this issue is to flash custom rom