Database Users

Unbricking mytouch/g1 ( soft bricks only but no harm trying )

I found a site with someone who bricked their phone but found a loop hole. I have never bricked my phone and hoping i never will but for those who have bricked their phone here are some steps to try to unbrick it! HOPE IT HELPS! SEND FEED BACK!!
So you can’t access bootloader or recovery and the only thing that works is the blue led trick when pressing trackball + power button??
Try the procedure below.
Step 1: Turned Phone off by taking out the battery.
Step 2: Prepared SD card
Put SD card in card reader and formatted it as FAT32, copied the DREAIMG.nbh onto it.
Or try Sapphimg.nbh
Step 3: Put SD card back in phone
Step 4: Hold Vol down + Power + track ball together and put battery to start phone
Step 5: Run update
IF THAT DIDNT WORK!
TRY THIS!
Step 1: Turning Off Your Phone
Because you have a bricked phone, you can't just hold the power button. So if your phone is not already off then you're going to want to take out the battery.
Step 2: Preparing Our SD card
Take out your SD card and put it into an SD card reader or some type of other adapter so that we can view it from our computer. If you cannot view the SD card on your computer then you're going to need a new SD card.
Download DREAIMG-RC29.zip and unzip the file.
Reformat the SD card to FAT32 and copy the DREAIMG.nbh onto it.
Safely eject the SD card.
Put the SD card into your device.
Step 3: Wipe The Phone
Hold home and press the power button.
When you see the image of an ! mark, open your keyboard and press Alt + L if you cannot see any command options.
Do a factory reset by pressing Alt + W or just using the trackball.
When the reset is done, go ahead and hold the camera button and select the reboot system now option with your trackball.
Step 4: Flashing The Phone
Once the grey screen pops up (or the white screen if your phone was rooted with JesusFreke) it will ask you to hit a button to start installing the image…press that button. DO NOT DO ANYTHING TO STOP THIS PROCCESS. It will take about 8-12 minutes.
When the image has completed the installation (it will say completed), go ahead and press the green, red, and menu buttons at the same time. The phone will reboot.
And your done! Your phone is now unbricked!.
The G1 screen will hang there for a good minute or two, but be paticiant, it will boot. Now you have a choice. Try to hack your phone again, because you're in the correct state to have another go, or, you can stick with the official Android. Now if you choose to stick with the official Android, here's what you do.
Step 1: Upgrading to Android 1.0 RC33
Download the file signed-PLAT-RC33-from-RC30.zip
Rename the file to update.zip and copy it to your SD card
Reboot your phone into recovery mode. Power off the phone first and then hold down the Home key while powering it back on.
The recovery mode is finished loading when you see the ! mark inside the triangle. Press Alt + L to display the list of options.
Press Alt + S to flash the file update.zip.
Wait for the update to apply. Your phone may reboot during this process so be patient.
Press Home + Back if prompted to reboot your phone.
Step 2: Upgrading to Android 1.5 CRB43
Download the file signed-kila-ota-148830.de6a94ca.zip
Repeat the steps from above to flash the update file.
Step 3: Upgrade to Android 1.5 CRC1
Download the file signed-kila-CRC1-from-CRB43-FIX.7ca4a1d7.zip
Repeat the steps from above to flash the update file.
Step 4: Upgrade to Android 1.6 DRC83
Download the file signed-kila-DRC83-from-CRC1.c41b93c1.zip
Repeat the steps from above to flash the update file.
PM FOR THE DIRECT WEBSITES!

sad cause this will get locked soon.

domuhhnic said:
sad cause this will get locked soon.
Click to expand...
Click to collapse
why? all we need is someone who can confirm this is true on xda and it will be stickied EVERYWHERE

LOCKED?
domuhhnic said:
sad cause this will get locked soon.
Click to expand...
Click to collapse
Why will this get locked??

Yuppie
oshizzle1991 said:
why? all we need is someone who can confirm this is true on xda and it will be stickied EVERYWHERE
Click to expand...
Click to collapse
Exactly .. but i dont know anyone with a bricked phone so i cant ask them if it works.. if it gets locked (whatever that means) i'll repost it!

id be interested to see if this works... although its assuming you have a dream/g1 .. did you post this in the g1 section?

POST?
digitaljeff said:
id be interested to see if this works... although its assuming you have a dream/g1 .. did you post this in the g1 section?
Click to expand...
Click to collapse
Yes, I have a HTC MAJIC/MYTOUCH .. nope i have not posted it there but i will now

i tried to update radio and now :
So you can’t access bootloader or recovery and the only thing that works is the blue led trick when pressing trackball + power button??
Try all of this methods , but no result..
phone just shows htc magic when i turn it on usually, and nothing!
what can i do?

...
Im still looking of ways to unbrick phones

Possible hint!
Has anyone tried using adb .. Reflashing the recovery img??

...another hint..
kemimarie said:
Has anyone tried using adb .. Reflashing the recovery img??
Click to expand...
Click to collapse
run fastboot boot recovery-image.img or whatever you named your recovery image. It'll display "waiting for device..." message just keep pluging it in, unplugging, popping the battery and eventually your device will respond and boot into recovery.
Someone bricked and i did it... twice trying to flash the eng 2010 SPL. It worked the third time and my device is up and running again with an engineering SPL.
if your device is stuck on the first splash but displays in red "Fastboot USB" message in the upper left corner of the screen, DO NOT power it down. run the above mentioned command and reflash.

deleted... double post.

Found another hint
ch3w said:
confirmed...
-I Connected USB.
-I inserted the battery.
-I booted the phone while holding the HOME key.
-The phone still froze at the first splash screen, but then suddenly, the waiting fastboot command detected the phone and booted the recovery image!
Click to expand...
Click to collapse
try that on your g1/mytouch!

kemimarie said:
try that on your g1/mytouch!
Click to expand...
Click to collapse
this method worked on my second bricked magic, still trying it on the first one but... no luck yet. i had the same problem with both of them tho

kemimarie said:
run fastboot boot recovery-image.img or whatever you named your recovery image. It'll display "waiting for device..." message just keep pluging it in, unplugging, popping the battery and eventually your device will respond and boot into recovery.
Someone bricked and i did it... twice trying to flash the eng 2010 SPL. It worked the third time and my device is up and running again with an engineering SPL.
if your device is stuck on the first splash but displays in red "Fastboot USB" message in the upper left corner of the screen, DO NOT power it down. run the above mentioned command and reflash.
Click to expand...
Click to collapse
fastboot boot recovery?
boot.img and recovery.img are two totally different things.
The recovery (amon_ra is preferred)
The boot.img is where the kernel, ramdisk, etc resides.
you must've meant fastboot flash boot boot.img
or
fastboot flash recovery recovery.img
but not both.

ch3w said:
this method worked on my second bricked magic, still trying it on the first one but... no luck yet. i had the same problem with both of them tho
Click to expand...
Click to collapse
YAAYY!! Im glad to hear you say you had some success!

Binary100100 said:
fastboot boot recovery?
boot.img and recovery.img are two totally different things.
The recovery (amon_ra is preferred)
The boot.img is where the kernel, ramdisk, etc resides.
you must've meant fastboot flash boot boot.img
or
fastboot flash recovery recovery.img
but not both.
Click to expand...
Click to collapse
I just copied and pasted from a website.. THEY did that and it worked for them lol

bricked Mytouch3g
Bricked mytouch3g -- brandnew phone. Just tried to flash cyanogen test3 and everything went fine but then I rebooted and all I have is vodafone boot screen, nothing else works but the blue led which will not load any img. adp doesn't work it never detects a phone no matter what you do. It was the first flash too. Crazy how HTC didn't make a built in hard reset like you have on windows mobile phones. You wonder if they want people to crash there phones so they have to replace them ect etc.

Hello.
My phone has the same problem.
Anything that is needed done. But no no avail.
My phone is brick.
Help help help

Mod edit: not dev related, moved to general

Nexus 7 hard bricked?!

hey
i got my new nexus 7 and wanted to flash a new rom, so i just downloaded this and the flashing tool from this thread.
i didnt root/unlock bootloader or anything else, i just used the tool and did all the steps.
Boot into fastboot,
Wipe my Data,
Install Recovery + Kernel Ability
there were some more steps, but after this my nexus didnt do anything (maybe because of the missing root or the not unlocked bootloader or whatever?!)
it just was stuck in the mode with the android laying on the floor and giving error codes.
so i thought i softbricked it and googled some tutorials to restore a stock rom.
i foundthis and it seemed to work, but it was a bit outdated
i didnt get a .zip from the developers.google.com page, just a .tar, so i couldnt do
Code:
fastboot -w update image-nakasi-jro03d.zip
i just shut down the device then and thought it could maybe already work, because i updated/replaced the bootloader or something like this with
Code:
fastboot flash bootloader bootloader-grouper-3.34.img
but after rebooting it just shows me a completly black screen with a white "Google" in the middle and an open lock on the bottom.
it isnt responding to anything im doing, like pressing on/volume-buttons or connecting usb
the computer cant dedect it via adb with
Code:
fastboot devices
....
what can i do now? do i have to wait, until the battery is dead? this can take days...
i know i did something really stupid
is there any way to restore my nexus 7?
please excuse my bad english and please help me
thank you very much

Hold Power and both volume buttons until it goes off, then power it on while holding both volume buttons. When you see the android, Open Fast boot or a Nexus 7 tool and flash a stock image. You can get them from the Google Dev site. Hope this helps.
Sent from a AOKP'd Nexus 7

MikeTheCat said:
Hold Power and both volume buttons until it goes off, then power it on while holding both volume buttons. When you see the android, Open Fast boot or a Nexus 7 tool and flash a stock image. You can get them from the Google Dev site. Hope this helps.
Sent from a AOKP'd Nexus 7
Click to expand...
Click to collapse
thanks for your help.
when i press power and both volume buttons the screen goes black after a few seconds, but it immediately reboots

Keep holding to volume buttons the entire time. It should go into the boot loader.

MikeTheCat said:
Keep holding to volume buttons the entire time. It should go into the boot loader.
Click to expand...
Click to collapse
ok, thank you, it did. im too impatient :laugh:
i connected it and it was dedected, thank your very much
i went to developers[dot]google[dot]com/android/nexus/images, is this the right google dev site?
i already downloaded this file and i only got a .tar when extracting it, but it seems like i need a .img

You could try and use the nexus toolkit. I haven't tried it, but it should be able to download and flash a stock img to your device from the bootloader.
Good Luck

John_Q said:
You could try and use the nexus toolkit. I haven't tried it, but it should be able to download and flash a stock img to your device from the bootloader.
Good Luck
Click to expand...
Click to collapse
ok, im currently downloading a stock img with "Google Nexus 7 Toolkit v3.2"
lets hope the best, thank you
_______
yes! it works!
thank your very much guys!

[Q] Please help guys

I have installed 4.2.2 on nexus 7. As I had skipped account login at welcome screen, i could not login the account. I altered the apk of login. After factory reset my device has hanged on setup on welcome screen. I tried installing custom rom through stock bootloader but the bootloader says installation failed. How do I solve thia problem guys???

subin.nexus7 said:
don't know the exact steps, but i got it out of the APX mode and into the bootloader.
1. Tablet plugged into computer.
2. Held Volume Down + Volume Up + Power (simultatenously) for three seconds
3. And then released all, and pressed Power again.
4. Tablet booted into bootloader.
I thought that unlocking the bootloader ALWAYS voided the warranty, but in anycase I flashed reflashed ALL stock and locked the bootloader. Will be sending it to ASUS now. Thanks again!
EDIT:
So I wanted to verify that it was a CPU problem, and I downloaded StabilityTest again and ran the CPU load test. It crashed within two minutes, and went into AXP mode again. To get it out of AXP mode, the correct instructions:
1. Plug in the usb into computer
2. Hold Volume Down + Volume Up + Power simultaneously for like 15 seconds
3. The bootloader should show up.
4. If it doesn't, unplug the usb cable, and plug it back in and then repeat the these procedures.
Click to expand...
Click to collapse
Very helpful! I don't have a problem but I've read about others stuck in APX mode. This should be pinned if it works for those stuck in APX. Maybe you should change the thread title to something about APX solution so it draws some attention.

kieso said:
Very helpful! I don't have a problem but I've read about others stuck in APX mode. This should be pinned if it works for those stuck in APX. Maybe you should change the thread title to something about APX solution so it draws some attention.
Click to expand...
Click to collapse
Well... being stuck in APX doesn't necessarily mean your hardbricked. (Corrupt or erased bootloader).
But being hardbricked DOES mean your device will default to APX mode.
To use a mathematical metaphor, one is a SUBSET of the other.
-------
bftb0 has posted an exhaustive list of Nexus 7 button press combos here...
http://forum.xda-developers.com/showthread.php?t=2133986
... which includes how to pro-actively get into APX mode... although until somebody figures how to nvFlash the N7, APX is sort of redundant.
Rgrds,
Ged.

Delete

subin.nexus7 said:
I have installed 4.2.2 on nexus 7. As I had skipped account login at welcome screen, i could not login the account. I altered the apk of login. After factory reset my device has hanged on setup on welcome screen. I tried installing custom rom through stock bootloader but the bootloader says installation failed. How do I solve thia problem guys???
Click to expand...
Click to collapse
I'm sort of confused about the relationship between your edited post and what (apparently ?) kieso quoted, but I'll throw out a few suggestions:
1) AFAIK, there is no way to flash a dev ROM using fastboot (only the boot image of a dev ROM can be flashed this way). You said "bootloader", not "custom recovery" ... so that implies using fastboot. If that is not the case, then your use of terminology is not correct. (It's a computer - reporting details correctly is incredibly important).
2) If you bypass the WiFi login, an account can be added at any time later using the settings menu or simply by launching the Google Play (market) app - there is no need to "alter the apk of login", whatever that means.
3) I would recommend at this point that you start completely over by flashing a factory ROM using fastboot - see the sticky thread about returning to stock using fastboot. If you already have the 4.18 bootloader installed, I recommend you avoid like the plague any operation involving flashing the bootloader.
4) It should be obvious from the trouble that you got yourself into that you should learn what nandroid backups are and that you START USING THEM. The first thing you do after rooting is "make a backup", not "flash a ROM"
good luck

Thanq so much.But still some clarification needed
Now What do I do? My nexus 7 can't pass through at welcome screen saying saying unfortunately setup wizard has stopped. and in recovery{i have no custom recovery, I use bootloader 4.18} i cant flash any rom. I just want to start device any how.. any way.. Is there any way??

subin.nexus7 said:
Now What do I do? My nexus 7 can't pass through at welcome screen saying saying unfortunately setup wizard has stopped. and in recovery{i have no custom recovery, I use bootloader 4.18} i cant flash any rom. I just want to start device any how.. any way.. Is there any way??
Click to expand...
Click to collapse
I guess I am having trouble understanding the sum total of information you have provided - I guess you have omitted some information or mis-stated something. No custom recovery sort of implies a full stock device, but yet you previously mentioned modifying/changing an .apk in /system... normally that would be possible only with a rooted ROM or a custom recovery to do that.
If your tablet is 100% stock, a factory reset of the tablet should allow you to boot once again - at the cost of deleting everything you put on the device, including all files you put on the (pseudo-) SD card.
If that is the case:
- press and hold power+vol-down until the bootloader screen shows up
- use vol-up/vol-down to select "start recovery" and press the power button
- an android lying on it's back should show up; this is the stock recovery splash screen, so
- press power+vol-up simultaneously for about one second - the stock recovery menu should show up
- select factory reset (with vol-up/vol-down) and press the power button.
good luck

bftb0 said:
I guess I am having trouble understanding the sum total of information you have provided - I guess you have omitted some information or mis-stated something. No custom recovery sort of implies a full stock device, but yet you previously mentioned modifying/changing an .apk in /system... normally that would be possible only with a rooted ROM or a custom recovery to do that.
If your tablet is 100% stock, a factory reset of the tablet should allow you to boot once again - at the cost of deleting everything you put on the device, including all files you put on the (pseudo-) SD card.
If that is the case:
- press and hold power+vol-down until the bootloader screen shows up
- use vol-up/vol-down to select "start recovery" and press the power button
- an android lying on it's back should show up; this is the stock recovery splash screen, so
- press power+vol-up simultaneously for about one second - the stock recovery menu should show up
- select factory reset (with vol-up/vol-down) and press the power button.
good luck
Click to expand...
Click to collapse
when you say at the cost of deleting everything, does this include deleting everything in the bootloader because thats what I did when I used the command "fastboot erase bootloader"

Help, I know it's been asked, can't find the answer, can't boot past the LG logo

Please help, I went to update my magisk to 11.6 as it said, everything else is fine. It's rooted has NATFs ROM on it, 3.2 and everything else was otherwise fine. Then, it rebooted to install the Magisk update and here I am stuck with a phone that won't boot past the LG Life's Good screen. The screen dims slightly after the LG logo is displayed and then nothing. Absolutely nothing at all. I can't boot into recovery or bootloader, and the device isn't recognized even though my computer makes a noise as though it's connected when I plug it in to the computer's USB port.
Please help, I'm really stuck here.

sanjsrik said:
Please help, I went to update my magisk to 11.6 as it said, everything else is fine. It's rooted has NATFs ROM on it, 3.2 and everything else was otherwise fine. Then, it rebooted to install the Magisk update and here I am stuck with a phone that won't boot past the LG Life's Good screen. The screen dims slightly after the LG logo is displayed and then nothing. Absolutely nothing at all. I can't boot into recovery or bootloader, and the device isn't recognized even though my computer makes a noise as though it's connected when I plug it in to the computer's USB port.
Please help, I'm really stuck here.
Click to expand...
Click to collapse
Have you tried going to recovery via button combinations?

JeyTruth said:
Have you tried going to recovery via button combinations?
Click to expand...
Click to collapse
Yes, thanks. I tried that. Nothing registers with the power on/volume down nor volume up.
Is the bootloader corrupted?

sanjsrik said:
Yes, thanks. I tried that. Nothing registers with the power on/volume down nor volume up.
Is the bootloader corrupted?
Click to expand...
Click to collapse
Then unbrick the phone by going fastboot mode
Type "fastboot oem lock (or locker)"
*Then shut off the phone.
*Then do a factory reset by the same combination you do when going to recovery.
*after that try going fastboot again and unlock the oem
*with "fastboot oem unlock(or "unlocker" don't remember
Then you should be able to go to recovery.
BE AWARE : your phone my be wiped so make sure you backup.

Just wanted to say I'm on the same rom and did the update too, but I didn't have any issues thankfully.

JeyTruth said:
Then unbrick the phone by going fastboot mode
Type "fastboot oem lock (or locker)"
*Then shut off the phone.
*Then do a factory reset by the same combination you do when going to recovery.
*after that try going fastboot again and unlock the oem
*with "fastboot oem unlock(or "unlocker" don't remember
Then you should be able to go to recovery.
BE AWARE : your phone my be wiped so make sure you backup.
Click to expand...
Click to collapse
I'm a moron. Can I ask for really stupid steps here because I'm kind of nervous about making this worse.
1. I was able to oem lock and unlock, however I still can't get past the LG screen. I can get to fastboot, nothing more
2. I'm sure everything is wiped, I'll worry about later, I just want to be able to get to recovery and nothing is registering at all
3. ADB reboot recovery isn't working at all I get error: device '(null)' not found
Currently, I'm sitting with the device plugged into my computer on fastboot mode displayed on the screen with the command "use fastboot reboot" if the fastboot is available.
fastboot devices shows the following:
LGH918ad448f8 fastboot
Is there a way to get to recovery from fastboot?
ugh, this is so frustrating. Any help would be gratefully appreciated.

sanjsrik said:
I'm a moron. Can I ask for really stupid steps here because I'm kind of nervous about making this worse.
1. I was able to oem lock and unlock, however I still can't get past the LG screen. I can get to fastboot, nothing more
2. I'm sure everything is wiped, I'll worry about later, I just want to be able to get to recovery and nothing is registering at all
3. ADB reboot recovery isn't working at all I get error: device '(null)' not found
ugh, this is so frustrating. Any help would be gratefully appreciated.
Click to expand...
Click to collapse
After you locked the oem. Did you turn off the phone and then factory reset (by pressing volume down and power, after you see lg you then release only power button for a second and press it again)?
Make sure to do this after locking oem and before unlocking oem.

JeyTruth said:
After you locked the oem. Did you turn off the phone and then factory reset (by pressing volume down and power, after you see lg you then release only power button for a second and press it again)?
Make sure to do this after locking oem and before unlocking oem.
Click to expand...
Click to collapse
Okay, did this bit and yes, wiped the data and the screen showed up asking me to do so.

sanjsrik said:
Okay, did this bit and yes, wiped the data and the screen showed up asking me to do so.
Click to expand...
Click to collapse
Alright you can theoretically flash the recovery twrp.img through fast boot, after you reflash the recovery you can go recovery from there.
I think typing fastboot reboot recovery
Check online. I'm not sure exactly.

sanjsrik said:
Okay, did this bit and yes, wiped the data and the screen showed up asking me to do so.
Click to expand...
Click to collapse
I'm taking the battery out.
reinserting the battery
Pressing the power and volume up button and releasing for a second and reholding what do I release and rehold? I am trying to hold the volume up while releasing and reholding the power but I just get the same LG screen and no recovery
Ugh, i"m so sorry for asking for so much help.

sanjsrik said:
I'm taking the battery out.
reinserting the battery
Pressing the power and volume up button and releasing for a second and reholding what do I release and rehold? I am trying to hold the volume up while releasing and reholding the power but I just get the same LG screen and no recovery
Ugh, i"m so sorry for asking for so much help.
Click to expand...
Click to collapse
After you do that button combinations it's going to ask you if you want to wipe or factory reset etc, you choose YES twice!. If you flashed recovery before then it'll take you over there after the choosing yes (it's not really gonna do anything just suppose to take you to recovery)
Edit: Okay let me be clear. When you lock the oem you should do the buttons combination. If you do them successfully then it should take you to a white screen. Asking you about confirmation twice. Then it will wipe and factory reset.
Now when you already have oem unlocked, you do the same procedure and which will take you to white screen then you choose YES twice then it'll take you to recovery (if you have successfully flashed it before)
---------- Post added at 12:41 AM ---------- Previous post was at 12:34 AM ----------
sanjsrik said:
I'm taking the battery out.
reinserting the battery
Pressing the power and volume up button and releasing for a second and reholding what do I release and rehold? I am trying to hold the volume up while releasing and reholding the power but I just get the same LG screen and no recovery
Ugh, i"m so sorry for asking for so much help.
Click to expand...
Click to collapse
Lol, btw it's volume DOWN not volume up.
So don't even lock the oem, try doing the combination properly now
Edit: so if it still doesn't work then try flashing twrp.img through fastboot there is a command I just don't remember. Make sure you have the .img twrp file locally so you can flash it.

JeyTruth said:
After you do that button combinations it's going to ask you if you want to wipe or factory reset etc, you choose YES twice!. If you flashed recovery before then it'll take you over there after the choosing yes (it's not really gonna do anything just suppose to take you to recovery)
Click to expand...
Click to collapse
i did choose yes twice, but when exactly did I flash recovery at this point? You write "IF you flashed recovery" I had recovery on here already but can't get to it
at this point, all I can do is see fastboot if I plug the phone into a cable, put the battery in and hold the volume down button down otherwise, I can't get to anything else but fastboot.
I'm at the fastboot mode
I downloaded the latest recovery twrp-3.0.2-1-h918.img (renamed to image.img), I'm trying the following command to push and flash recovery through bootloader but I get the following error
message:
fastboot flash image.img and I see the following error message:
cannot determine image filename for 'image.img'
What am i doing wrong?
ugh, I'm really sorry for asking so many dumb questions

sanjsrik said:
i did choose yes twice, but when exactly did I flash recovery at this point? You write "IF you flashed recovery" I had recovery on here already but can't get to it
at this point, all I can do is see fastboot if I plug the phone into a cable, put the battery in and hold the volume down button down otherwise, I can't get to anything else but fastboot.
I'm at the fastboot mode
I downloaded the latest recovery twrp-3.0.2-1-h918.img (renamed to image.img), I'm trying the following command to push and flash recovery through bootloader but I get the following error
message:
fastboot flash image.img and I see the following error message:
cannot determine image filename for 'image.img'
What am i doing wrong?
ugh, I'm really sorry for asking so many dumb questions
Click to expand...
Click to collapse
The proper command is;
Fasboot flash recovery image.img
And make sure the twrp file is stored locally from where you started the command prompt.
If it worked and flashed then try: Fasboot reboot recovery
To go to recovery.

I was able to run the following command from fastboot (looked it up):
fastboot flash recovery image.img
I see the following error message:
target reported max download size of 5368...
sending 'recovery' (24092 KB)
OKAY [0.578s]
writing 'recovery'...
FAILED (remote: unknown command)
finished. total time: 0.598s
So, should I try the volume down and power button again?

sanjsrik said:
I was able to run the following command from fastboot (looked it up):
fastboot flash recovery image.img
I see the following error message:
target reported max download size of 5368...
sending 'recovery' (24092 KB)
OKAY [0.578s]
writing 'recovery'...
FAILED (remote: unknown command)
finished. total time: 0.598s
So, should I try the volume down and power button again?
Click to expand...
Click to collapse
Yes, power off phone and try the combination
---------- Post added at 01:05 AM ---------- Previous post was at 12:56 AM ----------
@sanjsrik if still not working then take a look at this;
http://techxat.com/restore-lg-v20-stock-romfirmware-unroot/

JeyTruth said:
Yes, power off phone and try the combination
---------- Post added at 01:05 AM ---------- Previous post was at 12:56 AM ----------
@sanjsrik if still not working then take a look at this;
http://techxat.com/restore-lg-v20-stock-romfirmware-unroot/
Click to expand...
Click to collapse
Ugh, thank you so much for your patience. I did the following:
battery pull
power on, volume down
LG logo finger off for one second on the power button, kept volume down
rebooted into recovery, I'm flashing NATF ROM now
thank you so much I hope this works, all the data and stuff can be recovered, didn't/wouldn't lose much, all backed up. It's installing now.
i sure hope this works
YES, I SEE THE ANDROID boot screen. This thing takes a while to get past but at least it means I'm on the right track.
I thank you a lot brother.

sanjsrik said:
I'm taking the battery out.
reinserting the battery
Pressing the power and volume up button and releasing for a second and reholding what do I release and rehold? I am trying to hold the volume up while releasing and reholding the power but I just get the same LG screen and no recovery
Ugh, i"m so sorry for asking for so much help.
Click to expand...
Click to collapse
I hit this issue on my h910 I extracted the boot image from the ROM flashed it in fastboot after that I was able to access recovery
Sent from my LG-H910 using Tapatalk

I'm sitting here doing nothing waiting for all the apps to reinstall. What a waste of a day. I didn't reinstall Magick, never really used it. Not sure what happened, but at least it wasn't fatal.

sanjsrik said:
I'm sitting here doing nothing waiting for all the apps to reinstall. What a waste of a day. I didn't reinstall Magick, never really used it. Not sure what happened, but at least it wasn't fatal.
Click to expand...
Click to collapse
Yea, happens. Just to be sure. Make sure you keep twrp and supersu stored on SD just in case. And always backup [emoji14]

Thank you
JeyTruth said:
Yea, happens. Just to be sure. Make sure you keep twrp and supersu stored on SD just in case. And always backup [emoji14]
Click to expand...
Click to collapse
I do a daily backup at about 3am to my SD card. Thought about restoring from it, but then realized this is an opportunity to start all over which is something I was leery to do because I didn't want to set the phone up again. Yet, I'm doing it now to see what was causing the awful battery drain.

Stuck in Boot Loop

Have searched the forum but came up empty.
Hoping someone can help.
Purchased the phone used back in December and have been using it as-is. Two OTA updates came through fine. The latest OTA update has it stuck in a boot loop.
- I can get to fastboot with power and volume down buttons but all of the options either turn it off or stick it back in the loop again (Essential logo with powered by Android, NO dot animation)
- Can't see it via "adb devices" since developer mode was likely not enabled
- "fastboot devices" can see the phone but can't change slots or do anything else
I saw two other people who've posted something similar but no solution. Is my phone garbage?
Any help is appreciated.

harpoon said:
Have searched the forum but came up empty.
Hoping someone can help.
Purchased the phone used back in December and have been using it as-is. Two OTA updates came through fine. The latest OTA update has it stuck in a boot loop.
- I can get to fastboot with power and volume down buttons but all of the options either turn it off or stick it back in the loop again (Essential logo with powered by Android, NO dot animation)
- Can't see it via "adb devices" since developer mode was likely not enabled
- "fastboot devices" can see the phone but can't change slots or do anything else
I saw two other people who've posted something similar but no solution. Is my phone garbage?
Any help is appreciated.
Click to expand...
Click to collapse
Damn, that's a bit unlucky, this March update said it would make recovery from a loop after OTA update easier to recover from, which might just have helped you. Sorry not sure how to help fix at present.

you can try flashing one of these https://forum.xda-developers.com/essential-phone/development/stock-7-1-1-nmj20d-t3701681
be sure to pick one with the fastboot images

harpoon said:
- Can't see it via "adb devices" since developer mode was likely not enabled
- "fastboot devices" can see the phone but can't change slots or do anything else
Click to expand...
Click to collapse
A couple of questions:
- Is your BL unlocked (or is OEM Unlocking enabled)?
What happens if you try executing "fastboot flashing unlock"? NOTE: this would WIPE your data if successful.
- Can you get to the Recovery mode? It's when you pick "Recovery" option from fastboot mode, see the lying android with an exclamation sign, then hold Power and press VolumeUp to get to the Recovery menu.

kt-Froggy said:
A couple of questions:
- Is your BL unlocked (or is OEM Unlocking enabled)?
What happens if you try executing "fastboot flashing unlock"? NOTE: this would WIPE your data if successful.
- Can you get to the Recovery mode? It's when you pick "Recovery" option from fastboot mode, see the lying android with an exclamation sign, then hold Power and press VolumeUp to get to the Recovery menu.
Click to expand...
Click to collapse
Thanks for your response.
- I dont belive OEM unlocking is enabled.
- I can get to the fastboot menu, but the recovery mode option just takes me back to the 'powered by android' logo, not the green dead robot.
- When I try fastboot flashing unlock, I get the below error:
=============
FAILED (remote: Flashing Unlock is not allowed
)
finished. total time: 0.013s
=============

yenkoPR said:
you can try flashing one of these https://forum.xda-developers.com/essential-phone/development/stock-7-1-1-nmj20d-t3701681
be sure to pick one with the fastboot images
Click to expand...
Click to collapse
Will this work even though I cannot see the device via adb? AND the device state is "locked".

harpoon said:
- I dont belive OEM unlocking is enabled.
- I can get to the fastboot menu, but the recovery mode option just takes me back to the 'powered by android' logo, not the green dead robot.
- When I try fastboot flashing unlock, I get the below error:
Click to expand...
Click to collapse
Dang... :\ Yeah, the last error means you don't have OEM unlock enabled. So, you can't flash the bts image via fastboot. One last thing I could think of is trying to get to recovery by the button combo. Although, if you are correct in saying you don't have USB debug enabled, it won't do much good, i.e. you won't be able to flash an OTA... :\
While device is OFF, press and hold Volume-Up button while pushing Power button to boot.
Your device will now be in Recovery mode. An Android logo with red exclamation mark should appear on screen. Hold the Power button, then press the Volume-Up button one time to see the recovery menu.

can you try this command on bootloader:
fastboot OEM unlock

harpoon said:
Have searched the forum but came up empty.
Hoping someone can help.
Purchased the phone used back in December and have been using it as-is. Two OTA updates came through fine. The latest OTA update has it stuck in a boot loop.
- I can get to fastboot with power and volume down buttons but all of the options either turn it off or stick it back in the loop again (Essential logo with powered by Android, NO dot animation)
- Can't see it via "adb devices" since developer mode was likely not enabled
- "fastboot devices" can see the phone but can't change slots or do anything else
I saw two other people who've posted something similar but no solution. Is my phone garbage?
Any help is appreciated.
Click to expand...
Click to collapse
Hi. A long time has passed and I want to know if you have solved your problem. I came across the same)

Rudter said:
Hi. A long time has passed and I want to know if you have solved your problem. I came across the same)
Click to expand...
Click to collapse
Nothing ! ..
my ph-1 still into the drawer ! .