So my 16gb Asus Transformer has a very strange problem. I have not seen it mentioned anywhere. When I plug my unit into the supplied charger there is NO indication on the device that it is charging. It takes about 10 hours to fully charge.
Here is the really strange part... When I put the device into the keyboard dock, I get a charge symbol on the battery and it says charging. To make things even more strange the cable and wall wart provided with the tablet quick charges the keyboard dock, light is red then turns green when fully charged (no longer then 2 hours so far).
How could the charger charge the dock no problem but not charge the unit itself? My thoughts were that the dock may seat farther into the tablet then the cord does so I took a small file and took off a little of the plastic on the eee pad connector side, that did not help at all. Any ideas?
I have flashed the latest software update, and I have done a "Factory Data Reset" and it will still not "quick charge" from the supplied charger, only from the dock.
ThePCTech
I got the same problem,i don't have the dock.I see a hole next to the camera but when i charge it there is no light,WTF
sj408 said:
I got the same problem,i don't have the dock.I see a hole next to the camera but when i charge it there is no light,WTF
Click to expand...
Click to collapse
I must admit that I expected to see a charging light on the pad itself, I think the hole you mention may be the light sensor.
When I use the official charger, I get a lightning bolt symbol and it charges fairly quickly. When I used my Kindle charger or an HTC one and plugged the USB into them, I had no indication it was charging and it was really REALLY slow...
Mr.Clark said:
When I use the official charger, I get a lightning bolt symbol and it charges fairly quickly. When I used my Kindle charger or an HTC one and plugged the USB into them, I had no indication it was charging and it was really REALLY slow...
Click to expand...
Click to collapse
The ASUS charger is rated @ 15V 1.2A. Most USB chargers are 5V. USB itself is rated @ 5V. So I donno how it can use 15V via USB. I tried several different chargers with much higher amperage but no luck at all. Quite strange I must say.
Let me clarify, The ASUS Eee Pad has no charging lite on the unit itself. The only indication is in the taskbar on Android 3.0.1. The battery will change from a green battery symbol to a green battery symbol with a lightning bolt on it when it is "Quick Charging".
There are two ways that the device charges, the first is a quick charge (with lightning bolt on batt. symbol), the second is a slower trickle charge (no indication). A quick charge should take about 2 - 3 hours to fully charge. The trickle charge will take up to 12hrs. The ONLY two ways to get a "Quick Charge" is 1. To use the provided charger (came with the unit), and 2. Is to put it in the dock. A trickle charge can be done with ANY other USB port (ie. laptop, desktop, iPod AC adapter, ect.).
My ASUS Eee Pad Transformer will ONLY "Quick Charge" with the dock. The cable provided with the unit will NOT "Quick Charge" my device.
Anyone else have this? If so do you have a fix?
ThePCTech
FIXED!
Ok, so here is the deal...
I ordered a 32gb version and I'm givving the 16 version to my wife. I tried the new plug in the old tablet and the same thing happened. So I thought it MUST be the tablet and NOT the charger as I thought it was.
Looking into the bottom of the tablet I noticed a pin that looked like it was bent. If you look into the socket with the screen facing up. The 4th or 5th pin was bent up and not sitting in the track like it should have been. I compaired this to the new 32gb version. I used a needle to gently move it into place and tried again and it charged as it should with both cables. Newegg offered to replace the unit, but everything else works great on it and, now it chages just fine. I'll just keep it.
ThePCTech
If anyone else is having a problem take a look into the socket of the tablet, it could be a quick fix.
i fixed my charging problem by doing a factory reset.........wow...
Same problem
I have the exact same problem, but mine didn't start until I applied an update from asus.
I think I may have *had* the same problem. I returned my transformer to sears after it would not charge. After my return a clearance sticker was placed on it and now after reading this thread I am considering repurchasing the transformer and getting a new adapter. But I am concerned that it may be something wrong with the tablet itself. This thread leads me to conclude it is the former. But what do you think?
I was not able to charge through the adapter - however, when connected through the USB cord my laptop did recognize it. I did not leave it connected for longer than 10minutes -I guess if i left it in for 12hrs plus I would have a conclusive answer - but to late for that now..
I got the tablet today -it had 5% battery and after trying three outlets it shutdown- it would restart and not get past the homescreen (which had the time and stated to connect the charger and the lock) it would then shutdown.
In the 20 minutes I was able to use my transformer it worked great
sj408 said:
I got the same problem,i don't have the dock.I see a hole next to the camera but when i charge it there is no light,WTF
Click to expand...
Click to collapse
The "hole" next to the camera is the light sensor.
thepctech said:
So my 16gb Asus Transformer has a very strange problem. I have not seen it mentioned anywhere. When I plug my unit into the supplied charger there is NO indication on the device that it is charging. It takes about 10 hours to fully charge.
Here is the really strange part... When I put the device into the keyboard dock, I get a charge symbol on the battery and it says charging. To make things even more strange the cable and wall wart provided with the tablet quick charges the keyboard dock, light is red then turns green when fully charged (no longer then 2 hours so far).
How could the charger charge the dock no problem but not charge the unit itself? My thoughts were that the dock may seat farther into the tablet then the cord does so I took a small file and took off a little of the plastic on the eee pad connector side, that did not help at all. Any ideas?
I have flashed the latest software update, and I have done a "Factory Data Reset" and it will still not "quick charge" from the supplied charger, only from the dock.
ThePCTech
Click to expand...
Click to collapse
Your unit is working correctly. There is no charging indicator on the tablet only on the dock. The tablet show charge status via software in the lower right corner of the display or in setup which will show percentage.
When you connect the unit to the dock, the tablet is charged via the batteries in the dock. The goal is to ensure that tablet is as charged as possible so you can undock and go knowing the tablet is charged. The charging from the dock to the tablet will only occur if the tablet is below 97%. The indicator light on the dock only refers to the charge status of the battery on the dock, not the tablet.
Someone referenced the little light on the front next to the camera, that is not a light. It is an ambient light sensor for the tablet.
The colors for the charge light indicator on the dock are documented in the manual. As I remember it they are <10% quickly flashing orange, 10-50% slowly flashing orange, 50-95% orange, 95%+ green.
I am also having charging problems with my Transformer.
Everything seems to work fine when I used the supplied charger and the USB plug, both with dock and with just the transformer itself.
However I'm presently away and only took the USB cable with me. I've plugged the USB cable into my travel multiplug, which has a usb slot as well and I'm getting no charge at all, either on the dock or the transformer itself. Also the battery is showing that it is actually draining, even while connected to the multiplug. I've also tried connecting both the dock and the transformer to my juicepack (rated at 3.7V, 4,800mAh), but no luck with that as well.
Anyone else had these problems?
Sent from my Transformer TF101 using XDA Premium App
The Transformer will only charge by USB using the supplied wall adapter. Not sure why that is, but that's been my experience.
my problem too.. I got mine yesterday and updated the software straight away. it charged all night and charging worked on both the pad itself and the keyboard.
today it doeasnt..
the cable and the sockets are fine (my pc sees it and did some file transfers) so hardware seems ok. the charger gets quite hot though. does anybody experience the same? maybe its the charger? I wonder if factory reset would help...
browngeek said:
I am also having charging problems with my Transformer.
Everything seems to work fine when I used the supplied charger and the USB plug, both with dock and with just the transformer itself.
However I'm presently away and only took the USB cable with me. I've plugged the USB cable into my travel multiplug, which has a usb slot as well and I'm getting no charge at all, either on the dock or the transformer itself. Also the battery is showing that it is actually draining, even while connected to the multiplug. I've also tried connecting both the dock and the transformer to my juicepack (rated at 3.7V, 4,800mAh), but no luck with that as well.
Anyone else had these problems?
Sent from my Transformer TF101 using XDA Premium App
Click to expand...
Click to collapse
the wall plug that came with the TF is rated for 5V-15V, 2-12A. This is a lot higher than normal USB, which is 5V,1A max. When you plug it into a normal USB jack, you are only in trickle charge mode, and i think it's only with the screen off.
So I left my tab on the multimedia charging dock overnight only to wake up this morning to the battery still at 4%! I did not turn it off though. Has this happened to anyone? The tablet is 10 days old.
redrecordplayer said:
So I left my tab on the multimedia charging dock overnight only to wake up this morning to the battery still at 4%! I did not turn it off though. Has this happened to anyone? The tablet is 10 days old.
Click to expand...
Click to collapse
The fact that it didn't completely drain to 0% makes me think that perhaps you didn't use the Samsung supplied wall plug?
The tab does not need to be powered off to charge, however you need to use a 5v 2a wall plug to charge the tablet. It sounds like your tablet was getting a small amount of juice that kept it from going to zero so perhaps the wall unit you used was 1a or .7a?
If not, I'm not sure what the problem was, but I never power my tab off and it has no problem charging with the supplied equipment.
I was using the Samsung wall adapter, but there is a USB cable extender (cable is too short) in between the adapter and the tab USB cable. I will try again later without the extender and see what happens...
Ok so I bought official charging backplate for my Note 4 and my wife's S5 along with two separate Samsung mini charging plates. Last night we installed the cases and place our phones on their own pad. Mine was in the living room and hers in the bedroom. My phone was at about 50% before I popped it on the charging pad. When I placed it on there I got the charging beep on the phone, green light on the pad and a little message that the phone was charging wirelessly. Same with my wife's phone. Woke up this morning and the battery percentage didn't move on either of our phones. My phone is still at 50%ish and she reported her phone didn't charge as well.
What gives? Any suggestions? Both our phone show charging when on the pads and the green light turns on which means it is charging correctly as per the instruction booklet.
Check the specs on that pad and see how much it outputs. I suspect it is not enough for these larger phones. It may just be enough that they don't lose charge. I use the TYLT Vu Wireless Charging pad and it charges up over night on my Note 4 very reliably.
you need a high power usb connection for charging pads and a good pad.
i have a choetech, itian and a few others which work well IF they are connected to a high power usb port otherwise they dont work. some of them will flash leds or the phone will say connect/disconnect continuously. they need to be connected to a usb wall wart or computer socket or car cig lighter port directly. a usb hub or old usb 1.0 port will not do. a low power charger will also not do but that is less likely. chances are youre not supplying it with enough power and/or not aligning correctly.
So last night I made sure that all apps were closed and that the phone was exactly centered on the pad. This morning it was at 100%. It's a 2a charger that came with the pad and since there is about 50% loss with these charger I'm assuming it charges around 1a once it hits the battery. Seems to work now. Thanks!
phone shouldnt be centered on the pad. the coils are offset by around 3/4-1 inch from the center so the phone will be a bit high (or low depending on how you place it). obviously if you have the 3 coil qi charging mat/rectangular plate instead of the 1 coil disks/plates then you can just throw it on in anywhere and it will charge.
Hi everyone;
I've having an interesting time with my nexus 7 (2012 wifi 32gb).
Before I left on vacation I couldn't get the thing to charge. Looking at the usb port I thought it had become to damaged to make a good connection. So while I was away I ordered a new port assembly. Installed that and still no charging.
Oh the battery cell voltage had gone down to 2.2V so it's in a sleep mode. No problem used a proper lion charger to trickle charge it back to life then further to about 3.8V.
At that point it boots up though the optimization took the charge down to 2% so couldn't do more testing but clearly it worked just fine. However the thing won't charge. Plugging it in to USB it does detect the connection but does not draw any current (as shown by a usb voltage/current monitor). It will show the charge screen, go through 3 cycles of the battery filling animation then shut off.
I check and the voltage is getting from the usb cable into the connector. I traced the ribbon cable from the IO board up to the motherboard and at the other end I also get a nice 5V reading. Clearly the connection from the USB to the device is being made no problem.
At this point I am thinking that maybe I blew the charging circuit. When I was orignally trying to get it to charge before leaving I was applying all kinds of stress to the connector to get it to charge and there was a few times where I think I shorted it (usb monitor showed >3A and the device reset).
Anybody have another theory?
At this point I can't really use it as charging the cell externally is dangerous and not convenient. At this point from what I have seen with my testing and on here if I want to use it I would have to apply 5V to the battery connector (sans battery) which I haven't tried yet.
Hello all,
First thread here and hoping you guys and girls with more experience can help.
Basically I am fitting my nexus 7 2012 in my car but its got the common charging problem where my battery drains faster than I can charge it.
I have ordered a new USB port strip as I've read that can fix it and fingers crossed with that.
My problem/requirement:
1. I want to charge the tablet via the usb port using a hardwired 5V 2A device this will be plugged into a otg y splitter which is then plugged into the tablet.
2. The USB A side of the splitter I want to connect to my cars ECU (it has a USB port) so I can read the data on that (basically a very expensive memory stick)
I wanted to confirm that this would work and id be able to read data at the same time as charging it.
I also wanted to double check I'm not somehow going to send my 5v 2a power down into my ECU and set it on fire
On a side note, if my new USB port replacement doesn't solve the issue of charging the tablet i will have to remove the battery and hardwire it in, will i still be ok with using the USB port for the ecu while charging hardwired with no battery?
Kind Regards
Tim
Getting any USB 2.0 device to take current while hosting is tricky.
Usually it involves talking directly to the PMIC (power management IC).
If it's a fixed installation, why not remove the battery?
It will avoid the grief of the battery swelling up, which is not too unusual for things plugged in all the time.
I've been using a Nexus 7 (2013) for a few years, but just charging on USB.
It started falling out of its nice holder.
That's when I realized that the battery was all puffed up making the back convex.
I cut off the battery cell itself on the metal tabs and soldered in wires to a 4 V 2 A supply.
I found out that the BMS is a bit balky, it refused to turn on.
So I connected it to USB to "charge" it for about 10 seconds.
Then I could turn it on (without the USB).
Ok, I could have bypassed the BMS entirely but that can be a whole 'nother can of worms too.