Database Users

[q] help bricked flash 29

Was going to try one of the new roms with android cooked in. it said i had to install task29. after i ran it through custom ruu i bricked!!!! i was running astraios 1.7 - now im stuck at the white screen with htc in green and it says quietly brilliant underneath in black!
CAN SOMEONE PLEASE HELP!

You're fine my friend, task29 has removed the OS from your device leaving you with only the splash screen and radio. Now you just need to flash the ROM. So go into bootloader (hold volume down while booting) and connect device to PC via activesync. You should see "USB" at the bottom, then run the RUU.exe and you're good to go

phew! thanks a lot!!!

Freeze on HTC logo after MAGLDR install

Hi there! I have a problem after install MAGLDR :/ I connected my HD2 to computer with ActiveSync, runned ROMUpdateUtility from computer, on my phone there was a tricolour screen, then self-reset and phone is freezing on white HTC LOGO. I tried to turn off my phone, remove battery... I'm also turning my phone on with press vol down + power - I have 3 colour screen and now what? PLEASE HELP!

Connect your HD2 to your laptop/pc... boot it while pressing volume down.. wait untill it says usb in the bottom of your screen. Now you can flash HSPL 2.08 and flash a custom or original rom.
I had the same.. gonna stick with RAM roms untill this is nand stuff is sorted out

I have the same problem... but after reflash HSPL 2.08 there will be no change. Could not start the machine.
How can flash rom from pc without booting the machine?
I couldn't understand "Now you can flash HSPL 2.08 and flash a custom or original rom." the second step ...

solved!
I had the same problem.
The issue it's the radio.
install 2.15.50.14
http://www.multiupload.com/QP0IWGY42F

Hi,
After installing hspl 2.08 and then going on to install magdlr, when successful and rebooting it just stayed on the HTC logo screen. It wont reset but it will enter into bootloader. How exactly do i fix this. I tried reinstalling HSPL but it is still stuck on that screen. How would i change this 'problematic radio'?
I relly need to fix my phone so any help would be appreciated! Thanks

sexyseamus said:
Hi,
After installing hspl 2.08 and then going on to install magdlr, when successful and rebooting it just stayed on the HTC logo screen. It wont reset but it will enter into bootloader. How exactly do i fix this. I tried reinstalling HSPL but it is still stuck on that screen. How would i change this 'problematic radio'?
I relly need to fix my phone so any help would be appreciated! Thanks
Click to expand...
Click to collapse
Download a compatible radio (eg 2.15.50 in post above), boot to bootloader (switch off, vol down + power on (keep holding vol down until it boots), connect to pc and when usb shows on screen run the CustomRUU.exe in the radio download. (if there isn't one included you can take any one from a custom wm rom). You flash the radio the same way that you flash a rom.

Thanks for the quick response! I have tried doing this before and just tried the custom RUU posted above but when i run it where it says the image thats on the phone it is blank. Even so i click to update it and both on the phone and pc it stays at 0%. I don't know what to do!

sexyseamus said:
Thanks for the quick response! I have tried doing this before and just tried the custom RUU posted above but when i run it where it says the image thats on the phone it is blank. Even so i click to update it and both on the phone and pc it stays at 0%. I don't know what to do!
Click to expand...
Click to collapse
Are you sure you have HSPL installed properly. In bootloader mode, check the spl version - it should show as 2.08.hspl, not 2.08.0000 or any other hspl version.

In bootloader mode it says SPL 2.08.0000? When installing it i did select the HSPL 2.08?? What should i do? Thanks

sexyseamus said:
In bootloader mode it says SPL 2.08.0000? When installing it i did select the HSPL 2.08?? What should i do? Thanks
Click to expand...
Click to collapse
I had your problem and for some reason when I first ran hspl the first time and put 2.08 on my phone it said it worked but it didn't actually do anything.
Just reinstall 2.08 HSPL on your phone and then run MAGLDR.

Similar Scenario
I installed 2.08.HSPL - confirm at boot loader screen
I installed MAGLDR 1.13 with success
Flashed HD2_Core_Droid_Desire_HD_V1.5_NAND_ONLY_LEO1024_TMOUS to my phone with success
Phone worked fine for about a day and a half and froze up
Pulled battery and restarted to white screen
I can't seem to roll back the SPL, reinstall the MAGLDR, or install a different radio.
ROM Update Utility appears to start to work and phone restarts and I get an error message that the image is corrupt.
Any ideas?

[Q] Device do not Reboot after NAND Flash

Hello,
I tryied to move my HD2 from WM to Android using the NAND Flash method.
After having run the ROMupdateutility and had a "successfull completed" message, the phone is restarting and get stuck in the reboot on a white screen with the green HTC letters.
The USB is not working anymore.
Anyway to recover ?
Thanks in advance for your help.

Correct radio version? Correct spl?
What was your entire process?

i had this problem too and it was because i didn't have the correct HSPL so check if that's ur problem

thanks for your feedback.
I was also thinking that it might HSPL issu (I had the 3.03), but as I can not get any USB connection I have no clue how to change to 2.08 per exemple.
Have you any idee ?

- Start your phone in the bootloader (Power button + volume down button, keep them pressed at the same time till you get the bootloader screen)
- Connect your usb cable and flash the original 1.66 HTC ROM.
Then try to flash the HSPL and MAGLDR again.

Thanks for the tip it worked fine (got the wrong hspl...)

[Q] What i can do please?

Hi everyone! At first sorry because my english is not better than my french
My problem: I have an HTC hd2 with a white screen and the SPL 1.42.0000 (i can go to bootloader). I google it and can't find any solution, i tried to instal HSPL (with hspl2/3/4) without success (usb fail connection) i have the same error with an task29, and an hd2toolkit. I tried to instal from sdcard but i have the error "radio v2 fail".
I think this is a problem at height of XDA developers ^^
PS:I tried to change Computer or usb port and execute as administrator but nothing...
If you coul help me it will be realy nice.

is the phone recognized in device manager? If not its a driver problem.
also do the usual ( verify its not the usb cable, try different usb port,) if drivers are ok

thank you for your help
The computer recognize the device but without OS (white screen) i can't do anythings with Activesync, i tried other computers and other usb port/cable but nothing. I think isn't a driver's problem because the instalation with sd card don't work.

Anis92 said:
The computer recognize the device but without OS (white screen) i can't do anythings with Activesync, i tried other computers and other usb port/cable but nothing. I think isn't a driver's problem because the instalation with sd card don't work.
Click to expand...
Click to collapse
Don't understand what you mean by "white screen"?
Try installing a stock winmo for you device to make sure everything is ok...

i tried to instal an official htc rom from sd card but it doesn't work, by "white screen" i just wanted to say that when i turn on my phone the screen is white.

It sounds like you have done a Task 29 and you do not have a ROM on your HD2 right now. This is why you just boot to the white screen.
You do npot have to use Active Sync or Windows Mobile Device Center to flash via RUU. You just have to have them installed because the haqve the USB drivers for the HD2's WINCE Bootloader in the programs and they install the drivers when you install the program.
The drivers in Active Sync and WMDC allow you to have a HTC Sync connection in the bootloader. Just boot into the bootloader by holding down the volume down button while powering on yuour HD2. Next connect your HD2 to your computer via USB cable. Wait and watch for the Serial in the white bar of the bootloader to change to USB. When you see USB you can run a RUU.
Now to address your 1.42.0000 SPL, this is a older SPL version and you may have to keep trying different RUUs until you get one that will flash. Just make sure if you have a T-Mobile HD2 that you do not flash any radio version below 2.08.50.?? or any radio version that has a 51 in the radio where the 50 is in the first radio I mentioned, or you will brick your T-Mobile HD2. Look for the radio version in the RUU name it will be there.
Sometimes the HD2 develops what is referred to as a "stuck radio" when they have these early SPL versions like yours. This is why I say you may just have to keep trying different RUUs until you find one that will flash.

[Q] Stuck in MAGLDR 1.11

Hi!
I've been using an Andriod NAND for like 2 years now and decided to upgrade to IcecreamSandwich. I installed HSPL 2.08 which I believe I had before anyway. Then I tried updating my radio but I get connection error 262. Apparently my phone wouldn't synch with WinMobileDeviceCenter. When I bootload I get serial and when I plugin it changes USB. But device doesn't get recognized. after rebooting I can start my Android no longer - MAGLDR 1.11 says ...boot mount failed. So I'm stuck in MAGLDR 1.11 and I can't ever restore to WinMobile original ROM. Any ideas?

slickie said:
Hi!
I've been using an Andriod NAND for like 2 years now and decided to upgrade to IcecreamSandwich. I installed HSPL 2.08 which I believe I had before anyway. Then I tried updating my radio but I get connection error 262. Apparently my phone wouldn't synch with WinMobileDeviceCenter. When I bootload I get serial and when I plugin it changes USB. But device doesn't get recognized. after rebooting I can start my Android no longer - MAGLDR 1.11 says ...boot mount failed. So I'm stuck in MAGLDR 1.11 and I can't ever restore to WinMobile original ROM. Any ideas?
Click to expand...
Click to collapse
if you put the phone in bootloader (4 colors Screen - HSPL 2.08 exc..) and show up USB when you connect it to the PC, it should be recognized from the application flasher, no PC.
Try to go in bootloader and when you connect the phone to your pc and when show up USB try to upgade and flash MAGLDR 1.13, (no MAGLDR 1.11 the old one) the last one.
Are you sure you used the right Radio for Leo?

thanks
eclyptos said:
if you put the phone in bootloader (4 colors Screen - HSPL 2.08 exc..) and show up USB when you connect it to the PC, it should be recognized from the application flasher, no PC.
Try to go in bootloader and when you connect the phone to your pc and when show up USB try to upgade and flash MAGLDR 1.13, (no MAGLDR 1.11 the old one) the last one.
Are you sure you used the right Radio for Leo?
Click to expand...
Click to collapse
When I try updating either the radio or MAGLDR in the install instructions there is this step2 where I have to establish an activesynch with my phone. I can't. So when I run the update it starts but progress stays at 0% both on PC and phone screen. After a few minutes I get error 262.
I'm trying to install radio 2.15 from Jayce Ooi's Paradise

Forget about active sync, you will never get an active sync connection unless win mo is running,, ,that'snot what the instruction to "get an active sync connection" means. It means get a USB connection, which uses the active sync drivers.
Try different usb ports,,do not use a front mounted usb port,only theones inthe back of the machine.

samsamuel said:
Forget about active sync, you will never get an active sync connection unless win mo is running,, ,that'snot what the instruction to "get an active sync connection" means. It means get a USB connection, which uses the active sync drivers.
Try different usb ports,,do not use a front mounted usb port,only theones inthe back of the machine.
Click to expand...
Click to collapse
Why do I get this connection error then?
I did try different USB ports. Even tried different PCs. Same thing.

slickie said:
When I try updating either the radio or MAGLDR in the install instructions there is this step2 where I have to establish an activesynch with my phone. I can't. So when I run the update it starts but progress stays at 0% both on PC and phone screen. After a few minutes I get error 262.
I'm trying to install radio 2.15 from Jayce Ooi's Paradise
Click to expand...
Click to collapse
find another radio from XDA for HTC HD2, "radio 2.15? What this mean? from Jyce Ooi's Paradise" do not mean anything, I know Jayce and he is an amateur, not master.
You don't answer on questions given to you, if you want help, do you flash from bootloader? turn-off phone, keep pressing volume-down, press button on?
In bootloader, when you connect to pc, show up USB on the bottom of the screen?

eclyptos said:
find another radio from XDA for HTC HD2, "radio 2.15? What this mean? from Jyce Ooi's Paradise" do not mean anything, I know Jayce and he is an amateur, not master.
You don't answer on questions given to you, if you want help, do you flash from bootloader? turn-off phone, keep pressing volume-down, press button on?
In bootloader, when you connect to pc, show up USB on the bottom of the screen?
Click to expand...
Click to collapse
The same thing happens even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship). What question haven't I answered? Yes, I flash from bootloader and yes USB shows up on the bottom when I connect it to the PC. When the updating of the ROM image starts there is no progress - neither on the instalator, nor on my phone (it shows HTC and a progress bar with 0%). After a couple of minutes I get Error 262 and "The ROM update utility has encountered a communication errors during update process."
Is my phone bricked?

slickie said:
The same thing happens even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship). What question haven't I answered? Yes, I flash from bootloader and yes USB shows up on the bottom when I connect it to the PC. When the updating of the ROM image starts there is no progress - neither on the instalator, nor on my phone (it shows HTC and a progress bar with 0%). After a couple of minutes I get Error 262 and "The ROM update utility has encountered a communication errors during update process."
Is my phone bricked?
Click to expand...
Click to collapse
Bricked mean dead, no life at all, your still alive but there is some errors, you should be happy to turn-on the phone in bootloader and usb be recognized. You have to try flash ONLY Radio 2.15.50.14.
If you can't flash the radio which I told you try to erase your rom with this tool.

you can update you magldr 1.11 to 1.13
you can update you magldr 1.11 to 1.13:highfive:

even with the original radio (RUU_Leo_HTC_WWE_EastEurope_1.66.479.2_Radio_CRC_S igned_15.32.50.07U_2.07.51.22_2_Ship
Click to expand...
Click to collapse
thats not a radio, thats a rom that includes a radio, but also includes an spl, , 1.66.0000
Are you SURE it still says x.xx.HSPL in bootloader? because hanging at 0% is very often associated with not having hspl installed.

samsamuel said:
thats not a radio, thats a rom that includes a radio, but also includes an spl, , 1.66.0000
Are you SURE it still says x.xx.HSPL in bootloader? because hanging at 0% is very often associated with not having hspl installed.
Click to expand...
Click to collapse
exactly, I forgot about that!
Also if you really have x.xx HSPL is no more a problem of you Phone but of you PC, so try different OS, even XP, and still trying. IS NOT THE PHONE.