Hi,
Sorry if this has been asked but I couldn't find an answer.
Is there a way to get S-Voice working when the screen is off and locked with a pattern/pin using a bluetooth headset? When I press the call button on the bluetooth headset to activate voice commands to the phone, I can't get S-Voice to work. It seems like the call button wakes up the phone. S-Voice works when I put the phone near me and just say "Hi Galaxy", but I would like to say "Hi Galaxy" through the bluetooth mic. I've tried 4 different pairs of bluetooth headset, but they all don't work with S-Voice. Is there a setting I'm missing? Any way of getting around this? Or is there a bluetooth headset that will work with S-Voice when the phone is locked?
Thanks
Related
i have an HTC wizard with WM5 and i am using a plantronic bluetooth headset that works great except that when i press the button on the headset i cannot make the phone activate the windows built in voice dialing. The button works fine to comnad the phone to hang up ans answer a call. does anyone know ho to have the bluetooth headset button activate the builting voice dialing ?
Hold that same button in that you use to answer/hang up until you hear a beep. Then you will see your phone switch to the voice dialing screen and you will hear one more beep. After that just speak the command you want to execute and the system will re-play the command back to you if it recognizes it. Works great on my 640!
I am using a Plantronics 510 BT headset, but i can't figure out how to get the voice activation working.
I beginning to think that it is not supported, read the manual and afaik it doesn't mention the subject at all.
Has anyone got it working yet?
Tiemen said:
I am using a Plantronics 510 BT headset, but i can't figure out how to get the voice activation working.
I beginning to think that it is not supported, read the manual and afaik it doesn't mention the subject at all.
Has anyone got it working yet?
Click to expand...
Click to collapse
I am not sure I understand your question but I use a SonyEricsson stereo BT headset and when I press the "answer" button on the headset (when phone is not ringing) the "Voice Speed Dial" program comes up.
It does the same with all my jabra
Yes the voice dial function to dial numbers and startup programs is what I meant.
I got it working now
Apparently I have to hold down the button for a second or two to make it work.
Next time I should try a little harder to figure it
anonimo said:
I am not sure I understand your question but I use a SonyEricsson stereo BT headset and when I press the "answer" button on the headset (when phone is not ringing) the "Voice Speed Dial" program comes up.
Click to expand...
Click to collapse
Hi,
I've got a SE BT HBH-660 and when I push the asnwer button, I4ve got the "beep beep" in the speaker telling me that the Headset try to connect to the phone, but for some reason the Phone does not wake-up each time.
To make the voice dial working I need to ON/OFF the BT stack on the phone side.
When my SE BT headset is on and I make a phone call, not all the time the phone connect to the headset.
Did someone figure out the same behaviour ?
If yes how does it solve this ?
I have had a Jabra BT Headset for a couple of years and it works well. I have recently purchased a XCarLink with BT and am now using this in my car instead of the headset. One thing that I liked about the headset was how it worked with M$ Voice Command - i.e. press the 'Talk' button and Voice Command would start and you could say 'call xxx' etc. With the XCarLink if I press the 'Talk' button this justs stops any music that was playing but doesn't start Voice Command.
Is there any tweak I can apply to get this behaviour?
Andy
More testing......
I have been doing some more testing with this as the Jabra BT headset stopped activating Voice Command...
Anyway I have tested a couple of different versions of Voice Command (1.6.19214 & the one from the Diamond 1.6.19581) and both behave the same. If A2DP Joint Stereo is enabled (HKLM\SOFTWARE\Microsoft\Bluetooth\A2DP\Settings - UseJointStereo=1) then the 'Talk' button on the BT headset no longer activates Voice Command. If Joint Stereo is disabled the 'Talk' button activates Voice Command (after a soft-reset).
I haven't had time to check the behaviour with the XCarLink but I will post the results when I do.
If anyone has any experience with this or knows a fix then I'd appreciate it.
Andy
Anyone been able to get voice dialling working from the Xcarlink? I just bought one and am having the same problems.
Can someone verify if you connect a bluetooth device, hold down the button on the bluetooth, will the nexus one prompt to say a command and say for example "call john doe"
-Tortri
i cant find my bluetooth headset or i'd try... ill tell you it didnt use to work on my g1 though
It did not work with my Jabra HALO BT650s. I hear a tone on the headset but the phone does not do anything.
Damn..
Thanks guys!
I have a Plantronics Voyager Pro headset. I've used this with my previous phone, a BB 8900. When the headset is on, it connects to the MT4G and if I make a call, it will automatically use the headset. However, if the headset is on and I recieve a call, a menu opens on the phone and askes where to send the audio. I'd like to set it so that it always chooses the headset if it's on. That's how the 8900 used to work.
Right now, once I answer the call, there's a pause while I select the Voyager Pro out of the menu. Does anyone know how to set this?
Thanks,
Dave
l've found that if you depress the headset button instead of touching the screen during the ring, your phone will answer and use the BT headset without the prompt.
If you touch the screen first, you're screwed.
Hey, thanks! I didn't even think of that. I'll give it a try. I was used to my BB automatically connecting to the BT if it was on. You get a big "Thanks" button for that one.
Dave