I tried searching, but it appears to be broken most of the day today. I did try searching page by page, but didn't get any results.
My brand-new S4 is softbricked apparently. From stock, two night ago, I rooted the phone based on this guide.
I then installed GooManager and installed the TWRP 2.3.6.1 recovery manager. All seemed fine. I was going to install a custom ROM, but decided to back up the phone first. So I booted to recovery and made a backup. I rebooted and all was fine. Then I rebooted to recovery to wipe the phone. I went into the wipe menu and selected Delvik Cache, and a couple more options but I can't remember which. I know I did have USB-OTS (or whatever it is) and that didn't work, so I undid that. I did not have SD Card selected.
The backup appeared to work fine. I rebooted and the phone gets to the "Samsung" screen with the small lock that says, "Custom" under it. That's as far as it gets.
I found this thread to restore the stock. However, when I tried to connect the phone in Odin mode, it will not recognize the phone. The PC recognizes the phone (it makes the noise) and Kies sees the phone, but won't do anything with it. It detects that a phone is connected and tries to identify the device, but can't.
The PC detects my wife's S4 just fine. I'm using the same cable.
BTW, if I try to boot to recovery mode, I get the Samsung lock screen (the same one it hangs up on), then a black screen for a few seconds. Then it goes back to the Samsung lock screen and just sits there. Oh. BTW, the phone does appear to go into download mode just fine. Hitting the Vol Dn button to cancel, does reboot the phone.
So I'm looking for help trying to get Odin to detect the phone. Any suggestions?
BTW, the phone will enter download mode just fine and the Vol Dn button does work to reboot the phone (though it still locks up during the boot sequence).
re: kies
Yippee38 said:
I tried searching, but it appears to be broken most of the day today. I did try searching page by page, but didn't get any results.
My brand-new S4 is softbricked apparently. From stock, two night ago, I rooted the phone based on this guide.
I then installed GooManager and installed the TWRP 2.3.6.1 recovery manager. All seemed fine. I was going to install a custom ROM, but decided to back up the phone first. So I booted to recovery and made a backup. I rebooted and all was fine. Then I rebooted to recovery to wipe the phone. I went into the wipe menu and selected Delvik Cache, and a couple more options but I can't remember which. I know I did have USB-OTS (or whatever it is) and that didn't work, so I undid that. I did not have SD Card selected.
The backup appeared to work fine. I rebooted and the phone gets to the "Samsung" screen with the small lock that says, "Custom" under it. That's as far as it gets.
I found this thread to restore the stock. However, when I tried to connect the phone in Odin mode, it will not recognize the phone. The PC recognizes the phone (it makes the noise) and Kies sees the phone, but won't do anything with it. It detects that a phone is connected and tries to identify the device, but can't.
The PC detects my wife's S4 just fine. I'm using the same cable.
BTW, if I try to boot to recovery mode, I get the Samsung lock screen (the same one it hangs up on), then a black screen for a few seconds. Then it goes back to the Samsung lock screen and just sits there. Oh. BTW, the phone does appear to go into download mode just fine. Hitting the Vol Dn button to cancel, does reboot the phone.
So I'm looking for help trying to get Odin to detect the phone. Any suggestions?
Click to expand...
Click to collapse
Try opening taskmanager in windows ( run >taskmgr ) and before you plug the phone into
usb on your computer end the KIES process in task manager, Kies should not be running
when you plug the usb from phone to computer.
What I have done a long time ago is to uninstall KIES as well as all the samsung usb drivers,
then I downloaded and installed the official Samsung usb drivers from here: http://downloadcenter.samsung.com/c...ng_USB_Driver_for_Mobile_Phones_v1.5.14.0.exe
after doing that I have never had any more issues with Odin flashing.
Good luck!
Misterjunky said:
Try opening taskmanager in windows ( run >taskmgr ) and before you plug the phone into
usb on your computer end the KIES process in task manager, Kies should not be running
when you plug the usb from phone to computer.
What I have done a long time ago is to uninstall KIES as well as all the samsung usb drivers,
then I downloaded and installed the official Samsung usb drivers from here: http://downloadcenter.samsung.com/c...ng_USB_Driver_for_Mobile_Phones_v1.5.14.0.exe
after doing that I have never had any more issues with Odin flashing.
Good luck!
Click to expand...
Click to collapse
Kies is not running in the background. I couldn't get either phone to be recognized by Win7 originally. However, once I uninstalled the driver and Kies, rebooted and re-installed both, I could get Kies and Windows to see the phones. BTW, Linux always sees both phones.
So I'll try your suggestion, and let you know.
I followed your suggestions. I uninstalled the drivers and Kies. Reboot and install drivers. I connected my phone and Odin didn't see it. I connected my wife's phone and windows did the "new hardware found" thing and installed the drivers. As soon as that was done, Odin recognized her phone. I unplugged her phone and plugged mine in and it doesn't see it.
It's almost like the phone doesn't get far enough into the boot process for the computer to recognize anything. It hasn't booted far enough, or something like that.
What firmwire is it on?
Sent from my SGH-I337 using XDA Premium HD app
MDL firmware as installed when I bought it (I got lucky).
My Odin is 3 v1.85.
USB drivers are SAMSUNG_USB_Driver_for_Mobile_Phones_v1.5.25.0-retail
Yippee38 said:
MDL firmware as installed when I bought it (I got lucky).
My Odin is 3 v1.85.
USB drivers are SAMSUNG_USB_Driver_for_Mobile_Phones_v1.5.25.0-retail
Click to expand...
Click to collapse
And you are sure it didn't self update on it's own to mf3? Your Odin and drivers seem right, however kies/Odin don't support mf3.
Sent from my SGH-I337 using XDA Premium HD app
---------- Post added at 10:27 PM ---------- Previous post was at 10:23 PM ----------
If you're still on MDL and can get into recovery, Mount to usb and throw a ROM onto your internal; or use a sdcard and put it in your phone and flash a new system. Possibility your nandroid is broken, it can happen.
Sent from my SGH-I337 using XDA Premium HD app
I don't think so. Every time the update message came up, I just hit the home screen button to go away from it. I don't see how it could have.
I was under the impression that it wouldn't update if the phone was rooted, but maybe I'm wrong about that.
I guess, if it did update, I'm completely screwed, right?
And is there anyway I can find out if it did update?
Yippee38 said:
I don't think so. Every time the update message came up, I just hit the home screen button to go away from it. I don't see how it could have.
I was under the impression that it wouldn't update if the phone was rooted, but maybe I'm wrong about that.
I guess, if it did update, I'm completely screwed, right?
Click to expand...
Click to collapse
Only way it won't update to MF3 If you already had a custom rom on it , but if you rooted it while on MDL and didn't flash a custom rom then update will go in automatically!
Damnit. That sucks.
I guess I'll try the BB restore method. Hopefully, it will work. Thanks for the help all.
Well, good news and bad news.
The good news is that I've got the phone back to stock MDL!!!! <whew!> The bad news is that I'm an idiot.
Where I screwed up was that when I connected the phone, I had only done the VolDn, Home and Power button into download mode. What I didn't do was hit the VolUp from that screen to actually get into download mode. As soon as I did that, Odin recognized it. I was then able to use this method to reflash it with stock MDL. Now I'm back to stock and with MDL.
Hopefully, this if somebody else forgets this important step, this thread will help them.
Thanks to everybody for the help though! It got my mind thinking the right way to find the solution.
Yippee38 said:
I don't think so. Every time the update message came up, I just hit the home screen button to go away from it. I don't see how it could have.
I was under the impression that it wouldn't update if the phone was rooted, but maybe I'm wrong about that.
I guess, if it did update, I'm completely screwed, right?
Click to expand...
Click to collapse
You can only stop the update temporarily, in fact just pressing the home screen doesn't stop the process and it'll eventually force update even with the screen off at idle. Just a root won't stop the updating, unless you froze the necessary processes or flashed a different ROM and framework it'll find a way to update.
Sent from my SGH-I337 using XDA Premium HD app
---------- Post added at 12:34 AM ---------- Previous post was at 12:32 AM ----------
Good job at getting it back and up! Note make sure it won't update on you.
Sent from my SGH-I337 using XDA Premium HD app
Br4nd3n said:
You can only stop the update temporarily, in fact just pressing the home screen doesn't stop the process and it'll eventually force update even with the screen off at idle. Just a root won't stop the updating, unless you froze the necessary processes or flashed a different ROM and framework it'll find a way to update.
Sent from my SGH-I337 using XDA Premium HD app
Click to expand...
Click to collapse
I'm very worried about that now. I rooted my wife's phone. She doesn't want a custom ROM. I told her not to update it, but once it does, I have problems. I have to figure out which processes to freeze to prevent the update apparently before it tries to do it itself. At least she knows not to manually update it.
I found the stuff I needed to do to block the update on my wife's phone. All is good.
Related
ok guys, i have unbricked my vibrant before after the OTA update about 5 weeks ago. i am pretty new at this smart phone stuff, but was pleasantly surprised i was able to get odin to fix the brick. about an hour ago i launched the stupid VooDoo in the OCLF app and the phone now will go as far as the animated galaxy "S", then go blank. i attempted the Odin flash about 5 times now with the same result each time, just boots up past the vibrant screen to galaxy S then goes blank. when the phone restarts or reboots after the odin flash a message in red reads DATA WIPE FAILED between a few yellow text lines. when i try to reinstall packages through boot screen i get the same message i got after the OTA brick, E:Can't open /sdcard/update.zip now the phone was rooted with the OCLF before i launched VooDoo. can somebody help me out?!?
Odin back to stock. That should fix it.
http://forum.xda-developers.com/showthread.php?t=734475
jnutz said:
Odin back to stock. That should fix it.
http://forum.xda-developers.com/showthread.php?t=734475
Click to expand...
Click to collapse
I second this comment. Flashing back to stock shall help. I've soft brick my phone and unbricked it recently.
Sent from my SGH-T959 using XDA APP
www.goteamfriday.com
Anybody else have an suggestions?? like i said in OP i have tried to flash back to stock, about 5-6 times now, all with the same result. phone goes blank after galaxy S screen and music. thanks
As mentioned in a million threads, you need to flash Eugene's "froyo that doesn't brick." Then flash whatever firmware you want.
flashed the froyo successfully from eugene. cool set up, major issue though, i have no application storage now. there are a ton of apps in manage apps and i cannot uninstall any of them. can i fix this somehow??
i'm going to try flashing froyo back in it so it works, not select repartition. then restart odin, select repartition and flash the old vj12 rar and see if that works
Never seemed to get the answer to this. What is the purpose of "Eugene's froyo that doesn't brick?"
Why do some people suggest flashing that, before they odin?
Did eugene take everything down from xda, I can't even find that anymore.
i actually found what i though was the froyo that doesn't brick but it was actually his jk2 version. i clicked Eugene's link on one of his posts and it took me to his site and thats were i got it. i did some searching and actually found the "froyo that doesn't brick", it fixed my baby! i couldn't do anything once flashed but i was then able to flash back to jdf then j16 and all is well. i have flashed like 10 roms into her since this weekend with success, i am back to running j16 with some extras as the games i play don't support 2.2
I'm trying to use Odin but my pc (win xp) is not recognizing my phone. Should i try another pc with vista or win7?
Did you install the drivers
Sent from my SGH-T959 using XDA App
spyda23 said:
I'm trying to use Odin but my pc (win xp) is not recognizing my phone. Should i try another pc with vista or win7?
Click to expand...
Click to collapse
+1 for the drivers.
spyda23 said:
I'm trying to use Odin but my pc (win xp) is not recognizing my phone. Should i try another pc with vista or win7?
Click to expand...
Click to collapse
Check your driver and be sure you phone is in download mode.
jackhuny said:
Check your driver and be sure you phone is in download mode.
Click to expand...
Click to collapse
When i'm in download mode, it doesn't recognize it. When i'm in recovery mode, Odin recognizes it. If i turn my phone on and plug it in, my pc recognizes it, drivers are ok.
Any answers, i could really use the help
what version of Odin are you running? not that it should matter. try pulling the batt, hold volume up and down, insert batt while volume buttons are pressed then plug in USB and wait for it to go into download mode then release buttons. see if Odin recognizes it then.
try a different cable too if above doesn't work
Turn your phone off open odin hold down volume up and down,now plug in the usb this will get you into dl mode now you need to flash Froyo ~~~That does not Brick! rom with odin. Right after you flash that get back into download mode open odin first then with the phone ( power the phone off give it a min, hold down the volume up and down keys, now insert the usb cord BAM download mode) flash back to whatever rom you want.
Hey I'm not so tech sabby could you help wit steps to do the same cuz kind of have same prob. With voodoo
Technowiz said:
Hey I'm not so tech sabby could you help wit steps to do the same cuz kind of have same prob. With voodoo
Click to expand...
Click to collapse
Or you could do the same steps I have already given and it will work, you do know how to use odin right?
Sent from my SGH-T959 using XDA App
Hey guys I've been watching this forum for a while now and I need some help.
I searched around and found nothing relevant..
I got the latest kies, finally my sgs connected in kies mode, perfect. Popup for update, okay. Now... The first time i did this it showed me some progress bar which was probably something downloading. After that, the phone simply disconnected. Kies didn't show up anything, just that the phone was no longer linked to kies. The phone still showed the mtp application screen. After a few seconds kies shows 'Connecting...' and recognizes the phone again.
The second time it doesn't even get to the progress bar. When I click update, the phone simply vanishes from the kies screen.
I have not applied any lagfixes or anything, haven't rooted my phone.. Actually a few days ago I made a hard reset and everything is smooth. I just want that froyo already, I'm still running eclair.
Please, if you have a solution post it here, or at least point me in the right direction. I'm pretty much a noob when it comes to phones so.. Any help will be appreciated.
I dont know what to say
U already hard reset the phone.
Check with sgs tools what firmware do you have.
In case you have major issues.
Check the three button combo.
Uninstall kies, hard reset and try again.
Maybe is a usb problem .
How is the mount sd working ?
Sent from my GT-I9000 using XDA App
I had a problem just like this and it turned out to be a faulty USB connection. Try a different lead and USB port on the PC first.
Thanks for your replies guys, but unfortunately I still have a problem.
Reinstalled kies, nothing. Hard reset the phone again. Nothing.
Three button combo working perfectly.
In settings, the firmware seems to be 2.1-update1.
Usb problem, I don't think so. The SD card mode works flawlessly. There's one more thing I noticed. When I plug my phone in kies mode, windows also recognizes the phone, showing it up in my computer. The point is that when kies loses link to the phone, windows still finds the phone to be there, e.g. phone disconnects from kies, but not from windows. That's pretty weird..
You guys have any other suggestions..? What is the risk of flashing my phone manually to 2.2? I wanted to avoid that at all cost.
Kies also does not like the phone to be plugged in via any hub. It is best always to plug direct into a system board USB outlet.
Oh forgot to mention. I was indeed plugging the usb cable into a hub, and tried plugging in directly from the motherboard connectors and still no luck.. No idea what to do next.
Might be worth putting the phone into recovery and going to Tools, Emergency firmware recovery.
Well in the 3-button thingy i only have 'reboot system now', 'apply sdcard:update.zip', 'wipe data/factory reset' and 'wipe cache partition'. Halp plox?
Looks like you are left with two routes .
one take phone to service centre
two flash the phone to upgrade .
If flashing i would go the rom kitchen route .
That is only requiring a USB mass storage mode connection to transfer update file to sd card .
jje
I would try it. What are the risks and what happens if something goes wrong? I read somewhere that if I the 3-button combo is working I have nothing to worry about since I can reflash my phone at any given time. Is that true?
To get into recovery it is Home button. DOWN volume and Power on.
You will see a yellow triangle with "DOWNLOADING" Do not turn off the target. When you have this and have opened Kies just plug the USB in and use the recovery option if you can. As with all flashing there is always a risk so do this if you are prepared to accept this.
I've been doing a bit of research and as I saw around the only way you can mess up your flash is simply by disconnecting the cable when you shouldn't. I never actually saw anyone on different forums that have failed flashing so.. That thing pretty much gave me some courage, like hell..
I found a guide which I think would work:
http://samsunggalaxysforums.com/showthread.php/2921-How-to-use-Odin-to-upgrade-to-Froyo-from-Eclair
Do you think this is okay? Also the guy sais we should check *#1234# for PDA, and mine seems to be I9000XWJFB. He said we 'should be on JM1, JM2, JG1, JF1 etc...'. I assume that my phone falls into that category?
If this guide is erroneous please point me in the right direction, if you could.
Hello, I so hope someone can help. I just updated my galaxy tab 2 7 p113 to Android 4.0.4 UEBLH2. That was done automatically from samsung. I wanted to then install the newest update to 4.1.1 jellybean. So I downloaded it from this link. http://www.trickytweaks.com/update-...ecli4-4-1-1-jelly-bean-ota-test-firmware.html. I put the official Android 4.1.1 UEBLH2 Firmware on my sdcard then held down my power and up volume and installed it. HOWEVER, it never finished installing. Went all the way to the end. Now I HAVE NO USB CONNECTION and NO BOOT UP. Just black Since I dont have usb connection I cant us oden. CAN ANYBODY PLEASE HELP? I still can put files on my micro disk card and then put sd disk in my tab and use the power button up arrow to install something but I tried installing clockwork mod but that did not work. Iam out of ideas. P.S. My tab IS NOT ROOTED. I tried updating back to and original rom 4.04 I download but that did work. Thank you.
I think you need to enter the download mode volume down+power or recovery mode volume up+power to be able to restore the tab
Try multiple times close the tab even with long pressing power then try the button combinations (press both for multiple seconds) and release to see if you could enter any mode
If you reached download mode try flashing stock firmware for your tab specific model 3113 or 3110 or 3100 via odin (install kies and reboot before)
If you reached recovery (stock) then connect with kies and choose recover firmware from kies options (near the word file in top) you should have active internet connection
You could try charging tab even for some hours before trying button cobinations
If not try to return as not rooted so warranty is goood
Sent from Galaxy S2 or Galaxy Tab2
Mohamedselim said:
I think you need to enter the download mode volume down+power or recovery mode volume up+power to be able to restore the tab
Try multiple times close the tab even with long pressing power then try the button combinations (press both for multiple seconds) and release to see if you could enter any mode
If you reached download mode try flashing stock firmware for your tab specific model 3113 or 3110 or 3100 via odin (install kies and reboot before)
If you reached recovery (stock) then connect with kies and choose recover firmware from kies options (near the word file in top) you should have active internet connection
You could try charging tab even for some hours before trying button cobinations
If not try to return as not rooted so warranty is goood
Sent from Galaxy S2 or Galaxy Tab2
Click to expand...
Click to collapse
Yup, this should get you going again. If you can get into download mode, you should be okay. That's what Odin needs.
Download mode is volume down plus power. Then volume up
Recovery mode is volume up plus power.
I want to thank both the posters on trying to help me. I did hold down the power and download button and it went in to the download mode. HOWEVER, since I can not access usb it did not do anything. Just kept saying downloading. As I mentioned in my first post I CAN ACCESS MY SD DISK FILES by doing the power up button thing. Thats the only way I can get files on. But the DOWNLOADING down arrow just does not do anything. hmmmmmmm will keep plugging away.
I can not understand how you can not access usb, is it a lacking driver so download kies and reboot and try connect again ,also try a different usb ports (esp the rear of case) of your computer
Was usb working before the problem?
do you have cwm or stock recovery?
If cwm so download cm10 or cm9 from www.teamhacksung.org and put in usb card and flash but do a cash delete and dalvik delete afterwards not for boot loop
If stock so try stock firmware from www.samfirmware.com (register their first) and put in sd card and try to flash
Sent from Galaxy S2 or Galaxy Tab2
growthweb said:
I want to thank both the posters on trying to help me. I did hold down the power and download button and it went in to the download mode. HOWEVER, since I can not access usb it did not do anything. Just kept saying downloading. As I mentioned in my first post I CAN ACCESS MY SD DISK FILES by doing the power up button thing. Thats the only way I can get files on. But the DOWNLOADING down arrow just does not do anything. hmmmmmmm will keep plugging away.
Click to expand...
Click to collapse
I think you're misunderstanding download mode. When you get the device in download mode, connect it then to the computer, with Odin open. The only reason Odin wouldn't recognize it would be a driver issue. In that case, do as the previous poster stated. When you're in download mode, you're strictly flashing through Odin. You aren't going to see the device as a storage device on the computer. The only way your computer can interact with it at this point is Odin. Via Odin, flash the proper p3113 firmware file from sammobile/samfirmware (will be a large 600mb+ file). Once that's done, you should then be back to completely stock and healthy recovery and ROM. Reboot tab and see what happens. If it boots, and you still want to update, then make sure you get the correct ota for the base file you just flashed (that is, if you're trying to upgrade to say Jellybean). If you need more help always ask, but you should be fine. If I lived nearby I'd do it for you.
All I can say is unbelievable help here! Thank you. I am spending hours on this (plus a fortune on this new Tab 2 7). After studying up I do now understand how Odin works and how grabbing the correct firmware will do the job. HOWEVER (maybe others come across this huge roadblock) nothing can be done with out usb interaction. I DID DOWNLOAD KIES and installed it. But no matter what I do can not get any storage device listed or anything going on between tab and computer. Only thing my Tab does is when I plug it in to the computer via usb is go in to charging mode with the charging icon showing. Loading Odin does not show any connection. I have tried different computer USB plugins, 3 different computers (all I have loaded Kies on). Iam sooooooo close. If only while in the POWER BUTTON DOWN ARROW DOWNLOAD MODE and running ODIN on my computer there would be a connection I would be home free and able to flash firmware.
dictionary said:
I think you're misunderstanding download mode. When you get the device in download mode, connect it then to the computer, with Odin open. The only reason Odin wouldn't recognize it would be a driver issue. In that case, do as the previous poster stated. When you're in download mode, you're strictly flashing through Odin. You aren't going to see the device as a storage device on the computer. The only way your computer can interact with it at this point is Odin. Via Odin, flash the proper p3113 firmware file from sammobile/samfirmware (will be a large 600mb+ file). Once that's done, you should then be back to completely stock and healthy recovery and ROM. Reboot tab and see what happens. If it boots, and you still want to update, then make sure you get the correct ota for the base file you just flashed (that is, if you're trying to upgrade to say Jellybean). If you need more help always ask, but you should be fine. If I lived nearby I'd do it for you.
Click to expand...
Click to collapse
growthweb said:
All I can say is unbelievable help here! Thank you. I am spending hours on this (plus a fortune on this new Tab 2 7). After studying up I do now understand how Odin works and how grabbing the correct firmware will do the job. HOWEVER (maybe others come across this huge roadblock) nothing can be done with out usb interaction. I DID DOWNLOAD KIES and installed it. But no matter what I do can not get any storage device listed or anything going on between tab and computer. Only thing my Tab does is when I plug it in to the computer via usb is go in to charging mode with the charging icon showing. Loading Odin does not show any connection. I have tried different computer USB plugins, 3 different computers (all I have loaded Kies on). Iam sooooooo close. If only while in the POWER BUTTON DOWN ARROW DOWNLOAD MODE and running ODIN on my computer there would be a connection I would be home free and able to flash firmware.
Click to expand...
Click to collapse
How about you just gtalk me, lol. I'll probably reply faster there anyway. deliberation at gmail dot com.
Don't use kies. Install the Samsung driver for mobile phones (Google it).
Sent from my GT-P5113 using Tapatalk 2
Download Mode
growthweb said:
All I can say is unbelievable help here! Thank you. I am spending hours on this (plus a fortune on this new Tab 2 7). After studying up I do now understand how Odin works and how grabbing the correct firmware will do the job. HOWEVER (maybe others come across this huge roadblock) nothing can be done with out usb interaction. I DID DOWNLOAD KIES and installed it. But no matter what I do can not get any storage device listed or anything going on between tab and computer. Only thing my Tab does is when I plug it in to the computer via usb is go in to charging mode with the charging icon showing. Loading Odin does not show any connection. I have tried different computer USB plugins, 3 different computers (all I have loaded Kies on). Iam sooooooo close. If only while in the POWER BUTTON DOWN ARROW DOWNLOAD MODE and running ODIN on my computer there would be a connection I would be home free and able to flash firmware.
Click to expand...
Click to collapse
Once you are in download mode, connect your tab to the computer with the usb connection.....you should see a com xx number pop up in Odin in yellow reporting your device is connected thru a communication port. From there you will be able to choose the file you want as a PDA uncheck everything else...reboot...reset timer....whatever. Just make sure you have the correct firmware. There is a Odin flashback to Stock rom in the development section. Make sure it's for your device. Once you start Odin, should take about 4 mins...disconnect and hold the power button down to reboot. That's it....
Hello Everyone Again, I just want to say thank you for all of you who took the time to help. I hopefully will become knowledgeable enough to help people in the forums as I gain knowledge. I finally did find the solution. I did everything that was mentioned. And no matter what what I did with KIES drivers Samsung usb drivers, etc could not get a connection so I could us Odin to keep me back to the orgiginal 800 mb 4.04 original file. My solution was (as mentioned) I deleted all my windows drivers dealing with usb, kies, etc. Then rebooted. I notice even though I did not have a direct usb connection showing up now Odin was showing a connection! So using Odin I got to restore everything and now back to like new. Lesson learned. Hope this helps others that almost fatally brick their tablets. Thanks again for all our help
growthweb said:
Hello Everyone Again, I just want to say thank you for all of you who took the time to help. I hopefully will become knowledgeable enough to help people in the forums as I gain knowledge. I finally did find the solution. I did everything that was mentioned. And no matter what what I did with KIES drivers Samsung usb drivers, etc could not get a connection so I could us Odin to keep me back to the orgiginal 800 mb 4.04 original file. My solution was (as mentioned) I deleted all my windows drivers dealing with usb, kies, etc. Then rebooted. I notice even though I did not have a direct usb connection showing up now Odin was showing a connection! So using Odin I got to restore everything and now back to like new. Lesson learned. Hope this helps others that almost fatally brick their tablets. Thanks again for all our help
Click to expand...
Click to collapse
Glad you got it sorted.
i jus did the same thing u did
hi how r u doing. i jus did the same mistake u did and i really need your help please
Maxwell255 said:
hi how r u doing. i jus did the same mistake u did and i really need your help please
Click to expand...
Click to collapse
Hi.if u have done the exact same thing then just read the previous page and comments.
Sent from my GT-P3110 using xda app-developers app
Glad to see you resolved your issue. In the future, question/help threads belong in Q&A only.
Thank You.
Because your issue has been resolved...
Thread Closed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"If you choose not to decide, you still have made a choice"
Sent from my Galaxy Note (i717), using XDA Premium.
PeartFan40 said:
Glad to see you resolved your issue. In the future, question/help threads belong in Q&A only.
Thank You.
Because your issue has been resolved...
Thread Closed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"If you choose not to decide, you still have made a choice"
Sent from my Galaxy Note (i717), using XDA Premium.
Click to expand...
Click to collapse
Thread is still actually open, lol
Is there any way to save my tablet if there is NO firmware out?
Im talking about the SCH I705, I followed the root guide, and it got ****ed up.
Unable to boot into recovery (it goes to Odin "could not do normal boot.")
Tablet seems unresponsive sometimes (to power on/off)
Will boot cycle occasionally
???????????????????
igotbricked said:
Is there any way to save my tablet if there is NO firmware out?
Im talking about the SCH I705, I followed the root guide, and it got ****ed up.
Unable to boot into recovery (it goes to Odin "could not do normal boot.")
Tablet seems unresponsive sometimes (to power on/off)
Will boot cycle occasionally
???????????????????
Click to expand...
Click to collapse
You have to reflash your tablet using ODIN. It's not that hard. Just follow the second method here (you don't need to download android SDK)
copy this in your navigator bar : rootzwiki . com/topic/37272-verizonsch-i705-root-for-all-current-firmware/ ( delete space around the dot)
Plus, your tab will be rooted.
You're welcome.
P.S : This limitation of URL is annoying as hell.
Im sure you all have heard this one before. But I think mine may be alittle different. Im getting the error, System software not authorized etc. I bought it off of someone. I have odin 3.07 and it doesnt show the COM ports. I got USB drivers for samsung cellphones. I also got the stock ROM downloaded. I guess the question is, is there a way to flash this back to stock from the SD Card? I noticed this. I unplug the USB cable. The phone turns off. It does not come on unless the USB cable is hooked up. So I dont know if this means anything different. This phone has never been hooked up to this computer. It shows a Unknown Device in my device manager. Its hardware ID tag is USB\UNKNOWN. It is showing the SECURE FAIL: KERNAL. Can someone point me in the corrrect direction. Any help would be greatly appreciated.
VaRMiT said:
Im sure you all have heard this one before. But I think mine may be alittle different. Im getting the error, System software not authorized etc. I bought it off of someone. I have odin 3.07 and it doesnt show the COM ports. I got USB drivers for samsung cellphones. I also got the stock ROM downloaded. I guess the question is, is there a way to flash this back to stock from the SD Card? I noticed this. I unplug the USB cable. The phone turns off. It does not come on unless the USB cable is hooked up. So I dont know if this means anything different. This phone has never been hooked up to this computer. It shows a Unknown Device in my device manager. Its hardware ID tag is USB\UNKNOWN. It is showing the SECURE FAIL: KERNAL. Can someone point me in the corrrect direction. Any help would be greatly appreciated.
Click to expand...
Click to collapse
I'm guessing you when you bought it the phone booted is this correct?
If yes, what firmware is on it?
What have you done that no longer allows the phone the boot (did you flash something with Odin)?
The more info the better....
rayburne said:
I'm guessing you when you bought it the phone booted is this correct?
If yes, what firmware is on it?
What have you done that no longer allows the phone the boot (did you flash something with Odin)?
The more info the better....
Click to expand...
Click to collapse
Ive done nothing. I can get it to the POWER, VOL DOWN, HOME BUTTON and it shows the droid Downloading .....
I have no clue what firmware is on it.
VaRMiT said:
Ive done nothing. I can get it to the POWER, VOL DOWN, HOME BUTTON and it shows the droid Downloading .....
I have no clue what firmware is on it.
Click to expand...
Click to collapse
So you bought the phone and it has never booted for you?
If you have MF3 bootloader on there and someone tried to install a custom recovery it could be soft bricked.
Not sure what to suggest if you don't know what occurred to cause the phone to only go into download mode?
You could take it to best buy with a samsung experience center and have them reflash it?
The only problem with this is if you don't have MF3 bootloader, best buy will flash it and upgrade it.....
Try to Odin MDL on it first
Sent from my SGH-I337 using Tapatalk
rushi.1986 said:
Try to Odin MDL on it first
Sent from my SGH-I337 using Tapatalk
Click to expand...
Click to collapse
When you mean MDL. thats the stock rom correct? I do have that. When I look at Odin, it doesnt show anything on the COM part at the top left. Like its hooked up to a com port.
What I meant by the Downloading ...... (with the driod logo guy) Im saying I can get it to do that. Im at the point where I cant get the S4 to be reconized by ODIN. I have the stock rom, odin 3.07 files. I have tried to install the samsung usb drivers....
Still no reply on how to fix this? I have no clue on what to do here. I dont know what firmware etc is on it. I bought it this way. I just want to flash it back to factory, its the att version. It only stays on when the usb is hooked up. I can get it to go into download mode. But on the computer, it doesnt show a usb device being found. I can start odin up, but nothing appears on the COM to show what com port is available. Is there anything I can do here off of a SDCard? I also need to mention that I can not hold down vol up and power and home button to get it to go into recovery mode. It flashes it fast and goes to the yellow triangle.
Anyone please.....
You need to get Odin to recognize it. Try different usb cables. Use the usb ports on the back of the computer. Try a different computer. Without knowing the firmware you're on odin may not work, but it should still recognize your device. If you're on mdl firmware Odin will work. If you're on mf3 then you're sol.
Have you tried to get into the recovery and not just the download mode?
Volume up + Home + Power - If you can get into a recovery try to do a factory reset.
If you cant get into the recovery than you'll need Odin. Sometimes (rarely) kies well affect Odin. If you have kies uninstall it and than run odin.
- Open Odin without your phone connected.
- Power on your device, go into download (Odin) mode. Volume down + home + power.
- Now plug device into your computer.
- Odin should read it, unless its MF3 firmwire.
If your phone is MF3, you may need a Samsung bestbuy rep to reflash the mf3 firmwire.
Sent from my SGH-I337 using XDA Premium 4 mobile app
Br4nd3n said:
Have you tried to get into the recovery and not just the download mode?
Volume up + Home + Power - If you can get into a recovery try to do a factory reset.
If you cant get into the recovery than you'll need Odin. Sometimes (rarely) kies well affect Odin. If you have kies uninstall it and than run odin.
- Open Odin without your phone connected.
- Power on your device, go into download (Odin) mode. Volume down + home + power.
- Now plug device into your computer.
- Odin should read it, unless its MF3 firmwire.
If your phone is MF3, you may need a Samsung bestbuy rep to reflash the mf3 firmwire.
Sent from my SGH-I337 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have tried the power, vol up and home. It flashes the recovery, then goes back to the triangle. Odin, doesnt show a COM port that the phone is connected when i have it in download mode.
Also....i do appreciate you all for helping me figure this out.
Hello,
I was trying to flash Twrp recovery in my phone using flashify. It said flash successfully and i rebooted. It starting bootlooping. I manually tried by pressing Volume up + Home+Power keys it was still doing bootloop. I tried to goto download mode by pressing Volume Down+ Home+Power keys it still kept bootlooping even USB jig didn't work. I need your valued suggestion about what to do next.
Thanks in Advance.
I have Samsung Galaxy Grand Primr G530H
here is video link youtu.be/B_EtRTH93YE
Just flash your firmware from Odin using a PC, I had a similar problem in my tablet, it didn't had download mode either and that worked, try it.
When I connect it to Pc it keeps bootlooping and pc gives sound of connecting then disconnecting of hardware.
GorJessSpazzer said:
Just flash your firmware from Odin using a PC, I had a similar problem in my tablet, it didn't had download mode either and that worked, try it.
Click to expand...
Click to collapse
How did you flash a firmware, when your tablet didn't have download mode? What ODIN version did you use? please tell us we need your experience.
talvigi said:
How did you flash a firmware, when your tablet didn't have download mode? What ODIN version did you use? please tell us we need your experience.
Click to expand...
Click to collapse
Turn off your device, keep your finger in the button until the device is off or pull off the battery, connect it to the PC and flash your firmware through Odin, at that moment I used the 3.70 i think but you can use the latest version it's fine, that should install download mode and the whole firmware if that doesn't work I'm afraid I don't know how else I can help, that's what I did and it worked
GorJessSpazzer said:
Turn off your device, keep your finger in the button until the device is off or pull off the battery, connect it to the PC and flash your firmware through Odin, at that moment I used the 3.70 i think but you can use the latest version it's fine, that should install download mode and the whole firmware if that doesn't work I'm afraid I don't know how else I can help, that's what I did and it worked
Click to expand...
Click to collapse
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead bur or wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me food the step by step procedure it was just like this:
1. I started the Odin 3.07 and connected my device to see is it was detected or not, my surprise the Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down button pressed to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. From that moment I knew my device was not dead now so i had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
talvigi said:
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead bur or wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me food the step by step procedure it was just like this:
1. I started the Odin 3.07 and connected my device to see is it was detected or not, my surprise the Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down button pressed to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. From that moment I knew my device was not dead now so i had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
I'm glad I helped you and thanks for your description, other people with the same problem can see it, my English its not good and I was afraid that I didn't help you correctly.
Same problem, but apparently worst!
AwkWeirdo said:
Hello,
I was trying to flash Twrp recovery in my phone using flashify. It said flash successfully and i rebooted. It starting bootlooping. I manually tried by pressing Volume up + Home+Power keys it was still doing bootloop. I tried to goto download mode by pressing Volume Down+ Home+Power keys it still kept bootlooping even USB jig didn't work. I need your valued suggestion about what to do next.
Thanks in Advance.
I have Samsung Galaxy Grand Primr G530H
here is video link youtu.be/B_EtRTH93YE
Click to expand...
Click to collapse
Hello guys! Could you please help me with the same issue? The difference is that Odin doesn't recognize when I plug in my phone! I don't know what else to do. It's a G530H.
Thank you very much!
GorJessSpazzer said:
I'm glad I helped you and thanks for your description, other people with the same problem can see it, my English its not good and I was afraid that I didn't help you correctly.
Click to expand...
Click to collapse
talvigi said:
You are right I did it the same way and it worked for me too. I actually was thinking the phone was quite dead but it wasn't, I just flashed the recovery firmware 4.4.4 Russian and if you ask me for the step by step procedure it was someting like this:
1. I started the Odin 3.07 and connected my device to see if it was detected or not, to my surprise, Odin catch it, and shown added and the port number was 18.
2. I just pulled out the USB cable from my laptop and loaded the BL file only to just flash the bootloader file and see what would happen, I was trying it bcz I was totally disappointed with the device i.e. Grand Prime 530H Duos. I also noticed that my device was not stable even with that black screen it used to restart after almost five minutes in that case. And I knew that in 5 minute I will just be able to flash BL file. The BL file was loaded on the Odin now and I inserted the USB cable again while keeping the vol down + home key pressed, to my laptop when the Odin again found and connected with my device, I didnot take any more time to flash BL file.
3. As soon as i had not flashed all the SW therefore, my device didn't boot properly, and I thought it didn't work but when my device was connected to the computer I just listened the startup tone of the Android 4.4.4. or the device. From that moment I knew my device was not dead now so i pullup the battery, put it again inside to check its status, did this almost thrice, but still the same black screen, yet i heard the startup sound everytime. Now as far as knew the phone is on but showing nothing, I had to select all four files from the recovery firmware of 4.4.4 and connect the device to odin even there was no sign of download mode, as soon i clicked the Start button i saw many things in the Odin bar which were good enough to see. after the firmware flashed the device got started.
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Sent from my SAMSUNG-SM-G920A using Tapatalk
lucas13garcia said:
Hello guys! Could you please help me with the same issue? The difference is that Odin doesn't recognize when I plug in my phone! I don't know what else to do. It's a G530H.
Thank you very much!
Click to expand...
Click to collapse
Is your USB cable original is it working on other devices? And are you using a USB 2.0 port, that is very much necessary, for Odin and some other hardware/software environment applications. And you also must have Samsung USB drivers installed in your PC, you can also try all this process on some other PCs
Sent from my SAMSUNG-SM-G920A using Tapatalk
talvigi said:
Is your USB cable original is it working on other devices? And are you using a USB 2.0 port, that is very much necessary, for Odin and some other hardware/software environment applications. And you also must have Samsung USB drivers installed in your PC, you can also try all this process on some other PCs
Sent from my SAMSUNG-SM-G920A using Tapatalk
Click to expand...
Click to collapse
Hello!
Yes, that USB works with other phones. And even not being the original one, it was working to transfer files before this issue...
It is a USB 2.0 port, and even when I go to "Device Manage" on Windows, it doesn't show any port with an unknown device or something like that...
Thanks!