[Q] Sprint GS4 doesnt flash any roms - Sprint Samsung Galaxy S 4 Q&A, Help & Troubleshoot

I have a rooted Sprint GS4. It's been running CM 10.1 for last few months and everything was fine. Yesterday I attempted to flash a stock rom back onto the device so I could move it onto one of my other lines, but the phone just turns off after the initial "galaxy" screen.
I've tried 2 different roms now with the same result. I do a wipe, clear the cache, and dalvik...all the standard stuff, before flashing. Been rooting my phones for a few years now, but it's the first time i've seen this and I'm definitely not an expert. Any suggestions would be great!

Odin to a stock Rom
Root
Install recovery (goo manger for twrp is easiest)
Reboot into recovery
Install rom
Sent from my SPH-L720 using XDA Premium 4 mobile app

rarodrig6 said:
I have a rooted Sprint GS4. It's been running CM 10.1 for last few months and everything was fine. Yesterday I attempted to flash a stock rom back onto the device so I could move it onto one of my other lines, but the phone just turns off after the initial "galaxy" screen.
I've tried 2 different roms now with the same result. I do a wipe, clear the cache, and dalvik...all the standard stuff, before flashing. Been rooting my phones for a few years now, but it's the first time i've seen this and I'm definitely not an expert. Any suggestions would be great!
Click to expand...
Click to collapse
Same thing happened to me just redownload the stock ROM wipe system, cache, dalvick cache, and data then flash the sock rom if that fails odin back to stock.
Sent from my SPH-L720 using XDA Premium 4 mobile app

Thanks everyone. Yeah I had to flash it back to stock using Odin. It's not rooted any more but i'll worry about that when my girlfriend stops using it, stock is fine for her.

rarodrig6 said:
Thanks everyone. Yeah I had to flash it back to stock using Odin. It's not rooted any more but i'll worry about that when my girlfriend stops using it, stock is fine for her.
Click to expand...
Click to collapse
I had to do the same, and I've read about others as well after flashing CM.

Related

did something dumb. help?

I had encounter ICS, which was great, but isn't ready to be a daily rom, so I use koush's app to reboot into recovery.
then I got stuck at the boot animation, so I decided to open up the stock recovery, and wiped data/factory reset like an idiot. So now all i have is stuck at the M logo, or stock recovery.
Am I going to have to use an official update.zip to flash, then root my phone again?
You are going to have to sbf.
Sent from my DROID2 using xda premium
okay, so I sbf'd back to stock froyo (only GB sbf I can find around the net is a megaupload link, which is obviously not very helpful nowadays) and let it do an OTA update to GB.
I then root, just like i have before, using the motorola one click root program on my computer.
I get root, install koush's bootstrap, and reboot into recovery. I then try to install libertyv3 2.0, which seems to go well...
until i reboot. once i reboot my phone, I'm stuck back at the bootloader, and can't do anything except SBF all over again.
seriously, what's going on? maybe this liberty .zip is broken or something? (i had to find a mirror, because A team gummy's site seems to be down, and B the only other official mirror is megaupload)
I'm going to try another rom, probably encounter ICS because i already have it on my SD card.
this time, I actually read the instructions and tried to install Liberty with clockwork recovery instead of koush.
still. effing. happening.
I reboot after flashing the zip and I can't get past the bootloader screen.
Code:
Bootloader
D2.37
Err:A5,69,35,00,23
Battery OK
OK to Program
Connect USB
Data Cable
I'm seriously at wit's end here. I just got this phone but a couple days ago after I lost my original. it's an insurance replacement. I rooted with the moto one click root, and used koush to install encounter ICS. after not knowing about encounter's wonky way of activation the custom bootloader, I mistakenly wiped the phone with the stock bootloader. I SBf'd back to stock froyo, then OTA updated to gingerbread.
That is my entire history with this phone. what the hell could possibly be wrong with it?
Do you wipe data/cache/dalvic once before you flash and twice after? Liberty is dead use ICS.
Sent from my DROID2 ICS using xda premium
Albinoman said:
Do you wipe data/cache/dalvic once before you flash and twice after? Liberty is dead use ICS.
Sent from my DROID2 ICS using xda premium
Click to expand...
Click to collapse
I did certainly wipe before flashing, but have never not once heard of wiping twice after flashing. wouldn't that undo the flash? what's the point of that? And like I said, I would use encounter ICS, but it's nowhere near stable enough for daily use.
When you wipe after its just to make sure everything is stock. As long as you don't wipe /system the rom will still be there. Actually if you can live without a camera EncounterICS is an amazing daily driver. Also never use bootstrap unless you're on stock gb.
Sent from my DROID2 ICS using xda premium
I can live without a camera, but google music barely works, which is something I can't live without. I'm thinking about going back to Apex until encounter gets really good (had apex for months up until i lost my original phone)
Google music is working fine for me. Good idea apex is great.
Sent from my DROID2 using xda premium

[Q] Rooted, CM 10.1, clean rom, now stuck...need help!

Hey, I could really use some guidance here. I'll present the information as simply as I can:
I bought a Galaxy s4 AT&T a few days ago. I've been interested in rooting and flashing different roms, but I think I may have done a bit too much.
I rooted using the motochopper method - great, worked like a charm.
I made a backup of my original rom using CWM. I even took that backup and saved a copy of it on my Mac - perfect.
I thought I'd try Cyanogenmod 10.1, so I downloaded the latest nightly build and flashed it using CWM - so far so good.
Everything was working fine, but my LTE (or any data) was not working at all. I could use Wifi, but once I turned wifi off, I had no data, no gps, no 3g, no 4g, no LTE. I tried the *#*#4636*#*# method, the LTEOnOff app, and changing my APN based on the recommendations provided in this thread - I just couldn't get it to work.
I thought I'd try restoring my original backup, but when I went into CWM to do so, it said that my backup could not be found...(I still have a backup on my computer, just in case)
I needed my phone to work, and badly needed LTE to do so. So, I downloaded this rom: [ROM] CleanROM 1.0 -★| Clean and Smooth! | The Way Nature Intended! |★-
So far, this rom was working fine - it's just a debloated version of TouchWiz - which I like. But, here's my problem now - If my phone reboots, it stays frozen on the Samsung logo (with unlocked lock logo underneath), and I can't get past it. I'd have to go BACK into recovery, and flash the CleanROM all over again, and set my phone up as new with all data wiped.
I really need my phone to work again, and I don't know where to go from here. What options do I have left? What can I do to get out of that frozen Samsung loading screen? Can't I just reset my phone to the way it was? Can't the CM10.1 rom work with LTE?
Your help will be greatly appreciated.
Your best option is to flash the stock MDB firmware via odin . After you get the PASS on Odin go ahead and manually boot into stock recovery and wipe data factory reset again then reboot. You will have to re root and reinstall recovery but this will take care of any issues you had from a bad flash.
http://forum.xda-developers.com/showthread.php?t=2261573
Sent from my GT-I9505G using Tapatalk 2
mavverick said:
Hey, I could really use some guidance here. I'll present the information as simply as I can:
I bought a Galaxy s4 AT&T a few days ago. I've been interested in rooting and flashing different roms, but I think I may have done a bit too much.
I rooted using the motochopper method - great, worked like a charm.
I made a backup of my original rom using CWM. I even took that backup and saved a copy of it on my Mac - perfect.
I thought I'd try Cyanogenmod 10.1, so I downloaded the latest nightly build and flashed it using CWM - so far so good.
Everything was working fine, but my LTE (or any data) was not working at all. I could use Wifi, but once I turned wifi off, I had no data, no gps, no 3g, no 4g, no LTE. I tried the *#*#4636*#*# method, the LTEOnOff app, and changing my APN based on the recommendations provided in this thread - I just couldn't get it to work.
I thought I'd try restoring my original backup, but when I went into CWM to do so, it said that my backup could not be found...(I still have a backup on my computer, just in case)
I needed my phone to work, and badly needed LTE to do so. So, I downloaded this rom: [ROM] CleanROM 1.0 -★| Clean and Smooth! | The Way Nature Intended! |★-
So far, this rom was working fine - it's just a debloated version of TouchWiz - which I like. But, here's my problem now - If my phone reboots, it stays frozen on the Samsung logo (with unlocked lock logo underneath), and I can't get past it. I'd have to go BACK into recovery, and flash the CleanROM all over again, and set my phone up as new with all data wiped.
I really need my phone to work again, and I don't know where to go from here. What options do I have left? What can I do to get out of that frozen Samsung loading screen? Can't I just reset my phone to the way it was? Can't the CM10.1 rom work with LTE?
Your help will be greatly appreciated.
Click to expand...
Click to collapse
Factory Reset
Wipe Cache
Wipe Dalvik
Format /system
Flash ROM or ROM and gapps if AOSP
Reboot
KingKongDingDong said:
Factory Reset
Wipe Cache
Wipe Dalvik
Format /system
Flash ROM or ROM and gapps if AOSP
Reboot
Click to expand...
Click to collapse
Having the same issue so I figured I'd give these steps a shot. Followed them exactly and phone (AT&T S4, TWRP) would won't even reboot the first time into CleanROM. I'm stuck on the Samsung screen with the lock.
edit: I've noticed that now, when I reboot into TWRP, it prompts me for a password. Hitting cancel takes me to the regular home screen, but I had not been getting the password prompt before attempting to install CleanROM. A permissions issue, perhaps?
edit 2:
I've just spent some time trying a bunch of things with bits of good luck surrounded with tons of bad. Below are the steps I've taken to try to get CleanROM to boot (and reboot) without any issues. Hopefully they help figure out the issues we're having.
Wipe Cache
Wipe Dalvik
Wipe /system
Flash CleanROM
Reboot
---- Failed
Reboot into Recovery
Prompted for password, hit cancel
Fix permissions
---- Failed
Reboot to recovery
Prompted for password, hit cancel
Format data (type yes)
Reboot
---- Successfully booted to CleanROM
Ran through phone / account setup
Saw home screen
Powered off and then back on (not using reboot)
---- Failed
Reboot to Recovery
No longer prompted for password
Factory Reset
Attempt to Fix Permissions: failed
Restore default settings
Reboot system
---- Failed
Reboot to Recovery
Prompted for Password, hit cancel
Format Data (type yes)
Reboot System
--- Successfully booted to CleanROM
Ran through phone / account setup
Saw home screen
Reboot (using reboot, not power off / on)
---- Failed
Reboot to Recovery
Prompted for password, hit cancel
Factory Reset: failed
Restore Default settings
Prompted for password, hit cancel
Factory Reset: failed
* Internal Storage showing 0MB (as if it's not reading it correctly)
Fix Permissions
Prompted for password, hit cancel
Nothing has changed, my phone is currently chilling in TWRP
MJHawaii said:
Your best option is to flash the stock MDB firmware via odin . After you get the PASS on Odin go ahead and manually boot into stock recovery and wipe data factory reset again then reboot. You will have to re root and reinstall recovery but this will take care of any issues you had from a bad flash.
http://forum.xda-developers.com/showthread.php?t=2261573
Sent from my GT-I9505G using Tapatalk 2
Click to expand...
Click to collapse
This. You decided to ignore this post for some reason.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
cuffed zhesea
Cataligh said:
This. You decided to ignore this post for some reason.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
I can't speak for OP, but I was hoping there was another way to rectify what has already been done without flashing stock seeing as how I'm on OSX. If that's the only option, then so be it.
Hey. Thanks for the feedback in this thread. I flashed factory through Odin, and everything is working fine. I then factory reset my phone through factory recovery. I'm back to standard touchwiz with all the bloat lol.
I'm going to wait until there a more stable release of cm10.1 - that was a good rom.
Appreciate all the help people!
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Your best bet is do what "cataligh" mentioned... flash back to stock via odin...
Sent from my SAMSUNG-SGH-I337 using xda premium
When you flashed cm10 it probably wipe the internal sdcard, you should ALWAYS do you backups to the extsdcard...period.
TheAxman said:
When you flashed cm10 it probably wipe the internal sdcard, you should ALWAYS do you backups to the extsdcard...period.
Click to expand...
Click to collapse
Yeah, absolutely! I always backed up and flashed roms from my external SD.
mavverick said:
I'm going to wait until there a more stable release of cm10.1 - that was a good rom.
Click to expand...
Click to collapse
waiting is for simpletons. get aokp and transcend...
jaboles said:
I can't speak for OP, but I was hoping there was another way to rectify what has already been done without flashing stock seeing as how I'm on OSX. If that's the only option, then so be it.
Click to expand...
Click to collapse
As I mentioned before starting over is always the Best and Safe way to go. Shortcuts will only cause you headaches and possibly get you a brick that is why you see Odin stock threads. Do yourself a favor and start over I know it sucks but when your modifying your phones its gonna happen once in awhile.
Sent from my GT-I9505G using Tapatalk 2
MJHawaii said:
As I mentioned before starting over is always the Best and Safe way to go. Shortcuts will only cause you headaches and possibly get you a brick that is why you see Odin stock threads. Do yourself a favor and start over I know it sucks but when your modifying your phones its gonna happen once in awhile.
Sent from my GT-I9505G using Tapatalk 2
Click to expand...
Click to collapse
Wise words. Took your advice, installed Windows with boot camp, and got back to stock via odin.
I am going to say something about this thread, we are all giving advice on how to do this and that, and not once is it mentioned anywhere....in the OP
WHAT DEVICE WE ARE TALKING ABOUT! PLEASE STATE THE DEVICE WHEN NEEDING HELP!
The Ax says, I apologize if I missed what device.
TheAxman said:
I am going to say something about this thread, we are all giving advice on how to do this and that, and not once is it mentioned anywhere....in the OP
WHAT DEVICE WE ARE TALKING ABOUT! PLEASE STATE THE DEVICE WHEN NEEDING HELP!
The Ax says, I apologize if I missed what device.
Click to expand...
Click to collapse
My original question was for the AT&T version of the Galaxy S4 - i337.
xBeerdroiDx said:
waiting is for simpletons. get aokp and transcend...
Click to expand...
Click to collapse
Welllllll I just tried installing AOKP as well (Task650). Buttttttt, same issue with the LTE stuff. I tried reviewing all the APN settings, but didnt get any data connection on my phone except for wifi.
mavverick said:
Welllllll I just tried installing AOKP as well (Task650). Buttttttt, same issue with the LTE stuff. I tried reviewing all the APN settings, but didnt get any data connection on my phone except for wifi.
Click to expand...
Click to collapse
What APN settings were you using?
Sent from my SAMSUNG-SGH-I337 using xda premium
doktor buknasty said:
What APN settings were you using?
Sent from my SAMSUNG-SGH-I337 using xda premium
Click to expand...
Click to collapse
Yeah, data was enabled - and I was using ATT LTE apn settings that I found on these forums. I made sure to use the right now. Plus, when I rebooted my phone, it got stuck on the Samsung lock screen again...
Juuuuust ODINed back to factory right now for the second time :crying:
Was it these settings:
Sent from my SAMSUNG-SGH-I337 using xda premium
doktor buknasty said:
Was it these settings:
Sent from my SAMSUNG-SGH-I337 using xda premium
Click to expand...
Click to collapse
Yes, those were the exact settings that I used. Is it possible that I could have a defective phone or sim card?
Right now, I am on factory touchwiz with root enabled, and my phone is working perfectly fine. I can reboot, use LTE, everything. The problem starts when I load any CM or AOKP rom...

I need help

Hello!
I had my S4 rooted and nandroid back up. I was trying to install this link:
http://forum.xda-developers.com/showthread.php?t=2316308
I installed it and gapp installed too and rebooted. I got this message appears
"System software not authorized by AT&T has been found on your phone"
upper corner in orange says "kernel Failed"
That means I did something wrong?
I read about odin. Does Stock rom get you back to fully stock?
Thanks
Did you run loki doki? see.your on at&t..locked bootloader and i dont think that rom is autolokied. Boot back into recovery flash ld.and see if it boots.
Yes odin will put your phone back to.stock,been there done that lol.
sent from my CleanRom 1.5 i337m
force70 said:
Did you run loki doki? see.your on at&t..locked bootloader and i dont think that rom is autolokied. Boot back into recovery flash ld.and see if it boots.
Yes odin will put your phone back to.stock,been there done that lol.
sent from my CleanRom 1.5 i337m
Click to expand...
Click to collapse
Ok, I been reading some threads about recovery, I didn't relieze, i was away from s3 so long. I just restored from backup data and it boots into this stuck Samsung screen with custom unlocked logo. Bootloop?
Havent seen that particular screen but yeah sounds like your bootlooped. If.you can three finger back into recovery and have a nandroid i would full wipe then Restore your back up (even though people.say restoring wipes anyway..id wipe.if u.are using twrp do not format data!).if.your still looped you may have to try and odin back to stock.firmware can be found on sammobile.com had to do this the other night due to a bad nandroid..lots of fun lol.
sent from my CleanRom 1.5 i337m
force70 said:
Havent seen that particular screen but yeah sounds like your bootlooped. If.you can three finger back into recovery and have a nandroid i would full wipe then Restore your back up (even though people.say restoring wipes anyway..id wipe.if u.are using twrp do not format data!).if.your still looped you may have to try and odin back to stock.firmware can be found on sammobile.com had to do this the other night due to a bad nandroid..lots of fun lol.
sent from my CleanRom 1.5 i337m
Click to expand...
Click to collapse
Thank you!:victory:
My heart dropped like fainting ghost after I see the at&t software showed up. I wiped factory reset and goes past the samsung with unlocked logo into at&t boot up like new phone. It took 5 mins to get into welcome screen. All is working.
Now, I begun to wondering why my logo says it bootloader unlocked and I download correct at&t rom is in? I use this causal download from this link:
http://forum.xda-developers.com/showthread.php?t=2297900
I am trying to understand and pick my first rom. Was thinking downloading pure google rom. Had to read again
That mod.will loki your kernel,prolly why it says unlocked. I.have the.canadian. version..unlocked already thank.god lol.
A.simple wipe can work wonders..if you can get into.recovery and have something.to.flash most times your gona be okay.
Glad your back in.business!
sent from my CleanRom 1.5 i337m
Flash another kernel made for your device, or go thru the ODIN thing, your choice. this is for anyone who have that triangle.
Yes, I read some thread and the roms need kernel, without kernel installed which was has leaded me into that warning att screen. I tried again with roms above link with ktoon kernel and made it through. I was probably be dumb. Pardon me, lots to relearn here.
I own iPhone 4s but I went back to android.
Sent from my SM-T310 using xda app-developers app
You should be able to get rid of that boot screen with the lock on it by using triangle away. http://forum.xda-developers.com/showthread.php?t=1494114
Does anyone know what that com2s and the one below it is? And anyway to delete them?
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
[email protected] said:
Does anyone know what that com2s and the one below it is? And anyway to delete them?
Sent from my SAMSUNG-SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
delete em (un-install), junk, are you getting spam and such? Did you install those? Do you have any protection on your device? Just curious.
Thank you
TheAxman said:
delete em (un-install), junk, are you getting spam and such? Did you install those? Do you have any protection on your device? Just curious.
Thank you
Click to expand...
Click to collapse
I can't find them to uninstall them just to force stop and unable them. Not getting any spam but I have used 4shared and and downloaded some stuff that didn't work and just download to my storage. No protection for my device. Any suggestions? I haven't had an android since the mytouch on T-Mobile years ago and I'm still new to this.
Sent from my SAMSUNG-SGH-I337 using xda app-developers app

[Q] jflteatt not liking any kitkat roms

Hi, I was hoping to get some help and insight with the situation I've been dealing with. I'll give as much information as possible so that someone might be able to point me in the right direction.
I have an att galaxy s4 that was purchased and rooted before the mf3 ota that made everything so difficult. I've flashed several roms and decided to go with liquidsmooth 2.37 atm and I'm experiencing a few odd issues (stock mss not working) that no one else seems to have, but for the most part it's running very well. Lately I've wanted to go with a rom using the new 4.4 and I've tried a handful no matter what rom I try I have the same issues. so far I've tried CM 11, Omnirom and Gummy. With all of them everything runs very laggy and glitchy and will frequently freeze until it crashes and reboots. Every single time I've used whatever gapps are linked in the op for every rom and followed flashing instructions to the letter (wipe data/factory reset, wipe cache, wipe dalvik, flash rom , flash gapps, flash super su (if needed) and reboot) and I've even tried different recoveries (both cwm recovery 6.0.4.4 and the latest philz cwm recovery) same results every time. This part shouldn't matter, but I tried flashing these roms while on the original mdl modem and after upgrading to mj9. Let me know any other info you need, but I've tried to be thorough. I appreciate the help.
So what firmware are you on right now?
scott14719 said:
So what firmware are you on right now?
Click to expand...
Click to collapse
I'm guessing mdb
sorry thought i mentioned the firmware is mdl
Rockman195 said:
sorry thought i mentioned the firmware is mdl
Click to expand...
Click to collapse
Looks like you're doing everything right. Have you checked md5's of your downloads?
I don't know how to do that or else I would
Sent from my SGH-I337 using xda app-developers app
Rockman195 said:
I don't know how to do that or else I would
Sent from my SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
http://onlinemd5.com/
Thanks for the link. I'm looking into md5 checking and I downloaded the hash droid app. My only question is when I calculate the md5 of a file what am I supposed to compare it to?
Sent from my SGH-I337 using xda app-developers app
Rockman195 said:
Thanks for the link. I'm looking into md5 checking and I downloaded the hash droid app. My only question is when I calculate the md5 of a file what am I supposed to compare it to?
Sent from my SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
You should compare it to the md5 typically posted where you download the file from
Ok so the dl site like devhost or whatever
Sent from my SGH-I337 using xda app-developers app
Rockman195 said:
Ok so the dl site like devhost or whatever
Sent from my SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
Correct. I usually just compare the last 5 or 6 characters. If they match it's very unlikely the others won't too.
tried going back and looking in all the threads that I downloaded roms from, can't find md5s for any of them with one exception and thats an outdated version of a rom I'm not currently trying to flash, so I don't see the point in downloading it just to compare the md5
Downloaded an omnirom build and checked the md5 and everything was good, plus I would be surprised if the md5s were bad on all the roms I've tried. Any other suggestions? Should I try two recovery instead of coming?
Sent from my SGH-I337 using xda app-developers app
Rockman195 said:
Downloaded an omnirom build and checked the md5 and everything was good, plus I would be surprised if the md5s were bad on all the roms I've tried. Any other suggestions? Should I try two recovery instead of coming?
Sent from my SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
I'm running out of ideas try twrp recovery. Here is a zip you can flash in your current recovery http://forum.xda-developers.com/showthread.php?p=45511518
flashed twrp and that royally screwed up the phone. opened recovery using twrp and made a back up then did a system wipe and went to install the rom and when I went to do that, the list of all teh files you have to choose from was blank. I could go through different folder levels but the part where it shows the contents was always emtpy. Sometimes I could touch the area and see I portion highlight like it was making a selection but it wouldnt do anything and there was no file name there. Went to restore the backup I made and there was nothing in the list of backups to restore from. Rebooted the phone and liquid smooth 2.37 loaded like a clean flash with none of my info, files, apps, etc so I downloaded rom manger from the playstore and put the latest cwm touch on there. When I went in recovery none of my cwm backups where there or anything so i went to reboot and it only shows the samsung boot screen. Downloaded a few different roms and gapps on my sd card from y computer and put them on the phone and flashed the roms and gapps and still can't get past the boot screen. I'm really open to suggestions on this one.
If it was me, at this point I'd Odin the stock mdl firmware and start all over again. Something's not right with your phone. But it scares me a little since things aren't flashing correctly and there could be something wrong with your internal memory. If memory is bad it could make things worse.
I think your right. Do you know where I can find the stock firmware and instructions for flashing it? I haven't used Odin in a while.
Sent from my GT-N8013 using xda app-developers app
Rockman195 said:
I think your right. Do you know where I can find the stock firmware and instructions for flashing it? I haven't used Odin in a while.
Sent from my GT-N8013 using xda app-developers app
Click to expand...
Click to collapse
You can get the stock firmware at sammobile.com. it's free but you have to register. You'll download a zip file. Use 7-zip to extract the .tar.md5 file from it and use that in Odin, PDA slot. This is a guide that is not for the s4 but the procedure is the same. It has screen shots in it that help. Don't use any files in it though other than odin. Good luck. http://forum.xda-developers.com/showthread.php?p=26056924
I haven't read the whole thread, so hopefully these haven't already been covered.
1) Make sure your recovery supports 4.4. Not all of them do. Stay the heck away from TWRP because it's done nothing but suck for Galaxy S4, while it was absolute king for the S3. The wrong recovery can still flash a ROM but that ROM may not work very well.
2) Ensure you do a COMPLETE wipe. As in wipe /system and /data. Make sure your internal SD card is formatted. 4.4 may not use some things & folders that 4.2 and 4.3 did, which might cause problems.
3) If you have an external SD, then make sure 4.4 is using the right path for it to access any important files you may have on it, like apps2sd & such.
Well since screwing things up with twrp I'm back to having a working phone again. I didn't have to use Odin but I still might just to go back to stock and then try kit kat. I went into cwm recovery and formatted the system then flashed liquidsmooth 2.37 which is what I was running. Everything works fine with that except when I use the rom manager widget to boot into recovery, it goes to the boot screen with booting recovery at the top but doesn't go further. I have to use the 3 button method to get into recovery. The other odd thing is that mms works for me now.
I tried flashing gummy 4.4 again since everything is fine in jb but I still have the same jittery twitchiness. One thing I noticed is that when I go into the performance settings in 4.4 the current cpu reading will jump from 300 mhz to 1200 to 400 to 1800 etc just at idle. Is that normal. My note 10.1 holds steady when it's just sitting there.
To answer your questions, I'm using cwm 6.0.4.4 which is kit kat approved and I formatted and wiped everything before flashing and it didn't change anything. I appreciate your help so far and look forward to more insight.
Sent from my SGH-I337 using xda app-developers app

failed flashing Resurrection-Remix-LP-v5.5.9-20151121-jfltexx.zip ROM

Hi. Today I wanted to flash my s4 I9505 device with this ROM http://forum.xda-developers.com/galaxy-s4/i9505-develop/rom-resurrection-lollipop-v5-5-5-t3195202 but at the end the problem has popped out. I had an android 5.0 lollipop don't remember which one exactly. First I've rooted my phone with odin 3.07. Then I've downloaded ROM Manager (https://play.google.com/store/apps/details?id=com.koushikdutta.rommanager) from Play and installed recovery. It looked like this: http://www.pocketpc.ch/attachments/...ry-fuer-galaxy-s4-mini-gt-i9195-wp_000062.jpg. Then I wiped cache and data. It appeared with totally clear phone. Then I installed superuser from the recovery level and then problem appeared. The phone is booting up normally but after all the starting logos it comes with black screen and multiple crashed of Multimedia, Camera, Interface and so on. Is it bricked? I don't know what to do, I have to say I am kinda newbie. Hope that someone will help.
pg_ar said:
Hi. Today I wanted to flash my s4 I9505 device with this ROM http://forum.xda-developers.com/galaxy-s4/i9505-develop/rom-resurrection-lollipop-v5-5-5-t3195202 but at the end the problem has popped out. I had an android 5.0 lollipop don't remember which one exactly. First I've rooted my phone with odin 3.07. Then I've downloaded ROM Manager (https://play.google.com/store/apps/details?id=com.koushikdutta.rommanager) from Play and installed recovery. It looked like this: http://www.pocketpc.ch/attachments/...ry-fuer-galaxy-s4-mini-gt-i9195-wp_000062.jpg. Then I wiped cache and data. It appeared with totally clear phone. Then I installed superuser from the recovery level and then problem appeared. The phone is booting up normally but after all the starting logos it comes with black screen and multiple crashed of Multimedia, Camera, Interface and so on. Is it bricked? I don't know what to do, I have to say I am kinda newbie. Hope that someone will help.
Click to expand...
Click to collapse
Flash recovery through ODIN as well. Then wipe your mobile and then flash your ROM
Sent from my GT-I9505 using Tapatalk
a602820922 said:
Flash recovery through ODIN as well. Then wipe your mobile and then flash your ROM
Sent from my GT-I9505 using Tapatalk
Click to expand...
Click to collapse
thanks man it helped me so much
I flashed on my tmobile SGS4 and only one issue, not being able to send and receive text messages... Otherwise, everything else works! Everything! Great job devs! ?
Sent from my SGH-M919 using Tapatalk
pg_ar said:
thanks man it helped me so much
Click to expand...
Click to collapse
Great you got it working.
Just a small tip for in the future. Make sure you use TWRP recovery. CWM and Philz is outdated.

Categories

Resources