I dunno what went wrong here...
1) I have GT-I9505 (SSN: -I9505GSMH). I installed Galaxy S4 toolkit
2) Reboot into download mode. Used toolkit/Odin to root phone. Boots up. See SU.
3) Reboot into download mode. Used toolkit/Odin. Flashed TWRP Recovery
4) Phone boots up normal. Reboot into TWRP recovery. Did a factory Reset. Format.
5) Installed Zip (Latest Omega 9.0 ROM), unchecked the things I didn't want to install. Completed install, no errors reported. Rebooted.
6) Phone stuck on Samsung boot screen. I left it overnight thinking sometimes it may take 15 mins to boot system after new install.
7) Woke up, battery dead. Tried to charge phone. No charging indicators when plugged in. With whatever juice I had left I booted into TWRP recovery, it starts to charge again as I see the % batter increase after 5 mins.
-=-=-=-=- Did the Following to try to repair
a) Reinstalled Omega, this time leaving alll options on. Rebooted, stuck in Samsung boot
b) Flashed Phil CWM touch recovery, did complete wipe to install new ROM. Rebooted into Phil recovery. Flashed OMEGA. Reboot, stuck in Samsung boot.
c) Rebooted into Phil recovery, installed echo ROM, rebooted. Black screen. Rebooted into Phil. This time cannot get into recovery.
d) Started panicking, used Odin flashed TWRP. Would not flash. Something displayed about PIT error. Flashed Phil again. Reboot into recovery, WORKS! (recovery only). Went back into Download mode flashed TWRP. Rebooted, also WORKS!. Did a factory wipe. During wipe there was an error. Format, factory reset, error during wipe. Flashed OMEGA. Reboot. Stuck on samsung boot loop.
e) Downloaded official Samsung kernal for i9505 thinking it was the full flash rom. Flashed with ODIN (hoping to put everything back to factory). Completed flash, phone boots. I get OMEGA ANIMATION!!! Waited for 15 mins. Stuck on Animation. Reflashed TWRP. Rebooted, installed OMEGA...again. Stuck on samsung boot screen.
-=-=-= Kinda frustrated. What did I do wrong in the beginning?
There are so many official roms for the S4 based on region. What can I do to put it back to factory again? I purchased phone in Australia @ Samsung store. I figured download the Australia ROM but there are like 5 of them 4 being network branded roms I think. THe other one XSA is unbranded?
I tried searching for help but so far nothing works.
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
arnob_xperia said:
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
Click to expand...
Click to collapse
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
kabloomz said:
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
Click to expand...
Click to collapse
first use CWM or TWRP or whatever you want and format everthing
flash a fresh firmware(latest i prefer)
then flash stock recovery via odin of the built version what v9 was used, simply reboot to recovery and it will say MULTI CSC APPLIED from fresh frimware you used
then flash TWRP/CWM and flash v9
again simply reboot to recovery and it will say MULTI CSC APPLIED from V9
it will reboot, you must need to apply CSC to boot your phone
I can confirm this!
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
douglascamata said:
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
Click to expand...
Click to collapse
thats right stock recovery boot is needed to apply CSC
problem
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
Do you have an IMEI showing on your phone? What recovery did you use to flash Omega?
It matters, because some recoveries will screw it up.
Do you try to install with Philz recovery?
Sent from my GT-I9505 using xda premium
macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
wifi problem
kabloomz said:
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
Click to expand...
Click to collapse
I did flash the Omega v9.1 and applied the wifi fix but the wifi is still broken. I tried unrooting it by flashing the original rom and formatting the data but the wifi is still broken. I can't turn it on. Thanks for the instructions anyways. ))
no pit partition
also, when i tried to root it again, it fails and says there is no PIT partition..
Where is the csc in TWRP so I can so what ones on the phone..??
What stock firmware can I use for a Orange Network in the UK.
GT-i9505 stuck on boot when upgraded from omega v16 to v21
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
BizK1d said:
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
Click to expand...
Click to collapse
Hi, I am having the same problem. First I installed the new firmware (NA5) and modem, tested it with the Omega ROM v21 and boot caught on so now tested the rom Fox Hound 4.1 and am having the same problem.
Kies tested this option but have not had the same luck as you. = /
Anyone know the reason? The rom Google Edition Jamal runs on my phone.
i9505
So i was on sacs custom 4.3 rom with the mja modem not the bootloader i manually updated to mja and i was wanting to try the 4.4 gummy rom and was having problems with data so i flashed my old 4.3 rom back on my phone and now it says i have no mobile connection but i have data. i dont get it ive tried everything that i can think of ive tried prl and profile update i also tried calling sprint but they are closed ive tried restoring my old backups and i even used ODIN to flash completely back to stock nothing has worked can some one please help im not sure what else to do
I had something similar happen to me, so what I did was completely wipe everything including my internal SD. Then I used Odin to flash MF9 MODEM but I selected not to reboot on odin then when I saw that it had passed I pulled the battery and booted into recovery and flashed SACS V8. you can flash whatever even his 4.3 with the MF9 MODEM.
Sent from my SPH-L720 using XDA Premium 4 mobile app
Yesterday I was normally on the cm11 nightlies, and decided to go back to 4.2.2 stock tmobile, just to update to kk . I loaded my stock backup, and all went fine. It downloaded an update, did not say what just system update and after that it restarted to twrp recovery. Tried rebooting to system, but all it does is boot back to twrp. What I saw is that it reverted back from 2.6.4 to 2.6.3 version. Flashed the 2.6.4 version from my folder, and the same happens. Tried restoring my backups, taking long but to no avail. Right now I have a bootloop to twrp and don't know what to do. My computer doesn't even recognize phone. Not even usb otg shows up.
Sent from my Nexus 7 using XDA Premium HD app
There are threads in this very section that will explain what you have to do. Note, never take an ota with a custom recovery!
Sent from my VS980 4G using Tapatalk
Problem solved. I downloaded 4.4.2 stock rom to my otg and mounted on my phone.then flashed from there.
Hi All,
Just wondering what's going on with my phone - it's a Galaxy Note 4 SM-N910G with Optus Australia.
Here's the situation:
I rooted my phone using Chainfire method from 5.1.1 Optus firmware.
Then, I installed TWRP, backed up all partitions (INCLUDING EFS).
After that, installed Cyanogenmod. Holy damn, I need to go back to stock...
so...
I booted back into TWRP
I reset phone as usually would to restore/install ROM.
I restored firmware backup in TWRP.
Reboot to system
-- BOOTLOOP --
happens every time i try to restore, and the only way I can use my phone right now is to reflash Cyanogenmod 12.1 nightlies onto it - which have problems (such as I cannot reboot with CM12.1 because if I do after installing it, the phone app breaks and I cannot get past anything because of toast message "com.android.phone" has stopped..., so then only way to get it to work again is to reflash CM12.1 again - this happens about twice daily...)
-- -- PLEASE HELP!
What happens to TWRP backups that mean i cannot restore my stock backup without it bootlooping? and why can devs not post a clean stock flashable ZIP copy of stock firmwares? Its great having all these mods, but how about something that doesn't require umpteen thousand bloody applications to reflash your phone with? Whatever happened to a simple ZIP? when I see ZIPs, devs see thanks buttons being pushed!
-- THANKS
MrDhark32 said:
Hi All,
Just wondering what's going on with my phone - it's a Galaxy Note 4 SM-N910G with Optus Australia.
Here's the situation:
I rooted my phone using Chainfire method from 5.1.1 Optus firmware.
Then, I installed TWRP, backed up all partitions (INCLUDING EFS).
After that, installed Cyanogenmod. Holy damn, I need to go back to stock...
so...
I booted back into TWRP
I reset phone as usually would to restore/install ROM.
I restored firmware backup in TWRP.
Reboot to system
-- BOOTLOOP --
happens every time i try to restore, and the only way I can use my phone right now is to reflash Cyanogenmod 12.1 nightlies onto it - which have problems (such as I cannot reboot with CM12.1 because if I do after installing it, the phone app breaks and I cannot get past anything because of toast message "com.android.phone" has stopped..., so then only way to get it to work again is to reflash CM12.1 again - this happens about twice daily...)
-- -- PLEASE HELP!
What happens to TWRP backups that mean i cannot restore my stock backup without it bootlooping? and why can devs not post a clean stock flashable ZIP copy of stock firmwares? Its great having all these mods, but how about something that doesn't require umpteen thousand bloody applications to reflash your phone with? Whatever happened to a simple ZIP? when I see ZIPs, devs see thanks buttons being pushed!
-- THANKS
Click to expand...
Click to collapse
This http://forum.xda-developers.com/note-4/help/n910c-to-stock-rom-cm13-t3321132 :good:
One possible solution is to flash the appropriate stock rom via odin. After booting, install twrp and root your phone. After this you can restore your previously saved stock rom via twrp.
MrDhark32 said:
Hi All,
Just wondering what's going on with my phone - it's a Galaxy Note 4 SM-N910G with Optus Australia.
Here's the situation:
I rooted my phone using Chainfire method from 5.1.1 Optus firmware.
Then, I installed TWRP, backed up all partitions (INCLUDING EFS).
After that, installed Cyanogenmod. Holy damn, I need to go back to stock...
so...
I booted back into TWRP
I reset phone as usually would to restore/install ROM.
I restored firmware backup in TWRP.
Reboot to system
-- BOOTLOOP --
happens every time i try to restore, and the only way I can use my phone right now is to reflash Cyanogenmod 12.1 nightlies onto it - which have problems (such as I cannot reboot with CM12.1 because if I do after installing it, the phone app breaks and I cannot get past anything because of toast message "com.android.phone" has stopped..., so then only way to get it to work again is to reflash CM12.1 again - this happens about twice daily...)
-- -- PLEASE HELP!
What happens to TWRP backups that mean i cannot restore my stock backup without it bootlooping? and why can devs not post a clean stock flashable ZIP copy of stock firmwares? Its great having all these mods, but how about something that doesn't require umpteen thousand bloody applications to reflash your phone with? Whatever happened to a simple ZIP? when I see ZIPs, devs see thanks buttons being pushed!
-- THANKS
Click to expand...
Click to collapse
Sorry no help from me but I have a similar problem. At some point mine quit booting to TWRP and I got a huge OTA update a few days ago and every time I try to boot into recovery it ends up in Stock Recovery only after going to little android saying installing updates(it fails & eventually goes to stock recovery.) I did a reset and still have 5.1.1 installed and still have the same behavior.
I have the professional version of the unified toolkit and it says if it is still booting into stock recovery select options 7, 3 which I did but it didn't fix the problem. I think what's getting me is it thinks there are still system updates to install.
I tried to factory reset a custom ROM, got sent to TWRP then I can't reboot to system from there. Tried a clean install but to no avail. I've looked around on the internet and I think I have to reinstall stock ROM and then reinstall custom recovery and ROM, except if I were to install the stock ROM once again (with sp tools) I need my phone to be turned off, not in recovery mode. So how exactly should I proceed now?
EDIT: Managed to get rid of the TWRP bootloop by restoring from a stock nandroid I've found on the forums, coupled with flashing a stock recovery image using TWRP. Reunlocked bootloader, flashed TWRP all over again and then flashed custom ROM and Gapps. Everything running fine now.
Mods feel free to delete this post since it's solved itself, or leave it in case anyone needed help concerning the same issue, up to you.
Hi
Bibi if you’re still active on xda reply to this
Help me i got same issue with you. Can provide me with ur stock rom and stock recovery? And how to do. Thanks very much.
Bibicp said:
I tried to factory reset a custom ROM, got sent to TWRP then I can't reboot to system from there. Tried a clean install but to no avail. I've looked around on the internet and I think I have to reinstall stock ROM and then reinstall custom recovery and ROM, except if I were to install the stock ROM once again (with sp tools) I need my phone to be turned off, not in recovery mode. So how exactly should I proceed now?
EDIT: Managed to get rid of the TWRP bootloop by restoring from a stock nandroid I've found on the forums, coupled with flashing a stock recovery image using TWRP. Reunlocked bootloader, flashed TWRP all over again and then flashed custom ROM and Gapps. Everything running fine now.
Mods feel free to delete this post since it's solved itself, or leave it in case anyone needed help concerning the same issue, up to you.
Click to expand...
Click to collapse
Bibicp said:
I tried to factory reset a custom ROM, got sent to TWRP then I can't reboot to system from there. Tried a clean install but to no avail. I've looked around on the internet and I think I have to reinstall stock ROM and then reinstall custom recovery and ROM, except if I were to install the stock ROM once again (with sp tools) I need my phone to be turned off, not in recovery mode. So how exactly should I proceed now?
EDIT: Managed to get rid of the TWRP bootloop by restoring from a stock nandroid I've found on the forums, coupled with flashing a stock recovery image using TWRP. Reunlocked bootloader, flashed TWRP all over again and then flashed custom ROM and Gapps. Everything running fine now.
Mods feel free to delete this post since it's solved itself, or leave it in case anyone needed help concerning the same issue, up to you.
Click to expand...
Click to collapse
can you put a link where you find the stock recovery, cos i've restore stock recovery on twrp but my device keep booting to twrp