Hello, I tried searching for this but came up empty. I have a completely stock Nexus 4, received the OTA push for 4.3. Phone has never been rooted. After going through the install process it showed the android on it's back with a red triangle and said error. After a restart the phone just sits at the Google screen!!! I'm I boned or is there a fix for this? Any info would be greatly appreciated! Thank you!
Jesmuris said:
Hello, I tried searching for this but came up empty. I have a completely stock Nexus 4, received the OTA push for 4.3. Phone has never been rooted. After going through the install process it showed the android on it's back with a red triangle and said error. After a restart the phone just sits at the Google screen!!! I'm I boned or is there a fix for this? Any info would be greatly appreciated! Thank you!
Click to expand...
Click to collapse
Try going into fastboot and flashing the stock rom from google.
gmaxpwnage said:
Try going into fastboot and flashing the stock rom from google.
Click to expand...
Click to collapse
Not sure what mode I entered, Held vlm down + power. Says Fastboot Mode in red with a big green Start at the top. Options it gives me is Start, restart bootloader, recovery mode, and power off. If I try to enter Recovery mode it says no command. Don't see anything that allows me to reinstall
Jesmuris said:
Not sure what mode I entered, Held vlm down + power. Says Fastboot Mode in red with a big green Start at the top. Options it gives me is Start, restart bootloader, recovery mode, and power off. If I try to enter Recovery mode it says no command. Don't see anything that allows me to reinstall
Click to expand...
Click to collapse
Ok, found out on the no command screen I can hold power and hit vlm up and it brings me to system recovery with these options. Reboot system, apply update from ADB, wipe data/factory reset, wipe cache partition.
Not sure what to do sadly
Try following step:
1. Press Vol up and down and powerbutton same time to get to the fastboot mode as you mention.
2. Choice Recovery Mode and press power button. If you got luck you will see an android guy with red mark on the screen.
3. Press Vol Up and Power button same time for while don't let go it will pop up a list of option clean the cache and do factory reset, then reboot system.
If this method not working. Then hard method is flash your Nexus 4 with fastboot. Search the forum there few people already post how to flash 4.3 ROM with fastboot
Johnsonyc said:
Try following step:
1. Press Vol up and down and powerbutton same time to get to the fastboot mode as you mention.
2. Choice Recovery Mode and press power button. If you got luck you will see an android guy with red mark on the screen.
3. Press Vol Up and Power button same time for while don't let go it will pop up a list of option clean the cache and do factory reset, then reboot system.
If this method not working. Then hard method is flash your Nexus 4 with fastboot. Search the forum there few people already post how to flash 4.3 ROM with fastboot
Click to expand...
Click to collapse
Ok thank you, trying this now will update:good:
Didn't work Will try other method
Jesmuris said:
Didn't work Will try other method
Click to expand...
Click to collapse
Sorry to hear this bad news Hope the other method work for you!
Well, first try, couldn't get my PC to recognize fastboot in adb. Was getting frustrated beyond hell and had to walk away for a bit. Came back about an hour later and for some reason it finally recognized it... Back to the start screen like when I first bought the phone. So far working ok, except for being able to log into my google account... 2-step verification giving me issues now lol. Thank you again for your assistance. Very much appreciated!!:good::good:
Jesmuris said:
Well, first try, couldn't get my PC to recognize fastboot in adb. Was getting frustrated beyond hell and had to walk away for a bit. Came back about an hour later and for some reason it finally recognized it... Back to the start screen like when I first bought the phone. So far working ok, except for being able to log into my google account... 2-step verification giving me issues now lol. Thank you again for your assistance. Very much appreciated!!:good::good:
Click to expand...
Click to collapse
I had a similar experience (kind of). I had issues side-loading 4.2.2 -> 4.3 on my N4. After it finished update and rebooted I got a black screen and nothing more. I ran through it and tried to update to 4.3 again, and then it worked.
Even though it worked I've been noticing issues with it. For example, I now can no longer uninstall anything. When I attempt to uninstall any app, the phone reboots. I'm backing up now with Titanium and am about to flash. I was hoping there would be a quick fix here, but such is life. Viva la impatience.
I have same problem my stock 4.2.2 stuck x boot load , did vol up+dwn +power now stuck in "Download Mode" do not unplug the device until the process is complete .
oneguy77 said:
I have same problem my stock 4.2.2 stuck x boot load , did vol up+dwn +power now stuck in "Download Mode" do not unplug the device until the process is complete .
Click to expand...
Click to collapse
This is what I eventually followed to get mine working. I just did scenario 2 and that worked perfectly for me, so far no issues, just having to get things back to where I had them before. The second link is actually more detailed. Just make sure you follow step by step. I guess i could have not done step D10 but wanted to make sure this route worked for me. Thank you again for those who pointed me in the right direction
http://www.androidpolice.com/2013/0...-to-android-4-3-jwr66v-and-root-it-right-now/
http://forum.xda-developers.com/showpost.php?p=34552123&postcount=1
Jesmuris said:
Well, first try, couldn't get my PC to recognize fastboot in adb. Was getting frustrated beyond hell and had to walk away for a bit. Came back about an hour later and for some reason it finally recognized it... Back to the start screen like when I first bought the phone. So far working ok, except for being able to log into my google account... 2-step verification giving me issues now lol. Thank you again for your assistance. Very much appreciated!!:good::good:
Click to expand...
Click to collapse
I have the exact same problem but not sure how to get my PC to recognize fastboot in adb mode...
FYI if you flash to stock android 4.3 and you have the 16 GB Nexus 4, make sure that after you re-flash you have the full 16 GB and not 8 GB (unless you want to re-setup your phone twice like me). If you get this problem you can wipe cache and data from recovery and voila, all of your free space is back.
---------- Post added at 10:52 PM ---------- Previous post was at 10:44 PM ----------
zpilot said:
I have the exact same problem but not sure how to get my PC to recognize fastboot in adb mode...
Click to expand...
Click to collapse
If this is what I think it is, I was having the same problem. If I went into Control Panel on my PC and it would say that the driver is failing to load. To fix this I uninstalled the driver, rebooted, reinstalled Google USB Driver from the Android SDK Manager, restarted, and all was well after that.
I really have no explanation for why this fixed it, or it didn't work before, because other than fastboot, everything was working flawlessly with getting my phone to communicate with my PC.
Related
Hey guys
I tried the one-click root toolkit for mac from android rootz.
Something apparently has gone wrong during the root and I got some error messages and it didn't proceed. Next thing I know the nexus is stuck on google X logo and that's it. It won't load. I tried to recover through the recovery mode a couple of times but now I get the red warning sign when I go into recovery mode. This is only the second day I've had the nexus for. I feel like crying. Please Help
When the red sign appears press the volup down buttons and power button randomly until you get into recovery then factory reset
My 7 and 10 both did that. Just hold power until it turns off, then boot a recovery, wipe everything except system and reboot. It'll come up ok.
Sent from my Nexus 10 using Tapatalk HD
I'm having the same issue. However, the recovery I have installed is the non-functional CWM. So I can't factory reset. (I managed to once before CWM bombed, but it didn't change anything.)
I've tried several options via the toolkit. After fighting with the app all day it's finally wound up just saying it can't find adb? (I have a growing dislike for this app and have since uninstalled it.) Adb is right where it belongs and seems to run fine from cmd.
I also can't seem to flash anything via fastboot for some reason. The device throws "failinvaild id command" and fastboot immediately crashes on my laptop.
I managed to get it unlocked. However, I'm unable to flash anything to straighten it out...
Any help would be great.
scooterbaga said:
I'm having the same issue. However, the recovery I have installed is the non-functional CWM. So I can't factory reset. (I managed to once before CWM bombed, but it didn't change anything.)
I've tried several options via the toolkit. After fighting with the app all day it's finally wound up just saying it can't find adb? (I have a growing dislike for this app and have since uninstalled it.) Adb is right where it belongs and seems to run fine from cmd.
I also can't seem to flash anything via fastboot for some reason. The device throws "failinvaild id command" and fastboot immediately crashes on my laptop.
I managed to get it unlocked. However, I'm unable to flash anything to straighten it out...
Any help would be great.
Click to expand...
Click to collapse
Watch this video starting at the 6:30 mark.
http://www.youtube.com/watch?v=YtLvlrUDB04
bg1906 said:
Watch this video starting at the 6:30 mark.
http://www.youtube.com/watch?v=YtLvlrUDB04
Click to expand...
Click to collapse
Thanks for the info. My situation wasn't quite the same as my CWM was the real issue, which wouldn't run long enough to allow for the factory reset boot-loop solution. Kept at it and managed to get CWM to finish the individual formats/resets one at a time.
With a now bootable device, I'm off to replace the recovery... Thanks again.
Hey guys
i just wiped all my data and tried to reboot my nexus, but now it's been stuck on the google logo for ages...
trying to flash to stock + unroot with nexus toolkit doesn't work, any way to unbrick it?
please help...
do you have fastboot driver installed?
Step 1: Power down your Nexus 4 (hold the power button until it shuts off) before rebooting into fastboot mode. You can do this by holding down the the Volume Down and Power buttons simultaneously.
Step 2: Connect your device to your computer. Open up a terminal or command prompt, and navigate to the folder containing the fastboot program.
Step 3: Type fastboot devices into the command line, and you should then see your device’s ID, which means fastboot is setup correctly.
now go back to Nexus 4 toolkit. Flash back to stock.
badboy47 said:
do you have fastboot driver installed?
Step 1: Power down your Nexus 4 (hold the power button until it shuts off) before rebooting into fastboot mode. You can do this by holding down the the Volume Down and Power buttons simultaneously.
Step 2: Connect your device to your computer. Open up a terminal or command prompt, and navigate to the folder containing the fastboot program.
Step 3: Type fastboot devices into the command line, and you should then see your device’s ID, which means fastboot is setup correctly.
now go back to Nexus 4 toolkit. Flash back to stock.
Click to expand...
Click to collapse
works
thank you very much
fabian.m said:
works
thank you very much
Click to expand...
Click to collapse
Then, press on his THANKS button. That's the way we have to measure who contributes or not in xda-developers. Please, let's follow rules...
luiseteyo said:
Then, press on his THANKS button. That's the way we have to measure who contributes or not in xda-developers. Please, let's follow rules...
Click to expand...
Click to collapse
well.. technically thanking isn't in the rules.
exb0 said:
well.. technically thanking isn't in the rules.
Click to expand...
Click to collapse
It is in the good behaviour and politeness rules. Not everything is written.
Hi guys i got a similar problem, i flashed a walkman .zip wiped cache and dalvik cache. Then the phone booted into google logo, and it went all black. The display is on but its all black. The problem is i cannot power off the device. Holding all buttons just restarts the phone. What can i do?
I was on latest PA rom
Qbsti said:
Hi guys i got a similar problem, i flashed a walkman .zip wiped cache and dalvik cache. Then the phone booted into google logo, and it went all black. The display is on but its all black. The problem is i cannot power off the device. Holding all buttons just restarts the phone. What can i do?
I was on latest PA rom
Click to expand...
Click to collapse
reflash your rom. reboot your device, hold volune down before it reboots to get into the bootloader then recovery.
simms22 said:
reflash your rom. reboot your device, hold volune down before it reboots to get into the bootloader then recovery.
Click to expand...
Click to collapse
Thanks simms, i managed to get into fast boot between the reboots, and I flashed the rom and gapps.
Damn it scared me even more then the red light issue that happened to me last month.
Qbsti said:
Thanks simms, i managed to get into fast boot between the reboots, and I flashed the rom and gapps.
Damn it scared me even more then the red light issue that happened to me last month.
Click to expand...
Click to collapse
not booting after flashing something or modding something is the easiest of all to fix, just reflash the rom(gapps and kernel too if need be), no need to wipe anything. since i test all the trinity kernels before any get released, and pre-kernels, i get many that dont boot my device or bootloop(among some other funky behaviors), reflashing a good kernel always works
I left my phone for a few minutes, and when I picked it up it was bootlooped again, and i had to use fastboot again. What should I do now? Maybe a factory reset would help me. I don't want more unexpected bootloops. :/
swyped from my nexus 4
Qbsti said:
I left my phone for a few minutes, and when I picked it up it was bootlooped again, and i had to use fastboot again. What should I do now? Maybe a factory reset would help me. I don't want more unexpected bootloops. :/
swyped from my nexus 4
Click to expand...
Click to collapse
Try another rom. You might have downloaded corrupted zips. Also, make sure you flash the things you need first. Eg, flash rom and gapps. Don't restore anything if you're using titanium backup. Try restarting the phone, see if it gets into a bootloop. If it doesn't, then try restoring apps from TB. (if you use TB.)
Hi!
I´ve got a big problem. Today i flashed the new PA version, but it seems that the download had some issue. I could install it but after a while, I wanted to reboot the phone and it got stuck at the Google logo. I can only access fastboot mode and recovery.
So the problem is, i made a full wipe, so i have no rom on the sdcard anymore. Also I am now able to enable the debbuging mode. I tried every toolkit i couzld find, but everyone needs debugging mode enabled. windows doesnt recognize the phone ( it says unkown device). So i tried to install the adb drivers, but nothing happens.
i wanted to try to push a rom with adb on the phone but it says no device found. i am such a noob, i hope some can help me.
thx
I have a Verizon LG G2 I tried to flash my backed up stock recovery with Flashify so I could flash the most recent OTA. After accepting the OTA update my phone restarted, tried to install the update, hung at a black screen but was still turned on. If I power it off and back on it shows the LG logo, some white text, then goes to the same black screen. What appears to be happening is that my backup recovery did not restore properly and it's hanging when it tries to go into recovery. It's almost like my recovery partition is blank.
I've tried to follow the instructions to flash back to stock, but I do not believe I'm actually able to get my phone into download mode. When it is plugged into my windows 7 computer with the LG drivers installed it shows up in device manager as QHSUSB_BULK.
Is there any way for me to push a stock recovery, or even a custom recovery to my phone so I can somehow salvage it, or am I permanently bricked?
toopty said:
I have a Verizon LG G2 I tried to flash my backed up stock recovery with Flashify so I could flash the most recent OTA. After accepting the OTA update my phone restarted, tried to install the update, hung at a black screen but was still turned on. If I power it off and back on it shows the LG logo, some white text, then goes to the same black screen. What appears to be happening is that my backup recovery did not restore properly and it's hanging when it tries to go into recovery. It's almost like my recovery partition is blank.
I've tried to follow the instructions to flash back to stock, but I do not believe I'm actually able to get my phone into download mode. When it is plugged into my windows 7 computer with the LG drivers installed it shows up in device manager as QHSUSB_BULK.
Is there any way for me to push a stock recovery, or even a custom recovery to my phone so I can somehow salvage it, or am I permanently bricked?
Click to expand...
Click to collapse
I have the same exact problem. exactly the same. mine doesnt even show up for download mode. this sucks!
cgillie92 said:
I have the same exact problem. exactly the same. mine doesnt even show up for download mode. this sucks!
Click to expand...
Click to collapse
I'm still trying to find a solution I will post here if i have any luck. I've dug through a lot of forum posts and I think what makes us unique is the fact that we have a corrupt or blank recovery partition.
toopty said:
I'm still trying to find a solution I will post here if i have any luck. I've dug through a lot of forum posts and I think what makes us unique is the fact that we have a corrupt or blank recovery partition.
Click to expand...
Click to collapse
Ive looked through a lot too. and its crazy how that would happen i made sure it was rebooting correctly before i took the ota and then when i did the ota bam! only screens i can get to come up are the hardware key control mode and the factory hard reset which both go to white screens after I do them both. every one else probably has not taken the ota.
cgillie92 said:
Ive looked through a lot too. and its crazy how that would happen i made sure it was rebooting correctly before i took the ota and then when i did the ota bam! only screens i can get to come up are the hardware key control mode and the factory hard reset which both go to white screens after I do them both. every one else probably has not taken the ota.
Click to expand...
Click to collapse
One difference in what mine is doing and what your phone is doing. I go to a solid black screen not a white screen. It's very hard to tell my phone is even turned on. I'm having to look if the back-light to verify if it's on or not. I can hold my power button for 10 seconds through one LG logo cycle and then it turns off.
toopty said:
One difference in what mine is doing and what your phone is doing. I go to a solid black screen not a white screen. It's very hard to tell my phone is even turned on. I'm having to look if the back-light to verify if it's on or not. I can hold my power button for 10 seconds through one LG logo cycle and then it turns off.
Click to expand...
Click to collapse
I hope someone helps us out. I really cant afford a new one because the warranty is void. I was going back to stock because of all of the little bugs that need to be ironed out in roms. cause kit kat is around the corner hopefully and my problem virtually is the same i might have had my brightness on auto or something prior to that.
Foolow this tutorial to get your phone back.
http://forum.xda-developers.com/showthread.php?p=48765620
Partager.info said:
Foolow this tutorial to get your phone back.
http://forum.xda-developers.com/showthread.php?p=48765620
Click to expand...
Click to collapse
Thanks for the link. I'm tryingto follow the instructions,but when I get to the step where i plug in my phone it just showes up as a bunch of failes partitions, and slows my ubuntu to a crawl. I'm a linux noob, is there a command i can run to stop this from happening? I also created a reply asking this question in the link you sent me.
Thanks for the help.
Partager.info said:
Foolow this tutorial to get your phone back.
http://forum.xda-developers.com/showthread.php?p=48765620
Click to expand...
Click to collapse
After following the instructions on the above link i was able to get fastboot status on my phone. It did not fully restore my phone however. I was able to flash twrp via fastboot. I was then able to boot into twrp and run the command at this link via twrp terminal http://forum.xda-developers.com/showthread.php?t=2451696
Thanks to everyone for all your help.
toopty said:
Thanks for the link. I'm tryingto follow the instructions,but when I get to the step where i plug in my phone it just showes up as a bunch of failes partitions, and slows my ubuntu to a crawl. I'm a linux noob, is there a command i can run to stop this from happening? I also created a reply asking this question in the link you sent me.
Thanks for the help.
Click to expand...
Click to collapse
How did you get past the ubuntu slowing down? I cant win for ubuntu freezing due to all of the failed partitions either so close but yet so far =/
cgillie92 said:
How did you get past the ubuntu slowing down? I cant win for ubuntu freezing due to all of the failed partitions either so close but yet so far =/
Click to expand...
Click to collapse
Ignore all the message, unplug you phone get ready to type the command, plug it in and immediately press enter to run the command. it took some trial and error, and i had to use this other post to help me out. I actually got fastboot working first, then used this post to http://forum.xda-developers.com/showthread.php?t=2477595 to get download mode working, and to flash twrp recovery. After that i used this post to run the command line from with twrp. http://forum.xda-developers.com/showthread.php?t=2451696 . I didn't have to flash the factory tot to my phone, but i have that option now because download mode is working. This process will work, there is hope for you getting your phone back. I'm fully recovered. I decided 12B is not worth it in the mean time, but if you want 12B you need to flash the factory tot and then upgrade. There is a way to root 12B, but as of this time you are unable to get Custom Recovery on it.
i tried going back to stock firmware using the method in general section but i always seem to get an error at 49%. can someone explain how to get passed this.
i using the t-mobile d801.
also my recovery seemed to have gotten erased because i cant boot into twrp anymore.
LG G2 Stuck @ 49%
El Killer said:
i tried going back to stock firmware using the method in general section but i always seem to get an error at 49%. can someone explain how to get passed this.
i using the t-mobile d801.
also my recovery seemed to have gotten erased because i cant boot into twrp anymore.
Click to expand...
Click to collapse
HEY! I'm on the d801 as well and I've been where you're at a number of times, unfortunately. But I've always gotten out. Here's the conclusion I've reached. Trying to flash directly back to stock without wiping all the partitions first is what makes the RDTool get stuck. It's like the phone runs out of memory and can't host a full Gig+ of data since your last ROM is in the way. Sorry if I'm wrong but I'm only assuming you didn't wipe everything except the Internal storage. The good thing every time this has happened to me is that your recovery partition should be intact. Mine always is, and we're on the same variant. Another thing, booting back into recovery is not impossible. It's all in the timing it takes from the first time you see the LG logo while holding volume - and the power button, but don't let go. What worked for me was to let the phone cycle between off and boot power states twice until the phone is completely off again. You may even notice the LED indicator flash red. Release your keys if the phone stays off and immediately hold the combo down again until the phone tries to boot again just don't let go of the buttons. Once it powers down again, leave the phone alone for a few minutes. Come back and this time get ready to boot into recovery. The combo button press will initiate boot but don't let go until the next time you see the LG logo flash, then quickly release and depress the vol down power up combo and hold. May take a minute longer than usual but the reset menu should pop up thereafter. Tap power 2 more times and you should back into recovery. It's worked every time for me. Let me know if you're good and whether this helped!
Good Luck,
tinydynamite00
try with x86
El Killer said:
i tried going back to stock firmware using the method in general section but i always seem to get an error at 49%. can someone explain how to get passed this.
i using the t-mobile d801.
also my recovery seemed to have gotten erased because i cant boot into twrp anymore.
Click to expand...
Click to collapse
i had exact same issue that progress stucked on 49%. if you are using 64bit OS, try to flash it with 32bit(x86) OS
good luck
tinydynamite00 said:
HEY! I'm on the d801 as well and I've been where you're at a number of times, unfortunately. But I've always gotten out. Here's the conclusion I've reached. Trying to flash directly back to stock without wiping all the partitions first is what makes the RDTool get stuck. It's like the phone runs out of memory and can't host a full Gig+ of data since your last ROM is in the way. Sorry if I'm wrong but I'm only assuming you didn't wipe everything except the Internal storage. The good thing every time this has happened to me is that your recovery partition should be intact. Mine always is, and we're on the same variant. Another thing, booting back into recovery is not impossible. It's all in the timing it takes from the first time you see the LG logo while holding volume - and the power button, but don't let go. What worked for me was to let the phone cycle between off and boot power states twice until the phone is completely off again. You may even notice the LED indicator flash red. Release your keys if the phone stays off and immediately hold the combo down again until the phone tries to boot again just don't let go of the buttons. Once it powers down again, leave the phone alone for a few minutes. Come back and this time get ready to boot into recovery. The combo button press will initiate boot but don't let go until the next time you see the LG logo flash, then quickly release and depress the vol down power up combo and hold. May take a minute longer than usual but the reset menu should pop up thereafter. Tap power 2 more times and you should back into recovery. It's worked every time for me. Let me know if you're good and whether this helped!
Good Luck,
tinydynamite00
Click to expand...
Click to collapse
still no luck
El Killer said:
still no luck
Click to expand...
Click to collapse
OK. So tell me, what ROM were you on, which recovery version and name are you using, why were you flashing back to stock, i.e. were you having problems, what kind. Explain as much as you can in detail. Need to retrace your exact steps to best get you fixed up!
tinydynamite00
tinydynamite00 said:
OK. So tell me, what ROM were you on, which recovery version and name are you using, why were you flashing back to stock, i.e. were you having problems, what kind. Explain as much as you can in detail. Need to retrace your exact steps to best get you fixed up!
tinydynamite00
Click to expand...
Click to collapse
i was using pa4.0 and wanted to go back to stock because i preffered the lg ui. i had twrp 2.6.3.5 i restored my back up of stock but when i rebooted i got into fastboot mode.
twrp wasnt working after i had restored my back up go straight to fastboot was stuck in fastboot until i found a thread explaining how to get out of fastboot and restore download mode.
managed to get download mode working and tried to flash stock with mobile support tool and got the 49 percent error,
my phone never really displayed any progress just says download mode with a white box and blue dots
El Killer said:
i was using pa4.0 and wanted to go back to stock because i preffered the lg ui. i had twrp 2.6.3.5 i restored my back up of stock but when i rebooted i got into fastboot mode.
twrp wasnt working after i had restored my back up go straight to fastboot was stuck in fastboot until i found a thread explaining how to get out of fastboot and restore download mode.
managed to get download mode working and tried to flash stock with mobile support tool and got the 49 percent error,
my phone never really displayed any progress just says download mode with a white box and blue dots
Click to expand...
Click to collapse
K, now if you're only seeing the blue dots when you attach by USB your phone to PC, then you're not fully in DL mode to process the kdz. You should see a white wheel in the center of the screen when you connect and a viewing mirror near the base of your phone with ROOTED in red directly below that. And you're sure your PC is detecting your phone? You've the drivers installed? Because when RDT tells you to run the tool, you'll see some binary code in the viewing window I spoke of, the white wheel will turn and below it will be shown the COM port to which you're connected and a solid thin red bar will begin to fill a space in the viewer showing you the progress.
Also, be sure when attempting the first steps I gave you to boot into recovery that you are not USB connected. It won't work.
And, try to remember if your phone was well enough charged, should have been at least 80% full. It happened to me once that I couldn't boot recovery and my phone would go to fastboot like yours until I left it alone to charge and then I repeated the stepsvi laid out to get back into recovery. This part is paramount!
Please READ CAREFULLY
I used to be in your same situation. I thought I had bricked my phone for good. I finally figured it out. Here is my solution from my Thread.
Esteef said:
Okay, after 12+ hours of trying every method possible on XDA I finally resolved my issue. I will update the first post just incase any others care or fall into the same dilemma I was in.
The LG Mobile Support tool would not download the firmware and it would NOT ask me for my IMEI to download it either.
So my solution....
***
Installed LG Mobile Support Tool then Installed the LG Drivers. (FROM HERE http://forum.xda-developers.com/showthread.php?t=2471370
BEFORE I connected the phone to the computer. I opened the LG Mobile support tool clicked (Options on the top right).
When the dropped down opened, I clicked the (Upgrade Recovery) option. THEN, is when the prompt opened to ask me what my IMEI is.
Before I entered my IMEI, I connected my phone to the computer in download mode, then proceeded to enter my IMEI and hit OK.
This is when the LG Mobile Support tool SUCCESSFULLY downloaded the latest official LG firmware and installed it.
*** BE AWARE, with the phone connected to the PC, the prompt NEVER appeared to enter my IMEI.
*** But with the phone disconnected, the prompt came up every time. This might be the trick for some people.
*** with the IMEI prompt opened, I then connected the phone , entered the IMEI, then hit OK. BOOM HERPES....
Well I'll polish this up more later. I hope this works for every LG G2 Variant and not just the T-Mobile one (D801)
-Esteef
Click to expand...
Click to collapse
THIS WILL WIPE YOUR PHONE COMPLETELY...
tinydynamite00 said:
K, now if you're only seeing the blue dots when you attach by USB your phone to PC, then you're not fully in DL mode to process the kdz. You should see a white wheel in the center of the screen when you connect and a viewing mirror near the base of your phone with ROOTED in red directly below that. And you're sure your PC is detecting your phone? You've the drivers installed? Because when RDT tells you to run the tool, you'll see some binary code in the viewing window I spoke of, the white wheel will turn and below it will be shown the COM port to which you're connected and a solid thin red bar will begin to fill a space in the viewer showing you the progress.
Also, be sure when attempting the first steps I gave you to boot into recovery that you are not USB connected. It won't work.
And, try to remember if your phone was well enough charged, should have been at least 80% full. It happened to me once that I couldn't boot recovery and my phone would go to fastboot like yours until I left it alone to charge and then I repeated the stepsvi laid out to get back into recovery. This part is paramount!
Click to expand...
Click to collapse
yeah my computer does recognize my phone. but i cant run adb or fastboot anymore. all drivers are installed also.
i never got the while wheel or any progress indicator. so i guees im not really in download mode.
i let my phone charge for a few hours and try your method again and let you know what happens
El Killer said:
yeah my computer does recognize my phone. but i cant run adb or fastboot anymore. all drivers are installed also.
i never got the while wheel or any progress indicator. so i guees im not really in download mode.
i let my phone charge for a few hours and try your method again and let you know what happens
Click to expand...
Click to collapse
Sounds good. A full charge can make all the difference. I learnt the hard way! One or more of us will be along should you need further help.
I do hope you get this sorted! I've come back from the brink too many times to not believe you won't.
tinydynamite00
Do as esteef recommended..
Sent from my LG-D802 using XDA Premium 4 mobile app
Falaco147 said:
Do as esteef recommended..
Sent from my LG-D802 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
im trying but i get a battery to low error. i guess i need to charge it longer
i owe you all a million thanks for helping me unbrick my phone. i really thought i was left with a paper weight and then i tried esteefs method again i really owe you guys thank you for the support
El Killer said:
i owe you all a million thanks for helping me unbrick my phone. i really thought i was left with a paper weight and then i tried esteefs method again i really owe you guys thank you for the support
Click to expand...
Click to collapse
You are welcome... The first time I did it too my battery was at 28% and I panicked since I got the low battery error.
I could of sworn that my phone officially became a paper weight. My heart dropped.
I'm glad you are up and running with the rest of us!
-Esteef
1732359994
hey !
I have the same problem, but... I can't acces to the recovery :/ i tried to install CWM (with Freegee) over Team win recovery and... boot loop :
The rom 4.2.2 flex was gone, no boot animation
-When i pres volum down + power, i have the reset menu, but after that, there is a black screen and it's written at the top left "started usb_start Fastboot Mode ()"
Please, i need your help, i'm so afraid !!
Thx !
Esteef said:
I used to be in your same situation. I thought I had bricked my phone for good. I finally figured it out. Here is my solution from my Thread.
THIS WILL WIPE YOUR PHONE COMPLETELY...
Click to expand...
Click to collapse
I know this thread is a bit old, but it saved my butt. Your method worked perfectly. Thank you for this post.
My LG F460 was bricked (error 570), only download mode was working. Esteef method works fine even my pictures and programs was saved. Thanks!
I got the new T-mobile LG V20 I went thru the the whole proccess step by step of how to root and install twrp on my device the last step of having to encrypt it failed now its stuck in a bootloop. screen pops up saying encryption is unsuccessful,then resets to twrp and flashes back to the previous screen. over and over. Please help
jessiemougeot said:
I got the new T-mobile LG V20 I went thru the the whole proccess step by step of how to root and install twrp on my device the last step of having to encrypt it failed now its stuck in a bootloop. screen pops up saying encryption is unsuccessful,then resets to twrp and flashes back to the previous screen. over and over. Please help
Click to expand...
Click to collapse
same problem here and cant find solution ...
I had the same issue. when you press to reset button when the phone boots it should reboot and for a short time go to recovery and try to write some commands, right? if it does like mine did then what i did to fix it was boot up the phone and wait for the page saying encryption unsuccesful to popup and on the computer have the adb reboot recovery ready to go so when you press the reset button and the recovery menu pops up press enter on the computer before it goes away and it should send you to the regular recovery menu. from there you should go back to wipe and press the format data button where you have to type yes to erase everything. let me know how it went.
you will have to reflash the supersu but it should now be working like it should
Flash the latest su and your fine.
ErickF said:
I had the same issue. when you press to reset button when the phone boots it should reboot and for a short time go to recovery and try to write some commands, right? if it does like mine did then what i did to fix it was boot up the phone and wait for the page saying encryption unsuccesful to popup and on the computer have the adb reboot recovery ready to go so when you press the reset button and the recovery menu pops up press enter on the computer before it goes away and it should send you to the regular recovery menu. from there you should go back to wipe and press the format data button where you have to type yes to erase everything. let me know how it went.
you will have to reflash the supersu but it should now be working like it should
Click to expand...
Click to collapse
did that but my adb says no devices or emulators?
jo4mvp24 said:
did that but my adb says no devices or emulators?
Click to expand...
Click to collapse
Make sure your on charging mode and you have adb debug enabled
send the adb reboot recovery command as soon as the twrp connects to the computer. as soon as you hear it connect to the computer it should work if your drivers are working.
charlieb620 said:
Make sure your on charging mode and you have adb debug enabled
Click to expand...
Click to collapse
how do i do that when phone stuck on encryption unsuccessful screen?
exactly my issue
ErickF said:
I had the same issue. when you press to reset button when the phone boots it should reboot and for a short time go to recovery and try to write some commands, right? if it does like mine did then what i did to fix it was boot up the phone and wait for the page saying encryption unsuccesful to popup and on the computer have the adb reboot recovery ready to go so when you press the reset button and the recovery menu pops up press enter on the computer before it goes away and it should send you to the regular recovery menu. from there you should go back to wipe and press the format data button where you have to type yes to erase everything. let me know how it went.
you will have to reflash the supersu but it should now be working like it should
Click to expand...
Click to collapse
Ya that is exactly what happend give me a few minutes ill try it out and let you know....THANKS...THANKS....THANKS...It worked, i got it on my first try. Your right ...you have to be quick. thank u so much you saved me along night of downloads! :victory:
This method WORKS!!!! Same situation happened to me. THANK YOU 500x!! you saved my brick!
ErickF said:
I had the same issue. when you press to reset button when the phone boots it should reboot and for a short time go to recovery and try to write some commands, right? if it does like mine did then what i did to fix it was boot up the phone and wait for the page saying encryption unsuccesful to popup and on the computer have the adb reboot recovery ready to go so when you press the reset button and the recovery menu pops up press enter on the computer before it goes away and it should send you to the regular recovery menu. from there you should go back to wipe and press the format data button where you have to type yes to erase everything. let me know how it went.
you will have to reflash the supersu but it should now be working like it should
Click to expand...
Click to collapse
This works 100% thank you so much. Just have patience as it has to be at the right time....WORKS WORKS WORKS!!!!!
Help
Can someone explain the commands and how to do this please thanks in advance
I did the data reset and im still in the bootloop. Worst thing is now i cant seem to get into recovery
epr2175 said:
I did the data reset and im still in the bootloop. Worst thing is now i cant seem to get into recovery
Click to expand...
Click to collapse
What screen are you stuck in? Do you have adb up and running?
Same as before Encryption unsuccessful. I was able to do the trick, got into two and wiped data. Then rebooted to system and it went right back to that screen. I've tried 100 times or so to get back into twrp with no luck. I hear the computer recognize the device when it goes into twrp for 2 seconds after you click reset. Not sure if that means add is up and running or not.
jessiemougeot said:
Ya that is exactly what happend give me a few minutes ill try it out and let you know....THANKS...THANKS....THANKS...It worked, i got it on my first try. Your right ...you have to be quick. thank u so much you saved me along night of downloads! :victory:
Click to expand...
Click to collapse
Well it booted then got stuck on the lg boot screen again. Adb does not recognize my device, can only boot into Fastboot. Fastboot does see my device, tried lgup, lg bridge, and lg update none see my device, tried relocking bootloader after oem lock bootloader rebooted said my device was corrupted and shut itself off went back into Fastboot unlocked bootloader again and back to the same lg screen help?
This did not work for me, my phone reboots back into TWRP whenever I install a system image it still gives me the encryption message.
---------- Post added at 02:06 PM ---------- Previous post was at 01:11 PM ----------
crazyc78 said:
This did not work for me, my phone reboots back into TWRP whenever I install a system image it still gives me the encryption message.
Click to expand...
Click to collapse
Now I don't even have the encryption screen it just reboots back to TWRP very frustrating!!
fixed!
jessiemougeot said:
I got the new T-mobile LG V20 I went thru the the whole process step by step of how to root and install twrp on my device the last step of having to encrypt it failed now its stuck in a bootloop. screen pops up saying encryption is unsuccessful,then resets to twrp and flashes back to the previous screen. over and over. Please help
Click to expand...
Click to collapse
Had the same problem and could not for the life of me do the adb thing. Someone here stated something that I thought I'd try: Press volume down while plugging in the phone to get into fastboot. In a command window issue "fastboot oem lock" (this will relock the boot) > Let the phone reset and you'll see the "Phone corrupt message" > Plug the phone in again to do a fastboot and issue "fastboot oem unlock" > Take the battery out let the phone boot and BAM-E WHAM success!
btw. I followed the steps here to do the whole root thing with Android . how (google "how to root the v20")
I think the "data" wipe did this and according to this site it's not a necessary step so skip it.
This option works!
SyHusky said:
Had the same problem and could not for the life of me do the adb thing. Someone here stated something that I thought I'd try: Press volume down while plugging in the phone to get into fastboot. In a command window issue "fastboot oem lock" (this will relock the boot) > Let the phone reset and you'll see the "Phone corrupt message" > Plug the phone in again to do a fastboot and issue "fastboot oem unlock" > Take the battery out let the phone boot and BAM-E WHAM success!
btw. I followed the steps here to do the whole root thing with Android . how (google "how to root the v20")
I think the "data" wipe did this and according to this site it's not a necessary step so skip it.
Click to expand...
Click to collapse
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
I go my T-mobile LG V20 H918 on 11/23/16 and sure enough, I followed the same thread as listed above where it added the step of "data wipe" crap. I was caught in a bootloop, where phone kept bootlooping back to the "reset to factory." The other method of entering the adb command at the right time was more frustrating than anything. (I never got it to work). I spent all day yesterday trying to get this phone working. I re-read (x30) the above thread and on the first attempt it worked. I did not get the "Phone Corrupt Message," but I went ahead and entered the "fastboot oem unlock" and the F#$king phone finally reboot to the setup initial screen. It wiped everything, but having a phone working rather than a nice $800 paperweight, I wanted to kiss SkyHusky for sharing this simple method. YOU ARE AWESOME!!!!
By the way, since I am a glutton for punishment, I followed the steps to root again. After flashing the SuperUser, I rebooted to System. I was at the initial setup screen. My phone is rooted, has TWRP, and SuperUser! As soon as I got the phone working, I went back to TWRP and made a BACKUP!!!!
It is amazing that every time I f-up a phone, I can always come to XDA and get a solution. THANKS GUYS!
jay_h_jacob said:
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
I go my T-mobile LG V20 H918 on 11/23/16 and sure enough, I followed the same thread as listed above where it added the step of "data wipe" crap. I was caught in a bootloop, where phone kept bootlooping back to the "reset to factory." The other method of entering the adb command at the right time was more frustrating than anything. (I never got it to work). I spent all day yesterday trying to get this phone working. I re-read (x30) the above thread and on the first attempt it worked. I did not get the "Phone Corrupt Message," but I went ahead and entered the "fastboot oem unlock" and the F#$king phone finally reboot to the setup initial screen. It wiped everything, but having a phone working rather than a nice $800 paperweight, I wanted to kiss SkyHusky for sharing this simple method. YOU ARE AWESOME!!!!
By the way, since I am a glutton for punishment, I followed the steps to root again. After flashing the SuperUser, I rebooted to System. I was at the initial setup screen. My phone is rooted, has TWRP, and SuperUser! As soon as I got the phone working, I went back to TWRP and made a BACKUP!!!!
It is amazing that every time I f-up a phone, I can always come to XDA and get a solution. THANKS GUYS!
Click to expand...
Click to collapse
No problem!! Also I forgot to add I only rooted afterward and didn't try to install a ROM or anything. I would think you risk danger with some ROMs without that decryption thing turned off. So maybe in the short future there will be better fixes.