Related
Hi All,
I tried installing CMW on my AT&T galaxy S4 and now the the device is stuck on boot showing 'recovery booting...'
I have tried holding down vol up + power + home key but issue still persists.
I followed the steps in this link: galaxys4root.com/galaxy-s4-root/how-to-install-cwm-recovery-on-att-or-verizon-galaxy-s4-sgh-i337sch-i545/
Attached is a screenshot to further clarify: sdrv.ms/16drSEy
Only way to turn off device is to disconnect the battery.
Any ideas on how to resolve?
It's too late now but don't go to galaxys4root. Use xda. Do you know what firmware you were on? Was it mf3, etc?
If you were on MF3, you hosed it.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
jd1639 said:
It's too late now but don't go to galaxys4root. Use xda. Do you know what firmware you were on? Was it mf3, etc?
Click to expand...
Click to collapse
Definitely will not go to galaxys4root again. I do not think I was on MF3 but I am not sure.
The firmware was the same as when I first bought it on release date. Not sure if that helps.
Can I unbrick it with odin?
Unless you froze or deleted the files for OTA, it is impossible for you to still be on the same firmware from release. MF3 auto updates after 3 days of it being downloaded.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
we4321 said:
Definitely will not go to galaxys4root again. I do not think I was on MF3 but I am not sure.
I firmware was the same as when I first bought on release date. Not sure if that helps.
Can I unbrick it with odin?
Click to expand...
Click to collapse
If you're not on mf3, yes. Do know if it ever updated itself after you got it.
jd1639 said:
If you're not on mf3, yes. Do know if it ever updated itself after you got it.
Click to expand...
Click to collapse
I am not sure to be honest. I never activated the phone with at&t as I was wanting to install Cyanogen before activating it.
I have downloaded apps to it so it was connected via wifi.
By default would it auto update to mf3 via wifi and not connected to at&t yet?
we4321 said:
I am not sure to be honest. I never activated the phone with at&t as I was wanting to install Cyanogen before activating it.
I have downloaded apps to it so it was connected via wifi.
By default would it auto update to mf3 via wifi and not connected to at&t yet?
Click to expand...
Click to collapse
Probably not. At this point out probably won't hurt to try to flash the mdl firmware with odin
Edit here is a link. You can get the mdl firmware at sammobile.com. the link has mdb firmware. I'd recommend downloading mdl and using it with the guide in the link. http://forum.xda-developers.com/showthread.php?p=40976805
jd1639 said:
Probably not. At this point out probably won't hurt to try to flash the mdl firmware with odin
Click to expand...
Click to collapse
Can you point me to the proper steps/tutorial on how to flash the mdl firmware with odin for this at&t s4 device?
I rather make sure I use the right information this time.
jd1639 said:
Probably not. At this point out probably won't hurt to try to flash the mdl firmware with odin
Edit here is a link. You can get the mdl firmware at sammobile.com. the link has mdb firmware. I'd recommend downloading mdl and using it with the guide in the link. http://forum.xda-developers.com/showthread.php?p=40976805
Click to expand...
Click to collapse
Awesome. I will give this a try tomorrow morning as it is getting late on my end. I will update this post tomorrow with the results.
Thanks for your quick reply. Much appreciated.
As long as you never connected to AT&T cellular network, you are good to flash and attempt to fix it.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
we4321 said:
Awesome. I will give this a try tomorrow morning as it is getting late on my end. I will update this post tomorrow with the results.
Thanks for your quick reply. Much appreciated.
Click to expand...
Click to collapse
UPDATE: These steps worked and my phone is now operational again! Guess I do not have MF3 firmware.
Question, is how do I get cyanogenmod installed at this point? I followed this guide on cyanogenmod site: http://wiki.cyanogenmod.org/w/Install_CM_for_jflteatt
but got into trouble while trying to install ClockWorkMod.
Should I use the steps on cyanogenmod and request assistance for CWM OR is there a better method?
BTW, just want to say thanks to jd1639 and graydiggy. You guys know your stuff!
Thank you......
we4321 said:
UPDATE: These steps worked and my phone is now operational again! Guess I do not have MF3 firmware.
Question, is how do I get cyanogenmod installed at this point? I followed this guide on cyanogenmod site: http://wiki.cyanogenmod.org/w/Install_CM_for_jflteatt
but got into trouble while trying to install ClockWorkMod.
Should I use the steps on cyanogenmod and request assistance for CWM OR is there a better method?
BTW, just want to say thanks to jd1639 and graydiggy. You guys know your stuff!
Thank you......
Click to expand...
Click to collapse
Use this to guide you. http://forum.xda-developers.com/showthread.php?p=42320391
jd1639 said:
Use this to guide you. http://forum.xda-developers.com/showthread.php?p=42320391
Click to expand...
Click to collapse
Nice. I'll give this a go. Thanks
Alright, so I've been doing rooting things for a long time...and never have I had this many problems. I posted something here earlier about rooting my S4, installing ROMs and having it hang on the Samsung Galaxy S4 Screen. So I figured I would try booting with Odin and re-installing a stock image. No luck. I keep getting this show up on my Galaxy S4 when I click start -- "secure check failed" and Odin shows a fail.
I don't even know where to go from here because I'm looking at an expensive paperweight at this point. Has anyone ever seen this before or even know where I can start. Any help would really be appreciated...at this point I just feel defeated.
-Stalker
Are you using the correct firmware? You werent on MF3 were you?
Sent from my SAMSUNG-SGH-I467 using Tapatalk 4
agent929 said:
Are you using the correct firmware? You werent on MF3 were you?
Sent from my SAMSUNG-SGH-I467 using Tapatalk 4
Click to expand...
Click to collapse
I believe I was using the correct firmware. I followed the instructions in the Q&A thread. I was NOT on MF3.
Hoping to get this figured out
a.stalker22 said:
I believe I was using the correct firmware. I followed the instructions in the Q&A thread. I was NOT on MF3.
Hoping to get this figured out
Click to expand...
Click to collapse
I always get firmware from sammobile.com. Download the firmware ending in mdl. It'll be a zip file. Use 7-zip to extract the .tar.md5 file from it and use that in Odin.
jd1639 said:
I always get firmware from sammobile.com. Download the firmware ending in mdl. It'll be a zip file. Use 7-zip to extract the .tar.md5 file from it and use that in Odin.
Click to expand...
Click to collapse
I'll download the firmware there and see if that solves my issue. Is there any way this could be related to the kernel? If I restore this firmware I will lose my root, correct?
a.stalker22 said:
I'll download the firmware there and see if that solves my issue. Is there any way this could be related to the kernel? If I restore this firmware I will lose my root, correct?
Click to expand...
Click to collapse
You will lose root. Odin should put everything back on like it was new. You do have to register on sammobile to download the firmware, but it's free.
jd1639 said:
You will lose root. Odin should put everything back on like it was new. You do have to register on sammobile to download the firmware, but it's free.
Click to expand...
Click to collapse
Yeah I saw that. I'm registering now and hopefully this will work. If I run into any more problems I'll let you know.
jd1639 said:
You will lose root. Odin should put everything back on like it was new. You do have to register on sammobile to download the firmware, but it's free.
Click to expand...
Click to collapse
Hey man..that was it! I really appreciate all of the help...you have no idea! :laugh:
a.stalker22 said:
Hey man..that was it! I really appreciate all of the help...you have no idea! :laugh:
Click to expand...
Click to collapse
Great to hear!
Can anyone direct me to the I337UCUAMF3 official firmware?
jsull35 said:
Can anyone direct me to the I337UCUAMF3 official firmware?
Click to expand...
Click to collapse
None available, but I suggest you use the search function and do some reading because this has been mentioned dozens of times already. The best you can do at this point is take the phone to a BestBuys with a Sumsung Kiosk and see if they will reflash it. You need to search to find out more information about it.
scott14719 said:
None available, but I suggest you use the search function and do some reading because this has been mentioned dozens of times already. The best you can do at this point is take the phone to a BestBuys with a Sumsung Kiosk and see if they will reflash it. You need to search to find out more information about it.
Click to expand...
Click to collapse
Yea, this is the second time this week my phone has bricked for no reason. At&t warranty center ran the samsung tool on it last time and fixed it.
jsull35 said:
Yea, this is the second time this week my phone has bricked for no reason. At&t warranty center ran the samsung tool on it last time and fixed it.
Click to expand...
Click to collapse
Sounds like it needs to be replaced (warranty or insurance), but I would try for warranty first. If it bricked for no reason at all, I assume you are not rooted and have nothing custom on the phone? Because if you do, it could prevent a warranty claim. Samsung can and will send you a bill if they find anything has been tampered with. Good luck.
You can check here...
Mind you however, that is ONLY for devices running pre-MF3 bootloaders. If you attempt to flash it as a stock recovery on a MF3 device your end up with a brick. If your on MF3 and have a brick currently, there isn't a way to go back outside of sending the phone back to Samsung or going to Best Buy's Samsung Experience Center.
jsull35 said:
Can anyone direct me to the I337UCUAMF3 official firmware?
Click to expand...
Click to collapse
https://mega.co.nz/#!WEEzSA7Z!aB46731_AwM7P83eMdDlmFYd1hUZfFBcQAZjc1X7wAE Here ya go Hope it works. Thx to @Shockndrop for the files.
Get the new EMJ6. Even beta is fine.
BaSingSe said:
Get the new EMJ6. Even beta is fine.
Click to expand...
Click to collapse
Why? You're just locked down that much tighter. No root, no custom roms
jd1639 said:
Why? You're just locked down that much tighter. No root, no custom roms
Click to expand...
Click to collapse
cant you use safestrap for custom roms?
nabears101 said:
cant you use safestrap for custom roms?
Click to expand...
Click to collapse
not on mj6
nabears101 said:
https://mega.co.nz/#!WEEzSA7Z!aB46731_AwM7P83eMdDlmFYd1hUZfFBcQAZjc1X7wAE Here ya go Hope it works. Thx to @Shockndrop for the files.
Click to expand...
Click to collapse
This is by far your best option, use ODIN and flash these files to return to a stock MF3. Updating to anything higher then MF3 is generally ill-advised. At least for the moment...
nabears101 said:
cant you use safestrap for custom roms?
Click to expand...
Click to collapse
Have you tested or seen anyone else report that the current Safestrap works with MJ6 or you can even gain root access with MJ6?
Not being rude, but please don't offer advice if you are unsure of the outcome (this means more than one person has confirmed working or you have tested it yourself). I personally don't think it hurts to make a suggestion but let the person know it hasn't been tested or you are unsure of the outcome.
Had the OP taken your advice before you were corrected, they would have been upgraded to MJ6 with no option for running a custom ROM or getting root access (hopefully this won't be the case for long).
NighthawkXL said:
This is by far your best option, use ODIN and flash these files to return to a stock MF3. Updating to anything higher then MF3 is generally ill-advised. At least for the moment...
Click to expand...
Click to collapse
The rar file in the link above comes with 5 files.
BOOTLOADER_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5
CSC_ATT_I337ATTAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5
MODEM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5
PLATFORM_I337UCUAMF3_812098_REV06_user_low_ship_MULTI_CERT.tar.md5
SS_DL.dll
Odin (v3.07) has 4 slots for different files:
Bootloader
PDA
Phone
CSC
My question is which files go in which slot for redownloading mf3 to a soft bricked mf3 s4?
Zeltex said:
My question is which files go in which slot for redownloading mf3 to a soft bricked mf3 s4?
Click to expand...
Click to collapse
Here is a link showing what this person did. Do not use the SS_DL.dll
http://forum.xda-developers.com/showpost.php?p=46943206&postcount=30
~wolverine~ said:
Here is a link showing what this person did. Do not use the SS_DL.dll
http://forum.xda-developers.com/showpost.php?p=46943206&postcount=30
Click to expand...
Click to collapse
The CSC file seems to be giving me problems. I've tried different versions of ODIN (v3.04,3.07,3.09,1.85) and they all have the same problem.
Zeltex said:
The CSC file seems to be giving me problems. I've tried different versions of ODIN (v3.04,3.07,3.09,1.85) and they all have the same problem.
Click to expand...
Click to collapse
I'm on windows 8.1 pro 64bit & used Odin v1.85. worked perfectly.
Zeltex said:
The CSC file seems to be giving me problems. I've tried different versions of ODIN (v3.04,3.07,3.09,1.85) and they all have the same problem.
Click to expand...
Click to collapse
Probably a bad download
jd1639 said:
Probably a bad download
Click to expand...
Click to collapse
I redownloaded the files again and Odin is still crashing whenever I press start.
Zeltex said:
I redownloaded the files again and Odin is still crashing whenever I press start.
Click to expand...
Click to collapse
I saw your other post with the Odin print out. It looks to me like it's still a bad download, the md5 is not checking.
Edit, what are you using to extract the md5 files from the zip? Use 7-zip.
jd1639 said:
I saw your other post with the Odin print out. It looks to me like it's still a bad download, the md5 is not checking.
Edit, what are you using to extract the md5 files from the zip? Use 7-zip.
Click to expand...
Click to collapse
That might be the case I've been using winrar to extract the files. Not sure if it should make a difference but will try
Any help would be appreciated! Trying o Odin to 100% stock MJA. Need the original stock recovery before I can do anything... Thanks to anyone that can help. Merry Xmas (eve)!
Joe0113 said:
Any help would be appreciated! Trying o Odin to 100% stock MJA. Need the original stock recovery before I can do anything... Thanks to anyone that can help. Merry Xmas (eve)!
Click to expand...
Click to collapse
Just Odin in the stock MJA.tar.md5. You can find a link to it here: http://forum.xda-developers.com/showthread.php?t=2509605
Darnell0216 said:
Just Odin in the stock MJA.tar.md5. You can find a link to it here: http://forum.xda-developers.com/showthread.php?t=2509605
Click to expand...
Click to collapse
Yes I already have that, but I want to use Triangle Away first... and to use that you need to have he stock recovery lol.
Joe0113 said:
Yes I already have that, but I want to use Triangle Away first... and to use that you need to have he stock recovery lol.
Click to expand...
Click to collapse
Shoudn't need to, when I ODINed back to stock, it removed the text from the bootscreen.
theheathen said:
Shoudn't need to, when I ODINed back to stock, it removed the text from the bootscreen.
Click to expand...
Click to collapse
Guess I'll just Odin the stock MJA tar then. Thanks brotha.
I am root on MF3 and I can not turn on WiFi
That's nice. A little more info would be helpful. Are you on a custom room or stock. Did it just start doing this.
Im on stock and tried to flash a kernel
jd1639 said:
That's nice. A little more info would be helpful. Are you on a custom room or stock. Did it just start doing this.
Click to expand...
Click to collapse
ZOOPidy said:
Im on stock and tried to flash a kernel
Click to expand...
Click to collapse
That's your problem. You can't flash kernels on mf3. You'll probably have to odin the mf3 tar files.
Ok thank you I just restored. Is there any way to update from MF3?
jd1639 said:
That's your problem. You can't flash kernels on mf3. You'll probably have to odin the mf3 tar files.
Click to expand...
Click to collapse
ZOOPidy said:
Ok thank you I just restored. Is there any way to update from MF3?
Click to expand...
Click to collapse
There is the 4.3 MK2
When I go to system update in settings, it does not show any updates.
hednik said:
There is the 4.3 MK2
Click to expand...
Click to collapse
ZOOPidy said:
Ok thank you I just restored. Is there any way to update from MF3?
Click to expand...
Click to collapse
Follow my thread http://forum.xda-developers.com/showthread.php?t=2621279 get your reading mode on and let me know if u need more help. .....:thumbup: .... Goodluck. ...Also check this Index
http://forum.xda-developers.com/showthread.php?t=2616221..... anything that u should know for MK2 firmware that u about to install. .... ....Thanks to @guut13 putting it all together. .......:thumbup::thumbup:
Swyped from MK2 Dark Venomous X1