Database Users

[RECOVERY][CWM 5.5.0.4]LAVA Iris 504Q

Here is the CWM 5.5.0.4 for Lava Iris 504Q
Requirements:
1. Sp Flash Tool
2. Recovery.img
3. MT6589_Android_scatter_emmc.txt (only use this one. it is modified.)
Download: CWM 5.5.0.4 for Lava Iris 504Q
http://d-h.st/Zh4
Download: Sp Flash Tools For Mediatek phones
http://mtk2000.ucoz.ru/down7/FT3.13.04.rar
Download: MT6589_Android_scatter_emmc.txt
http://d-h.st/Paz
Instructions for flashing using SP Flash Tools:
1. Install drivers for your phone http://forum.xda-developers.com/attachment.php?attachmentid=2107980&d=1373524210
2. Copy recovery.img and scatter file in new same folder
3. Extract and open the SP Flash Tools.
4. In SP Flash Tools, click on Scatter-Loading and the program will ask you the location of the scatter loading file for your device select mt6589 scatter file.txt
5.Check only recovery.img, uncheck all others. (will be checked auto)
6. Switch off your phone (Remove the battery to make sure it is switched off).
7. Click the Download option (present on the right of Firmware
> Upgrade option) and the flash tool will start looking for your phone.
8. Put Battery and Connect usb to your phone now. The Flash Tool will start the flashing process, the progress of which can be viewed from a yellow progress bar at the bottom of the flash tool.
Warning 1 - Don't interrupt this process as it can potentially brick your device.
Warning 2 - Make sure no power interruption takes place. (Use a laptop to ensure this).
9. After the process completes, a green ring will appear on your device signalling that the process was successful.
10.Disconnect your phone.
Thats all
Press volume Up and Power same time to get in to CWM
IRIS 504Q DEVELOPMENT IS PROGRESSING FAST!!!!

fandroid7 said:
Here is the CWM 5.5.0.4 for Lava Iris 504Q
Requirements:
1. Sp Flash Tool
2. Recovery.img
3. MT6589_Android_scatter_emmc.txt (only use this one. it is modified.)
Download: CWM 5.5.0.4 for Lava Iris 504Q
http://d-h.st/Zh4
Download: Sp Flash Tools For Mediatek phones
http://mtk2000.ucoz.ru/down7/FT3.13.04.rar
Download: MT6589_Android_scatter_emmc.txt
http://d-h.st/Paz
Instructions for flashing using SP Flash Tools:
1. Install drivers for your phone http://forum.xda-developers.com/attachment.php?attachmentid=2107980&d=1373524210
2. Copy recovery.img and scatter file in new same folder
3. Extract and open the SP Flash Tools.
4. In SP Flash Tools, click on Scatter-Loading and the program will ask you the location of the scatter loading file for your device select mt6589 scatter file.txt
5.Check only recovery.img, uncheck all others. (will be checked auto)
6. Switch off your phone (Remove the battery to make sure it is switched off).
7. Click the Download option (present on the right of Firmware
> Upgrade option) and the flash tool will start looking for your phone.
8. Put Battery and Connect usb to your phone now. The Flash Tool will start the flashing process, the progress of which can be viewed from a yellow progress bar at the bottom of the flash tool.
Warning 1 - Don't interrupt this process as it can potentially brick your device.
Warning 2 - Make sure no power interruption takes place. (Use a laptop to ensure this).
9. After the process completes, a green ring will appear on your device signalling that the process was successful.
10.Disconnect your phone.
Thats all
Press volume Up and Power same time to get in to CWM
IRIS 504Q DEVELOPMENT IS PROGRESSING FAST!!!!
Click to expand...
Click to collapse
Nice Work Bro But I'm Using Canvas II
Sent from my Micromax A110 using xda premium

Help me out
unable to instal drivers for my lava iris 504q. I could not find the drivers in MT65xxusb driver. Could you please upload it. I flashed the stock ROM but was unable to flash the custom ROM. Now when I swtich on the device it's just showing lava, it is not getting into recovery mode either. Plz help me...
edit: succeeded in flash custom ROM

i need sptool rom for iris 504q my phone i bricked. plz help

thank you very much. but what the use if we dont have custom roms for our device

Pls Help!!
Using SP flash tool and the scatter file uploaded above, can we flash the entire rom?
I used to use a scatter file and flash the stock rom using sp tools in my previous phone, so just wanted to know will the same thing work with this scatter file??
Thanks

thanx
Sent from my A110Q using XDA Premium 4 mobile app

Lava iris 504q+
fandroid7 said:
Here is the CWM 5.5.0.4 for Lava Iris 504Q
Requirements:
1. Sp Flash Tool
2. Recovery.img
3. MT6589_Android_scatter_emmc.txt (only use this one. it is modified.)
Download: CWM 5.5.0.4 for Lava Iris 504Q
http://d-h.st/Zh4
Download: Sp Flash Tools For Mediatek phones
http://mtk2000.ucoz.ru/down7/FT3.13.04.rar
Download: MT6589_Android_scatter_emmc.txt
http://d-h.st/Paz
Instructions for flashing using SP Flash Tools:
1. Install drivers for your phone http://forum.xda-developers.com/attachment.php?attachmentid=2107980&d=1373524210
2. Copy recovery.img and scatter file in new same folder
3. Extract and open the SP Flash Tools.
4. In SP Flash Tools, click on Scatter-Loading and the program will ask you the location of the scatter loading file for your device select mt6589 scatter file.txt
5.Check only recovery.img, uncheck all others. (will be checked auto)
6. Switch off your phone (Remove the battery to make sure it is switched off).
7. Click the Download option (present on the right of Firmware
> Upgrade option) and the flash tool will start looking for your phone.
8. Put Battery and Connect usb to your phone now. The Flash Tool will start the flashing process, the progress of which can be viewed from a yellow progress bar at the bottom of the flash tool.
Warning 1 - Don't interrupt this process as it can potentially brick your device.
Warning 2 - Make sure no power interruption takes place. (Use a laptop to ensure this).
9. After the process completes, a green ring will appear on your device signalling that the process was successful.
10.Disconnect your phone.
Thats all
Press volume Up and Power same time to get in to CWM
IRIS 504Q DEVELOPMENT IS PROGRESSING FAST!!!!
Click to expand...
Click to collapse
any ROM development for Lava iris 504q+... Its got huge potential. Should be similar to 504q ROM. can i install cmw recovery image on 504q+ using mobileuncle ???

sagothic said:
any ROM development for Lava iris 504q+... Its got huge potential. Should be similar to 504q ROM. can i install cmw recovery image on 504q+ using mobileuncle ???
Click to expand...
Click to collapse
No don't flash this recovery as cwm is device specific.. one cwm is available for 504q+ bt I think 504q+ got kitkat update so it'll not work on new version.. so wait for the one [emoji6]

cwm for 504Q+
shaikhdjm said:
No don't flash this recovery as cwm is device specific.. one cwm is available for 504q+ bt I think 504q+ got kitkat update so it'll not work on new version.. so wait for the one [emoji6]
Click to expand...
Click to collapse
actually its not cwm but based on it
** you need rooted device to use mobile uncle tools
flash the image i provided with mobile uncle tools

Update.zip downloaded but not instaled
sophisticatedjoker said:
actually its not cwm but based on it
** you need rooted device to use mobile uncle tools
flash the image i provided with mobile uncle tools
Click to expand...
Click to collapse
My iris 504q+ got the OTA update for 4.4 but the problem is that only the Update.zip file has been downloaded and it doesn't get installed. Someone please help. My phone has been rooted using framaroot but i don't think that should create and problem right?
Awaiting response!
---------- Post added at 05:23 PM ---------- Previous post was at 05:17 PM ----------
sophisticatedjoker said:
actually its not cwm but based on it
** you need rooted device to use mobile uncle tools
flash the image i provided with mobile uncle tools
Click to expand...
Click to collapse
I rooted my iris 504q+ using framaroot and tried install cmw using mobileuncle. I think it never got installed however it did ask me once to reboot into recovery. Post that i haven't been able to boot into recovery. I think i have even lost my stock recovery image. Can i install stock update using cmw???
Please reply

sagothic said:
My iris 504q+ got the OTA update for 4.4 but the problem is that only the Update.zip file has been downloaded and it doesn't get installed. Someone please help. My phone has been rooted using framaroot but i don't think that should create and problem right?
Awaiting response!
---------- Post added at 05:23 PM ---------- Previous post was at 05:17 PM ----------
I rooted my iris 504q+ using framaroot and tried install cmw using mobileuncle. I think it never got installed however it did ask me once to reboot into recovery. Post that i haven't been able to boot into recovery. I think i have even lost my stock recovery image. Can i install stock update using cmw???
Please reply
Click to expand...
Click to collapse
Flash stock rom via sp flash tools, you will be able to get update and if ur recovery is bricked that too will come back [emoji6]

Clock work mode for lava iris406q
hello friend i m new at this forum i have lava iris406q , i m still google but there no way to get or installl qwm for my android phone please frnds help me ,
beacause i bricked my by device and by luck it was in under warranty.

cwm for iris406q
hello sir i m i want cwm for iris406q

Plzz help me..cwm/twrp recovery for lava iris 402..
Sent from my IRIS402 using xda app-developers app

hey cwm for x1 grand lava pls

How can i get it.

Tachileck

Equalizer

Hello. @fandroid7
I have a request for port cwm for Lava A68 and A51 (spreadtrum chipsets SC7731). I have stock recovery.img for both.
I tried but TWRP - no buttons and touch works, in MIUI recovery - all works but no one command like install zip, backup, restart, ect.
Can You port for Lava users of this models?
Regards
nalas

[Guide]How to flash cwm recovery on micromax canvas 2 coloars a120[4gb with kitkat ]

NOW YOU CAN FLASH CLOCK WORK MODE RECOVERY ON MICROMAX CANVAS2 COLORS 4GB VERSION WITH KITKAT ....TO FLASH CWM ..JUST FOLLOW THESE STEPS:
STEP1: DOWNLOAD THESE FILES
A) CWM FOR C2C (4GB KITKAT)
B) ALL IN ONE MTK DRIVER
C) SP FLASH TOOLS
STEP2:EXTRACT ALL THE ZIP FILES
STEP4: INSTALL VCOM DRIVER ON YOUR PC
STEP5: DOUBLE CLICK ON SP FLASH TOOLS AND BROWSE THE SCATTER FILE WHICH YOU HAVE FOUND IN CWM RECOVERY FOLDER AND CLICK ON DOWNLOAD
STEP6:SWITCHOFF AND REMOVE THE BATTERY FROM YOUR MOBILE AND CONNECT IT TO YOUR PC VIA DATA CABLE AND WAIT FOR THE COMPLETION OF THE PROCESS
STEP7.REMOVE THE DATA CABLE AND INSERT THE BATTERY AND PRESS VOLUME UP + VOLUME DOWN+ POWER ..NOW YOU WILL GET 2 OPTIONS Ie. Recovery mode:volume up and Factory Mode:Volume down......just press volume up to get into cwm recovery ...and now you can backup/restore or flash roms form this recovery....enjoy :good:
Warning :
Plz follow the above steps at your own risk.....I am not responsible for any damage you do to your device !!
(It works only with micromax canvas 2 colors a120 with kitkat(4gb) .....Do not try it with jellybean firmware ...)
MY WORKS :
HOW TO INCREASE APP STORAGE IN MMX C2C KK
Plz Hit thanks button if I helped you!

Thanks
Thanks for Sharing

srsbros said:
Thanks for Sharing
Click to expand...
Click to collapse
You're most welcome

working perfectly....... thank you........

How to root it (4gb kitkat update a120)
Sent from my Micromax A120 using XDA Premium 4 mobile app

How to increase app storage in mmx c2c Kitkat(FOTA)...?
Sent from my Micromax A120 using XDA Premium 4 mobile app

PLZ HELP
hello Biswajyoti.
i tried every thing as per your instructions. but i m stuck at the very last point. when i get options for Recovery Mode and Factory Reset , my phone always boots in normal mode. I press volume up key.. but it always starts rooting in normal mode only.. i never get into recovery mode. so cant load super user onto my phone...
Plz Help. What To Do..
Thanks in Advance.

PTM is changed for ROM, it must be downloaded
Biswajyoti said:
NOW YOU CAN FLASH CLOCK WORK MODE RECOVERY ON MICROMAX CANVAS2 COLORS 4GB VERSION WITH KITKAT ....TO FLASH CWM ..JUST FOLLOW THESE STEPS:
STEP1: DOWNLOAD THESE FILES
A) CWM FOR C2C (4GB KITKAT)
B) ALL IN ONE MTK DRIVER
C) SP FLASH TOOLS
STEP2:EXTRACT ALL THE ZIP FILES
STEP4: INSTALL VCOM DRIVER ON YOUR PC
STEP5: DOUBLE CLICK ON SP FLASH TOOLS AND BROWSE THE SCATTER FILE WHICH YOU HAVE FOUND IN CWM RECOVERY FOLDER AND CLICK ON DOWNLOAD
STEP6:SWITCHOFF AND REMOVE THE BATTERY FROM YOUR MOBILE AND CONNECT IT TO YOUR PC VIA DATA CABLE AND WAIT FOR THE COMPLETION OF THE PROCESS
STEP7.REMOVE THE DATA CABLE AND INSERT THE BATTERY AND PRESS VOLUME UP + VOLUME DOWN+ POWER ..NOW YOU WILL GET 2 OPTIONS Ie. Recovery mode:volume up and Factory Mode:Volume down......just press volume up to get into cwm recovery ...and now you can backup/restore or flash roms form this recovery....enjoy :good:
Warning :
Plz follow the above steps at your own risk.....I am not responsible for any damage you do to your device !!
(It works only with micromax canvas 2 colors a120 with kitkat(4gb) .....Do not try it with jellybean firmware ...)
MY WORKS :
HOW TO INCREASE APP STORAGE IN MMX C2C KK
Plz Hit thanks button if I helped you!
Click to expand...
Click to collapse
Some how i rooted micromax a120 (with 4.4.2), Now unable to install CWM :crying:
Tried a lot, Mobile uncle, 100's of SP tools and your guide also, it shows message like "PTM has changed for ROM, it must be downloaded". Any solutions plzz
and also your driver link is not working!

Not in Device Manager
Biswajyoti said:
STEP4: INSTALL VCOM DRIVER ON YOUR PC
Click to expand...
Click to collapse
It is not detecting my device in the Device Manager.
It is Canvas A120 8gb variant.
I'm using Windows 8.1.
Though it showing other HTC and Samsung Phones.
Here's the link to the image:
1drv.ms/1Bz05Ny
Couldn't post the image or as hyper link because I've still not posted 10 posts.

naveen anand said:
hello Biswajyoti.
i tried every thing as per your instructions. but i m stuck at the very last point. when i get options for Recovery Mode and Factory Reset , my phone always boots in normal mode. I press volume up key.. but it always starts rooting in normal mode only.. i never get into recovery mode. so cant load super user onto my phone...
Plz Help. What To Do..
Thanks in Advance.
Click to expand...
Click to collapse
Just use Kingo Root, connect ur phone to it and root.
And one more thing, I don't work for them. It is just how I rooted mine.

Install recovery on rooted by king root
Rishabh Dhiman said:
Just use Kingo Root, connect ur phone to it and root.
And one more thing, I don't work for them. It is just how I rooted mine.
Click to expand...
Click to collapse
bro i had rooted my phone by king root should i install recovery for it.
Kitkat fota a120

Is there any way to root & intall cwm in micromax canvas 2 a120 8 gb model...
Is the roms for 4 gb model works with 8 gb variant...
Edit: finally managed to get the root

TUTORIAL HD, USE OP files for your phone, files in THE VIDEO are for WIKO RAINBOW KITKAT BASE V10:

Biswajyoti said:
NOW YOU CAN FLASH CLOCK WORK MODE RECOVERY ON MICROMAX CANVAS2 COLORS 4GB VERSION WITH KITKAT ....TO FLASH CWM ..JUST FOLLOW THESE STEPS:
STEP1: DOWNLOAD THESE FILES
A) CWM FOR C2C (4GB KITKAT)
B) ALL IN ONE MTK DRIVER
C) SP FLASH TOOLS
STEP2:EXTRACT ALL THE ZIP FILES
STEP4: INSTALL VCOM DRIVER ON YOUR PC
STEP5: DOUBLE CLICK ON SP FLASH TOOLS AND BROWSE THE SCATTER FILE WHICH YOU HAVE FOUND IN CWM RECOVERY FOLDER AND CLICK ON DOWNLOAD
STEP6:SWITCHOFF AND REMOVE THE BATTERY FROM YOUR MOBILE AND CONNECT IT TO YOUR PC VIA DATA CABLE AND WAIT FOR THE COMPLETION OF THE PROCESS
STEP7.REMOVE THE DATA CABLE AND INSERT THE BATTERY AND PRESS VOLUME UP + VOLUME DOWN+ POWER ..NOW YOU WILL GET 2 OPTIONS Ie. Recovery mode:volume up and Factory Mode:Volume down......just press volume up to get into cwm recovery ...and now you can backup/restore or flash roms form this recovery....enjoy :good:
Warning :
Plz follow the above steps at your own risk.....I am not responsible for any damage you do to your device !!
(It works only with micromax canvas 2 colors a120 with kitkat(4gb) .....Do not try it with jellybean firmware ...)
MY WORKS :
HOW TO INCREASE APP STORAGE IN MMX C2C KK
Plz Hit thanks button if I helped you!
Click to expand...
Click to collapse
Hi my phone is not getting recognise, and download of recovery is not working in SP splash tool, but phone is getting recognised in device manager..Please help me I really need to the phone to get rooted

sandeeptengale said:
Hi my phone is not getting recognise, and download of recovery is not working in SP splash tool, but phone is getting recognised in device manager..Please help me I really need to the phone to get rooted
Click to expand...
Click to collapse
Use Kingo Root, that WILL work as long as the USB Cable is not faulty.

sandeeptengale said:
Hi my phone is not getting recognise, and download of recovery is not working in SP splash tool, but phone is getting recognised in device manager..Please help me I really need to the phone to get rooted
Click to expand...
Click to collapse
plz install mtk driver from device manager (right click>update driver>browser the folder)

Same is the case here....but i am using unite....what to do?
Sent from my Micromax A106 using XDA Free mobile app

[HOWTO] Flash TWRP and Flash CM+GApps [Meizu M2 Note]

Hi to everybody
I'm doing this thread because I've seen that there's a lot of confussion about how to install all this things properly, and I think that concentrating the wide-spread information could help you to get rid of this. First of all I have to thanks @aaawqw and @Moyster for their great efforts.
This is going to be a recopilatory of several sources and personal tips to help you to do this the easiest way. I'm not responsible of bricked phones nor your personal problems.
Please, read the full tutorial before doing anything, to avoid bricks and those things.
PREPARE THE RECIPE
Download these files:
- Unlocking bootloader tool: HERE
- TWRP image from Moyster (creator of LOS14 for our device): here
- If you want to install a modified version of FlymeOS, use this one from Romul35 from 4PDA: here. Original post
- Last LineageOS 14 build: from this thread. PLEASE DON'T FORGET TO THANK THE DEVELOPERS
- GApps: here I recommend the nano option. Choose ARM64 and Android version 6.0.
Put those three last files into your internal memory. If you've got an microSD card, I recommend you to put them into it (it's safer and easier).
UNLOCKING THE BOOTLOADER
To unlock the bootloader go to:
- Kevin.MX @aaawqw) post: here
Finally we have a guide to unlock the bootloader of Meizu m2 note. We need Mediatek SP Flash Tool, MTK phone drivers and the images/bin files for unlocking. No modaco superboot, no fake tutorials any more
Now here's the guide:
1. Download the files I provide
Then unzip it. You'll get a folder with FlashTool, Phone drivers and unlock images.
2.Install drivers for Mediatek platform.
3.Flash the temp-unlock-secro.img via Flashtool. (secro row)
4.Flash secro.img, lk.bin, preloader_meizu6753_65c_l1.bin via Flashtool. (secro, lk and preloader rows respectively)
5.Disconnect USB data cable and power on the phone. If you see the "=>Normal boot" sign(it's quite small.......) in the left bottom cornor of the screen, then the unlock is done. You can now flash things in whatever way you like. The guide is over~~~
The full tutorial is here
The unlock tool is here
Thank you for testing&trying!
If you've seen this spoiler and didn't thank Kevin, please go to here and thank him. This motivates him and gives him the recognisement he deserves.
- Robot Hijau 97 Youtube video: here It isn't in English, but may help if you find any problem or get lost during the unlocking. Leave him a like if it helped you.
This unlocking guide only works for M571 model. If you try this with a M571C (China Telecom) model, you'll get a bricked phone (very useful if you like paperweights )
THIS METHOD DOES WORK FOR M571H MODEL. DON'T WORRY, THE ONLY ONE THAT GIVES SOME ISSUES IS THE M571C.
The great user @aaawqw states "And Meizu M571C should use the same method of meizu m2 (mini), a shell script for frp unlock. But no recovery images yet…Different hardware and partitions"
Tips to unlock the bootloader easily:
- If you're going to do it from a Windows 10 or 8 pc, have in mind that to install unsigned drivers you'll have to unlock the feature in your pc. A guide to do this: here
- Select the images to flash and hit the Download button before connecting your Meizu (pressing Vol Down button). This will help you if it turns on and off and makes the flashing impossible.
- Download the guide or see the video to correctly follow all the steps. You don't want to lose your phone, don't you? Don't try to mix guides, because you may skip a step and brick your phone. The video and Kevin.MX guide are the same procedure, they both are safe.
INSTALLING TWRP
Once done this part, we'll proceed with the installation of TWRP recovery image. There are two ways, choose the easier to you:
- Flash TWRP from SP Flashtool (original idea from @widagdag. The post: here)
+Turn off your device
+ By using your pc or laptop, extract the TWRP zip for meizu m2 note, there's a file "recovery.img"
+ You can flash it via SP flash tool (clicking the recovery, then select the file)... then click Download, wait until finished!! (Check symbol)
+ You can reboot ur device now, unlocked bootloader and installed twrp!
*The profit is u didn't need to root first and install any flash tool such as Rash, FlashFire, Flashify, etc. saving you some time
Click to expand...
Click to collapse
- Flash the recovery image from Flyme:
+ Get root access (if you do, skip this step). You can get it downloading Kingroot: here. Just install this apk and follow the steps
+ Unzip TWRP zip into a known folder
+ Download Flashify from the Playstore
+ Grant superuser access
+ (Optional) make a backup of your current recovery going to backup tab
+ Tap Recovery Image
+ Choose a file
+ Find TWRP img that you unzipped before and flash it
Click to expand...
Click to collapse
INSTALLING CM AND GAPPS
We're close to the end of this post. The final step: installing your desired ROM and GApps. I will flash CM from the thread whose link is at the download section.
I hope you've put it into your memory (internal/external) as we said
Ok so:
- Turn off your phone
- Go into the TWRP recovery (Vol up+power)
- (Optional but recommended) Make a backup of Flyme, just in case you don't like the new ROM and would like to go back to Flyme. If it takes up too much memory, move it to your pc after making the backup.
- Go to Wipe menu
- Go to advanced wipe
- Select these:
+ System
+ Cache
+ Dalvik Cache
+ Data
- Swipe to do the wipe
- Go to install.
- Select your zip image (in my case the cm13 I downloaded).
- Install also the GApps zip file you downloaded
- Restart to System, and check what you've done.
Some final tips:
- Make the backup, seriously, it takes 10 min and you'll have a Flyme backup if you don't like CM.
- If you want to transfer all your apps and their data from Flyme to your new ROM, use Titanium Backup.
- If you want to install Xposed Framework, it's the same procedure: enter into TWRP, tap install, select the zip and swipe.
- This won't delete your images or videos, but I would recommend to transfer them to a microSD card or your PC.
- Yes, you need to do all this to install a custom ROM. Yes, even unlocking the bootloader. Don't try to skip a step if you aren't sure about what you're doing.
I think that's all, I'll update this post if I lost anything.
I hope this helped you to move into CM world. If you have any doubt don't hesitate to ask.
I know this seems exhausting, but trust me, it worths it. Welcome to the custom ROMs world in your Meizu M2 Note. Let the magic begin.
ADDITIONAL GUIDES
RELOCKING THE BOOTLOADER
If you want to relock the bootloader just follow this simple steps:
Flash the original recovery image from Flashtool of from Flashify (the steps are the same as installing TWRP). You can find this image here
From there, install an update.zip (download them from the official flyme web: here and put it into the storage )
Now you have flyme again with a locked bootloader.
INSTALLING FLYME WITH TWRP
It's very important that you don't install an update.zip from the original Flyme page, because you will cause a bootloop. To get the flyme updates, you can follow one of these two methods:
METHOD 1: 4PDA
-Download the modified zips from 4PDA: here]. Translate it to English. It's on custom firmware>Flyme
-Flash them from TWRP
METHOD 2: DO IT YOURSELF
-Download the update.zip file from the Flyme page
-Open it and remove the preloader- files
-Flash it from TWRP. It will give you an error: IGNORE IT.
Reboot and done, you've got Flyme and TWRP.
UNBRICK A PAPERWEIGHT
BIG THANKS TO @numpea FOR THIS:
This just a firmware that has all the partitions and can be used to unbrick to device using SPFlashtool
Here is the link:
FIRMWARE
- Flash temp_unlock_secro.img with sp flashtool like you do when unlocking the bootloader.
- When done, disconnect the device and add the firmware to sp flashtool. You need to select "format all+download", click on "Download" and connect the device. The flashing process will start. After it finishes, the device will start again.
You wil notice that you lost your imei number you can add it back by:
Using MTK Engineering Mode (does not requires root)
Open engineering mode » Click on Engineer Mode (MTK) » Swipe left to Connectivity » click on CDS Information » Radio Information
Click on phone 1 if you want to change your sim 1 or choose Phone 2 to change sim 2 IMEI, follow this guide:
For Phone 1: “AT+ EGMR=1,7,”YOUR NEW IMEI NO” (make sure you add a space in between AT+ & EGMR)
For Phone 2: “AT+ EGMR=1,10,”YOUR NEW IMEI NO” (make sure you add a space in between AT+ & EGMR)
Using Chamelephon (requires root, but much more easier)
Just copy the IMEIS from the phone's box and put them into the app.
hope this is helpful
Click to expand...
Click to collapse
I'll keep updating the info!

Really complete, I could unlock my M2 Note and install CM-12.1 ! Thanks !

Moyster said:
Really complete, I could unlock my M2 Note and install CM-12.1 ! Thanks !
Click to expand...
Click to collapse
Moyster xDD :laugh::laugh: Thanks to you, without you this wouldn't have been possible

Pretty much covered all, just state the Armv7 Android level API 21 64bit, 5.1 Micro or Nano for gapps. They might get confused on what to choose.

Xtian Rey said:
Pretty much covered all, just state the Armv7 Android level API 21 64bit, 5.1 Micro or Nano for gapps. They might get confused on what to choose.
Click to expand...
Click to collapse
Very true, thanks a lot. I introduced the platform and the Android version of GApps

Thanks nice guide... Very useful for everyone who want play and modified the M2 note.

"This unlocking guide only works for M571 model. If you try this with a M571C (China Telecom) model, you'll get a bricked phone (very useful if you like paperweights*)"
I Am Using M571C, But Everything Fine.
Sent from my M2 Note using XDA Forums Pro.

Mr0oHo0 said:
"This unlocking guide only works for M571 model. If you try this with a M571C (China Telecom) model, you'll get a bricked phone (very useful if you like paperweights*)"
I Am Using M571C, But Everything Fine.
Sent from my M2 Note using XDA Forums Pro.
Click to expand...
Click to collapse
I include this on the guide. I read it bricked the phone in several cases, but I'm glad yours didn't.

Thanks for your guideline , it helps a lot !

Great work lol
Another thing is…ShevT's recovery has no problem in cache partition.Only my broken recovery did… So remove the cache fixing partAny problem just send me a private message. I'll check when i have time.
---------- Post added at 04:00 PM ---------- Previous post was at 03:58 PM ----------
And Meizu M571C should use the same method of meizu m2 (mini), a shell script for frp unlock. But no recovery images yet…Different hardware and partitions…
Another thing is, Kingroot is not suggested. It cannot be detected by Flashfire and some other tools. And cannot be replaced by SuperSU. So Kingo Root+SuperSU might be better.

aaawqw said:
Great work lol
Another thing is…ShevT's recovery has no problem in cache partition.Only my broken recovery did… So remove the cache fixing partAny problem just send me a private message. I'll check when i have time.
---------- Post added at 04:00 PM ---------- Previous post was at 03:58 PM ----------
And Meizu M571C shoukd use the same method of meizu m2 (mini), a shell script for frp unlock. But no recovery images yet…Different hardware and partitions…
Click to expand...
Click to collapse
https://github.com/Moyster/android_device_meizu_m2note/blob/cm-12.1/BoardConfig.mk#L10
Line 10 to 15 you have the partitions size
Code:
$ cat /proc/partinfo
example :
Name------------Start-------------Size
recovery 0x0000000004840000 0x0000000001400000
Take the Size value : "0x0000000001400000" => hexadecimal to decimal => 20971520 = recovery partition size
PS: I don't think the hardware is "that" different, at least, the kernel meizu released should contain both phone models/drivers

This unlocking guide only works for M571 model.
Click to expand...
Click to collapse
Mine is M571H, can I proceed?

Qeemi said:
This unlocking guide only works for M571 model.
Mine is M571H, can I proceed?
Click to expand...
Click to collapse
Mine too and it worked. I can't assure you anything, but I think that the problem are m571C which are different. Good luck if you're going to give it a try!

Moyster said:
https://github.com/Moyster/android_device_meizu_m2note/blob/cm-12.1/BoardConfig.mk#L10
Line 10 to 15 you have the partitions size
Code:
$ cat /proc/partinfo
example :
Name------------Start-------------Size
recovery 0x0000000004840000 0x0000000001400000
Take the Size value : "0x0000000001400000" => hexadecimal to decimal => 20971520 = recovery partition size
PS: I don't think the hardware is "that" different, at least, the kernel meizu released should contain both phone models/drivers
Click to expand...
Click to collapse
See it. I'll give a try on m2 note(M571C, China Telecom). At least try to build twrp But seems my pc's hdd is not enough No space for source code

little problems.
bootloader unlocking and twrp and roms works very well..
1. OTG is working for me.. :good:
2. unfortunately my phone is not detected by PC..
(show USB is not connected, USB debugging is not accessible..)
3. little bit lag here and there..
4. wifi works well :good:
Need more optimization.. Expecting lot more from you
thankyou very much for this :good:
DOUBT : so bootloader is unlocked, now it is possible to make good MM and N based CM roms ?

dinkan01 said:
bootloader unlocking and twrp and roms works very well..
1. OTG is working for me.. :good:
2. unfortunately my phone is not detected by PC..
(show USB is not connected, USB debugging is not accessible..)
3. little bit lag here and there..
4. wifi works well :good:
Need more optimization.. Expecting lot more from you
thankyou very much for this :good:
DOUBT : so bootloader is unlocked, now it is possible to make good MM and N based CM roms ?
Click to expand...
Click to collapse
hi,which build of cm 12 you put in phone?

M571U
I have the Meizu M571U Model. Can I do this or will it be bricked?
Thank you very much

venturaj said:
I have the Meizu M571U Model. Can I do this or will it be bricked?
Thank you very much
Click to expand...
Click to collapse
It won't, the only problematic model is the M571C, have fun

LBA97 said:
It won't, the only problematic model is the M571C, have fun
Click to expand...
Click to collapse
How can I check which model my m2 note is..?

[email protected] said:
How can I check which model my m2 note is..?
Click to expand...
Click to collapse
Check the store page you bought it from. If you bought it from China, then probably it's a M571C. Good luck

twrp Porter/Maker for Mediatek MT67XX 64bit & new 32bit Phone

twrp Porter-
as we know there is no tool available to port twrp for mt67XX. Phone so here i create a Simple and user friendly tool to Manually Port twrp for the Mediatek MT67XX Phone also Work with MT65XX new 32 bit phone .
The tool is Not based on Source This is a manually Porting Method where we use Stock Recovery to Port a custom Recovery. i have Port twrp for almost all latest MT67XX Chip from source and you can use as a Port Recovery,[Link below]..
What you need
1. tool Download Here https://androidfilehost.com/?fid=962021903579481564
2. Stock recovery [dump using SP tool or using Miracle box] Rename it 'stock.img'
3. Ported twrp from same chip [ Here is My collection- https://www.androidfilehost.com/?w=files&flid=220042] select according your chip if not work try from other phone. rename it 'port.img'
Note- i have Not enable auto copy to keep work with all chip Manually copy Paste Require.
Instructions-
Place port.img and stock.img in tool folder
Run twrp Kitchen.exe and follow on screen instructions
Donation-
You can Donate Me http://paypal.me/droiddeveloper
Faq-
1. Touch Not Work-
it's due to kernel source try to port from other twrp,
final solution use OTG or compile from source.
2. unable to mount partition's-
check and fix fastab in ramdisk folder before hiting enter.
3,. is this Work on old MT65XX Phone-
yes you can use it for MT65XX phone.
4. is This Method work 100% on all Phone-
No it can't work 100% on all phone but work on up to 90% of Mediatek Phone.
5. is this Support Nougat and oreo Images-
yes this one Support oreo and Nougat Recovery Images.
XDA:DevDB Information
twrp porter , Tool/Utility for all devices (see above for details)
Contributors
XN Logos
Version Information
Status: Beta
Current Beta Version: 1.0
Beta Release Date: 2017-09-30
Created 2017-10-01
Last Updated 2018-01-06

@XN Logos
Thanks for the tool.
I cannot download the recovery
MT6757 6.0 MM.rar
MT6757 Nougat helio P25 6GB RAM.zip
MT6797 Helio X27 6.0MM.rar

you can download from androidfilhost.
here is twrp for ulefone t1 ported using this tool base umi plus e. Helio p25, this tool not work on umidigi crystal 4GB/64GB i have tried but not success. https://androidfilehost.com/?fid=673368273298987398

Thank u for your great job, i think the recovery we obtain is called "image-new.img" (and not "recovery-new.img" as it's mentioned in the screen instruction). I successfully get this recovery but don't know how to flash it ( because my phone is locked and not rooted "LENOVO C2- k10a40-" ( MT6735 ). HELP PLZ and thanks again .

walid77dz said:
Thank u for your great job, i think the recovery we obtain is called "image-new.img" (and not "recovery-new.img" as it's mentioned in the screen instruction). I successfully get this recovery but don't know how to flash it ( because my phone is locked and not rooted "LENOVO C2- k10a40-" ( MT6735 ). HELP PLZ and thanks again .
Click to expand...
Click to collapse
You can flash it using SP flash tools, take scatter file from your ROM and then flash with SP tools...
Here is Fastboot Guide, but you can face adbd and large image error with fastboot.
Code:
fastboot oem unlock
fastboot flash recovery recovery-new.img

Please, help me to find usb vcom drivers for my device : LENOVO C2, k10a40, MT6735. Thank u again

walid77dz said:
Please, help me to find usb vcom drivers for my device : LENOVO C2, k10a40, MT6735. Thank u again
Click to expand...
Click to collapse
I beleive that any question not related to TWRP porter is OT here. Check driver v. 5.1632.
mod edit - needrom links removed not allowed due to registration required in order to download

Here is all Flash tools and drivers-
https://androidfilehost.com/?w=files&flid=216849

XN Logos said:
Here is all Flash tools and drivers-
https://androidfilehost.com/?w=files&flid=216849
Click to expand...
Click to collapse
You can get all news about Mediatek driver and tools (like Flashtool) here:
http://www.androidiani.com/forum/mo...l-flash-di-telefoni-con-chipset-mediatek.html
The latest driver (ADB + Preloader) is 5.1632 (the link that I posted), and is good fro XP up to Windows 10 and didn't rqeuire to disable driver sign.
The latest version for Flashtool (for Windows and Linux) is 5.1728
In the link that I posted are available Gogle Platform Tools (adb.exe/fastboot.exe) usefull for flash boot or recovery without using Flashtool.

base added for Helio X23 [Rename rk.bak to recovery.img]
https://androidfilehost.com/?fid=745849072291678959

Hi
great tool for mtk user y have à mt6797M ( elephone s7 4G )
if I understand correctly I need the recovery stock (I have) and a port recovery ( don't have ) but there are none in the link you give., I tried with MT6797 + helio + x25 + 6.0 but I have a MT6797M with android 7, I'm not sure try to flash .
is it possible for you to make a port of the MT6797M Helio X20 M ?
And my fil name: image-new.img not recovery-new.img it's normal ?

Thinking i got same request as Bradco but MT6753M chip Cubot Cheetah 2
I was not able to find the "1st kernel file", guessing it is xx.img-zImage file.
Here my device nougat stock recovery (or at page 4 device review)
With my device at the moment TWRP seems to work only on Marshmallow. It would be nice if someone like to share an updated recovery
BTW
It took me a few retries to check extracting recoveries requiers 3 or 4 times press enter instead of just a singel press any key

@toBsucht Psp @Bradco we have twrp for both Phone 1. Elephone S7 and 2.cubot cheetah 2 no need to Port again. search Forum..

XN Logos said:
@toBsucht Psp @Bradco we have twrp for both Phone 1. Elephone S7 and 2.cubot cheetah 2 no need to Port again. search Forum..
Click to expand...
Click to collapse
yes there is this twrp: TWRP 3.0.3 by Jemmini (I have it) available on needrom and xda
it works with android 6 without problem but not with android 7.
This TWRP 3.0.3 by Jemmini is based on rom: S7_4g_20170110092009_v1.9.zip which is a rom android 6: https://bbs.elephone.hk/thread-12895-1-1.html#.WdiBplu0OM
My rom got this one: s7_4g_20170814163417_v2.4.zip which android 7 v2.4
I tried this :
1. clean install the rom: s7_4g_20170814163417_v2.4.zip
2. start the phone
3. flash the twrp : TWRP_303_Elephone_S7_4g_v1.9
4. reboot the phone but it is blocking on the logo ( I access the recovery but can not start the phone )
5. y tried 2/3 times but once the recovery install it remains on the logo.
after searching I found only this recovery TWRP_303_Elephone_S7_4g_v1.9
I do not know if there is an update because all DROPbox links are down.

@Bradco
Please read carefully the object of this thread. It's only about TWRP porter.
Is not a thread of support for mod recovery about specific devices.
For this please post in the specific thread for the device. Thanks.
@XN Logos
I propose to add this as first object of firs post
- Scope of this thread
Scope of this thread is only to discuss about TWRP porter application.
Please don't discuss about support for recovery for specific devices.
For this please post in the specific thread for the devices.

bovirus said:
@Bradco
Please read carefully the object of this thread. It's only about TWRP porter.
Is not a thread of support for mod recovery about specific devices.
For this please post in the specific thread for the device. Thanks.
@XN Logos
I propose to add this as first object of firs post
- Scope of this thread
Scope of this thread is only to discuss about TWRP porter application.
Please don't discuss about support for recovery for specific devices.
For this please post in the specific thread for the devices.
Click to expand...
Click to collapse
yes sorry,
I explain just my situation, the subject of my post is well on the port of TWRP for processor MT6797M and not on elephone s7. I must speak well of the phone to explain the problem correctly.
Ps : y test this tuto : https://forum.xda-developers.com/showthread.php?p=32965365#post32965365
but y don't find the file BoardConfig.mk

Pretty much same here!
i took a look to default.prop it use a string:
ro.build.version.sdk=24 (stock v14 recovery)
ro.build.version.sdk=23 ( twrp recovery)
even more that needs to be updated in default.prop file from old TWRP to enable it on API24 i.g.
ro.build.fingerprint (seems to be a littel more work)
i stopped repacking TWRP since i note bad image maybe brick my phone.
Also someone told me marshmallow uses ID_creation code = MOB30J; Nougat uses ID_creation code = NHG47N .... idk
funny i removed a additioinal password request. Another user now got additional :highfive: and idk how it occur

Yes Guys, This thread is only for tool Not for Specific Device. So you can ask only for Port base [MT67XX] not for twrp. if you need twrp You can contact Me or create yourself using tool.

XN Logos said:
Yes Guys, This thread is only for tool Not for Specific Device. So you can ask only for Port base [MT67XX] not for twrp. if you need twrp You can contact Me or create yourself using tool.
Click to expand...
Click to collapse
ok I understand, I want to try to do it myself, can you make a port of MTK 6797M ?
( this is what I needed at the start, I came on this thread to do the twrp myself.
thank you in advance

As already written it is not that easy to use if some errors occur. Also i did not 100% on it which files i have to remove if tool say "delete following":
1. kernel (is it x.img-zImage?)
2. kernel offset (i guess i found)
and that flase "press ANY key" message! Just as a little sidenote for your update.

ZTE Blade A2 Plus Rooting( SuperSU or Magisk),Recovery & Flashing Stock Rom

Hi there, good to see you.
After struggling to find any helpful information about rooting ZTE Blade A2 plus, I finally was able to root>soft brick>hard brick>stock flash>repeat this beautiful device. So thought to share it here so that it becomes helpful for someone in need.
Device Information: https://forum.xda-developers.com/ge...te-blade-a2-plus-5-5-fhd-mt6750t-3gb-t3480759
Prerequisite: Winrar Latest version, VCOM and device drivers (MT67xx), General intelligence to download the attachments and to arrange everything in order and you're good to go
Step 1: Install custom recovery (We'll install TWRP)
a} Download recovery and preloader
b} Download Scatter file
c} Download SP Flash tools
d} Only tick recovery and preloader and select the downloaded files and flash it
e} When the process finishes and SP flash tools displays done, remove the phone and press "Vol Up+Power" to boot into recovery. It may ask you to make /system writable if you want swipe as indicated
f} Done enjoy
Note: Take this opportuniy to first of all backup your stock rom using TWRP and save it elsewhere.
Step 2: Rooting (With Magisk Or Super SU)
a} Download Magisk or Super SU flashable zip as per your need
Note: Magisk gives most of the Super SU features and doesn't trips google security net so you are able to use banking apps while rooted with magisk
b} Place downloaded zip in your sd card
c} Boot into TWRP recovery and flash the said zip
d} Done enjoy
Step 3: Flashing stock rom (Only russian version as of now)-Language is english bloatwares are Russian
a} Download Stock Rom from https://yadi.sk/d/RZLBrKKv3LxejN
Note: It contains PC Flashable stock rom along with scatter files and NVRAM backups so it'll help if you lose IMEI during the process, it is advisable to keep this offline as backup in case links stops working.
b} Flash the downloaded stock rom with SP flash tools
Note: This stock rom doesn't support VOLTE so i advice you to first take a full backup of your initial rom after installing TWRP, also please share that backup here as well so as i could add it to this thread to make it helpful for someone who has already lost VOLTE inclusing me
Conclusion: I'll be very happy if this information proves useful to you in any manner and also request you to must share your backup for me to get VOLTE back.
Thank You

MIUI 9 For A610 Plus
Preview:
Many many thanks Alfonso for making this vary valuable post . I think A2 Plus and A610 Plus are almost same , so kindly check this ROM me and may solve your volte problem
ww.getdroidtips.com/miui-9-zte-blade-a610-plus/[/url]

Rajevpmavoor said:
Preview:
Many many thanks Alfonso for making this vary valuable post . I think A2 Plus and A610 Plus are almost same , so kindly check this ROM me and may solve your volte problem
ww.getdroidtips.com/miui-9-zte-blade-a610-plus/[/url]
Click to expand...
Click to collapse
Although the rom is bugless but, unfortunately VOLTE didn't work.

MIUI 9 For A610 Plus
Did you flash this new MIUI 9 ROM , I think it has volte and it is in Android M.

Alfonso Osnofla said:
Although the rom is bugless but, unfortunately VOLTE didn't work.
Click to expand...
Click to collapse
does it boot into meta mode on pressing volume down+power button??( bcoz my fone boots into meta mode on doing so)
and how to go into bootloader?
while using sp flash tool i power off the fone and then connect it to sp flash tool via usb cable ...fone gets detected and but download for twrp doesnt occur ..it says PMT changed for the rom, select format all+ download ....
but i didnt do format all coz i dont have flashable stock rom...

I lost my IMEI after flash ROM, not able to retrieve IMEI

Issue in camera & Finger Lock
Alfonso Osnofla said:
Although the rom is bugless but, unfortunately VOLTE didn't work.
Click to expand...
Click to collapse
I have checked both ROM, Miui ROM camera is look like .02MB, No VOLTE, Finger Print lock is not working

Thanks. I have messed up anyway...
Anybody have a complete Readback (Using SP-Flash Tools) copy of (volte) rom?
I lost Imei, From the given NVram.bin, Could not edit Imei using BPGL.... pull as Maui Meta and SN writer can not do this with present update.
I need to revert back. please help with ROM copy and NVRAM Edit.

Alfonso Osnofla said:
Hi there, good to see you.
After struggling to find any helpful information about rooting ZTE Blade A2 plus, I finally was able to root>soft brick>hard brick>stock flash>repeat this beautiful device. So thought to share it here so that it becomes helpful for someone in need.
Device Information: https://forum.xda-developers.com/ge...te-blade-a2-plus-5-5-fhd-mt6750t-3gb-t3480759
Prerequisite: Winrar Latest version, VCOM and device drivers (MT67xx), General intelligence to download the attachments and to arrange everything in order and you're good to go
Step 1: Install custom recovery (We'll install TWRP)
a} Download recovery and preloader
b} Download Scatter file
c} Download SP Flash tools
d} Only tick recovery and preloader and select the downloaded files and flash it
e} When the process finishes and SP flash tools displays done, remove the phone and press "Vol Up+Power" to boot into recovery. It may ask you to make /system writable if you want swipe as indicated
f} Done enjoy
Note: Take this opportuniy to first of all backup your stock rom using TWRP and save it elsewhere.
Step 2: Rooting (With Magisk Or Super SU)
a} Download Magisk or Super SU flashable zip as per your need
Note: Magisk gives most of the Super SU features and doesn't trips google security net so you are able to use banking apps while rooted with magisk
b} Place downloaded zip in your sd card
c} Boot into TWRP recovery and flash the said zip
d} Done enjoy
Step 3: Flashing stock rom (Only russian version as of now)-Language is english bloatwares are Russian
a} Download Stock Rom from https://yadi.sk/d/RZLBrKKv3LxejN
Note: It contains PC Flashable stock rom along with scatter files and NVRAM backups so it'll help if you lose IMEI during the process, it is advisable to keep this offline as backup in case links stops working.
b} Flash the downloaded stock rom with SP flash tools
Note: This stock rom doesn't support VOLTE so i advice you to first take a full backup of your initial rom after installing TWRP, also please share that backup here as well so as i could add it to this thread to make it helpful for someone who has already lost VOLTE inclusing me
Conclusion: I'll be very happy if this information proves useful to you in any manner and also request you to must share your backup for me to get VOLTE back.
Thank You
Click to expand...
Click to collapse
Just try http://www.ztedevice.com/support/detail?id=FE22BEF5C33D4A17BCDA20AAE2631951 ( http://download.ztedevice.com/support/product/569/201802111051594/sd/20180211105554767.zip )
sd card update using twrp.
But first remove the first line from update script file located inside the zip.
Just reply.

Need MIUI rom
Heyy plz gime me teh rom for zte blade A2 plus i really need a miui rom for zte blade A2 plus...

Help I'm confused.
Reading the comments i got to know that many people lost their IMEI and VOLTE , I want to root the device So can anyone tell me when does this problem occur (loosing volte and imei) during rooting or while flashing a custom rom?

kingksath said:
I lost my IMEI after flash ROM, not able to retrieve IMEI
Click to expand...
Click to collapse
Did you loose your IMEI on rooting or while flashing any custom Rom?

http://www.mediafire.com/file/6768c1x7dqyd818/update.zip
version 4 sd card update

vasilemk said:
http://www.mediafire.com/file/6768c1x7dqyd818/update.zip
version 4 sd card update
Click to expand...
Click to collapse
What is it for?
Is it for volte?

vasilemk said:
http://www.mediafire.com/file/6768c1x7dqyd818/update.zip
version 4 sd card update
Click to expand...
Click to collapse
Is this an update to the Stock Rom?

hi, can u help me please, iam tryin to update with twrp , i did remove first line from script but i have error.

Found a way to unlock bands on MTK based phones by flashing basebands from phones with the same chipset. Doing this by using SPFLASH and flashing md1 files. Still unable to connect to cell network on my Doogee bl12000. Flashed this phones MD1, was wondering if anybody could provide me with the nvdata and nvram from the ZTE blase a2 plus. Hoping by flashing those files can connect to a U.S. network.