Help me, please!
Yesterday, I wanted to make a clean install for the latest Quarx's CM 10.1 nightly (I've been flashing Quarx's builds for almost a year now, he's The Best), but I think I made a terrible mistake.
When I wanted to make a factory reset, I've got this error because the sd-ext, I understand, that happened because TWRP's structure with almost all devices running Android 4.2.2 have a virtual-sd and a sd-ext, so I decided to make an Advance wipe and I every damn box, even wipe system and wipe sd card.
Finally when I rebooted my phone, TWRP asked to install SU, I pressed yes.
Then when my phone was rebooting, I've got this error:
Bootloader
09.10
Err:A5,70,39,00,27
So, I've been flashing Froyo's .sbfs since yesterday, when I get pass verification from RSDLite and rebooted the phone, it just keep bootlooping, I left it almost 15 minutes and still in Froyo's bootanimation, I know it has to do because it's needed wipe data and cahe, but I can't do that because I can't access stock recovery (volume down+power button), I just get the triangle with the little Android in it.
Here's is the .sbf
JORLA_U3_3.4.2_108-5_SIGNED_USAJORDMR1B25CLALALA022.0R_JORLAFROCLALALA_P027_A018_M016_HWp3_WIG147154_Service1FF.sbf.gz
And I did it with RSDLite 5.6.
Hope you can help me, thanks anyway.
On Stock Recovery press Vol-up+down buttons... Rooting & flashing custom roms & don't know how to enter stock recovery?
turffe said:
On Stock Recovery press Vol-up+down buttons... Rooting & flashing custom roms & don't know how to enter stock recovery?
Click to expand...
Click to collapse
Thank you very much yo solve my problem.
My bad for not knowing how to enter stock recovery.
Bootmenu
turffe said:
On Stock Recovery press Vol-up+down buttons... Rooting & flashing custom roms & don't know how to enter stock recovery?
Click to expand...
Click to collapse
I am new to the Defy, but managed to root and move to CM7 and all seems good. I just wondered if there is a version of bootmenu that uses touch screen rather than volume and power buttons? I thought one of the ICS ROMS had a touch screen recovery, but maybe I am thinking of HTC.
Thanks.
tomlogan1 said:
I am new to the Defy, but managed to root and move to CM7 and all seems good. I just wondered if there is a version of bootmenu that uses touch screen rather than volume and power buttons? I thought one of the ICS ROMS had a touch screen recovery, but maybe I am thinking of HTC.
Thanks.
Click to expand...
Click to collapse
Latest CM10 and CM10.1 have a touch bootmenu, even the latest CM 10.1 has TWRP 2.5 that it's a touch custom recovery.
Bootmenu 2
soyusado said:
Latest CM10 and CM10.1 have a touch bootmenu, even the latest CM 10.1 has TWRP 2.5 that it's a touch custom recovery.
Click to expand...
Click to collapse
Thanks for your reply.
I prefer CWM to TWRP, but is there a way to get the more advanced bootmenu 2 and keep CWM? Sndinitdefy seems to only have the recovery using the volume controls and power button.
Thanks.
tomlogan1 said:
Thanks for your reply.
I prefer CWM to TWRP, but is there a way to get the more advanced bootmenu 2 and keep CWM? Sndinitdefy seems to only have the recovery using the volume controls and power button.
Thanks.
Click to expand...
Click to collapse
I think Quarx merged that bootmenu when he started to make his 2ndboot nightlies for CM10, but I don't know how to install it separately from his .zip files, you should download some of the latest ROMs a see if you could merge the bootmenu to CM7.
where are you download this Froyo's .sbfs?
soyusado said:
Help me, please!
Yesterday, I wanted to make a clean install for the latest Quarx's CM 10.1 nightly (I've been flashing Quarx's builds for almost a year now, he's The Best), but I think I made a terrible mistake.
When I wanted to make a factory reset, I've got this error because the sd-ext, I understand, that happened because TWRP's structure with almost all devices running Android 4.2.2 have a virtual-sd and a sd-ext, so I decided to make an Advance wipe and I every damn box, even wipe system and wipe sd card.
Finally when I rebooted my phone, TWRP asked to install SU, I pressed yes.
Then when my phone was rebooting, I've got this error:
Bootloader
09.10
Err:A5,70,39,00,27
So, I've been flashing Froyo's .sbfs since yesterday, when I get pass verification from RSDLite and rebooted the phone, it just keep bootlooping, I left it almost 15 minutes and still in Froyo's bootanimation, I know it has to do because it's needed wipe data and cahe, but I can't do that because I can't access stock recovery (volume down+power button), I just get the triangle with the little Android in it.
Here's is the .sbf
JORLA_U3_3.4.2_108-5_SIGNED_USAJORDMR1B25CLALALA022.0R_JORLAFROCLALALA_P027_A018_M016_HWp3_WIG147154_Service1FF.sbf.gz
And I did it with RSDLite 5.6.
Hope you can help me, thanks anyway.
Click to expand...
Click to collapse
i do the same step to my defy and now i face the same problem .i think you have salve this problem .but i can't find the this file :JORLA_U3_3.4.2_108-5_SIGNED_USAJORDMR1B25CLALALA022.0R_JORLAFROCLALALA_P027_A018_M016_HWp3_WIG147154_Service1FF.sbf.gz
can you gave me a download adress? i am a chinese and have poor english level ,can you tell me the way you fix your phone step by step? think you !
This thread should help (http://forum.xda-developers.com/showthread.php?t=1216982), in there you'll be able to find everything you need to fix your phone.
First download RSDLite, then search for a sbf suitable for your country.
Then flash it, you need to have Motorola drivers installed and plug the phone on bootloader mode (press volume up+power button), you have to paste the sbf file you extracted in the RSDLite folder, then just execute it and browse the sbf file, finally press flash and wait.
When you read "please start your phone manually" or something like that, disconnect your phone, remove the battery for five seconds then start it on bootloader mode and plug it.
Your phone should boot to Android.
If you get stuck on bootanimation, wipe data and cache from stock recovery (volume down+power button, when you see the triangle press volume volume up+volume down).
Your phone is ready to go now.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
think you so much
soyusado said:
This thread should help (http://forum.xda-developers.com/showthread.php?t=1216982), in there you'll be able to find everything you need to fix your phone.
First download RSDLite, then search for a sbf suitable for your country.
Then flash it, you need to have Motorola drivers installed and plug the phone on bootloader mode (press volume up+power button), you have to paste the sbf file you extracted in the RSDLite folder, then just execute it and browse the sbf file, finally press flash and wait.
When you read "please start your phone manually" or something like that, disconnect your phone, remove the battery for five seconds then start it on bootloader mode and plug it.
Your phone should boot to Android.
If you get stuck on bootanimation, wipe data and cache from stock recovery (volume down+power button, when you see the triangle press volume volume up+volume down).
Your phone is ready to go now.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
Click to expand...
Click to collapse
thank you,perhaps it will work , but i don't know my defy produced by which country , can i use the other country's sbf ?
Yong-Zhi Lee said:
thank you,perhaps it will work , but i don't know my defy produced by which country , can i use the other country's sbf ?
Click to expand...
Click to collapse
It's not the country your Defy proceeds, you need to know the country for your carrier's signal.
Related
i flash my phone with a custom rom from this forum
succesfull until RSD Lite step
after RSD Lite, my phone stuck at Motorola logo with blur
tried pull off and pulling on the batery with power and volume up, it got back to bootloader screen
try aother RSD Power, it is still the same
Progress till 100 persen, but the phone stucked at motorola blur logo
any solution, guys?
thanks
What were you trying to flash?
I try to upgrade to froyo.
it stuck after RSD Lite step
Well first, is your phone rooted? Secondly, what stock version did you have?
I think I can get you up and running with Froyo
you may try to install your original version/build number sbf. if its work, maybe you can try flash froyo ROM again. then when you finished restore custom ROM all you have to do is go to bootloader then flash boot/devtree only sbf.. dont pull usb connection. but if RSD want you to turn phone manually then you need to press power button even though your phone at booting state..
i got the same problem, everything was working fine before i done it a couple times but then i used miui and my phone battery died and it wouldnt work after that so i decided to flash with rsd lite and after doing everything normally its just stuck at the motorola and moto blur symbol/animation thing. really frustrating.
-ashur
FL4M3K1NG said:
i got the same problem, everything was working fine before i done it a couple times but then i used miui and my phone battery died and it wouldnt work after that so i decided to flash with rsd lite and after doing everything normally its just stuck at the motorola and moto blur symbol/animation thing. really frustrating.
-ashur
Click to expand...
Click to collapse
did you find fix?
What SBF file did you use?
Have you tried another file?
get into stock recover (Vol Up + Power) then wipe data/cache
Half Bricked
I have an Mb525 rooted (that was) running stock 2.2 Blurred. I installed the Defy boot loader and hard reset/wiped partitions and (tried to) install cm7 from SD, it installs fine, goes fine, everything is all set. Reboot the device and the splash image pops up with the white LED first, then the blue one for boot loader, and finally the green one. It stays on splash screen. I tried 2 different versions of cm7 and both do the same thing. I'm able to access the boot loader, it just doesn't finish loading whatever I flash onto it.
As my phone is dysfunctional, I would appreciate it if you could contact me through my Skype;
kurtdunsmore
I won't receive emails.. =/
Specs:
Moto Defy shipped with 2.1
Rooted
Red Lense
T-Mobile, U.S.A.
Please let me know if any other information would be helpful.
tendyfish said:
get into stock recover (Vol Up + Power) then wipe data/cache
Click to expand...
Click to collapse
to go in stock recovery u must use Vol Down + Power
Solution
I had this problem. Found a solution at 4pda.ru
1. Shut down your phone.
2. Hold Volume- button, press Power button for 2 seconds. Then release both.
3. When you see Android robot press together both Volume+ and Volume- buttons.
4. Erase both Cache and Data.
5. Reboot.
Your phone should boot normally.
aed0101 said:
I had this problem. Found a solution at 4pda.ru
1. Shut down your phone.
2. Hold Volume- button, press Power button for 2 seconds. Then release both.
3. When you see Android robot press together both Volume+ and Volume- buttons.
4. Erase both Cache and Data.
5. Reboot.
Your phone should boot normally.
Click to expand...
Click to collapse
This worked perfectly well. Thank you.
Andy
Thanks to r2beta0 for fixing the issuse related to /data and overclocking.
Thanks to sw_acer for porting and the original link here http://bbs.gfan.com/android-2194589-1-1.html
This bootmenu is ported from Defy !
Install tutorial:
1. Apply Bootmenu v0.8.6-v2.zip via CWM (droid2bootstrap);
2. Then reboot, your phone should enter bootmenu. Press volume up/down key to highlight and power button to select/confirm;
3. Enter boot->Set default: ->[choose the default boot method you want] ;
4. In normal cases, you will see the led goes blue for 1.5 sec during booting and then you can enable bootmenu by pressing volume keys.
Features:
1. Overclocking;
2. Choose to enable Custom Recovery 3.1.0.0 or Stock Recovery;
3. Support adb in Custom Recovery mode
Tips: Not recommend to set default boot method as 2nd-init or 2nd-boot if you are not a DEV. If you have set it to 2nd-int or 2nd-boot and cause bootloop. Don`t flash sbf first. Because you can re-enter bootmenu by pressing volume key when you see LED goes blue during booting. And then please set back to boot bootmenu or normal boot. So your phone will not bootloop anymore.
Thanks for posting it here. I just tried it and it works like a charm.
I'm not familiar with Defy's BootMenu, but why would I want to use it over the default CWM Recovery?
w0ndersp00n said:
I'm not familiar with Defy's BootMenu, but why would I want to use it over the default CWM Recovery?
Click to expand...
Click to collapse
Of course you can choose not to use this. But Defy's BootMenu provides more function other than just recovery.
Hmmmm... my phone bootloops. Now I've got to flash it.
frenetico said:
Hmmmm... my phone bootloops. Now I've got to flash it.
Click to expand...
Click to collapse
Have you choose the wrong boot method, try to select normal boot. You can press vol key to re-enter the bootmenu when the LED light up instead of flashing sbf.
Edit: Here in my phone it works fine...
Endless7 said:
Have you choose the wrong boot method, try to select normal boot. You can press vol key to re-enter the bootmenu when the LED light up.
Edit: Here in my phone it works fine...
Click to expand...
Click to collapse
Yeah. That's exactly what I did. I even fomatted cache partition. The phone was forcing the boot the whole time. Even when I pulled the battery the phone started to boot normally, which means, that I couldn't enter CWM.
After that I deinstalled the boot menu resulting in .sbf-ing the phone.
frenetico said:
Yeah. That's exactly what I did. I even fomatted cache partition. The phone was forcing the boot the whole time. Even when I pulled the battery the phone started to boot normally, which means, that I couldn't enter CWM.
After that I deinstalled the boot menu resulting in .sbf-ing the phone.
Click to expand...
Click to collapse
When the phone boot to logo M, you should see the LED right-up goes blue for 1.5 sec. During this 1.5 sec, press any volume keys and you will enter bootmenu again. And then you can choose to enable CWM or any other thing.
Now I .sbf-ed the phone, wiped it and still it doesn't boot properly. Damn...
frenetico said:
Now I .sbf-ed the phone, wiped it and still it doesn't boot properly. Damn...
Click to expand...
Click to collapse
Still bootloop ?
Unfortunately, yes. Gotta send it back but who cares.
frenetico said:
Unfortunately, yes. Gotta send it back but who cares.
Click to expand...
Click to collapse
I have tried and found restore /system only can undo the .zip and flashing sbf do the same. Maybe your bootloop is caused by other thing.
Damn those guys of 3 Austria. Now I found the reason for not booting. My SIM card is totally destroyed. Now I put a second SIM card in there and surprise: My beloved Milestone 2 boots normally.
Thanks
Let´s see if we find a way to boot cm7...
Sry for offtopic. Does this mean, we have a new possible way of booting something else, than Motorola stock roms?
This is not a real port... The hole bootmenu, CWM recovery and overclock modules are built for Defy. The only things that changed from the bootmenu that you can download from Market are the icons and (not sure) you can navigate with the keyboard.
Well, if you want a real MS2 recovery use the MS2Bootstrapper.apk (Chinese, it's somewhere in the forum) or build a new bootstrap recovery from source.
Sent from my Milestone 2 XDA App
Is it compatible with the latest last china GB leek?
And can we replace CWM3(from defy) to CWM4(from MileStone2Bootstrap_GoAPK.apk)?
xenusr said:
Is it compatible with the latest last china GB leek?
And can we replace CWM3(from defy) to CWM4(from MileStone2Bootstrap_GoAPK.apk)?
Click to expand...
Click to collapse
Yes it is compatible. But don't try to install Milestone2Bootstrap_GoAPK side by side with any other CWM/Bootmenu.
@Milestone 2 (Finnaly on Gingerbread!)
The recovery isn't working fine. Something is wrong with /data and recovery can't mount or format it as expected.
Edit: Ok, could get the darn thing to work here Endless7, you have to edit /system/bootmenu/recovery/sbin. The scripts tune2fs (hijack) and mk2fs (hijack) are pointing to mmcblk1p25 instead of p26.
r2beta0 said:
The recovery isn't working fine. Something is wrong with /data and recovery can't mount or format it as expected.
Edit: Ok, could get the darn thing to work here Endless7, you have to edit /system/bootmenu/recovery/sbin. The scripts tune2fs (hijack) and mk2fs (hijack) are pointing to mmcblk1p25 instead of p26.
Click to expand...
Click to collapse
I have build a new one, but I cant test it yet. Now I am running MIUI, install any other recovery will break the 2nd-init for ROM.
hi 2 all
I want to brief how made brick my tab step by step
first of all i had an Acer_A500_4.010.43_COM_GEN1 3.1 stock rom on my tab that i upgrade it to 3.2 Acer_A500_7.006.01_COM_GEN1 by tablet then i decided to root my tablet for installation custom rom and i downgrade to 3.01 rom by this typic http://forum.xda-developers.com/showthread.php?t=1276227 method 1 i reverted successfully and after rooting i installed and tested this 3 roms (taboonay 2.2-thor 14.2&light speed 1.07) but each one had some problems like google map or gps or rotation screen so i installed a 3.1hc stock rom Acer_A500_4.010.41_COM_GEN1 and rooted that worked good but i had mistake and i forget erase update.zip file from my sd card
4days ago Mistakenly I turn on my tablet with recovery mode and iconia automattically gone to update mode (rom installation) i did nothing but this opration was stopped at 80% and my wrong was here i could not be patient and shut down my tab by power button and i bricked my tablet
after that i test all method for unbrick it like not stable rom , Chinese and whitout Chinese roms using of stock rom like Acer_A500_4.010.38_COM_GEN1
without any success only in not stable rom processes gone to 95 % and then stoped and nothing
after update to chinese rom it stopped at 30 % with yellow triangle sign
and then happend something bad and i loose my CWM
NOW if i want to go to recovery mode by pressing power+vol down keys Iconia show me a message
secure boot: image SOS checksum fail!
and in normal booting I have a locked black screen with nonworking touchables button and android word at left top of screen and clock & 15% battery sometimes it show a message for shutting down
i cant go to setting menu for active my usb debugging and my pc do not recognize my tablet
i cant hard reset my tab because it hanged in 2 message for 30 mins and i cant go to recovery mode and customer services says your device is out of warranty because rotting that
but Fortunately I have my UID
excuse me for long story
any body help me please
thank all of you
that is amazing over 150 visit of this help request without any answer please give me a Proposal
thanks
I have a501 .....
http://forum.xda-developers.com/showthread.php?t=1419164
the chinese rom and checksum error are supposed to happen.
the chines rom is an old unstable version but is provided so we can root it to install cwm and flash a working rom.
after the checksum error you needed to power off and then using the buttons enter recovery mode and go to 'Fix checksum error' in advanced menu - after that reboot.
you should do the following:
a)go back and read the entire post on what to do because you missed the last part
or
b)try the backdoor method
---------- Post added at 12:21 PM ---------- Previous post was at 11:49 AM ----------
just read your entire post again...there's alot going on there isnt there?
have you tried flashing the update.zip again with 3.0.1 on it...get back to the chinese rom, from there install iconia root and root it. Then install cwm and you should be all good - if that doesnt work then use timmyDeans backdoor method it does it for you, all you need to do is install acer recovery installer to install cwm, backup the original stock recovery when the app asks you, you will need it to OTA Update successfully...
Doesn't flashing stock rom remove cwm?
bendystrawboy said:
Doesn't flashing stock rom remove cwm?
Click to expand...
Click to collapse
yeh i just had trouble when i OTA'd last nite on the 2nd update, had to flash stock before it would install, but i may have restored the wrong one from acer recovery installer beforehand...a definite possibility!!!
by flashing from method 1 my racovery mode came back again and i can recover only from update.zip
but when i want to install Extract_unBrick_UPDATE it stop at 30% and my tab goes to turn off and when i press power button it turnnig on and turn off very soon and can not boot
I test non stable rom and flash with this rom proccess goes to 90% and stop
what can i do now? this is my tablet screen
http://s1.picofile.com/file/7237922040/Photo_0007.jpg
http://s2.picofile.com/file/7237923010/Photo_0008.jpg
http://s1.picofile.com/file/7237924301/Photo_0009.jpg
thank u
darvis said:
by flashing from method 1 my racovery mode came back again and i can recover only from update.zip
but when i want to install Extract_unBrick_UPDATE it stop at 30% and my tab goes to turn off and when i press power button it turnnig on and turn off very soon and can not boot
I test non stable rom and flash with this rom proccess goes to 90% and stop
what can i do now? this is my tablet screen
http://s1.picofile.com/file/7237922040/Photo_0007.jpg
http://s2.picofile.com/file/7237923010/Photo_0008.jpg
http://s1.picofile.com/file/7237924301/Photo_0009.jpg
thank u
Click to expand...
Click to collapse
Unbrick it using my tool listed here, guarantee you it will fix your problems.
Just download it and follow the instructions in the readme.pdf.
http://forum.xda-developers.com/showpost.php?p=20680452&postcount=137
timmyDean said:
Unbrick it using my tool listed here, guarantee you it will fix your problems.
Just download it and follow the instructions in the readme.pdf.
http://forum.xda-developers.com/showpost.php?p=20680452&postcount=137
Click to expand...
Click to collapse
hello master
i am so glad for your attention to my problem
i use from your rom before that pictures are shown above and my tablet show ((pass)) and pc show congratulation to me but u see nothing change but Hopefully that fix my cvm problem an now ican use from update.zip rom but my screen didn't any change and i cant do anything by tablet
I don't know anything about backdoor method is it useful for my problem ?
i have 2 problems
1-i cant wipe and erase my whole data even when i press vol+ and power keys and toggle lock screen button it shown two message for erasing cash but it do anything
2-my PC don't recognize my tablet i have to flash your rom with APX mode
i have a question do your rom need to CUPID file ? because there isn't any cupid file in your Rom
please help me sir because you are a greet master
thanks
darvis said:
hello master
i am so glad for your attention to my problem
i use from your rom before that pictures are shown above and my tablet show ((pass)) and pc show congratulation to me but u see nothing change but Hopefully that fix my cvm problem an now ican use from update.zip rom but my screen didn't any change and i cant do anything by tablet
I don't know anything about backdoor method is it useful for my problem ?
i have 2 problems
1-i cant wipe and erase my whole data even when i press vol+ and power keys and toggle lock screen button it shown two message for erasing cash but it do anything
2-my PC don't recognize my tablet i have to flash your rom with APX mode
i have a question do your rom need to CUPID file ? because there isn't any cupid file in your Rom
please help me sir because you are a greet master
thanks
Click to expand...
Click to collapse
V3 which I pointed you to is STOCK 3.2.1 with root. Once you get there you will be stable. If you want CWM then you will have to install it. It is NOT in the flash because the flash is stock ONLY with root. But since you have root, you can install CWM.
The serial number does NOT need to be saved in any file. Just follow the instructions.
timmyDean said:
V3 which I pointed you to is STOCK 3.2.1 with root. Once you get there you will be stable. If you want CWM then you will have to install it. It is NOT in the flash because the flash is stock ONLY with root. But since you have root, you can install CWM.
The serial number does NOT need to be saved in any file. Just follow the instructions.
Click to expand...
Click to collapse
sorry sir
I used your v3 rom and install it by apx mode it installed and I saw ((pass)) on my tablet after botting and after acer logo and android word i have same problem yet
http://s1.picofile.com/file/7238522040/Photo_0010.jpg
http://s2.picofile.com/file/7238522903/Photo_0011.jpg
http://s1.picofile.com/file/7238523331/Photo_0012.jpg
however thank you very much for your attention
sincerely yours
darvis said:
sorry sir
I used your v3 rom and install it by apx mode it installed and I saw ((pass)) on my tablet after botting and after acer logo and android word i have same problem yet
http://s1.picofile.com/file/7238522040/Photo_0010.jpg
http://s2.picofile.com/file/7238522903/Photo_0011.jpg
http://s1.picofile.com/file/7238523331/Photo_0012.jpg
however thank you very much for your attention
sincerely yours
Click to expand...
Click to collapse
Ok, now just download the stock image for your country and put it on your external sdcard. Use the power and volume + key which will launch stock recovery (which you now have flashed) and it will flash your tablet with the one located on your sdcard. This will have you back stock.
timmyDean said:
Ok, now just download the stock image for your country and put it on your external sdcard. Use the power and volume + key which will launch stock recovery (which you now have flashed) and it will flash your tablet with the one located on your sdcard. This will have you back stock.
Click to expand...
Click to collapse
sorry sir
what did you mean about power and volume + key?
do you mean power and vol down keys for recovery mode?
darvis said:
sorry sir
what did you mean about power and volume + key?
do you mean power and vol down keys for recovery mode?
Click to expand...
Click to collapse
You have a "volume" switch on top of your tab (long silver switch on left side)
You control volume from this. Vol+ make sound go up (the right side of it)
Press it on the left side, and volume goes quiet (vol-)
So, as he said, with the tablet OFF, hold the VOL+ side of the button, then select PWR (power)
You have 2 recovery modes.
1. CWM Recovery (vol- & Pwr) (after you have root and cwm installed)
2. Stock Acer recovery (vol+ & Pwr)
Step number 2 with the stock acer recovery, should install the stock rom you copied to your sd like TimmyDean said earlier.
Moscow Desire said:
You have a "volume" switch on top of your tab (long silver switch on left side)
You control volume from this. Vol+ make sound go up (the right side of it)
Press it on the left side, and volume goes quiet (vol-)
So, as he said, with the tablet OFF, hold the VOL+ side of the button, then select PWR (power)
You have 2 recovery modes.
1. CWM Recovery (vol- & Pwr) (after you have root and cwm installed)
2. Stock Acer recovery (vol+ & Pwr)
thanks a lot
Step number 2 with the stock acer recovery, should install the stock rom you copied to your sd like TimmyDean said earlier.
Click to expand...
Click to collapse
thank u sir
but there is a question
1-in CWM recovery we can use from Update.zip files
but in Stock Acer recovery (vol+&power ) which one of files must be copied at sd card ?
darvis said:
thank u sir
but there is a question
1-in CWM recovery we can use from Update.zip files
but in Stock Acer recovery (vol+&power ) which one of files must be copied at sd card ?
Click to expand...
Click to collapse
Answer me please
darvis said:
Answer me please
Click to expand...
Click to collapse
Please rewrite what you are trying to do. I have no idea what you are talking about?
Are you asking about stock recovery and flashing form a SD Card? If so, copy update.zip to your SD card and then run recovery. If you have CWM, then use it to select the update from the SD Card.
It's not clearly as to exactly what you have loaded and what you are trying to do?
LASTLY: You cannot take a backup from CWM and have the stock recovery install it. Stock recovery will only install update.zip which must be signed by ACER.
TD
timmyDean said:
Please rewrite what you are trying to do. I have no idea what you are talking about?
Are you asking about stock recovery and flashing form a SD Card? If so, copy update.zip to your SD card and then run recovery. If you have CWM, then use it to select the update from the SD Card.
It's not clearly as to exactly what you have loaded and what you are trying to do?
LASTLY: You cannot take a backup from CWM and have the stock recovery install it. Stock recovery will only install update.zip which must be signed by ACER.
TD
Click to expand...
Click to collapse
Hello sir
in upper post u tell me i must go to recover mode by pressing power & vol+
but only i can go to stock recovery with pressing power & vol-(not vol+)
is there any other method for going to recovery mode by (vol+) ?
because Mr Moscow Desire said in his upper post (post no 14 of this thread)
if yes how ?
if not ..... just thank u
there is only one recovery on your device..
you should slowly repost your exact trouble.. then do EXACTLY as someone tell you to fix it..
There is only one recovery on your device . If YOU FLASH CWM RECOVERY .. it overrides the acer recovery.
so if you dont have cwm revovery .
nevermind repost your system rom you are using .. rather or not you know what recovery you have .. Then someone can help you...
LOST BLONDE BABE I AM .. GIGGLES
gOOD LUCK..
Sorry you're having difficulty.
Please go here and download the is tool http://forum.xda-developers.com/showthread.php?t=1307539
Do EXACTLY what it says to do in the PDF
hey, i have moto defy with custom rom MIUI 2.3.7 miui version 2.3.16. yesterday i got weekly miui rom update and cellphone download it and istalled it succesfulyy in recovery mode.
latest version are 2.3.23.
After update when phone reboots,it stucks on red moto logo, and cant pass it.
I reset it from recovery and also wipe cache. but still cant pass from red logo.
And recovery not showing full menu, there are just 4, like install update from sd card, reboot, wipe date,wipe cache.
plz tell where is the other option like install from sd card,so that i can reinstall rom. i put rom in card and press install update.zip in recovery but it got aborted.
Plz help what to do?
Do not worry!
cute_kayani said:
hey, i have moto defy with custom rom MIUI 2.3.7 miui version 2.3.16. yesterday i got weekly miui rom update and cellphone download it and istalled it succesfulyy in recovery mode.
latest version are 2.3.23.
After update when phone reboots,it stucks on red moto logo, and cant pass it.
I reset it from recovery and also wipe cache. but still cant pass from red logo.
And recovery not showing full menu, there are just 4, like install update from sd card, reboot, wipe date,wipe cache.
plz tell where is the other option like install from sd card,so that i can reinstall rom. i put rom in card and press install update.zip in recovery but it got aborted.
Plz help what to do?
Click to expand...
Click to collapse
Hello there!
As you mentioned that you are not able to see other Recovery options like "Install from zip" etc. This is because you must be booting your phone into the Stock Recovery. For those extra options to come up we need to boot the phone into the Custom Recovery.
To boot into Custom Recovery:
1. Press power on button;
2. Notice when the LED light blinks "BLUE" color; press both the volume keys this time;
3. Now it should show you Custom Recovery options this time;
4. Select "Install from Zip" and flash the ROM you were trying to flash (Also refer to the ROM info if that has some special installation steps).
If the above steps does not resolves the issue then you can always flash you phone with the Stock ROM found in the following article named as SBF:
http://forum.xda-developers.com/showthread.php?t=1216982
[Note: Above mentioned article has all the information that a defy user needs. Thanks "Zephyrot" for that wonderful article.]
Hope that helps!
Good Luck!!
there is no blue led, when press power button it stuck on red moto logo..
and when press both vol down and power it goes into recovery with limited options.
can it is possible i put rom into sd card and rename it with Update.zip and then in recovery use it with update zip..
or any other solution
Thanks
cute_kayani said:
hey, i have moto defy with custom rom MIUI 2.3.7 miui version 2.3.16. yesterday i got weekly miui rom update and cellphone download it and istalled it succesfulyy in recovery mode.
latest version are 2.3.23.
After update when phone reboots,it stucks on red moto logo, and cant pass it.
I reset it from recovery and also wipe cache. but still cant pass from red logo.
And recovery not showing full menu, there are just 4, like install update from sd card, reboot, wipe date,wipe cache.
plz tell where is the other option like install from sd card,so that i can reinstall rom. i put rom in card and press install update.zip in recovery but it got aborted.
Plz help what to do?
Click to expand...
Click to collapse
I guess you'd charge your phone first then wait for a while,
cute_kayani said:
there is no blue led, when press power button it stuck on red moto logo..
and when press both vol down and power it goes into recovery with limited options.
can it is possible i put rom into sd card and rename it with Update.zip and then in recovery use it with update zip..
or any other solution
Thanks
Click to expand...
Click to collapse
I'm disappointed to know that you are still facing the same issue. Also, renaming the file to update.zip will not let you flash it.
As suggested above first recharge your battery for a while and then flash with appropriate SBF of your region using RSD Lite. Refer to the above given link it has all the information. Also, note that if you flash with any particular android version SBF (which is not a fixed SBF) then you will not be able to downgrade (above article has all info).
Hope this helps!
Good Luck!
Okay, thanks for all.. this is the T Mobile Uk version and i got it with eclair rom, and than updated with orignal T mobile froyo.
Now i should start from froyo or eclair?
cute_kayani said:
Okay, thanks for all.. this is the T Mobile Uk version and i got it with eclair rom, and than updated with orignal T mobile froyo.
Now i should start from froyo or eclair?
Click to expand...
Click to collapse
You may use any ROM either Froyo or Eclair. Please also check the downgradilbility of the ROM. As in many of the cases if the ROM is not fixed then switching back to the earlier versions is impossible without having the Nandroid backup. I suggest you to use the version which is officially released in your region.
ROMs can be downloaded from the below mentioned link:
http://and-developers.com/sbf:defy
Complete information about various SBFs at:
http://forum.xda-developers.com/showthread.php?t=966537
Hope this helps!
Happy Flashing!
i flash it with JRDNEM_U3_2.21.0_SIGNED_UCAJRDNEMARAB1B80AA028.0R_USAJORDANRTGB_P026_A007_HWp3_Service1FF.sbf
and i got staus passed message and cellphone reboots.
but now it is not going in recovery/bootloader or power on.
what is this?
but when i connect usb ,rsd detect it..but this time no white led also.
I again flash it with JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_USAJRDNEMARAB1B8TMGB030.0R_USAJORDANTMGB_P039_A015_M003_HWp3_Service1FF.sbf
successfully passed and message pop for reboots,but still black screen.
Rajneeshgadge17 said:
Hello there!
As you mentioned that you are not able to see other Recovery options like "Install from zip" etc. This is because you must be booting your phone into the Stock Recovery. For those extra options to come up we need to boot the phone into the Custom Recovery.
To boot into Custom Recovery:
1. Press power on button;
2. Notice when the LED light blinks "BLUE" color; press both the volume keys this time;
3. Now it should show you Custom Recovery options this time;
4. Select "Install from Zip" and flash the ROM you were trying to flash (Also refer to the ROM info if that has some special installation steps).
If the above steps does not resolves the issue then you can always flash you phone with the Stock ROM found in the following article named as SBF:
http://forum.xda-developers.com/showthread.php?t=1216982
[Note: Above mentioned article has all the information that a defy user needs. Thanks "Zephyrot" for that wonderful article.]
Hope that helps!
Good Luck!!
Click to expand...
Click to collapse
Tnx for post guy
Palestrino said:
Tnx for post guy
Click to expand...
Click to collapse
Thanks,
I tried but there was no blue led and flash it two time but now black screen is the hurdle.
please tell how to pass this.
While flashing there was message for successful status, and reboot but now when i press power button nothing happen. And neither goes into boot loader or recover.
Only RSD detects my phone for flashing, otherwise its complete dead....
ohhhoooooo MIUI Rom You ruined my DEFY (
cute_kayani said:
i flash it with JRDNEM_U3_2.21.0_SIGNED_UCAJRDNEMARAB1B80AA028.0R_USAJORDANRTGB_P026_A007_HWp3_Service1FF.sbf
and i got staus passed message and cellphone reboots.
but now it is not going in recovery/bootloader or power on.
what is this?
but when i connect usb ,rsd detect it..but this time no white led also.
Click to expand...
Click to collapse
cute_kayani said:
I again flash it with JRDNEM_U3_2.51.1_BLUR_P3_SIGN_SIGNED_USAJRDNEMARAB1B8TMGB030.0R_USAJORDANTMGB_P039_A015_M003_HWp3_Service1FF.sbf
successfully passed and message pop for reboots,but still black screen.
Click to expand...
Click to collapse
What we need to do?
We are launching Stock Recovery and wiping cache and data.
Use below mentioned steps:
1. Remove battery from phone and then reinsert;
2. Press and hold Volume Down button along with Power button till you see Android icon with an exclamation mark (!);
3. Once you see android icon and exclamation mark release both buttons and now press volume up and volume down button together;
4. Above steps will launch Android System Recovery window (Stock Recovery);
5. Now “wipe data/factory reset” by pressing volume down key and to select press power key;
6. On the next screen it will prompt you to confirm this option by selecting “yes – delete all use data” select this option with power key again;
6. Also “wipe cache partition” from power key as mentioned above;
7. Now select “reboot system now”;
After above steps it will take around 3-5 minutes for first boot and your phone will now boot in normal state.
If the above steps does not resolves the issue then I would recommend you to use some other SBF depending on your region.
Hope this helps!
Thanks Rajneeshgadge17..
When i press these buttons nothing is happening. and i charge up battery with universal charger, don't know what is wrong.
only RSd detect my phone when i plugin USB.. otherwise it seems completely dead.
can somebody help........
cute_kayani said:
can somebody help........
Click to expand...
Click to collapse
Refer this post = http://forum.xda-developers.com/showpost.php?p=24205029&postcount=2
What if I have balck screen in recovery mode as well?
Do you have any idea how to solve the same problem if the recovery mode does not start neither? Only RSDLite sees that the phone is connected. I can refresh the ROM but I did not find the right .sbf file yet. Do you know maybe which one would bring back the phone from death?
Thank you in advance!!
Rajneeshgadge17 said:
What we need to do?
We are launching Stock Recovery and wiping cache and data.
Use below mentioned steps:
1. Remove battery from phone and then reinsert;
2. Press and hold Volume Down button along with Power button till you see Android icon with an exclamation mark (!);
3. Once you see android icon and exclamation mark release both buttons and now press volume up and volume down button together;
4. Above steps will launch Android System Recovery window (Stock Recovery);
5. Now “wipe data/factory reset” by pressing volume down key and to select press power key;
6. On the next screen it will prompt you to confirm this option by selecting “yes – delete all use data” select this option with power key again;
6. Also “wipe cache partition” from power key as mentioned above;
7. Now select “reboot system now”;
After above steps it will take around 3-5 minutes for first boot and your phone will now boot in normal state.
If the above steps does not resolves the issue then I would recommend you to use some other SBF depending on your region.
Hope this helps!
Click to expand...
Click to collapse
Ryaren said:
Do you have any idea how to solve the same problem if the recovery mode does not start neither? Only RSDLite sees that the phone is connected. I can refresh the ROM but I did not find the right .sbf file yet. Do you know maybe which one would bring back the phone from death?
Thank you in advance!!
Click to expand...
Click to collapse
Try to find the latest stock rom from your region... and match with ur defy type... flash with rsd that would bring ur defy back
Sent from my XT535 using xda premium
Doesn't work for me
Rajneeshgadge17 said:
What we need to do?
We are launching Stock Recovery and wiping cache and data.
Use below mentioned steps:
1. Remove battery from phone and then reinsert;
2. Press and hold Volume Down button along with Power button till you see Android icon with an exclamation mark (!);
3. Once you see android icon and exclamation mark release both buttons and now press volume up and volume down button together;
4. Above steps will launch Android System Recovery window (Stock Recovery);
5. Now “wipe data/factory reset” by pressing volume down key and to select press power key;
6. On the next screen it will prompt you to confirm this option by selecting “yes – delete all use data” select this option with power key again;
6. Also “wipe cache partition” from power key as mentioned above;
7. Now select “reboot system now”;
After above steps it will take around 3-5 minutes for first boot and your phone will now boot in normal state.
If the above steps does not resolves the issue then I would recommend you to use some other SBF depending on your region.
Hope this helps!
Click to expand...
Click to collapse
Unfortunately it doesn’t work for me, my defy doesn’t react for any key combination. RSD Lite still discovers it I can flash any sbf’s. But I’m still getting black screen. The problem is that I don’t know which sbf I should use… Please help. I know I can’t brick defy but if I don’t know how to get back I’m almost there…
0lsztyN said:
Unfortunately it doesn’t work for me, my defy doesn’t react for any key combination. RSD Lite still discovers it I can flash any sbf’s. But I’m still getting black screen. The problem is that I don’t know which sbf I should use… Please help. I know I can’t brick defy but if I don’t know how to get back I’m almost there…
Click to expand...
Click to collapse
It seems an issue with the Kernel. May be you are flashing the Green lense Defy (MB525) with GB kernel (i.e. MB526 sbf).
Also check the Bootloader version and which Android version you were using.
Here is a list of all the SBF's for both versions:
http://forum.xda-developers.com/showthread.php?t=966537
Hope this helps.
PS:- I don't use Defy for a year now as I own a Nexus 4.
Hi guys,
i have a milestone2 with cm7-tezet and i want upgrade to cm10 tezet. I read the installation guide, but i have not understand one step; i quote:
"Ensure you have GB kernel flashed. If you are upgrading from CM9, there's nothing you need to do. If you are upgrading from my CM7 ROM, flash kernel from this image first."
how i flash with new kernel?
reboot my milestone2 in recovery mode
go to "install zip from sd card"
select the new kernel
then? i must reboot or not?
the recovery mode not change with a new kernel?
thank you!
ipumba said:
Hi guys,
i have a milestone2 with cm7-tezet and i want upgrade to cm10 tezet. I read the installation guide, but i have not understand one step; i quote:
"Ensure you have GB kernel flashed. If you are upgrading from CM9, there's nothing you need to do. If you are upgrading from my CM7 ROM, flash kernel from this image first."
how i flash with new kernel?
reboot my milestone2 in recovery mode
go to "install zip from sd card"
select the new kernel
then? i must reboot or not?
the recovery mode not change with a new kernel?
thank you!
Click to expand...
Click to collapse
Go into bootmenu, custom recovery.
Flash kernel, flash cm10, flash google apps.
Wipe data/factory reset
Reboot phone
Enjoy CM10.
Lean946 said:
Go into bootmenu, custom recovery.
Flash kernel, flash cm10, flash google apps.
Wipe data/factory reset
Reboot phone
Enjoy CM10.
Click to expand...
Click to collapse
all ok!
i follow your step and now i have cm10! thank you
installed the kernel
Hi!
I upgraded my milestone 2, from Gingerbread to CM 10.
It worked fine for a week.
today i was playing with it to install Google Apps, and accidentally installed kernel files which i got from this website.
now my milestone cannot turn on, and I am left without a phone
Can anybody help me?!
tirona said:
Hi!
I upgraded my milestone 2, from Gingerbread to CM 10.
It worked fine for a week.
today i was playing with it to install Google Apps, and accidentally installed kernel files which i got from this website.
now my milestone cannot turn on, and I am left without a phone
Can anybody help me?!
Click to expand...
Click to collapse
Look for an SBF corresponding to the android version you had before CM10 here: http://and-developers.com/sbf:milestone2
And download it from here: http://sbf.droid-developers.org/umts_milestone2/list.php
Follow steps here: http://forum.xda-developers.com/showthread.php?t=1032372 in order to restore your phone.
Instead of pressing @ in step 9, you need to press both volume buttons.
Hope it helps.
Lean946 said:
Look for an SBF corresponding to the android version you had before CM10 here: http://and-developers.com/sbf:milestone2
And download it from here: http://sbf.droid-developers.org/umts_milestone2/list.php
Follow steps here: http://forum.xda-developers.com/showthread.php?t=1032372 in order to restore your phone.
Instead of pressing @ in step 9, you need to press both volume buttons.
Hope it helps.
Click to expand...
Click to collapse
thank you!
but RSD Lite is not yet available for download.
and the steps that the guy is explaining cannot be followed, cause my phone is completely dead.
it is off, and when trying to turn it on, it show the Motorola logo for 2 seconds and than disappears. the display of the phone remains powered but nothing happesn in there.
p.s. i can still go to root menu, by pressing and holding X + power button, and than X + Volume UP.
But with the reset data (wiping data / factory reset) nothing happens.
so still in dakr
When your device is off press On/Off button, vol +/- and the camera button.
Then you come to the bootloader. With RSD you can flash it.
FloOsen said:
When your device is off press On/Off button, vol +/- and the camera button.
Then you come to the bootloader. With RSD you can flash it.
Click to expand...
Click to collapse
I did everything in the right way.
i went into but menu (as it is described)
everything was executed smoothly with rsd lite. (i executed this file: 332.0 MiB 93F0ED6430C13DA551F984701D8C8C72 Retail Italian MILS2_U6_2.4.24_SIGNED_USAMILESTONE2B1B8RTIT00E.0R_USXMILE20RTIT_P030_A010_HWp2a_Service1FF.sbf.gz - because i bought in italy my phone)
but the phone is not starting up. and is not giving any sign (before it was showing the motorola logo for 2 seconds)
i cannot make any start using different kind of hard buttons combinations, like : X + power button, Camera + volume+ + power button, with or without USB cable try)
There is no sign of life from my phone
?!?!?!?!?!
tirona said:
I upgraded my milestone 2, from Gingerbread to CM 10.
Click to expand...
Click to collapse
tirona said:
(i executed this file: 332.0 MiB 93F0ED6430C13DA551F984701D8C8C72 Retail Italian MILS2_U6_2.4.24_SIGNED_USAMILESTONE2B1B8RTIT00E.0R_USXMILE20RTIT_P030_A010_HWp2a_Service1FF.sbf.gz - because i bought in italy my phone)
but the phone is not starting up. and is not giving any sign (before it was showing the motorola logo for 2 seconds)
i cannot make any start using different kind of hard buttons combinations, like : X + power button, Camera + volume+ + power button, with or without USB cable try)
There is no sign of life from my phone
?!?!?!?!?!
Click to expand...
Click to collapse
I think that, you chose wrong version of SBF...
look at this http://forum.xda-developers.com/showpost.php?p=19877027&postcount=386
henediac said:
I think that, you chose wrong version of SBF...
look at this http://forum.xda-developers.com/showpost.php?p=19877027&postcount=386
Click to expand...
Click to collapse
Hi!
this mate is explaining: "so i pulled out battery, pressed volDown + shutter and placed battery in, display remined black. But when I connected it to PC, and tried to flash with sbf_flash and (linux version of RSDlite) and (1) - it succed "
I tried also like him, but to my phone nothing happened....
?!!!!!?!?!?!?!!