Database Users

how can remove password on Wizard O2 Model ID: Wiza200.

hi every one,
i have one Wizard on O2 Model ID: Wiza200.
i wana remove password bcoz when u turn it on it ask u PASSWORD.
i dont know what's it.
i have JAFWM but how can i remove it no idea
i try to CAM+Softreset Button but when i try to connect it with JAFWM software and check factory settong and press Autodetect it say's
[15:02:23.219] J.A.F. for WindowsMobile by ODEON - ver 2.2g
[15:02:23.219] Program started: 2007-01-31
[15:02:29.117] ******** Starting Communication ********
[15:02:30.129] GetDeviceIdString
[15:02:30.129] *** channel write error
[15:02:30.129] ERROR: Could not determine device ID. Make sure device is in bootloader
[15:02:31.629] ******** Communication stopped ********
[15:02:31.629] ERROR: Could not find flasher for this device type.
[15:04:20.257] ERROR: Could not connect to device:
[15:04:20.267] - make sure device is connected in bootloader
[15:04:20.267] - ActiveSync is installed for drivers
[15:04:20.267] - firewall/antivirus software is turned off
but stange thing i have press Cam+Softreset button and fone is in Boot mode
any one can help me how can i remove password from it

Password
Hard reset.
Hold the device facing you, depress simultaneously the voice command and WiFi (connectivity) button. One is on the right side of the device and the other is on the left side of the device. With your other hand and the stylus, press the reset and hold it for a few moments.
Remove the stylus and continue holding the two buttons until onscreen instructions appear. You will need to then press the SEND key (as the instructions indicate) to do a hard reset.
Dare

hi man i did what u say but i dont now which is send key
i ask me press send key for defalt setting but which one is this
need ur help

the green phone button, the one you use to answer/make a call.

hi @helowsa
hi @hanmin
thanks man i have solved my problem Thanks for Replay and Help

thanks
lot of thanks brother great work.........

Hey I tried the hard reset on my phone and it prompts me to hit send, but when i do it doen't reset. Once it loads OS it prompts for pass word again. Plz help

YEH thanx great work

HTC break down! Help!

My HTC do not swich on. Today my battery dischargerd, when I pluged in power it did not swich on. It shows only red green blue white stripes. help!!!
Im sorry for may bad english

When I conect to my PC if finds some device and on HTC on white stripe is written USB

It's your SPL screen. Try this:
push the internet and message buttons together and reset your phone. It asks for reset, press the green phonekey. This hard-resets your device.

It does not help

Did you flash any ROM yesterday night ???

No
Only my HTC batterry full discharged.

Very strange, i don't know if is the case to use Mtty, wait for others opinions.

NeoS2007 said:
It's your SPL screen. Try this:
push the internet and message buttons together and reset your phone. It asks for reset, press the green phonekey. This hard-resets your device.
Click to expand...
Click to collapse
Neo's syggestion is correct maybe you did i wrong? if you do it correctly you will have a message saying
this operation will elete all of your personal data and reset all settings ro manufacturer default. press send to restore manufacturer default, or press other keys to cancel
the press green phone icon
if that fails download and flash the correct ROM for your phone i.e mine is avalible from o2 in english

Gene Dead

My htc gene is bricked.I have tried all the methods. I am unable to recover using Orefkov's method. When I try to press power key or soft reset button , onlr red and green light blinks. Nothing else happens. no charging indecator when i connect it to wall charger. I am even not getting the tri color screen.
please help me. to at least get into bootloader.
I have tried to connect using MTTY also but it is not detected using usb. help less now with no bootloader.

pravin.kamdi said:
My htc gene is bricked.I have tried all the methods. I am unable to recover using Orefkov's method. When I try to press power key or soft reset button , onlr red and green light blinks. Nothing else happens. no charging indecator when i connect it to wall charger. I am even not getting the tri color screen.
please help me. to at least get into bootloader.
I have tried to connect using MTTY also but it is not detected using usb. help less now with no bootloader.
Click to expand...
Click to collapse
don't panic
to enter boot loader just on device
press and hold camera button and press soft reset button .

deepv84 said:
don't panic
to enter boot loader just on device
press and hold camera button and press soft reset button .
Click to expand...
Click to collapse
No luck. I have tried to go to bootloader using press and hold camera button and press soft reset button

pravin.kamdi said:
No luck. I have tried to go to bootloader using press and hold camera button and press soft reset button
Click to expand...
Click to collapse
remove battery and then hold power button for 20 seconds (this will remove stored power from device )
then insert battery
press and hold camera button then press power to bootloader
hope this will work

Pravin,
What happened??
Did it work?

no bro i have tried power cycling also nothing is working.

ok dude did it worked?
if not tell me i'll help you via team vewer to unbrick it
dont worry just dont panic i've unbricked mine too

what happen
hey bro ,,
what happen, r u able u restore u r set...... if not tell us ...
bye

My Gene also dead
Please help me,,
i try to update rom but it fail,
now when i start my gene it show color screen...
please help me what i do
my yahoo chat id [email protected]

added you on yahoo

hey amit ,,
can u explain more in detail what u do exactly with u r handset..
.......

When i try to update my rom, i don`t know what happan but now, my phone not start when i try to start only blue and red light flash. nothing.
when i press reset with camera button i saw three color screen.
Tell me what i do..............

hello gurusingh,
I was update my htc p3400i ROM, after completion. Phone turn off but not restart, if I try camera button and reset button only green and red right blink not any indication shown on screen,…please help me.
I shall very thankful, if you solve my problem
Sanmukh singh
MSL, Mumbai.

hi gurusinghbrar,
My Htc p3400, can not start......
i was updating this rom "RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79.90_Ship" after 100% complete it turns off , but not start only Green and red light flash during press reset button...
i was try all methods,#remove batery 20 sec and then start with camer button & both camera and voice button. but result is same...
#No indication during Charging.,no usb detected in PC.
please help how i can recover my device.....
sanmukh singh
[email protected]

HTC P3400i GENE100 Dead
I have a HTC P3400i GENE100. I successfully installed orefkov SPL and then upgraded my original ROM WM 6.0 to cooked wm 6.5. After installation my device was too slow than before hence I flashed it with RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79 .90_Ship.exe. After flashing it 100 % my New Gene restarted, but didnt boot to booting screen. Its not going into bootloader mode also. It shows blank screen i.e. black. I tried several combinations of keys (Camera + Power button or Camera + Reset or by pressing both "-" button + Reset) for going it to bootloader mode. But none of them working. When I plug in charger the green & red light blinks once and nothing else. Same if I press reset with stylus, the green & red light blinks once and nothing else happens. I know that I have bricked my New Gene, when I flashed the ROM, which was meant for Old Gene, which I came to know after reading the posts in this forum. I have to use JTAG Method for recovering my Gene. Hence I have read many posts about it in this forum. But can any one of the great masters here, help me with a proper guide that can help me recover my Gene 100%.
Thank you for spending your valuable time in reading this post.
Regards
Parag Gawali

prgawali said:
I have a HTC P3400i GENE100. I successfully installed orefkov SPL and then upgraded my original ROM WM 6.0 to cooked wm 6.5. After installation my device was too slow than before hence I flashed it with RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79 .90_Ship.exe. After flashing it 100 % my New Gene restarted, but didnt boot to booting screen. Its not going into bootloader mode also. It shows blank screen i.e. black. I tried several combinations of keys (Camera + Power button or Camera + Reset or by pressing both "-" button + Reset) for going it to bootloader mode. But none of them working. When I plug in charger the green & red light blinks once and nothing else. Same if I press reset with stylus, the green & red light blinks once and nothing else happens. I know that I have bricked my New Gene, when I flashed the ROM, which was meant for Old Gene, which I came to know after reading the posts in this forum. I have to use JTAG Method for recovering my Gene. Hence I have read many posts about it in this forum. But can any one of the great masters here, help me with a proper guide that can help me recover my Gene 100%.
Thank you for spending your valuable time in reading this post.
Regards
Parag Gawali
Click to expand...
Click to collapse
check ur mail

Gene back to life
Thanks to Sumeet...
I got my HTC P-3400i New Gene back to life. It works better too. Sumeet is the man, who has given life to my entirely dead gene. I thank to him and suggest needy to contact him in their cases.
Thanks to XDA-developers Forum too...
Regards
Parag Gawali

same problem i had pls help me
Fido/Sumeet, please help me my gene got bricked when i was downgrading my gene from 6.1 to stock rom. after successful rom update my gene doesnt got restarted i'm getting black blank screen.
pleaseeeeeeeeeeee guys help me.....

P3400 gene100 is not starting!

Hi,
My 3400 is not starting. When i start the phone it hangs up in the "windows mobile direct push technology" screen. I tried without SD card and SIM but no luck. I have all my contacts inside and I need them. How can I fix the problem of my phone. Please help.
ONBL 1.10.0000
SPL 1.10.0000
GSM 2.79.90
OS 1.10.0.0
-aneesh

aneeshnr said:
Hi,
My 3400 is not starting. When i start the phone it hangs up in the "windows mobile direct push technology" screen. I tried without SD card and SIM but no luck. I have all my contacts inside and I need them. How can I fix the problem of my phone. Please help.
ONBL 1.10.0000
SPL 1.10.0000
GSM 2.79.90
OS 1.10.0.0
-aneesh
Click to expand...
Click to collapse
i don't think u can save ur contacts now
just hard reset ur device but all data will be lost.

How to do the hard reset? please tell me.
no way to save data?

Hi,
I searched google and got the method to hard reset.
-------------
To perform a hard reset (Full Reset) press and hold the left SOFT KEY and the right SOFT KEY, and at the same
time, use the stylus to press the RESET button at the middle left side of your device.
Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:
This operation will delete all your personal data, and reset
all settings to manufacturer default. Press Send to restore
manufacturer default, or press other keys to cancel.
Release now the two SOFT KEYs, and then press the TALK (Send) button
---------------------
But when I press the reset button phone restarted but nothing siplayed as mentioned above. Again it went to windows screen and hung there! Cant even do hard reset? What can I do now? Please hlep.

It is ok now. thanks

aneeshnr said:
It is ok now. thanks
Click to expand...
Click to collapse
its nice to hear that ur device is working .
enjoy!!

I was update my htc p3400i ROM, after completion. Phone turn off but not restart, if I try camera button and reset button only green and red right blink not any indication shown on screen,…please help me.
I shall very thankful, if you solve my problem
Sanmukh singh
MSL, Mumbai.

sanmukhsingh said:
I was update my htc p3400i ROM, after completion. Phone turn off but not restart, if I try camera button and reset button only green and red right blink not any indication shown on screen,…please help me.
I shall very thankful, if you solve my problem
Sanmukh singh
MSL, Mumbai.
Click to expand...
Click to collapse
which rom u have updated??????????

hi deepav84,
i was updating this rom "RUU_Gene_hTC_Asia_India_1.17.720.1_4.1.13.34_02.79.90_Ship" after 100% complete it turns off , but not start only Green and red light flash during press reset button...
i was try all methods,#remove batery 20 sec and then start with camer button & both camera and voice button, nothing shown in USB in PC. but result is same...
please help how i can recover my device.....

please help!! after ROM upgrade the device stuck completely!

please expert guys help ...
i have new leo with ROM 1.43 today after trying to upgrade to ROM 1.66 I did everything as asked, the installer began , with all the colours on the leo display then it started the percent completion counter , and after 2% it wrote me error something , and the leo restarted but stuck in the white start up menu with the green HTC icon and below the R G D information but the device doesnt proceed further and stuck here !!!
please help !!!!
o bought the device in europe , but i am from israel , htc sent me notification about new arabic ROM with link , i tried with my serial to download but couldnt , it wrote me "this upload not compatible with ur device" , i downloaded it from here XDA developers , but it went wrong !! , the problem that the phone stuck in the loader menu , before uploading the sense interface , and i have no connection between the pc and the phone "no active sync" so how can i reinstall the older version or make the phone load again ?!!?!! plz help !

I would recommend to do a hard reset in the first place and see if that helps.
I don't know how you did the upgrade and what the exact error message was, but you have always the option of installing HSPL and a custom ROM, as long as you can connect through USB - that is entering bootloader (the tri-color screen) and seeing "USB" at the bottom of the screen.
Similar cases have been discussed recently at http://forum.xda-developers.com/showthread.php?t=625363
Most important: do not lose hope, there's always a way

hello thanks for reply
how can i hard rest , the phone is not moving from the white menu ,which comes before the orange menu with the windows mobile icon , the buttons in this menu are not responding , is there any way to do hard rest using some phone hard keys , because i cant establish any connection with the pc , so i guess i need to do something with the phone itself ...?

fadiheno said:
how can i hard rest , the phone is not moving from the white menu ,which comes before the orange menu with the windows mobile icon , the buttons in this menu are not responding , is there any way to do hard rest using some phone hard keys , because i cant establish any connection with the pc , so i guess i need to do something with the phone itself ...?
Click to expand...
Click to collapse
Hi
Take the battery out for about 10 sec. Then Put the battery back. Press and hold Vol down and Vol up then press the power button grey screen will ask the confirmation to format internal memory. Then press vol up. Then vol up for reboot
I hope you understand. Good luck

how to press voume up and down ?
do u mean at the same time bith vol up and down or first up then down ?
thanks

Thread closed. Exact duplicate thread in HD General.
WB