One annoying feature of new Nook HD+ (and assuming Nook HD) is that during initial set up it will look for and force you to update (if one is found). There is a neat and really easy trick to bypass this process.
Once you get to that step in the process, during the process hold down the power button and force it to shut off by selecting "OK" in the prompt. You have to do it before it finishes downloading the update.
Once you power it back on you'll have to restart the whole process of entering your WiFi and information again. When you get to the point where the device looks for an update, it will look for a few seconds and determine that its got the latest version installed and proceed to the next phase.
To make sure you did it correctly just go into "Settings" and check the version. For me my default was 2.0.4, for you it may be different, but either way its not 2.0.5.
I've tested it multiple times and always with great success.
What about 2.0.4 do you prefer over 2.0.5?
Also, let us know if this actually stays on 2.0.4. Those of us who had already registered Nooks (both HD and HD+) when 2.0.5 came out got updated in spite of having turned off auto updates.
lkmiller said:
What about 2.0.4 do you prefer over 2.0.5?
Also, let us know if this actually stays on 2.0.4. Those of us who had already registered Nooks (both HD and HD+) when 2.0.5 came out got updated in spite of having turned off auto updates.
Click to expand...
Click to collapse
It was for rooting purposes, since at the time I couldn't find a rooting tool for 2.0.5, that's why. Also I too had registered once under 2.0.5, and when starting fresh found that this method does work regardless of what you initially registered under. Though it only buys you little time to do whatever modifications you need to to your device before it automatically updates you (you could also leave WiFi turned off too).
dcoke said:
It was for rooting purposes, since at the time I couldn't find a rooting tool for 2.0.5, that's why. Also I too had registered once under 2.0.5, and when starting fresh found that this method does work regardless of what you initially registered under. Though it only buys you little time to do whatever modifications you need to to your device before it automatically updates you (you could also leave WiFi turned off too).
Click to expand...
Click to collapse
What device are you running? Still would like your factory zip.
Sent with XDA Premium from my Nook HD+ running CM10 on SD
dcoke said:
It was for rooting purposes, since at the time I couldn't find a rooting tool for 2.0.5, that's why. Also I too had registered once under 2.0.5, and when starting fresh found that this method does work regardless of what you initially registered under. Though it only buys you little time to do whatever modifications you need to to your device before it automatically updates you (you could also leave WiFi turned off too).
Click to expand...
Click to collapse
Ok, I thought that might be why. Thankfully we can root 2.0.5 now. But it's good to know this method of postponing that initial update if I ever need to reset and start over.
nook hd+ auto-updated after leapinlar root+cwm fixes
My Nook HD+ notified me last night that it had auto-updated to 2.0.6 but I was able to get back my original Nova Prime Launcher and the Google Play store continues to work (it broke Beautiful Widgets, but uninstalling it and reinstalling it fixed that)
I had originally rooted it from 2.0.5 using the Universal Root method here: http://forum.xda-developers.com/showthread.php?t=2062613
I had the following images installed:
NookHD-HDplus-Gapps+Extras-for-stock-rev1.zip
NookHD-HDplus-Universal-Root-rev1.zip
NookHD-HDplus-LocationServices.zip
Using CWM for here:
NookHDplus-bootable-CWM-6023-for-emmc-stock-4GB-rev1.zip
Note - I did not manually update or in anyway 'induce' the update, it just happened. Did I miss something in the instructions to prevent auto-update?
Atleast the play store and Nova Launcher keeps working (not had time to check if root is still working though) But I did notice that the B&N Home launcher keeps showing up more often than before (hitting apps and going back brings back Nova)
Thanks
vtmanryn said:
My Nook HD+ notified me last night that it had auto-updated to 2.0.6 but I was able to get back my original Nova Prime Launcher and the Google Play store continues to work (it broke Beautiful Widgets, but uninstalling it and reinstalling it fixed that)
I had originally rooted it from 2.0.5 using the Universal Root method here: http://forum.xda-developers.com/showthread.php?t=2062613
I had the following images installed:
NookHD-HDplus-Gapps+Extras-for-stock-rev1.zip
NookHD-HDplus-Universal-Root-rev1.zip
NookHD-HDplus-LocationServices.zip
Using CWM for here:
NookHDplus-bootable-CWM-6023-for-emmc-stock-4GB-rev1.zip
Note - I did not manually update or in anyway 'induce' the update, it just happened. Did I miss something in the instructions to prevent auto-update?
Atleast the play store and Nova Launcher keeps working (not had time to check if root is still working though) But I did notice that the B&N Home launcher keeps showing up more often than before (hitting apps and going back brings back Nova)
Thanks
Click to expand...
Click to collapse
We have known for a while that setting the OTA to manual does not seem to stop auto updates anymore. The good news is that it still accepts the root. Just flash universal root again.
Sent with XDA Premium from my Nook HD+ running CM10 on SD
I might have found a way how to disable Nook HD OTA autoupdate feature.
For some reason setting com.bn.device.fota.mode to manual does not work, so there is more straight approach to solve this.
So far i have found two:
1) Once you have rooted your device it is just a matter of editing /etc/hosts file and adding couple of lines
127.0.0.1 nook.com
127.0.0.1 barnesandnoble.com
127.0.0.1 su.barnesandnoble.com
which effectively blocks access to autoupdates, but when you reboot your device, all your data will be erased (nook will restore itself to factory state). So some way around is needed.
2) There is an app on google store called "Android Firewall", install it. Once installed block Wifi for NookConnectivityService. GAPPS and browser will not be affected, you'll get norification "Wifi error". But otherwise wifi is fuctional.
2) There is an app on google store called "Android Firewall", install it. Once installed block Wifi for NookConnectivityService. GAPPS and browser will not be affected, you'll get norification "Wifi error". But otherwise wifi is fuctional.
Click to expand...
Click to collapse
Blocking NookConnectivityService kills connectivity to the Google Play.
greenya said:
1) Once you have rooted your device it is just a matter of editing /etc/hosts file and adding couple of lines
127.0.0.1 nook.com
127.0.0.1 barnesandnoble.com
127.0.0.1 su.barnesandnoble.com
which effectively blocks access to autoupdates, but when you reboot your device, all your data will be erased (nook will restore itself to factory state). So some way around is needed.
Click to expand...
Click to collapse
You can symlink the hosts file. See my HD/HD+ tips thread linked in my signature. Look at item 15. Of course there are othe ways to prevent the update, like symlinking build.prop and doing the white on white repair. But those just cause the update to fail, while this may prevent them even checking. If this works, I may update my CWM zip to include it.
EDIT: After researching this a little I have found an easy way to accomplish this. That is to use AdAway. You can safely use that program if you configure it to put the hosts file on /data. It automatically symlinks it for you. But you need to be rooted to use this app. And it has a feature where you can add your own sites to block. Just add those sites listed in the post above. Then every time AdAway updates its own list, it adds your list to it also. This will block B&N from using those sites to download their updates. But realize that it also blocks you from browsing their site.
Sent from my Nook HD+ running CM10.1 on Hybrid SD
leapinlar said:
EDIT: After researching this a little I have found an easy way to accomplish this. That is to use AdAway. You can safely use that program if you configure it to put the hosts file on /data. It automatically symlinks it for you. But you need to be rooted to use this app. And it has a feature where you can add your own sites to block. Just add those sites listed in the post above. Then every time AdAway updates its own list, it adds your list to it also. This will block B&N from using those sites to download their updates. But realize that it also blocks you from browsing their site.
Click to expand...
Click to collapse
Nice! It works then Including it to CWM zip is a good idea, with a warning, that you get to loose one site. That rooting thing imho is the whole reason for not using it, but substituting with google play.
BTW Is your hybrid cm10.1 stable on nook hd+ ?
greenya said:
Nice! It works then Including it to CWM zip is a good idea, with a warning, that you get to loose one site. That rooting thing imho is the whole reason for not using it, but substituting with google play.
BTW Is your hybrid cm10.1 stable on nook hd+ ?
Click to expand...
Click to collapse
WARNING! Hybrid not for HD+ !!!
greenya said:
BTW Is your hybrid cm10.1 stable on nook hd+ ?
Click to expand...
Click to collapse
My Hybrid setup on the HD+ is experimental and a hacked version by me. And I am running verygreen's 1-07 version of CM10.1. The Hybrid works great and is very stable, but the CM10.1 is buggy.
Sent from my Nook HD+ running CM10.1 on Hybrid SD
leapinlar said:
My Hybrid setup on the HD+ is experimental and a hacked version by me. And I am running verygreen's 1-07 version of CM10.1. The Hybrid works great and is very stable, but the CM10.1 is buggy.
Sent from my Nook HD+ running CM10.1 on Hybrid SD
Click to expand...
Click to collapse
Seems i missed somewhere something
datas0ft said:
Seems i missed somewhere something
Click to expand...
Click to collapse
You did not miss it. I just got it working this weekend and this is the first I have told anyone. I am going to test it a while before I even consider making it for anyone else. It does work but I had to manually configure some things. And it only works on CM10.1, not CM10. Until we get some better CM10.1's it does not really matter anyway.
Sent from my Nook HD+ running CM10.1 on Hybrid SD
leapinlar said:
You did not miss it. I just got it working this weekend and this is the first I have told anyone. I am going to test it a while before I even consider making it for anyone else. It does work but I had to manually configure some things. And it only works on CM10.1, not CM10. Until we get some better CM10.1's it does not really matter anyway.
Sent from my Nook HD+ running CM10.1 on Hybrid SD
Click to expand...
Click to collapse
This news change many things. But seems verygreen is so busy last time or found something new interesting.
Anyway. If you need some "hard testing" (when testing may make item dead) then ask me. I have one item with no warranty and ... you know, its not mine ... and its not last one.
greenya said:
I might have found a way how to disable Nook HD OTA autoupdate feature.
For some reason setting com.bn.device.fota.mode to manual does not work, so there is more straight approach to solve this.
So far i have found two:
1) Once you have rooted your device it is just a matter of editing /etc/hosts file and adding couple of lines
127.0.0.1 nook.com
127.0.0.1 barnesandnoble.com
127.0.0.1 su.barnesandnoble.com
which effectively blocks access to autoupdates, but when you reboot your device, all your data will be erased (nook will restore itself to factory state). So some way around is needed.
2) There is an app on google store called "Android Firewall", install it. Once installed block Wifi for NookConnectivityService. GAPPS and browser will not be affected, you'll get norification "Wifi error". But otherwise wifi is fuctional.
Click to expand...
Click to collapse
Thank you for this. It works. I added the manual way to do it via AdAway to my HD/HD+ Tips thread and added a CWM zip to my HD/HD+ CWM thread to automatically do it for you if you are not rooted. Both threads are linked in my signature.
Sent from my Nook HD+ running rooted stock
leapinlar said:
Thank you for this. It works. I added the manual way to do it via AdAway to my HD/HD+ Tips thread and added a CWM zip to my HD/HD+ CWM thread to automatically do it for you if you are not rooted. Both threads are linked in my signature.
Sent from my Nook HD+ running rooted stock
Click to expand...
Click to collapse
Could you also just freeze the NookConnectivityService app using Titanium Backup - seems to work for me
docfreed said:
Could you also just freeze the NookConnectivityService app using Titanium Backup - seems to work for me
Click to expand...
Click to collapse
Someone earlier says doing that blocked his Google Play. Is yours working ok?
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
Someone earlier says doing that blocked his Google Play. Is yours working ok?
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
If you mean the Play Store, yes no problem - I don't use any other Play apps (like music, books, etc.). I am on 2.06, rooted, ADW EX Launcher and see no issues whatsoever with WiFi (as a matter of fact, no issue signing in to BN.com and downloading one of my books.
Related
*NEW INSTRUCTIONS*
Today I figured out how to get Amazon Video On Demand app on my phone and watch videos
I did this with a rooted phone, I am not sure if you phone needs to be rooted to accomplish this task. I have attached the required files to accomplish this task. These steps are assuming you have a rooted phone.
REQUIREMENTS:
Download attached APKs
Wireless connectivity
VooDoo OTA for rooted phones (https://market.android.com/details?id=org.projectvoodoo.otarootkeeper)
INSTRUCTIONS:
1. Copy downloaded APKs to your phone
2. Install each APK and make sure to click DONE after each installs
3. Enable phones Wireless and connect via WiFi
4. Go to your phone SETTINGS>ACCOUNT AND SYNC
5. Press ADD ACCOUNT
6. Press AMAZON and enter your Amazon Prime credentials
7. Start the VooDoo OTA app
8. Press TEMP.UN-ROOT and allow the program to temporarily unroot your phone
9. Reboot your phone
10. When the phone comes up, still be attached via wireless and try your app
I hope this works for everyone who tries, please report your findings
Currently this app only works on wireless it will not work with your cell signal. I am looking to see if I can figure out how to enable the app to use the cell signal, I'm not a developer but I do have an idea to try!
ill try this on my Amaze 4G when i get home
I did all of these on my CM7 mod and "Watch Now" is still grayed out for me.
MoToKrusheR said:
I did all of these on my CM7 mod and "Watch Now" is still grayed out for me.
Click to expand...
Click to collapse
The only think I can say is that make sure the device is un-rooted and reboot after using the VooDoo OTA
You're just about there!
do you guys think this would work with the bionic?
elephant007 said:
The only think I can say is that make sure the device is un-rooted and reboot after using the VooDoo OTA
You're just about there!
Click to expand...
Click to collapse
I've done the reset 3 times, still a no go. Going to keep looking into it though.
MoToKrusheR said:
I've done the reset 3 times, still a no go. Going to keep looking into it though.
Click to expand...
Click to collapse
Are you doing this on a phone or on your Fire?
I wonder if you can remove root from some alternative method and see if you can run VOD, perhaps remove BurritoRoot if that's what you have installed.
There is something about CM7 that amazon does not like. I have never gotten it to work on CM7, even after temp unrooting. But if I did the same thing on a none cm7 rom, it worked fine. Go figure.
elephant007 said:
Are you doing this on a phone or on your Fire?
I wonder if you can remove root from some alternative method and see if you can run VOD, perhaps remove BurritoRoot if that's what you have installed.
Click to expand...
Click to collapse
It's on a fire. Before I flashed CM7 over, I was running just a rooted fire, and voodo ran just fine allowing amazon video to work when needed. Would be a shame if I couldn't get it to run on CM7.. not a huge loss, just would like to see if it could work on this variant..
That's too bad that it doesn't work on CM7
Maybe I should try it and see what I can find out
will try and post quick feed back
for those of you having problems running this one CW7, according to this link here http://forum.xda-developers.com/showthread.php?t=1390773 I'm guessing it's the MAC Address issue
Just a guess
elephant007 said:
for those of you having problems running this one CW7, according to this link here http://forum.xda-developers.com/showthread.php?t=1390773 I'm guessing it's the MAC Address issue
Just a guess
Click to expand...
Click to collapse
Wonder if an update.zip could be made for the CM7 variant in this thread?
MoToKrusheR said:
Wonder if an update.zip could be made for the CM7 variant in this thread?
Click to expand...
Click to collapse
EDIT - I flashed the updated/MAC address fix - No wipe ROM, but still a no go... Might have to do a full wipe/install?
This is the ROM: http://www.mediafire.com/?hmdc0lmgvnlbg97
Located in this thread - http://forum.xda-developers.com/showthread.php?t=1390773&highlight=mac
"If you're upgrading from an EXISTING CM7 install then use this ROM instead. This one will NOT wipe the cache and data partitions which should mean that you can upgrade from one version of CM7 to another without losing any of your existing date (or that's at least the idea)"
I tried this on my CM7 Kindle Didn't Work
I copied the apk's and ran the installs. It won't let me login to Amazon even. I just grabbed the apk's from the Kindle Fire .bin file though. I'll try the ones you have for download in your post and see if they work differently.
Hmm, MAC wasn't the problem
I'm on ICS and when I try to add an Amazon account I get a failure. I've checked my MAC and it's the same as under stock, but what does concern me is my serial number is all 0's.
Has anyone got this to work under ICS? Is everyone's serial number all 0's? Any other hints on how to get VOD working?
its working fine on my amaze 4g!
thedarksavant said:
I'm on ICS and when I try to add an Amazon account I get a failure. I've checked my MAC and it's the same as under stock, but what does concern me is my serial number is all 0's.
Has anyone got this to work under ICS? Is everyone's serial number all 0's? Any other hints on how to get VOD working?
Click to expand...
Click to collapse
Did you try logging into Amazon via WiFi?
"Parse error. There is a problem parsing the package" when install MyAccount-unsigned.apk. Any ideas?
Emerald214 said:
"Parse error. There is a problem parsing the package" when install MyAccount-unsigned.apk. Any ideas?
Click to expand...
Click to collapse
Redownload and try again, sounds like maybe it didn't download or get copied to your phone correctly
hey, I am new to the tablet world, I tried to search for this and look in the recent post and didnt really find the answer I was looking for....
So if I buy a new or refurbished Nook Color right now from B&N... will I be able to root it?!
this article is old... so I am not sure if this is the case?
any advice Please
WARNING - READ THIS FIRST: Barnes and Noble has introduced a new hardware revision which bricks your unit if you install their official 1.0.0 Firmware (A step needed to root). As of right now, Nooks with serial #s starting with 1003 (running firmware 1.5) cannot be rooted, and should NOT be attempted. See nookdevs New_Hardware_Revision for more details before you think of trying this!
Click to expand...
Click to collapse
from:
nooktalk.net/news/time-to-hack-root-your-nook
THANKS!
cant post the regular link yet
Just buy from eBay or Craigslist you'll find it cheaper n rootable
Sent from my NookColor using XDA Premium App
Well, where is the difference if I buy it new from eBay?! How is it more or less rootable...? If it is new it is new No matter where it comes from or?!
and 135$ for refurbished didn't seem bad... Or?!
Sent from my PC36100 using XDA App
First.... those may be Nooks and NOT Nook Colors... The newest firmware for Nook Color or Nook Tablets is 1.4.1 and you reference FW ver 1.5.
Also, I don't know of any NC's or NT's with serial numbers below 2000 first 4 digits.
Additionally, with the newer rooting tools available, you don't need to install anything prior to 1.4.1 to root them.
alexwick said:
[...] From:
nooktalk.net/news/time-to-hack-root-your-nook
Click to expand...
Click to collapse
At the very top of that article, it states:
Last Updated on Wednesday, 29 December 2010 12:54
You might find reading more recent articles a bit more revealing. A few things have happened since 2010.
I am aware the article is old... So short answer...
A new bought nook can be rooted?!?
Sent from my PC36100 using XDA App
Short answer, yes.
My base FW is 1.0.0. I'm running the 20120217 build of Mirage-Kang from eMMC.
I can't imagine how it could get much more rooted than this unless it would be to follow the directions to root it to the letter but if I did that then I wouldn't be much of an Asshole and I am a journeyman Asshole so there you have it.
Oh, and I don't feel terribly compelled to take it out of the case to look at the serial.
MISRy said:
Short answer, yes.
My base FW is 1.0.0. I'm running the 20120217 build of Mirage-Kang from eMMC.
I can't imagine how it could get much more rooted than this unless it would be to follow the directions to root it to the letter but if I did that then I wouldn't be much of an Asshole and I am a journeyman Asshole so there you have it.
Oh, and I don't feel terribly compelled to take it out of the case to look at the serial.
Click to expand...
Click to collapse
But do you have a Nook... or a Nook Color?
I mean yeah the Nook is rootable... but I didn't know a Mirage Kang was done for it.
Just ordered a refurbished nook color for 135$ hope will get it rooted fine... Which is the best thread for noobs here to get it rooted?!
Sent from my PC36100 using XDA App
alexwick said:
Just ordered a refurbished nook color for 135$ hope will get it rooted fine...
Click to expand...
Click to collapse
Since there is a manual nooter for the 1.4, there's no problem rooting it.
Which is the best thread for noobs here to get it rooted?!
Click to expand...
Click to collapse
Which rooting do you wish to do? If you want to run the stock B&N apps side by side with apps downloaded from the B&N market, then first register the refurbished system with B&N, then go to NC developer forum and look in "[NC][1.4.1] ManualNooter 5.02.19". That's a couple of minor version steps past the one I used, but it looked like its got it all pulled together from the three different sources of info I used last month.
I wanted to keep Nook Comics support in the stock ereader, so I opted for the manual nooter.
If you want to do a CM7/CM9/MIUI root, which installs alternate firmware for the system instead of modifying the existing firmware to allow Android market apps ... well then, I dunno, as after experimenting with a CM7 sd sidecard, I opted for the manual nooter approach. I'd look in the developer forum for the most recent thread with detailed install instructions for the firmware I wanted to install.
Pretty off topic, but this helped me when I needed to exchange a nook color that I had lost the box for. If you need your serial number, it is inside the flap that covers the micro SD slot.
There are other ways to find it, but if you are on the phone with support and a rooted nook, this is a useful thing.
I also just bought a refurb Nook Color. It is running 1.3.0 out of the box. I want to root it then install CM7. However I can't find any clear posts on how to. Either they are all for earlier FW or 1.4. Should I update to 1.4 before Nootering? If so which MNooter should I use? Or is it recommended to just Nooter 1.3? Again which Mnooter should I use for 1.3?
Thanks
BruceMcF said:
Since there is a manual nooter for the 1.4, there's no problem rooting it.
Which rooting do you wish to do? If you want to run the stock B&N apps side by side with apps downloaded from the B&N market, then first register the refurbished system with B&N, then go to NC developer forum and look in "[NC][1.4.1] ManualNooter 5.02.19". That's a couple of minor version steps past the one I used, but it looked like its got it all pulled together from the three different sources of info I used last month.
I wanted to keep Nook Comics support in the stock ereader, so I opted for the manual nooter.
If you want to do a CM7/CM9/MIUI root, which installs alternate firmware for the system instead of modifying the existing firmware to allow Android market apps ... well then, I dunno, as after experimenting with a CM7 sd sidecard, I opted for the manual nooter approach. I'd look in the developer forum for the most recent thread with detailed install instructions for the firmware I wanted to install.
Click to expand...
Click to collapse
Can I not install cm7 on the SD and the regular b&n system when boot from internal memory?!
Optimus V Prime said:
I also just bought a refurb Nook Color. It is running 1.3.0 out of the box. I want to root it then install CM7. However I can't find any clear posts on how to. Either they are all for earlier FW or 1.4. Should I update to 1.4 before Nootering? If so which MNooter should I use? Or is it recommended to just Nooter 1.3? Again which Mnooter should I use for 1.3?
Click to expand...
Click to collapse
You do not need to root the B&N firmware before loading CM7. You do need to decide whether you want to run CM7 on internal eMMC or external SD. If you plan to install CM7 to eMMC, you will over-write the B&N firmware, so rooting it is pointless. Once you've decided that, we can point you in the right direction.
There are also guides here on rooting B&N firmware that you can locate with a bit of searching.
---------- Post added at 03:18 PM ---------- Previous post was at 03:14 PM ----------
alexwick said:
Can I not install cm7 on the SD and the regular b&n system when boot from internal memory?!
Click to expand...
Click to collapse
Yes, you can.
alexwick said:
Can I not install cm7 on the SD and the regular b&n system when boot from internal memory?!
Click to expand...
Click to collapse
Yes, as I said, that's the setup I was using when I decided I prefer a manual nooter. Among your choices, you can:
(1) Replace the stock firmware with an alternative, such as CM7
(2) Run CM7 off a booting SD card and run stock B&N from internal memory
(3) Root the stock B&N system and then load and run Android market apps alongside the B&N built-in and B&N store apps.
I wanted to keep the features of the 1.4.1 ereader, including Nook Comics support, so for me (1) was out, and I only needed a few apps from the Android Store, so I finally settled on (3) to avoid having to boot back and forth between the two systems. But first I did (2) to try things out and get an idea of whether I wanted to root the B&N firmware or replace it with something like CM7.
Can I not install cm7 on the SD and the regular b&n system when boot from internal memory?!
Yes, as I said, that's the setup I was using when I decided I prefer a manual nooter. Among your choices, you can:
(1) Replace the stock firmware with an alternative, such as CM7
(2) Run CM7 off a booting SD card and run stock B&N from internal memory
(3) Root the stock B&N system and then load and run Android market apps alongside the B&N built-in and B&N store apps.
I wanted to keep the features of the 1.4.1 ereader, including Nook Comics support, so for me (1) was out, and I only needed a few apps from the Android Store, so I finally settled on (3) to avoid having to boot back and forth between the two systems. But first I did (2) to try things out and get an idea of whether I wanted to root the B&N firmware or replace it with something like CM7.
Click to expand...
Click to collapse
It think I wanna go for option 2&3, can I not root the B&N internal system and also run CM 7 from SD card?
Do I have to take the SD card in and out depending in which one i wanna boot!?
Also another question... The whole reason this rooting is done if I understand correctly is to have access to all the systems in the NC, where do I get the Apps from ? Do I still have to get them through the market? Or can I download them somewhere!?
Got a question... Git my nook today, and it seems to be lagging quite a bit sometimes... Is that normal? Sometimes tottaly unresponsive... Is this normal?!
Sent from my PC36100 using XDA App
alexwick said:
It think I wanna go for option 2&3, can I not root the B&N internal system and also run CM 7 from SD card?
Do I have to take the SD card in and out depending in which one i wanna boot!?
Click to expand...
Click to collapse
Taking the SD card in and out depending on which one I wanted to boot, then full power off and power on was the way I did it. Don't know if there's a better way, but never saw a better way mentioned.
You can indeed run CM7 from an SD card and root the B&N internal system. That would allow you to use Nook Tweaks in the CM7 side to, for example, run a keyboard off the USB port and overclock the chip ~ neither of which you can do with the stock kernel ~ and still have the use of the 1.4.1 ereader for Nook Comics or media-enhanced ebooks.
Get a main microSD card for the CM7 SD card install. Follow the CM7 SD card instructions to do the CM7 SD card install on the big card.
And then get another microSD card (2GB Class 4 is plenty) and follow the 1.4.1 manual nooter instructions to root the stock B&N kernel.
Also another question... The whole reason this rooting is done if I understand correctly is to have access to all the systems in the NC, where do I get the Apps from ? Do I still have to get them through the market? Or can I download them somewhere!?
Click to expand...
Click to collapse
If you follow the CM7 SD card install directions, you will have access to the full Android Market on that install. Same thing if you follow the 1.4.1 manual nooter instructions ~ you will have access to the Android Market via the Nook Color Application Manager, and if you want can put the Android Market on the B&N Home Screen.
Its best to have a gmail.com account already, for the Android market registration, so sign up for one of those before starting the process if you don't already have one. And from the Android Market, you can also install the other markets (Amazon, 1mobile, GetJar) if you prefer one of those.
alexwick said:
Got a question... Git my nook today, and it seems to be lagging quite a bit sometimes... Is that normal? Sometimes tottaly unresponsive... Is this normal?!
Click to expand...
Click to collapse
It can be laggy, especially if you have too much load on it. Sometimes I'm surprised at how many windows I have open in the stock browser. Turning it all the way off will shut down apps that you may have left unclosed, free up RAM, and its normally back to its normal self.
Mind, the gurus have Android apps that can be used to shut down individual apps, but the brute force approach seems to work for me.
thanks for the quick detailed reply...
for the LAGS, well I dont have hardly anything open... the only thing i installed and bought was from the market. Angry Birds... and it seems sometime it will not respond to the throwing of the bird, but just scale the screen... even to exit the game and after the game is closed it seems to not respond properly... having to tap a button 5 times until it responds... and than it works fine after a reboot... and than a couple hours later same thing in the game... ..
also it seems like internetpages like nick.com seem to load forever and are very laggy. I ahve a 10 MBIT Internet connectio over wifi, so that shouldnt be a problem....
To teh dual Systems...Do I also need a second 2GB card for the rooted internal stock system, or is that just for the installation of it!?
I actually do have a 16 GB and a 2 GB at home already...
"If you follow the CM7 SD card install directions, you will have access to the full Android Market on that install. Same thing if you follow the 1.4.1 manual nooter instructions ~ you will have access to the Android Market via the Nook Color Application Manager, and if you want can put the Android Market on the B&N Home Screen."
Click to expand...
Click to collapse
Well on my android phone... most of the apps are available I believe for free on the forums... is this similar here... or do I have to buy them!? BTW My phone is not rooted...
The System is some 1.3 version I received... will I need to update to 1.4 first!?
I also do already have a gmail account... its a german one though [email protected] but that should be fine ... It is the german GMAIL
Also linked the nook to th BN Store I believe...Is tehre any waay to check?!
Should I not be able to stream netflix... with the regular nook!?
ONCE AGAIN THANKS FOR YOUR TIME !!!!
alexwick said:
... also it seems like internetpages like nick.com seem to load forever and are very laggy. I ahve a 10 MBIT Internet connectio over wifi, so that shouldnt be a problem....
Click to expand...
Click to collapse
That's just the stock Android Browser and an 800MHz single core system with 512Mb RAM plowing through a site with all the bells and whistles and targetted at a PC. Try the Dolphin HD browser (its in the B&N store, and its free so no worry about having to re-download it from the Android market to your CM7 install) ... it has an option to hold off flash content until you actually want to run it that can really speed up some sites.
To teh dual Systems...Do I also need a second 2GB card for the rooted internal stock system, or is that just for the installation of it!?
I actually do have a 16 GB and a 2 GB at home already...
Click to expand...
Click to collapse
Installation ... you want a good sized card for the CM7 install, and reading and storing an image from a large card, then formatting it and writing the install card image, then saving the install card image, formatting, and restoring the CM7 install image is a royal pain.
Note that you probably want to keep the install card as a bootable recovery card. 1GB is enough to do the manual noot, but 2GB is enough to hold the recovery of the original stock B&N before you do the manual root. 4GB is even better, as it can hold a recovery of the stock B&N as well as a recovery of the system right after it is manually nooted, in case you do something later to get it messed up.
And you can get a 4GB Class 4 card for $5 with free shipping from Amazon ~ the new 32GB flash cards have pushed the price of the smaller ones way down ~ so to my mind that's worth it to be able to set aside a recovery card.
Well on my android phone... most of the apps are available I believe for free on the forums... is this similar here... or do I have to buy them!? BTW My phone is not rooted...
Click to expand...
Click to collapse
Yes. There are paid apps, but both the CM7 install or the manual nooter give full access to a wide range of free apps on the main Android Market, and allow you to install 1mobile, GetJar, or Amazon if you prefer any of those markets.
The System is some 1.3 version I received... will I need to update to 1.4 first!?
Click to expand...
Click to collapse
Not for the SD card install of CM7. Be sure to follow the instructions for making an SD card install on a 1.3 system.
You'll want to upgrade for a rooted stock B&N Kernel to 1.4.2, because its only 1.4 that has the updated ereader, Nook Color tailored Netflix app, likely B&N Store HuluPlus this Friday ... if you were replacing the stock Kernel, there's be no reason to update, and the installs for the 1.3 system are more mature ... but if you want to keep the B&N Kernel, upgrade to 1.4.2. before you lock it down from further OTA updates.
I also do already have a gmail account... its a german one though [email protected] but that should be fine ... It is the german GMAIL
Click to expand...
Click to collapse
I'd don't know from personal experience, but I've seen some warnings about it being best to have a gmail.com account. Just to be safe, I'd sign up for a gmail.com account and give your primary gmail account as the email account used to confirm that you are a real person. Save it in an "Accounts" folder in your main gmail if you are unlikely to use it for anything except the Android market.
Also linked the nook to th BN Store I believe...Is tehre any waay to check?!
Should I not be able to stream netflix... with the regular nook!?
ONCE AGAIN THANKS FOR YOUR TIME !!!!
Click to expand...
Click to collapse
Before you start working on the unit, go to the store (its on the navbar) search for apps and download a free app. Dolphin HD is a good one. If it downloads and installs, you are linked to the B&N store.
I was thinking of making a custom rooting script for CWM (probably wouldn't release it), and I mostly want it to have a very small footprint and still have it feel like an unmodified Nook. I've mostly been using CM7 from an SD and haven't dealt with the stock OS much, but lately I've been using it more and I just like the way it's set up for some reason. I rooted it last night, but quickly reverted back after finding most apps 'weren't compatible with my Nook,' surprisingly including Nook Tweaks (I'll admit I was in a bit of a rush and wanted to get back to reading my book, otherwise I probably would have experimented more ). I also found that the apps installed with the root didn't show up in the stock launcher, and I'm not sure if that can be changed, or if it's already like that and I just needed to install an app from the Play Store and it would show up. Oh, and is there a manual root tutorial for 1.4.2 I can base my script on? Otherwise I'm just going to pull some stuff from my script for the Nook Simple Touch and ManualNooter.
You can add non-B&N apps to the B&N home screen using Nook Color App Manager. ManualNooter is pretty lightweight, and would be a good starting point for rooting the NC. I ran B&N 1.4.2 for months using it, and it worked very much as you describe.
Thanks! Only one problem, the Play store won't let me install it for some reason just like Nook Tweaks... How would I fix that?
Edit: And magically, it works now and I can install anything. Huh.
After many hours of reading and searching these forums for answers to various questions I had when rooting my new nook, I decided to write out all the answers the average user (like me) will wish he had known before he started. So here you go, I present all you need to know about rooting and configuring your nook from the box to the promised land of awesomeness.
This is for the Nook Simple Touch (also called NST, N2E) non-glowlight version. After you root your nook, the software advice should be the same, but if you have a glowlight version, see the post by ladykayaker below. http://forum.xda-developers.com/showpost.php?p=36035695&postcount=2
A. Rooting
1) Backing up
--- noogie.img
--- nookmanager
--- reclaiming and reformatting your micro sd after using winimage.
2) Firmware version
--- does version matter?
--- updates
3) Touchnooter
B. First Configuration
--- what to expect
--- getting google play and web browsing to work.
--- installing apps from micro sd
C. Make it awesome
--- apps you'll need to patch missing nook functions
--- Multi-touch, fast ink modes, and kernal mods
--- Battery
D. Phone specific apps
--- whatsapp, and getting an IMEI on your nook
--- Phone contacts
E. List of current unsolved problems
--- Media scanner
--- scrolling
--- keyboards
--- video support in certain apps
--- audio
A. Rooting
Part 1. Backing up.
Q: Can I get my device back to stock?
A: Yes, if you take backups before you start.
Step 1. Take your nook out of the box
Step 2. Register for a barnes and noble account
Step 3. http://forum.xda-developers.com/showthread.php?t=1142983
--- Noogie.img full partition backups ---
In English, this means you have to download noogie.img, and download winimage and use it to (CAREFULLY) write the image to a micro sd card. Boot your nook with the micro sd card. Then use winimage again to copy the physical disk (1.8gb) to a file. Now you can always go back to your stock nook, apparently.
--- Easy Backups and Restoring with Nook Manager ---
You can never be too safe. I suggest you backup with 2 methods.
Search "nookmanager for 1.21 and beyond".
Download nookmanager and write it to a micro sd card just like you did for noogie. Nook manager has a brilliant backup and restore feature and works on all versions, so boot into it and follow the menu to take a backup, it creates a second backup partition on your micro sd. So when you're done, plug in your nook and copy the backup file off and the md5 hash. Follow the previous step to reclaim your micro sd.
--- Reclaiming Your Micro SD ---
To reclaim your micro sd, on windows click start menu, search partition, and open the partition manager. Find your micro sd card which now has a small partition on it, select the partition, and delete it. Right click >> create simple partition >> fat32
Backup(s) finished.
2. Firmware
--- Firmware Version ---
Q: Does firmware version matter?
A: Yes it does, make sure you search for 1.1 update and update your version to 1.1 before rooting with touchnooter. Don't bother with 1.21 yet because all the cool things you've seen and want are done with 1.1 and 1.21 root needs more time to mature and become more user friendly (noob friendly).
To check your firmware version go into settings > device info.
--- updates ---
Q: How do I update to 1.1?
First check your firmware version, if it's 1.0.1, update to 1.1 by downloading the 1.1 firmware (it's a zip file) and moving it into the nook drive on your computer. It will update automatically. Don't wait too long to backup or move to 1.1 because it might automatically update to 1.21. You should update to 1.1 and root immediately. If your device came with 1.2, try this to flash and install 1.1: http://forum.xda-developers.com/showthread.php?t=1475613
--- touchnooter ----
Once you're on 1.1, download touchnooter and like noogie and nookmanager, make an image on your microsd with winimage and boot the device. the screen will turn black, and then you can take the card out and reboot. However, I found that after running the root once, many /most of the applications didn't function, I had to boot three times with touchnooter for most apps to work. It doesn't hurt so just do it if you have any problems.
B. First Configurations
--- What To Expect ---
Now that you're rooted and running in android, you're probably thinking, "well this sucks, the web browsers don't work and neither do the app stores...."
Calm yourself, it will get better.
--- Getting GAPPS and web browsing ---
Add a google account in gmail, sync it, sign into the same google account with youtube (nobody knows why). Then you will have to "wait a day" for it to work...
Q: Wait a day? FUUUUUU
A: Just joking, you can add another google mail account and sync that, your google play will now work without the wait, but it can be a bit tricky to hit the agree to tos button.
Reclaim your micro sd, you'll need it to install apps if your Opera Mini isn't working.
Search google for opera mobile, download the apk onto your micro sd, it's on opera's website, you should also download opera mini so you can re-install the one that comes loaded if it doesn't work. Rooting several times fixed my opera mini, but if yours is broken re-installing should fix it.
--- installing apps from micro sd ---
Q: How to install apps from micro sd?
A: Find the super manager, open it up, click the button to grant super user privileges, on the second or third tab from the left there is a file manager. Go into it, click the apk, click install.
C. MAKE IT AWESOME
Now that you have opera mini/mobile, can browse the web and google play works, what next?
--- apps you'll need to patch NST broken functions ---
1. Google play search function is broken, before you can start installing apps quickly, use opera mini to search for "search market" , you'll find the google play link, click it, install it.
2. default android home screen looks bad and custom wallpaper support is broken.
Now you probably want a decent looking home screen because face it, adk looks like crap, and you probably noticed you can't set the wallpaper because the media scanner doesn't detect any media = empty gallery = can't select a wallpaper.
use search market to find legacy launcher, install it
search for "wallpaper changer" and "es file explorer", install them. You can now set the wallpaper to any file on your sd card, and your android launcher looks great. Try adusting the font size in settings and adding widgets later.
3. Gallery doesn't work because media scanner is broken.
Some apps require the gallery to work to select images.
Your solution is to download the app "Quickpic" - it will allow you to choose pictures in apps that need a gallery.
4. The default keyboard is not very good, and the nook disables all spelling suggestion bars from keyboards. This makes t9 and chinese input impossible, and can make typing a pain in any language. The solution is to download a back-port keyboard.
Jellybean keyboard is a good back-port, search and install it, it's fully functional with lots of languages. No t9 though
1/2 OF GUIDE. CONTINUED IN MY NEXT POST
notes for Nook Simple Touch with Glowlight
If you have the US Nook with glowlight, firmware version 1.1.5, then follow these instructions :
backup
http://blog.the-ebook-reader.com/20...-and-restore-nook-glow-and-nook-simple-touch/
root
http://blog.the-ebook-reader.com/20...using-glownooter-includes-googles-app-market/
2/2 OF GUIDE.
--- Kernel, fast ink modes, and multitouch---
If you want multi touch and fast ink, search for oc kernel 1.66 with fastmode. it includes all you need for multitouch and overclocks the cpu. slightly.
FYI: You will need something called "Clockwork mod" or CWM to install the kernel. Google it, you'll need to image it to your micro sd just like you did for noogie.img. After you're done, copy the oc kernel zip file into the root directory, boot up your nook with the CWM sd inserted and follow the instructions to install package from zip.
Fast ink options:
Fast mode vs no refresh
fast mode is highly dithered, and as a result small text is unreadable. however it affects the system wide and it doesn't have any compatibility issues. No refresh is high contrast, low dithering means low dynamic range but text is very readable and sharp. The disadvantage is it seemed very buggy and it's application specific, ie- you have to enable it in each application and it gets a bit buggy or laggy when it switches on and off. It has a lot more configuration potential than fast mode though. I prefer fast mode because it's simple, and very fast. It just works.
--- Battery ---
You'll notice your battery suck as soon as you root. This isn't widely discussed, but it turns out it's do to certain phone system resources being active. This can eat up 10 times more battery than your screen, and a hundred times more than anything else, even using fast mode liberally. Go into file manager and rename /system/app/phone.apk and telephonyprovider.apk. Reboot immediately.
I suggest you also download the app "deep sleep" as well. Battery manager plus is also a good application to keep track of applications individual battery useage.
D. Phone Specific APPS
Q: I want whatsapp
You need to install a static IMEI, google imei nook touch xda and you'll find the thread. Download the exe, install it.
On your phone use search market to install "wifi adb" in wifi adb select on, note the ip address.
Run the imei app you got from xda dev and it will give you a static imei.
install the latest version of whatsapp. You'll notice you can't message anyone or add contacts because nook contacts doesn't work.
download go contacts ex and it will be ok.
E. Current major issues to consider and how to fix them:
--- Scrolling: ---
problem: Scrolling does not work properly, if you use chat programs, or google voice etc. you'll find yourself scrolling through the conversation manually every time. Some apps have difficulty scrolling at all.
Solution: No known fix at this time
--- Media scanner (media storage) ---
Problem: Media scanner fails to add media files from sd card into the media database. This means the default gallery and music applications won't detect any media.
Solution: No known direct solution, although you can edit the db manually using sql.
A better solution is to download an application which includes it's own embedded media search function. An example being quickpic as a gallery replacement.
--- Keyboards ---
problem: Keyboards are missing the text suggestion bar, this means that t9 input and language input like chinese are difficult/impossible.
Solution: Download a back-ported keyboard. Jellybean keyboard is by far the best, have extensive mutli-language support, and the text suggestion bars displays properly. The only downside is it does not have a t9 layout. Baidu, sougou, or any chinese t9 keyboard software will not work on the nook until the proper dependencies/support is patched somehow.
---video support ---
Q: Can I play video?
You can, but you'll be limited to about 10-15 fps with no audio and it will be 1 bit dithered. Download rockplayer to play various video formats. There appears to be a problem with hardware video decoding and only software video players work at the moment. If I discover a fix for broader video support I'll update this.
--- audio ---
Q: Can I play audio?
A: There are some people working on audio implementation through usb host and a cheap 2 or 3 dollar dongle. However, it seems like it's very 'alpha' at the moment, until someone writes an app to automatically configure audio through usb hosts, you can probably forget about it unfortunately.
I'll update this later.
Hi nice so far
You say " make sure you search for 1.1 update and update your version to 1.1 before rooting with touchnooter. Don't bother with 1.21 yet because all the cool things you've seen and want are done with 1.1"
But what if you bought your device lately and it already came with FW 1.2.0 then what do you do?
180 people read this thread and only 6 bothered to click on thanks?? Come on guys!
bentwand said:
But what if you bought your device lately and it already came with FW 1.2.0 then what do you do?
Click to expand...
Click to collapse
+1
Sent from my GT-N7000 using xda premium
apap said:
+1
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
I used this
forum.xda-developers.com/showthread.php?t=1475613
fosselman said:
I used this
forum.xda-developers.com/showthread.php?t=1475613
Click to expand...
Click to collapse
Thanks for the input, did your device come loaded with 1.2 or was it the result of an automatic update? I updated my guide with a link to touch-formatter.
jun127 said:
Thanks for the input, did your device come loaded with 1.2 or was it the result of an automatic update? I updated my guide with a link to touch-formatter.
Click to expand...
Click to collapse
Mine was on 1.0.x and I manually updated to 1.2.0 and then found out about rooting and wanted gapps so I downgraded to 1.1.0.
bentwand said:
But what if you bought your device lately and it already came with FW 1.2.0 then what do you do?
Click to expand...
Click to collapse
fosselman said:
I used this
forum.xda-developers.com/showthread.php?t=1475613
Click to expand...
Click to collapse
I bricked my new 1.2.0 device and the thread in the link above saved my butt. That said, it convinced my NSTG that it was a standard Simple Touch (no more glowlight function). I've been looking around for an update to NSTG 1.5 firmware to start over with, hoping the light features will come back. If any of you old salts can let me know if that's even possible I'd appreciate it.
If you're still at 1.2, this thread looks promising: http://forum.xda-developers.com/showthread.php?t=1675706&highlight=nstg&page=12
Looking at the ;ast pages of the NookManager rooting process it appears that the Amazon App store is US based and doesn't work for UK users (for example). Is there any simple method to fix that so it works outside of the US?
(Post i'm referring to - http://forum.xda-developers.com/showpost.php?p=36210882&postcount=110)
Thanks for clearing up the fastMode/noRefresh situation!
I have rooted NST by NookManager. The first step after that was to register device in DeviceRegistrator.apk. Next I installed ale stuff (gapps, amazon ect.) If I decide to flash kernel, it will be necessary to do it again?
Thanks, very in-dept
Renaming Phone.apk and TelephonyProvider.apk to avoid battery drain didn't work for me. I had to delete both and reboot. Now I can use my nook without losing too much battery
Used Total Commander app as my file manager to access /system/app/
Do you have a recommendation for a launcher other than ReLaunch?
dalovar said:
Renaming Phone.apk and TelephonyProvider.apk to avoid battery drain didn't work. I had to delete both and reboot. Now I can use my nook without losing too much battery
Used Total Commander app as my file manager to access /system/app/
Do you have a recommendation for a launcher other than ReLaunch?
Click to expand...
Click to collapse
I use lightning launcher it is lite weight and works well for me.
dalovar said:
Renaming Phone.apk and TelephonyProvider.apk to avoid battery drain didn't work for me. I had to delete both and reboot. Now I can use my nook without losing too much battery
Used Total Commander app as my file manager to access /system/app/
Do you have a recommendation for a launcher other than ReLaunch?
Click to expand...
Click to collapse
I've used ADW Launcher EX for years, and still loving it. Best customizability on any Nook Touch-compatible launcher, at least in my opinion.
Guys after successfully rooting my device and using it for some time it occurred to me that I would spend the $5 gift that comes with every NST. After buying books on B&N and turning on my nook I realized that nook's original software can't connect to the internet even when connected to my home's wifi connection.
I get the error: "Sorry, a problem has occurred. Please try again" in both the B&N library or B&N's shop.
Has anyone been able to download/sync books from B&N AFTER rooting your device?
Is this just a problem that I'm experiencing?
Thank you
dalovar said:
Guys after successfully rooting my device and using it for some time it occurred to me that I would spend the $5 gift that comes with every NST. After buying books on B&N and turning on my nook I realized that nook's original software can't connect to the internet even when connected to my home's wifi connection.
I get the error: "Sorry, a problem has occurred. Please try again" in both the B&N library or B&N's shop.
Has anyone been able to download/sync books from B&N AFTER rooting your device?
Is this just a problem that I'm experiencing?
Thank you
Click to expand...
Click to collapse
"Can't connect to the internet" at all or just to the B&N sites? If you've disabled/deleted some of the B&N apps you could have problems of this sort. There are all kinds of unlikely dependencies in the B&N system that can break functionality if something is missing.
I'm working with a rooted and modified NST running FW 1.21 and the only limitation I've seen so far is not being able to connect in-store (but I intentionally altered the QuickNav buttons to eliminate "Shop"). I haven't purchased books from B&N but have selected "Free Friday" offerings from the website and they come right down to my NST when it's online, no problem.
I assume you had no problem registering your device, otherwise I would suggest that maybe that error was due to B&N blacklisting the serial number. That's happened before with used/refurbished devices. Then a phone call is in order to B&N to get them to reverse that.
nmyshkin said:
"Can't connect to the internet" at all or just to the B&N sites? If you've disabled/deleted some of the B&N apps you could have problems of this sort. There are all kinds of unlikely dependencies in the B&N system that can break functionality if something is missing.
I'm working with a rooted and modified NST running FW 1.21 and the only limitation I've seen so far is not being able to connect in-store (but I intentionally altered the QuickNav buttons to eliminate "Shop"). I haven't purchased books from B&N but have selected "Free Friday" offerings from the website and they come right down to my NST when it's online, no problem.
I assume you had no problem registering your device, otherwise I would suggest that maybe that error was due to B&N blacklisting the serial number. That's happened before with used/refurbished devices. Then a phone call is in order to B&N to get them to reverse that.
Click to expand...
Click to collapse
Can't connect to B&N only. The rest of the internet is accessible. I can install apps from Google play from my computer to my device without problem too. The only system apps that i remember deleting are android apps (Phone.apk and TelephonyProvider.apk).
I don't think my serial number is black listed, because I was able to register my nook without problem. But is there any tool online where I could check my serial # statues that would be nice. I'm thinking of resetting to factory settings and rooting again if necessary. thanks for your help
dalovar said:
Can't connect to B&N only. The rest of the internet is accessible. I can install apps from Google play from my computer to my device without problem too. The only system apps that i remember deleting are android apps (Phone.apk and TelephonyProvider.apk).
I don't think my serial number is black listed, because I was able to register my nook without problem. But is there any tool online where I could check my serial # statues that would be nice. I'm thinking of resetting to factory settings and rooting again if necessary. thanks for your help
Click to expand...
Click to collapse
I have both of those apps disabled (.apk --> .OLD) so that's probably not it. To my knowledge there is no on-line way to check on the status of your serial number and now that I come to think of it, if you had no problem registering when you set up your Nook before rooting, there should be no problem with the serial number.
Seems like there was a post similar to yours not too long ago and going back to factory and rooting again fixed the problem, as much of a nuisance as that is. The only other thing that comes to mind is: you're not in the UK are you? Someone else posted a similar problem and it turned out that he needed a UK firmware update to account for changing B&N-UK URLs before he could connect.
If you get the problem sorted, I can't emphasize enough the importance--and convenience--of making a backup with NM. Backup early and often, especially when trying out something new. It saves so much time and hassle in the long run. But first....you need to get it in working condition
I would love to be able to sideload applications after 2.1.0 update. Root is working fine.
Royaltiger said:
I would love to be able to sideload applications after 2.1.0 update. Root is working fine.
Click to expand...
Click to collapse
You can if you flash my extras zip.
Sent from my rooted stock Nook HD
You are DA MAN!
parsing problem
Royaltiger said:
You are DA MAN!
Click to expand...
Click to collapse
I have installed the extras zip and was able to install amazon app store. I still cannot sideload many apps and get the 'there is a problem parsing the package' message. Basically, I downloaded the apk and used package installer and got this message.
Thanks for your help
PeeAm
peeam said:
I have installed the extras zip and was able to install amazon app store. I still cannot sideload many apps and get the 'there is a problem parsing the package' message. Basically, I downloaded the apk and used package installer and got this message.
Thanks for your help
PeeAm
Click to expand...
Click to collapse
Do you think rooting the tablet will help you?
Flashing to allow unknown sources via the image disk worked great for me. Adobe Flash and all my other non market installed apps working great. I did not root.
Edit:
Changed post from permissions to unknown sources.
rushless said:
Flashing permissions via the image disk worked great for me. Adobe Flash and all my other non market installed apps working great. I did not root.
Click to expand...
Click to collapse
Can you please elaborate on "Flashing permissions via the image disk". Which file to flash? Can you please link to the thread that has this file.
Thanks!
fljoe said:
Can you please elaborate on "Flashing permissions via the image disk". Which file to flash? Can you please link to the thread that has this file.
Thanks!
Click to expand...
Click to collapse
It is not a file to flash, his terminology is a little off. He means going to CWM and the advanced menu and choose 'fix permissions'.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
It is not a file to flash, his terminology is a little off. He means going to CWM and the advanced menu and choose 'fix permissions'.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
I tried 'fix permissions' but no success. I am trying to install widely used apps from travel sites like Orbitz and Travelocity which are installed on my samsung 7+ tab running ICS. It must have something to do with stock as they were installed on CM 10 on nook hd+. While I prefer stock due to the excellent sleep option and battery life, I may have to go back to CM 10.
PeeAm
leapinlar said:
It is not a file to flash, his terminology is a little off. He means going to CWM and the advanced menu and choose 'fix permissions'.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
It probably is a terminology issue, but what I did was:
1. Create the image with a micro sd.
2. Drap the Rev3 zip to the sd
3. Shut off the Nook
4. Insert the sd into the Nook and then turned it on
5. Went to the option to flash via the sd card with volume and pressed home key
6. Chose the Rev3 zip and pressed home. The files installed,
7. Removed the sd
8. Restarted..... Hung on the Nook screen for ten minutes, so held power to turn off
9. Restarted
10. Was able to side load all of my apps that needed it after that. I started with Adobe Flash which works GREAT with Dolphin, Opera and Xscope (had to side load Xscope, since could not install via market).
I do not recall flagging permissions in the image menu. I thought the flash process did all that, which it apparently did for me.
Side loaded Flash, Oid emulators, aFBA, Xscope and some market games as well that could be saved with an unrooted back-up app.
peeam said:
I tried 'fix permissions' but no success. I am trying to install widely used apps from travel sites like Orbitz and Travelocity which are installed on my samsung 7+ tab running ICS. It must have something to do with stock as they were installed on CM 10 on nook hd+. While I prefer stock due to the excellent sleep option and battery life, I may have to go back to CM 10.
PeeAm
Click to expand...
Click to collapse
His terminology was mixed up. He did not mean "fix permissions" either. He meant flashing the Extras zip, which enables unknown sources, not "flash permissions". But you had already done that.
So I don't know how to fix your problem.
Sent from my Nook HD+ running CM10.1 on emmc.
Yep, to me getting unknown sources working is a permission, but wrong in the true Android terminology.
Regardless, being able to install by side loading and the 2.1 update make this one of the best tablets. Actually, it seems a direct equal to the Excite 7.7 which IMO is the best current overall tablet. Better in some regards. The display and power efficiency in sleep mode is a big part of the departuresweight for the HD+.
Thanks, All is Well !
leapinlar said:
His terminology was mixed up. He did not mean "fix permissions" either. He meant flashing the Extras zip, which enables unknown sources, not "flash permissions". But you had already done that.
So I don't know how to fix your problem.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Leapinlar- you have been wonderful with your work on this tablet . Your note made me realize that may be there is something wrong with the apk files I had copied from my other tablet. After spending many hours searching on google for sites that were not merely links to google play, I downloaded the apk files I needed. All of them installed perfectly !
Thanks once again to you,verygreen and bokbokan for making nook tablet the best tablet out there.
kind regards
PeeAm
Leap, rocks!
May be not the right place to ask, if that I am sorry. Anyway, by flashing extra.zip, will it help with host USB on the nook hd+?
TIA
samteee said:
May be not the right place to ask, if that I am sorry. Anyway, by flashing extra.zip, will it help with host USB on the nook hd+?
TIA
Click to expand...
Click to collapse
No, it has nothing to do with that.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
No, it has nothing to do with that.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Hello, I followed your tutorial to the exact letter and all I got was my nook restarting several times before finally wiping itself and having to do the whole set up process again. I formatted the card and set the card to active like instructed. But which rar do I need? I am running the nook hd with 2.1.0. Software. I tried all the nook hd bootfiles rars listed and added the zip I wanted to install and it keeps rebooting and wiping.
Thanks
pmdash said:
Hello, I followed your tutorial to the exact letter and all I got was my nook restarting several times before finally wiping itself and having to do the whole set up process again. I formatted the card and set the card to active like instructed. But which rar do I need? I am running the nook hd with 2.1.0. Software. I tried all the nook hd bootfiles rars listed and added the zip I wanted to install and it keeps rebooting and wiping.
Thanks
Click to expand...
Click to collapse
You need the one that says NookHD, CWM and BOOTFILES and ends in rar. You must extract the 5 files there to the SD. Be sure to copy the one named MLO first.
Sent from my BN NookHD+ using XDA Premium 4 mobile app
leapinlar said:
You need the one that says NookHD, CWM and BOOTFILES and ends in rar. You must extract the 5 files there to the SD. Be sure to copy the one named MLO first.
Sent from my BN NookHD+ using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Ok thanks. I think I tired that one. But I will give it another go.