Database Users

U8800 Pro Upgrade

Hello everybody,
I bought today a U8800 Pro.It has Froyo installed and i'm trying to install official GB before upgrading to ICS.I' m following the official procedure with the pink screen and the file i'm using is the HUAWEI_U8800P_Android_2.3_V100R001C00B521.The procedure starts normally with unpacking but later i get the error message that Upgrade failed.
What am i doing wrong?

There was step1, step2 and step3? I think no... you must find the official gb version with all steps and flash it how is written in instructions.
Eclair and gb has different file systems and step1 is changing them. Step1 from ics is enlarging system partition, the file system of gb and ics is the same. If you buy this phone already, have a good luck with it
P.S. this is Q/A section?
Sent from my ragelis

Thanks bronxitas.
I'll start searching.

Placed Update.app in the dload folder in SD Card
Vol + + Vol - + Power.
Restart the phone.
Plz note that you have 512Mb available in SD card.

It's very hard to find the files.
I downloaded some files from here: http://forum.xda-developers.com/showthread.php?t=1366420&page=2
I completed step1 but now i cannot enter upgrade mode.
When holding Vol+ + Vol- and Power On i only get the pink screen.No upgrade mode.
Heeeeeelp!!!!!

giorgoslouk said:
It's very hard to find the files.
I downloaded some files from here: http://forum.xda-developers.com/showthread.php?t=1366420&page=2
I completed step1 but now i cannot enter upgrade mode.
When holding Vol+ + Vol- and Power On i only get the pink screen.No upgrade mode.
Heeeeeelp!!!!!
Click to expand...
Click to collapse
Try ones with official update with out battery using data cable or charger
Sent from my U8800Pro using xda app-developers app

giorgoslouk said:
It's very hard to find the files.
I downloaded some files from here: http://forum.xda-developers.com/showthread.php?t=1366420&page=2
I completed step1 but now i cannot enter upgrade mode.
When holding Vol+ + Vol- and Power On i only get the pink screen.No upgrade mode.
Heeeeeelp!!!!!
Click to expand...
Click to collapse
I wrote that you mus do exactly what is written in flashing instructions and what have you done? 2.2 -> 2.3 must be flashed with step1 and step2 renamed file. Both at the same time in the dload directory. Why you don't read the instructions??? An we must read you're crying?
If you finished with step1, you now must have different file system and theoreticaly you must flash only step2 and maybe step3. But i don't know if you will pass it ok. Becouse everybody can read and they done upgrade from 2.2 to 2.3 with 2 files in dload at the same time.
Have a good time by creating you're own methods of doing something, that can brick you're phone!
Sent from my ragelis

Hi,
I tried to upgrade u8800pro from Froyo 2.2.2 to Gingerbread, but I didn't successeded.
Here are the steps I've made:
1. I downloaded HUAWEI Ideos firmware(U8800Pro,Android 2.3,V100R001C00B521,Oversea Normal) from download-c. huawei. com/download/downloadCenter?downloadId=13574&version=14620&siteCode=worldwide
2. I erased all data from SD card.
3. I copied downloaded dload folder containing UPDATE.APP to SDcard.
4. In Settings->Privacy->Factory data reset I erased all data from phone. During this process, phone was restarted and set to initial factory state.
5. I turned off the phone.
6. I held Vol + + Vol - + Power.
7. On phone was displayed "Firmware update step 1/2 Unpacking"
8. "Update failed" appeared on next window.
Can someone advice me, what did I wrong? These steps are include more as is needed according Upgrade Guideline, but anyway it doesn't work.
Than You.

[fix] Huawei Honor 4x (CHE-L04) stucked at Honor logo { RECOVERY FIX FOR HONOR 4X }

Recently there was an issue with Honor 4x users who updated from KitKat (emui 3.0) --> Lollipop (emui 3.1) version due to some server issues(might be too many downloads at same time because of many many users of Honor4X in India) This is actually due to a corrupted recovery and flashing a new recovery might solve the issue.
To solve the issue HONOR 4X stucked at Honor logo ,i have an easy solution for all those users: Please download and extract the software package from below official path(around 35MB file)
https://drive.google.com/folder/d/0ByJkSOohdNz_Wnd6cVQ3Nlh1am8/edit
Requirements:
1) Make sure that the Micro SD card is available with enough free space(atleast 200MB) and can be read and write. It is recommended that The Micro SD card is made by Sandisk, Kingstone, or Kingmax.
2) Make sure that the power of the battery is enough to run the process. It is recommended that the power of the battery is more than 50%.
Procedure:
Step 1. Format the Micro SD card (This operation is OPTIONAL ).
Step 2. Copy the entire dload folder (with UPDATE.APP in it) contained in the file we downloaded to the root directory of the Micro SD card.
Step 3. Shut down the phone.
Step 4. Press the VOLUME UP + VOLUME DOWN + POWER Key(simultaneously for few seconds) to power on the phone and enter the Software Upgrade Mode begins automatically. This will start the FIX process on your device.
Step 5. When the progress bar stops(100% upgrade successful), the phone will automatically power OFF and restart.
:fingers-crossed::good: Your device should be working fine now. :good::fingers-crossed:

software upgrade mode not working
my software upgrade mode does not working, it always goes straight to the TWRP recovery mode

Ruisu23 said:
my software upgrade mode does not working, it always goes straight to the TWRP recovery mode
Click to expand...
Click to collapse
Upgrade needs stock recovery to be installed and I don't think tha TWRP is stock

booted to twrp instead of the stock emergency recovery? try using huawei update extractor and get all the .img files and fastboot flash all the .img files. the method is pretty much the same as fixing my own Che2-L11. once you flashed all the .img files, yes. it will not boot. but, you can access the emergency recovery menu (the menu that allows you to scan and would allow reparing via wifi). IF you can get to this menu, then youre ok good to go for forced upgrade via microsd. just make sure you are using the latest version available your your region. IF it didnt work, you have to fallback by fastboot flash the kitkat version of update.app and force upgrade with that kitkat update.app file. then when its fully booted to language screen, proceed normally as you would a hard reset all phone, then use the usual lolipop, next mellow official update.app file. then, your typical twrp, magisk, and more.

honor_ninja95 said:
Recently there was an issue with Honor 4x users who updated from KitKat (emui 3.0) --> Lollipop (emui 3.1) version due to some server issues(might be too many downloads at same time because of many many users of Honor4X in India) This is actually due to a corrupted recovery and flashing a new recovery might solve the issue.
To solve the issue HONOR 4X stucked at Honor logo ,i have an easy solution for all those users: Please download and extract the software package from below official path(around 35MB file)
https://drive.google.com/folder/d/0ByJkSOohdNz_Wnd6cVQ3Nlh1am8/edit
Requirements:
1) Make sure that the Micro SD card is available with enough free space(atleast 200MB) and can be read and write. It is recommended that The Micro SD card is made by Sandisk, Kingstone, or Kingmax.
2) Make sure that the power of the battery is enough to run the process. It is recommended that the power of the battery is more than 50%.
Procedure:
Step 1. Format the Micro SD card (This operation is OPTIONAL ).
Step 2. Copy the entire dload folder (with UPDATE.APP in it) contained in the file we downloaded to the root directory of the Micro SD card.
Step 3. Shut down the phone.
Step 4. Press the VOLUME UP + VOLUME DOWN + POWER Key(simultaneously for few seconds) to power on the phone and enter the Software Upgrade Mode begins automatically. This will start the FIX process on your device.
Step 5. When the progress bar stops(100% upgrade successful), the phone will automatically power OFF and restart.
:fingers-crossed::good: Your device should be working fine now. :good::fingers-crossed:
Click to expand...
Click to collapse
plz resend link

Soft brick CAN-L11 / Really need help

Hi everybody, i soft bricked my lovely Nova, here is the situatiuon :
- I tried to update the phone with the Emui 5 OTA zip but the phone turned off and now won't boot anymore
- When i try to boot normaly, it show the Huawei eRecovery and fail to recover the phone
- I can boot on fastboot mode / rescue mode
- I have TWRP installed and can boot on it but when i try to flash the can-L11c432.zip supplied by MORPH, it says "Failed to mount '/cust'" and stops here.
I really don't know what to do, moreover i lost the backup i made with TWRP.
If someone can help me i'll offer him a meal (paypal)
Sorry for my bad english and have a nice day everyone.

Hi Keezle,
here is the recovery.img from the EMUI5 Beta Update. Flash it with fastboot and apply the update once again (Boot with Power + Vol down + Vol up) After the Update is complete make a full wipe in the stock recovery.
You need a external SD Card with the dload folder thats include the Update.

Keezle said:
Hi everybody, i soft bricked my lovely Nova, here is the situatiuon :
- I tried to update the phone with the Emui 5 OTA zip but the phone turned off and now won't boot anymore
- When i try to boot normaly, it show the Huawei eRecovery and fail to recover the phone
- I can boot on fastboot mode / rescue mode
- I have TWRP installed and can boot on it but when i try to flash the can-L11c432.zip supplied by MORPH, it says "Failed to mount '/cust'" and stops here.
I really don't know what to do, moreover i lost the backup i made with TWRP.
If someone can help me i'll offer him a meal (paypal)
Sorry for my bad english and have a nice day everyone.
Click to expand...
Click to collapse
I came to a similar situation. The CUST supplied by Morph seems not to be flashable. Untick the CUST when flashing the NANDROID. It will go through the process and the phone will eventually boot again.

-=MoRpH=- said:
Hi Keezle,
here is the recovery.img from the EMUI5 Beta Update[/URL]. Flash it with fastboot and apply the update once again (Boot with Power + Vol down + Vol up) After the Update is complete make a full wipe in the stock recovery.
You need a external SD Card with the dload folder thats include the Update.
Click to expand...
Click to collapse
Si, i put the C432B320 update.zip in dload folder on an external SD Card, i flashed the Emui 5 beta update recovery successfully, but when i boot with Power + Vol down + Vol up it starts the installation and stops at 5% saying "Software install failed !". Should i use another update.zip file ?
Thank you MORPH

Keezle said:
Si, i put the C432B320 update.zip in dload folder on an external SD Card, i flashed the Emui 5 beta update recovery successfully, but when i boot with Power + Vol down + Vol up it starts the installation and stops at 5% saying "Software install failed !". Should i use another update.zip file ?
Thank you MORPH
Click to expand...
Click to collapse
Maybe unpack the C432B320 until you have an update.app in dload folder. I did that and flashed the ROM. The first try was a failure and I had to restore a NANDROID (bootloop). Currently, I'm trying to flash it again but now with the EMUI5 recovery morph has supplied.

System of a pWne!^ said:
Maybe unpack the C432B320 until you have an update.app in dload folder. I did that and flashed the ROM. The first try was a failure and I had to restore a NANDROID (bootloop). Currently, I'm trying to flash it again but now with the EMUI5 recovery morph has supplied.
Click to expand...
Click to collapse
I'll try this now thank you

Keezle said:
I'll try this now thank you
Click to expand...
Click to collapse
But be careful and have a backup. I just flashed it and it seems not to work again :/ It just keeps on sitting on the Huawei logo for minutes now. That's it.

System of a pWne!^ said:
But be careful and have a backup. I just flashed it and it seems not to work again :/ It just keeps on sitting on the Huawei logo for minutes now. That's it.
Click to expand...
Click to collapse
So now, it start installing update and says "installation failed !" at 50%

Keezle said:
So now, it start installing update and says "installation failed !" at 50%
Click to expand...
Click to collapse
What OTA do you currently try to flash? I currently try to give my luck to CAN-L11C432B320 even though I have a L01 device. http://update.hicloud.com:8180/TDS/data/files/p3/s15/G79/g0/v71311/f1/full/update.zip

If needed, i updated the link for the cust img...
http://forum.xda-developers.com/showthread.php?p=70294269

Same isseu with other update files, i think i have to wait for the full EMUI 5 firmware..

Keezle said:
Same isseu with other update files, i think i have to wait for the full EMUI 5 firmware..
Click to expand...
Click to collapse
hello I have the problem Software install failed! can you help me thanks in advance

better work with ADB and flash 3 main imgs....recovery,boot,system images...then reboot...then do the 3 buttons update

need help
Hello dear friends
Do not be tired
I need a dump file Huawei Can l11
The ears are burned and their hard drive is changed
If there is someone else's phone root, please give me a dummy file
thanks to everyone

Downgrade to Marshmallow

Hello Friends, I just upgraded my Zenfone 3 ze520kl to Nougat, but i prefer Marshmallow i try from recovery mode to flash Marshmallow, it shows error and the installation aborted. Can any one help . Thanks.

What error does it show?

Error with some numbers follows by 'install aborted'. I unable remember the error numbers. I did three times all the time with same remark.Thanks.

That's not very helpful. Can you try it again and tell us exactly what it says?

Hi,
I downgraded a few days ago, here's an overview of the steps.
WARNING, this requires a factory reset so you will lose the data on the phone, so make sure you have backups before you proceed. You do this at your own risk and I am not responsible for any damages.
I assume you have adb / drivers all configured and know to how use them.
1) download firmware file http://dlcdnet.asus.com/pub/ASUS/ZenFone/ZE520KL/UL-ASUS_Z017D_1-WW-13.20.10.152-user.zip and save to SD card / insert card in phone.
2) download recovery and boot img files for Z017D_WW_13.20.10.152
- https://mega.nz/#F!ok0V0RIA!5WKtHe98opzjVI3NPbM7Ww
- under the folder Z017D_WW_13.20.10.152
3) Go to fastboot mode (power + vol up)
- flash recovery.img (command: fastboot flash recovery recovery.img)
- flash boot.img (command: fastboot flash boot boot.img)
4) reboot to recovery (power + vol down)
5) install update form micro sd card.
set the file UL-ASUS_Z017D_1-WW-13.20.10.152-user.zip that you saved earlier
6) wipe cache
7) factory reset
If you don't do a factory reset and reboot, Android pretty much crashes on multiple processes on start up, it is unusable.
Regards,
TK

Credit goes to https://forum.xda-developers.com/zenfone-3/help/guide-how-to-root-zenfone-3-ze552kl-t3471524 for laying the foundation.

Warning- No file-contexts. This package is for "ww-phone" devices, this is a E:error in /side load/ package.zip (status 7) Installation aborted.

Same thing happened to me as well. I just went ahead to flash the RAW file (http://www.asus-zenfone.com/2016/12/asus-zenfone-3-raw-firmware-and-asus.html) and updated the software to the latest marshmallow update, followed by a factory reset.

If we Downgrade
Then we get update in future yes or no??
Sorry for bad English??

Yes.

Hi, thanks for the help. Please answer this:
Do I need to use Recovery and Boot.img the same version of ROM? Why?
Why do I need to install Boot.img?

samsung s4 mini GT-I9195 LTE dead phone

hello guys
i need help about flashing my 2 dead phone GT-I9195.
in my laptop it shown : Qualcomm HS-USB QDLoader 9008 .
i know we can't use qpst so sad .
i'm searching for solution without the z3x box or any other items.
First i follow this guide :
LINK (
[HARD BRICK ?] - I919x - Make your debrick.img and have it on extSdCard by security
Hi People We all must have the debrick.img on our extSdCard by security. If we have a Hard Brick we can make like this examples solved whit success. See two HARD BRICK's solved. I have sending them the debrick.img: This whit a Guide...
forum.xda-developers.com
)
debrick.img 4.4.2 -> LINK (https://mega.nz/#!T9hxAJQC!e74HQeHhU66fmPFVFOLdxTtFyR-fxntfc37qFb22oRA)
i use Win32DiskImager to flash the debrick.img in 16GB Sd card
i put sd card in the phone.
the phone boot to T-flash(Odin) .
i use the CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit and then i flash I9195XXUCQL2_I9195XXUCQL2.tar from TRWP guide : LINK (
[RECOVERY][OFFICIAL] TWRP 3.5.2_9-0 [I9190][I9192][I9195][L520]
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and...
forum.xda-developers.com
)
i tried TRWP , CWM recovery.img and both worked.
in TRWP only focused on the internal Storage and it is 0 MB , can not wipe or mount or do anythink , i want to change TRWP to see the SD CARD.
so with CWM i can use adb sideload to falsh zip file.
i try cm-13.0-20161219-NIGHTLY-serranoltexx.zip with adb : not work ,no system shown.
when i change the phone to download mode i flashed :
I9195XXUCQL2_I9195TMZCQL2_I9195XXUCQL2_HOME.tar ,
I9195XXUCPB1_I9195ITVCPB2_I9195XXUCPB1_HOME.tar ,
I9195XXUCNH5_I9195OJVCNH1_I9195XXUCNH5_HOME.tar.md5 ,
I9195UBUCOH1_I9195ZVVCNI1_I9195UBUCOH1_HOME.tar.md5.
no system shown , and the phone back to the T-flash and i do the same reflash CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit and I9195XXUCQL2_I9195XXUCQL2.tar to can boot to download mode.
The big problem is there is no system. only i can use download mode and recovery mode(TRWP , CWM).
I want the phone to have system
please anyone can help me , i'll do my best in research.

chakroun saifallah said:
hello guys
i need help about flashing my 2 dead phone GT-I9195.
in my laptop it shown : Qualcomm HS-USB QDLoader 9008 .
i know we can't use qpst so sad .
i'm searching for solution without the z3x box or any other items.
First i follow this guide :
LINK (
[HARD BRICK ?] - I919x - Make your debrick.img and have it on extSdCard by security
Hi People We all must have the debrick.img on our extSdCard by security. If we have a Hard Brick we can make like this examples solved whit success. See two HARD BRICK's solved. I have sending them the debrick.img: This whit a Guide...
forum.xda-developers.com
)
debrick.img 4.4.2 -> LINK (https://mega.nz/#!T9hxAJQC!e74HQeHhU66fmPFVFOLdxTtFyR-fxntfc37qFb22oRA)
i use Win32DiskImager to flash the debrick.img in 16GB Sd card
i put sd card in the phone.
the phone boot to T-flash(Odin) .
i use the CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit and then i flash I9195XXUCQL2_I9195XXUCQL2.tar from TRWP guide : LINK (
[RECOVERY][OFFICIAL] TWRP 3.5.2_9-0 [I9190][I9192][I9195][L520]
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and...
forum.xda-developers.com
)
i tried TRWP , CWM recovery.img and both worked.
in TRWP only focused on the internal Storage and it is 0 MB , can not wipe or mount or do anythink , i want to change TRWP to see the SD CARD.
so with CWM i can use adb sideload to falsh zip file.
i try cm-13.0-20161219-NIGHTLY-serranoltexx.zip with adb : not work ,no system shown.
when i change the phone to download mode i flashed :
I9195XXUCQL2_I9195TMZCQL2_I9195XXUCQL2_HOME.tar ,
I9195XXUCPB1_I9195ITVCPB2_I9195XXUCPB1_HOME.tar ,
I9195XXUCNH5_I9195OJVCNH1_I9195XXUCNH5_HOME.tar.md5 ,
I9195UBUCOH1_I9195ZVVCNI1_I9195UBUCOH1_HOME.tar.md5.
no system shown , and the phone back to the T-flash and i do the same reflash CSB_signed_SERRANOLTE_ONEPIT_OPEN_130523.pit and I9195XXUCQL2_I9195XXUCQL2.tar to can boot to download mode.
The big problem is there is no system. only i can use download mode and recovery mode(TRWP , CWM).
I want the phone to have system
please anyone can help me , i'll do my best in research.
Click to expand...
Click to collapse
Hello , i think you wiped your system you have to install another one. Try Lineage Os

If it does not work try shutting down the phone, remove battery and hold power button for 30 seconds.

Zac C4rter said:
If it does not work try shutting down the phone, remove battery and hold power button for 30 seconds.
Click to expand...
Click to collapse
remember i can't control the internal storage because the phone is dead , i only have the files and partitions in the SD card(external Storage) .
i already tried Lineage Os . the CWM say
+ can't mount /cache/system , mount : failed .... and long message.
it show erreur then installation aborted.
all this because the partition is in /storage/sdcard1.
so how i should redirect the installation ?

chakroun saifallah said:
remember i can't control the internal storage because the phone is dead , i only have the files and partitions in the SD card(external Storage) .
i already tried Lineage Os . the CWM say
+ can't mount /cache/system , mount : failed .... and long message.
it show erreur then installation aborted.
all this because the partition is in /storage/sdcard1.
so how i should redirect the installation ?
Click to expand...
Click to collapse
Try switching to Ext4
:Edit
Also Check Here https://appuals.com/how-to-fix-twrp-unable-to-mount-storage-internal-storage-0mb/

Zac C4rter said:
Try switching to Ext4
:Edit
Also Check Here https://appuals.com/how-to-fix-twrp-unable-to-mount-storage-internal-storage-0mb/
Click to expand...
Click to collapse
i have tried it all the 11 steps and not work. internal storage is 0 MB
i'm using trwp 3.5.0_9.0
after i flashed the SD card with Win32DiskImager and with the debrick.img , everythink now is in the external storage, my problem is i can't access to it, or install zip file with trwp or cmw because i can't mount the partitions in trwp or cwm.
i only can use download mode to flash files by odin
i want to know if i can do it manuelly by termianl commends in trwp .
but how i can know the places of the unmounted partitions ?