[Q]Hardware Trouble, any reliable source for parts? - HD2 General

I've had my HD2 for a few months now, problem is, mine was already quite beaten when bought. Wi-fi antenna wire thingy was busted, stole one from a dead Desire A8181, touchscreen was mis-glued due to a badly replaced display, lenses for proximity and light sensor are missing, screen has a whole line of dead pixels, case is busted, and so on.
Last week it started hanging up randomly on android. Thermal trouble. Fixed. However, when tearing the damn thing apart, I ripped the already messed flex cable. Great, now I can't flash, use MAGLDR, recovery, etc. Can anyone point me a reliable part/phone source? I'm in Brazil, so most eBay sellers are a no-go. Or, if anyone has a dead/beaten TMo Leo they are wishing to sell/trade, PM me. Dunno if I'm posting this right, but as I'm a XDA noob, no marketplace for me.
Sent from my LG-P768 prototype

Let me know what you need, maybe I can help you!

Related

G1 ribbon/tape caught in its Hinge

Yesterday, I impulsively rooted my phone (my first time), successfully did it after several tries and installed jf 1.5. When everything was done and fully functional, I noticed some resistance when closing the keyboard. I tried closing it several times trying to investigate the cause.. until my screen just went black suddenly, w/ the resistance in closing it getting stronger! What I discovered was that the brown tape inside the screen, bottom part, ( the one you can only see w/ keyboard open) was caught in the hinge ripping it partially out of place. I dont have any idea what is the main finction of that tape/ ribbon but I believe it has something to do w/ the lcd. I ended up w/ a dead phone, won't power up anymore. i called the customer service but they don't have any idea what i'm talking about and suggested me to go to the nearest Tmobile store. I did and to my disappointment, nobody in the store also knows anything about G1, even though I'm pointing out to them the tape that was caught by the hinge! I called customer service and they seem not to understand about that hinge part of G1. Anyway, they will send a replacement in 3 days and I hope they wont discover that I rooted the phone. Well, it won't power up anymore and besides the problem is on the hardware and not on the software I installed.
I came across the same problem posted in one of the forums,a long time ago, coupled w/ some pictures I tried searching it again to no avail.
Anybody here have the same problem w/ G1? I do believe that HTC and Tmobile should be aware of this hardware flaw and do something about it. I love my G1, w/ its physical keyboard. But if all my G1 will end up this way, I may have to find a better phone.
Yep... had the same thing happen to me. Brought it into the store (30 days or less) and got a new one. If your's is older, it should still be under warranty. Contact T-Mobile and they should send you out a new phone.
That ribbon has several conductive traces in it. Basically, its a bunch of wires, and you moosed it out. I would say that it was your fault for forcing it when you should have investigated the problem BEFORE ripping it out.
Sounds like your screen just doesnt turn on, not that its bricked.
Thats the ribbon that connects the lcd and backlight to the ui module. It can be fixed most likely if you're not afraid to take it apart. What prob happened is the ribbon got bent up a bit, and one of the 2 connections for it got pulled out.
I disassembled one of my G1's completely, and there is a very specific way that ribbon has to fit into the hinge. Its not all that difficult, but you have to be very gentle and patient to get it back to where it needs to be.
You should go to the Dev forum, and do a search for G1 repair manual. You'll see what i mean. Feel free to PM me if you have any questions about it, although Im not an expert, just a tinkerer.
@lbcoder: you dont have to "investigate" anything, its made the way it should work, all he did is open and close screen, thats called a manufacturer defect, and falls under warranty.
@tr.slate: you are right, however that's exactly what OP put in his post. Nothing bout phone being bricked, but hardware flaw.
@jdc2006: yes, G1`s construction is not the most durable, as we can read around this forum, even i had squeking (or however oyu spell that word) but im guessing that it`s the price we pay for something new as this (though i would expect a bit more from HTC) but i dont think that all will have that problem. though Im on my second G1, first one got nasty case of stuck pixelitis.
now excuse me, i have to dispose a body from the trap.
G`nite.
This is going to be my 4th G1 and I hope the last..
The 1st one- brand new; has dead pixels- returned/replaced
The 2nd one, obviously a refurbished item, keyboard imperfectly fitted; home/call buttons replaced w/ cheap looking plastic, not the marble-like.
This 3rd one- almost perfect but ribbon/hinge flaw.
Good thing is I still have my old HTC Touch
tr.slate.. tnx, I like to tinker too but this beyond my capabilities.
I never had any problems with Tmobile fixing mine...When I first got mine in February 09 the ribbon stuck out a bit....they told me come back in 2 hours, i came back and they had it fixed, as others have said, it really needs to be in the right spot or something bad could happen to it...Its a cell phone, not much space to use.

Weird problems. Whats your opinion?

Thought I'd share my story. I recently got a swap out for a "dusty" screen. My new phone seemed OK. A few days passed by and my camera flash started acting up and not working... Today I woke up and NOTHING on the top half of my phone works. Meaning my ear peice, my 3.5mm jack, my camera, or flash, or proximity/light sensors... nothing. But the speakerphone works, my screen is fine. and my microphone works. kinda odd!
It almost like the top PC board got disconnected internally or something.
Just thought this was a strange issue. Already requested yet ANOTHER swap from HTC. Hopefully this next one can make me beleive this phone was worth it.
On another note. I did get my phone "ghost armored" at a cart in the mall pretty much immediately upon receiving it from fedex. And they do spray a small amount of soapy liquid on the outside of the phone to apply the skins. Do you think this could be enough to cause water damage? I'm afraid HTC is going to charge me for "non warranty problems" if the guys at ghost armor caused this! Its a very "fine mist" they use so I think it would be hard to penetrate the phones seals. But who knows? Whats your opinion?
dills84 said:
Thought I'd share my story. I recently got a swap out for a "dusty" screen. My new phone seemed OK. A few days passed by and my camera flash started acting up and not working... Today I woke up and NOTHING on the top half of my phone works. Meaning my ear peice, my 3.5mm jack, my camera, or flash, or proximity/light sensors... nothing. But the speakerphone works, my screen is fine. and my microphone works. kinda odd!
It almost like the top PC board got disconnected internally or something.
Just thought this was a strange issue. Already requested yet ANOTHER swap from HTC. Hopefully this next one can make me beleive this phone was worth it.
On another note. I did get my phone "ghost armored" at a cart in the mall pretty much immediately upon receiving it from fedex. And they do spray a small amount of soapy liquid on the outside of the phone to apply the skins. Do you think this could be enough to cause water damage? I'm afraid HTC is going to charge me for "non warranty problems" if the guys at ghost armor caused this! Its a very "fine mist" they use so I think it would be hard to penetrate the phones seals. But who knows? Whats your opinion?
Click to expand...
Click to collapse
water can literally penetrate the smallest most microscopic points. but i dont know think "mist" could do any harm. i think it sucks that you're having bad luck with all these though man.
I like straweberries, they taste good. When eaten slightly chilled they are refreshing as well. And the things you can do with them... fresh fruit topping for cereal, pancakes, yogurt, or you can make them into jam/jelly/compo(sp?)
Anyways, yes, it is possible for your device to have received water damage, this is why I have not and will never put something on my phone that requires the use of water in the application process. And it might even be probable given that on the top of the phone you have a 3.5mm jack, speaker housing, and when you take the back off this gets exposed... and I am guessing they removed the back before misting it, so even more water can get into that area causing major issues.
pjcforpres said:
I like straweberries, they taste good. When eaten slightly chilled they are refreshing as well. And the things you can do with them... fresh fruit topping for cereal, pancakes, yogurt, or you can make them into jam/jelly/compo(sp?)
Anyways, yes, it is possible for your device to have received water damage, this is why I have not and will never put something on my phone that requires the use of water in the application process. And it might even be probable given that on the top of the phone you have a 3.5mm jack, speaker housing, and when you take the back off this gets exposed... and I am guessing they removed the back before misting it, so even more water can get into that area causing major issues.
Click to expand...
Click to collapse
Haha, thanks for your opinion on strawberrys.
I believe they remove the battery, but put the battery cover back on before misting. They also leave the device off while they do this and tell you to leave it off for an additional 2 hours (i left mine off for 6 or 7 hours.)
Even leaving it off, if water gets it, it gets in, and starts causing the circuits and what not to corrode.
I will say, I think it is highly unlikely that you do have water damage causing this problem. If HTC says no go, water damage, those misty dudes are responsible and liable to replace your device/pay for repairs. But, I do highly doubt it.
Still, there is a chance of there being water damage, and even if it isn't causing the problem, HTC won't care.
All in all, I would put money that the swap goes just fine, and hopefull 3rd time is the charm for you. It seems some people, no offense, just have really bad luck with these, while others (not to brag), have bought 5 of them without a single problem.
pjcforpres said:
Even leaving it off, if water gets it, it gets in, and starts causing the circuits and what not to corrode.
I will say, I think it is highly unlikely that you do have water damage causing this problem. If HTC says no go, water damage, those misty dudes are responsible and liable to replace your device/pay for repairs. But, I do highly doubt it.
Still, there is a chance of there being water damage, and even if it isn't causing the problem, HTC won't care.
All in all, I would put money that the swap goes just fine, and hopefull 3rd time is the charm for you. It seems some people, no offense, just have really bad luck with these, while others (not to brag), have bought 5 of them without a single problem.
Click to expand...
Click to collapse
5 of them?! jeez!
I agree, I'm having really bad luck. I LOVE this phone. Its just getting annoying having to swap it out every other week.
I'm also angry that this broken one has the best screen I've seen on any nexus, no dust, no pink tint. its perfect! and i have to return it
Oh well. thanks for the advice. I feel a little better about the swap now, I cant really afford to lose another 530$.
One for me, and 4 others for friends that had me help them buy one...

Replace lcd screen or motherboard?? Maybe? Maybe not??

Ok this one goes out to all you cool smart guys out there. I currently have two mt4g's. One is working perfectly fine with the "bad screen", as they call it, and the other is bricked, or no it has a failed pu is what someone told me, but it has the "good screen".
Anyway while just minding my own business on the internet one day I came across a video which shows you how to replace a lcd screen in a mytouch 4G! I was hooked. I could do this I said, it looked so easy! Sure you need some patience, which I got btw. So I was determined to do this, even ordered the tools from repairsuniverse. So about the fourth time watching the tutorial I began to wonder if it would be possible to just swap motherboards instead of disassembling all the way to the screen. Mostly because I still need a heat gun so i could remove the digitized then lcd screen.
So i guess my question is will swapping motherboards solve the pu problem in the mytouch with the good screen? And while I got you here has anyone ever replaced there lcd screen?? Is it worth it??
Sent from my HTC Glacier using XDA Premium App
Yes, if you put the good motherboard in the case with good LCD, you'll get one good phone.
Thanks for the response! This will make the job so much easier
repair options
sorry to piggyback you post but i had a similar question....
a friend of mine is giving me their broken mytouch 4g. it was working perfect but then she dropped it on her kitchen tile (bottom right corner hit i'm told) and now it will not turn on at all.....no cracks or anything, just a scratch in the corner. she says she tried a new battery and tried plugging into AC but no lights, nothing.
i've taken apart enough phones so once I get it i'm not afraid to do some swapping of parts.
my question is, those of you who have worked on this model, any indication where you think would be the problem? i'm hoping the lcd/digitizer is fine since its not cracked but we'll see....and i figured maybe i would just need to do a motherboard swap worst case? is there any other components you think could be shot after the drop? from what i've been able to find its just the 1 main mother board , correct? (meaning there is not 2 parts)
thought MAYBE i'll get lucky after opening it up, and verifying all the cables that possible some cables got jarred loose and thats why it wont respond but not holding my breathe on that.
thanks for the help!

unresponsive touch screen

So my girlfriend drooped my phone and broke it on me. Oh my beloved atrix what ever will I do without you. Everything about the phone is working just fine so I am curious if its just the touch panel that ia broken. I touch the screen and nothing happens I have fully charged it and turned it on and off several times. Do you guys think if I replace the touch panel that there is a chance it will work again. I didn't get insurance on it because I was very careful with it and took care of it like it was my child lol.
First of all I would like to point out that it is ok to admit that you dropped it, and not your gf.
Secondly I would suggest tearing it down and checking the connections. I have seen where the digitizer connector will be loose and wont be responsive on other phones. I have never taken apart the atrix, so I dont know if that is a unlikely thing for it or not.
In the unlikely event that it really was your gf who dropped it, you could always guilt her in to getting you a new phone
Lol I swear it was her we were at the bar last night and she was trying to show somone the gi Joe psa's. Ill try and tear it down have to find a walk through I guess. The real kick in the teeth is I just bought a e book and it was really starting to get good . As far as guilting her, her parent were with us and gave me a kindle fire because they felt bad but the things useless until they get android running well enough on it.
there is a teardown site, i am too lazy to look it up, I am supposed to be studying business law right now ... dont tell my wife im on xda
I tried to replace my digitizer once and I wouldn't recommend trying to fix it yourself.
There are several youtube videos of the teardown and they are elaborate enough but some parts are really tricky and it's not as easy as it might look. Took me a few hours and the result was far from perfect...
Took the mobo out and checked all plugs everything seems fine. Replaced and still no response I will give the digitizer a try hopefully it works. Ordering it tonight and post my results when it comes in and i install it. I'm supprised you had problems putting it back together only problem i had was my God damn shaky hands lol. I am assuming it fell just right and damaged the chip on the digitizer itself. If it ends up working I know for sure that I will be buying a very buff case! The internals on these things are so fragile!

MyTouch 3G slide screen not working

Hey guys, I have had this phone since August of 2010 and personally its really nostalgic, in all reality I prefer it over my Galaxy S, Especially for the Slideout keyboard and seems to have better ROM support :/ But around November 2011 the screen would spaz out not respond and just not turn on. Sometimes it would but so dark it was nearly impossible to see it. I'm not sure if the screen is dead I haven't used it since November when I got my Galaxy S. If the screen is dead, is there any type of repair service? or a way to buy a top half for the screen and replace it?
Look on Ebay, there are lots of these phones for cheap.
Sent from my T-Mobile myTouch 3G Slide using xda premium
Sounds like a loose connection on the cable for the screen. I had the same problem with mine. I'm still using this phone now. Free fix if you can figure out how to take the phone apart & basically unplug & re-plug. Be super careful though! And of course it could be a different problem.
You can buy a new one very cheap in amazon or ebay i dont think it worth to repair
Not sure it's the right place to post this, I replaced the digitizer in my old MT3GS (cracked in my pocket), and ever since, Ive have the screen-spazzing issue as well - wasn't my first time replacing a screen, either. For me, the solution _every time_ has been hit the power button to lock the screen, hit it again to get back to what I was doing... Never had to totally power down to fix the spaz :\
If it'd interest you at all, I'd be willing to send you the phone, charger brick, (and the metal case if I can find the damn thing) for $50+ship - thats what I paid for the new digitizer... If you have better troubleshooting skills than I do, good on you, because I've torn this one down and put back together again at least 2 or 3 times since replacing the digitizer, and can't find a single loose connection - maybe you'll have better luck than me?
Thanks
L4T
I called a repair shop I found on craigslist and they mentioned it's more than likely the flex cable, not the lcd screen or glass digitizer. These phones' cables go through lots of wear due to the sliding mechanism. They gave me a 70 dollar estimate, so I just don't slide my phone out anymore to prevent the screen from spazzing out or blacking out for good (it happened to a friend of mine's MTS3g). I've also seen the cable for sale online on ebay or repairsuniverse but I'd rather wait for my full upgrade than invest in it AND risk not fixing it.
I really wanna use this phone again, the slide mechanism is so worn on it you can feel it its kinda tough to do its not springy like it was outta the box, also on ebay these phones still run close to 200 dollars, I would take it apart, as its out of warranty anyways, but I don't have the proper tools to do so, like the mini philips head and the tiny socket wrench. And I hear it is most likely the flex cable but as I said I can't access it.

Categories

Resources