Database Users

Broken touch screen, need to get Stock

The touchscreen on my Fire stopped working today. I already talked to Amazon and am getting a replacement, but I want to revert back to stock before sending it in. I've seen ways to do this with TWRP, but I don't have a touchscreen to use TWRP, or any recovery for that matter, with.
Is there any way to do this?
I do have full ADB and Fastboot access, with FireFireFire working, but do not have a currently working rom installed (I was on CM9, and it won't go past the boot screen).

drk.hd said:
The touchscreen on my Fire stopped working today. I already talked to Amazon and am getting a replacement, but I want to revert back to stock before sending it in. I've seen ways to do this with TWRP, but I don't have a touchscreen to use TWRP, or any recovery for that matter, with.
Is there any way to do this?
I do have full ADB and Fastboot access, with FireFireFire working, but do not have a currently working rom installed (I was on CM9, and it won't go past the boot screen).
Click to expand...
Click to collapse
There is a way to do this with adb... I just do not know the proper commands. Sorry

Does installing a custom rom void the warranty? Seems like it would be BS for Amazon not to honor it when it's apparently a hardware related issue.

sengwall said:
Does installing a custom rom void the warranty? Seems like it would be BS for Amazon not to honor it when it's apparently a hardware related issue.
Click to expand...
Click to collapse
No, I don't think it does, but I'd rather not take the chance.

drk.hd said:
No, I don't think it does, but I'd rather not take the chance.
Click to expand...
Click to collapse
YES! It absolutely does. The second the device was rooted it broke warranty.
Sent from my myTouch_4G_Slide using XDA App

The same thing actually happened to me earlier today. I was just browsing some sites on the ICS rom when it just stopped responding. I couldn't get it to recognize any touches even after a bunch of reboots, so I just figured it to be some bug that hadn't been squashed yet. When I dropped down to recovery and saw the same issue, I knew I had a real problem.
Hoping against hope, I tried both CWMR and TWRP on it and got no results. Like you, I figured it would have to go back to Amazon, so I started searching for a way to get it back to stock... nothing obvious jumped out at me because everything is written with access to recovery in mind... which doesn't help.
So, I started reading about adb and going through the built-in help. As I was familiarizing myself with some basic adb commands and options, I left TWRP open in front of me. I don't know how long I had it that way when I mindlessly tapped on the screen and thought I saw it flicker. Yes! I had pressed the Wipe button and it had taken me to that section. It's been working fine ever since.
I'm not claiming I did anything and I don't have a how-to on how to fix it, but it couldn't hurt to just leave the thing running in recovery for a while and see if the touchscreen comes back to life for you too.
Still, I'd love to see someone with more adb knowledge provide a simple tutorial on how to get it back to stock without access to recovery. I'm sure it would be helpful to someone in the future... maybe even me if the same problem comes up again.
Best of luck to you.

Just ignore my comment
Sent from my Amazon Kindle Fire using Tapatalk

If your on the rooted stock rom you could always wait until Amazon pushing the next OTA

You will have to make a fastboot image and flash that with fastboot. But before you create the image, you will have to create all the appropriate symlinks. Then you run...
Code:
make_ext4fs -l 512m -a system -s /path/to/fastboot_system.img /path/to/system_folder
That will create the fastboot image. Then when FFF gives you fastboot access, you run...
Code:
fastboot flash system fastboot_system.img
You will also need a fastboot image for recovery and the bootloader.

Isn't there any easy way like with my desire, simple ruu.
Or hasn't anyone created these images to flash. I also need to get back to stock everything and send it to amazon, my wifi gets error after some period of time and some times when screen goes off, try'd 3 roms and stock.

There is a way to tell the device to install /sdcard/update.zip via shell commands. I forget what they are tho. Something about the extendedcommands. If I have time tomorrow I'll look it up.

here it is:
http://www.theandroidsoul.com/kindle-fire-stock-rom-installation-guide/

b63 said:
here it is:
http://www.theandroidsoul.com/kindle-fire-stock-rom-installation-guide/
Click to expand...
Click to collapse
Thanks for the link. I'm back on this thread because I think my Kindle Fire touchscreen is now dead for good. However, those instructions do not work as-is because you need to press a button on the screen to tell the Kindle Fire to allow the host to mount it as a USB Mass Storage device. Although those instructions don't get you all the way there, I was able to use the core idea to get my Kindle Fire back to stock. So, many thanks for pointing me in the right direction.
On top of the touchscreen not working, I ended up partially bricking the device trying to find a way to flash it back to stock, so I had also posted in the Unbricking thread. I posted my solution there....
http://forum.xda-developers.com/showpost.php?p=23226260&postcount=701
Odds are, if you have a device that is booting correctly, you will be able to ignore steps 3 and 4 and get it booting back to stock. I do have a couple of other suggestions... Leave your USB cable hooked up to the Kindle Fire as it boots into stock for the first time. This is the only time that it will automatically mount the /sdcard to your computer and you will have a chance to reclaim (and delete) all the files stored there. You can also do something like 'adb pull /sdcard C:\sdcard' before you flash. Also, depending on what ROM and apps you were using before starting the process, you might want to delete your user data and reset the device to factory defaults. You can do this with 'fastboot erase userdata' and the next time you start the device, you'll get a warning that it's about to reset. Hit the power button and you should have a clean, fresh from the factory Kindle fire... albeit with a broken touchscreen. Good luck!

After several failed attempts to follow this guide (no offense to posters; I appreciate your contributions), I found this to be the simplest method.
http://stackoverflow.com/questions/10817721/wipe-data-factory-reset-through-adb
Download stock update, then it's basic procedure in adb:
adb push C:/update.zip /sdcard/update.zip
adb shell
recovery --wipe_data
After reboot, go back into to adb shell and do "recovery--update_package=/sdcard/update.zip"
Factory reset, etc. and you're good to go.

[Q] please help with my nexus....

I went to flash cyanogenmod 10.1.
backed up rom via clockwork.
wiped data, flashed new rom.
flashed gapps.
I think i flashed the wrong gapps
upon boot I get "setup wizard has stopped" as well as one regarding gapps.
this prevents me from using the rom. I can access the calender and clock that is all. not the settings or reboot menu.
I can access the built in storage via windows, shows up as a nexus 7.
Ok, not a big deal, I will boot into recovery via the bootloader.
That no longer works. Sits at a google screen forever
Ok, I will use fastboot via the bootloader....
That no longer works. As soon as a usb cable touches the nexus either power or pc it freezes the bootloader requires a reboot.
windows rejects the usb and states is malfunctioned and unrecognised (though it works fine in the rom)
fastboot doesn't see the device.
I've tried:
three usb cables.
windows safe mode.
different ports
uninstall/install drivers.
nexus tool kit (doesnt recognise device)
wiggling the cable as suggested
anybody got an idea how I can either get the bootloader not to freeze when using a usb cable or how to boot into some kind of recovery (which was there!!!!!)
please? :fingers-crossed:

Something seems a little off here.
Was it a gapps package for some other device? Hard to see why flashing something to /system would produce the result you got, as the (gapps) edify script would at most specify a mount of "system", not a /dev/block/ device name.
Does adb work (with the ROM booted)? If so, can you get a root shell or install .apks?
The fact that the ROM boots suggests that the bootloader is working correctly enough to load and execute the LNX (boot) image. That means that in principle you could flash (using the "dd" command) a recovery image to the boot partition from a root-privileged command line (either an adb session or a terminal emulator). Performing a regular (power button) restart would boot you into a recovery session.
Obviously, this hinges on you getting a command line somehow with your reduced-functionality ROM limping along as it is. It's not obvious to me how you will make that happen though.
I am not at all confident that this will fix the bootloader <--> USB issue without somehow reflashing the bootloader without using fastboot!. The only way this has been observed for the N7 has been with the OTA process and a stock recovery - the OTA puts an image (**note - important!** this OTA bootloader image is slightly different from the bootloader image in the factory/fastboot ROMs) into the USP partition and some magic occurs on the next boot.
Well, anyway there's some ideas. Would you mind identifying the "wrong" gapps that you used? For the life of me I can't see how it caused the symptoms you are observing...
good luck

Hi. Many thanks.
Ok.....
Gapps. I downloaded the appropriate package via the link on the Rom page. However, I flashed a jellybean package I'd downloaded for my one x. I may be naive in thinking that Gapps is Gapps no?
I deduced it was that having googled the setup wizard problem and seeing that others had had it.
Bootloader.
Again. Ive googled around and can see many have the freezing bootloader with usb issue. Some say its the cable. Some say its the pc. But it does it with the charger as well. Again this is an issue for some. not sure what to do! Works fine until the cable goes in.
Recovery.
Again I know its an issue booting recovery from bootloader. I've read you need the usb in to a pc to make it happen. Obviously that's a no go for me
Adb.
Never really used it. Used fastboot many times. I assumed you need to be able to access the developer options and activate debugging etc within the Rom to allow it to work? I can not do that. Its around 10% funtional. I can place a reminder on the calender but that's about it! No way to system settings.
Sorry if thats teaching you to suck eggs. You obviously know your stuff, just wanted to make it clear.
Ta.
Sent from my HTC One X+ using xda app-developers app

olly2097 said:
Recovery.
Again I know its an issue booting recovery from bootloader. I've read you need the usb in to a pc to make it happen. Obviously that's a no go for me
Click to expand...
Click to collapse
A normally functioning tablet does NOT require you to be plugged in to a PC in order to boot the recovery from the bootloader menu. Maybe you are saying something else here, but I trust you've tried starting the recovery without anything plugged in at all.
Unless you can get the recovery working, the only hope you have is somehow levering up what you have available to gain a privileged thread of execution. Obviously that's going to be pretty challenging.
good luck - you're going to need it.
PS: could you provide a URL to the *wrong* One X gapps download? I think the gapps bundle ships with system libraries - I want to peek at those libs to see if there are any hardcoded block device paths that might explain the queerness you observed. (I can't imagine why this would be the case, but...)

bftb0 said:
A normally functioning tablet does NOT require you to be plugged in to a PC in order to boot the recovery from the bootloader menu. Maybe you are saying something else here, but I trust you've tried starting the recovery without anything plugged in at all.
Unless you can get the recovery working, the only hope you have is somehow levering up what you have available to gain a privileged thread of execution. Obviously that's going to be pretty challenging.
good luck - you're going to need it.
PS: could you provide a URL to the *wrong* One X gapps download? I think the gapps bundle ships with system libraries - I want to peek at those libs to see if there are any hardcoded block device paths that might explain the queerness you observed. (I can't imagine why this would be the case, but...)
Click to expand...
Click to collapse
yeah, tried both ways.
The gapps I downloaded was a while ago. I've deleted it. was for 4.1.1
anyway. I....
Booted to bootloader, selected recovery, pressed power and rammed in the usb cable at the same time.
recovery
now running rom fine after flashing TW recovery via toolkit and mounting to pc.
I cant explain it. it took forever. but thank you

LG G2 Fastboot

Everything I found on this says volume + and power, which kicks me into download mode, not fastboot.
I've gone into adb and typed adb reboot bootloader, but that just restarts the phone and turns in on like normal.
I google the how to enter fastboot mode on LG G2 and can find plenty of post about being stuck in fastboot, but nothing on how to get into fastboot in the first place.
Found a tutorial here about setting up and using fastboot and thought I was set until I got to the part about "and using fastback", where it just says:
Make sure you have android debugging turned on in your phone (not really needed for fastboot but you do need for ADB), plug it into your computer and boot into fastboot mode...
I felt like watching "Much ado about nothing" when Denzel says; "The learned constable is too cunning to be understood"
Any direction is appreciated.

Hmm, I may have written that guide... Just checked and yeah should have been more clear I'll change that up. It should have read the USB debugging was needed for adb (not for fastboot) so when you can issue
adb reboot bootloader
But after that I did mention to check device specific forum for answers on how to get into fastboot/bootloader and being I've never held an lg g2 I took a quick look around.
Unfortunately the only way that I found that people said works every time is to wipe recovery to get into bootloader mode as the recovery you guys currently have disables something due to a patch getting custom recoveries to work
So yeah, I would advice to speak with someone knowledgeable about your specific device before you just wipe recovery
Out of curiosity, is there something specific you need to do with fastboot or are you just curious about your phone?
Sent from my Nexus 7 using XDA Premium 4 mobile app

demkantor said:
Out of curiosity, is there something specific you need to do with fastboot or are you just curious about your phone?
Click to expand...
Click to collapse
the current thing I've been trying to straighten out is that despite being rooted and installing TWRP, I can't install ROMS. I tried CM 11 and Hellfire so that I could put kitkat on, but gave the following:
Error executing updater binary zip.
One of the answers I found said that I had to go back to TWRP 2.3 (I'm using 2.6) and I believe that's where the whole bootloader thing came into play, because it was the way to 'downgrade' -
So then I found Philz touch 6 (as I understand it a mode of CM 11), but here he talked about fastboot and lokifying items. Here's the link:
http://forum.xda-developers.com/showthread.php?t=2554053
In the end it still comes back to the "can't load ROMs" issue. Just want a completely stripped down Kitkat that I can add the stuff I want without the bloatware.
Thanks in advance.(and the thanks button was hit on your reply)

For KitKat you should need a newer recovery with SELinux support which I believe is 2.6.x and newer for twrp, 2.3 I doubt would work if there even is one for your phone
But yes fastboot is often the best way to change recoveries but not the only way.
If there is a flashable.zip you could install new recovery from old
If your current ROM supports the flash image binary you can use a terminal emulator
You can use adb to install
Or even apps from the market
I would look for the latest recovery for your device, twrp, cwm, shouldn't matter so long as its new and then find what way works best changing for your phone.
The update-binary issue is often a sign that you need to change recoveries
Unfortunately without having your device I don't know if I can give you the best answers but feel free to ask
Best of luck!
Sent from my Nexus 4 using XDA Premium 4 mobile app

demkantor said:
Unfortunately without having your device I don't know if I can give you the best answers but feel free to ask
Best of luck!
Click to expand...
Click to collapse
Thanks again. I have adb and the script for loading TWRP 2.6.xx. I unrooted and rerooted the phone, because I wasn't sure how to replace the recovery... Now I think I realize that I could just find another recovery image and place it in the same file as the loki flash and that will flash it (At least that's what I understand at present).
If that's the case, then downloading the Philz touch 6 would work... but not wanting to brick it, I'm still asking and reading.

Hello Guys.
I am having a similar issue. I have a new ROM that will not run because of a faulty lg set up wizard that always force closes and I can not get passed it and a nandroid that for some reason is corrupted. So. This fastboot seems to be a dead end it looks like a quick learning curve of ADB is the only viable answer. I have installed all SDK Manager with ADB Tools and also the required Jarva JDK and LG drivers. The phone is turned on (at the beginning of the faulty setup wizard) In CMD my device is found when typing in 'adb devices' So. I am already to push a new ROM over to the phone.
Do either of you guys know the adb command?
Help would be appreciated.
Thanks

You can't actually flash a new ROM with adb, but you can either push it phone with adb and then flash in recovery. Or if your recovery has an option for adb sideload then use this.
Also setup wizard crashing is usually the fault of wrong gapps or not wiping before flashing a rom
Sent from my Nexus 4 using XDA Premium 4 mobile app

I found that the best way was to load flashify, that did the trick so I could start trying out ROMs... so no on to the next step - finding a 4.4.2 stripped down stock and the LG stuff I actually like.... thanks again.

demkantor said:
You can't actually flash a new ROM with adb, but you can either push it phone with adb and then flash in recovery. Or if your recovery has an option for adb sideload then use this.
Also setup wizard crashing is usually the fault of wrong gapps or not wiping before flashing a rom
Sent from my Nexus 4 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Thanks for the reply!
I know it's not possible to flash a ROM via ADB. I have everything set up, ADB etc, etc. My phone is turned on and adb is seeing it but I can not work out the command to push. Every time I try to push I just get a long list of ADB instructions (I think they are) but nothing gets pushed. I have read lots of instructions on how to make the command but I still must be doing something wrong.
Here are my parameters;-
adb push/C:\Users\dene\Desktop/cm-11-20140210-SNAPSHOT-M3-d802.zip/sdcard
Am I missing some spaces I am not aware of? Are all my slashes the right way round and in the right places? Is my 'sdcard' destination designation correct seeing as there is only internal storage on the G2?
Another problem I am having is that ADB has no problem seeing my sevice EXCEPT when I boot in to recovery (TWRP). When in recovery I lose coms between my device and pc. Hence I can no do TWRP ADB side load (I have tried). I have all the correct LG drivers loaded. Except MTP keeps failing to install? Any ideas?
Not to be mardy about it or hassle you but I am fairly house bound and live out in the country and really require my mobile phone. I have spent many hours trying to figure this out. Any help with the above would be much appreciated?
PS. I did a very thorough wipe, I always do. The gapps are built in to this ROM!
Thanks

dodge3003 said:
Thanks for the reply!
I know it's not possible to flash a ROM via ADB. I have everything set up, ADB etc, etc. My phone is turned on and adb is seeing it but I can not work out the command to push. Every time I try to push I just get a long list of ADB instructions (I think they are) but nothing gets pushed. I have read lots of instructions on how to make the command but I still must be doing something wrong.
Here are my parameters;-
adb push/C:\Users\dene\Desktop/cm-11-20140210-SNAPSHOT-M3-d802.zip/sdcard
Am I missing some spaces I am not aware of? Are all my slashes the right way round and in the right places? Is my 'sdcard' destination designation correct seeing as there is only internal storage on the G2?
Another problem I am having is that ADB has no problem seeing my sevice EXCEPT when I boot in to recovery (TWRP). When in recovery I lose coms between my device and pc. Hence I can no do TWRP ADB side load (I have tried). I have all the correct LG drivers loaded. Except MTP keeps failing to install? Any ideas?
Not to be mardy about it or hassle you but I am fairly house bound and live out in the country and really require my mobile phone. I have spent many hours trying to figure this out. Any help with the above would be much appreciated?
PS. I did a very thorough wipe, I always do. The gapps are built in to this ROM!
Thanks
Click to expand...
Click to collapse
I HAVE SOLVED THE ISSUE! Thanks for your assistance mate but in the end I just went back to stock using this amazing thread:-
http://forum.xda-developers.com/showthread.php?t=2432476
in conjunction with this amazing video;-
http://www.youtube.com/watch?v=IixQjo_hyz8
So! I am now un rooted and back to stock. Time to start the rooting ana ROMing all over again.lol
Thanks

Glad to here!
You need a space after push
But it usually easier not to enter the location of a file while pushing so cd to the directory first like
cd C:\Users.....
Then once there adb push /nameoffile /locationonphone
But if you don't want to cd, I see you have widows, depending on version you can just right click in the folder your file is located and choose open cmd here
Sent from my Nexus 7 using XDA Premium 4 mobile app

Need Help
As I thought I bought LG G2 D-802, but it was D-800 and I accidentally install the lollipop of D802 and now it's in bootlap.... I can only get into fastboot and whenever I try to flash .img of D-800 or D-802 it just stuck at "writing .img"
What to do to unbrick the phone and bring it back to live. I tired the adb and fastboot cmd method on windows 10 and windows 7 but no success. It's just stuck at writing .img file.

[Q] Stuck in Colored Circles screen

I've already searched the forums and found no thread with the solution to my problem. People have had a very similar issue, but not exactly mine, so prior solutions I've found seem to not solve it:
I have a Nexus 7 (2012 WiFi).
It is rooted, clockwork mod.
I have a mac (that seems to not want to detect my Nexus 7 anymore).
I got the update for KitKat, like an idiot, I jumped at it, let it update overnight, and now I'm stuck in the 4 circles loading screen. Since I have CWM, I'm stuck in the CWM recovery mode when I try to do a factory reset. The factory reset does nothing, I was hoping to get back into the stock recovery mode, but have no idea how to get there (nor do I think it's possible).
Keep in mind, I'm semi-tech savvy, but when it comes to "flashing blah blah" I have no idea what the hell anyone is talking about if it's not broken down step by step in layman's terms. If you say, "open the terminal, and type exactly this", then I'm golden, but otherwise, I'm just googling tab after tab to figure out what it means.
As stated above, my mac does not want to even acknowledge the existence of my tablet either with ADK or Android File Transfer. Is there maybe a way I can put a zip on an sd and somehow use an SD reader to mini-usb adapter to sideload a fix? Anyone have any other ideas of how I can fix this issue? I'm not enjoying my Nexus 7 as a paper weight.
Thanks.

Phillustrate said:
I've already searched the forums and found no thread with the solution to my problem. People have had a very similar issue, but not exactly mine, so prior solutions I've found seem to not solve it:
I have a Nexus 7 (2012 WiFi).
It is rooted, clockwork mod.
I have a mac (that seems to not want to detect my Nexus 7 anymore).
I got the update for KitKat, like an idiot, I jumped at it, let it update overnight, and now I'm stuck in the 4 circles loading screen. Since I have CWM, I'm stuck in the CWM recovery mode when I try to do a factory reset. The factory reset does nothing, I was hoping to get back into the stock recovery mode, but have no idea how to get there (nor do I think it's possible).
Keep in mind, I'm semi-tech savvy, but when it comes to "flashing blah blah" I have no idea what the hell anyone is talking about if it's not broken down step by step in layman's terms. If you say, "open the terminal, and type exactly this", then I'm golden, but otherwise, I'm just googling tab after tab to figure out what it means.
As stated above, my mac does not want to even acknowledge the existence of my tablet either with ADK or Android File Transfer. Is there maybe a way I can put a zip on an sd and somehow use an SD reader to mini-usb adapter to sideload a fix? Anyone have any other ideas of how I can fix this issue? I'm not enjoying my Nexus 7 as a paper weight.
Thanks.
Click to expand...
Click to collapse
If your recovery is broken you need to boot into the Bootloader (Hold power until you see the Google logo, then press Vol down.) and then use fastboot to flash a good image from there. You can then do a factory reset etc. You could also do a factory reset from fastboot directly, but you'll want to fix your broken recovery at some point.
Or.. Possibly the better method, since your device is in an unknown state.
https://developers.google.com/android/nexus/images
Get the image FOR YOUR EXACT DEVICE. Don't get the LTE version for the WIFI, etc. Then just run the batch file. It will reset everything (including the internal SD card) and reflash the stock OS. This will leave your bootloader unlocked, with a stock ROM, kernel, recovery. You can flash the custom recovery and supersu.zip if you wish to re-root it.

khaytsus said:
If your recovery is broken you need to boot into the Bootloader (Hold power until you see the Google logo, then press Vol down.) and then use fastboot to flash a good image from there. You can then do a factory reset etc. You could also do a factory reset from fastboot directly, but you'll want to fix your broken recovery at some point.
Or.. Possibly the better method, since your device is in an unknown state.
Get the image FOR YOUR EXACT DEVICE. Don't get the LTE version for the WIFI, etc. Then just run the batch file. It will reset everything (including the internal SD card) and reflash the stock OS. This will leave your bootloader unlocked, with a stock ROM, kernel, recovery. You can flash the custom recovery and supersu.zip if you wish to re-root it.
Click to expand...
Click to collapse
Thank you so much for the response. I apologize for my ignorance: My secondary issue is that my computer does not even recognize when I plug in my Nexus 7. It did previously before my tinkering with it, and before the KitKat update, but now it's like I'm plugging in a brick. I did get to the point of downloading the proper factory image, but it does me no good since I can't load it on there. I don't know how to flash the drive when my computer can't even load anything on to it.
Is it possible to load it through a micro-usb to SD reader adapter? I'm thinking I can load the factory image on to the SD card, and then "sideload" the factory image from there.

To add information so I maybe can get help:
I think the reason my mac doesn't detect it is because I can't get the device into MTP mode so that my mac will see it as a storage device.
I would have to be able to get into the Android OS settings to actually be able to change this setting. I can get into bootload mode, and cwm recovery, but nothing else. I just need some way to get this factory image file onto the Nexus 7, but can't figure out how since this connection does nothing.

Fastboot and recovery do not require any settings configured in the OS. They are independent of the OS. You need to update your sdk on your Mac for the device to be seen in terminal
Sent from my Nexus 5

Pirateghost said:
Fastboot and recovery do not require any settings configured in the OS. They are independent of the OS. You need to update your sdk on your Mac for the device to be seen in terminal
Sent from my Nexus 5
Click to expand...
Click to collapse
It is up to date. It is not recognized either in sdk, android file transfer, or just in finder as a device at all.

You should never see it in a file browser of any sort while in recovery or fastboot mode. Use adb in recovery and fastboot commands in fastboot
Sent from my Nexus 5

I fixed it and recovered it back to 4.2.2, but I will take it!!! NOW I'm going to update to KitKat.
Unfortunately, I can't post links right now since I'm such a new member, but to anyone that has this same issue, I used this guide to get me through it:
Google "nexus 7 factory image restore" written by 2DefMouse. You should find it there.
Also, there's a youtube video counterpart, Google/Youtube this: "How to return to Stock / Updating with Factory Images / Unbrick your Nexus 7"
I'm sure this is fairly common and usual, but for some reason I couldn't figure it out, but to any morons like me, I recommend the guides I followed.
As a tip, for mac, when you type terminal commands, always put the ./ before every "fastboot"... so "./fastboot"
Also, in the guide, it says to type "./fastboot-mac"... I left out the "-mac".
Thanks everyone.

[Q] Droid Razr M not fully booting: Help Please

Hello,
Problem:
factory reset my Droid RAZR M with the hope to resolve in-call audio problems (very low ear piece volume at full). When I rebooted the phone the Welcome screen appeared asking for a language choice. Chose english US. The Message: "Please wait, This may take a few minutes" appeared with a spinning icon. But nothing else ever happens. The phone never moves beyond this selection.
I have android-sdk (Linux setup) installed on my computer in order to use the suite of tools like fastboot and adb. The tools work, in that I can see the phone, pull data, upload to the phone and even get a command shell on the phone. However in order for adb to recognize the phone I have to put the phone in "BT Tools" mode. In "AP fastboot" mode fastboot sees the phone. As far as I remember USB debugging was turned on.
I do not have a recovery image installed.
The phone has Kitkat 4.4.2 ver 183.46.10 and is rooted with TowelRoot. I just unlocked the bootloader today via motoapocalypse package. Status of the phone is unlocked Code 3
I also removed some unused apps - like NFL and a few other space and bandwidth consuming apps that I will never use.
I'd like to get this phone to work again. Is there any hope?
Please advise and thanks for reading.

You can flash custom recovery via fastboot and then custom ROM or flash stock ROM via RSD. Guide is in first thread in general section.
http://forum.xda-developers.com/showthread.php?t=2869432
[GUIDE][FAQ][DIY][KK] How to Root, Boot Unlock & More

Thanks for the pointer. I gather that RSD is a Windows based app. At the present time I do not have a Windows computer. So I took a shot at the job using fastboot, adb and all as found in the android-sdk. Did the steps as described in the flashing post. Now all I ever see is the "Bootloader unlocked warning message" and the phone never progresses beyond the warning. I disassembled the phone, to disconnect the battery -- hoping for a reset miracle. No change after reassembly. Given the latest state of the phone as described above, is there any chance of reviving this phone now that it's stuck at the bootloader warning?
(I read a post about a Motorola Factory Cable -- and if I understand the factory cable puts the phone in a special mode for flashing looking into this option).
I am out to learn and am not afraid of poking around -- so at this point I have no more to lose.
Would the Windows computer make the difference? Using linux mint atm.
Klen2 said:
You can flash custom recovery via fastboot and then custom ROM or flash stock ROM via RSD. Guide is in first thread in general section.
http://forum.xda-developers.com/showthread.php?t=2869432
[GUIDE][FAQ][DIY][KK] How to Root, Boot Unlock & More
Click to expand...
Click to collapse

diordnAMRZAR said:
Thanks for the pointer. I gather that RSD is a Windows based app. At the present time I do not have a Windows computer. So I took a shot at the job using fastboot, adb and all as found in the android-sdk. Did the steps as described in the flashing post. Now all I ever see is the "Bootloader unlocked warning message" and the phone never progresses beyond the warning. I disassembled the phone, to disconnect the battery -- hoping for a reset miracle. No change after reassembly. Given the latest state of the phone as described above, is there any chance of reviving this phone now that it's stuck at the bootloader warning?
(I read a post about a Motorola Factory Cable -- and if I understand the factory cable puts the phone in a special mode for flashing looking into this option).
I am out to learn and am not afraid of poking around -- so at this point I have no more to lose.
Would the Windows computer make the difference? Using linux mint atm.
Click to expand...
Click to collapse
You can try using SBF_FLASH or mFastboot-v2 (which has a linux version) to flash the system.img .

SOLVED: [Q] Droid Razr M not fully booting: Help Please
That worked. Thanks! So the difference between the SDK fastboot and the one in the link provided (mfastboot-V2): the linux-fastboot seems to be smarter about uploading the larger image files to the flashable device (guessing). I am sure I did "flashboot flash system system.img" with the flashboot util from the SDK.
@ATTACK do you have the source for that version of fastboot or patches? Would like to have a look.
Thanks again! Got an unlocked rooted working Droid RAZR M!

diordnAMRZAR said:
That worked. Thanks! So the difference between the SDK fastboot and the one in the link provided (mfastboot-V2): the linux-fastboot seems to be smarter about uploading the larger image files to the flashable device (guessing). I am sure I did "flashboot flash system system.img" with the flashboot util from the SDK.
@ATTACK do you have the source for that version of fastboot or patches? Would like to have a look.
Thanks again! Got an unlocked rooted working Droid RAZR M!
Click to expand...
Click to collapse
Your guess is correct, mfastboot allows you to flash larger system.img's that wont otherwise flash in fastboot.
As for sources... I have no idea who created mfastboot or where it came from. It's just one of those things that get's passed around the internet.

ATTACK said:
Your guess is correct, mfastboot allows you to flash larger system.img's that wont otherwise flash in fastboot.
As for sources... I have no idea who created mfastboot or where it came from. It's just one of those things that get's passed around the internet.
Click to expand...
Click to collapse
Well I'm happy to have the utility that works. Can thank you enough -- or the creators. Found it also on goggle code after a properly crafted search string. All this for an in-call audio problem that only worsened after I took the phone apart. Still works on speaker mode though so that's good enough -- at low volume. And I learned a few things. One interesting thing: The shell prompt got rewritten to say ${USER}@scorpion_mini/ after flashing the system.img. Pretty sure it only said android prior to re-flashing . And the getprop helper app is a new thing for me.
Feel like a kid all over again exploring this little device.