**IMPORTANT**
Read this thoroughly before you attempt any of it. The steps found herein will wipe out any data remaining on the partition for which it's used. If a partition has lost it's formatting, chances are the data is lost anyway, so there's not much more you can lose. This should be thought of as a last resort. Do not attempt this until you have tried everything else.
In many cases, just wiping the affected partition in recovery is enough to fix the problem. If not, continue reading.
If it's your sdcard that needs to be mounted, there is one thing you can try that might work in most cases.
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] echo /dev/block/mmcblk0p12 >> /sys/devices/platform/usb_mass_storage/lun0/file
Your computer will probably respond that the volume/device needs formatted before using it. This will erase everything left on the sdcard, as will anything else you attempt in this thread.
* Choose a quick format (if possible) and format it as "fat32", block size "4096".
If that doesn't work...
You'll have to reset your partition table, just in case (this step is optional but it doesn't hurt to do it anyway).
You'll need to be in fastboot:
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] idme bootmode 4002
[COLOR=Gray]~ #[/COLOR] reboot
(*COTR recovery doesn't have idme so you'll have to use the recovery itself to reboot into the bootloader)
Once in fastboot, enter the following commands...
Code:
[COLOR=Gray]$[/COLOR] fastboot oem format
[COLOR=Gray]$[/COLOR] fastboot oem idme bootmode 5001
[COLOR=Gray]$[/COLOR] fastboot reboot
With your partition table reset, it's time to print your partition table for reference.
For this, your device must be booted into recovery.
To print your partition table:
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] print
This will print the layout of your partitions 1-12. It should look something like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If you receive an error stating that parted can't be found, you need to find and download it and enter the following commands, or update your recovery...
Code:
[COLOR=Gray]$[/COLOR] adb push /path/to/parted /sbin/parted
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] chown 0.0 /sbin/parted
[COLOR=Gray]~ #[/COLOR] chown 755 /sbin/parted
(*replace "/path/to/parted" with the full path to the parted binary downloaded to your computer)
Once you have your partition table printed out, copy and save it to a text file for later use.
When looking at the partition table, pay close attention to the file systems of the system, userdata, cache and media partitions. System, data and cache, should have an "ext4" formatting, while media should have a "fat32" formatting. The partitions that are missing the proper formatting are the ones you need to focus on because they need to be removed and repartitioned.
----------------------------------------------------------------------------------------------------------------------------------------
NEVER MESS WITH ANYTHING OTHER THAN SYSTEM, DATA, CACHE AND MEDIA!!!
----------------------------------------------------------------------------------------------------------------------------------------
The following, are the steps to repartition the system, data, and cache partitions. Media (sdcard) will have it's own steps so don't get them mixed up. These same steps will be used for each of the system data and cache partitions except you'll substitute the variables (in green) with the values for that particular partition. Be careful NOT to get the any of numbers mixed up or confused or you could potentially do serious damage to your device.
Code:
[COLOR=Gray]$[/COLOR] abd shell
[COLOR=Gray]~ #[/COLOR] umount [COLOR=SeaGreen]"directory_name"[/COLOR] [COLOR=Red]<---- This command is to make sure the volume isn't already mounted. If you get an error, it just means there is no volume mounted. Disregard.[/COLOR]
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] rm [COLOR=SeaGreen]"partition_number"[/COLOR]
[COLOR=Gray](parted)[/COLOR] mkpart primary [COLOR=SeaGreen]"startblock" "endblock"[/COLOR]
[COLOR=Gray](parted)[/COLOR] name [COLOR=SeaGreen]"partition_number" "partition_name"[/COLOR]
[COLOR=Gray](parted)[/COLOR] quit
[COLOR=Gray]~ #[/COLOR] mke2fs -t ext4 /dev/block/mmcblk0p[COLOR=SeaGreen]"partition_number"[/COLOR]
[COLOR=Gray]~ #[/COLOR] mount [COLOR=SeaGreen]"directory_name"[/COLOR]
The values for the previous command variables are as follows...
SYSTEM
-------------------------------
"partition_number"= 9
"directory_name" = /system
"partition_name" = system
"startblock" = 312
"endblock" = 849
DATA
-------------------------------
"partition_number"= 10
"directory_name" = /data
"partition_name" = userdata
"startblock" = 849
"endblock" = 2041
CACHE
-------------------------------
"partition_number"= 11
"directory_name" = /cache
"partition_name" = cache
"startblock" = 2041
"endblock" = 2309
For example, in order to fix the DATA partition, the commands would be written like this...
Code:
[COLOR=Gray]$[/COLOR] abd shell
[COLOR=Gray]~ #[/COLOR] umount /data
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] rm 10
[COLOR=Gray](parted)[/COLOR] mkpart primary 849 2041
[COLOR=Gray](parted)[/COLOR] name 10 userdata
[COLOR=Gray](parted)[/COLOR] quit
[COLOR=Gray]~ #[/COLOR] mke2fs -t ext4 /dev/block/mmcblk0p10
[COLOR=Gray]~ #[/COLOR] mount /data
The following are the steps to repartition the media (sdcard) partition.
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] umount /sdcard [COLOR=Red]<----Same as before. If you receive an error on this command, just disregard it.[/COLOR]
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] rm 12
[COLOR=Gray](parted)[/COLOR] mkpartfs primary fat32 2309 7690
[COLOR=Gray](parted)[/COLOR] rm 12
[COLOR=Gray](parted)[/COLOR] mkpart primary 2309 7690
[COLOR=Gray](parted)[/COLOR] name 12 media
[COLOR=Gray](parted)[/COLOR] quit
[COLOR=Gray]~ #[/COLOR] mount /sdcard
Once again, any partitions on which these commands are used, will lose any data left on them, but chances are it's your only option. Pay very close attention to what you are doing and be very cautious of typos. Accidentally entering /dev/block/mmcblk0p2' instead of "/dev/block/mmcblk0p12" will brick your device, to the point of needing to pull the back cover off and shorting it...well...let's just say you don't want to have to do that.
Afterwards you should be able to mount the effected partitions in recovery.
Be careful, and good luck.
Refrences:
http://forum.xda-developers.com/showpost.php?p=26285877&postcount=12
http://forum.xda-developers.com/showthread.php?t=1651413
http://forum.xda-developers.com/showthread.php?t=1497900
Thanks to kinfauns for showing me that it isn't always necessary to create an "ext2" file system first and then convert it to "ext4", and for showing me how to get rid of the pesky msftres flags.
Great work, sticky and Thank You.
Thank you bigjoe2675 and thank you soupmagnet for you fine work!!
soupmagnet said:
**IMPORTANT**
Read this thoroughly before you attempt any of it. The steps found herein will wipe out any data remaining on the partition for which it's used. If a partition has lost it's formatting, chances are the data is lost anyway, so there's not much more you can lose. This should be thought of as a last resort. Do not attempt this until you have tried everything else.
In many cases, just wiping the affected partition in recovery is enough to fix the problem. If not, continue reading.
If it's your sdcard that needs to be mounted, there is one thing you can try that might work in most cases.
Code:
[COLOR="Gray"]$[/COLOR] adb shell
[COLOR="Gray"]~ #[/COLOR] echo /dev/block/mmcblk0p12 >> /sys/devices/platform/usb_mass_storage/lun0/file
Your computer will probably respond that the volume/device needs formatted before using it. This will erase everything left on the sdcard, as will anything else you attempt in this thread.
* Choose a quick format (if possible) and format it as "fat32", block size "4096".
If that doesn't work...
You'll have to reset your partition table, just in case (this step is optional but it doesn't hurt to do it anyway).
You'll need to be in fastboot:
Code:
[COLOR="Gray"]$[/COLOR] adb shell
[COLOR="Gray"]~ #[/COLOR] idme bootmode 4002
[COLOR="Gray"]~ #[/COLOR] reboot
(*COTR recovery doesn't have idme so you'll have to use the recovery itself to reboot into the bootloader)
Once in fastboot, enter the following commands...
Code:
[COLOR="Gray"]$[/COLOR] fastboot oem format
[COLOR="Gray"]$[/COLOR] fastboot oem idme bootmode 5001
[COLOR="Gray"]$[/COLOR] fastboot reboot
With your partition table reset, it's time to print your partition table for reference.
For this, your device must be booted into recovery.
To print your partition table:
Code:
[COLOR="Gray"]$[/COLOR] adb shell
[COLOR="Gray"]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR="Gray"](parted)[/COLOR] print
This will print the layout of your partitions 1-12. It should look something like this:
View attachment 1421197
If you receive an error stating that parted can't be found, you need to find and download it and enter the following commands, or update your recovery...
Code:
[COLOR="Gray"]$[/COLOR] adb push /path/to/parted /sbin/parted
[COLOR="Gray"]$[/COLOR] adb shell
[COLOR="Gray"]~ #[/COLOR] chown 0.0 /sbin/parted
[COLOR="Gray"]~ #[/COLOR] chown 755 /sbin/parted
(*replace "/path/to/parted" with the full path to the parted binary downloaded to your computer)
Once you have your partition table printed out, copy and save it to a text file for later use.
When looking at the partition table, pay close attention to the file systems of the system, userdata, cache and media partitions. System, data and cache, should have an "ext4" formatting, while media should have a "fat32" formatting. The partitions that are missing the proper formatting are the ones you need to focus on because they need to be removed and repartitioned.
----------------------------------------------------------------------------------------------------------------------------------------
NEVER MESS WITH ANYTHING OTHER THAN SYSTEM, DATA, CACHE AND MEDIA!!!
----------------------------------------------------------------------------------------------------------------------------------------
The following, are the steps to repartition the system, data, and cache partitions. Media (sdcard) will have it's own steps so don't get them mixed up. These same steps will be used for each of the system data and cache partitions except you'll substitute the variables (in green) with the values for that particular partition. Be careful NOT to get the any of numbers mixed up or confused or you could potentially do serious damage to your device.
Code:
[COLOR="Gray"]$[/COLOR] abd shell
[COLOR="Gray"]~ #[/COLOR] umount [COLOR="SeaGreen"]"directory_name"[/COLOR]
[COLOR="Gray"]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR="Gray"](parted)[/COLOR] rm [COLOR="SeaGreen"]"partition_number"[/COLOR]
[COLOR="Gray"](parted)[/COLOR] mkpart primary [COLOR="SeaGreen"]"startblock" "endblock"[/COLOR]
[COLOR="Gray"](parted)[/COLOR] name [COLOR="SeaGreen"]"partition_number" "partition_name"[/COLOR]
[COLOR="Gray"](parted)[/COLOR] quit
[COLOR="Gray"]~ #[/COLOR] mke2fs -t ext4 /dev/block/mmcblk0p[COLOR="SeaGreen"]"partition_number"[/COLOR]
[COLOR="Gray"]~ #[/COLOR] mount [COLOR="SeaGreen"]"directory_name"[/COLOR]
The values for the previous command variables are as follows...
SYSTEM
-------------------------------
"partition_number"= 9
"directory_name" = /system
"partition_name" = system
"startblock" = 312
"endblock" = 849
DATA
-------------------------------
"partition_number"= 10
"directory_name" = /data
"partition_name" = userdata
"startblock" = 849
"endblock" = 2041
CACHE
-------------------------------
"partition_number"= 11
"directory_name" = /cache
"partition_name" = cache
"startblock" = 2041
"endblock" = 2309
For example, in order to fix the DATA partition, the commands would be written like this...
Code:
[COLOR="Gray"]$[/COLOR] abd shell
[COLOR="Gray"]~ #[/COLOR] umount /data
[COLOR="Gray"]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR="Gray"](parted)[/COLOR] rm 10
[COLOR="Gray"](parted)[/COLOR] mkpart primary 312 849
[COLOR="Gray"](parted)[/COLOR] name 10 userdata
[COLOR="Gray"](parted)[/COLOR] quit
[COLOR="Gray"]~ #[/COLOR] mke2fs -t ext4 /dev/block/mmcblk0p9
[COLOR="Gray"]~ #[/COLOR] mount /data
The following are the steps to repartition the media (sdcard) partition.
Code:
[COLOR="Gray"]$[/COLOR] adb shell
[COLOR="Gray"]~ #[/COLOR] umount /sdcard
[COLOR="Gray"]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR="Gray"](parted)[/COLOR] rm 12
[COLOR="Gray"](parted)[/COLOR] mkpartfs primary fat32 2309 7690
[COLOR="Gray"](parted)[/COLOR] rm 12
[COLOR="Gray"](parted)[/COLOR] mkpart primary 2309 7690
[COLOR="Gray"](parted)[/COLOR] name 12 media
[COLOR="Gray"](parted)[/COLOR] quit
[COLOR="Gray"]~ #[/COLOR] mount /sdcard
Once again, any partitions on which these commands are used, will lose any data left on them, but chances are it's your only option. Pay very close attention to what you are doing and be very cautious of typos. Accidentally entering /dev/block/mmcblk0p2' instead of "/dev/block/mmcblk0p12" will brick your device, to the point of needing to pull the back cover off and shorting it...well...let's just say you don't want to have to do that.
Afterwards you should be able to mount the effected partitions in recovery.
Be careful, and good luck.
Refrences:
http://forum.xda-developers.com/showpost.php?p=26285877&postcount=12
http://forum.xda-developers.com/showthread.php?t=1651413
http://forum.xda-developers.com/showthread.php?t=1497900
Thanks to kinfauns for showing me that it isn't always necessary to create an "ext2" file system first and then convert it to "ext4", and for showing me how to get rid of the pesky msftres flags.
Click to expand...
Click to collapse
The first method doesn't work, so as you said, i'l have to boot into fastboot.
But it says "idme not found"
Please help.
Noob.
I have attached some pics for more information.
A guide for getting into fastboot:
http://forum.xda-developers.com/showthread.php?t=1668159
[edit:] BTW This guide is for the Kindle Fire. On other devices your partition layout will likely be different. Try the forums for your particular device.
"That's a special kind of stupid. The kind that makes me laugh."
I didnt use this guide (although I read it all and was about to go this route) big thanks!
Got a question though , at one point I had (i guess temp root privelidges) because I sideloaded but in root explorer I didnt have su , anyway , in KFU there was a section that said you could change mount to write , although thats nots root , would I have been able to use the adb to push commands to the kindle? I wanted to get into the file explorer and just use usb mass storage to put files in and maybe gain root that way ?
*I realize :"That's a special kind of stupid. The kind that makes me laugh."but I thought Id ask anyway!!!
Vintage144 said:
I didnt use this guide (although I read it all and was about to go this route) big thanks!
Got a question though , at one point I had (i guess temp root privelidges) because I sideloaded but in root explorer I didnt have su , anyway , in KFU there was a section that said you could change mount to write , although thats nots root , would I have been able to use the adb to push commands to the kindle? I wanted to get into the file explorer and just use usb mass storage to put files in and maybe gain root that way ?
*I realize :"That's a special kind of stupid. The kind that makes me laugh."but I thought Id ask anyway!!!
Click to expand...
Click to collapse
LOL that does make me laugh, but not for reasons you'd think. Actually the USB mass storage is only the sdcard (media) partition. Mounting the sdcard to USB or side loading apps only gives you access to the sdcard, which you already have write permissions for anyway. You can't cross over to other partitions without mounting them first and you need to be the root user to do that. With the sdcard being secluded from the system partition, in order to get root permissions you need to be the root user or have write permissions on the system partition, at least temporarily.
On the original Kindle Fire you can get that through custom recovery, which has root permissions, or through some exploit found in Gingerbread. That's what makes Pokey9000's 'fbmode' so slick. It gives users access to fastboot, which in turn gives them access to flash a custom recovery and gain root permissions (KFU uses this) long enough to write SU and Superuser.apk to the system partition, eliminating the need for an exploit in Gingerbread.
These days, root exploits in Android are few and far between and they are getting patched pretty regularly, so the ability to install and boot onto custom recovery is pretty valuable. I imagine that's why Amazon used OMAP HS on the second generation devices in an (obviously feeble) attempt to patch such a gaping hole in their security.
The only reason. I say this , is because on my a500 I have a microsd card that I can transfer files to and from (granted I have root) however I had access to android folders ,I just thought as a last resort I could gain access that way,
I've noticed something funny on xda ,99% of people who have problems here have the same response "my friends device isn't working" I'm betting that means there device and instead of actually reading all the material available they just read one post and tried whatever the op said not realizing there's a process to everything the devs do and reason why we must follow directions! Writing can you fix my fubar is bs ,there's tons of info in hear ya just gotta look for it
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
Well I tried all this. At the beginning it worked. But on every reboot or use, its just doesn't reconise the sdcard anymore.
format/reinstall/ play with it 10 minute/freeze/sd card cant read
format/reinstall/play with it 5 minuts/freeze/sdcant read
etc
at the end nothing's working.
On my last attemp I put the original rom.
Amazone give me a new one. sd card has probably bad sector.
---- Is there a way to prevent this trouble ?? ---
thanks
oVeRdOsE. said:
Well I tried all this. At the beginning it worked. But on every reboot or use, its just doesn't reconise the sdcard anymore.
format/reinstall/ play with it 10 minute/freeze/sd card cant read
format/reinstall/play with it 5 minuts/freeze/sdcant read
etc
at the end nothing's working.
On my last attemp I put the original rom.
Amazone give me a new one. sd card has probably bad sector.
---- Is there a way to prevent this trouble ?? ---
thanks
Click to expand...
Click to collapse
One way to check to see if your sdcard has bad sectors is with the following command:
Code:
adb shell dd if=/sdcard of=/dev/null
If it doesn't respond for more than 10 minutes, then you probably have bad sectors. But I'm guessing that might not the case since you are able to format it in the first place. Are you playing a game or something when this happens?
Sent from my KFHD using Tapatalk 2
Looking for an opinion
Hey there, very well written post.
My situation is regarding my Nexus Q. I attempted to flash a CM10.1 rom to it and something went wrong. I have it back to stock, but I think my partitions need to be reset, and was hoping someone could advise me based on my screenshot. While in Recovery, I get told that the SD Card only has 15mb of space, and it cannot mount /cache to perform a logcat. I notice from the OP screenshot that most of the other partions have ext4 beside but mine do not.
Should I follow your guide to re partition my unit?
Cheers
HomeR365 said:
Hey there, very well written post.
My situation is regarding my Nexus Q. I attempted to flash a CM10.1 rom to it and something went wrong. I have it back to stock, but I think my partitions need to be reset, and was hoping someone could advise me based on my screenshot. While in Recovery, I get told that the SD Card only has 15mb of space, and it cannot mount /cache to perform a logcat. I notice from the OP screenshot that most of the other partions have ext4 beside but mine do not.
Should I follow your guide to re partition my unit?
Cheers
Click to expand...
Click to collapse
Probably, but with GREAT discernment. You need to learn about your device's partitions and what they're for. And you definitely need to learn what the commands are doing so you understand what's going on. I wouldn't suggest just trying it out and hoping for the best.
This is awesome. Thanks so much. Bookmarked for future reference after spending hours on this.
stuck in orange logo boot
Hello, total noob here. Ok i rooted my kindle fire. rebooted and it started with kindle fire logo in blue color. Then I connect to my pc it showed it got connected.I put in new zip of cynogenmod jelly bean. All good rebooted with kindle fire logo orange color. No google apps, now i connect it to PC and it wont show kindle. So i downloaded the Gapps directly in kindle. rebooted for recovery but it rebooted to jelly bean. Blue kindle fire wont show up. I need to get into TWRP so that I can install Gaapps. trying for three days. read many posted. holding power button for 20 secs till it shuts down. then connecting usb to PC it restart but with orange fire logo. Added some lines 4000 or 4001 under tools menu in utility folder, run the cmd from the tools folder.... nothing changed. tried. RAN KFU again and it shows status offline, rooted no, and boot menu unkwon. Ran ADB straight shows waiting for device. So my question is how can I get back to recovery or blue logo where I can go and reset or reinstall or atleast install just Gaaps. tried install just random games APKs. It wont let it install. Please Help. Dont know much linux or DOS either.
thanks this help alot thanks a million
sir i have a arise rowdy t1+ phone its board is sp6820gb_7620 and cpu id is 8810 cpu frequency is 1ghz and ram is 512mb with mali 300 gpu,
android version is 2.3.6 and kernal version is 2.6.35.7 [email protected] #7, software version is mocordroid2.3.6.w12.20_p20.01_20130715.130506, hardware version is 1.1.0. my problem is that my phone has only 128 mb of internal memory and when i tried to edit vold.fstab to swap its memory with memory card it stopped detecting sd card when turned on but when in recovery mode sd is shown present, i think its very similar to karbonn a1+ in hardware and software part so can you please help me with my phone?
thank you so much !!!!!!!! its awesome
nitingoel2 said:
sir i have a arise rowdy t1+ phone its board is sp6820gb_7620 and cpu id is 8810 cpu frequency is 1ghz and ram is 512mb with mali 300 gpu,
android version is 2.3.6 and kernal version is 2.6.35.7 [email protected] #7, software version is mocordroid2.3.6.w12.20_p20.01_20130715.130506, hardware version is 1.1.0. my problem is that my phone has only 128 mb of internal memory and when i tried to edit vold.fstab to swap its memory with memory card it stopped detecting sd card when turned on but when in recovery mode sd is shown present, i think its very similar to karbonn a1+ in hardware and software part can you please help me with my phone?
Click to expand...
Click to collapse
This is a kindle fire forum friend
Sent from my Amazon Kindle Fire using Tapatalk
soupmagnet said:
**IMPORTANT**
Read this thoroughly before you attempt any of it. The steps found herein will wipe out any data remaining on the partition for which it's used. If a partition has lost it's formatting, chances are the data is lost anyway, so there's not much more you can lose. This should be thought of as a last resort. Do not attempt this until you have tried everything else.
In many cases, just wiping the affected partition in recovery is enough to fix the problem. If not, continue reading.
If it's your sdcard that needs to be mounted, there is one thing you can try that might work in most cases.
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] echo /dev/block/mmcblk0p12 >> /sys/devices/platform/usb_mass_storage/lun0/file
Your computer will probably respond that the volume/device needs formatted before using it. This will erase everything left on the sdcard, as will anything else you attempt in this thread.
* Choose a quick format (if possible) and format it as "fat32", block size "4096".
If that doesn't work...
You'll have to reset your partition table, just in case (this step is optional but it doesn't hurt to do it anyway).
You'll need to be in fastboot:
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] idme bootmode 4002
[COLOR=Gray]~ #[/COLOR] reboot
(*COTR recovery doesn't have idme so you'll have to use the recovery itself to reboot into the bootloader)
Once in fastboot, enter the following commands...
Code:
[COLOR=Gray]$[/COLOR] fastboot oem format
[COLOR=Gray]$[/COLOR] fastboot oem idme bootmode 5001
[COLOR=Gray]$[/COLOR] fastboot reboot
With your partition table reset, it's time to print your partition table for reference.
For this, your device must be booted into recovery.
To print your partition table:
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] print
This will print the layout of your partitions 1-12. It should look something like this:
View attachment 1421197
If you receive an error stating that parted can't be found, you need to find and download it and enter the following commands, or update your recovery...
Code:
[COLOR=Gray]$[/COLOR] adb push /path/to/parted /sbin/parted
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] chown 0.0 /sbin/parted
[COLOR=Gray]~ #[/COLOR] chown 755 /sbin/parted
(*replace "/path/to/parted" with the full path to the parted binary downloaded to your computer)
Once you have your partition table printed out, copy and save it to a text file for later use.
When looking at the partition table, pay close attention to the file systems of the system, userdata, cache and media partitions. System, data and cache, should have an "ext4" formatting, while media should have a "fat32" formatting. The partitions that are missing the proper formatting are the ones you need to focus on because they need to be removed and repartitioned.
----------------------------------------------------------------------------------------------------------------------------------------
NEVER MESS WITH ANYTHING OTHER THAN SYSTEM, DATA, CACHE AND MEDIA!!!
----------------------------------------------------------------------------------------------------------------------------------------
The following, are the steps to repartition the system, data, and cache partitions. Media (sdcard) will have it's own steps so don't get them mixed up. These same steps will be used for each of the system data and cache partitions except you'll substitute the variables (in green) with the values for that particular partition. Be careful NOT to get the any of numbers mixed up or confused or you could potentially do serious damage to your device.
Code:
[COLOR=Gray]$[/COLOR] abd shell
[COLOR=Gray]~ #[/COLOR] umount [COLOR=SeaGreen]"directory_name"[/COLOR] [COLOR=Red]<---- This command is to make sure the volume isn't already mounted. If you get an error, it just means there is no volume mounted. Disregard.[/COLOR]
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] rm [COLOR=SeaGreen]"partition_number"[/COLOR]
[COLOR=Gray](parted)[/COLOR] mkpart primary [COLOR=SeaGreen]"startblock" "endblock"[/COLOR]
[COLOR=Gray](parted)[/COLOR] name [COLOR=SeaGreen]"partition_number" "partition_name"[/COLOR]
[COLOR=Gray](parted)[/COLOR] quit
[COLOR=Gray]~ #[/COLOR] mke2fs -t ext4 /dev/block/mmcblk0p[COLOR=SeaGreen]"partition_number"[/COLOR]
[COLOR=Gray]~ #[/COLOR] mount [COLOR=SeaGreen]"directory_name"[/COLOR]
The values for the previous command variables are as follows...
SYSTEM
-------------------------------
"partition_number"= 9
"directory_name" = /system
"partition_name" = system
"startblock" = 312
"endblock" = 849
DATA
-------------------------------
"partition_number"= 10
"directory_name" = /data
"partition_name" = userdata
"startblock" = 849
"endblock" = 2041
CACHE
-------------------------------
"partition_number"= 11
"directory_name" = /cache
"partition_name" = cache
"startblock" = 2041
"endblock" = 2309
For example, in order to fix the DATA partition, the commands would be written like this...
Code:
[COLOR=Gray]$[/COLOR] abd shell
[COLOR=Gray]~ #[/COLOR] umount /data
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] rm 10
[COLOR=Gray](parted)[/COLOR] mkpart primary 849 2041
[COLOR=Gray](parted)[/COLOR] name 10 userdata
[COLOR=Gray](parted)[/COLOR] quit
[COLOR=Gray]~ #[/COLOR] mke2fs -t ext4 /dev/block/mmcblk0p10
[COLOR=Gray]~ #[/COLOR] mount /data
The following are the steps to repartition the media (sdcard) partition.
Code:
[COLOR=Gray]$[/COLOR] adb shell
[COLOR=Gray]~ #[/COLOR] umount /sdcard [COLOR=Red]<----Same as before. If you receive an error on this command, just disregard it.[/COLOR]
[COLOR=Gray]~ #[/COLOR] parted /dev/block/mmcblk0
[COLOR=Gray](parted)[/COLOR] rm 12
[COLOR=Gray](parted)[/COLOR] mkpartfs primary fat32 2309 7690
[COLOR=Gray](parted)[/COLOR] rm 12
[COLOR=Gray](parted)[/COLOR] mkpart primary 2309 7690
[COLOR=Gray](parted)[/COLOR] name 12 media
[COLOR=Gray](parted)[/COLOR] quit
[COLOR=Gray]~ #[/COLOR] mount /sdcard
Once again, any partitions on which these commands are used, will lose any data left on them, but chances are it's your only option. Pay very close attention to what you are doing and be very cautious of typos. Accidentally entering /dev/block/mmcblk0p2' instead of "/dev/block/mmcblk0p12" will brick your device, to the point of needing to pull the back cover off and shorting it...well...let's just say you don't want to have to do that.
Afterwards you should be able to mount the effected partitions in recovery.
Be careful, and good luck.
Refrences:
http://forum.xda-developers.com/showpost.php?p=26285877&postcount=12
http://forum.xda-developers.com/showthread.php?t=1651413
http://forum.xda-developers.com/showthread.php?t=1497900
Thanks to kinfauns for showing me that it isn't always necessary to create an "ext2" file system first and then convert it to "ext4", and for showing me how to get rid of the pesky msftres flags.
Click to expand...
Click to collapse
Now, I get the error that the sdcard isn't mounted in root explorer, but I can still find all of the contents of the sdcard under /storage/emulated/0. Is there any reason for this? I was thinking of simply copying everything to a new folder named sdcard (because the old folder turned into a file with a filesize of -1 bytes) but then the newly created folder had the same problem. Whenever I tapped on it it gave me the same error, "The SD card in't mounted". I'm on a Nexus 4, any help?
Cannot solve this issue
I've had it with messing this for my 1st gen kindle fire, for the last 5 weeks I've been trying to unbrick it and nothing works. I can connect to the device using Super ADB Tool but trying to load anything produces the and I get "- exec '/system/bin/sh' failed" messages using the command prompt.
Related
Okay, so I have used four recovery images since I have had my G1 and now the myTouch 3g. Two from Cyanogen when I had my G1. When I rooted my MT3G I had Amon_Ra's 1.2.0G and 1.2.1G. Today I flashed Twisted's Recovery Image. Both Amon's and Twisted's give the option to partition your memory card (Fat32, Ext2, and Linux-Swap). I love that because it makes things so much easier. Well, getting to the point of this thread. Are there any recovery images that format just the ext. part of our memory cards? Is that even possible? I ask because I flash different ROM's every few days and I like to wipe my ext3 to give it a fresh start for each ROM. I know it's just a few codes through ADB, but I'm sure I'm not alone when I say I like to be lazy. That would make things so much easier. Thanks in advance for any feedback.
To wipe your ext3 data ..
Code:
adb remount
adb shell rm -rf /system/sd/*
adb shell rm -rf /data/dalvik-cache/*
This should be the last thing you do before you flash as it will stop stuff from working properly!
In case you need more information: Connect your device and type "adb shell" and then do "mount | grep mmcblk0p2", this will show you where your ext2/3 partition is mounted (mmcblk0 represents your sd card, and p2 is the second partition) :
Code:
# mount | grep mmcblk0p2
mount | grep mmcblk0p2
/dev/block/mmcblk0p2 on /system/sd type ext2 (rw,noatime,nodiratime,errors=conti
nue)
/dev/block/mmcblk0p2 on /data/dalvik-cache type ext2 (rw,noatime,nodiratime,erro
rs=continue)
exit
I've seen a lot of threads detailing how to create an Ext4 partition using Gparted but if you don't want to download the image and would rather do it all on your phone, here's how:
This entire procedure should take less than 5min so you can go back to messing with your phone in other ways.
REQUIRES:
CLOCKWORK MOD RECOVERY
ADB
FINGERS
I am not responsible for any damage done to your phone doing this process. =.=
1. Download the zip file provided.
2. Extract the zip file to the same folder you have ADB in. (You should now have a folder named ext4 in the same folder you have ADB)
3. Reboot the phone into MAGDLR. Then select the option to boot into the recovery.
4. Make sure that /system/ is mounted using the option to mount partition in Clockwork Recovery.
5. Open a command (cmd) prompt and cd into your folder with ADB.
6. Run these commands in the command prompt. (Commands are in BOLD)
adb push ext4 /system/etc/
adb shell
parted /dev/block/mmcblk0
print (make note of the total size of your partition here)
resize 1 0 xxxx (where xxxx is the size you want for your FAT32 partition. It should equal total size of your partition that you gleaned from print minus 1024 for the ext4 partition you're about to set up)
mkpartfs primary ext2 xxxx yyyy (where xxxx is where your previous partition ended and yyyy is the total size of your sdcard)
.... (Let it do its thing. Shouldn't take more than a minute)
print (Make sure that everything is correct: You have a fat32 partition running from 0 to xxxx and an ext2 partition running from xxxx to the total size of your partition)
quit
Now to utilize the two files we previously pushed to /system/etc/
chmod 777 /system/etc/tune2fs
chmod 777 /system/etc/e2fsck
/system/etc/tune2fs -j /dev/block/mmcblk0p2 <- You now have ext3
/system/etc/tune2fs -O extents,uninit_bg,dir_index /dev/block/mmcblk0p2 (Note: CAsE SEnSitiVE)
/system/etc/e2fsck -fpDC0 /dev/block/mmcblk0p2 (Note: CAsE SEnSitiVE) <- You now have ext4
7. You can check that it's truly ext4 by:
parted /dev/block/mmcblk0
print (It should now read that you have a FAT32 and an ext4 partition.)
quit
You're all done! Now you have a 1GB ext4 partition for all your data and apps. If you know what you're doing, these same steps can be modified so that you have two ext4 partitions if you'd like. You can also alter the size of your ext4 partition to something smaller if you don't have that many apps to install or have a smaller SDcard (512MB should be sufficient in most cases, 1GB is slightly overkill IMO)
i will try with my HD2. I need more space to install app on sd not on phone. Thanks so much
Hi, I follow your instruction but when I get a "Permision deined" error when I type in the following commond
/system/etc/tune2fs -j /dev/block/mmcblk0p2
Can you please help?
Many many thanks!!
justj said:
Hi, I follow your instruction but when I get a "Permision deined" error when I type in the following commond
/system/etc/tune2fs -j /dev/block/mmcblk0p2
Can you please help?
Many many thanks!!
Click to expand...
Click to collapse
Crap. I forgot a step. You have to type
chmod 777 /system/etc/tune2fs
chmod 777 /system/etc/e2fsck
prior to using those files. That should fix the permission denied error.
I've edited the OP to reflect the changes, thanks for pointing that out.
Thanks man
Thanks Bro I have successfully make ext4 and I am enjoying my new Rom
Using HTC Desire runnymede 5.0
Amazing. I will keep it for future reference, although I partitioned my SD with CWM recovery and Gparted.
What kind of partition is made when using CWM? I made a 1GB partition on my card that way, and it works great. But I've heard good things about having it as ext4. How does this guide reflect the fact that I already have an SD-EXT on my card that's not necessarily ext4?
Thanks!
please help
please help me i cant get it to work... its same with /system mounted and unmounted...not even one 3rd app is working for me on my win 7 64x when i want to create ext4 this is my last hope. card is brand new 8gb ultra speed its working fine so cant be problem there. it seems like chmod 777 will delete that file..
Code:
C:\Users\OgziR\Desktop\adt-bundle-windows-x86_64-20130522\sdk\platform-tools>adb
push ext4 /system/etc/
push: ext4/tune2fs -> /system/etc/tune2fs
push: ext4/e2fsck -> /system/etc/e2fsck
2 files pushed. 0 files skipped.
1573 KB/s (603400 bytes in 0.374s)
C:\Users\OgziR\Desktop\adt-bundle-windows-x86_64-20130522\sdk\platform-tools>adb
shell
~ # /system/etc/tune2fs -j /dev/block/mmcblk0p2
/system/etc/tune2fs -j /dev/block/mmcblk0p2
/sbin/sh: /system/etc/tune2fs: Permission denied
~ # chmod 777 /system/etc/tune2fs
chmod 777 /system/etc/tune2fs
~ # /system/etc/tune2fs -j /dev/block/mmcblk0p2
/system/etc/tune2fs -j /dev/block/mmcblk0p2
/sbin/sh: /system/etc/tune2fs: not found
~ #
Hye... I have 2 question...
My phone is a HTC HD2 running an NexusHD2.ICS.CM9.HWA.V2.3 ROM... The cmd prompt cant seem so fine my device. Do have any advice on this???
Secondly, what do i do with the ext4.zip file??? I mean, do it extract it, or put in same folder with ADB??
Btw, i am Super Noob on this, so i apologize if my question offends anyone... 1000 apologizes...
OK, first of all, do you have adb installed correctly? If cmd prompt can't find your device that is the most likely problem.
As for what to do with ext4.zip, you need to extract it to your adb folder.
Sent from my Vivid 4G using xda app-developers app
>>> Please note that Vashiru reworked this guide for reliability and alternate values, so I recommend you check his various posts in this thread starting with this one. <<<
Click to expand...
Click to collapse
THE PROBLEM
As many of us have noticed, it is fairly easy to get an "Out of space" message when installing apps on our phones because, for some weird reason, Oppo decided that the storage part of the device should linger in the dark ages, when /userdata and /sdcard were separate partitions and you only had 2GB of data storage, even if your phone was a 32GB model.
Now, imagine that you are running KitKat and would like to try ART. This may be a bad idea as, if your data partition is more than 30% full, you will find that while converting your apps to this new format, Android will run out of space.
At OppoForums, a few bright people started looking into the issue and, of course, there is a way to improve the situation.
WARNING!
If you follow the steps below correctly, you should not run in any trouble. If you do not, however, you may end up spending much more time fixing your phone.
FIRST, THE THANKS SECTION
Anders tinkered with his device’s partition table until he got to where he had grown the /userdata partition to something useable. Yes, it’s some people’s definition of “play”
Jousa11 is the first person trying to put a guide together explaining the steps to reproduce Anders’ work. WARNING: I did no get to see said guide as Jousa quickly deleted it due to the risks involved. So, take that in account!
Rockman for providing the last resort rescue tools in case you brick your phone
Lucky for providing the WiFi fix
Please let me know if you are not on this list and I forgot to give you credit!
YOU WILL NEED
The hardware:
An Oppo Find5 phone(!)
A computer (Windows/Linux/Mac) with adb installed and working
A USB cable
On your computer:
adb
[Optional] fastboot
On your phone (SDCard):
parted + mke2fs + tune2fs
mmcblk0p21_persist_ext4.img
openrecovery-twrp-2.6.3.0-find5-TP-patch.img
[Optional] gdisk
You will use parted to work on your partition table; mke2fs and tune2fs to create ext4 filesystems on some of these partitions (parted does not know how to create ext4 partitions)
mmcblk0p21_persist_ext4.img is an image that you need to restore your /persist partition and avoid issues such as non-working WiFi.
openrecovery-twrp-2.6.3.0-find5-TP-patch.img is a patched recovery image. I know: you already have a recovery image if you are going through these steps. However, we are going to wipe it so you want to install this guy before rebooting. Note that if you forget, you can always flash it later using fastboot.
On your computer:
adb to access your phone recovery, push files to SDCard, reboot...
[Optional] fastboot. You will only need fastboot if you mess up your recovery partition.
WHAT IF SOMETHING GOES AWFULLY WRONG?
You may “brick” your phone. Apparently it’s near impossible to hard brick your Find5, though. See below.
First, Anders recommends making a backup of your partition table. I didn’t because I felt that if I messed something up, it would be a partitions’ content rather than the partition table but that’s not the wisest approach.
Furthermore, if you are really worried about what stilly error your fat fingers will cause (I know I should be!) you can also backup your partitions.
Backing up your partition table:
On your phone:
Code:
gdisk -b /sdcard/gpt.bin /dev/block/mmcblk0
Backing up a single partition:
On your phone:
Code:
dd if=/dev/block/mmcblk0p<partition id> of=/sdcard/backup-<partition id>.bin
On your computer:
Code:
adb pull /sdcard/gpt.bin
adb pull /sdcard/backup-<partition id>.bin
LAST RESORT
OK. So, you've bricked your phone. Now what?
First, you will need Windows. So if you're on a Mac or Linux and have no access to a Windows machine/VM, er..don't brick your phone.
- Download drivers and tools
- Download and follow the instructions
READY ? LET'S GET STARTED
>>>>>>>>>>>> First, Download The Files <<<<<<<<<<<<
Then...
On your computer:
UPDATE As dixxa pointed out, mke2fs and tune2fs may already be present on your device. It was not the case for me but you should check first; it seems like a good idea to use existing binaries.
Code:
adb reboot recovery
adb push parted /sbin
adb push mke2fs /sbin
adb push tune2fs /sbin
On your phone:
Code:
chmod 755 /sbin/parted /sbin/mke2fs /sbin/tune2fs
umount /cache
umount /sdcard
umount /emmc
umount /data
parted /dev/block/mmcblk0
You are now in the parted shell.
CAREFUL! Do not delete any partition below 20 or you will enter "Big Oops" territory. I recommend typing carefully and, yes, staying away from copy/paste operations that may swallow a character like, say, the '2' in '20'
Note that the size value I am using here is '4GB' for /userdata (rather than 2GB). I guess you could make /userdata bigger than 4GB, in which case you would have to recompute all the offsets in the commands below(!)
Code:
# rm sdcard
rm 29
# 28 thru 23 are reserved
rm 28
rm 27
rm 26
rm 25
# rm recovery
rm 24
# rm misc
rm 23
# rm cache
rm 22
# rm persist
rm 21
# rm data/emmc
rm 20
# now, re-create partitions but data is bigger
mkpart primary 1325 5421
name 20 userdata
mkpart primary 5421 5430
name 21 persist
mkpart primary 5430 5967
name 22 cache
mkpart primary 5967 5968
name 23 misc
mkpart primary 5968 5979
name 24 recovery
mkpart primary 5979 6012
name 25 reserve1
mkpart primary 6012 6019
name 26 reserve2
mkpart primary 6019 6028
name 27 reserve3
mkpart primary 6028 6062
name 28 reserve4
mkpart primary 6062MB 100%
name 29 sdcard
# exit parted shell
q
Let's create a file system on the partitions that require one. Note that I am formatting the SDCard using VFAT as, yes, EXT4 is a better FS, but it is also incompatible with Oppo's ROM and some apps may not require the proper permissions etc.
Code:
# Notes:
# -m 0: no reserved blocks
# -c 0: no max mount count
# -C -1: no mount count
# -i -1: max_int interval between checks
mke2fs -t ext4 -m 0 -L userdata /dev/block/mmcblk0p20
tune2fs -c 0 -i -1 -C -1 /dev/block/mmcblk0p20
mke2fs -t ext4 -m 0 -L persist /dev/block/mmcblk0p21
tune2fs -c 0 -i -1 -C -1 /dev/block/mmcblk0p21
mke2fs -t ext4 -m 0 -L cache /dev/block/mmcblk0p22
tune2fs -c 0 -i -1 -C -1 /dev/block/mmcblk0p22
# Hey look it’s an ext4 SDCard!
mke2fs -t ext4 -m 0 -L sdcard /dev/block/mmcblk0p29
tune2fs -c 0 -i -1 -C -1 /dev/block/mmcblk0p29
# Actually to avoid errors like unable to write to root of sdcard:
mkdosfs -n sdcard -F 32 /dev/block/mmcblk0p29
mount -t vfat /dev/block/mmcblk0p29 /sdcard
At this point, we have clobbered the /persist partition and this could cause issues as mentioned earlier. Let's restore it.
Code:
# Restore /persist partition
mount -t ext4 /dev/block/mmcblk0p29 /sdcard
# On computer
adb push mmcblk0p21_persist_ext4.img /sdcard/
# On phone
dd if=mmcblk0p21_persist_ext4.img of=/dev/block/mmcblk0p21
IMPORTANT! Flash your recovery partition now. If you wait until after rebooting, you will need to use fastboot instead.
Code:
# Recovery partition: on computer
adb push openrecovery-twrp-2.6.3.0-find5-TP-patch.img /sdcard/
# On phone
dd if=openrecovery-twrp-2.6.3.0-find5-TP-patch.img of=/dev/block/mmcblk0p24
Admire your work
Code:
parted /dev/block/mmcblk0 print
Reboot into your new recovery and install your favorite ROM
FAQ
Q: Is this dangerous?
A: Yes. Yes, it is.
Q: Any tip?
A: Yes. Follow these instructions carefully and if something wrong happens, unless you know what you are doing, leave your device alone and come here to ask for help.
Q: Can I hold you responsible for any damage to my phone/etc?
A: As usual, the answer is 'No'
Q: I found an error in your write-up!
A: Please let me know immediately.
-Chris.
You should probably use the latest TWRP 2.6.3.1 found here: http://techerrata.com/file/twrp2/find5/openrecovery-twrp-2.6.3.1-find5.img
Looks good to me. Just be very carefully doing this.
Sent from my Find 5 using xda app-developers app
gdisk -b /sdcard/gpt.bin /dev/block/mmcblk0
those commands need to be typed in recovery even that one ?
Yes although I imagine this particular command should also work when booting system.
Sent from my Find 5 using Tapatalk
This thread is fine the only problem here is with those 2 binaries: mke2fs and tune2fs
You don't need to push them or chmod them since they are already in the recovery
Except that that thread is perfect.
Since we're at toying with partition, can't we merge the partitions in some way ?
Just wondering is there any way to build a script to do this in an automated way thus avoiding user errors and typos?
There is a thread on the oppo forums
http://www.oppoforums.com/threads/guide-resizing-internal-storage-on-find-5-32gb.8361/
Hello everyone,
is the guide for the 32 or 16 gb model?
I have 16 gb Oppo find 5.
Thanks.
PS: what "on your phone" is supposed to mean"?
Click to expand...
Click to collapse
If you don't know what does that mean don't do it you'll screw your phone.
hi
Please would you make something like this for oppo find 7a x9006?
thanks
Anyone willing to recompute all the offsets dor just one 16gb partition?
Scribed henceforth from thy G pad.
Hi all, I am trying to do this mod and I am half way through it with a problem
I am stuck on the new file system, I cannot use mke2fs or tune2fs, i get
Code:
mke2fs: not found
like it doesn't even exist, but it does I can see it. I get the same error for tune2fs. but parted and gdisk work fine.
Yes I did push them and chmod 755 them.. and I have tried running it from the /sbin directory.
Help!
Hello!
I'm getting the same error over and over again creating /dev/block/mmcblk0p21 to /dev/block/mmcblk0p22:
tune2fs -c 0 -i -1 -C -1 /dev/block/mmcblk0p21
"Bad magic number in super-block while trying to open /dev/block/mmcblk0p21"
"Couldn't find valid filesystem superblock"
So i can't create a file system on the created partitions. I have been looking everywhere for an answer. Somebody have an idea?
U should just wait. Andrew dodd found a way to make find7a have unified partition and he claims he can make it work on find5 as well. Let's give him a bit to figure it out tho.
Scribed henceforth from thy G pad.
Gdisk not working...
Ok guys sort of a noob here... Firstly, totally appreciate what you guys are doing here... I wants it bad, thass why i'm here.
So far... I have i have done...
"adb reboot recovery"
"adb push gdisk /sbin"
I figured that's how you are supposed to install it ... hope i'm not wrong, but i guess it pushed through fine
But after rebooting to system in TWRP , i opened terminal emulator and when i use the command
"gdisk -b /sdcard/gpt.bin /dev/block/mmcblk0"
I get ...
"/system/bin/sh: gdisk: not found"
now i'm too scared to proceed without backing up the partition tables... so please help...
edit - FYI , i'm running the last build of Asylum Carbon... should i just go back to latest oopo stable stock rom and then root my device again and then try all this again... would that help... ???
Directly from Andrew Dodds g+ " IT HAS BEGUN.
The first phase of Find 7a/7s LVM testing is here.* See linked post for details.* (Sorry to disappoint, but the first phase is "make sure we don't break existing configurations")
Once this phase is complete, the remaining list is:
Fix up the remaining TWRP issues (make RECOVERY_SDCARD_ON_DATA runtime instead of compile-time)
Make user-friendly conversion processes
Once things are solid on Find 7, I'll work on Find 5 and N1."
Stay thirsty my friends. Good things ahead
Sent from my A0001 using Tapatalk
Does this work for the 16gb model?
Can someone help please?
I'm trying to do this, but after enter in parted [parted /dev/block/mmcblk0] when i try to do "rm 29", i get "can't remove 29: no such file or directory
I'm doing the "on your phone" commands in TWRP command line., is that correct?
I'm running stable colorOS 1.0.9i
Finally I finish the process.
My notes:
Goal:
Keep my current system intact (stable colorOS 1.0.9i , because i have no patience to format, install a new ROM and reinstall/recofigure everything
So I backup everything on phone with TWRP and I push sdcard content (wich include the system backup i made) with ADB
1 - If I push mke2fs and tune2fs IT WILL NOT WORK. I flash the last find 5 recovery (openrecovery-twrp-2.8.1.0-find5.img) and I dont push or chmod anyting, parted, mke2fs, tune2fs are all already in the recover and that's the only way I could run mke2fs and tune2fs
edit: 1.5 - The phone commands had to be enter via ADB shell. In TWRP command line, after you enter in parted it will not accept commands.
2 - To "rm 29", i had to "umount /dev/block/mmcblk0", otherwise "rm 29" fail due to partition in use
3 - after this instruction:
mount -t vfat /dev/block/mmcblk0p29 /sdcard
(the last one on the 4 block of code)
We have this:
# Restore /persist partition
mount -t ext4 /dev/block/mmcblk0p29 /sdcard
This instruction was the only one that give me a error, so I move to the next ones.
The error was that the partition was busy, what makes senses because in the last instruction we mount the same partition on the same folder but with different file system!!??
So I move to the next instruction. I have no idea if it's a instructions mistake but it looks like, because it says "# Restore /persist partition" but the command has nothing to do with /persist
4 - FINISH
5 - Reboot in recovery. Push sdcard backup to /sdcard. restore system backup with TWRP restore
Voila, my phone exactly as before but with 3,76GB for APPS. Finally!!! The "running out of space" message on a flagship quad-core 2GB RAM phone!!!!!!?????? Was driving me CRAZYYYYY
Thanks Fickx for the up to date information, I just did my re-partition successfully, here's what I did:
- Use Rashr update the recovery to twrp-2.8.1.0
- reboot into recovery
- connect to PC (Make sure adb works, "adb devices")
- on PC:
> adb shell
> umount /cache
> umount /sdcard
> umount /emmc
> umount /data
> umount /dev/block/mmcblk0p29
> parted /dev/block/mmcblk0
> rm 29
>...
> rm 20
> mkpart primary 1325 5421
> name 20 userdata
> ...
> name 29 sdcard
> q
> mke2fs ...
> ...
> mount -t -vfat /dev/block/mmcblk0p29 /sdcard
Open another PC command terminal
> adb push mmcblk0p21_persist_ext4.img /sdcard/
> adb push openrecovery-twrp-2.8.1.0-find5.img /sdcard/
Back to original terminal in "adb shell".
> dd if=/sdcard/mmcblk0p21_persist_ext4.img of=/dev/block/mmcblk0p21
> dd if=/sdcard/openrecovery-twrp-2.8.1.0-find5.img of=/dev/block/mmcblk0p24
> exit
> adb reboot recovery
Flash the rom.
hey guys,
i have a huge problem with my Iconia A200. (I know its a a500 forum, but I think they are nearly the same..)
When I enter TWRP, I am not able to mount or wipe /data.. It says "Unable to mount /data".
I cant even install a Custom or Stock Rom (because of blabla /data).
Then I tried to follow this guide:
http://forum.xda-developers.com/showthread.php?t=1798652&page=3
The problem is point 2:
2) /Data would not mount - I have no idea how this got screwed up, but the solution was:
* Connect the tablet to the PC in RECOVERY. At this point, ADB should work. If not, check the drivers on the PC - I had to manually specify the Acer ADB Composite driver.
* Open a Command prompt window
* Start ADB shell by typing:
ADB SHELL
* Now execute the following:
mke2fs -j -b 4096 /dev/block/mmcblk0p8
tune2fs -O extents,uninit_bg,dir_index -C 1 /dev/block/mmcblk0p8
e2fsck -fy /dev/block/mmcblk0p8
After this is done your file system on /data will be fixed. (solution posted by spoupard on XDA-Developers.com)
When I enter mke2fs -j -b 4096 /dev/block/mmcblk0p8 after "adb shell" nothing more happens.
It only says mke2fs 1.41.0 (DATE..2010 or something) and then.. Nothing more.
Can someone help me to fix the /data problem?
Ah and I dont have a ROM installed yet, hard reset is broken, too..
Q&A for [HACK] Grow your data partition
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for [HACK] Grow your data partition. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
killerskincanoe said:
Directly from Andrew Dodds g+ " IT HAS BEGUN.
The first phase of Find 7a/7s LVM testing is here.* See linked post for details.* (Sorry to disappoint, but the first phase is "make sure we don't break existing configurations")
Once this phase is complete, the remaining list is:
Fix up the remaining TWRP issues (make RECOVERY_SDCARD_ON_DATA runtime instead of compile-time)
Make user-friendly conversion processes
Once things are solid on Find 7, I'll work on Find 5 and N1."
Stay thirsty my friends. Good things ahead
Sent from my A0001 using Tapatalk
Click to expand...
Click to collapse
Any update ?
abuthabet87 said:
Any update ?
Click to expand...
Click to collapse
I'm working on it, got a base for the find5 on the omni gerrit already. Though far from usable
Sent from my One X+
2 questions
Is this Hack [suficient] safe, or should I wait for LVM?
If i do a full backup of my current system (colorOS 1.0.9i Stable) and after the hack, restore the ROM, will my phone be exactly the same than before but with 4GB for apps?
Thanks for the great work
LVM needs ALOT of work right now :/
I'm trying to do this, but after enter in parted [parted /dev/block/mmcblk0] when i try to do "rm 29", i get "can't remove 29: no such file or directory
I'm doing the "on your phone" commands in TWRP command line., is that correct?
I'm running stable colorOS 1.0.9i
Guys, After I exit parted shell, I can't execute mke2fs/tune2fs commands! I get:
/sbin/sh: mke2fs: not found
though I can find them (mke2fs and tune2fs) inside /sbin/ after I cd into it!
How can I solve this ?
Edit:
Solved ... I just rebooted into recovery again.
I did it It works hehehe
Thank you very much for this amazing instructions.
I had some difficulties while executing some of the instructions, but I did some search and tried unplugging then plugging the cable or rebooting into recovery again when the shell was giving me a hard time, and everything is back as it was except now I have 4GB internal storage !!
Does this have to be done while the phone is running ColorOS? I started the procedure on my 16GB phone, running CM11, but didn't get too far.
There is no /sbin. Found tune2fs and mke2fs in /system/bin. No parted there.
From PC over USB, copied parted to Download directory.
On phone, opened a Terminal, then 'su root'.
Remounted /system/bin rw: 'mount -o rw,remount /dev/block/platform/msm_sdcc.1/by-name/system /system'
Copied parted from Download to system/bin.
chmod 755 /system/bin/parted
Most of the umount commands fail.
Started 'parted /dev/block/mmcblk0'
Fails on first 'rm 29' because it is not unmounted.
I gave up there.
Interesting, automated repartioning:
www <dot> youtube <dot> com / watch?v=2CoTIojZGlI
Shame it doesn't have a 4GB option.
@Redfoox (in dev thread), did you push mke2fs and tune2fs at the beginning of the procedure or did you use the ones already included in TWRP?
I got this error?
Code:
/sbin # mke2fs -t ext4 -m 0 -L userdata /dev/block/mmcblk0p20
/sbin/sh: mke2fs: not found
The command also does not work in TWRP!
Anyone any idea what I should do now?
---------- Post added at 02:40 PM ---------- Previous post was at 02:36 PM ----------
Vashiru said:
@Redfoox (in dev thread), did you push mke2fs and tune2fs at the beginning of the procedure or did you use the ones already included in TWRP?
Click to expand...
Click to collapse
I did push the mke2fs and tune2fs at the beginning. Probably shouldn't have done that?
I have to wait each post for 4 minutes to post a new one
I've tried doing that during my second attempt, but got stuck at exactly the same point.
The fact that it shows mke2fs: not found tells me that you have both pushed it and CHModded it.
Push the files again, this time don't CHMod them and try it from the TWRP Terminal Emulator (from ADB shell just gives you permission denied but I didn't try it from TWRP that time).
If that doesn't work try CHModding them from TWRP. If that also doesn't work I'm out of a clue. All you could do at that point is use the last resort method (saved my device 2 times) and try the procedure again without pushing the files first.
Tried it and it gives the same errors. Cannot even chmod it through the terminal emulator.
I will go for the last resort method than
Too bad. Alright, feel free to ask questions if you run into trouble when you try again.
It worked i have 4GB now!
The only thing now is that my wifi does not work and I did do the following:
Code:
# Restore /persist partition
mount -t ext4 /dev/block/mmcblk0p29 /sdcard
# On computer
adb push mmcblk0p21_persist_ext4.img /sdcard/
# On phone
dd if=mmcblk0p21_persist_ext4.img of=/dev/block/mmcblk0p21
output of terminal:
Code:
/sdcard # dd if=mmcblk0p21_persist_ext4.img of=/dev/block/mmcblk0p21
16384+0 records in
16384+0 records out
8388608 bytes (8.0MB) copied, 3.260498 seconds, 2.5MB/s
Any idea how to restore this? I even redid this step without succes.
---------- Post added at 07:21 PM ---------- Previous post was at 06:27 PM ----------
Got it working now. I had tot install modem 4.2.
Nice, enjoy the 4 GB!
Please help guys this is turning out to be a really frustrating experience...T___T
How are you guys even pulling this off... T___T
My adb works when the phone is booted but after "adb reboot recovery" and once in TWRP it cant see the device... and hence i cant proceed with the commands in Adb shell when the phone is connected and in twrp. i am running Liquidsmooth rom but i went back to the original rom to try this.
I'm able to execute
" chmod 755 /sbin/parted /sbin/mke2fs /sbin/tune2fs
umount /cache
umount /sdcard"
But not these ...
"umount /emmc
umount /data"
It says file or Directory not found.
then when i enter parted with the next command "parted /dev/block/mmcblk0"
I enter into parted, but cant see any of the following
"# rm sdcard
rm 29
# 28 thru 23 are reserved
rm 28
rm 27
rm 26
rm 25
# rm recovery
rm 24
# rm misc
rm 23
# rm cache
rm 22
# rm persist
rm 21
# rm data/emmc
rm 20
# now, re-create partitions but data is bigger
mkpart primary 1325 5421
name 20 userdata
mkpart primary 5421 5430
name 21 persist
mkpart primary 5430 5967
name 22 cache
mkpart primary 5967 5968
name 23 misc
mkpart primary 5968 5979
name 24 recovery
mkpart primary 5979 6012
name 25 reserve1
mkpart primary 6012 6019
name 26 reserve2
mkpart primary 6019 6028
name 27 reserve3
mkpart primary 6028 6062
name 28 reserve4
mkpart primary 6062MB 100%
name 29 sdcard
# exit parted shell
q"
Now i'm totally clueless on how to proceed further... Would appreciate if you guys can shed a bit more clarity... This is really turning out to be a frustrating experience. Please guys...
Going back to Liquidsmooth to use my phone ... will again reinstall original os tomorrow and try again. :crying:
OK, so I got TWRP running sweet and now following the improved descriptions in main thread post #34.
Got stuck here, all before has been ok:
mke2fs -t ext4 -m 0 -L persist /dev/block/mmcblk0p21
Message back is:
Could not stat /dev/block/mmcblk0p21 --- no such file or directory
The device apparently does not exist; did you specify it correctly?
Now what?
EDIT - think I have it sorted. I didn't scroll down enough in the post #34 windows and missed some 'parted' commands!
EDIT - 'adb shell' had quit, and it wouldn't connect again. Tried to reboot TWRP to recovery, but it didn't recover, now stuck at Oppo text logo, can't connect by adb, doesn't respond to power button. Bricked.
EDIT - was able to access the phone by fastboot only, not adb. Flashed TWRP recovery again, it rebooted and took quite a while, now it is stuck at the cyanogenmod 12 boot up spinning arrow for 10+ minutes, maybe it will recover eventually. If not, I'll try to reflash CM12 too.
Hello
Today was the third try to get this thing working ^^
But somehow i cant get past the first command.
Every time i try to unmount things like /cache or /dev umount only returns "invalid argument.
I never pushed the files from the zip. TWRP 2.8.3.0 is used.
I tried to attach a screenshot to help, but im too new to do that -.-
Thanks in advance