[Q] How to fasten the WiFi?! - Eee Pad Transformer General

Hi dudes, im new...and old^^
does anyone know how to fasten the wifi ?
Hoped the rooted pad + revolver rom worx faster with wifi...
But nothin noticeable faster with wifi...
THX 4 answers!!!
BEst regards, Oliver

what are you talking about?

...the wireless internet connection from the eee pad is slow as hell!

You keep using that word, 'fasten'. I don't think it means what you think it means.

ok well in order to give you and advice or help or tips on how to speed up your throughput over your wifi connection, we're gonna need to know exactly how your network is setup. router, other wireless and wired clients that might be on the network, wireless configuration and settings on both the router and the other devices, etc,etc,etc. so get all that info, come back post it up and i'll see if theres any room for improvement.

...in the deed - fasten was wrong^^ - faster!
Sry. my english isn´t that good.
AND - my known configurations - using cable @ 20mbit with an D-Link DIR-645 / 802.11n.
Connected with cable to my pc...wireless of course two mobile phones, and a laptop above
(mostly disconnected) - in the hole appartment we got full shown wifi receiving.
Dont manage any special settings for the router, using auto setup with WPA2...
The EEE Pad (only WiFI) is rootet and got the revolver rom on it.
Im not a specialist in configuing networks u see^^
I hope thats of course enough info?!
THX for help - regards, Oliver

Is it even possible..?
Mine is pretty fast though.
Decend for me.

The problem with the TF101 only uses the 2.4 Ghz band and not the faster 5 Ghz.You can setup the router to only have the 101 on the 2.4 band and everything else use the 5Ghz for devices that can use that.

Is it just me who is having Wi-Fi problems?
I use the wireless internet on my PC. It connects fine, good reception.
But my tf101 has trouble connecting... it sometimes connects, but then it loses connection randomly. Sometimes the wireless network isn't even under the listed available networks, it just disappears. But then, nek minit, it reappears, and attempts to reconnecting. It sometimes fails and sometimes manages to reconnect for either a brief moment or a long time(rare).
Anyone else ?

Related

WiFi?

Hi, i recently bought and upgraded a 02 XDA Mini S to WM6 and the wifi seems bad like i have to go right next to the wireless point to get a good signal and even then its not at full bar can any1 help me with this or is it just the wifi is rubbish on the wizard?
thanks,
Kurt
Did you go to start-->settings-->connections tab-->wireless LAN-->power mode tab and set it on best performance? That should give you some more room to work with.
yep still is really bad though about 10 meters and 2 walls away from the router an i couldnt get a signal.
At "10 meters and 2 walls away from the router" I also get no connection -where my Wifi enabled laptop works fine at the same time. Seems like the Wifi on the HTC device is rather weak and operates from a small distance only. Anyways I've learned to live with it.
oh rite well annoying though considering my dell axim x51 can get a very good signal like 30 meters from the access point. is there anyway i can up the power on my wizard? ive got wireless G enabled aswell.
Ya, I have a 7db antennae on my router and I still seem to need to be inside of 20 or so feet, and no walls for my wizard to find the network. I think it's just a weak card.
I also noticed that.
Yes I also noticed that. I have a wifi hotspot subscription and with my old WM5 ROM i can connect and surf without any problem, however when useing any WM6 ROM i just connect poorly and the connection breaks everytime.
Even in my wireless home router i had turn on the name broadcast (enabling WEP of course) in order to connect properly at the first try.
Ive noted this with every WM6 Rom out there and since my device is a G4 i cant upgrade the radio rom. so... well i suffer from this issue also.

Wifi sucks on touch HD

When I first bought the touch HD I was thinking how good it would be to have this phone while having wifi with the lack of 3g for tmobile in the us, but it turns out that the wifi acutally suck! I have a iPod touch 2g And the wifi works great with blazing speed. I can't seem to detect my wifi at home mean while I'm connected on my wifi with my iPod. I been very disappoint with this phone for simple fact that this phone recieves wifi poorly. Anyone can help me out with this problem would be much appreciated because despite the wifi problem I love the phone cause the 3.8 screen is so damn sexual lol.
I've no such issues!
Try to set wifi power options to performance. Also, Enabling G Mode (with SKTools is one of the ways) helps improve speed.
Thanks for the info but it might be the lack of range of my router cause I have been on my wifi with the phone before but I get disconnected frequently and most the time it doesn't even show up or detect it but I don't have that problem with the iPod. With iPod I seem to get wifi everywhere. I'm starting to believe the iPod is better might sell it and get a iPhone or maybe a hero but don't know if I'm willing to spend 600+ on another phone
Next time put [rant] on the title
My wifi connects well to open, WEP, and WPA connections. I tried numerous access points (at least 30), even 802.11n APs in mixed g mode. It even connects to Apple Airport (802.11g). The connection is stable both on power saving and best performance, but I think I get much better speeds on average with best performance.
Its wifi range is much better than my little HP 613 smartphone, but again worse than my notebook. I get 54Mbit connection with signal quality of about 50% at 10 meters through a wall and then it automatically finds another channel on another AP. It roams (handover) APs better than some Lenovo r61 laptops around!
But I am not satisfied with its speed (even on best performance) - it finishes copying a 700MB file on a 54 Mbit connection in 30-40 minutes using total commander and saving on storage card. That means average speed is around 300-400KB/s - laptop does the same (same AP, same file, same network settings) at 1.6-1.8 MB/s in around 7 minutes.
I also noticed that saving on storage card is slighty faster than into the main memory...
I can't seem to detect my wifi at home mean while I'm connected on my wifi with my iPod.
Click to expand...
Click to collapse
Hmm, are you sure that you don't compare two different situations ? Did you also try connecting to Wifi with your iPod while already being connected with your Blackstone ?
My personal experience shows me that the Touch HD seems to have a better radio than the iPhone 3G. Have you upgraded to the latest Blackstone stock ROM and radio available on the HTC website or XDA Devs ? Whether or not the radio also affects Wifi unfortunately I don't know.
Moreover, use WifiMonster to monitor the strength of the signal, it'll help you discover the best spots for using Wifi. I even receive Wifi signals from the neighbors' houses in my own house (not speaking about appartments), of course that always depends on the room !
BTW I'm pretty sure that a Hero won't solve your problem, it's the same old hardware specs as on the Blackstone.
The Wifi on my device works perfectly and i have had no issues at all with signal or quality. I have had more problems with my ipod than the HTC, are you sure its not the WIFI AP you are trying to connect to? Also are you using stock rom or custom?
I'm using the Energy ROM. I'm assume its my wifi signal its very weak and my touch hd cant seem to detect it. With my ipod i shows up and i can connect to it...will updating the radio make a difference?
I came across a startling discovery the other day regarding the Touch HD wifi. I was also having issues at home with weak wifi signal. I didn’t seem to have this problem with public access hot spots.
I have a Logitech wireless mouse connected to my computer and very rarely turn that computer off. I found that when my computer was off I would get a rock solid connection to my home wifi, but when the computer was on it would drop in and out. I narrowed it down to the wireless mouse was interfering with the Touch HD wifi connection.
I tried all different channels on my router, but as long as the Logitech mouse was plugged it I would get wifi dropouts. But as soon as I unplugged the mouse and the radio dongle, I wouldn’t have any problems with the Touch HD wifi.
I can’t comment if this is your issue, but something might be interfering in the 2.4Ghz with wifi.
Guys,
Sometimes even cordless phones, microwaves, etc will interfere with the connection.
Cheers.
As Poison Wolf correctly pointed out, other household items can interfere with the wireless frequency. Try changing the channel that's being used to transmit from your box (This will involve changing some settings on your wireless router so do some research before you fiddle around with it) I have had to do this before and can confirm it can make a massive difference.
ikovac said:
But I am not satisfied with its speed (even on best performance) - it finishes copying a 700MB file on a 54 Mbit connection in 30-40 minutes using total commander and saving on storage card. That means average speed is around 300-400KB/s - laptop does the same (same AP, same file, same network settings) at 1.6-1.8 MB/s in around 7 minutes.
I also noticed that saving on storage card is slighty faster than into the main memory...
Click to expand...
Click to collapse
Everybody has this problem because the card seems not capable of more speed.
But it seems nearly nobody cares.
My old thread about his, no answers:
http://forum.xda-developers.com/showthread.php?t=524272
str0nz0 said:
Everybody has this problem because the card seems not capable of more speed.
But it seems nearly nobody cares.
My old thread about his, no answers:
http://forum.xda-developers.com/showthread.php?t=524272
Click to expand...
Click to collapse
Stron,
Hmm, interesting. The only reasoning I can think of is that perhaps there's a limiting factor in order to reduce the heat or something? I don't see why they would cap the speeds.
Cheers.
What if it is capable of connecting at 54 Mbit, but can actually do only 11 Mbit? Nice trick. I hope it is just a bad idea.

keep loosing wifi connection at home

Not sure if im the only one but every so often my tab does not connect to my home wifi, it does connect to my vibrant via tether no problem. Now i have had this issue a few other times and the only solution i can come up with is to do a factory reset, once i do that i have to set up the connection then im up and running. Does anyone have the same issue? Any suggestions? Dont want to keep reseting the tab just to get a working connection.
Sent from my GT-P1000 using XDA App
Flash your router with dd-wrt up the default signal strength footprint
http://www.dd-wrt.com/site/index
jarez said:
Flash your router with dd-wrt up the default signal strength footprint
http://www.dd-wrt.com/site/index
Click to expand...
Click to collapse
i dont think its anything to do with the router as i am able to connect my Vibrant and my laptop via wifi and no issues, but with my tab sometimes it just sits there trying try to connect
It is probably your router!
My primary router (WRT300N) connects just fine to my laptop, Wii, HD2 (with winmo) Touch pro II with older android port. But refuses to properly connect the Tab, company laptop (IBM), wife's laptop (Packard Bell), Touch pro II with newer Android ports.
It either does not get a IP or with an IP there is no data transfer.
Connected a WAP54g and all connect just fine!
DD-wrt is not supported for this router (V2), so cannot try that.
Is your ssid hidden? i believe froyo was suppose to able to connect to hidden ssids but try disabling that feature. Change it to wep just to check. I am using wpa2; I haven't had any issues.
Bought myself a new router, and now all can connect just fine.
I have the same problem. It just constantly connects and disconnects. Not sure what to do.
Which is the best router ?
Hello,
i own a TP-Link (TL-WR1043ND) Router. My Speed is "only" 65 Mb/s.
Channel 13
11 bgn mixed
Max Tx Rate 300 Mbps
WLAN is lost after xx minutes when the Galaxy Tab goes in standby.
(WLAN Policy: Never)
Which is the best and fastest router for the galaxy tab?
Thx
P.S.: Sorry about my bad english
oberst said:
Hello,
i own a TP-Link (TL-WR1043ND) Router. My Speed is "only" 65 Mb/s.
Channel 13
11 bgn mixed
Max Tx Rate 300 Mbps
WLAN is lost after xx minutes when the Galaxy Tab goes in standby.
(WLAN Policy: Never)
Which is the best and fastest router for the galaxy tab?
Thx
P.S.: Sorry about my bad english
Click to expand...
Click to collapse
Hi,
I have the same problem here, connection gone after a few mins, Wifi shows still connected although I can't access the net.
Contacted Samsung in the UK and they have asked me to return my Tab to them for repair!
Just a shot in the dark, but maybe useful. Some programs like Locale scan WiFi periodically for location info. It drove me nuts isolating the problem when the WiFi tether on my Droid would stop working after 5-10 minutes (random time but constant, because of when in Locale's scan cycle I started the tether). For those that are having problems of being able connect, but then the connection showing on, but seeming dead, that may be the issue. Toggling WiFi off and on reestablishes it, or you could just disable the program doing the scan until you head out to move around again.
oberst said:
Hello,
i own a TP-Link (TL-WR1043ND) Router. My Speed is "only" 65 Mb/s.
Channel 13
11 bgn mixed
Max Tx Rate 300 Mbps
WLAN is lost after xx minutes when the Galaxy Tab goes in standby.
(WLAN Policy: Never)
Which is the best and fastest router for the galaxy tab?
Thx
P.S.: Sorry about my bad english
Click to expand...
Click to collapse
The Tab doesn't support 5Ghz 802.11n or MIMO (the tab only has a single antenna) so 72Mbps is the best you can hope for over the 2.4Ghz channel, which you _might_ get if you stand right beside the router.
In most cases, 65Mbps is the best you can expect from any router with the Galaxy tab. Virtually no mobile devices seem to support the 5Ghz spectrum that the "fast" 300Mbps 802.11n requires.
Also, you'll get faster speeds if you change your setting from "bgn mixed" to "n only" and see if the tab still connects.
I often have difficulty connection to my WLAN at home, often I need to turn wifi off & on again a couple of times and leave it for a minute before it eventually connects. I don't think the WiFi in Android is particularly robust.

WiFi Problems

[Q] Do you have speed problems with Wifi? (N-band)
I have wifi N router and set to N only. I have two laptop both wifi N capable. When I transfer file usung file sharing betwen two laptop I m getting speed abt 3Mb/s but when i transfer file between laptop and SGS I only get speed of 300 Kb/s. SGS support wifi N standerd then why it so. Well I use ES file explorer to access file in my laptop over Wi- Fi.
Sent from my GT-I9000 using XDA App
It's a mobile device, they have lower throughput and probably only 1 antenna (most 802.11n devices have 3). There are a lot of factors, but basically, all that's important is that it supports the 802.11n protocol. Optimisation may lead to faster speed boosts over time though.
Network traffic might also be set to a low priority to help ensure the phone runs reliably for other tasks, but I have no idea why exactly it's slower exactly.
I get 1.5mbs from my nas and wireless n network
Sent from my GT-I9000 using XDA App
i get 19.5mb downlaoding speed
and 4.3mb uplaoding speed
on my wi-fi
my connection 500/500mb
I m talking abt internet speed. I m asking abt file transfer speed betn my SGS and laptop
Sent from my GT-I9000 using XDA App
87 Mbps according to mine
i'll grab a screen shot when i get back home
87 seems too much I only get 25 while copy file on hard drive it self
Sent from my GT-I9000 using XDA App
that's actually low for me, but is better than nothing
my PC down in the cine room gets around 218+ Mbps
I get about 80Mbps laptop <-> network (802.11n 5Ghz), and about 5Mbps SGS <-> network (802.11n 2.4Ghz). Not horrible, but certainly not wonderful. I wish it had a 5Ghz radio too, so I could turn off my 2.4Ghz stuff :-/
[Q] Do you have problems with Wifi? (N-band)
Since my phone is on it's way to the repaircenter I would like to ask you all this Question.
I have problems with my wifi connection. The strange thing is, is that my router is brandnew! b+g+N!!!
The weird part is that it has only problems with the N-band
SO I hooked up another wireless router only with the b+g band and BAM it works.
But that's just messed up to have 2 wireless routers one for laptops and one just for my mobile phone...
So can u try the same thing and give me your comments about this issue?
there was already a topic about this
however one topic we did not touch base on, on the other topic was about the B+G bands
if you read the documentations you'll noticed that for N to work at full speed, it must only listen to N no B no G
when you use Mix mode, N doesn't work well
to use N, you need 2 bands, B + G only needs 1 band
if you enable all 3 B+G+N you only get 1 band for all, so making the N useless
the trick is to update all your old hardware that still runs G or B to N
then you can use pure N, and gain full speed
the SGS phone can run up to 87 Mbps on N
meanwhile computers can go up to 280+ Mbps
AllGamer said:
there was already a topic about this
however one topic we did not touch base on, on the other topic was about the B+G bands
if you read the documentations you'll noticed that for N to work at full speed, it must only listen to N no B no G
when you use Mix mode, N doesn't work well
to use N, you need 2 bands, B + G only needs 1 band
if you enable all 3 B+G+N you only get 1 band for all, so making the N useless
the trick is to update all your old hardware that still runs G or B to N
then you can use pure N, and gain full speed
the SGS phone can run up to 87 Mbps on N
meanwhile computers can go up to 280+ Mbps
Click to expand...
Click to collapse
Okay I will consider it and can give it a try
Can't connect to home WPA2 wifi
Hello!
The problem is that I've been trying to connect to my home wifi like 100 times or more, but I'm still unable to get it working... The wifi it's WPA2 and it has a long sentence password...
Any ideas? Thank you!
arroba3 said:
it has a long sentence password...
Click to expand...
Click to collapse
Maybe you need to shorten your password to try.
[Q] manual wifi fix app?
Hey, like many Android users I'm often having problems with Wifi not connecting to APs. While that can be fixed by restarting Android that takes a lot of time and is more than annoying. There are some apps to solve this issue, they "fix" wifi whenever the screen is turned on (e.g. http://www.appbrain.com/app/wifi-fixer/org.wahtod.wififixer http://www.appbrain.com/app/blade-wifi-fix/com.bladewififix).
That however I don't like either as due to the fixing taking place always wifi connection becoming established takes quite a lot of time. So my question: Is there an app that fixes the wifi connection but does so only manually, e.g. by clicking a widget button?
[Q] Can't connect to Wifi?
I select my Wifi network, I enter in the password, it says connecting, authenticating, connected, remembered, then it says disconnecting, searching, authenticating, and it repeats. The H at the top never disappears, no Wifi icon ever appears, what is the issue exactly?
And yes, I am connecting to a Wireless-G signal.
Don't worry I can't connect to your home network either so it's not a problem with your phone
I suggest you delete the password from the router and try and connect .
If you connect setup again with the password .
jje
arroba3 said:
Hello!
The problem is that I've been trying to connect to my home wifi like 100 times or more, but I'm still unable to get it working... The wifi it's WPA2 and it has a long sentence password...
Any ideas? Thank you!
Click to expand...
Click to collapse
I had the same problem and i manage to fixit with "WIFI STATIC". It's free on Market. Access your router config and add your Galaxy Mac adress, then fill the parameters in WiFi Static. It Works! Never had problems again! Oh, i think you have to put your's computer(s) mac adress too in the router.
is there really no such app? :-(

[Q] Bad WiFi connection. Any solution?

Hello everyone,
yesterday my new POV Mobii tegra arived. Everything works fine, except WiFi. Mostly i cannot connect to any WiFi network. If I get a connection, its very slow and often disconnects. I found other threads where people facing the same problem, but I didn't found a solution.
With my HTC Desire and other WiFi devices i do not have any range problems.
I tested different ROMs (corvus5, modaco r8, stock, buzz07 kernel) with various builds of the WiFi Driver (AR6k).
Has anyone a suggestion what I could do to get a better WiFi connection? Could this be a hardware defect?
Thank you!
Markus
I have this problem too. I have experimenting with different wireless routers. My operator provide me with a Thomson TG784 that has a weak signal. Now am using a Edimax BR-6504n. It is a bit better. But I am thinking of getting a Netgear WN2000RPT
Repeater. If anyone have a Netgear WN2000RPT please let me know if it is any good.
It would be interesting to know what people are using. So feel free to post the name of your wireless routers here!
If you have WiFi connection issues, it is worth checking that you have Bluetooth turned off. WiFi and Bluetooth seem to share the internal aerial and there are wquite a few posts about the two interfering with each other.
today i made more tests on signal quality. if my mobii says "50%", my router says 0% signal quality. if i'm on the same room as my router is, my mobii says 100% and my router says 13-18% signal quality. what the hell?!
I am having some connection issues aswell. It seems to drop connection but when I switch aeroplane mode off then on it seems to wake up the wireless and connect again. Really annoying, wondering if to return it back to the store.
Is there any fix? running 4.3 and no updates yet.
ps. my router is a Billion 7800n

Resources