Disregard Plz :) - Nexus 7 Q&A, Help & Troubleshooting

Hi Guys - I'm stuck and could sure use some help. I was flashing the Kaos Droid V3.7.3 rom (wipe cache, data, factory reset), went through the Aroma installer set up and when I tried to reboot system like usual, I keep ending up back in ClockworkMod Recovery Touch V6.0.1.0. Everytime I try to power off the device to get into "fastboot" mode, it doesn't work. The Nexus 7 toolkit doesn't see the device with trying to reflash factory image.
Seems like if I can just get into fastboot, maybe it'll work.
Or is there some other way to get into Odin and flash firmware? I'm really frustrated and clueless at this point. I've tried all the button combos for fastboot, just not working.
Please help.
Thanks,
Edit: I was able to get into fastboot, let's see what happens after trying to flash the stock image
Edit 2: Shew, I was really panicking there for a few. It's taken me 4+ Hours to figure out, I need Android-SDK to get Adb working and be able to reboot into fastboot and then the toolkit worked from that point.

Related

Fastboot> Recovery dosen't find *.img file on SD card

Hi Guys!
I am trying to root my nexus, unlocked it, installed the right usb drivers, I can see the phone and everything looks right.
Downloaded Superboot for ERE27 with himem enabled and ran this. no problem.
I put the img file on the SD card and when I boot the phone in Fastboot / Recovery it does not find and img files on the SD card.
I tried 2 different cards and also different img files.
When I do this I get first the message no images found than I see the droid with a triangle and a ! in it. - Have to pull the battery.
Ideas anyone?
Thanks
What are you trying to do?
1) you had to unlock the bootloader which enables you to install a new recovery image (which is needed to allow you to install new roms)
2) you had to apply the recovery image Amon RA via a command prompt and a batch file if you use Windows. The phone's USB connection needs to be in development mode and once the batch file executes and successfully finishes you need to reboot the phone.
3) you restart the phone into bootloader mode, use the volume rocker to select the recovery console. If you end up with an andriod and exclamation symbol the Amon RA recovery file was not installed.
4) the new recovery console allows you to clean the SD card. Install roms from the SD card and some other commands. The Roms for the Andriod are in ZIP format and do not need to be unziped. In other words all you need to copy to the SD card is the full ZIP file (approx 75MB) and install that directly from the recovery console.
If your android stays in the booting sequence which is shown as the X with flying little pixels, it's most likely because you did not wipe the device clean first. That item is in the recovery console as well.
Hope this helps. I am just as new to this as you are.
You didn't unzip them did you?
You're trying to root with superboot. Great, but the recovery is not capable of flashing .img files, only .zip updates and roms and such. .img files have to be flashed using fastboot, not recovery, and are flashed from the connected computer.
If you read the superboot instructions from wherever you got the file, you'll see that you have to put the .img in the same directory ON YOUR COMPUTER as fastboot, connect via USB, boot the phone into fastboot, then enter the appropriate command line on the computer to flash the file.
If you've done that, then you are officially DONE with the rooting process.
Also, make damn sure that the superboot version matches the software version on your phone. They're both ERE27, right?
I'm not sure what anosis's post is talking about, but that looks more like the process for installing a custom rom (ie cyanogenmod), than rooting.
To root your phone, you DO NOT need Amon-RA's recovery. You only need that if you want to install custom roms, etc. It wont hurt to have it, as it includes many more functions than the stock recovery, but just to root, you don't need it.
Summary:
If you flashed the superboot.img from your computer via fastboot, your phone is rooted. Done.
You don't need to do anything in the recovery at all for rooting. Only for installing update.zips and custom rom.zips.
Hey, So I have been scouring the forums trying to find some answers about this and you seem to be the closet to my situation. Here is what I did:
So I was running a CM9 Aplha, reverted back to stock 2.3.6 [1ada25375426.signed-soju-ota-189904.1ada2537]) so that I could then apply ICS update [VQ8PQk_V]) which I sucessfully did. This was about a month ago and it was all going well.
Then yesterday I wanted to upgrade to 4.0.4 [hR7QFEtn] so I did and superuser wasn't working properly but then I reinstalled it and got it to work. However I got to the point where everything was working fine EXCEPT for the Google Play store kept on force closing. I spent hours trying last night and could not find a solution.
I tried restoring the previous ICS update that I had and it worked, and then I tried updating again. Also side: My clockwork was on the fritz lately so I was using Zedowmaxs force into clockwork recovery image [fastboot boot recovery3101.img] to force it in sometimes.
Anyway bottom line here is where my REAL ISSUE begins. I decided just to wipe everything and start anew. I factory reset/ wiped properly [cache partition and davliche cache] and then locked my bootloader again. Then tried rebooting. Got stuck on Google screen. Then I unlocked my bootloader again. Tried again, same issue.
So, here is where I am at. Cannot get into recovery from fastboot, takes me back to fastboot. AND, everything is wiped because I locked/unlocked my bootloader. All I can do is adb commands.
I don't know what to do from here and there is a lot of things going on. If you could help that would be great!? What I am going to try next is to flash some recovery on, but I don't know which one/ try to mount a file to my sd card from adb commands.
Daboxk said:
Hey, So I have been scouring the forums trying to find some answers about this and you seem to be the closet to my situation. Here is what I did:
So I was running a CM9 Aplha, reverted back to stock 2.3.6 [1ada25375426.signed-soju-ota-189904.1ada2537]) so that I could then apply ICS update [VQ8PQk_V]) which I sucessfully did. This was about a month ago and it was all going well.
Then yesterday I wanted to upgrade to 4.0.4 [hR7QFEtn] so I did and superuser wasn't working properly but then I reinstalled it and got it to work. However I got to the point where everything was working fine EXCEPT for the Google Play store kept on force closing. I spent hours trying last night and could not find a solution.
I tried restoring the previous ICS update that I had and it worked, and then I tried updating again. Also side: My clockwork was on the fritz lately so I was using Zedowmaxs force into clockwork recovery image [fastboot boot recovery3101.img] to force it in sometimes.
Anyway bottom line here is where my REAL ISSUE begins. I decided just to wipe everything and start anew. I factory reset/ wiped properly [cache partition and davliche cache] and then locked my bootloader again. Then tried rebooting. Got stuck on Google screen. Then I unlocked my bootloader again. Tried again, same issue.
So, here is where I am at. Cannot get into recovery from fastboot, takes me back to fastboot. AND, everything is wiped because I locked/unlocked my bootloader. All I can do is adb commands.
I don't know what to do from here and there is a lot of things going on. If you could help that would be great!? What I am going to try next is to flash some recovery on, but I don't know which one/ try to mount a file to my sd card from adb commands.
Click to expand...
Click to collapse
It looks like the time when you were locking-unlocking the bootloader, you messed up the recovery. Since your phone can get into bootloader menu, I think you can get out of this issue.
Here is what I would do.
1. Unlock the bootloader.
2. flash clockworkmod recovery using fastboot USB.
3. Download recovery-RA-passion-v2.2.1.img, put it in C:\fastboot\
4. Shut down your phone. Then start your Nexus One in Fastboot mode by holding down the Trackball and press the Power button.
5. Connect your phone to your computer. Open a Command Prompt (Start -> All Programs -> Accessories -> Command Prompt), and run the following commands:
cd C:\fastboot
fastboot devices
fastboot flash recovery recovery-RA-passion-v2.2.1.img
now see if you can get into recovery. If you can, just flash a custom rom using install zip from sd card option in the recovery
I didn't read all the replies but fastboot reads from your PC's disk not the sdcard, unless you are running it through shell or something?

Help! Can't boot / cant get into recovery. ..

I was unlocked and rooted and ready to install CM7. I followed all the instructions in the Official Atrix CM7 OP to the T, but when it rebooted, I got stuck on the boot screen with "unlocked" and the red M logo.
I tried to repeat the process several times and ended kind of giving up, factory wiping, and then trying to restore my backup. It appeared to restore successfully, but when I rebooted the phone now wont boot at all. I can't even get it into recovery. No combination or order of button presses or battery pulls / usb plugins will turn it on. I just have a green light like it's charging but nothing is working.
Is it possible to brick your phone even after you have been successfully unlocked and rooted just while you are trying to install CM7?
Please help. I am really desperate here. . .
jimjenkins said:
I was unlocked and rooted and ready to install CM7. I followed all the instructions in the Official Atrix CM7 OP to the T, but when it rebooted, I got stuck on the boot screen with "unlocked" and the red M logo.
I tried to repeat the process several times and ended kind of giving up, factory wiping, and then trying to restore my backup. It appeared to restore successfully, but when I rebooted the phone now wont boot at all. I can't even get it into recovery. No combination or order of button presses or battery pulls / usb plugins will turn it on. I just have a green light like it's charging but nothing is working.
Is it possible to brick your phone even after you have been successfully unlocked and rooted just while you are trying to install CM7?
Please help. I am really desperate here. . .
Click to expand...
Click to collapse
are you using the right recovery? romracer or rom manager!
i am using the tenfar CWM included in the Atrix 4G Automatic Unlock script package. will this not work?
if not, how do I replace it with the right recovery if I cant even get into the phone?
jimjenkins said:
i am using the tenfar CWM included in the Atrix 4G Automatic Unlock script package. will this not work?
if not, how do I replace it with the right recovery if I cant even get into the phone?
Click to expand...
Click to collapse
no, that the old recovery you can use the rom manager if you have , or romracer latest recovery you can find that in the development section, also ther was instruction in the cm7 thread.
you should have left it alone at the M boot screen because it takes about 5-10min to boot after unlock and flash...
everything you do now will have to be through fastboot DO NOT SBF FLASH ANYTHING!!!
Go here to use Fastboot
then download the system.img and boot.img from here
use fastboot to push the boot.img and system.img to your phone
if it gets stuck at the M boot screen let it sit for at least 10min
EDIT: get Romracer recovery from here and push that through to your phone through fastboot
Yeah youre going to have to fastboot wipe recovery then fastboot flash recovery recovery.img
Just download rom racers and rename it..recovery.img
Sent from my GT-I9100 using xda premium
Great. Sorry to be such a noob, but do I decompress the CWM-recovery-atrix5.zip file and push the recovery.img file that's inside it? or push the CWM-recovery-atrix5.zip itself?
Also - every time I am able to get my phone into fastboot mode, it says my battery is too weak to flash anything. I cant seem to get the battery to charge enough to execute any fastboot commands. Any way around this? a powered usb hub?
jimjenkins said:
Great. Sorry to be such a noob, but do I decompress the CWM-recovery-atrix5.zip file and push the recovery.img file that's inside it? or push the CWM-recovery-atrix5.zip itself?
Also - every time I am able to get my phone into fastboot mode, it says my battery is too weak to flash anything. I cant seem to get the battery to charge enough to execute any fastboot commands. Any way around this? a powered usb hub?
Click to expand...
Click to collapse
If you can borrow another Atrix user's battery, or take yours to an AT&T store and see if they can charge it for you.
If you're able to get back into recovery then you can just flash the zip.
If not, you'll need to extract the recovery.img to use it with fastboot, or just download it directly from the OP in romracer's thread. (The left hand link is just the .img, the right hand side is the CWM .zip) Then place it in the same directory as fastboot.
So I can literally flash a different recovery from within another?
jimjenkins said:
So I can literally flash a different recovery from within another?
Click to expand...
Click to collapse
yes but it MUST be working proper first ! its ok to use rom managers cwm but i just prefer the otherone alawys have but n e way there are only 2 that are current (uptodate )
thoughs 2 and with romracers you can. chose
a color that you like not just blue
Sent from my MB860 using xda premium
Its the recovery from tenfar CWM. When I can get it into recovery it seems to be working - with the obvious exception of successfully installing CM7
So I can flash romracer recovery from inside tenfar recovery?
sorry if im being redundant - just dont want to screw it up!
thanks
Just download rom racers cwm. Img, head into fastboot and then fastboot flash recovery recovery-****** (whatever yer recovery image color u chose is)
Sent from my MB860 using Tapatalk
I was able after a full day of leaving the phone plugged in, to charge it up. Then I flashed the rom racer recovery, rebooted into recovery (new version), installed CM7, installed gapps, and voila! A working CM7 Atrix. thank you soo soo much guys.
Can't boot android/recovery
ClearFire said:
you should have left it alone at the M boot screen because it takes about 5-10min to boot after unlock and flash...
everything you do now will have to be through fastboot DO NOT SBF FLASH ANYTHING!!!
Go here to use Fastboot
then download the system.img and boot.img from here
use fastboot to push the boot.img and system.img to your phone
if it gets stuck at the M boot screen let it sit for at least 10min
EDIT: get Romracer recovery from here and push that through to your phone through fastboot
Click to expand...
Click to collapse
Please help!!!
The phone stuck in boot screen and overheat, then restart.
In recovery mode is just black screen.
Phone has Neutrino 2.6GT+ ROM whit Clemsyn's OC kernel 1.6GHz and it has unlocked bootloader.
Can I change the kernel without booting in os or recovery?
This problem show after I was extracting very big zip file and phone overheat.
firecode95 said:
Please help!!!
The phone stuck in boot screen and overheat, then restart.
In recovery mode is just black screen.
Phone has Neutrino 2.6GT+ ROM whit Clemsyn's OC kernel 1.6GHz and it has unlocked bootloader.
Can I change the kernel without booting in os or recovery?
This problem show after I was extracting very big zip file and phone overheat.
Click to expand...
Click to collapse
I am actually having this same problem.
My warranty-replacement (unrelated ear-piece failure) had 2.3.6 pre-installed. Thinking little of it, I unlocked the BL and rooted the phone as usual. After this, I tried to install a couple of the ROM's (Neutrino and Morrisoft) which I was most happy with on my previous Atrix.
After flashing either Neutrino or Morrislee's ROM, the phone hung on the M screen. Waiting approximately 30 minutes with no change, I pulled the battery.
When trying to enter recovery mode, the phone would state, "entering recovery mode..." Then go black.
I ended up using RSDLite and sbf flashing the stock 2.3.6 sbf file back to the phone. Then, I had to re-unlock the bootloader and re-root.
This never happened up to, and including 2.3.4, but did twice last night on these ROM's using 2.3.6, and I've flashed many ROM's and Kernels.
It happened to a lesser extent when trying to flash Clemsyn's stock enhanced kernel to the stock ROM, as I was able to enter recovery mode. Entering recovery mode, it would give errors: mounting cache, mounting system errors, and errors to accessing recovery and recovery log files.
Restore recovery would fail in this state, giving me the above errors as well.
Trying to mount the cache and system in recovery would fail. Trying to format cache and system then mounting these could occur temporarily, but would revert back to unmounted when a restore was attempted.
For these problems I pushed a recovery through fastboot.
Just one word: Fastboot. See if Fastboot works and flash everything from there. Or, as Alterna suggested, flash through RSDLite, but that a little dangerous and can brick your phone if you don't know what you are doing. Hope it helps.
Problem sloved!!!
Alterna said:
My warranty-replacement (unrelated ear-piece failure) had 2.3.6 pre-installed. Thinking little of it, I unlocked the BL and rooted the phone as usual. After this, I tried to install a couple of the ROM's (Neutrino and Morrisoft) which I was most happy with on my previous Atrix.
After flashing either Neutrino or Morrislee's ROM, the phone hung on the M screen. Waiting approximately 30 minutes with no change, I pulled the battery.
When trying to enter recovery mode, the phone would state, "entering recovery mode..." Then go black.
I ended up using RSDLite and sbf flashing the stock 2.3.6 sbf file back to the phone. Then, I had to re-unlock the bootloader and re-root.
This never happened up to, and including 2.3.4, but did twice last night on these ROM's using 2.3.6, and I've flashed many ROM's and Kernels.
It happened to a lesser extent when trying to flash Clemsyn's stock enhanced kernel to the stock ROM, as I was able to enter recovery mode. Entering recovery mode, it would give errors: mounting cache, mounting system errors, and errors to accessing recovery and recovery log files.
Restore recovery would fail in this state, giving me the above errors as well.
Trying to mount the cache and system in recovery would fail. Trying to format cache and system then mounting these could occur temporarily, but would revert back to unmounted when a restore was attempted.
For these problems I pushed a recovery through fastboot.
Click to expand...
Click to collapse
My problem like that and I use automated unlock tool to recover recovery, this recovery show some errors but I successfully flash cwm touch and reinstall Nutrition 2.6GT+

[Q] In Bootloop, Can you Help?

I was having some pretty serious radio issues with cyanogenmod so I attempted to use RSD Lite which had previously worked like a charm to go back to stock rom (using what came pre-bundled with matt's script v. 1.2)
My phone is unlocked at the bootloader
I have it rooted.
I get the original droid boot loop.
I can definitely get it into a status code 3 AP Fastboot, but none of the tools for the script or RSD lite have gotten me past the droid eye bootloop.
I'm presuming a wipe of the cache will do the trick, but either my googling skills are gone or I'm just too tired after 6 hours.... but I'm unable to get any type of recovery flashed.
My first question is if I am in AP Fastboot, who knows how to get a recovery image flashed so I can see if it's just a cache issue of trying to go from cyanogenmod to stock firmware.
My second question is - Does anyone have a link to a guide to "re-lock" my bootloader in case I need to get this to tech support?
Thanks
matthew1429 said:
I was having some pretty serious radio issues with cyanogenmod so I attempted to use RSD Lite which had previously worked like a charm to go back to stock rom (using what came pre-bundled with matt's script v. 1.2)
My phone is unlocked at the bootloader
I have it rooted.
I get the original droid boot loop.
I can definitely get it into a status code 3 AP Fastboot, but none of the tools for the script or RSD lite have gotten me past the droid eye bootloop.
I'm presuming a wipe of the cache will do the trick, but either my googling skills are gone or I'm just too tired after 6 hours.... but I'm unable to get any type of recovery flashed.
My first question is if I am in AP Fastboot, who knows how to get a recovery image flashed so I can see if it's just a cache issue of trying to go from cyanogenmod to stock firmware.
My second question is - Does anyone have a link to a guide to "re-lock" my bootloader in case I need to get this to tech support?
Thanks
Click to expand...
Click to collapse
First off, after you flash the firmware via fastboot, go back into recovery and do a factory reset. Second, you can't relock the bootloader.
thanks for responding. I wish it was this easy - it's been caught in a loop after trying factory again. I think I'd be able to resolve this if there were a way to wipe everything clear and build from scratch
RikRong said:
Second, you can't relock the bootloader.
Click to expand...
Click to collapse
No you cannot relock the bootloader...
Download this http://forum.xda-developers.com/showthread.php?p=40682385 chose option one... once flashed boot into recovery factory reset... boot up device... once booted root... install voodoo protect root install update restore root... install custom recovery if desired... I have boot looped I've been stuck at boot logo I've also been stuck with no data n WiFi this has saved me on more times then I can count on 3 separate devices and his utility n what I described has saved me more times then I can count...
Sent from my XT907 using xda app-developers app
I had some issues with aftermarket recoveries and formatting. I'm not sure if you've had any luck or if this is even helpful but assuming you are in fastboot and have the SDK set up...
Extract the stock sbf/XML and grab the recovery image.
At command line enter: "fastboot flash recovery recovery.img"
Reboot with all three buttons and select recovery.
Do factory reset.
Get back into fastboot
And repeat the command above (with different recovery obviously) to reflash a recovery of your choice.
(The official Philz cwm touch posted recently in development subforum works very well with the new 4.3 ROMs)
Hope that helps...if its too basic, please disregard! Good luck.
Sent from my XT907 using Tapatalk 2

[Q] Need help! Did OTA update to 5.0, stuck in bootloop!

I need some major help
My N7 2012 was stock, never rooted. I had only installed OTA updates. Yesterday, the OTA update for Lollipop appeared, and I installed it.
It worked fine for about an hour, until it suddenly rebooted. After that, it will now only boot into the launcher (Nova Launcher) for about 15 seconds, then *bam* crash, reboot. Rinse and repeat.
I've tried booting into safe mode via long-pressing on the Shutdown menu, but it apparently crashes before it can reboot, because it just boots back to Nova Launcher.
I've also tried getting it into fastboot, and I can issue fastboot commands. However, I've never unlocked the bootloader. And when I try to unlock it now, I get the screen that says "This will void your warranty are you sure?" But when I select Yes, fastboot's console says "Failed", and it remains locked.
If I go into Recovery, it just says "No commmand"
I need some help from the geniuses on this forum. To me it seems like an app running at startup is causing the crash, so if I could just get it to Safe Mode, I could figure it out and uninstall it. Hell, I'd be fine w/ a total wipe at this point. Just something to get it working again!
Thanks in advance!
Try using wugfresh's nexus toolkit to fix your issue, preferably to full wipe and reinstall lollipop again.
Didn't work
bubba949 said:
Try using wugfresh's nexus toolkit to fix your issue, preferably to full wipe and reinstall lollipop again.
Click to expand...
Click to collapse
I tried using the Nexus toolkit, using Flash to Stock/Unroot in Bootloop mode, and it didn't work. A few sections succeeded, but most of the sections said "FAILED". Even after performing this, it still wants to boot to my normal desktop, so I know it's not re-flashing a thing.
I wish I knew more about this. I can get into fastboot by going to Power+VOL- but because it won't stay on the desktop, adb commands are a no-go. Is there something in the Advanced section of the Nexus Toolkit that will let me do a reflash? I'm afraid of just poking and trying things for fear of truly bricking it.
Thanks.
Sorry just re-read your last reply didn't realise you can't do adb commands, if you get to a point when you can then below may help...
I had a similiar issue caused differently what i did was to go to this link
http://forum.xda-developers.com/showthread.php?t=1907796
Downloaded the bootloader from JWR66V the guy mentions in his thread he mentions the same issue that i had which is when i tried to flash a stock or custom rom i kept getting messages about invalidstate on bootloader then the system and userdata images would fail when i tried to install...
In the end i downloaded the stock JWR66Y rom, replaced the bootloader image with the one mentioned above, i had to flash the seperate parts of the rom as the Nexus Root Toolkit wouldn't accept the MD5 after i replaced the bootloader so make sure the recovery, the modified bootloader, system and userdata are in your SDK tools folder then i did the following in cmd...
fastboot erase boot
fastboot erase cache
fastboot erase recovery
fastboot erase system
fastboot erase userdata
fastboot flash bootloader bootloader-grouper-4.23.img
fastboot reboot-bootloader
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img
fastboot flash userdata userdata.img
fastboot erase cache
Fastboot reboot
And voila it booted up and then upgraded its self and is now stock running 5.0 but its working for 2days it wasn't lol
alastria1 said:
It worked fine for about an hour, until it suddenly rebooted. After that, it will now only boot into the launcher (Nova Launcher) for about 15 seconds, then *bam* crash, reboot. Rinse and repeat.
I've tried booting into safe mode via long-pressing on the Shutdown menu, but it apparently crashes before it can reboot, because it just boots back to Nova Launcher.
Click to expand...
Click to collapse
You can try booting into Safe Mode directly from powered off state. From a reference guide here in help
bftb0 said:
[size=+1]Safe Mode Boot[/size]
From a cold start boot (press & release Power button), wait 2 seconds after the B&W Google (bootloader) splash screen appears, then press and hold Vol-Down button until the normal OS boot is fully completed (lock screen or home screen appears)
Click to expand...
Click to collapse
Sounds like something is draining the RAM. Try using the stock launcher as default.
Still crashed
dtg7 said:
You can try booting into Safe Mode directly from powered off state. From a reference guide here in help
Sounds like something is draining the RAM. Try using the stock launcher as default.
Click to expand...
Click to collapse
I didn't know that. I tried it, and I was able to boot it into safe mode doing this ... and then it crashed in 15 seconds and rebooted...
At this point, I'm considering just emailing Google, since its their update that did this.
They'll probably tell you to wipe cache partition. And by the way,
alastria1 said:
If I go into Recovery, it just says "No commmand"
Click to expand...
Click to collapse
that is a normal operation, it's supposed to say that. What you need to do to get the actual recovery menu is, with screen saying No Command, hold the power button, then click the volume Up button, them let go of power.
This will get you the recovery options, where you should scroll down to wipe Cache partition (last one I think) and select it by hitting power. Reboot into Android and see if that helped.
If not in the same recovery menu there's an option to wipe everything, factory reset. that might cure your device but it will wipe your data.
There is an adb command to pull your sdcard data off your device, but I've never tried it in stock recovery. it might work, but of course it will probably require you had turned On USB debugging.
adb pull /storage/sdcard0/ yourcomputerfolder
yourcomputerfolder being a location on your laptop, like a folder on the desktop.
try this command when in recovery, I don't think it works in bootloader. also, if it works it will only backup your regular files, not your installed apps.
if not then just do the wipe from recovery.
good luck.
Still a no go...
So, I got into the recovery menu, and did a full factory reset. After it rebooted, it went right back to Nova Launcher (with my usual wallpaper on there), and crashed as before. Getting into safe mode confirmed that it no apps were wiped. Factory reset didn't reset a thing.
Its almost like the flash memory is stuck on read-only mode. No matter what I do, nothing changes the contents of memory.
That is weird. And I suppose you can't do what 'wakers' suggested and flash the individual partitions since it probably requires an unlocked bootloader, which you already tried to unlock unsuccessfully. I'd say you were up sh-- creek without a paddle, but... Google searching, maybe there's still a tiny bit of hope:
See this discussion: http://android.stackexchange.com/qu...p-after-lollipop-flash-no-adb-and-no-fastboot
to summarize the suggestions:
- try holding the power button for over ten seconds to kind of reset... something
- try sending the command: fastboot oem lock
yes I know you never unlocked but try it anyway, it might go thru where unlock failed.
speaking of fastboot oem unlock, I know it failed but maybe you can just keep sending the command a few times, one of them might go thru.
I'd add another suggestion: carefully remove the back and carefully unplug the battery and let it sit for a while. then put it back together and try booting up.
may the force be with you.
Finally resolved
Thanks to the posters for the help. I contacted Google customer support and they're overnighting a refurb replacement for free.

CWM error cant mount-open cache/recovery

Guys, i just bought an used Nexus 4 and after flashing the cwm recovery and trying to boot in the recovery mode i get a few errors stating:
cant mount cache/recovery
cant open cache/recovery
I notice there are a few topics about this and the solution is to adb push or something, but the adb push command wont work in recovery for me, says device not found and i know my drivers are correct since i can fastboot and do stuff.
I actually got the device running perfectly flashing Chroma via sideload, but cwm wont work! I cant access anything from inside cwm... I also tried twrp and no luck.
I also tried a full original image flash, no luck
Can you please help me with this?
Thanks
luizffgarcia said:
Guys, i just bought an used Nexus 4 and after flashing the cwm recovery and trying to boot in the recovery mode i get a few errors stating:
cant mount cache/recovery
cant open cache/recovery
I notice there are a few topics about this and the solution is to adb push or something, but the adb push command wont work in recovery for me, says device not found and i know my drivers are correct since i can fastboot and do stuff.
I actually got the device running perfectly flashing Chroma via sideload, but cwm wont work! I cant access anything from inside cwm... I also tried twrp and no luck.
I also tried a full original image flash, no luck
Can you please help me with this?
Thanks
Click to expand...
Click to collapse
when you flashed the factory image it should have brought you back erasing and replacing everything. In fastboot did you flash the bootloader, radio, system partitions (.IMG), recovery partition, and so on.? If not try this steps guide http://forum.xda-developers.com/nexus-4/general/how-to-how-to-flash-factory-image-t2010312/page194 its pretty detailed but it helped me after I wiped everything off my phone trying to learn. If that's a bit too much then try searching for wugfresh nexus toolkit. Both will wipe everything from your nexus then replace it and should get everything going

Categories

Resources