Sup guys.
As the title says, my recently bought uni housing have a crack. It's located right under bottom right corner of uni's display. As far as I know it's pretty frequent damage of uni housing, and it's not doing any harm to my pda but I just don't like it. Would prefer to have it sealed ;]
There goes the question - is there anyone who tried gluing it?
Which glue would you recommend for this?
I'm thinking about model glue (does it have some other, certain name in english? I dunno about it, as english isn't my native, and I'm not into models too ;] Anyway it's the one you use to glue plastic models). It have needle, so it's precise - I don't want to left any marks of gluing on my uni.
What do you guys think? Is it even possible to glue it neatly? Is the model glue okay? Or should I pick another one? If so - which one?
Thanks in advance.
I think some might say you can get a new housing off ebay.
http://cgi.ebay.com/FULL-GREY-HOUSI...ewItem&pt=PDA_Accessories&hash=item4cedb9772e
US $42.49 ---> GPB £27.8364
just typed 'XDA Exec' in to ebay US and found: http://shop.ebay.com/i.html?_nkw=XD...&_odkw=HTC+Universal+housing&_osacat=0&bkBtn=
Also found: http://cgi.ebay.com/O2-Xda-Exec-Qte...ewItem&pt=PDA_Accessories&hash=item45f1fac0d9
Yeah, but I don't need new one. One I have actually is in good condition, and not really worn out - only this crack bothers me.
Also it's not doing any harm to pda, so paying 40$ for new housing is out of question. If there is no way to glue it (I think it will work, though), then I will just live with it ;]
am starting to get that =]
i think you should try and purchase a 6 start screw driver.
and dismantal the screen then try to glue to.
if not just spend $37 on a scrren outer housing for the screen and base
Hey everyone my HTC HD2 got the Non-Responsive screen problem a week ago, & did a lot of research and found out that it was most likely a hardware problem with a cable..... So a lot of people would tell the people with the problem that the "Touch Screen Digitizer" is dead (like the cable), or it needs to be cleaned... pretty well go out and buy a new one... BUT I have never found evidence that someone has done this and it has successfully "cured" their HTC HD2 Non-Responsive touch screen problem...
So I was looking for anyone on the forums that could confirm this is a solution or give me any tips on what I should do.... AND no I don't have enough money to get a new phone, nor do I live in the USA so I can't send it in to fix it...
This is what I was going to buy for it:
http://www.ebay.ca/itm/NEW-OEM-HTC-...781?pt=LH_DefaultDomain_0&hash=item519a3d2e45
Thanks for taking the time to read my Thread, its much appreciated!! I hope I can find a fix!!
PS: If anyone wanted to know what it looks like out of curiosity I posted 3 pictures with RED circle HIGHLIGHTING the problem when I try to touch something....
My digitizer has been a bit dodgy for the past few months. It's ironic that when I finally found out what the issue was and called HTC, my factory warranty had ended exactly 4 days prior to the call.
Fast forward 3 months and my phone has now been unresponsive for 3 hours despite my prying and tweaking various hard parts.
I disassembled the phone down to the main board just to see how hard the install is, but it's a bit intimidating once it's time to start pulling all the film and ribbons. A bit too tight and small parts for my liking.
Time to hit CL to see if I can find a cheap replacement.
Good luck with your repairs. I may be following in your footsteps if I can not find a good deal.
Yeah I will see how well it goes... if anyone has useful info, i will be more than grad to hear it
Thanks
Many people attempt to replace a digitizer, but I simply don't recommend it, we see enough of do-it-yourselvers who created problems in addition to the original ones.
What I do recommend, however, and I stated it on many threads already, is to get an LCD+DIGITIZER assembly. Simply because it is easier to fit. Not saying the overall fitting is easy, always depends on your overall skill, so ensure that you are familiar with the procedure BEFORE you begin. But you will save yourself a lot of trouble by getting the whole thing, as opposed to the digitizer only for the sake of a few bucks.
However, if anyone still feels intimidated by the whole thing, I am on the lookout for working main board. Advertised a few times in the marketplace with limited success. So if anyone smashed their baby and will be looking to replace, rather than repair - drop me a PM. I am in NZ. Will pay by Paypal.
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
How much did the set cost?
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
Thanks I will check it out, hopefully it won't be to hard and I hope I can repair it!! oh and could you post a link of the youtube & manual you used to replace your screen?? Thanks
Oh would anyone suggest then just calling HTC and sending it to them to repair?? or does that cost to much??
Thanks everyone for the help
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Heronization said:
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Click to expand...
Click to collapse
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
GnatGoSplat said:
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
Click to expand...
Click to collapse
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Heronization said:
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Click to expand...
Click to collapse
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
GnatGoSplat said:
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
Click to expand...
Click to collapse
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Heronization said:
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Click to expand...
Click to collapse
Yeah, no prob. I can post a pic of the digitizer lifted from the frame which shows where the adhesive tapes are that you have to go through, if it would help.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Heronization said:
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Click to expand...
Click to collapse
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
GnatGoSplat said:
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
Click to expand...
Click to collapse
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Heronization said:
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Click to expand...
Click to collapse
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
GnatGoSplat said:
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
Click to expand...
Click to collapse
Alright thanks I have to go and don't know when I'll be back, but I will try it tonight and hopefully I don't break anything...
Thanks for the help!
Hi,
after my wife dropped my phone (accidently she swears) I have some small scratches on the phone. (See Picture below)
Someone knows some ACME Cleaner&Scratch remover for that?
Greetings .. seems that I have had the HD2 for the longest time ...
OOO!! Ouch! Looks like it's time to see the phone doctor. Or, if you feel brave enough, you can fix it yourself. They have replacement screens on ebay. Since you have the EU model the contacts for the screen and the digitizer are soldered together. So you have 3 options. 1. Take it to someone else to fix it. 2. Attempt to order just the digitizer and if you have some time and surgical skills solder the contacts yourself or, 3. Get a fully assembled LCD and digitizer that is already soldered together and swap them out. The cheapest would be to just get the digitizer but if you have to factor in the time and headache of soldering those tiny contacts together, I think getting the assembled parts would be my choice. The US T-Mobile model has a small plug-in type connector on it so there is not soldering. I replaced mine and it is quite a chore. You have to be very careful and don't rush it or you will break things. Good luck!
Yeah you've got more than scratches there! You've got a smashed screen
You'll have to replace the glass
the guy above stated pretty much everything you need to know but here's a link to a lcd+digitizer combo that is fairly cheap: http://www.ebay.com/itm/New-LCD-Dis...192999?pt=PDA_Accessories&hash=item45fdf14d27
I know guys, the scratches where just kidding
The complete replacement has been ordered already, will fix it by myself
RollerCoasting said:
Yeah you've got more than scratches there! You've got a smashed screen
You'll have to replace the glass
the guy above stated pretty much everything you need to know but here's a link to a lcd+digitizer combo that is fairly cheap: http://www.ebay.com/itm/New-LCD-Dis...192999?pt=PDA_Accessories&hash=item45fdf14d27
Click to expand...
Click to collapse
He was being sarcastic with the 'scratches' thing :L
MasterMerlin said:
I know guys, the scratches where just kidding
The complete replacement has been ordered already, will fix it by myself
Click to expand...
Click to collapse
That's great. Like I said be very careful in taking it apart. Especially the flex cable that controls the volume rocker. Take your time and you can get it fixed.
Check out this website: http://pocketnow.com/hardware-1/official-htc-hd2-disassembly-assembly-training-videos-leaked
It has some videos on disassembling and assembling the HD2 just so you see what you have to deal with. Also another good investment would be to see if you can get some double sided tape to stick the back of the LCD to main frame if you can't salvage the stuff that's there already. It can't be too thick though because you'll run into problems of getting it put back together. They have that on ebay also.
yes
option one.... change screen..
option 2...change wife.....
hahaha change your wife my friend
htchd2fix said:
yes
option one.... change screen..
option 2...change wife.....
Click to expand...
Click to collapse
haha change screen is cheaper i guess