Hey folks, i have a HD2 which isn't turning on. I received a call and it just switched off. Now there is no activity in it at all. No led when connected to a charger. I had MIUI installed on the phone.
The repair people say that the motherboard needs to be replaced which would cost approx 12000INR.
Any way i could revive it back?
Please suggest. Thank you!
Sent from my ST25i using Tapatalk 2
Rapier07 said:
Hey folks, i have a HD2 which isn't turning on. I received a call and it just switched off. Now there is no activity in it at all. No led when connected to a charger. I had MIUI installed on the phone.
The repair people say that the motherboard needs to be replaced which would cost approx 12000INR.
Any way i could revive it back?
Please suggest. Thank you!
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
You can try the the freezer trick, put the device in a zip lock bag and put it in the freezer for a few minutes and then see if you can turn it on or charge it. You can also take a old USB cable and cut the mico USB end off and strip the wires back then touch the read to the + on the battery and the black to the - on the battery for a minute or two and then try to boot the device. I sorta souds like you were using MAGLDR and the battery died. You can not charge the device while it is off with MAGLDR. So I would try charging the battery first.
Thank you for replying. You're right i was using Magdlr. I'll try what you said
Sent from my ST25i using Tapatalk 2
I've got the exact sam prob, the HD2 was using MAGLDR, and now it won't start (except for a few times it did), but I honestly can't figure how - since once it had been charged on an external batery charger, and then it turned on and worked for a while, but now it won't work with a charged battery...because I tried using it with another HD2 phone's battery which also has MAGLDR and which works (even with my phone's battery).
The pins have been changed, and it worked then also for a while I've been said, but it's not working again now.
Any help please?
TIA
P.S. I've tried ziplock...15min...nothing :/ How to try the USB? Which wires should I connect to which pins please?
T-Macgnolia said:
You can try the the freezer trick, put the device in a zip lock bag and put it in the freezer for a few minutes and then see if you can turn it on or charge it. You can also take a old USB cable and cut the mico USB end off and strip the wires back then touch the read to the + on the battery and the black to the - on the battery for a minute or two and then try to boot the device. I sorta souds like you were using MAGLDR and the battery died. You can not charge the device while it is off with MAGLDR. So I would try charging the battery first.
Click to expand...
Click to collapse
something like this
https://www.google.com.hk/search?um....0.0.258.258.2-1.1.0...0.0...1c.1.lFN-ufsMSJw
but be very carefull, if you have an external batt. charger that would be best
dada.81 said:
Which wires should I connect to which pins please?
Click to expand...
Click to collapse
clue in post 2
T-Macgnolia said:
You can also take a old USB cable and cut the mico USB end off and strip the wires back then touch the read to the + on the battery and the black to the - on the battery for a minute or two
Click to expand...
Click to collapse
or mini usb, or even an old usb printer cable, with the chunky end, , it doesn't matter which type.
Thanks samsamuel,
Seen the +/- signs on the back of the battery late, after having meassured the voltage, which is 4.14V (should I do the USB charge then even and how long is it safe since my battery powers up another HD2)?
TIA
if teh battery works in another device, then no, theres no point, its not that.
4.14 is fine, i think it goes up to about 4.2/4.3 when full, drops to the low 3.x when drained.
If the freezer trick didn't help either, then its gotta be either hardware, or something totally catastrophic, so if its an option for you, id try JTAG, failing that, id be considering using it for parts, , buying one with a cracked screen perhaps, and swapping your screen into it, ,
dont take my word for it, though, read learn and try things, you never know.
Related
I went to sleep two days ago and my droid ran out of battery, i have try to recharge it , but i only get a green light and wont turn back on ,,, I have removed the battery also the sd card hold home and power and nothing seams to work !!! any suggestions that i need to try before taking it to exchange
How long did you charge it for? The DX wont turn back on if the battery completely dies and hasn't been charged to at least 20% I believe.
Sent from my DROIDX using XDA App
i recharge it for abt 8hrs.. i just came back from two differnt verizon stores and they dont know about it or how to fix it.. they say might have to get another ...
Did they try a new battery??? Replace the battery, first, before replacing the X...
yeah coz no body has try a new battery on it .. im gonna have to go to best buy and see if they have one there even tech at verizon they said dont have battery for that phone there and they should right .. .. ill try a new battery if that doesnt help then im gonna have to order a new phone
Thanks guys just came back from verizon store .. and Finally somebody did what Str0ntium and i want them to do .. try a new battery .. my was out of juice so that why it wouldnt power up or recharge.. .. different Person at Verizon store tried the battery from his own DX .. and my phone turned on . once the was done , he let the battery charge for like 5% on his phone . then put it back on my phone . witch turned on and started charging normally .., im thinking on buying the xtended battery .. they said might give me like xtra 2 more hours .... will see what happens... .. i just got frustrated that to have somebody to try a new battery took me like 3 days .. very poor custumer service thats all i can say ..
I had the same thing happen to me a month ago. Can't find the link right now where I learned this right now but you have to do some jerry riggin to fix this. You have to take a usb cable and cut off the end that would plug into the device, find the red and black wires and wedge them between the proper terminals between your phone and the battery. If done right you can get power to the device to turn it on. Once on just remove the usb fast and plug into a normal outlet. Had to do this a few times and if done right works like a charm.
Sent from my DROIDX using XDA App
I ll keep that in mind in case i ran in to something similar .. but hopefully i wont have to do it .. hehehe !!
Dead DroidX
If you allow your Droidx to fully discharge, it does not have enough power during inital recharge off a computer connected USB to get the recoginition that the device needs to be charged vs data tx. Just use your wall charger (Dumb Charging Unit w/no data line) no need to modify your cord. Just do not let get com[letely discharged and you will not have this problem.
xxprodigyxx11 said:
I had the same thing happen to me a month ago. Can't find the link right now where I learned this right now but you have to do some jerry riggin to fix this. You have to take a usb cable and cut off the end that would plug into the device, find the red and black wires and wedge them between the proper terminals between your phone and the battery. If done right you can get power to the device to turn it on. Once on just remove the usb fast and plug into a normal outlet. Had to do this a few times and if done right works like a charm.
Sent from my DROIDX using XDA App
Click to expand...
Click to collapse
I saw something similar but instead of wedging it in between the phone and battery I used some electrical tape and stuck the red and black wires from the usb cable directly to the battery. I let it sit for an hour and then I was good to go.
Sent from my DROIDX using XDA App
Next time charge it on the wall charger instead of a USB cable...
Yep happened to me a few weeks ago... I had a broken bootloader which you have to have in order to charge the phone. I just sacrificed a usb cable, I cut the ugly side with the usb-b form factor, and used a couple paperclips to pin the battery down. It took about two and a half hours to get full... just remember red on red, black on black.
DroidX x2, Droid2, Droid1, DInc, and LG Ally x2 makes for a big Verizon bill.
Bad droid, no Doughnut!
MSMoney said:
If you allow your Droidx to fully discharge, it does not have enough power during inital recharge off a computer connected USB to get the recoginition that the device needs to be charged vs data tx. Just use your wall charger (Dumb Charging Unit w/no data line) no need to modify your cord. Just do not let get com[letely discharged and you will not have this problem.
Click to expand...
Click to collapse
Hahaha your right. I was to stupid. Thanks bro.
Need some help hope i post this in the right place. i have gingerbread on my HTC HD2 and was converting back to windows to sell on ebay and i started it was almost done when i relised before i started i forgot to charge the battery and it ran out before it was done know the phone what turn on at all. i plug it in the wall charger nothing, plug it into the computer nothing tried everything nothing. do you think that the battery is that dead and it was in the proccess that the chargers dont work on it no more. would it work maybe if i had a charged battery to put in it. it mite come back on. any help would be great thanks.
lpartridge said:
Need some help hope i post this in the right place. i have gingerbread on my HTC HD2 and was converting back to windows to sell on ebay and i started it was almost done when i relised before i started i forgot to charge the battery and it ran out before it was done know the phone what turn on at all. i plug it in the wall charger nothing, plug it into the computer nothing tried everything nothing. do you think that the battery is that dead and it was in the proccess that the chargers dont work on it no more. would it work maybe if i had a charged battery to put in it. it mite come back on. any help would be great thanks.
Click to expand...
Click to collapse
Just keep it plugged in for 1-2 hours and then try booting in to try color screen bootloader and go from there.....
If you have MAGLDR installed then you can not charge the battery when the phone is off.
You should try to charge the battery using an external charger.
Edit: If you have a friend with HD2 and windows Mobile 6.5 then you could use the phone to charge you battery.
Wrong, you can charge it while it's off.
StephanV said:
Wrong, you can charge it while it's off.
Click to expand...
Click to collapse
really? are you sure? because there are a lot of references to the magldr bug that wont allow charging (or even powering on without pulling the battery) if you try to charge with the phone turned off.
well i tried to charge for the last 2 hours nothing tried to remove battery nothing. Iam going to try and find a charged battery to see if the phone mite turn on or something. ill post later to let yall know what happen tho. thanks for the help.
samsamuel said:
really? are you sure? because there are a lot of references to the magldr bug that wont allow charging (or even powering on without pulling the battery) if you try to charge with the phone turned off.
Click to expand...
Click to collapse
Just give it a try man and see for yourself whether it charges or not....
what are you guys fighting about man, they just updated the magldr v1.3 and yeah we can now charge the phone while its off
Sukuya said:
what are you guys fighting about man, they just updated the magldr v1.3 and yeah we can now charge the phone while its off
Click to expand...
Click to collapse
Wrong x2.
1. No one is fighting.
2. With new magldr, phone turns itself on when plugged in. Charging when off is not possible. The battery requires management which is only implemented in software. It may hold a small charge if you have magldr installed, but it won't charge fully, or properly. Also, it's not likely he's got the new magldr if he's returning back to windows.
Lastly, for the OP, what method did you use to return to winmo? And which winmo rom did you use?
Sent from my HD2 NANDroid using XDA App
Find a way to charge your battery and everything it's going to be just fine.Your phone it is going to work.
Changing the battery should work.
I'm new here so basically with new 1.13 or later phone can't be charging if it's not turned on?
Makić said:
I'm new here so basically with new 1.13 or later phone can't be charging if it's not turned on?
Click to expand...
Click to collapse
Read? Phone turns itself on if you connect a charger. Phone has NEVER charged while off with nand. This way at least you don't have to pull the battery to turn the phone on.
Sent from my HD2 NANDroid using XDA App
Just in case: If you on same situation that described on first post try this:
Q: If you completely run down the battery, would you be able to charge it with the phone again?
A: If your battery is dead, press and hold Vol Down and plug in USB cable / charger at same time. Phone will boot into bootloader and charge there just fine. Leave for 20 mins, pull battery, reboot and charge normally. If phone has just run down, plugging in the charger will usually turn it on.
Its found on one NAND thread and goals goes to g.lewarne
Actually i was on same situation and this helped on first try.
check the connection between battery and phone , the metal things i mean.
Perhaps, it is off the subject, but...
Poster #1: why do you want to get rid of this beautiful phone?
Just curious...
ok i bought another phone and i took out the charged battery from it and put it in the bricked HTC and it does nothing. now i know it was almost reverted back and i think the battery ran down but Iam not completely sure but maybe it could have been in the reverting software i used and maybe it just like lock up or something cause at that point you couldnt see the battery indicator. now i guess ill just have to sell on ebay for parts but it would be cool to try and un-brick it or try and figure it out.
So we all know the major problem with the WP7 roms.
You can not charge your phone when battery is completely drained!
Now here is the solotion. This requires no apps, no mods. Just your own handeling!
So what to do when battery depletes?
1. Plug your phone into a powersuply.
2. Turn on the phone and keep the power button and both volumes buttons pressed. (this is called a hard reset.)
How to hard reset HD2, view the first 17 seconds. Ignore the VolUp!.
3. You will receive an message saying:
''This operation will delete all your personal data, and reset all settings to manufacturer defailt. Press VolUp to restore manufacture default, or press other keys to cancel.''
Click to expand...
Click to collapse
4. Do not press anything. Let your phone be for a couple of minutes. I keep my phone laying for a minimum of 10 minutes.
You won't see the phone charging (no orange light in upper left corner)! Believe me it is!
5. After 10 minutes restart the phone. If ''press any other button to cancel'' does not work. Take out the battery, keep battery out for 5 seconds. Restart phone.
6. Phone will start. After windows phone loading screen you will see the phone is charging. If you kept it on power. If not, you didn't follow my instructions.
Tip: to avoid battery drainage!
When the phone is making the bleep noice warning for critical energy level, turn off the phone and keep it at a warm location. Ideal is to take out the battery and keep that to as warm as possible. Batterys barely drain when they are in warm enviorments.
I am not responsible to any damage done to the phone!
I done this multiple times, all times it worked fine for me!
If it helped, Thank me and leave a comment
when i'm on the road there is only one warm place i could think off, besides my armpits...
but your method works, have faced it once.
Thanks for the conformation.
To bad the HD2, is kinda big... doesnt sit that well.
magldr works as well
whats not clear is if the battery controler is in use with this method, so be warned, dont leave it too long, if you charge it for no more than an hour it will be ok
mains power adaptors usually give out 1Ah, take in to account that the screen is on full, this should give you around 700mA, more than enough to get in to windows to charge propperly
USB charge will be half that, most USB ports only give out 500mAh so an hour will give you approx 200mA again, thats enough to get you in to windows
Overcharging a battery can have some side effects, firstly is reversed polarity, meaning it wont take as much charge in the future, or it could heat up a lot, which isnt good for anything, the life of battery or the device its self.
dazza9075 said:
magldr works as well
whats not clear is if the battery controler is in use with this method, so be warned, dont leave it too long, if you charge it for no more than an hour it will be ok
mains power adaptors usually give out 1Ah, take in to account that the screen is on full, this should give you around 700mA, more than enough to get in to windows to charge propperly
USB charge will be half that, most USB ports only give out 500mAh so an hour will give you approx 200mA again, thats enough to get you in to windows
Overcharging a battery can have some side effects, firstly is reversed polarity, meaning it wont take as much charge in the future, or it could heat up a lot, which isnt good for anything, the life of battery or the device its self.
Click to expand...
Click to collapse
That is true, but I recommend trying it for a minimum of 10 minutes keep it on charge. and as soon as windows pop on it recharges normally.
And didnt knew magldr did the job as well, the only problem is if you deplete it to badly it doesnt go past the HTC screen in the beginning.
all this is completely unnecessary.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
lemonspeakers said:
all this is completely unnecessary.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
Click to expand...
Click to collapse
I did not know that.
Well thank you. Although I am not such a big fan of taking out the battery when its not needed. I mean the change is short circuits with the connecting points when taking out, when powered or putting in when powered it larger. Now I heared from a comment above that MAGLRD does the trick as well. Now that is far more easier then all the others given above, Yours and mine
good tutorial on this. I cant believe the battery wont charge when dead thought this was a faulty error of the phone.
I flash boyppc rom v5 and my battery drained completely and now it doesnt start up I tried both methods available here. Please help.
faiz1120 said:
I flash boyppc rom v5 and my battery drained completely and now it doesnt start up I tried both methods available here. Please help.
Click to expand...
Click to collapse
theres 3 methods on here,
bootloader charge
magldr charge
remove battery charge
all three will benifit frm heating up the battery, do not cook it, or it may blow up
there is a 4th way but i dont recomend it unless nothing else works
take a usb cable mini or usb printer cable
cut off the end connector
strip back the wires and seperate them all, you want the red and black ones
make sure all the wires cant touch each other, cover the 2 unused wires with tape i
then connect the black wire to the (-) negative and the red wire to the (+) positive
tape them in place
the 3rd contact point on the battery isnt used in this method
finally connect the other end of the usb cable to the computer
dont leave it too long and when disconnecting remove the computer end first
faiz1120 said:
I flash boyppc rom v5 and my battery drained completely and now it doesnt start up I tried both methods available here. Please help.
Click to expand...
Click to collapse
I recommend this one.
It bypasses the system somewhat. Don't know what happens when battery is entirely drained, but it is worth a try.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
If it does not help. You can buy a new battery.
Click Here. Its not that expensive, a official new battery from HTC is around 30$is around 20Euro's.
lemonspeakers said:
all this is completely unnecessary.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
Click to expand...
Click to collapse
Thanks for this timely post Lemonspeakers. completely drained the battery listening to music on loudspeaker and didnt hear any warning. Couldn't hard reset then checked this thread.
On putting in the battery after charging the empty phone, the screen kept cycling between mgldr and HTC splashscreen so booted into sd android and the phone is fine.
I assume I didnt charge the empty phone for long enough (30 secs), I didnt warm the battery and I suppose I could have left it cycling until it charged up a bit more.
Thanks again
Toasit said:
I recommend this one.
It bypasses the system somewhat. Don't know what happens when battery is entirely drained, but it is worth a try.
easy fix solution:
1. Pull the battery out and USB cable out (if connected and charging)
2. Plug the USB into the phone and allow it to charge without a battery (it will not, duh!)
3. Put the battery in while the HD2's connected to the USB charging.
4. Observe that you can boot all the way back into WP7.
enjoy.
If it does not help. You can buy a new battery.
Click to expand...
Click to collapse
i tried but my phone doesnt start even then. my friend said it might be a kernel. i wanna flash stock but i dont know how because my phone isnt starting
my hd2 is a tmous. the 1024 one
Robbie P said:
Thanks for this timely post Lemonspeakers. completely drained the battery listening to music on loudspeaker and didnt hear any warning. Couldn't hard reset then checked this thread.
On putting in the battery after charging the empty phone, the screen kept cycling between mgldr and HTC splashscreen so booted into sd android and the phone is fine.
I assume I didnt charge the empty phone for long enough (30 secs), I didnt warm the battery and I suppose I could have left it cycling until it charged up a bit more.
Thanks again
Click to expand...
Click to collapse
your phone was not starting either? like it was black even though you pressed hard reset? how long do i leave it the empty phone to charge??
I "charged" it for about 30 seconds, suppose you could do longer
Robbie P said:
I "charged" it for about 30 seconds, suppose you could do longer
Click to expand...
Click to collapse
I left the phone without the battery and left it plugged in for 2 hrs and still no luck.
faiz1120 said:
I left the phone without the battery and left it plugged in for 2 hrs and still no luck.
Click to expand...
Click to collapse
This would be funny if it wasn't so serious.
Have you tried warming the battery? Hairdryer warm
Dont know if you have mgldr so maybe try the hard reset option
Robbie P said:
This would be funny if it wasn't so serious.
Have you tried warming the battery? Hairdryer warm
Dont know if you have mgldr so maybe try the hard reset option
Click to expand...
Click to collapse
I have magdlr but I can't even get it into hard reset. I can try the hairdryer warm the battery
faiz1120 said:
I have magdlr but I can't even get it into hard reset. I can try the hairdryer warm the battery
Click to expand...
Click to collapse
That might work.
Otherwise maybe a phone repair shop, there is equipment that can charge your battery outside an phone. An emergency charger its called if I am not mistaken.
you could inform there.
its showing symtoms of it bring bricked. cause it doesnt charge, it doesnt turn on without the battery, and yeah conclusion is that its dead!
hey guys.
charged battery at night used it at work all day came home around 10 and battery was on 1%..went upstairs to charge but phone but was dead. when plugged into wall phone boots for 2 sec then turns off and boots again for 2sec....constantly looping like this? im pretty sure i just need enough charge so that i can boot into android and ill be sweet. but doesn't even get half way there!?
need help. cant charge.
im leaving the battery out for the night and im gonna try again tomorrow but any suggestions would be great!
thanks
Not sure but you can try this: hold down power button till mgldr menu comes. Stay in mgldr menu for some time and get some charge,then reboot.
Sent from my HTC HD2 using XDA Premium App
Phone will not charge on magldr screen. Android needs to be booted to charge.
Get old USB cable, mini or micro, cut end off, bare red and black, take battery, connect red to + and black to - ,plug into wall charger and hold wires on battery for a minute or so, reinsert battery, should be charged enough to get far enough into booting to start charging.
First.. i had the same problem.
it have to charge while off.
before you cut off things, check the batterypins. one of them was broken on my HD2 (i saw one of them below my battery).
if so, try to hold that broken pin back while insert the battery and try again.
you could also buy a dockingstation (something like that: http://www.amazon.com/Fosmon®-Premi...P2YS/ref=sr_1_4?ie=UTF8&qid=1313518480&sr=8-4) to charge batterys.
I had the same problem once, I`m not 100% sure how i solved it but I think that I pluged it in that it started booting and removed then the battery. I think it doesnt start automatically if you reinsert the battery then... but I´m not sure about it...
mmattes said:
I had the same problem once, I`m not 100% sure how i solved it but I think that I pluged it in that it started booting and removed then the battery. I think it doesnt start automatically if you reinsert the battery then... but I´m not sure about it...
Click to expand...
Click to collapse
thats correct, but relies on the bootloader being able to charge when off, so this method of fixing the discharged battery problem only works with winmo or cLK
Your right i had that Problem in the time i was running it with winmob andere haret
Sent from my HD2 using XDA App
Charge while in bootloader or hard reset screen, it should charge from there.
However, the charging process using the aforementioned methods is kind of slow.
hey guys. thanks for your responses. i have left it overnight and it doesnt get to the 1234 bit. i have 3-4 cords so i cut one up however it has blue, red, white and green cords....whats positive and whats negative?
also my pins are fine.
this is killing me!
Thank you to samsamuel, i ended up cutting my old cable. connected the red cable to + and the white cable to - and left it for a hour. just booted my phone back up and got 1000 msgs and emails lol and im on 84% battery.
thanks again to everyone how posted!
much appreciated!
Good to hear,, for anyone else thinking of trying it, an hour is pushing it a bit, you are running the risk of damaging the battery since the charge control circuits aren't being used.
What Android build is this? I remember having a build once that required a special key combination to charge the phone up. I think it required you to hold the volume down and power while plugged in to the charger and it could charge from there. I don't remember exactly though.
mziol said:
What Android build is this? I remember having a build once that required a special key combination to charge the phone up. I think it required you to hold the volume down and power while plugged in to the charger and it could charge from there. I don't remember exactly though.
Click to expand...
Click to collapse
Nothing to do with the build,,, if you have magldr installed the phone must be on and booted into android to charge.
samsamuel said:
Nothing to do with the build,,, if you have magldr installed the phone must be on and booted into android to charge.
Click to expand...
Click to collapse
EDIT: I realize now that it must have been something else, can't charge in HSPL or MAGLDR (duh). I have no recollection of what though (if anybody knows, let me know because it's driving me nuts now!)
OP, you do also realize that instead of cutting up wires you could get an external charger for your battery and just charge the battery alone, right? If you've wanted to buy one of those fancy desk docks you could get one that also charges a battery behind the phone
Hi,
So i Had this Htc HD2 . I got it as a gift from USA. I've used it like 2/3 month. I installed MIUI rom on this device. And then i hot another phone and didn't used that phone anymore. But today i found this phone and i tried to turn it on. Then I saw that the phone isnt turning on. It just stays black and just vibrates. I dont know what is wrong with this. I live in Bangladesh. We dont have any HTC customer service stores here. So i need help with this. If anyone can Help please let me know. and by the way its TMOUS HD2.
Check battery pins are contacting correctly.
Check battery voltage - lower than 3.2V try charging the battery externally & not in the HD2, if you do not have an external charger you can use a USB cable & cut mini/micro usb plug off then touch the red+ & black- wires to + - battery terminals for about 1 minute or bit longer if battery completely flat then put it back in HD2 & see if can boot.
tusher.rozario said:
Hi,
So i Had this Htc HD2 . I got it as a gift from USA. I've used it like 2/3 month. I installed MIUI rom on this device. And then i hot another phone and didn't used that phone anymore. But today i found this phone and i tried to turn it on. Then I saw that the phone isnt turning on. It just stays black and just vibrates. I dont know what is wrong with this. I live in Bangladesh. We dont have any HTC customer service stores here. So i need help with this. If anyone can Help please let me know. and by the way its TMOUS HD2.
Click to expand...
Click to collapse
Are you sure it's not just out of battery? If it had NAND Android installed on it via MAGLDR and you didn't bother turning it off then it could have just run out of charge. Since you can't charge the phone when it's off in MAGLDR, you'll have to cut open a USB cable which hopefully @samsamuel will come along and tell you about since I always forget what has to be connected where.
If you know it isn't the battery, then can you boot into the bootloader (hold vol down + power)? If you can get to that then you can try flashing a WinMo stock ROM to confirm it isn't some sort of hardware issue.
Mister B said:
Check battery pins are contacting correctly.
Check battery voltage - lower than 3.2V try charging the battery externally & not in the HD2, if you do not have an external charger you can use a USB cable & cut mini/micro usb plug off then touch the red+ & black- wires to + - battery terminals for about 1 minute or bit longer if battery completely flat then put it back in HD2 & see if can boot.
Click to expand...
Click to collapse
Tried that. Nothing happened. The phone just constantly vibrates.
Nigeldg said:
Are you sure it's not just out of battery? If it had NAND Android installed on it via MAGLDR and you didn't bother turning it off then it could have just run out of charge. Since you can't charge the phone when it's off in MAGLDR, you'll have to cut open a USB cable which hopefully @samsamuel will come along and tell you about since I always forget what has to be connected where.
If you know it isn't the battery, then can you boot into the bootloader (hold vol down + power)? If you can get to that then you can try flashing a WinMo stock ROM to confirm it isn't some sort of hardware issue.
Click to expand...
Click to collapse
I wasnt sure if it was battery or not. And then i recharged the battery with a external charger and tried to turn it on. But no luck. it stays just the same. and i cant even get into boot loader (tri color screen). NO nothing. it just vibrates.