guys i got today hd2 from a friend of mine but the problem is when i turn it on it shows a logo of htc and nothing else.
how can i format it and turn it into android with SD card?
burimi007 said:
guys i got today hd2 from a friend of mine but the problem is when i turn it on it shows a logo of htc and nothing else.
how can i format it and turn it into android with SD card?
Click to expand...
Click to collapse
Boot into the bootloader (hold power+volume down) then flash a stock WinMo ROM (make sure it's for your particular device i.e. TMOUS/EU). From here, you can do whatever you like really, it's probably best to start off with SD Android, trying out each different type of ROM (e.g. MIUI, CM9, Sense, AOSP etc.) and then move to NAND Android once you've made a selection. Note that NAND is much faster than SD, so if you feel sluggishness it might not be there on NAND.
Nigeldg said:
Boot into the bootloader (hold power+volume down) then flash a stock WinMo ROM (make sure it's for your particular device i.e. TMOUS/EU). From here, you can do whatever you like really, it's probably best to start off with SD Android, trying out each different type of ROM (e.g. MIUI, CM9, Sense, AOSP etc.) and then move to NAND Android once you've made a selection. Note that NAND is much faster than SD, so if you feel sluggishness it might not be there on NAND.
Click to expand...
Click to collapse
please can you make it a bit more clear to me,i only have SD Card is there any way to install android through SD Card
i installed winmo 6.5 but now it shows only first logo
HTC quietly brilliant and it freezes here
what should i do what should i update before i install winmo
guys and ideas,it viberates like 6-7 times and it freezes? is this software or hardware issue
sounds hardware to me, or corrupted/stuck radio. the several vibrates would point towards hardware.
Tried the freezer trick?
samsamuel said:
sounds hardware to me, or corrupted/stuck radio. the several vibrates would point towards hardware.
Tried the freezer trick?
Click to expand...
Click to collapse
i tried to put it in freezer and it got cold i turned on and nothing happend i don't know what else to do
any help please??
guys what do you suggest me to do? to send it to repair service or try anything here?
guys if i change motherboard does it get back i mean unbricked?
i installed cLK but i can't get into cwm recovery
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
should i update somethink or install any kernel
Related
I bought my HERO just a few days ago.
Once,the system halted and I took the battery out of the phone.
After that,when I turn on the phone,it show the first picture in the attachments
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and then only when I press the DIAL button ,the phone responses,and it shows the second picture in the attachments
I have checked that the buttons of the phone are all OK.
And I have sent it to someone to mend it,he said that the phone can not be connected to the computer,but he succeeded in flashing it with the miniSD memory card. BUT the phone still has the same problem.What's more ,the H-BOOT has been flashed by him from 1.76.005 to 1.76.007. But the problem still
exist....
Can anybody help me?...
And I'm from China,my English is not very good...
This might help...
g0mib0y said:
EDIT: DON'T UPDATE TO 2.1 AGAIN SINCE IT WILL HANG ONE MORE TIME. WAIT FOR HTC TO RESOLVE THIS ISSUE!!!!!!
EDIT 2: BACK UPP ALL YOUR DATA FROM YOUR MEMORY CARD FIRST!!!
EDIT 3: How did I find this out? I talked to a very helpful HTC suport rep (yes they do actually exist in Sweden). He helped me do these steps and so I thought I should share this.
Ok so you got a message that 2.1 was available for your Hero - FINELY! and you installed it using OTA. And then you got a triangle with a ! in it and you rebooted and all it says is "HERO".
This is how to solve it!
Take out your memory card. FORMAT TO <span style="font-weight:bold;">FAT32</span>!!!
Download the RUU 2.73.405.5 from HTC support homepage
Run the installation.
When it fails to find your phone <span style="font-weight:bold;">DON'T EXIT!!!</span>
If you are using Windows 7 go in to c:\Users\<span style="font-style:italic;">yourusername</span>\AppData\Local\Temp
Search for ROM.zip
Move to desktop
Rename to HEROIMG.zip
Transfer to your newly formated memory card now with FAT32 file system
Put memory card into phone
Start phone holding volume down pressed.
It will now check zip fil and then ask if you want to install.
homekey for YES
After installing you have 1.5 again and can safely upgrade to 2.1 OTA
Click to expand...
Click to collapse
Haret photon 7227 is not possible to open the file...?
rui_sandra said:
Haret photon 7227 is not possible to open the file...?
Click to expand...
Click to collapse
try with a hammer...
or read [TUTORIAL] Install Android on HTC HD Mini
I followed this tutorial but from this error ...?
Thanks.
If you want Android on your phone HTC HD Mini, Download the Cotulla's Android 2.1 and you extract the files.. these files will are together and you bring them to the root of SD card and format with FAT32 before bringing files, And when you want to start android tap on named HaRET, That is it, and if you see doesn't work it's because if SD is not enough fast or bad SD.
This files isn't about open file or something else, it's only boots to Android Operation System
Please everyone before asking, see the page, you see it, just ask about haven't asked yet....
iPlasm said:
Please everyone before asking, see the page, you see it, just ask about haven't asked yet....
Click to expand...
Click to collapse
Before I ask any questions I have read and did everything in this tutorial but it's always error opening the photon Haret 7227.
You must be the most intelligent of the forum, you should know everything.
Thanks.
Well then, Well done if you did read all of it.
We will like to know all the problems of this android, but not always same, and explain full your question, I mean.... for example what do you mean error of this?? you mean when you tap on HaRET shows you error or something?, so here you must say i have bring files to SD also to know us what have you did.. As the page of Android mini... you see some questions are same...
I think i have the same problem , after i had clicked on HARET there comes the sentences : HaRET: Booting Linux. and this is on my screen and then i must take my phone off
This is my problem.
Thanks.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
rui_sandra said:
This is my problem.
Thanks.
Click to expand...
Click to collapse
lol .......
Because your SD Card is not signed with a trusted certificate & So it's fails to load. so maybe you formatted by Computer's Format Tool.
And There're two ways to fix this, just do one of them: number one is easier, but number two can be formatted with PC's anytime without this stupid certificate;
Number 1' Format your SD by the Windows Mobile Default one; (Start>Tools>Format SD) Done!
Number 2' Read this http://forum.xda-developers.com/showthread.php?t=720782 After these reading and doing steps you are ready to run HaRET.
And here will be Answered your Question! beside this question has been asked in the Cotulla's Android Page, but no problem... and You're Welcome
bye
Solved my problem.
Thanks.
You know where I can find solution to get ip address by wirelless (wi-fi)?
Thanks.
Hy guys, sry if this was allready discussed but i'm having a serious problem: i've flashed my moms hd2 to android some months ago and after some time it began to have problems meaning the screen stoped responding...i've tried several new flashes and nothing, just after the hole process is done the screen still wont do anything...please sugestions...fix it sehow, reflash wm 6.5?!!!
You say after some months the screen stop responding as in no respond at all to touch and any hard buttons? Then how can you flash anything when touch screen/hard buttons unresponsive?
For me it is the hardware problem. Flashing won't help...
if your screen completely stopped working the digitizer is broken and you'll either have to get another hd2 or if you're in your warranty period send it back in and have it replaced. my first hd2 had the same problem but luckily i was in my warranty period so i sent it back it (cost me $10 shipping for the new one) and they sent me another.
oh and dont forget to take hspl off your phone before sending it in. its not that hard of a process just make sure you use a 2gb or less sd card when you have to reflash your stock rom on there or else it would not work
How do i take of hardspl?
go to the htc site and get a stock rom, unzip the file with 7zip, find the .nbh file rename to LEOIMG.bh put it on a formatted micro sd card smaller than 8gig bootphone to bootloader and let it do its thing
oops my bad thanks amidniteload
Demon_man said:
go to the htc site and get a stock rom, unzip the file with 7zip, find the .nbh file rename to LEOIMG.bh put it on a formatted micro sd card smaller than 8gig bootphone to bootloader and let it do its thing
Click to expand...
Click to collapse
LEOIMG.nbh not bh
Sent from my HTC HD2 using XDA Premium App
so this wo`nt solve the problem...just sort of appear as normal wm 65 phone?
is77gal said:
so this wo`nt solve the problem...just sort of appear as normal wm 65 phone?
Click to expand...
Click to collapse
Hi,
This process will restore your phone to its original condition.
There will be NO trace of any modding.
You can then send it to be fixed under warranty.
the warranty has expired i was interested in trading it for smthg else...so i was interested in it working
solved it using http://forum.xda-developers.com/showthread.php?t=803242&highlight=screen+freeze and reflash android....lets see how it evolves now...thanks all for the quick replies
Nope...it worked for a day( ))
is77gal said:
Nope...it worked for a day( ))
Click to expand...
Click to collapse
only one day?
i didnt get clearly, is your phone screen is off? of show the desk but you touch the screen there is no response? from which part? which ROM are you using ?
first , you dont have to worry too much cause on that site, you have sloved your problem but not more than one day. so the problem is not about you hardware.
why not change a new ROM?
FYI. do not use the OFF button(on the right, first one) too much, cause HD2’s screen cable is under the off button.
try to download soft button of widget instead of the hard one.
you may look at my phone screen. on the right at the bottom. (LOCHMYDRO sth..)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The problem is obviously software problem...I'm using coredroid the latest release from their site...I'll try reflashing to wm but how large does the sd card have to be....i have one bigger than 2 gb and one of just a few mb...is there a minimum requiered?
Hello
My girlfriend borrowed her dads HD2, and now it stopped working. She talked to him and most likely it requires an update of Android.
I'm usually pretty tech-savvy, but the language spoken on this forum is beyond my comprehension.
So, I have a HD2 with both win & Android installed. To boot into Android i need to go into windows and press two files on the SD-card: "CLRCAD" & "HARET".
The files look like this in Windows (pc):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Her dad mentioned Boxmax 6.5, so I found this thread:
http://forum.xda-developers.com/showthread.php?t=1100560
The files I downloaded from there looks pretty similar, aside from a few additions on the phone.
Downloaded the SD-one, but now i'm lost.
How do I update the phone? Just overwrite the files with the new ones or clean install? If it's a clean install, how do i do it? Do i need to backup something?
Backup all files on the SD card to a safe place (pc).
Delete folder Android on the card.
Copy the Android folder from the archive you downloaded.
Pop the SD card back into HD2, and start Android from winMo (clrcad, haret) or better yet install the exceller autoboot.
Thanks alot, sounds easy enough
When i pop the things back on the SD-card from the backup-folder, I still need to install all the apps and widgets again right?
Edit: Oh, and what about all her messages? Are they stored on the phone?
bolbronx said:
Thanks alot, sounds easy enough
When i pop the things back on the SD-card from the backup-folder, I still need to install all the apps and widgets again right?
Click to expand...
Click to collapse
Yeah, you usually use titanium backup, heh.
sent from my phone using my fingers
Thanks so far for all the help, I got it working fine except, and this might be a really n00bish question, how do I turn off the phone?
Nevermind, found Quickboot
So here is the New Rom for your Huawei U8650.
The Rom was tested for 3 weeks and so far has no bugs, the rom is fast and stable, it's based on 2.3.5 Huawei rom, with OC kernel up to 780MHz, it also have app2sd.
I has 360 launcher added so thanks to the original uploader
I assume that everybody knows how to root and custom recovery the U8650 if not just search my other post.
Note: YOU FLASH AT YOUR OWN RISK. I'M NOT RESPONSABLE FOR ANY DAMAGE TO YOUR DEVICE.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
How To Install:
1) Boot in recovery
2) Wipe data/cache/dalvik
3) Partition SD 128 Ext and 64 Swap (Partitioning SD erase data on SD, so BACKUP)
LINK:
http://www.mediafire.com/?texsqsoa9pa4vp2
If you like my work buy me a beer
Not for me
Unfortunately when I try this on my U8650, I get
Code:
E:signature verification failed.
What am I doing wrong ?
qong said:
Unfortunately when I try this on my U8650, I get
Code:
E:signature verification failed.
What am I doing wrong ?
Click to expand...
Click to collapse
What recovery do you use???
Thanks for your response.
I'm a complete newbie.
I'm not sure, how do I find out ?
All I did was install the standard ROM by downloading it, copy it to the sd card and restarting whilst pressing Vol+, Vol- & the power button on my U8650.
Then I rooted it by restarting whilst holding down Vol+ & Power and then selecting the root.zip.
After that I tried the same with your zip !!
That's all I've done since I've had the phone.
OK, not so much of a newbie anymore.
Managed to install a CWM and then your ROM
Seems a bit slower. But it's beautiful.
Xiexie ni
Volume
how increase volume like cyanogenMod
Weather widget
How can I change the weather widget to a european city ?
When I try to change the location, it only seems to recognize chinese.
Problem with mobile networking
Hello i have encountered only 1 problem with your rom (or is it my mistake?) and it's about mobile internet.I can't get it to function ... It can find all available and says it has registered on the one I want but then there's no internet...some1 pls help
Hi,
I had a similar problem.
Eventually, I figured out that I had to manually add the APN.
This is done in
Setting - Wireless & Networks - Mobile networks - Access Point Names
Hope this helps.
damn i knew it was about that..but idk how to set up an APN i'm kinda new to all this(tele2 croatia)
nvm i did it ty ery much