Related
Last friday the battery of Qtek 9100 over totally. I was without the charger and USB cable to charge de battery. I charge the cell only in friday night. But any led turn on and the cell phone doesn´t turn on too. I put many hours to charge, but the cell phone still doesn´t turn. What can I do to fix it?
FredyOliva said:
Last friday the battery of Qtek 9100 over totally. I was without the charger and USB cable to charge de battery. I charge the cell only in friday night. But any led turn on and the cell phone doesn´t turn on too. I put many hours to charge, but the cell phone still doesn´t turn. What can I do to fix it?
Click to expand...
Click to collapse
The retention charge of the battery shudn't go below 20%,it seems that the battery has fully diffused of charge,it won't charge with usb cable and pc,cuz its charge output is only 0.5 amp.It'll only charge with the wall charger with an output charge of 1.00 amp.Get it charged with a 'Wall Charger',hope it'll work out,otherwise,you might have to try the "Jump Start" trick.Take a usb to mini usb cable and cut the mini end off. Strip the black and red wires, plug it into your laptop or desktop usb port and touch the black to the negative terminal of your battery and the red to the positive. Hold them in place for about 20-30 seconds, place the battery back in the phone and it should boot and then charge normally. Somewhere on this site you will find this information and a couple of posts from people who used basically the same technique with a nine volt battery,where,a wall charger is cut off in the same way and "Jump Start".
Good luck !
My friend, you are simple the best. You are my hero. I lost one USB cable, but my phone come back. Your "Jump Start" trick worked perfecty. Really thanks about your tip. I don´t have words to glad you.
zabardast_1 said:
The retention charge of the battery shudn't go below 20%,it seems that the battery has fully diffused of charge,it won't charge with usb cable and pc,cuz its charge output is only 0.5 amp.It'll only charge with the wall charger with an output charge of 1.00 amp.Get it charged with a 'Wall Charger',hope it'll work out,otherwise,you might have to try the "Jump Start" trick.Take a usb to mini usb cable and cut the mini end off. Strip the black and red wires, plug it into your laptop or desktop usb port and touch the black to the negative terminal of your battery and the red to the positive. Hold them in place for about 20-30 seconds, place the battery back in the phone and it should boot and then charge normally. Somewhere on this site you will find this information and a couple of posts from people who used basically the same technique with a nine volt battery,where,a wall charger is cut off in the same way and "Jump Start".
Good luck !
Click to expand...
Click to collapse
Thanks !
really glade you have it up and running
Have a nice day !
zabardast_1 said:
Thanks !
really glade you have it up and running
Have a nice day !
Click to expand...
Click to collapse
I'd like to know if is it possible update ROM by RUU with Windows Vista? I download a ROM S.N.N_ver._2.0 and tried update, but gone a error when the process will begin. Is there a way to fix?
FredyOliva said:
I'd like to know if is it possible update ROM by RUU with Windows Vista? I download a ROM S.N.N_ver._2.0 and tried update, but gone a error when the process will begin. Is there a way to fix?
Click to expand...
Click to collapse
Its much easier and trouble free to flash with WinXP and its recommended highly,as winVista still has some compatibility problems.So I advise you to flash with winXp OS.
But some people have successfully flashed through winVista,you need to download some drivers.check out this link,there are complete instructions for flashing with winVista :-
http://www.anichillus.net/index.php?topic=21.0
Cheers!
zabardast_1 said:
Its much easier and trouble free to flash with WinXP and its recommended highly,as winVista still has some compatibility problems.So I advise you to flash with winXp OS.
But some people have successfully flashed through winVista,you need to download some drivers.check out this link,there are complete instructions for flashing with winVista :-
http://www.anichillus.net/index.php?topic=21.0
Cheers!
Click to expand...
Click to collapse
Thanks one more time and sorry to annoying you...
I LOVE YOU !!!
Thanks more than a lot
Jump start trick worked fine for me too !! I cut the wire off from old usb mouse and use it as informed.
I just cant understand how it could be so that if you let the battery power too low or empty the wall charger (5v/1A) will not begin to charge it again ???
But my battery is alive again and I m happy, thank you !
jagr55 said:
I just cant understand how it could be so that if you let the battery power too low or empty the wall charger (5v/1A) will not begin to charge it again ???
Click to expand...
Click to collapse
It's just a design flaw. Sometimes things get by engineers. They're too busy trying to create an interesting user experience, and they forget to cross t's and dot i's.
This worked for me as well!!!
Thank you so much, dude... helped me resurrect my Wizard who'se been dead for like 3 months now!!!
iceblade911 said:
This worked for me as well!!!
Thank you so much, dude... helped me resurrect my Wizard who'se been dead for like 3 months now!!!
Click to expand...
Click to collapse
Thanks you all,it was grrrrr8 to hear you all got your phones working again.
Have a nice day !
my qtek 9100 freezes at startup after jump starting.
I jump started my Qtek 9100 and it started up as normal but it freezes at the windows mobile loading screen and doesnt go any further. Does this mean its charging or is the battery completely dead or something?
Wow, it like totally worked but Then I let it charge but battery stays at 0%
Thanks for this thread.
My word am I happy ...
Worked like a charm...
You are my hero! mi Qtek is alive again, i bought a cheap wall charger for a V3 Motorola and it can charge my Qtek after a battery drain off, i tray a lot of things but the usb wire cut off solve my problem and im happy again, thanks a lot and greetings from mexico! Saludos!!
Thanks man it was worked for me,
I was trying to put windows mobile 6 but after that mu camera and voice call buttons doesn't work
If you know more about win mobile 6 on wizard pls help me
Thanks
please do not use stripped USB cable or 9V battery to resurrect wizard. the battery is rated 3.6-3.7V (?? cant remember)... use 3x AA(A) batteries or other 3-4V power supply. I've done this with old pc PSU which has 3.3V output.
Just put battery in, connect charger, connect + - cables while inside wizard - bootup - when windows is loaded device can charge itself - disconnect resurrection power supply.
do not try to charge li-ion battery with whatever currents/voltages... or at least wear some kind of fire protection
Hi Guys
I have a problem with my TyTN at the moment.
My device is not charging.
Yesterday i put it in my Docking Station and wait a little time.
But Now the Tynt isnt charged.
I think ist a Problem with my TyTN Hardware.
I have all Power Supplys used they i have, but it doesent work.
Can you help me?
Its this a problem with the accu or a fuse on the circuit ?
Sorry for my broken english i hope you understand me.
Regards Patrik Laube
Hello,
first of all, try to soft reset the device.
If it fails, hard reset it.
If it doesn't work, go the service center.
Good luck
The above advice is fine. But you did not say if any of the LEDs are lit.
Do you get the red NO CHARGE LED?
Does your phone operate normally except for not charging?
Mike
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
I had a similar problem, which was sorted by a new rom, but I ascertained it was software problem when I realised it charged when powered off.
PatrikLaube said:
Hello
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
I'm having an issue along these lines, also.
My phone has been working fine untill the other night when I tried to charge it via the wall electrical outlet. It will not charge at all, the battery has been drained to nothing and I can't turn it on. The yellowish light doesn't turn on when I plug it in like it used to.
I don't know if this is a battery issue or an issue with the USB connection inside of the phone. On a side note, when it did have power and I tried to connect it to the USB via the PC; it didn't work. The phone was on, but the computer didn't even notice the phone was plugged in. That leads me to believe it would be a connection issue; but I'm not quite sure.
If anyone has anything they can add to this I would appreciate it, thank you.
P.S. Bringing it to a service center is a bit out of the question in the mean time seeing as it was bought on eBay and funds are limited for the time-being.
MiZi666 said:
hi,
try this: when your device is connected via usb, tab on the battery icon in the taskbar on you device, go to the register "advanced" and check/uncheck "When Device is turned on, do not charge the battery when connected to the pc"
thats it
greetz
mizi
Click to expand...
Click to collapse
Hello, I cannot find the "When Device is turned on, do not charge the battery when connected to the pc" in my device. My Rom is WM6.1 CE OS 5.2.20273 cooked by dvha79_ddt.
My HTC TyTN has the sample problem, but i can use the USB to charge normally. It cannot work using my AC adapter Only when the device is open...
About your Battery Issue.
I'll tell you exactly why ur phone isnt charging anymore... If you have been charging it alot on the USB or pretty much any!! charging on the USB u have killed ur battery, never charge your phone on the USB it kinda sucks they should make these phones able to be Sync'd thru USB without a battery cause these batteries should not be powered thru the USB over Time... from syncing to your pc will kill these batteries i have noticed that when u sync this Tytn Ithru USB and the device is at say 70% it charges up to 100% pretty fast i would recommand to you and anyone who reads this dont sync your TYTN or any HTCC phone for to long to the USB Cause it will Trash your batteries Life down the road... Hope this was HELPFUL.
Cheers
Paul
PatrikLaube said:
Hello
My Phone is working fine but i cant charge it with the original HTC adapter.
I must load the accu with a special loader.
USB and Charge dont work....
And i have no warranty I cant send it to my operator.
When i plug in the USB Cable it doesent make everthing.
I think it was a to high voltage on the USB or the USB Ground ( - ) had a electrical Power for a litte moment.
Have you an idea?
Thanks for yur help.
Regards Patrik
Click to expand...
Click to collapse
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
does anyone has a solution to this ?
hi, did anyone solve this problem ? ive got the same problem with my htc touch cruise, i think it charges when turned off but doesnt when on. the orange light doesnt turn on when i plug usb to charge it and it doesnt sync thru the PC neither.
Does anyone has a solution to this ?Thanks a lot!
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
gypsygirl13 said:
^I'm having the same problem with my herm200. I did the soft reset, hard reset changed ROMs but still the same problem. I don't think it's the usb connector because if it is it wouldn't have been able to charge the phone even if it's turned off. Before I'm able to charge it turned on but it would take a few minutes before the orange led turns on, but when I use the phone or if I receive a text the orange led would turn off it's like the charger disconnects but after a few minutes it would go back again. Now it just wouldn't charge turned on, sometimes it gets worse where it just wouldn't charge on or off.
Now I'm already planning to buy an external battery charger.
Click to expand...
Click to collapse
Are you using an official 1000mA charger? (Not a 500mA one) 500mA ones work, but they are under-powered and can cause strange behaviour, like not charging whilst turned on or whilst on a call. Similar problems can be found with car-chargers that will not charge until the device is soft reset.
Mike
^no it's not the official charger, I have this usb wall charger called Power Juice (phone and mp3 charger).
Input Voltage: AC100-240V
Output Voltage: 5V
Output Current:1000mAh
Do you think it's because I'm not using the original charger?
fixed my charging problems
The boyfriend told me to try a new cable for my charger so he bought me a 5pin usb cable, tried it at home and it worked! I still need to turn off the screen sometimes but that's ok at least I don't have to turn off the phone anymore. Now my battery charges less than 3 hours.
Hold both SoftKeys and Then press the Power button
Or you can also hold both softkeys and then put your stylus into the reset hole.
answer why it does not charge through the usb
Sorry for the very very late response. Under electrical legislation all hand held electrical devices must be insulated and fused. Some of the chargers that you can purchase are sealed without fuse which indicates that the phone has a fuse contained within its circuitry (or there may be 2 fuses one in each device) .
The problem you have encountered is that you have connected your phone to a computer or mains supply to charge. There has been a surge in the electrical supply either on connection or by un-connecting from these supplies (e.g. connect to the computer as it is booting would see a 65w signal through the USB) and this more often than not blows the fuse which sits on the PCB (printed circuit board) just after the usb connection internally to the phone.
you can either have the fuse fixed for 20/25 gbp or you can purchase a new circuit board or you can use an external charger for the battery. As it is only the power input point that is faulty.
hope this helps
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
cyberdroxxx said:
Since we are at this non-charging & battery issue, I would like to ask this question on the D838pro. My battery won't charge even after 24 hours of charging. The red LED blinks thru the whole process. The LED did not turn on to orange or green. It is the battery problem because my spare battery works well. I would like to know what is wrong with the battery as I am willing to strip down the battery. Could it be the battery circuit or wiring that had fired?
Click to expand...
Click to collapse
Never tried stripping down a battery, some things... well, just don't seem worth it. However as a learning exercise it might be interesting. Without lots of testing on a good battery with a multimeter then I have no clue what the readings should be between all the contacts. (Now there's a little job for you) It is as likely the internal structure of the battery is screwed as it is to be a wiring problem.
If you solve it you can certainly report back here
Mike
My phones battery if fully dead.. But when i have the charger plugged in it does to the white Htc screen and reboots. I have clk installed so how do i get to charge offline?.. thanks
with cLK 1.3 and newer, just leave the phone plugged to the charger and wait until it's fully or partially charged.
Plug in the USB while the battery is out, and then replace the battery, you should find it starts charging without trying to power on.
samsamuel said:
Plug in the USB while the battery is out, and then replace the battery, you should find it starts charging without trying to power on.
Click to expand...
Click to collapse
thanks a million.. it worked, sorry for the bad spelling glad you understood what i worte
Hi Folks,
My HTC HD2 Android not getting charged either by a wall charger or usb via my pc... i dont what happened suddenly it got turned off due to low battery and when i pluged it for chrging its not showing orange LED notification of charging. when its off and plugged in Orange LED blinked once and Phone got switched on. And when its connected to PC for abt 3 mins it will show charging and after that it shows discharging and battery drains when it shows it discharging . pls help me out coz i dont want to loose my Leo .
Thanx in advance,,,,
Check the pins at the phone which connects to the battery. Sometimes they are deformed and this cause the charging/not charging problem.
But... in this case I don't think this is the problem, because this problem should not affect direct charging from usb cable.
Anyway check them just for sure!
Thanks VDodi
VDodi said:
Check the pins at the phone which connects to the battery. Sometimes they are deformed and this cause the charging/not charging problem.
But... in this case I don't think this is the problem, because this problem should not affect direct charging from usb cable.
Anyway check them just for sure!
Click to expand...
Click to collapse
I tried diff cables but its the same...
Magldr doesn't support charging when phone is off.
Nigeldg said:
Magldr doesn't support charging when phone is off.
Click to expand...
Click to collapse
so if your phone dies how do you get it to charge?
Wdustin1 said:
so if your phone dies how do you get it to charge?
Click to expand...
Click to collapse
Best way is not to let it run out
However, normally it will have enough charge left once it dies to boot up far enough to start charging. If this is not the case, then you have to cut open a USB cable and use the red and black wires to charge the battery. I have not had to do this and am unsure as to how to do it but there are tutorials. It seems simple enough.
Sarathdna said:
Hi My HTC HD2 Android not getting charged either by a wall charger or usb via my pc... i dont what happened suddenly it got turned off due to low battery and when i pluged it for chrging its not showing orange LED notification of charging.
Click to expand...
Click to collapse
Consider, as was previously suggested, a cable connection issue.
While you do not currently have the luxury of looking at your status icons, I have found that, on occasion, when I plugged in the phone to charge, the status icon indicated a USB connection, rather than a charging icon. Unplugging the cable and re-inserting the cable fixed it.
Note that new high quality cables can exhibit the same issue.
You have nothing to lose... Give it a shot.
Good luck.
----
Sent from my ICS HD2 with XDA Premium
Nigeldg said:
I have not had to do this and am unsure as to how to do it but there are tutorials. It seems simple enough.
Click to expand...
Click to collapse
Take out battery, plug chopped up USB cable into wall charger, use fingers to hold red to + black to -, count to twenty, battery in phone, phone into bootloader, real charger cable into phone and wall charger, leave 10 mins, reboot into android. (Can charge all the way in bootloader, but it seems slower than when android is running.)
samsamuel said:
Take out battery, plug chopped up USB cable into wall charger, use fingers to hold red to + black to -, count to twenty, battery in phone, phone into bootloader, real charger cable into phone and wall charger, leave 10 mins, reboot into android. (Can charge all the way in bootloader, but it seems slower than when android is running.)
Click to expand...
Click to collapse
By 'tutorials on how to do this' I basically meant your posts
As previously said if you're using magldr you need to be booted into Android before the phone will charge. You can try to warm the battery up in your hands to squeeze the last bit of power out of it to boot up. Or there are standalone hd2 battery charges you can buy from eBay that charge your battery outside of the phone, they're pretty cheap.
Sent from my HTC HD2 using XDA App
As Samuel said you can charge phone in bootloader. Just try!
Had to buy external charger
item # M00366 this charger was cheap has led's that change from red to blue as the battery charges and has a usb port so you can charge a battery in phone at the same time.
I'd been alternating tween an extended battery and the original when my HD2 started discharging while plugged in. same batteries and nearly a year of typhoon's excellent ROM progression then wham dead batteries....
Hello Experts!
I left my S8 (SM-G950F) overnight for charging, I checked the phone at 5am it was fine when I switched off the Alarm clock and left it again for charging, but when i wake-up it was off and not turning on, i have tried safe mode restart by pressing the volume down + power key for up-to 40 seconds also tried to start into boot / recovery mode by pressing vol up+power+bexby button but it seems nothing happening?
Now when I plug it back to charge nothing on screen, no charging light or any other sign but i feel that the area above the back camera is getting warmer after a while but yet its not powering up when i try to.
I have the Original wall charger and cable, though i have tried another wall charged and another cable and tried to plugged it in the charger for around 10 to 15 mins but yet the same with no luck.
Any help in this regards will be highly appreciated.
Thanks a million in advance.
Regards.
try a wireless charger if you can find/borrow
02xda2 said:
try a wireless charger if you can find/borrow
Click to expand...
Click to collapse
Thanks for your response ... do you think wireless charging will automatically begin if i place it above it in this current state?
also what do you think had happened in my case causing this issue?
waqarhussain22 said:
Thanks for your response ... do you think wireless charging will automatically begin if i place it above it in this current state?
also what do you think had happened in my case causing this issue?
Click to expand...
Click to collapse
Their is a known deep discharge bug you may be suffering from try usb and wireless back and forth tgethor
TheMadScientist said:
Their is a known deep discharge bug you may be suffering from try usb and wireless back and forth tgethor
Click to expand...
Click to collapse
Thank you for your input, I will look for the wireless charger and will try to charge using wireless charger, But yet i have a question, for wireless charger, do I just need to put the phone over the wireless charger and the charging will start itself or do i need to do any other steps when I place it above the wireless charger?
Also, you said to use Wired and Wireless charger both, i have tried two wall chargers with two cables with no luck, so is there anyway i can try with the wall charger for specific time or what??
Also, I just noticed the charger pin which goes into the charging base are the same from both the sides, so is that okay if I plug it upside down as the cable can be plugged from both the sides without any issue, so is that fine or do i have to put the logo side up towards the screen side? and what if thats not the same, do you think plugging it upside down may cause any issue can do any damages to the phone?
Many thanks again for your time and suggestions.
Regards.
Waqar
waqarhussain22 said:
Thank you for your input, I will look for the wireless charger and will try to charge using wireless charger, But yet i have a question, for wireless charger, do I just need to put the phone over the wireless charger and the charging will start itself or do i need to do any other steps when I place it above the wireless charger?
Also, you said to use Wired and Wireless charger both, i have tried two wall chargers with two cables with no luck, so is there anyway i can try with the wall charger for specific time or what??
Also, I just noticed the charger pin which goes into the charging base are the same from both the sides, so is that okay if I plug it upside down as the cable can be plugged from both the sides without any issue, so is that fine or do i have to put the logo side up towards the screen side? and what if thats not the same, do you think plugging it upside down may cause any issue can do any damages to the phone?
Many thanks again for your time and suggestions.
Regards.
Waqar
Click to expand...
Click to collapse
L thCable direction does not matter type c is universal wireless starts automatically. What I have seen work in the past is place it on the wireless charger then plug in usb and leave both plugged together.
You might also try holding the download mode button combo for upto 30 sec maybe it is frozen
volume down power and bixby.
Sometimes Samsung's freeze and need a battery disconnect. Obviously we can't just do that on these.
My kids tab Es do it all the time. Have to separate the screens. So I can disconnect the batteries