I've been having an issue with both the proximity sensor and the light sensor. If I press the phone against my face it'll start pressing numbers or disconnecting calls (screen won't turn off due to the sensor not working) and the light sensor doesn't affect the illumination levels on my screen and buttons; actually the only way to make my buttons light up is manually changing the brightness (both screen and buttons) but after locking the phone and waking it back up the buttons stay unlit.
Has anyone else had this problem? I'm not sure if I've been having it after flashing CM9 or after my phone got a bit wet. I took the phone apart to check if something was wrong with the sensors (obstruction, dirt, corrosion, etc) but couldn't find anything.
Also, I downloaded "Sensors List" from the Play Store and both sensors are not detected.
Any ideas?
Idea...
About button light... Is your display brightness set to Auto? If not, set it to auto and your buttons will be fine.
I just tried doing that and it didn't worked, not even completely removing the screw. I guess the sensors got damaged with water (if they can be damaged that way). Oh, and setting the brightness to Automatic doesn't do anything either.
Thanks a lot though.
Related
I there any settings or something to adjust proximity sensor? I was trying to turn off screen covering sensor with thumb, but.. no effect.
Does it need any setting or my phone is faulty?
I noticed the same thing on my phone today.
The proximity sensor doesn't work if you've switched off the Automatically adjust backlight option in Settings>Sound & Display>Backlight. There doesn't seem to be any way around this as the proximity sensor doesn't have its own option.
Are you in a call? You need to be calling/receiving a call for it to work.
I agree, I think you need to be in a call for the proximity sensor to work properly.
For me it works fine. And i don´t hade automatic backlight on.
aldabal said:
For me it works fine. And i don´t hade automatic backlight on.
Click to expand...
Click to collapse
That's interesting because I can toggle my proximity sensor (whilst in a call) by toggling the automatic backlight. That option must be linked to something else as well.
Screen goes black
I do have the same behavior, when I make a call the phone's screen goes black automatically so if I need to press any key have to press send to get my screen back, then use the keypad, nonsense, is anyone having the same issue ?
for me, the proximity sensor doesn't work at all. I have the automatic backlight setting and yet it still doesn't work. any idea why?
SP300
I just found the solution, I have got the screen protector on "The Original HTC SP300" and is causing the screen to go blank when you do a phone call, If a remove it a little bit from the top left corner and make a call works as spec.
Hello,
I have bought myself a diamond touch 2, and i directly flashed it to Dutty's R6 rom because i like it much better and i made up my mind about it even before i bought it.
Now i seem to have a problem, and i don't know what would be the problem; either the device or the rom?
Proximity doesn't work; setting automatic backlight dimms the screen to a low-light level. Holding a flashlight above it doesn't make any difference.
Also, when making a call, the display keeps being illuminated the whole time, no matter if i hold it to my ear or not.
Does someone recognize this problem?
Cheerz
Exca said:
Hello,
I have bought myself a diamond touch 2, and i directly flashed it to Dutty's R6 rom because i like it much better and i made up my mind about it even before i bought it.
Now i seem to have a problem, and i don't know what would be the problem; either the device or the rom?
Proximity doesn't work; setting automatic backlight dimms the screen to a low-light level. Holding a flashlight above it doesn't make any difference.
Also, when making a call, the display keeps being illuminated the whole time, no matter if i hold it to my ear or not.
Does someone recognize this problem?
Cheerz
Click to expand...
Click to collapse
Settings\System\Power\Backlight\ Turn off Auto adjust.
If i turn off auto adjust i can indeed set full brightness, but that's not the point. I want the auto-dimming and proximity sensor to work, so when i hold the piece next to my ear it locks and turns off the screen...
If I turn on auto-adjust, it doesn't respond on any lightchange or action; it just dimms the screen to about 40% and keeps it there.. either a bug or a hardware fault with my unit?
Not sure that it ever worked perfect out of the box.
Have you tried tweaking the settings with TD2 Tools?
How do you mean tools? As far as i know i can only find one box to turn auto adjust on.. you have the same configuration, does it work for you?
EDIT: I installed the app "LumosWizard". Now the phone's backlight adjusts depending on the light the sensor receives. The sensor works well as the values go up when putting a flashlight on it.
However, i wonder why this doesn't work with just auto-adjust on, that's what the HTC Auto-Backlight should do right? Also, with this app, the backlight doesn't go out when no light is reveived (auto-lock when putting into pants, or turned off backlight when calling...) ?
This is what i'm looking for: http://www.youtube.com/watch?v=6xakUmz1zwc
=> i don't think this is achieved by an additional application, but is just standard HTC service doing this because of putting on the auto-adjust...
There is NO proximity sensor on Touch DIAMOND II. Only light sensor. Use Touch_InCall_Screen_Tweak instead. This program use G-sensor and block the screen when your phone is in vertical position.
m72m72 said:
There is NO proximity sensor on Touch DIAMOND II. Only light sensor. Use Touch_InCall_Screen_Tweak instead. This program use G-sensor and block the screen when your phone is in vertical position.
Click to expand...
Click to collapse
Thanks, installed and works good!
Still wondering though why i need a 3rd app like LumosWizard to make the lightsensor work, as htc's autoadjust apparently doesn't
I did find this .cab called Glight and it works great on my TD2
More about it here:
http://www.ageye.de/index.php?s=glight/about
According to the Leo/Linux status wiki (http://htc-linux.org/wiki/index.php?title=Leo/Status) the Ambient Light Sensor is still not working properly.
That would explain why auto backlight adjustment does not work.
However, when in the phone screen the light sensor seems to work in that the screen goes dark when I cover the light sensor, as expected.
So I am curious as to the status of this regarding auto backlight specifically, does anyone have any more concrete info?
Perhaps there are separate light sensors? Or perhaps the light sensor only works in a limited fashion for the time being?
Just curious, not complaining
(P.S. the free "Battery Level" widget from the Market has worked well for me in the absence of auto backlight adjustment, in case others find it useful)
well there's a proximity sensor on the phone that comes into play while you are in an active call. it disables the back as you put the phone to your ear. you were simply simulating that action by covering the sensor with your hand.
Ah ok! Thats what the proximity sensor is. That is indeed marked as working on the status wiki, so that makes sense.
Thanks!
Just as the title says-
I am not able to locate the light ambient sensor on my A500 tab- My previous A500 got replaced by acer because the speakers were defective in some way-
I have read that the light sensor is located below the volume rocker and rotation switch on the black glass and can be seen under bright light- i tried every way to find it no success.
I tried "proximityscreenoff" and "sensorlist" from the market. Both of the freewares listed an ambient light sensor on my device as -"Lite-on al3000a Ambient Light sensor"-
BOTH THE APPS COULD NOT GET ANY DATA FROM THE SENSORS :O-
DO we even have a sensor? or is it just me without it?
Can someone please use the apps and tell me if any data is being collected from the sensors?
Highly appreciated- thanks you
I tried with Sensor List and it does indeed show up the sensor, but doesn't seem to be getting any data from it. So it's not just your tablet.
Same thing with "AndroSensor", it shows it but no data change in it either. Hopefully we can figure out what the issues is? Are both of you using the factory install rom? Or a rooted one with a tweaked kernel?
sda.171 said:
Just as the title says-
I am not able to locate the light ambient sensor on my A500 tab- My previous A500 got replaced by acer because the speakers were defective in some way-
I have read that the light sensor is located below the volume rocker and rotation switch on the black glass and can be seen under bright light- i tried every way to find it no success.
I tried "proximityscreenoff" and "sensorlist" from the market. Both of the freewares listed an ambient light sensor on my device as -"Lite-on al3000a Ambient Light sensor"-
BOTH THE APPS COULD NOT GET ANY DATA FROM THE SENSORS :O-
DO we even have a sensor? or is it just me without it?
Can someone please use the apps and tell me if any data is being collected from the sensors?
Highly appreciated- thanks you
Click to expand...
Click to collapse
I got Sensorlist and tried it and I do get data from it.
xhz/xxxx or xxxxxms and a red line. The upper limit is 227 and lower limit is -227 and the red checked number changes. It's nowhere as quickscrolling as the other sensors but I get a jagged red line moving across.
okay guyz i think i figured this whole thing out most probably-
I just came back from this electronic store, i closely examined the iconia on display- a500 - noticed the black glass under the volume rocker and rotation lock and THE LIGHT SENSOR WAS THERE! :O - looking like just any ordinary light sensor-
This made me come up to the following conclusions- since i have had another iconia before i returned it for warranty- i was able to identify the following differences-
1st variant-model
Light sensor present
Mic volume low
Volume locker button hard to push
Power button sorta pushed inside
2nd variant model -( the one i currently have)
Light sensor absent? Or hidden under black glass? (Manufacturing defect?)
Loose rotation lock (hardware) toggle
Mic volume high (as in proper)
-(i faced these additional problems)-> glass over the camera came off and the glossy label on the side slipped out.
So if u have the first variant, the one i previously had and the one i examined in the shop today- that should give u data from the light sensor, and the 2nd variant with hidden/absent light sensor won`t.
These are my findings. Feel free to point out and discuss-
What should we do? I m considering a second replacement now -_____-
With AndroSensor app open, try to put some direct light above the sensor and see if it shows some readings. I noticed that the sensor is in a sort of sleep status until it sees some light; after then it kinda wakes up and works properly.
I appear to have what you call the second variant model. I just checked with Androsensor, and the light sensor does appear to be present beneath the black glass, just under the volume up rocker. I agree it does appear to sleep until it senses a light source.
cm0901 said:
With AndroSensor app open, try to put some direct light above the sensor and see if it shows some readings. I noticed that the sensor is in a sort of sleep status until it sees some light; after then it kinda wakes up and works properly.
Click to expand...
Click to collapse
I just downloaded andro sensor-
Under light sensor it sed-waiting for event-
I took my hd2, turned on the flash! Pointed it right above the sensor and no response, it just kept saying waiting for event- so does this mean i have a defective sensor?
Can this be a kernel/rom related issue?
Pls someone try this and let us all noe.
Thanks
It's a long shot but you might attempt flipping the check mark a few times under the brightness setting and "auto adjust" as that probably toggles the sensor as well, though these apps are supposed to do it. Or close and start the app a few times and then check the sensor. I don't know what activates it but I can confirm that it has some kind of threshold where it sleeps or isn't active and another where it is, so you might want to try various things to, as others have mentioned, wake it up.
Are you using any ROMS by any chance or are you on stock? Have you done any sort of modification of the system - rooted and removed things or replaced kernels, etc?
If you are on a ROM or have done any modifications, you may want to try going back to full stock 3.2 or 3.1 and seeing if that helps before you decide it's actually defective.
Just double checked mine running a 3.2 rooted with thor's kernel. The sensor is working fine. But i did have to uncheck the box for the auto screen brightness to wake it up. Then i used a led maglight on the senor.
Readings from Androsensor:
Light (0.5mA)
55.0 lux
With the maglight cut on it.
65790.0 lux.
Please note with the maglight cut on you can see the light sensor hole then.
KILLER_K said:
Just double checked mine running a 3.2 rooted with thor's kernel. The sensor is working fine. But i did have to uncheck the box for the auto screen brightness to wake it up. Then i used a led maglight on the senor.
Readings from Androsensor:
Light (0.5mA)
55.0 lux
With the maglight cut on it.
65790.0 lux.
Please note with the maglight cut on you can see the light sensor hole then.
Click to expand...
Click to collapse
Same as Killer, seems to be working, rooted 3.2, couldnt see until bright light on it.
Anyone have any idea where the mic(s) are, not really important just wanna know which end to scream into when doing voice search
Mic is located directly in the top center of the front face, in the space between the glass and the bezel. You should be able to see it with just a small amount of light shining on it.
FINALLY!
after various non stop auto brightness toggle on and offs - waiting for event went and 1 lux came xD - i shone light the reading increased - and stopped working agen :|
I dunnu maybe the apps are not fully compatible.
I can say it is working because i changed my brightness to full manually and then turned auto on and the brightness level set itself automatically.
So will we have to wake up the sensor from a state of sleep all the time or is it just for the apps xP - last confusion.
Thanks every1 for ur responses, the mystery is finally coming to an end xD!
W8 user here.
Recently, I returned to stock after flashing 102938123 different ROMs, some CM, some TW.
I've noticed that my prox sensor is not turning off the screen during calls. yes, i've ensured that the option is checked in the call settings.
*#0*#, prox sensor values max out when the sensor is covered, HOWEVER, no green screen, no vibration.
every prox sensor post i've found mentions that the screen turns off during calls, but not back on. "maybe it's dust", they say. not in this case - sensor values tell a different story.
anyone have any idea what could be the cause of the "no green screen, no vibration" issue? i'm 99.9% positive it's also the cause of the "not turning off during calls" issue too.