after my phone rebooted once the update was complete, it wont get passed the "at&T World Phone" white screen... SOMEONE PLEASE HELP ME!!!! i was using a stock at&t pure with the stock rom. i can not upgrade hardspl or ANYTHING any suggestions on how to get my phone to boot? hard-reset went through with no signs of failure but it still will not boot up after that finishes... sorry if its something im overlQQKing, but i just cant figure it out. n yes i have researched although obviously not enough at this point. Thanks to anyone who can help in advance. forgive my stupidity!!!
......
noone?????
The HTC Pure updates hosed my phone too, I had already applied hard-spl to my Pure and i've flashed it with dozens of roms. Since I was currently using one of the "Stock" AT&T roms posted on XDA I figured I could apply the updates. Unfortunately after applying the update my phone froze at the boot loader. I was forced to flash my rom using the memory card method and then restore a backup.
you could try putting the phone in SSPL mode manually, (reset button+volume down), the run hard-spl hard-spl in manual mode.
you can then flash your rom using the memory card method. (FAT32 formated memory card, rom file renamed to topaz.nbh copied to root of flash card, reset button+volume down to enter SSPL, power button to confirm flash).
All this assumes you've already tried to hard reset your Pure (reset button+vol up+vol down)
Thanks for the reply! Unfortunatly, i tried the manual method and after it hanging at 0% for about 5 minutes, i keep getting error [262] update error.. (communications error) is this becuase i can not sync with mobile device center (win7)? I really dont want to just have to toss the phone! I have had an at&t tilt, at&t fuze, and now the at&t pure, and this is the only phone i have had this problem with for some reason...
Try Unplugging Your Pure From the computer Take Out the Battery Put the Battery Back in Mean While Restart your computer and Press Power And Volume Down At the Same time on your Pure If its on the colored screen your good,..Make sure your system is online and your not downloading anything and plug in your Pure to the computer it give it about 2 minutes to download the HTC USB driver then once its done your phone will say USB on the bottom of the Red Green Blue And White four color screen Then open up one of your ROM's and Flash it,....Do You Have Windows Mobile Device Center Installed?
If Not here is the Link
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
If you do already you need to uninstall the Driver update for windows mobile media center then install it again .
i can get the bootloader screen just fine! i just can not get hardspl to flash onto it. it sits at 0% every time. the phone will not boot so i can NOT get into mobile device center. The tri-colored screen comes up with no problem and it says USB on the bottom, so the drivers are already installed. I even tried hard-reset and still no luck
There was an additional cab file I needed to install to HSPL the Pure
"enablerapinew.cab"
basically the machine just would fail to load the HSPL without it
but it still functioned afterwards, does yours?
Do a search on XDA find and DL the cab (or I could attach a zipped copy)
If you can still access the device,
just copy enablerapinew.cab to any temp dir on the device
the execute it through fileexplorer
then go back to installing the HSPL (mine then worked fine)
If you haven't already, You should go to
http://forum.xda-developers.com/showthread.php?t=520312
you'll find troubleshooting info and a link to the extra cab there
If you really are bricked at this point , it sounds like nothing has actually
been changed on your device yet? its just frozen should be still under warrentee? Unless anyone else has a better suggestion you should be
able to return it for exchange to ATT
Good Luck
KJL
It sounds like Windows is not properly recognizing your device when it is plugged into the USB port while in SSPL mode.
Have you tried different ports?
Is there another computer you can use?
another thought about returning under warranty
on the boot page of the stock Pure it indicates HSPL 1.83.000
After you update the HSPL it will say HSPL "1.83.Olinex"
this normally an indication of a successful update,
but it will probably void your warranty if they just look at the boot screen
This is true for all Pure (and Tmobile Compact V) Rom upgrades
The Stock Pure came with 6.5 and therefore the 1.83.00 HSPL
The Diamond2s did not, so their solution which reverts to 1.63 <?>
will not correctly revert to 1.83.00 on the Pure.
No way to correct this yet as far as I know,?
All the "reverts" are geared toward the Diamond2s, not the Pure.
But If your boot screen indicates 1.83.00 before it freezes
I'm fairly sure its still entitled to a warranty repair/replace
How could they tell the cause of the failure
was a reburn as opposed to natural causes?
Good Luck
KJL
When you put the phone into a manual bootloader mode... Mobile Device Center becomes obsolete.
HardSPL is only needed for unofficial roms. Forget HardSPL for the time being. The goal here is to get your phone operational. Just download the official HTC WM6.5 WWE rom and flash that. Put phone in manual bootloader mode and run the Rom installer.
As long as your phone is in bootloader mode and says "USB"... then your set to go.
Another solution is to try another PC. You'd be surprised how often that will resolve your issues. Perhaps find an XP machine and install Activesync (so it loads the bootloader USB drivers). I had to do that on several occasions when my main PC refused to flash my mobile device.
I did both of the updates htc has for the pure. Both worked fine. I am on the origianal rom. It does reboot your phone and stays on the white screen for a min then it loads the update and the phone starts.
The offical ROM comes back with a wrong vender ID error I guess cause its a "pure" and not the HTC branded "topaz"... NOW what should i do??? Seems like i NEED hardspl so i can flash any ROM, as from what i researched, there IS NO AT&T Pure rom that has been released. I still cant figure out why a hard-reset will not work though.... This is REALLY starting to get me angry!!!
Just for reference, the Pure's ID is TOPA210 32M
SPL-1.83.0000
The official hotfixes worked fine for me as well. Did you apply the hotfixes on the original ROM that came with your Pure?
Also, does the official HTC Touch Diamond 2 ROM work for you? If so, the hotfixes for the Pure are irrelevant, as are any future updates released for the Pure. You should look for updates for the Touch Diamond 2 on the Worldwide HTC site.
If you needed to do a warranty claim, the closest you can get to returning your phone to stock/shipped form is to use the ROM dump using HardSPL and hope they don't notice that the SPL is different. Currently, there's no way to return the Pure back to completely official software.
A hard reset simply wipes everything off and restores everything back to what is contained in just the ROM you currently have on it. If you've flashed your phone at all, you've already wiped out the original ROM that came with it.
It is still the STOCK ROM. I have never flashed it yet.. The topaz rom will not flash due to a vender ID error. The spl is still stock also... i think thats is why i am having this problem. I bought the phone off craigslist so returning it to AT&T is NOT an option either way. My only solution is to find a fix. (or trash it) I really appreciate all of your suggestions and input so far. You guys are by far the best board around! I am a LONG time follower, but a few-time poster. Obviously i have little to contribute to the board.
Can I trouble you to dig up a few version numbers? It'd help evaluate your situation so we can see which options are best for your case.
ROM version? You can find this in Device Information. Start --> Settings --> System --> Device Information
Bootloader version? Do a soft reset while holding down the volume down button on the side until a screen with red, green, blue, and white, ordered top to bottom, shows up. It should be the second line starting with "SPL-..."
The ROM is the STOCK AT&T ROM (again...) I CAN NOT go to start;.... because if you noticed in the first post, the phone will not boot past the white "AT&T WorldPhone" screen... the spl is stock also incase you missed that part. (1.33.0000) I have never flashed the divice. EVERYTHING IS HOW AT&T SELLS THE PURE OUT OF THE BOX! NO MODS. NO FLASHED ROMS. NO HardSPL... NOTHING! STOCK!!! (for those overlooking the details in my previous posts) I have no doubt you guys (n hopefully a few girls ) will help me fix my issue. I'm just REALLY anxious for it to happen sooner than later!
Have you tried downloading the official rom here on xda and renaming it to TOPAIMG.nbh and update using the sd card method?
Here is the thread:
http://forum.xda-developers.com/showthread.php?t=600339
The download is in post #1
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
You can flash hard SPL the same way by renaming the .nbh file to
TOPAIMG.nbh
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
Actually that is supposed to be an officially signed rom. If that is true it will work with the stock spl. It will either work or it won't. Also, as stated in the response after yours, you can apply the hardspl via SD as well.
hi guys i need ur help
i flashed full 2.3.4 spf on my defy
i didnt like it so i downgraded it using this guide
http://forum.xda-developers.com/showpost.php?p=14762402&postcount=143
i have followed the steps one by one and every thing worked just fine
now im on froyo that camed with the guide
but every time i try to flash spf using rsd lite it says finished 100% then pass
and my phone dosent but up
no screen no power and i cant accsess to recovery mode or boot mood
but when i log in the boot mood the rsd lite see it but my phone screens still off
any ways i have flashed to eclair that came with the guide and my phone is working again
i have tried to flash another spf the same a black screen with no power
now im back with that fixed eclair that came with the guide
any one can help me and tell me why i keep getting black screen when ever i flash
any one can help me please ?
thanks in advance
I think that is because you flashed a level 5 sbf so you can flash a full sbf with level greater or equal than 5
Motorola Defy CM7 RC 1.5 OC 1GHz
Easy thing first, wipe. Check motto drivers and check if you are installing correct sbf. when it says pass, don't unplug phone. Wait for it to restart itself then wipe again
Got a Headache? It's all in your Head.
You flashed full 2.3.4 sbf which contains CG31.smg and CG39.smg ver=5
from now on you are stuck with limited options of downgrade. There is no possible way to flash a sbf which contains CG ver less than 5 now. "downgrade" to you now means you will have to restore nandroid and then flash fixed sbf which has had CG31 and CG39 replaced with those two Code Groups from one which is of ver=5. I'm not sure, but "maybe" you can flash any sbf you like and then flash fixed sbf from that sbf with these two code groups replaced with one containg CG=5
There's a Eclair (2.1) Chinese SBF with CG level 5. Use that, root, install 2ndinit, flash a fixed SBF.
Don't use the camera flash though!
Good idea!
But the fact remains that he is always stuck with CG31 and CG39 at level 5. Regardless of how he downgrades this will never change. As far as warranty purposes it will never be possible unless his region officially releases a system containing these two CG's at level 5. It is nice though to be able to "downgrade" and still install custom roms and stock froyo roms and the like but ALL of these will still need a fixed sbf containing level 5 CG31
Follow the steps from this tutorial and you will succeed.
so, I bricked my defy
I was on cm7 7.2 kang, then I flashed the white rabbit and that was ok
after that I accidentaly flashed the miui rom pikachu without a wipe
and was stuck at boot logo...
so I downloaded the 2.2.2 Service Flash Central Europe because nordic was unavailable
now, all I got is the white led on the defy, can't even boot into bootloader
what to do?
what sbf should I use??
please help
Many others with the same problem:
http://forum.xda-developers.com/showthread.php?t=1505109
Can you remember what previous sbf's you flashed?
Normally RDS will detect your phone when you plug it in.
Try to remember witch sbf's you have flashed and flash one with the same bl number.
You can try to download the sbf again and install it from a different pc. If you think you never flashed a gingerbread rom.
For a good link to the CEE sbf:
http://sbf.droid-developers.org/umt...RDNFRYORTCEE_P016_A016_HWp3_Service1FF.sbf.gz
read before you flash
i thought it is near impossible to brick defy as its boot loader is locked ... reading saves a lot of time.
vsvj said:
i thought it is near impossible to brick defy as its boot loader is locked ... reading saves a lot of time.
Click to expand...
Click to collapse
You CAN brick it . If you get a power-out on the exact wrong time f.i.
Or you use a USB-cable with a knick in it...
Best thing is not to flash a rom with a bl version higher than your official released as then you can always claim warranty (If your not over the warranty data of course)
Hi, I'm looking for a sbf file for my Defy (not +, red lens) with a CG version 5 or higher.
It's because I bricked my Defy so I flashed this sbf : JORDN_U3_97.21.51
It's US T-Mobile version so I can't phone in France with Orange. Someone told me it's a CG version 5.
If you have a solution to phone with this version in France, I'm taking it too
Thank you
So your phone is working but you have no signal or what?
ehhm, what do you want to do ???
is your phone booting and ready to go on the home screen? then you don't have to flash any sbf ...
if you can not call due to wrong baseband, there is a tool calles "Defy Baseband Switcher", that changes the Baseband to e.g. france orang version ...
hoped to help you ... and if so, please click "thanks"-button
The ~ same thing
I accidentaly installed the CM9 kernel when i should have installed the CM7 one with ICS. Then i made a nandroid restore of my previous CM7. Than... phone dead. Starting but no CWM no ROM booting.
As i have had CM7 with GB kernel i flashed ( not knowing) an old SBF than didn't booted. I tried the US T-Mobile 2.5.1. It boots, i can root it, install CWM.
But than when i try to install a CM7 nightly ( installed ok) it dies again. Starts but No CWM no Rom booting.
What to do? I don't know what SBF to flash or what method to install?
DJ_Synergy said:
ehhm, what do you want to do ???
is your phone booting and ready to go on the home screen? then you don't have to flash any sbf ...
if you can not call due to wrong baseband, there is a tool calles "Defy Baseband Switcher", that changes the Baseband to e.g. france orang version ...
hoped to help you ... and if so, please click "thanks"-button
Click to expand...
Click to collapse
I tried Defy Baseband Switcher but it doesn't work. Thank you anyway.
SBF
You can download all the SBF's from the Wiki Page( Defy General Thread). But you are in my case. I have a thread opened in the Q&A. That SBF you installed is dreadful. So after 2 nights of searching until 4 am i got smth to work. For the record i didn't install a GB SBF. I wanted a Froyo one. The one that worked for me is this one > http://forum.xda-developers.com/show...1&highlight=cg
Follow the first guide. Go to Recovery Wipe data/cache, reboot with volume up pressed. Enter programming. Flash SBF. It starts in Chinese. Don't worry. On the first screen you see press the button/box (with Chinese writing) in the middle of the screen> select English> then Next> then press Later (as you don't need the MotoBlur crap). Than Root it with Superoneclick, install CWM and flash whatever ROM you like.
Warning: Do not turn the flash on the camera. With the Kernel on this SBF you will burn it. Install another Froyo Kernel with your ROM. Don't know how> ask.
Thank you but your link is dead...
Link update:
http://forum.xda-developers.com/showthread.php?t=1486731&highlight=cg
The one you installed is BL5. You can try the froyo above. Or someone PM'ed a couple o minutes ago with this option for the Eclair SBF:Root, install the cwm. Then wipe data, install kernel don't reboot and install cm7. I tried it and it did not work but maybe it works for you. Also if you don't know how to root the Eclair sbf you must do the following> Flash 2.21 , Run the archive(USB debugging On), let it finish/close by itself, flash the 2.51. Sorry, i can't attach files.. will try later
I'm in this kind of awkward situation...
I flashed this chinese Rom thingi-dingi to upgrade my BL to 6...
Then I installed CM10.
This also was kinda normal.
Yesterday i had a problem and decided to install my old nand backup....
it was, i think, corrupted.
Now i have huge battery problems, like defy wont work when not connected to wall charger...
well long story short, want to try and flash a DACH sbf over it.
But i need one that works...
Tried JRDNEM_U3_3.4.2, but it didnt boot up.
Now I installed this chinese SBF, but dont know if it will boot up...
so is there an official DACH FROYO SBF with BL6?
Its not about the Battery, its broken, but i went back to chinese rom and would just like to have a german stock rom with gapps and stuff...
Dont want to have CM10 until i have new battery, dunno why...