Database Users

[Q] Black screen after green Cyanogen banner

I'm stuck on a friend's nook.
I've flashed mine about 100 times no problem.
I've put cyanogen on two other nooks no problem.
I'm doing something wrong with this one I guess.
I have a bootable CWM micro SD and I can boot to it no problem, I'm trying to flash the latest nightly.
What I did up to now was flash the repartition data and reformat data zips.
Then I formated system, data and cache.
Then I flashed cyanogen.
I got it to load cyanogen one time!
But when I rebooted I could never get it to load again.
Since then I have formatted the boot and flashed a few different boot fix files.
I'm stumped.
When I boot it now it goes to the green Cyanogen mod banner, than a second later it says 'loading' under that, then it goes to a black screen. I have to hold the power button down for 15-20 seconds after that to shut it off.
So I have a nook that I can boot to CWM v3.2.0.1 from a micro SD card.
What steps should I take to get this thing working again?

What I did up to now was flash the repartition data and reformat data zips.
Click to expand...
Click to collapse
That wasn't really necessary with CWR 3.2.0.1. I would say drop a copy of the stock 1.3 ROM on the SD card, boot up and start all over wiping data, system, cache and Davlik and then install the stock .zip. That will get you back to the very beginning. Stock full ROM is here: http://dl.dropbox.com/u/30572895/Nook_Color/update-nc-stock-1.3.zip
Courtesy of Taosaur : http://forum.xda-developers.com/showthread.php?t=914690&page=28

patruns said:
That wasn't really necessary with CWR 3.2.0.1. I would say drop a copy of the stock 1.3 ROM on the SD card, boot up and start all over wiping data, system, cache and Davlik and then install the stock .zip. That will get you back to the very beginning. Stock full ROM is here: http://dl.dropbox.com/u/30572895/Nook_Color/update-nc-stock-1.3.zip
Courtesy of Taosaur : http://forum.xda-developers.com/showthread.php?t=914690&page=28
Click to expand...
Click to collapse
Tried that, Now I get 'Read Forever' then a quarter second of the 'N' screen that is Grey then turns a sort of washed out in orange color for a half second, then a message screen that says: 'Install Failed' over a picture of a nook with a red exclamation mark on the screen and 'Please power OFF and back ON again. If you continue to have issues please contact Customer Support or visit www.nookcolor.com/support' Then the device turns itself off.
I had gotten that screen a couple of times leading up to this. Got rid of it by flashing some boot fix files or something.
Something is wrong with the loader or some boot data or something I don't know about.
Can anyone give a step by step on how to take a Nook down to a clean slate then build it back up so I can boot Cyanogen nightly?
I can Boot off a micro SD into Clockwork Recovery.

Those were the steps I took to restore and deregister a Nook recently before returning it for a replacement. However, I never messed with the partitions. Someone familiar with the partition structure will hopefully chime in.

Bump having the same issues. Just started today.
Mine works if I leave it charging, As soon as I unplug it..it turns off.

CM7 and 1.3 ROM hang ups
patruns said:
That wasn't really necessary with CWR 3.2.0.1. I would say drop a copy of the stock 1.3 ROM on the SD card, boot up and start all over wiping data, system, cache and Davlik and then install the stock .zip. That will get you back to the very beginning. Stock full ROM is here: http://dl.dropbox.com/u/30572895/Nook_Color/update-nc-stock-1.3.zip
Courtesy of Taosaur : http://forum.xda-developers.com/showthread.php?t=914690&page=28
Click to expand...
Click to collapse
First tried to install final CM7.1.0 over nightly. Followed instructions here on Opening page Nook Color Android Development thread for this and then tried step-by-step Maurice Mongeon - Nook Color: updated Clockwork Recovery Bootable SD page. I left a similiar comment to this post at his page. Scroll up to see his instructions.
http://mrm3.net/nook-color-how-to-install-cyanogenmod-7-1/#comment-1069
From his site: Everything good from ROM Manager making sure latest CWR 3.2.0.1 until reboot into recovery. Get dark purple-black screen, have to power+n force it into internal CWR 3.2.0.1. Gets through Install from sdcard complete. Mounts and Storage > format /cache > Yes – Format gives me Error Formatting /cache!.
If I try format /system… it hangs. Reboot into CWR again it hangs again at Formatting /system… No way to format system, data, cache from Mounts and Storage to boot into clean new ROM!
I can use – wipe cache partition and – advanced > Wipe Dalvik Cache instead afted installing – update-cm-7.1.0-encore-signed.zip (correct checksum) from sd-card. Everything goes OK except it boots back into CyanogenMod-7-08192011-NIGHTLY-encore.
Restoring previous Nandroid from internal CWR or SD CWR also hangs at restoring /system. What should I do? Can not update or get it back to original 1.3 ROM either? Lockups and errors in Mounts and Storage formats stop me! Tried suggestions in this thread using the boot SD version of ClockworksMod Recovery, none of them seem to work. Anybody have any suggestions as to what to do next?

@ Izord and lschroeder.
If you guys absolutely cannot get it going with CM7, I then suggest trying to get back to the original, stock ROM.
If you had formatted /boot, then I cannot help since I never did mine so I don't know for sure but if not, you should be able to bring the NC back in the original stage.

votinh said:
@ Izord and lschroeder.
If you guys absolutely cannot get it going with CM7, I then suggest trying to get back to the original, stock ROM.
If you had formatted /boot, then I cannot help since I never did mine so I don't know for sure but if not, you should be able to bring the NC back in the original stage.
Click to expand...
Click to collapse
I can not get to stock ROM either, format/system... hangs and I have to hard reboot.
Question for anybody: Can I use ADB or adbWireless to help get around the format/system... error and install CM7.1.0 or Stock 1.3?

Sorry to resurrect an old thread but this is the only place I've found that describes my problem. I'm experiencing the exact same thing with my Nook Color and followed the exact same suggestions without success.
Was this ever resolved? What finally made it work?

This is exactly what is happening to me. I've already posted my problem to another thread but I thought I would comment here in case this thread finds a resolution.
BTW, my thread is http://forum.xda-developers.com/showthread.php?t=1578127

Stuck in the CW recovery screen, tried everything.

I searched everywhere, but can't find the same problem as mine. I am stuck in the CW recovery screen, after rebooting times after times.
I have been updating the CM9 nightly for a while, didn't have any problem. But when I tried to flash 02-17 nightly, I messed up and in the middle of the install (flash), I hold the power forcing to reboot. Now, it keeps going loop back to the CW recovery screen every time I tried to reboot.
--
I tried to reinstall the whole thing with the boot-able sdcard, but didn't work. please help! someone?
I tried to wipe, reformatted the system, data, cash, boot. Still stack at the cw recovery screen. Help...
I love my nook and have a road trip coming up. It will be nice to watch a kid movie to keep the kids entertained.

Had you flashed CmWR into eMMC?

Check the ROM information on /dev/block/mmcblk0p2.... this sounds a LOT like the problem 12paq had...
http://forum.xda-developers.com/showthread.php?t=1495913

@Dizzyden, thanks for the tip.
I did repartition to 1g/5g awhile back. I am not sure where to start. 12paq tried many things, which one was the solution? Your rombackup.zip?
Many thanks....

@votinh
what do you mean? I am not using the N&O apps or OS. Pure CM9, therefore I guess it is flashed in eMMC. If not, please advice.

DizzyDen said:
Check the ROM information on /dev/block/mmcblk0p2.... this sounds a LOT like the problem 12paq had...
http://forum.xda-developers.com/showthread.php?t=1495913
Click to expand...
Click to collapse
how can I check this"Check the ROM information on /dev/block/mmcblk0p2"?
please advice.
I tried to adb shell the nook, but not devices found? please help.
Finally, with the help from the good people of this forum, I was able to restore back to B&N, and reflash CM9 from there.
Thank to you all.

Yesterday my nook color was working great. Today I turned the screen on and it hung. Now I'm having the above problem with it hanging at clockwork recovery.
I've got CM7.1 stable on there running from emmc.

can't get adb to recognize the device since it is in cwr... how did you do it?

chilimac02 said:
can't get adb to recognize the device since it is in cwr... how did you do it?
Click to expand...
Click to collapse
Install the google drivers for adb... if you are in CWR adb is enabled... just have to get the drivers loaded on your computer.

try this:
http://forum.xda-developers.com/showthread.php?t=958748

dumper1234 said:
I searched everywhere, but can't find the same problem as mine. I am stuck in the CW recovery screen, after rebooting times after times.
I have been updating the CM9 nightly for a while, didn't have any problem. But when I tried to flash 02-17 nightly, I messed up and in the middle of the install (flash), I hold the power forcing to reboot. Now, it keeps going loop back to the CW recovery screen every time I tried to reboot.
--
I tried to reinstall the whole thing with the boot-able sdcard, but didn't work. please help! someone?
I tried to wipe, reformatted the system, data, cash, boot. Still stack at the cw recovery screen. Help...
I love my nook and have a road trip coming up. It will be nice to watch a kid movie to keep the kids entertained.
Click to expand...
Click to collapse
It may be that your "boot to recovery" flag is set, and if so, it will always boot to that until it is cleared. When the cyanogenmod logo comes up hold the n button until the boot menu comes up. Then choose boot to emmc. If it works, go to ROM Manager and flash a new CWM Recovery to emmc.

Welcome to the nightmare I lived last week. Don't worry I woke up, was able to fully recover and forget the dream ever occurred.
I to tried to reformat to 1gb/5gb and ended up in the same boot loop.. If you are in the same spot I was, your boot partition got wiped out. And you may notice EMMC is gone.
After much searching I came across a file... Looking....Looking...Looking...
..........................Ah yes here it is. Here is what worked for me.
1. Boot to recovery (Should be easy at this point)
2. Format System, Data, and Cache.
3. Install the attached Zip file. (RecoveryFix.zip), this should recreate the Boot partition and fix the EMMC.
4. Reboot to recovery
5. Install favorite Rom or restore from backup.
6. Reboot to test.
Again this is what finally worked for me, and I went through a lot of trial and error to get there. I am guessing at your situation being exactly the same as mine.
PS. Ignore my since of humor if you need to.

[Q] Cannot boot into anything, including CWR

Well, after a few weeks of reading posts, even opening up the hardware and taking the nook apart, here I am asking a question. I figure I would go to the source rather than those other place I was reading and tryign to get info from (mot os those places link here anyway). I know that everyone says that the nook is "unbrickable;" while I want to believe it, I may be in a place where it may be true.
I do want to add a thanks as well, since the NC "tablet" has been very handy, and my wife and I have really enjoyed it. Wouldn't have happened without you all. I wish I had more time to participate in developing, but working 80+ hours/week in a hospital limits my free time, as you can imagine.
I rooted the NC and installed Cyanogenmod 7 back in July 2011. It was a 1.1 model (if I recall correctly). I installed the mod to EMMC, along with CWM. Things ran fine for 6 months. Literally no issues. Then, one night the battery was dead, so I plugged it into the computer USB to charge while the machine was off. Didn't touch it at all. When I went to turn it on again, I was stuck in a bootloop. It would go to the cyanogenmod screen and say "Loading" then would start over again. So, I naturally made a bootable SD card, and tried going into CWR to fix things. However, the SD card had the bootloop as well. It would get to the two skulls and "Loading", flash blank, then start over again.
That went on for a while. I couldn't boot into anything, not into recovery, alternate images, literally nothing. So, I tried different images --- nothing. Finally, I did the power+n and got into the only screen that wouldn't keep resetting. It has blue text and says "Entering boot menu". The menu says "Encore U-boot Menu by j4mmr. 1.2 port+ extras by fattire." From this screen, I can navigate and change the boot options. However, once again, whatever I try does not actually boot, regardless of what I set it to. The only thing that I got from getting here was no more boot loops. After getting it to this point, I can try loading anything, and it will start, then the screen goes black/blank, and nothing happens. Left it on for hours to test.
Since that point, I have switched cards (SanDisk 2 GB class 4, Patriot 8 GB and a generic 8 GB microSD). I know that cards work correctly because I got a hold of a second nook, and they work fine on it. Below are a list of all the images I have tried to run off the SD. Again, nothing will boot, not even clockwork recovery/clockworkmod.
128 mb rootpack (IOMonster)
clockwork 3.0.2.8
clockwork 3.2.0.1 eyeballer
Nooter
Mirage_CM7_ICS_CM9_DualbootSD (this card works great on the working NC)
TWRP 2.0 RC0
Generic SD
Clockwork 0.7 -> starts boot loops again
I also tried ADB, connecting to the computer and using putty over SSH. Didn't work. 8 interrupted boots with 9th holding power+n. Nope. I even took the nook apart and disconnected the battery. Still no go.
If I recall, I think I had CWM 3.0.0.5 installed to the card and to the emmc.
If anyone has any other ideas, I could really use the help. I consider myself pretty computer literate (build my machines, coded in my spare time in the past, hacked a lot of my electronics). I have read many guides/sites and even tried the outdated stuff. Once again, I cannot get into clockwork recovery, so any guide that says to do that as the first step will not work. I also cannot boot off of the SD on cards that I know function.
Would using an older version of CWM (prior to 3.0.0.5) work? I think I remember reading a bunch of stuff about problems people were having with that version. The thing is, I wasn't installing or flashing anything new. I wish I was, because then I would know what was happening when everything got screwed up.
Thanks a bunch in advance for your guy's (gals?) time. This has been really painful.

Wow, that must be frustrating. First make sure you didn't change the boot settings to something other than the SD card when you were in the boot menu. As long as the Nook is powering on and doing something you can probably save it from being a brick.
I would start with a newer version of ClockWork Mod Recovery here: http://mrm3.net/blog/2011/03/11/nook-color-updated-clockwork-recovery-bootable-sd/
There is a contradiction in the file names but the actual version should be 3.2.0.8. If that doesn't work then you may want to go back to an older version. In that case I would still load a newer version's zip file onto that card, so that if you do get the older version to boot you can use it to flash the newer version.
Before going back to older CWM versions though give this a try if the new CWM above doesn't work http://forum.xda-developers.com/showthread.php?t=958748
JP

Yeah, it has been frustrating, especially not knowing what happened in the first place. I actually did try the version from that first link (where I put 3.0.2.8). Again, the big issue I am having is that I cannot even get into the CWM. If I could, I could fix it. I also saw and read through that xda thread you kinked to (open right now in my browser), but the problem remains that I cannot even get to the point where I can flash something.
Thanks at least for responding. I'll try a few more things and see if it works, but I am running out of ideas.

In theory creating a bootable CWM card will get you into recovery even though you can't access the Recovery on the internal. Once you reach Recovery from the SD card you can flash whatever you need. It is just a matter of making a bootable recovery card that boots far enough to get you there.

In theory, yes, but as I said in my first post, I tried all the bootable cards without any luck. When I try to set the SD card as primary boot from that one screen from fattire, it locks and never restarts.

J515OP said:
Wow, that must be frustrating. First make sure you didn't change the boot settings to something other than the SD card when you were in the boot menu. As long as the Nook is powering on and doing something you can probably save it from being a brick.
I would start with a newer version of ClockWork Mod Recovery here: http://mrm3.net/blog/2011/03/11/nook-color-updated-clockwork-recovery-bootable-sd/
There is a contradiction in the file names but the actual version should be 3.2.0.8. If that doesn't work then you may want to go back to an older version. In that case I would still load a newer version's zip file onto that card, so that if you do get the older version to boot you can use it to flash the newer version.
Before going back to older CWM versions though give this a try if the new CWM above doesn't work http://forum.xda-developers.com/showthread.php?t=958748
JP
Click to expand...
Click to collapse
This happened to me a couple of times on CM7. Don't know why, but I believe I used the last method listed to repair it. There was an older version of CWM that would cause this sometimes. When you get it going again, you must update CMW to the new one.

DigitalMD said:
This happened to me a couple of times on CM7. Don't know why, but I believe I used the last method listed to repair it. There was an older version of CWM that would cause this sometimes. When you get it going again, you must update CMW to the new one.
Click to expand...
Click to collapse
How did you get it to boot into CWM in the first place in order to flash? That is my current problem. Any method of fixing relies on the ability to boot into CWM from the SD card, which (for whatever reason) isn't working at the moment.
Well, tried to use the native Nook u-boot. Get the "Touch the Future of Reading" screen, then black, just like with any of the other cards. On the good nook, it boots into a linux file and runs the recovery script, so it is not the card reader or the SD card.

Well, still doesn't work. I guess I officially bricked it without even knowing what happened. Bummer.

czarofthefrozentundra said:
Well, still doesn't work. I guess I officially bricked it without even knowing what happened. Bummer.
Click to expand...
Click to collapse
You said you tried eyeballers 3.2.0.1 CWM. Did you mean the 1GB image file he posted on his thread? And how did you burn the image to the card? You should be using win32diskimager running in administrator mode on Windows. And it is best to use a cheap card reader rather than any card reader built into your PC. The nook can be really finicky about how the card is written.

leapinlar said:
You said you tried eyeballers 3.2.0.1 CWM. Did you mean the 1GB image file he posted on his thread? And how did you burn the image to the card? You should be using win32diskimager running in administrator mode on Windows. And it is best to use a cheap card reader rather than any card reader built into your PC. The nook can be really finicky about how the card is written.
Click to expand...
Click to collapse
Yes, I tried that image from his thread. I always use win32diskimager and use a card reader. I have working cards (I have a second NC that runs fine); there is just something wrong with the boot process, and I cannot get into CWR to fix it. It starts, but then never makes it in or reboots. Only time I can keep it from rebooting is by holding "n" and going into the boot option menu.

czarofthefrozentundra said:
Yes, I tried that image from his thread. I always use win32diskimager and use a card reader. I have working cards (I have a second NC that runs fine); there is just something wrong with the boot process, and I cannot get into CWR to fix it. It starts, but then never makes it in or reboots. Only time I can keep it from rebooting is by holding "n" and going into the boot option menu.
Click to expand...
Click to collapse
It goes to the boot menu when you hold n with eyeballers image burned to SD? What happens when you select SD and normal? Just a hang? With 'loading' showing?
Edit: I just thought of another reason that could be causing this. There is a flag set in /rom that tells the system to try to boot into recovery. It tries no matter what you tell it to do in the boot menu. ROM Manager uses that flag to boot to recovery when you tell it to. Then after you successfully get into recovery and exit it by telling CWM to reboot, CWM clears that flag. If your recovery is borked up, you never get that flag cleared and it's an endless loop.
There are two solutions I can think of. First, use racks dual boot SD that you already have and go into the boot menu with that. Tell it to go to SD and recovery. Hopefully his recovery will load. Then immediately exit by the menu. That should clear the flag. If that fixes it and it boots to CM7, go to ROM Manager and flash a new CWM to emmc.
If that does not fix it search xda for 'fix recovery'. There is a nook thread telling how to fix the recovery on emmc.
Edit2: I just thought of a third way to try to get it to boot. Take eyeballers 3.2.0.1 CWM SD and put it in your PC. There should be two files there named uImage and uRamdisk. Make a copy of them on the SD and rename the copies to uRecImg and uRecRam. Then put back in nook and reboot to see what you get.

Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.

czarofthefrozentundra said:
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
Click to expand...
Click to collapse
See my edit2 above for a third way to try to clear the flag.
Sent from my NookColor running ICS and Tapatalk

czarofthefrozentundra said:
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
Click to expand...
Click to collapse
Hello? Feedback?
Sent from my Nook Color running ICS and Tapatalk

Ha, I tried the quick reply function, and it didn't work. Here is what I wrote yesterday (verbatim, since I still had the window open):
"Well, so far no luck. Here is what I have tried, and the new information that I learned.
Used dual boot SD that I know works and booted into bootloader menu. Tried all different options on the SD card. What happens is that it thinks for a bit, then turns the screen black, but the boot screen never comes up (i.e. the Cyanogenmod logo that usually starts before things boot). So there must be some problem there.
If I hold down power, it will restart. Again, the screen turns black after the loading screen is on for a while (happens no matter which image I burned to the card).
I still need to try the other method (eyeballer one). I don't think the EMMC reset will work with my particular issue, as I had read that thread earlier."

czarofthefrozentundra said:
I still need to try the other method (eyeballer one).
Click to expand...
Click to collapse
If the problem is the recovery flag, the mods to the eyeballer CWM SD should work. If it does not work, it may be something else. If it does work you can flash a new CWM to emmc using another eyeballer zip. Get it here:
http://forum.xda-developers.com/showthread.php?p=21932561
You would want the first choice.
Sent from my Nook Color running ICS and Tapatalk

Cool. Will give it a try tonight and report back. Just have to find my spare SD card.

So, tried with the eyeballer, and I couldn't get it to work. One thing I did notice, though (actually by chance) is that even though the screen is black, the nook is on. I saw this because it all of the sudden started flashing the low battery screen and then turned off.
Anyhow, still looks like I am in the same position. The EMMC fix doesn't work for me because I cannot even boot of an SD card.
EDIT: Actually, I just reread your post. I didn't do it right. I am going to try again and report back.
EIDT 2: Nope, didn't work. Do I need to hold all the buttons down while booting or do something else special?

czarofthefrozentundra said:
So, tried with the eyeballer, and I couldn't get it to work. One thing I did notice, though (actually by chance) is that even though the screen is black, the nook is on. I saw this because it all of the sudden started flashing the low battery screen and then turned off.
Anyhow, still looks like I am in the same position. The EMMC fix doesn't work for me because I cannot even boot of an SD card.
EDIT: Actually, I just reread your post. I didn't do it right. I am going to try again and report back.
EIDT 2: Nope, didn't work. Do I need to hold all the buttons down while booting or do something else special?
Click to expand...
Click to collapse
I'm not sure what to tell you to do next. I guess I am going to send you to a post that tells pretty plainly how to do the 8 failed boots. I know you tried that, but timing is very critical with that procedure. Worth a try to me.
http://forum.xda-developers.com/showthread.php?p=25405429

How do you do the 8 failed boot deal with the cyanogenmod screen running. I am not sure about the timing of things. Also, which buttons? I have seen people do it with just the power button. Other places say with the power+n+vol up.

CM7 boot loop (racks triple boot)

Nook color running Racks triple boot via micro SD card. Micro SD card is a Sandisk 8GB class 4 card.
Was previously running fine for many months with the 2/2/12 roms. I would run CM7 99% of the time and I would get a random reboot here and there, but otherwise very stable.
A couple days ago, I had a random crash and tried to reboot CM7. I could get passed the boot loader screen, but then would have a continuous boot loop with the blue android symbol.
Thinking something was corrupted with the rom, I booted to recovery and tried flashed the rom along with gapps. Still boot looping.
I booted to CM9, and was able to run. So I downloaded the latest CM7 and CM9 roms for Racks triple boot. Flashed both along with the gapps and CM9 fix. Apparently I got lucky and was able to boot into CM7.... once. Thinking everything was OK, I went on with my life and ran the new CM7 happily.
Now, a few days later, I've tried to reboot and I'm back at the same boot loop with the arrow spiraling around the a blue skateboarding android. Note, in that short time that I was running the newest Racks triple boot CM7 rom, I did not run a backup, so, I'm basically out of luck with recovery via CWM.
I've flashed the 2/2/12 rom as well as the latest rom to see if either would work again. nothing... still boot looping... for hours now.
Any suggestions other than wiping the SD clean and starting with a fresh install?
Thanks all.
~mike

Bump...
Been a bit, no responses yet. Anyone have any ideas?
Thanks,
~mike

I think the fresh install will help since you already tried partial reinstalling the roms.
Produced by NookColor at ICS AOKP 4.0.4

Nook Color stuck in load screen
I have a nook with CM7 installed on it. was going return my nook to stock to give it to my little sister, but when i went to install the stock stuff back on it got stuck in a loop. It won't boot from an uSD card with clockwork on it and when I tried the 7 hard boot in a row trick, it didn't do anything. Did i really brick the thing? or can it be recovered?

doodlebug81 said:
I have a nook with CM7 installed on it. was going return my nook to stock to give it to my little sister, but when i went to install the stock stuff back on it got stuck in a loop. It won't boot from an uSD card with clockwork on it and when I tried the 7 hard boot in a row trick, it didn't do anything. Did i really brick the thing? or can it be recovered?
Click to expand...
Click to collapse
You are in a recovery bootloop with no recovery installed. Go to my tips thread linked in my signature. Read item A8. You need to make and use my special bootable CWM SD (select the 'larger' image). Then if you want to return to stock, read item A15.

[Q] Stuck on Cyanoboot loading screen..

I have a Nook Color that I've used for some time with CyanogenMod 10.2 with no problems. Last night I was looking at the fixes for Netflix since CM currently has a problem with it, and followed the instructions on XDS for the xposed installer (loading Liquid64's NetflixHackPersist.zip). Things appeared to go fine, and it booted into CM again and I ran the app as instructed. Everything seemed fine up to that point.
But on rebooting, the Nook will not go past the Cyanboot screen. Whether I let it boot by itself, or go to the boot menu and select any of the emmc or SD card options, it just sits there saying it's 'loading xxx' whatever option I've selected and never gets past it. I cannot find a way to force it to boot to the SD card to try anything that way.
I've tried 2 SD cards, reformatted and reburned an 8gb clockwork 3.0.2.8 image to make them bootable...so I don't think it's a card problem.
I'd appreciate some help if anyone knows a way around this. I've had experience with rooting and loading from the SD card, but if it always gets to Cyanoboot and I can't get it to even boot the SD card, I'm stuck. (The 8-reboots trick doesn't seem to work..I've likely reworked too much to still do that.)
Thanks,
JT

jttraverse said:
I have a Nook Color that I've used for some time with CyanogenMod 10.2 with no problems. Last night I was looking at the fixes for Netflix since CM currently has a problem with it, and followed the instructions on XDS for the xposed installer (loading Liquid64's NetflixHackPersist.zip). Things appeared to go fine, and it booted into CM again and I ran the app as instructed. Everything seemed fine up to that point.
But on rebooting, the Nook will not go past the Cyanboot screen. Whether I let it boot by itself, or go to the boot menu and select any of the emmc or SD card options, it just sits there saying it's 'loading xxx' whatever option I've selected and never gets past it. I cannot find a way to force it to boot to the SD card to try anything that way.
I've tried 2 SD cards, reformatted and reburned an 8gb clockwork 3.0.2.8 image to make them bootable...so I don't think it's a card problem.
I'd appreciate some help if anyone knows a way around this. I've had experience with rooting and loading from the SD card, but if it always gets to Cyanoboot and I can't get it to even boot the SD card, I'm stuck. (The 8-reboots trick doesn't seem to work..I've likely reworked too much to still do that.)
Thanks,
JT
Click to expand...
Click to collapse
Try using CWM 6.0.4.7.

hwong96 said:
Try using CWM 6.0.4.7.
Click to expand...
Click to collapse
Hallelujah! I followed your link and (though what I saw suggested trying CWM 5.5.04 for CM 10.2) it WORKED!! It booted to the SD card from Cyanboot, and I had a CM 10.2.1 zip that I was able to install and I'm back in business.
Out of curiosity, is Cyanoboot something unremovable, meaning I can never simply boot straight to an SD card as in the past? It did let me get to the recovery on this SD card, so I guess Cyanoboot was actually working and my problem was something else...but if I simply did a factory reset and wiped everything, would that have removed Cyanoboot as well?
If anyone has suggestions, I'm trying to decide if I'll keep this thing or sell it, so I'm curious what the most fully functional ROM (CM or ?) is considered to be these days, if I didn't put it back to stock?
I've loved this Nook, and only got into the earlier predicament because I thought, if I sold it, a buyer might want to use Netflix...so I was hoping to have it working with a ROM that would please the average Joe user who might hit up Youtube, Netflix, etc.
Thanks for the help!
JT

jttraverse said:
Hallelujah! I followed your link and (though what I saw suggested trying CWM 5.5.04 for CM 10.2) it WORKED!! It booted to the SD card from Cyanboot, and I had a CM 10.2.1 zip that I was able to install and I'm back in business.
Out of curiosity, is Cyanoboot something unremovable, meaning I can never simply boot straight to an SD card as in the past? It did let me get to the recovery on this SD card, so I guess Cyanoboot was actually working and my problem was something else...but if I simply did a factory reset and wiped everything, would that have removed Cyanoboot as well?
If anyone has suggestions, I'm trying to decide if I'll keep this thing or sell it, so I'm curious what the most fully functional ROM (CM or ?) is considered to be these days, if I didn't put it back to stock?
I've loved this Nook, and only got into the earlier predicament because I thought, if I sold it, a buyer might want to use Netflix...so I was hoping to have it working with a ROM that would please the average Joe user who might hit up Youtube, Netflix, etc.
Thanks for the help!
JT
Click to expand...
Click to collapse
If you installed CWM 6.0.4.7 to emmc and want to return to stock go to Leapinlar's tips item A12 on how to return to stock recovery. Or item A15 to flash BN stock recovery using CWM.
http://forum.xda-developers.com/showthread.php?p=25354258#post25354258