Well, after a few weeks of reading posts, even opening up the hardware and taking the nook apart, here I am asking a question. I figure I would go to the source rather than those other place I was reading and tryign to get info from (mot os those places link here anyway). I know that everyone says that the nook is "unbrickable;" while I want to believe it, I may be in a place where it may be true.
I do want to add a thanks as well, since the NC "tablet" has been very handy, and my wife and I have really enjoyed it. Wouldn't have happened without you all. I wish I had more time to participate in developing, but working 80+ hours/week in a hospital limits my free time, as you can imagine.
I rooted the NC and installed Cyanogenmod 7 back in July 2011. It was a 1.1 model (if I recall correctly). I installed the mod to EMMC, along with CWM. Things ran fine for 6 months. Literally no issues. Then, one night the battery was dead, so I plugged it into the computer USB to charge while the machine was off. Didn't touch it at all. When I went to turn it on again, I was stuck in a bootloop. It would go to the cyanogenmod screen and say "Loading" then would start over again. So, I naturally made a bootable SD card, and tried going into CWR to fix things. However, the SD card had the bootloop as well. It would get to the two skulls and "Loading", flash blank, then start over again.
That went on for a while. I couldn't boot into anything, not into recovery, alternate images, literally nothing. So, I tried different images --- nothing. Finally, I did the power+n and got into the only screen that wouldn't keep resetting. It has blue text and says "Entering boot menu". The menu says "Encore U-boot Menu by j4mmr. 1.2 port+ extras by fattire." From this screen, I can navigate and change the boot options. However, once again, whatever I try does not actually boot, regardless of what I set it to. The only thing that I got from getting here was no more boot loops. After getting it to this point, I can try loading anything, and it will start, then the screen goes black/blank, and nothing happens. Left it on for hours to test.
Since that point, I have switched cards (SanDisk 2 GB class 4, Patriot 8 GB and a generic 8 GB microSD). I know that cards work correctly because I got a hold of a second nook, and they work fine on it. Below are a list of all the images I have tried to run off the SD. Again, nothing will boot, not even clockwork recovery/clockworkmod.
128 mb rootpack (IOMonster)
clockwork 3.0.2.8
clockwork 3.2.0.1 eyeballer
Nooter
Mirage_CM7_ICS_CM9_DualbootSD (this card works great on the working NC)
TWRP 2.0 RC0
Generic SD
Clockwork 0.7 -> starts boot loops again
I also tried ADB, connecting to the computer and using putty over SSH. Didn't work. 8 interrupted boots with 9th holding power+n. Nope. I even took the nook apart and disconnected the battery. Still no go.
If I recall, I think I had CWM 3.0.0.5 installed to the card and to the emmc.
If anyone has any other ideas, I could really use the help. I consider myself pretty computer literate (build my machines, coded in my spare time in the past, hacked a lot of my electronics). I have read many guides/sites and even tried the outdated stuff. Once again, I cannot get into clockwork recovery, so any guide that says to do that as the first step will not work. I also cannot boot off of the SD on cards that I know function.
Would using an older version of CWM (prior to 3.0.0.5) work? I think I remember reading a bunch of stuff about problems people were having with that version. The thing is, I wasn't installing or flashing anything new. I wish I was, because then I would know what was happening when everything got screwed up.
Thanks a bunch in advance for your guy's (gals?) time. This has been really painful.
Wow, that must be frustrating. First make sure you didn't change the boot settings to something other than the SD card when you were in the boot menu. As long as the Nook is powering on and doing something you can probably save it from being a brick.
I would start with a newer version of ClockWork Mod Recovery here: http://mrm3.net/blog/2011/03/11/nook-color-updated-clockwork-recovery-bootable-sd/
There is a contradiction in the file names but the actual version should be 3.2.0.8. If that doesn't work then you may want to go back to an older version. In that case I would still load a newer version's zip file onto that card, so that if you do get the older version to boot you can use it to flash the newer version.
Before going back to older CWM versions though give this a try if the new CWM above doesn't work http://forum.xda-developers.com/showthread.php?t=958748
JP
Yeah, it has been frustrating, especially not knowing what happened in the first place. I actually did try the version from that first link (where I put 3.0.2.8). Again, the big issue I am having is that I cannot even get into the CWM. If I could, I could fix it. I also saw and read through that xda thread you kinked to (open right now in my browser), but the problem remains that I cannot even get to the point where I can flash something.
Thanks at least for responding. I'll try a few more things and see if it works, but I am running out of ideas.
In theory creating a bootable CWM card will get you into recovery even though you can't access the Recovery on the internal. Once you reach Recovery from the SD card you can flash whatever you need. It is just a matter of making a bootable recovery card that boots far enough to get you there.
In theory, yes, but as I said in my first post, I tried all the bootable cards without any luck. When I try to set the SD card as primary boot from that one screen from fattire, it locks and never restarts.
J515OP said:
Wow, that must be frustrating. First make sure you didn't change the boot settings to something other than the SD card when you were in the boot menu. As long as the Nook is powering on and doing something you can probably save it from being a brick.
I would start with a newer version of ClockWork Mod Recovery here: http://mrm3.net/blog/2011/03/11/nook-color-updated-clockwork-recovery-bootable-sd/
There is a contradiction in the file names but the actual version should be 3.2.0.8. If that doesn't work then you may want to go back to an older version. In that case I would still load a newer version's zip file onto that card, so that if you do get the older version to boot you can use it to flash the newer version.
Before going back to older CWM versions though give this a try if the new CWM above doesn't work http://forum.xda-developers.com/showthread.php?t=958748
JP
Click to expand...
Click to collapse
This happened to me a couple of times on CM7. Don't know why, but I believe I used the last method listed to repair it. There was an older version of CWM that would cause this sometimes. When you get it going again, you must update CMW to the new one.
DigitalMD said:
This happened to me a couple of times on CM7. Don't know why, but I believe I used the last method listed to repair it. There was an older version of CWM that would cause this sometimes. When you get it going again, you must update CMW to the new one.
Click to expand...
Click to collapse
How did you get it to boot into CWM in the first place in order to flash? That is my current problem. Any method of fixing relies on the ability to boot into CWM from the SD card, which (for whatever reason) isn't working at the moment.
Well, tried to use the native Nook u-boot. Get the "Touch the Future of Reading" screen, then black, just like with any of the other cards. On the good nook, it boots into a linux file and runs the recovery script, so it is not the card reader or the SD card.
Well, still doesn't work. I guess I officially bricked it without even knowing what happened. Bummer.
czarofthefrozentundra said:
Well, still doesn't work. I guess I officially bricked it without even knowing what happened. Bummer.
Click to expand...
Click to collapse
You said you tried eyeballers 3.2.0.1 CWM. Did you mean the 1GB image file he posted on his thread? And how did you burn the image to the card? You should be using win32diskimager running in administrator mode on Windows. And it is best to use a cheap card reader rather than any card reader built into your PC. The nook can be really finicky about how the card is written.
leapinlar said:
You said you tried eyeballers 3.2.0.1 CWM. Did you mean the 1GB image file he posted on his thread? And how did you burn the image to the card? You should be using win32diskimager running in administrator mode on Windows. And it is best to use a cheap card reader rather than any card reader built into your PC. The nook can be really finicky about how the card is written.
Click to expand...
Click to collapse
Yes, I tried that image from his thread. I always use win32diskimager and use a card reader. I have working cards (I have a second NC that runs fine); there is just something wrong with the boot process, and I cannot get into CWR to fix it. It starts, but then never makes it in or reboots. Only time I can keep it from rebooting is by holding "n" and going into the boot option menu.
czarofthefrozentundra said:
Yes, I tried that image from his thread. I always use win32diskimager and use a card reader. I have working cards (I have a second NC that runs fine); there is just something wrong with the boot process, and I cannot get into CWR to fix it. It starts, but then never makes it in or reboots. Only time I can keep it from rebooting is by holding "n" and going into the boot option menu.
Click to expand...
Click to collapse
It goes to the boot menu when you hold n with eyeballers image burned to SD? What happens when you select SD and normal? Just a hang? With 'loading' showing?
Edit: I just thought of another reason that could be causing this. There is a flag set in /rom that tells the system to try to boot into recovery. It tries no matter what you tell it to do in the boot menu. ROM Manager uses that flag to boot to recovery when you tell it to. Then after you successfully get into recovery and exit it by telling CWM to reboot, CWM clears that flag. If your recovery is borked up, you never get that flag cleared and it's an endless loop.
There are two solutions I can think of. First, use racks dual boot SD that you already have and go into the boot menu with that. Tell it to go to SD and recovery. Hopefully his recovery will load. Then immediately exit by the menu. That should clear the flag. If that fixes it and it boots to CM7, go to ROM Manager and flash a new CWM to emmc.
If that does not fix it search xda for 'fix recovery'. There is a nook thread telling how to fix the recovery on emmc.
Edit2: I just thought of a third way to try to get it to boot. Take eyeballers 3.2.0.1 CWM SD and put it in your PC. There should be two files there named uImage and uRamdisk. Make a copy of them on the SD and rename the copies to uRecImg and uRecRam. Then put back in nook and reboot to see what you get.
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
czarofthefrozentundra said:
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
Click to expand...
Click to collapse
See my edit2 above for a third way to try to clear the flag.
Sent from my NookColor running ICS and Tapatalk
czarofthefrozentundra said:
Hmm. Thanks. I'll definitely give it a shot (got nothing to lose at this point). I'll get back and let you know if it worked or not.
Click to expand...
Click to collapse
Hello? Feedback?
Sent from my Nook Color running ICS and Tapatalk
Ha, I tried the quick reply function, and it didn't work. Here is what I wrote yesterday (verbatim, since I still had the window open):
"Well, so far no luck. Here is what I have tried, and the new information that I learned.
Used dual boot SD that I know works and booted into bootloader menu. Tried all different options on the SD card. What happens is that it thinks for a bit, then turns the screen black, but the boot screen never comes up (i.e. the Cyanogenmod logo that usually starts before things boot). So there must be some problem there.
If I hold down power, it will restart. Again, the screen turns black after the loading screen is on for a while (happens no matter which image I burned to the card).
I still need to try the other method (eyeballer one). I don't think the EMMC reset will work with my particular issue, as I had read that thread earlier."
czarofthefrozentundra said:
I still need to try the other method (eyeballer one).
Click to expand...
Click to collapse
If the problem is the recovery flag, the mods to the eyeballer CWM SD should work. If it does not work, it may be something else. If it does work you can flash a new CWM to emmc using another eyeballer zip. Get it here:
http://forum.xda-developers.com/showthread.php?p=21932561
You would want the first choice.
Sent from my Nook Color running ICS and Tapatalk
Cool. Will give it a try tonight and report back. Just have to find my spare SD card.
So, tried with the eyeballer, and I couldn't get it to work. One thing I did notice, though (actually by chance) is that even though the screen is black, the nook is on. I saw this because it all of the sudden started flashing the low battery screen and then turned off.
Anyhow, still looks like I am in the same position. The EMMC fix doesn't work for me because I cannot even boot of an SD card.
EDIT: Actually, I just reread your post. I didn't do it right. I am going to try again and report back.
EIDT 2: Nope, didn't work. Do I need to hold all the buttons down while booting or do something else special?
czarofthefrozentundra said:
So, tried with the eyeballer, and I couldn't get it to work. One thing I did notice, though (actually by chance) is that even though the screen is black, the nook is on. I saw this because it all of the sudden started flashing the low battery screen and then turned off.
Anyhow, still looks like I am in the same position. The EMMC fix doesn't work for me because I cannot even boot of an SD card.
EDIT: Actually, I just reread your post. I didn't do it right. I am going to try again and report back.
EIDT 2: Nope, didn't work. Do I need to hold all the buttons down while booting or do something else special?
Click to expand...
Click to collapse
I'm not sure what to tell you to do next. I guess I am going to send you to a post that tells pretty plainly how to do the 8 failed boots. I know you tried that, but timing is very critical with that procedure. Worth a try to me.
http://forum.xda-developers.com/showthread.php?p=25405429
How do you do the 8 failed boot deal with the cyanogenmod screen running. I am not sure about the timing of things. Also, which buttons? I have seen people do it with just the power button. Other places say with the power+n+vol up.
Related
Hi,
I've searched the forums but haven't found a solution to my problem. I rooted my Nook Color (1.1.0) using auto-nooter 3.0. Everything worked fine, then I tried to flash to CM7 using CWM. When I subsequently rebooted, the Nook goes into a boot loop where it never gets past the "Touch the Future of...." display before it reboots.
I've can't get into ADB because the unit reboots before I can get access. Also tried booting into CWM (3.0.0.5 and 3.0.1) on an SD Card. When I do this, it shows the "loading..." display for a few seconds then reverts to the boot cycle. Also tried nooter 0.2 but same result.
Tried doing 8 successive boot cycles by trying to turn it off before it reboots, but no luck.
I've noticed that others have had boot issues also, but it seems that everyone else has been able to eventually boot back into CWM via SD card.
If anyone has any suggestions, I would definitely appreciate the help.
Thanks.
I experienced this exact problem and never did get it working. I was running Nookie Froyo on SD with overclock when it suddenly started rebooting. Doesn't matter if the card is in or out, it gets to the point you describe and reboots. All of the "restore to stock' tricks failed because it keeps rebooting, even when booting into CWM from SD. I ended up replacing it with another new NC and put the the first one in storage hoping I someday figure out the problem. I've never found anyone else with quite this problem. I'll be anxiously watching this thread!
Not sure whether I should start to panic because you never got it working, or feel relieved because I am not the only one to experience this issue
You can add another person who is having this problem.
Yesterday I asked Rom manager to boot into recovery and that was all she wrote.
The nook gets through "Touch the future of reading," then the screen flashes for a fraction of a second before repeating the process again.
Holding 'n' and power while booting also has no affect; and it seems to ignore whatever is in the SD card slot.
Got it working!
Not exactly how this worked but here is what I did.
First off I used another SD Card Reader Although the idea of using another card reader doesn't seem to make sense; I had seen it on another forum.
I also Used a new uSD card
Used Win32DiskImage to burn the image to the uSD card (had been using DD on a linux box)
The images used was the Clockwork Recovery image (2GB,) look around and you should be able to find it.
I also copied the removeclockwork.zip
This should be available with a google search as well
From there it just worked like it was supposed to. The nook booted off the micro SD card and I used the removecwr.zip
Hope this helps
I will post the long version here, mainly because I have nothing better to do.
Here is the situation. I bought a NC about 6 months ago. I rooted it using Auto Nooter. I have no idea what ROM I installed to be honest. I'm very much a novice at this. And I'm quite stupid to boot, I might add. It has worked relatively ok since then. The ROM seemed a bit buggy and I had some initial troubles with constant reboots, in addition to some basic things not working and way bogging the thing down, but in general it was ok. I haven't used it much since unless I was traveling.
Today....I was traveling. Traveling to BFE. As such, I decided to bust out my trusty NC and download a new book while I was waiting for my flight. I did so, and something went a bit haywire. It seems that somehow, without prompting, the device has restored itself to the stock B&N ROM (1.1 maybe?). Yet - the Android OS is still there. For example I can click on my task manager app in the lower left corner of the homescreen and it shows that all of my apps are running and I can even switch to them. But my homescreen is defaulted to the B&N one showing my eBooks and I can't figure out how to get my Android launcher back. I have tried to reboot and it does the Droid boot up but reverts to the same B&N home screen.
I was thinking about trying to update to a new ROM since it had been awhile and I figured there must be something better/more stable out there now - Honeycomb or whatever. I guess this is the kick in the ass that I needed.
So now here I sit in a hotel room in BFE. There are no restaurants open past 9. There are no bars. There IS a Super Wal Mart but I think I'm gonna pass on that.
I figured I would look into this. Where to start? Should I re-set this thing to stock and then just pick a new ROM and re-root? Can I do any of this without having a SD card slot in my laptop - just using a USB cable? Will I lose any eBooks that I downloaded?
I await your sage advice.
rooting actually means gaining super user access to the current android rom. B&N, i believe is Froyo, so you did not install any rom so to speak. you were probably just rooted.
I think the issue is with the launcher and not that it is back to stock. What happens when you long press on the home screen?
If you plan to do anything, you will definitely need an sd card reader.
If you autonootered, then you were running stock, but rooted. With a custom launcher replacing the stock launcher, it sounds like.
At any rate, you were probably hit with the automatic update to B&N 1.2 (which is Android 2.2, iirc.) You almost certainly aren't rooted anymore, but it may allow you to run any apps that you already had downloaded, just from the stock app launcher.
When you get an SD card reader, you can check out Manual Nootering. It's basically the same as the old Auto Nooter, but for B&N 1.2. If you change the rom entirely (install CM7) or just run a different rom from an SD card, you'll avoid having B&N overwrite your root access in the future.
Thanks for the responses. I believe that you are correct. I actually was running 1.0.0. I used auto-nooter to root the thing and had it working with a custom launcher. I don't think it updated to 1.2. In fact I know that it didn't update to 1.2. I am trying to get it to do that right now.
I would like to install a new ROM or root or do something after it updates to 1.2 so that I have access to the Android market. What is my best way to do this? Should I just root again from 1.2? Should I install this CM7?
Can you help me understand the differences? Thanks again.
I could Super Wal Mart tonight for a SD card reader if I'm feeling frisky.
I've got all kinds of problems.
I went to update to 1.2 from 1.0. I removed my SD card and erased and deregistered device. I booted it back up and it thinks it's a phone. I put the 1.2 file in the root drive via USB, as I have read over and over that the thing should recognize the 1.2 file and reboot itself. It's not working. I erased and deregistered again. same deal.
Any advice?
I'd do a full factory reset, then try the update to 1.2 again.
A couple of things about the 1.2 update -- do not unzip the update file or rename it. Just drop it as-is into the nook. And make sure to eject the nook from your computer and unplug it.
Thank you aka. I got it to take. I am now at 1.2. Now back to square 1(.2). Any help on this?
Baboontyme said:
I would like to install a new ROM or root or do something after it updates to 1.2 so that I have access to the Android market. What is my best way to do this? Should I just root again from 1.2? Should I install this CM7?
Can you help me understand the differences? Thanks again.
Click to expand...
Click to collapse
Baboontyme said:
I booted it back up and it thinks it's a phone. I put the 1.2 file in the root drive via USB, as I have read over and over that the thing should recognize the 1.2 file and reboot itself. It's not working. I erased and deregistered again. same deal.
Click to expand...
Click to collapse
ETA: lol, congratulations! I guess just skip to that link at the end.
I'd agree with akaCat that you should do a factory reset, BUT you can only do that if you still have the stock recovery utility, and it seems possible that you do not. Try to get the NC to reset by interrupting the boot 8 times. If it doesn't work, you may have installed ClockworkMod Recovery on your Nook Color in place of the stock recovery utility. You may have done so while rooting, or later from the ROM Manager app, perhaps even by accident.
Have you attempted to boot to recovery by holding down "n" while you power on the device, and continuing to hold power + n for about six seconds (1-one-thousand, 2-one-thousand, etc), then releasing both? If so, do you get a factory reset dialog (series of yes/no options) or a longer menu including items like "mounting and storage" and "flash zip from sd card?" If you get the longer menu, then that's ClockworkMod Recovery, and neither the 8-failed-boots-reset nor the automatic update are going to work.
If you do have ClockworkMod Recovery, don't do anything yet. Hopefully somewhere on the screen it tells you the version number, in the format 3.0.x.x. Just let us know that version number and power off the NC.
If you still have the stock recovery utility, then do the factory reset, boot into the stock OS, connect USB, drop the update file straight on the Nook (not in any folders), safely remove the NC from your PC, and let it sit. Hopefully it will reboot itself.
If not, the next step is probably going to involve preparing a bootable ClockworkMod SD and manually installing a CWM-compatible version of the update, or of a different ROM. This article may help you wrap your head around the different options: http://quinxy.com/guides/how-to-pick-your-nook-color-operating-system-and-install-options/
ETA: lol, congratulations! I guess just skip to that link at the end.
Thank you, Tao. I seem to be a bit stuck, though.
I'm at 1.2 stock. I was able to reformat and erase my sd card. I went to load the .gz image onto the card (for CM7, per instructions here http://forum.xda-developers.com/showthread.php?t=1000957) and I also loaded the nightly build. Then inserted card into NC and booted. Nothing.
Any idea what I'm doing wrong? Should I unzip either file?
One thing that might/might not matter....when I went to eject the SD card from my PC, I wasn't given that option so I just pulled it.
One more thing.....the instructions at the link above instruct you to "write the image to your SD card" but then go on to say "eject the SD card" and then further "insert the uSD card into your computer"
Huh?? Isn't it all on the same card? Why do I need two different cards? What am I missing?
This blog breaks down the same process a little more step-by-step, with videos: http://www.anamardoll.com/2011/04/ereader-running-cm7-firmware-on-nook.html
You can skip the long preamble down to "Ready? Let's get started."
You do need to unzip the disk image, and write it to the SD using a program like Win32DiskImager or WinImage. It's also definitely a good idea to safely eject the SD card from your PC.
Hi Tao and others. Thanks again for all of your help. I'm almost there!
I followed this Ana chick's directions and I have CM7 booting up. I am now at the stage where I am trying to boot up in recovery mode so I can get the google apps and wifi thing going. I can't get it to work! I am holding down the "n"/home button and then the power button and it keeps booting up with CM7. I've tried it probably 20 times. Any help? Thanks!
Can someone also tell me how to access the book I just purchased and was in the middle of reading? Do I have to go somewhere and re-download?
Baboontyme said:
Hi Tao and others. Thanks again for all of your help. I'm almost there!
I followed this Ana chick's directions and I have CM7 booting up. I am now at the stage where I am trying to boot up in recovery mode so I can get the google apps and wifi thing going. I can't get it to work! I am holding down the "n"/home button and then the power button and it keeps booting up with CM7. I've tried it probably 20 times. Any help? Thanks!
Click to expand...
Click to collapse
I should add that though I can get CM7 to boot, I never get "The Power of Reading". It's just kind of a flash.
That's all normal--verygreen had to make a new uboot, which no longer shows "The Power of Reading" and also flies through a recovery boot so fast you could miss it. If gapps didn't install, just make sure the .zip is still in the boot partition and keep trying. I'm pretty sure holding power > reboot > recovery boot works now from within CM7, but I would go into Settings>Accounts and try to sign in to Google before assuming it didn't install.
If the book was a B&N purchase, once you have the market working, just install the Nook app and sign into your account, and you should be able to re-d/l the book, possibly even still synced to where you left off.
Thank you so much Tao and others. Up and running with CM7. Any additional mods I should be messing with?
btw, you can also boot into recovery through rom manager, its easier.
Baboontyme said:
Thank you so much Tao and others. Up and running with CM7. Any additional mods I should be messing with?
Click to expand...
Click to collapse
You can overclock: http://forum.xda-developers.com/showthread.php?t=925451
Just make sure you grab the version for SD, and install it just like gapps, then set clock speed via CyanogenMod Settings>Performance>CPU
boxcar8028 said:
btw, you can also boot into recovery through rom manager, its easier.
Click to expand...
Click to collapse
Easier than holding power a sec, poking "Reboot," then "Reboot to Recovery?"
Really, it's about the same either way, depending how handy ROM manager is on your system.
Ok. Let me start by saying, I'm obviously not an expert on hacking/developing and stuff like that. I just love to tinker stuff so I learn in the process. So definitely not an expert. Just posted this thread hoping that someone whose possibly a lot more knowledgeable than I am would notice it and hopefully shed a light on this question.
Is TWRP 2.0 which can be seen here, working/compatible/available/will be available on our beloved NookColor?
All we are using right now is the ClockWorkMod Recoveries, right? Which I believe the latest is 3.2.0.1. I'm not saying at all that CWM is not sufficient enough to do whatever it needs to do, I just thought it would be awesome to be able to get your recovery things done THAT MUCH COOLER, navigating the device via the touchscreen rather than hardware buttons.
Hope this sparks more awareness!
+1 - I would like to see TWRP on our devices as well, BUT ... I would definitely miss the convenience of being able to install the nightlies directly from ROM manager.
OK, saying that, I also just had a perma-brick on my Nook and am getting a replacement due to an issue that occurred in recovery. I was stuck in the infamous CWR boot-loop, so did a restore, when I went to reboot, screen itself would never come on again - not after charge, not after holding buttons, nothing.
Is it related, I don't know, maybe not, but makes you think.
majorpay said:
+1 - I would like to see TWRP on our devices as well, BUT ... I would definitely miss the convenience of being able to install the nightlies directly from ROM manager.
OK, saying that, I also just had a perma-brick on my Nook and am getting a replacement due to an issue that occurred in recovery. I was stuck in the infamous CWR boot-loop, so did a restore, when I went to reboot, screen itself would never come on again - not after charge, not after holding buttons, nothing.
Is it related, I don't know, maybe not, but makes you think.
Click to expand...
Click to collapse
Oooh, that's too bad. And scary. Makes you worry about doing something that's not tried on the NookColor before. I wont dive in unless the devs really says that it's safe.
Hey, about your NC being bricked. I had something pretty similar happened to my NookColor before. Got stuck into a boot loop. Now before, I had my TitaniumBackup folder stored in the eMMC and I didn't want to do anything that would delete it. What I did is, I had another microSD card and created a bootable CWM. I installed a CM7 nightly on the microSD. Upon booting to the microSD build, I went and have adb wireless transfer my eMMC files to my PC. Now that I've recovered my TitaniumBackup folder, I formatted everything on my NC using the bootable CWM. Then what I did is I flashed the stock NC Rom which was 1.2 version. I did a factory reset. After that I had everything back to normal again. I flashed the nightly build on the eMMC again and from then on, had my TitaniumBackup folder on the microSD. Have you tried creating a bootable microSD?
A little late...
Did you try a formatted bootable sdcard? The nook is near indestructible. I had the same issue and recovered.
fr4nk1yn said:
Did you try a formatted bootable sdcard? The nook is near indestructible. I had the same issue and recovered.
Click to expand...
Click to collapse
Same here, I put together a nookie froyo card, and got bootloops.I took the memcard out and still got bootloops. I put a cwm card in, and STILL got bootloops. Then I made a new cwm card, and it booted just fine.
I see that there are other posts on this same subject and I have looked through them to try and fix my problem but I haven't found a proper solution yet. I rooted my NC (1.4.3) cm7 and it worked alright after that but apps weren't available for the version so I attempted an update then reboot. I powered down and pulled the micro sd then powered up and it gets to "Read Forever" then goes black. I have tried cm10 with manual nooter in order to try and re-do the partition on the device but it won't do anything once I put the card in and try to boot. I have had to dis-assemble it so that I can pull the battery and get it to power down completely. I have tried a factory reset boot, sd card boot with auto nooter, manual nooter, cm7, cm10, and other options on the sd card, I have also tried to boot directly from internal memory. I have tried the process of plugging it into the computer through the usb cable. I have charged the battery completely so that isn't a problem.
I have read that it is virtually impossible to brick this thing but I think I might have succeeded....any input on what I can try next would be helpful...
Fatguy86 said:
I see that there are other posts on this same subject and I have looked through them to try and fix my problem but I haven't found a proper solution yet. I rooted my NC (1.4.3) cm7 and it worked alright after that but apps weren't available for the version so I attempted an update then reboot. I powered down and pulled the micro sd then powered up and it gets to "Read Forever" then goes black. I have tried cm10 with manual nooter in order to try and re-do the partition on the device but it won't do anything once I put the card in and try to boot. I have had to dis-assemble it so that I can pull the battery and get it to power down completely. I have tried a factory reset boot, sd card boot with auto nooter, manual nooter, cm7, cm10, and other options on the sd card, I have also tried to boot directly from internal memory. I have tried the process of plugging it into the computer through the usb cable. I have charged the battery completely so that isn't a problem.
I have read that it is virtually impossible to brick this thing but I think I might have succeeded....any input on what I can try next would be helpful...
Click to expand...
Click to collapse
A good place to start with boot problems is here http://forum.xda-developers.com/showthread.php?t=949699
You should also probably read at least the first two post in this thread http://forum.xda-developers.com/showthread.php?t=1621301
You need to do a better job of describing your situation if you want help: how your NC was set up; exactly what you did that created the problem; what you want to end up with. At a guess, I will assume the you were running rooted stock on EMMC and CM7 on SD, decided to update CM7 to CM10, but used directions for updating CM that was installed to EMMC. I am not an expert on this, but sort of remember Leapinlar posting advice for someone (or maybe a few (?dozen?) someones) with this problem, you might want to search for those threads. If not, you have probably corrupted your boot records, recovery and/or possibly some partitions. Check out this thread by Leapinlar for help http://forum.xda-developers.com/showthread.php?t=1759558
If you decide to install CM on EMMC, see this thread http://forum.xda-developers.com/showthread.php?t=1030227
To install stock BN firmware to EMMC, see this thread http://forum.xda-developers.com/showthread.php?t=931720
To install CM on SD, see this http://forum.xda-developers.com/showthread.php?t=1941858
Good luck and don't forget to hit the thanks button in the posts you use
webyrd said:
A good place to start with boot problems is here http://forum.xda-developers.com/showthread.php?t=949699
You should also probably read at least the first two post in this thread http://forum.xda-developers.com/showthread.php?t=1621301
You need to do a better job of describing your situation if you want help: how your NC was set up; exactly what you did that created the problem; what you want to end up with
Good luck and don't forget to hit the thanks button in the posts you use
Click to expand...
Click to collapse
Here are the exact steps that I took to get to where I am:
I rooted the stock EMMC with the manual nooter to be able to get the Google Play Market, that worked well and I had access but the Android version was so old that I couldn't install the apps that I was after.
I then attempted to flash the EMMC to CM7, all status came up as pass and I rebooted. when it came up after the reboot all I got was the "Read Forever" screen.
since then I have read many different posts and tried to boot from the SD...that doesn't work, the screen just stays black
I have tried to boot to CWM to repair or rebuild the EMMC...same outcome
once I remove the SD all I get to is the "Read Forever" screen...
I have read and tried all the steps listed in every post you listed but they all have the same outcome
I have attached a pic of what the screen looks like when it tries to boot.
Fatguy86 said:
Here are the exact steps that I took to get to where I am:
I rooted the stock EMMC with the manual nooter to be able to get the Google Play Market, that worked well and I had access but the Android version was so old that I couldn't install the apps that I was after.
I then attempted to flash the EMMC to CM7, all status came up as pass and I rebooted. when it came up after the reboot all I got was the "Read Forever" screen.
since then I have read many different posts and tried to boot from the SD...that doesn't work, the screen just stays black
I have tried to boot to CWM to repair or rebuild the EMMC...same outcome
once I remove the SD all I get to is the "Read Forever" screen...
I have read and tried all the steps listed in every post you listed but they all have the same outcome
I have attached a pic of what the screen looks like when it tries to boot.
Click to expand...
Click to collapse
Hopefully someone more knowlegeable will look in, this is above my level. The fact that the Read Forever still displays shows that CM did not install correctly, if it's a newer version. You might want to try posting your problem in the same thread that you got the install instructions from.
I have a Nook Color that I've used for some time with CyanogenMod 10.2 with no problems. Last night I was looking at the fixes for Netflix since CM currently has a problem with it, and followed the instructions on XDS for the xposed installer (loading Liquid64's NetflixHackPersist.zip). Things appeared to go fine, and it booted into CM again and I ran the app as instructed. Everything seemed fine up to that point.
But on rebooting, the Nook will not go past the Cyanboot screen. Whether I let it boot by itself, or go to the boot menu and select any of the emmc or SD card options, it just sits there saying it's 'loading xxx' whatever option I've selected and never gets past it. I cannot find a way to force it to boot to the SD card to try anything that way.
I've tried 2 SD cards, reformatted and reburned an 8gb clockwork 3.0.2.8 image to make them bootable...so I don't think it's a card problem.
I'd appreciate some help if anyone knows a way around this. I've had experience with rooting and loading from the SD card, but if it always gets to Cyanoboot and I can't get it to even boot the SD card, I'm stuck. (The 8-reboots trick doesn't seem to work..I've likely reworked too much to still do that.)
Thanks,
JT
jttraverse said:
I have a Nook Color that I've used for some time with CyanogenMod 10.2 with no problems. Last night I was looking at the fixes for Netflix since CM currently has a problem with it, and followed the instructions on XDS for the xposed installer (loading Liquid64's NetflixHackPersist.zip). Things appeared to go fine, and it booted into CM again and I ran the app as instructed. Everything seemed fine up to that point.
But on rebooting, the Nook will not go past the Cyanboot screen. Whether I let it boot by itself, or go to the boot menu and select any of the emmc or SD card options, it just sits there saying it's 'loading xxx' whatever option I've selected and never gets past it. I cannot find a way to force it to boot to the SD card to try anything that way.
I've tried 2 SD cards, reformatted and reburned an 8gb clockwork 3.0.2.8 image to make them bootable...so I don't think it's a card problem.
I'd appreciate some help if anyone knows a way around this. I've had experience with rooting and loading from the SD card, but if it always gets to Cyanoboot and I can't get it to even boot the SD card, I'm stuck. (The 8-reboots trick doesn't seem to work..I've likely reworked too much to still do that.)
Thanks,
JT
Click to expand...
Click to collapse
Try using CWM 6.0.4.7.
hwong96 said:
Try using CWM 6.0.4.7.
Click to expand...
Click to collapse
Hallelujah! I followed your link and (though what I saw suggested trying CWM 5.5.04 for CM 10.2) it WORKED!! It booted to the SD card from Cyanboot, and I had a CM 10.2.1 zip that I was able to install and I'm back in business.
Out of curiosity, is Cyanoboot something unremovable, meaning I can never simply boot straight to an SD card as in the past? It did let me get to the recovery on this SD card, so I guess Cyanoboot was actually working and my problem was something else...but if I simply did a factory reset and wiped everything, would that have removed Cyanoboot as well?
If anyone has suggestions, I'm trying to decide if I'll keep this thing or sell it, so I'm curious what the most fully functional ROM (CM or ?) is considered to be these days, if I didn't put it back to stock?
I've loved this Nook, and only got into the earlier predicament because I thought, if I sold it, a buyer might want to use Netflix...so I was hoping to have it working with a ROM that would please the average Joe user who might hit up Youtube, Netflix, etc.
Thanks for the help!
JT
jttraverse said:
Hallelujah! I followed your link and (though what I saw suggested trying CWM 5.5.04 for CM 10.2) it WORKED!! It booted to the SD card from Cyanboot, and I had a CM 10.2.1 zip that I was able to install and I'm back in business.
Out of curiosity, is Cyanoboot something unremovable, meaning I can never simply boot straight to an SD card as in the past? It did let me get to the recovery on this SD card, so I guess Cyanoboot was actually working and my problem was something else...but if I simply did a factory reset and wiped everything, would that have removed Cyanoboot as well?
If anyone has suggestions, I'm trying to decide if I'll keep this thing or sell it, so I'm curious what the most fully functional ROM (CM or ?) is considered to be these days, if I didn't put it back to stock?
I've loved this Nook, and only got into the earlier predicament because I thought, if I sold it, a buyer might want to use Netflix...so I was hoping to have it working with a ROM that would please the average Joe user who might hit up Youtube, Netflix, etc.
Thanks for the help!
JT
Click to expand...
Click to collapse
If you installed CWM 6.0.4.7 to emmc and want to return to stock go to Leapinlar's tips item A12 on how to return to stock recovery. Or item A15 to flash BN stock recovery using CWM.
http://forum.xda-developers.com/showthread.php?p=25354258#post25354258