New Xoom MZ601 doesn't have USB menu - Xoom General

Computer - Windows Xp 32 bit
I have XOOM MZ601
GAS_ASIA_USAEVRSRTURTIRD_P016
Baseband UCAEVEUB1B8EU034.0R
Build H.6.1-38-9
There is no "usb tethering" at all neither in menu "Wireless and networks" nor in other menus.
When I connect this phone to PC, in device manager it gets detected as MZ601. But it doesn't take any drivers when I press "search automatically".
When select "applications" -> "development" - "usb debugging ON" it is getting detected as MPT
Of cource, I have Motorola_End_User_Driver_Installation_5.4.0_32bit.msi installed.
Can it be detected by the RSD lite in powered ON state?
Is there any way out?
Click to expand...
Click to collapse
Solved by installing Windows media Player 11 LOL

Related

[Q] Help Cannot enter USB debugging mode

Hi all
I'm running Hyperion ROM and merruk kernel
when i connect my phone to my pc, it shows usb connected, touch for mass storage (which works fine)
but not 'usb debugging mode connected' notification
the check box in development menu is ticked
and when i plug in usb "without" checking the box
it automatically checks the box, but it still doesn't show "usb debugging mode connected' notification
my os is windows 8 consumer preview
please help
There's no such notification as "USB Debugging Mode connected". It's only "USB Mass Storage".
Anyways, just check the USB Debugging box in Settings - Applications - Development, and make sure you have the drivers installed in your PC. Then go on to do what you were about to.
||I'm just a PM away for help||
Thanks! I was on my laptop and it didnt have the samsung usb drivers
Works fine now

device not showing up in debug monitor

I have my sg4 plugged into my laptop, but it is not showing up in the android debug monitor. I ran it as administrator, and the device does show up in my computer.
Do you have debugging enabled in Developer options? Make sure you have the right drivers installed otherwise you may need a reboot on both devices
I have the Nexus 7 drivers installed, and the adb interface.
and I do have debugging enabled.
I think that you need the Samsung drivers. The Nexus 7 drivers are different ones. So download them here: http://www.samsung.com/us/support/downloads
They should also be installed if you install Kies.
sniper8752 said:
I have my sg4 plugged into my laptop, but it is not showing up in the android debug monitor. I ran it as administrator, and the device does show up in my computer.
Click to expand...
Click to collapse
There is a well-hidden menu that you may need to access.
Assuming you have developer mode enabled...
- Go to Settings, then Storage
- Click on the menu (top right)
- Select USB computer connection
You'll see 2 boxes:
- Tick 'media device'
I found that if neither box was ticked, I couldn't see my device...
Maybe the first time the dialog says "Allow this computer debugging" appears, you clicked NO.
Try go to Developer options and click "Revoke USB debugging authorizations", and reconnect the device.

Yu Yureka USB Connection Problem

Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
U saved me BRO!!..was tired of using OTH
U saved me BRO!!..was tired of using OTH
Applying all things you said but yureka not connect with computer
USB Computer Connection is still not popping
Hi, I have tried all that is said above, but still I am unable to connect my Yureka to PC. USB Computer Connection is still not popping any options.. Please help
RAUSHAN0704 said:
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
Click to expand...
Click to collapse
well i have tried that but it wont even detect my yureka. IT DOESNT EvEN SHOW A UN RECOGNIZED DEVICE. HOW TO RESOLVe
?
Problem Solved
1. Proceed as Above.
2. Reboot your Phone.
3. Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
Problem Solved...
The problem is not in the phone, or can't be solved by it
Actually you have to do this via pc.
1)search update drivers and find the update device drivers option
2)in other devices find Android and double click
3)click the driver tab
4)click update driver
Worked for me ?????
PC connection Still its not working
RAUSHAN0704 said:
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
Click to expand...
Click to collapse
Hi..
After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected"
can any one please help me ?
---------- Post added at 08:05 AM ---------- Previous post was at 07:59 AM ----------
Sahil Badal said:
1. Proceed as Above.
2. Reboot your Phone.
3. Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
Problem Solved...
Click to expand...
Click to collapse
After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected"
Yureka not connect to PC
[[/B][/B]
RAUSHAN0704 said:
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
Click to expand...
Click to collapse
I have followed all above steps, but not shows USB connection.
I am also getting the same problem "After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected" ", this problem is after getting my replacement handset.
Hi, I have tried all that is said a, but still I am unable to connect my Yureka to PC. USB Computer Connection is still not popping any options.. Please help vikas meena 9694746144
Dear Sir,
As per your instruction i go to the setting but as u written
"Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox. "
after tapping computer connection nothing pop up arises. I can not enable Media Device (MTP)
Please guide me.
Suresh
vertexpac said:
I am also getting the same problem "After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected" ", this problem is after getting my replacement handset.
Click to expand...
Click to collapse
did u get any solution bro????..... i cant copy files to pc and root
---------- Post added at 05:33 AM ---------- Previous post was at 05:30 AM ----------
shadowkill97 said:
well i have tried that but it wont even detect my yureka. IT DOESNT EvEN SHOW A UN RECOGNIZED DEVICE. HOW TO RESOLVe
?
Click to expand...
Click to collapse
did u got any solution bro... i cant connect my yureka to pc. i want to root it. But i cant connect it
USB connection problem
I am also getting the same problem "After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected" ", plz help me
yureka AO 5510
Sir,
My yureka AO 5510 hardbricked and i used emmc image and enter into fastboot mode ( by only pressing power button it can switch on and work) but to flash this is not shown in device manager. I tried with usb driver, adb driver, nothing happend.... and gave to shop and changed its usb port.... but no use....
i can power on it with this memory card or go to fastboot mode.... can not connect to PC.... Please help me....
thank you for your practical guidance, because since so many days and several times I tried to connect with my laptop, last i thought to install some yu drives in my laptop, but this is a very useful points, you are putforth in this moment. once again thank you for the substantial helping tendency you have shown. may proceed it in future to help others,
i am using yu yereka lolipop os and windows 10 x64 pro and tried all method to install drivers but even when i connect my yu yureka ao5510 then it shows me (device disciptor request fail)error code 43.i did all thing from disable driver enforcement and various adb drivers but not success yet..
and when normally connet phone to pc it also not showing the adb option and mtp driver.i aslo tried with different pc but same problem....
plz guy help me!!!!
Got ot developer tools and enable the android debugging.. reboot the mobile
After reboot a pop up window will be opening and asks for disable the android debugging .. disable it in developer tools and then connect the usb cable again . then the pop up will be coming as usual ...and problem got solved
Yureka not connect to any pc
Pc shows popup that the device is malfunctioned.
In device manager it says device dicriptor request failed.
vrishabhv2 said:
i am using yu yereka lolipop os and windows 10 x64 pro and tried all method to install drivers but even when i connect my yu yureka ao5510 then it shows me (device disciptor request fail)error code 43.i did all thing from disable driver enforcement and various adb drivers but not success yet..
and when normally connet phone to pc it also not showing the adb option and mtp driver.i aslo tried with different pc but same problem....
plz guy help me!!!!
Click to expand...
Click to collapse
did you find any solution?

Yu Yureka: Not Recognizing In PC Though Enabling The As MTP- Windows 8.1-32 bit- MTP

Yu yureka- not recognising in pc though enabling the as mtp- windows 8.1-32 bit- mtp
YU YUREKA- NOT RECOGNISING IN PC THOUGH ENABLING THE AS MTP- WINDOWS 8.1-32 BIT- MTP not recognising. I have downloaded and updated all drivers but still not working. pc is not recognising my phone. i have done all the things adb interface kindly help friends
which rom?
try enabling developer options and untick usb debugging , this might help
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy

phone doesnt connect to pc

hi. tried many drivers - and it doesnt connect
doesnt connect as external storage - only charges
and doenst connect with preloader drivers when switched off
in xp and windows 10
what can I do?
Go to your windows device manager then select the mtp device. now rightclick it and select "Update Driver Software" -> "Browse my computer for driver software" -> "Let me pick from a list of devide drivers on my computer" -> remove the tick in front of "Show compatible hardware" -> select "Default MTP-Device" -> now select "MTP-Device" on the right side -> accept the warning.
Youre finished, hope i could help you.

Categories

Resources