In need of some assistance: HTC Shift on Boost Mobile - EVO Shift 4G General

So I have read through at least 50 threads and 10 PDFs to get this far. I also realized that I had to do everything on a 32bit machine since that is the only driver available for the Rant.
So here is a little background on what I have done so far. I rooted the Evo shift easily since it came with the stock 2.2 and installed the newest clockwork and Cyanogen Mod 7 R2. I also updated to the lastest radio (found it here in a thread and it came with an updated WiMax and touchscreen).
I managed to successfully transfer the ESN/MEID. I tried searching and realized it was futile when a new radio that no one knew the locations were. FINALLY, I found someone mentioned a method using EFS and got it to work. After the code 16 error, reactivating on boost mobile, my phone now accepts calls and messages no problem, however 3G is another story.
So some questions:
1. I noticed that my home address is not 0.0.0.0 like most of the guides out there but actually 0.0.0.1 for both profile 1 and 0. Is that okay?
2. My SPI for both profile 1 and 0 were blank and NOT 4D2. Is that okay?
3. My "Rev tunnel preferred" for both profile 1 and 0 were not checked. Is that okay?
4. Should the password for profile 0 and 1 (both HA and AAA) be the same or different? Something I thought I should ask.
Right now, I am going to find a Rom that comes with sense since it has been a pain to use the terminal in order to turn diag on in CM7. Also I am going to try rewriting the 465 and 466 files to the Evo again (I had a rant so 1192 and 1194 were useless essentially BUT I did transfer them over).
Thanks for all the views and help,
Alan

Have you tried THIS thread.

this guy apparently helps people switch their phones over too, i havent done it myself but worth a look:
https://www.facebook.com/groups/294474680575872/

So it seems that my new issue is that my HA and AAA passwords for both profiles refuse to save in QPST.
I downloaded the 465 and 466. 1192 and 1194 refused to write (I have a Rant but not sure if that makes a difference)
I also loaded a sense rom so I could get access to the regular commands.
Is there something I am missing? I entered the MPL password and then enter all the information in the MIP tab and set profile to 0. I click write and get this error
nv_ue_imei_i nv_read only's error
and when I go back to reading the phone when it reboots, nothing has changed.

alansupra94 said:
So it seems that my new issue is that my HA and AAA passwords for both profiles refuse to save in QPST.
I downloaded the 465 and 466. 1192 and 1194 refused to write (I have a Rant but not sure if that makes a difference)
I also loaded a sense rom so I could get access to the regular commands.
Is there something I am missing? I entered the MPL password and then enter all the information in the MIP tab and set profile to 0. I click write and get this error
nv_ue_imei_i nv_read only's error
and when I go back to reading the phone when it reboots, nothing has changed.
Click to expand...
Click to collapse
Just to let everyone know, I finally got the phone to work. 3G is REALLY slow but works. So does the phone and messages.
I actually got it to work using DFS 3.3.0.7 which can be found with searching (cough 4shared cough).
I pretty much swapped the ESN, flashed a completely stock 2.2 rom and then did a reset (##rsn#). After that it started working. Granted, I changed all the settings in DFS 3.3.0.7 before.

Hey alansupra94 can u give me a little bit more help on what to do with dfs? If u could pm me that would be great! I have been trying to get this for a day or so no luck! Thanks
Sent from my PG06100 using XDA

jerebediah said:
Hey alansupra94 can u give me a little bit more help on what to do with dfs? If u could pm me that would be great! I have been trying to get this for a day or so no luck! Thanks
Sent from my PG06100 using XDA
Click to expand...
Click to collapse
Sent you a pm.
Just to let everyone know, I figured out the problem. The Rant was never provisioned to get 3G and refused to on Boost Mobile. Got an Incognito and problem solved.

alansupra94 can you write a guide on this please?

Related

CDMA Sprint HTC Hero to Page Plus?

Kinda new here and I've been searching Google for a good hour to no avail.
I have a Sprint HTC Hero with active service through Sprint that I'm looking to switch to a Page Plus phone number (just purchased a pre-activated Page Plus phone from a local gas station). Main goal is to get the Page Plus service working on the Hero with the Page Plus number as the number for it with text and calling functionality.
I've seen a couple threads where people have said that they flashed their CDMA Hero to a Page Plus ROM and have no problem using it. I cannot find a ROM anywhere that says it's strictly for Page Plus which is making me wonder: Can any ROM be used on Page Plus? And if so, does this mean I switch carriers (Sprint to Page Plus) using another method?
Any help or points into the right direction would be greatly appreciated. I know people often get flamed for "not searching before posting" but I would be eternally grateful for any help that any of you could provide me. Thanks!
Did you ever find an answer to this? I want to do the same thing.
Easiest way would be to go to page plus website and see if the phone can be ported over. If the phone is in a contract with Sprint still you probably wont get your number. I know you can get a locked verizon to page plus but i went through, mingo 1st.
From HowardForums concerning Sprint handsets to page plus:
* Sprint (and Sprint MVNO) handsets are by far, the most difficult. All handset are locked, The OTA activation is incompatible. The MMS system (Picture Mail) is incompatible. IMHO, these handsets are more or less for serious hackers only.
Click to expand...
Click to collapse
change to the spc code to 000000, then manually program the phone.
Click to expand...
Click to collapse
danknee, I assume that by changing the spc code that during this process you are changing the esn code to the page plus phone's eventually correct?
The reason I ask is I may want to try this eventually on the new Virgin Mobile Beyond Talk plan. If I could get my Hero on there I might just do that. Or once the Evo comes out use the Hero to try putting it on there for my son...
I put a Sprint Samsung Instinct on PP using CDMA workshop. I kind of stumbled though it though. Howardforums is a good resource. I recall having to charge the spc, but definitely not the esn. Also, I had to use CDMA workshop to push a Verizon prl unto the. phone. When registering it with PP, I entered I had some other Samsung branded phone(done online).
I was able to use it as a phone but data & picture mails were not.
Good luck.
Changing the spc is just so you can get the phone to update ota. Same step you rake when flashing to cricket. I've done lots of wm phones to cricket. Mms is by far the biggest pain in the ass. From what I understand people have flashed the hero to cricket with working internet, but apps that use the internet do not work. Also, no mms. You will probably be looking at a similar situation here.
Solution
This is in fact quite simple. I recently did it myself. Google Kitty Wireless, and there is a page for manual programming. Download the PRL from that page, put it on your SD card, and click the phone. Type in ##prl# (Im pretty sure this is right, if not google, update prl) and find the file and update the PRL. This will flash your phone and make it use Verizon towers instead of sprint ones. Now that the easy part is done, use Kitty Wireless' activate page, add your ESN, and your phone is on PagePlus, you need to finish though by finish programming your phone.
Now, install aLogCat, phone, ##data#, veiw mode. Go to aLogCat, hit menu, pause, and scroll up to find the MSL code. Now go back, and instead of hitting view mode, hit edit, and type in the MSL code. This will allow you to finish programming it. Now go onto that manual programming page at kitty wireless and finish what they tell you to do.
Any more questions, Ill check back later and try to help.
HTC Hero(sprint) on pageplus
Data is definitely not working. Its an overkill to use HTC hero on pageplus for txt and voice only. I think the refference to "Serious hacker" earlier means making custom baseband firmware. The changes need to accomodate inputting pageplus settings. Or I wonder if anyone tried to load verizon eris baseband firmware on sprint hero.
A few days ago, I have done for activating my Sprint HTC Hero to PagePlus. I ported my phone number, so I didn't change my phone number but my carrier has been changed.. lol.
I posted the instruction to do it. Here you are.
forum.xda-developers.com/showthread.php?t=789751
Also, I got the information about how to make the phone working for data and MMS. I didn't try it because I don't need data. Wifi is around me mostly. If you need, tell me.
------------ I copied the instruction here ------------
I really appreciate you, TpyoKnig.
Now, FINALLY I activated my Sprint HTC Hero to PagePlus. I don't need to waste money for data plan (at least $30/mo). As TpyoKing helped me to activate it, let me post some information I have done for my Hero, in order to help those who want to activate Sprint HTC Hero to PagePlus. If you have any question, tell me. (I'm not a dealer for pageplus. so please don't give me any money.)
Here are what I've got. (I added my experience.)
1) thing you have to have is root for your phone, if you have that then great! Also you need to be running a NON-Froyo Rom (the froyo roms, I've tested thus far) are lacking EPST which will be used later to program the phone. --> My case, I installed NFX-Hero ROM. After I activated my phone to PagePlus, I'm running CM6 ROM. It works fine now.
2) Search the Market (Via WiFi) and download 'MSL reader'
3) Write down that MSL (will need it later)
4) reboot phone
5) download pageplus.prl from a web and put on root of SD card
6) on your phone pull up the dialer (hit the green button) and put in ##775# (##PRL#) and put in your MSL code you got earlier
7) select "update PRL", drop down "Folder" to "SD Card" and push down on your navigation ball and then long press the "menu" key to make your keyboard lower and select pageplus.prl then select "ok", then press your "menu" key and hit commit modification
8) phone will reboot (Congratulations you'r now on Verizon towers!)
9) Get PagePlus to activate phone (eg, contact a local dealer) , tell them you are manually programming a Sprint phone and give them the IMEI and that you need your MIN/MDN and SID. --> In my case, I purchased pageplus from Kittywireless.com. They promptly provide MIN/MDN and SID.
10) on your phone, pull up the dialer and dial ##YOUR6DIGITALMSL# , then select edit mode
11) change Mobile Directory Number (MDN=your new phone number from pageplus) to what is given to you by PP/dealer
12) change MSID to your MIN (Mobile Identification Number) as suplied by PP/Dealer
12) press menu
13) commit changes
I'm really happy.
It Does Work...
DATA and MMS do work I have a Hero on PagePlus and can do both. In fact I've also helped 3 others do that same .
http://www.bpcr.biz/buddy/Android.zip has instructions (not made by me) and APN backup and restore, and the correct APN file needed for PagePlus MMS. Also has instructions on howto get the data settings correct using QPST.
If you have any questions or need help when doing the process PM me or email me [email protected] and I'll contact you back ASAP
Thanks,
Buddy
Thanks guys, got the data working on pageplus using that tutorial.
NP
No Problem . I made it easy . took me a while to get it all working.
Thanks for the helpful information. I'm having some problems getting my Alltel HTC Hero cdma on Page Plus. If you have time, can you take a look at the question I posted as a thread? It's titled "prl update for page plus on alltel htc hero cdma".
Thanks
i am attempting to change my HTC Hero (Sprint) to PagePlus...does the device has to be already activated with sprint in order to work. (it is currently deactivated no serivce)
daskydivr said:
i am attempting to change my HTC Hero (Sprint) to PagePlus...does the device has to be already activated with sprint in order to work. (it is currently deactivated no serivce)
Click to expand...
Click to collapse
no it doesn't that is not a requirement. just follow the directions that I've linked to: http://www.bpcr.biz/buddy/Android.zip
I have a few questions for everyone. I currently have about a year left on my sprint contract. I am willing to buy it out and switch to page plus, but I would like to save money on the phones. With sprint I have 2 HTC Heros. If I can get them to work that would save a bit of $$.
Question about procedure: In the directions (in zip file) it says they are for EVO, will it still work on Hero? Next question, in the directions it says "THIS TUTURAL IS ASSUMING THAT YOU ARE ALREADY BASIC FLASHED!". What does that mean? Is that the basic rom? My Hero is rooted and running CM6. My wife's Hero is stock sprint (1.5 I think).
Question about numbers (if you know...if not no biggie): I want to port my numbers from sprint to page plus.
Thanks in advance for any help!!!
teedybeedy said:
Question about numbers (if you know...if not no biggie): I want to port my numbers from sprint to page plus.
Thanks in advance for any help!!!
Click to expand...
Click to collapse
There was supposed to be more to that: I want to port my numbers from sprint to page plus. Should I do the flashing to page plus procedure first, then call page plus and get them to activate it? Or is the flashing procedure something I do after I join page plus? All in all, I want to keep my phone numbers, they might be worth more to me than the phone
teedybeedy said:
There was supposed to be more to that: I want to port my numbers from sprint to page plus. Should I do the flashing to page plus procedure first, then call page plus and get them to activate it? Or is the flashing procedure something I do after I join page plus? All in all, I want to keep my phone numbers, they might be worth more to me than the phone
Click to expand...
Click to collapse
Basic flash is what I've already outlined, in the previous page, loading the PRL and inputting your MDN/MIN to the phone , the rest of the tutorial is for acquired the beloved 3g and yes it can work on ANY HTC device, Hero/Evo
HTC Hero Sprint to PagePlus instructions
Does anyone still have the conversion instructions for Sprint HTC Hero handy? I'm trying to convert my HTC Hero from Sprint to PagePlus but this link does not work any more.

[VIDEO] Samsung Captivate IPSec VPN How-To

All links pulled due to XDA Request after an XDA member complained I was only out for profits to a moderator on a few products I have. Due to the fact I link to a product or two and a few other things in many videos, I was asked to pull any content relating to this.
I will still be offering all this great material at my website. Just go to google and search for MobileTechVideos.
I really think these how-to videos should be in Q&A (or general) instead of development.
Sent from my brain using Thumbs 2.0.
glitterballs said:
I really think these how-to videos should be in Q&A (or general) instead of development.
Sent from my brain using Thumbs 2.0.
Click to expand...
Click to collapse
I'd probably agree. I put that line in their for a MOD to move them if applicable. Now that I decided to dive into this, if a MOD moves this, might you be able to join my ROM flashing video with this one?
Thanks.
My company uses Cisco VPN along with RSA SecurID.
I've tried other "solutions" in the past with no success.
Will this process work in my situation?
I have access to all the settings from a .pcf configuration file.
When I had an iPhone, VPN worked perfectly (not that I'd go back to an iPhone just for that ).
The VPN Connections applications allows for a secure token so I think it may work. The SecureID just gives you a token correct? And then you input it for access?
If you watch near the end of video 2 I show you that application and there is clearly a field for token input. You should not need the .pcf file for the phone. I would think you would just input the current token each time.
I tried it and the connection fails every time.
Went through the process twice and followed directions to the letter.
I also tried the check box "Password + Token Digits" and that did not work either.
I'm using a 2.2 ROM currently but I think I'll put my phone back to stock and try again with 2.1.
Your video is excellent, by the way, and extremely easy to follow.
Thank you for compliments. Did you verify tun module was running using the lsmod command from a shell?
connexion2005 said:
Thank you for compliments. Did you verify tun module was running using the lsmod command from a shell?
Click to expand...
Click to collapse
Yes, tun was definitely running.
thank you much, works well.
jwolfburg said:
thank you much, works well.
Click to expand...
Click to collapse
Glad it was able to help you! I know I would have loved this info 6 months ago as I was figuring it out. If you are looking for a good RDP app, then use RemoteRDP. I'm using the $20 enterprise edition and it's amazing. They have cheaper versions as well with a few less bells and whistles options.
Now I'm just trying to crack DNS issues with Android not resolving hostnames of machines when VPN'd or on a WIFI network.
I am getting a device or resource busy when I do insmod android22tun.ko
I am running auxura and I skipped the rooting process as I am obviously already rooted.
Any ideas anyone?
I suppose you could try modprobe instead of insmod just to see. It could also very well be ROM dependent and something with this particular tun.ko file could be incompatible. There are many different tun.ko files for different kernels.
connexion2005,
I just wanted to thank you for the awesome step-by-step tutourial on getting my phone connected to IPSec VPN. I too am a IT Admin and recently got my phone with the objective in mine to remotely manage infraustruture. Your instructions are to the point and didn't leave much to guessing.
BTW: at the end of the video you mention the gscript tool to run the tun.ko for reloading. Shouldn't you actually had said adroid21tun.ko? That's what works.
mrjazze said:
connexion2005,
I just wanted to thank you for the awesome step-by-step tutourial on getting my phone connected to IPSec VPN. I too am a IT Admin and recently got my phone with the objective in mine to remotely manage infraustruture. Your instructions are to the point and didn't leave much to guessing.
BTW: at the end of the video you mention the gscript tool to run the tun.ko for reloading. Shouldn't you actually had said adroid21tun.ko? That's what works.
Click to expand...
Click to collapse
I mean the technical name of the vpn module on linux based equipment is tun.ko so that's what I went with. I understand that may be confusing now. Whatever the module is named is what needs to be loaded. So you could call it mobiletechvideosdotcom.ko and that's what you'd load...lol. Thanks for the compliments!
Your very welcome. I think i have watched all your videos and I have to say great job.
sent from my Samsung Captivate using XDA app.
connexion2005,
It seems I have run into a problem. I have been able to connect to our ASA a few times already, but when I just tried today it fails. After investigating, my script to load the android21tun.ko fails with error "init_module 'android21tun.ko' failed (file exists). I even get the failure after reboot phone. Do you have any suggestions.
PS: Out of curiosity, you suggested RemoteRDP, have you tried PocketCloud? I like it so much I will pay the $14.99 for full version.
Thank you. This worked like a charm.
mrjazze said:
connexion2005,
It seems I have run into a problem. I have been able to connect to our ASA a few times already, but when I just tried today it fails. After investigating, my script to load the android21tun.ko fails with error "init_module 'android21tun.ko' failed (file exists). I even get the failure after reboot phone. Do you have any suggestions.
PS: Out of curiosity, you suggested RemoteRDP, have you tried PocketCloud? I like it so much I will pay the $14.99 for full version.
Click to expand...
Click to collapse
I have not used PocketCloud but RemoteRDP is absolutely phenomenal. Is this occuring even after a reboot? Perform an lsmod from a terminal and check to see if the tun module is running. I'm not sure why this would happen. May have to uninstall everything including the tun and re-perform the steps.
I did get it to work again. Strangely, it was after receiving a phone call that the module would load. Thanks again for your assistance.
Well that's good. I can't explain any bugs as my dev work only extends so far!

How to get 3g on boostmobile guide!!!

Disclaimer
The following guide is for educational purposes only, it is not intended to start, continue and or conducting illegal activities such as esn/meid changes that do not belong to you and or invasion of private network data, anything that can be proven as a means to obtain services that you have not paid but not limited to extending the human knowledge and testing our capacity to evolve into a better human race than what we are today…. LOL …..is true…
DURING THIS PROCESS I WAS USING WIN VISTA HP 32 BITS issues with drivers signatures on 64 builds.
Required software and Tools
QPST build 2.15 no exceptions
CDMAWORKSHOP 3.5 or above-please use paid version to support developers. If you don’t have the funds and or are cheap there is a cracked version floating around the web.
BOOSTMOBILE INCOGNITO- not really true any phone capable of receiving 3g signals and that you are able to read items 465,466,1192,1194 will work fine as long as the device is already in service with the network of your choice. However this one is intended on the boost/the now network prepaid bootlegged network.
Incognito win vista 32 drivers
Samsung Fascinate Drivers
STEPS FOR THE INCOGNITO DATA EXTRACTION ETC.
--1—after you have successfully installed the Incognito drivers please connect the phone. Launch CWS and connect to the dial port. Read the phone and head to the Security tab.
Click on SPC/lock and pull the curtain and select Universal Ram once done search for incognito. Send the spc once is retrieve and read and save NAM to a folder of your choice. Name it whatever you want, next head to other tab and read PRL and also save it to same folder. *found out the phone will work better with the PRL the incognito was working with. Don’t write anything from sprint may dropped your signal. I know is weird does not makes sense but feel free to explore.
Because of sprint prl it would override my data info and had to restart the process again. My experience. Now access the Memory tab under NV items and read the following numbers 465,466,1192,1194 each one individually. Your beginning address is the same as your end address for example: starting 465-465 do not do 0465-0465. Won’t work and may brick your fascinate once you write, repeat the process for each one and save with whatever name, preferably as the number item you are using. *very important* now we want to manually copy down your user id. On the phone dial ##3282# it will bring you to a menu insert your spc and access user name. please copy exactly.
Turn off your incognito and put it away. Take the battery out you don’t want someone else turning it on by accident. It will scramble your data settings on the fascinate.
PLEASE MAKE SURE THAT YOU DO A FACTORY RESET ON THE FASCINATE. We don’t want any bits of information from a previous setting creating conflict with the new data.
At this point your Samsung Fascinate have acquired a new Dec number that was done that you don’t know, want to know or talk about. Main point is that you did not do it.
After reset phone will want to be activated. To bypass please dial *#83786633 and the Home Key
Now you want to enable the hidden menu. *#22745927 it will take you to a screen and select enable hidden menu.
DIAL ##3282# or **3282 or ##3282 which ever works for you send spc and change the user id on the phone to the one that you wrote down earlier. REBOOT
Depending on the rom you are using the DIAG option is under WIRELESS & NETWORK please select it and now your pc will be installing the required drivers if you have not installed them before.
Launch CWS and select port, read info and head to Security Tab. You must send the 16 digit password in order for all data to write correctly. If you don’t know this number here it is 2010031619780721. By default the password is 000000 but it will not work until you have enable hidden menu. Lets continue.
Once you have sent the spc please access the NAM and load the one you previously saved from the incognito, and click write.
Now do the same thing for the PRL on the Other tab. Exit cws and reboot, after reboots reconnect send 16 digits, you could do the 000000 but for some reason I feel that it does not writes everything correctly.
Head to the NV items section and Hit Write, it may say that you may needs spc first just click yes and load the 1st nv item starting with 465 from the file you saved them earlier in an ascending pattern. One all 4 items have been written exit cws and wait for it to reboot. Disable DIAG MODE. After the phone has finish loading the sd card etc if the 3g signal does not start after 10-15 seconds the following applies. Most likely you will need the next step.
Launch QPST 2.15 if you do not have cws you need to install QPST 2.7.323 due to the fact that under 2.15 the fascinate will appear under W5-FFA6250-T with limited tabs and NAM and MIP is not available.
Once online with QPST 2.15 we need to figure out the PPP config tab. Read the info on the phone and replace with the following data. This is what works with me whether on boost or Sprint alone
The following are horizontally just follow the name on each section,
-RM- ppp parameters
Config tries—Request timeout—Config NAK tries—Terminate tries—Request Time out—Comp settings—PPP Auth
20 1000 3 2 3000 5 3000
20 1000 3 3 1000 Disable
20 1000 3 3 1000 Ignored
User id do not high light it uncheck required pw Under PPP only click it but not check
-UM- same as above follow pattern
User ID this is funny and it should not work but it does. [email protected]
All lower case please.
Make sure that all is lower case. Also the password just click the box don’t check it leave it blank
Optimized Dormant Handoff box Checked do not click the 1xEVDO
-AN-
Userid
[email protected]@hcm.sprintpcs.com
Hit first save the Qpst file and write.
The phone will reboot but do not disconnect it until it has completely loaded all options. Disable Diag mode and with in 10 to 15 seconds you should have 3g. I was able to obtain 800-1350 kbs with speedtest.net
Note if you have another phone and want the data from the other phone the AN user id has to be same one that you program the very first time. Yes I know it does not make sense. But it does works. I hope this works for me as it has for me. It works for me and have reprogram various.
Any new news on this. Have a friend interested in this.
Sent from my SCH-I500 using Tapatalk
i would love to do this too. a write up would be highly appreciated man. I'm glad you got it to work!
Sent from my SCH-I500 using XDA Premium App
Okay, how did you sneak a Verizon phone onto a Sprint MNVO network?
obonilla30 said:
Disclaimer
The following guide is for educational purposes only, it is not intended to start, continue and or conducting illegal activities such as esn/meid changes that do not belong to you and or invasion of private network data, anything that can be proven as a means to obtain services that you have not paid but not limited to extending the human knowledge and testing our capacity to evolve unto a better human race than what we are today…. LOL …..is true…
DURING THIS PROCESS I WAS USING WIN VISTA HP 32 BITS issues with drivers signatures on 64 builds.
Required software and Tools
QPST build 2.15 no exceptions
CDMAWORKSHOP 3.5 or above-please use paid version to support developers. If you don’t have the funds and or are cheap there is a cracked version floating around the web.
BOOSTMOBILE INCOGNITO- not really true any phone capable of receiving 3g signals and that you are able to read items 465,466,1192,1194 will work fine as long as the device is already in service with the network of your choice. However this one is intended on the boost/the now network prepaid bootlegged network.
Incognito win vista 32 drivers
Samsung Fascinate Drivers
STEPS FOR THE INCOGNITO DATA EXTRACTION ETC.
--1—after you have successfully installed the Incognito drivers please connect the phone. Launch CWS and connect to the dial port. Read the phone and head to the Security tab.
Click on SPC/lock and pull the curtain and select Universal Ram once done search for incognito. Send the spc once is retrieve and read and save NAM to a folder of your choice. Name it whatever you want, next head to other tab and read PRL and also save it to same folder. *found out the phone will work better with the PRL the incognito was working with. Don’t write anything from sprint may dropped your signal. I know is weird does not makes sense but feel free to explore.
Because of sprint prl it would override my data info and had to restart the process again. My experience. Now access the Memory tab under NV items and read the following numbers 465,466,1192,1194 each one individually. Your beginning address is the same as your end address for example: starting 465-465 do not do 0465-0465. Won’t work and may brick your fascinate once you write, repeat the process for each one and save with whatever name, preferably as the number item you are using. *very important* now we want to manually copy down your user id. On the phone dial ##3282# it will bring you to a menu insert your spc and access user name. please copy exactly.
Turn off your incognito and put it away. Take the battery out you don’t want someone else turning it on by accident. It will scramble your data settings on the fascinate.
PLEASE MAKE SURE THAT YOU DO A FACTORY RESET ON THE FASCINATE. We don’t want any bits of information from a previous setting creating conflict with the new data.
At this point your Samsung Fascinate have acquired a new Dec number that was done that you don’t know, want to know or talk about. Main point is that you did not do it.
After reset phone will want to be activated. To bypass please dial *#83786633 and the Home Key
Now you want to enable the hidden menu. *#22745927 it will take you to a screen and select enable hidden menu.
DIAL ##3282# or **3282 or ##3282 which ever works for you send spc and change the user id on the phone to the one that you wrote down earlier. REBOOT
Depending on the rom you are using the DIAG option is under WIRELESS & NETWORK please select it and now your pc will be installing the required drivers if you have not installed them before.
Launch CWS and select port, read info and head to Security Tab. You must send the 16 digit password in order for all data to write correctly. If you don’t know this number here it is 2010031619780721. By default the password is 000000 but it will not work until you have enable hidden menu. Lets continue.
Once you have sent the spc please access the NAM and load the one you previously saved from the incognito, and click write.
Now do the same thing for the PRL on the Other tab. Exit cws and reboot, after reboots reconnect send 16 digits, you could do the 000000 but for some reason I feel that it does not writes everything correctly.
Head to the NV items section and Hit Write, it may say that you may needs spc first just click yes and load the 1st nv item starting with 465 from the file you saved them earlier in an ascending pattern. One all 4 items have been written exit cws and wait for it to reboot. Disable DIAG MODE. After the phone has finish loading the sd card etc if the 3g signal does not start after 10-15 seconds the following applies. Most likely you will need the next step.
Launch QPST 2.15 if you do not have cws you need to install QPST 3.11.323 due to the fact that under 2.15 the fascinate will appear under W5-FFA6250-T with limited tabs and NAM and MIP is not available.
Once online with QPST 2.15 we need to figure out the PPP config tab. Read the info on the phone and replace with the following data. This is what works with me whether on boost or Sprint alone
The following are horizontally just follow the name on each section,
-RM- ppp parameters
Config tries—Request timeout—Config NAK tries—Terminate tries—Request Time out—Comp settings—PPP Auth
20 1000 3 2 3000 5 3000
20 1000 3 3 1000 Disable
20 1000 3 3 1000 Ignored
User id do not high light it uncheck required pw Under PPP only click it but not check
-UM- same as above follow pattern
User ID this is funny and it should not work but it does. [email protected]
All lower case please.
Make sure that all is lower case. Also the password just click the box don’t check it leave it blank
Optimized Dormant Handoff box Checked do not click the 1xEVDO
-AN-
Userid
[email protected]@hcm.sprintpcs.com
Hit first save the Qpst file and write.
The phone will reboot but do not disconnect it until it has completely loaded all options. Disable Diag mode and with in 10 to 15 seconds you should have 3g. I was able to obtain 800-1350 kbs with speedtest.net
Note if you have another phone and want the data from the other phone the AN user id has to be same one that you program the very first time. Yes I know it does not make sense. But it does works. I hope this works for me as it has for me. It works for me and have reprogram various.
Click to expand...
Click to collapse
Im sorry guys for not posting earlier. I was out of it but ..... im ok now. I hope this guide will help you or at least give you and idea.
obonilla30 said:
Disclaimer
The following guide is for educational purposes only, it is not intended to start, continue and or conducting illegal activities such as esn/meid changes that do not belong to you and or invasion of private network data, anything that can be proven as a means to obtain services that you have not paid but not limited to extending the human knowledge and testing our capacity to evolve into a better human race than what we are today…. LOL …..is true…
DURING THIS PROCESS I WAS USING WIN VISTA HP 32 BITS issues with drivers signatures on 64 builds.
Required software and Tools
QPST build 2.15 no exceptions
CDMAWORKSHOP 3.5 or above-please use paid version to support developers. If you don’t have the funds and or are cheap there is a cracked version floating around the web.
BOOSTMOBILE INCOGNITO- not really true any phone capable of receiving 3g signals and that you are able to read items 465,466,1192,1194 will work fine as long as the device is already in service with the network of your choice. However this one is intended on the boost/the now network prepaid bootlegged network.
Incognito win vista 32 drivers
Samsung Fascinate Drivers
STEPS FOR THE INCOGNITO DATA EXTRACTION ETC.
--1—after you have successfully installed the Incognito drivers please connect the phone. Launch CWS and connect to the dial port. Read the phone and head to the Security tab.
Click on SPC/lock and pull the curtain and select Universal Ram once done search for incognito. Send the spc once is retrieve and read and save NAM to a folder of your choice. Name it whatever you want, next head to other tab and read PRL and also save it to same folder. *found out the phone will work better with the PRL the incognito was working with. Don’t write anything from sprint may dropped your signal. I know is weird does not makes sense but feel free to explore.
Because of sprint prl it would override my data info and had to restart the process again. My experience. Now access the Memory tab under NV items and read the following numbers 465,466,1192,1194 each one individually. Your beginning address is the same as your end address for example: starting 465-465 do not do 0465-0465. Won’t work and may brick your fascinate once you write, repeat the process for each one and save with whatever name, preferably as the number item you are using. *very important* now we want to manually copy down your user id. On the phone dial ##3282# it will bring you to a menu insert your spc and access user name. please copy exactly.
Turn off your incognito and put it away. Take the battery out you don’t want someone else turning it on by accident. It will scramble your data settings on the fascinate.
PLEASE MAKE SURE THAT YOU DO A FACTORY RESET ON THE FASCINATE. We don’t want any bits of information from a previous setting creating conflict with the new data.
At this point your Samsung Fascinate have acquired a new Dec number that was done that you don’t know, want to know or talk about. Main point is that you did not do it.
After reset phone will want to be activated. To bypass please dial *#83786633 and the Home Key
Now you want to enable the hidden menu. *#22745927 it will take you to a screen and select enable hidden menu.
DIAL ##3282# or **3282 or ##3282 which ever works for you send spc and change the user id on the phone to the one that you wrote down earlier. REBOOT
Depending on the rom you are using the DIAG option is under WIRELESS & NETWORK please select it and now your pc will be installing the required drivers if you have not installed them before.
Launch CWS and select port, read info and head to Security Tab. You must send the 16 digit password in order for all data to write correctly. If you don’t know this number here it is 2010031619780721. By default the password is 000000 but it will not work until you have enable hidden menu. Lets continue.
Once you have sent the spc please access the NAM and load the one you previously saved from the incognito, and click write.
Now do the same thing for the PRL on the Other tab. Exit cws and reboot, after reboots reconnect send 16 digits, you could do the 000000 but for some reason I feel that it does not writes everything correctly.
Head to the NV items section and Hit Write, it may say that you may needs spc first just click yes and load the 1st nv item starting with 465 from the file you saved them earlier in an ascending pattern. One all 4 items have been written exit cws and wait for it to reboot. Disable DIAG MODE. After the phone has finish loading the sd card etc if the 3g signal does not start after 10-15 seconds the following applies. Most likely you will need the next step.
Launch QPST 2.15 if you do not have cws you need to install QPST 3.11.323 due to the fact that under 2.15 the fascinate will appear under W5-FFA6250-T with limited tabs and NAM and MIP is not available.
Once online with QPST 2.15 we need to figure out the PPP config tab. Read the info on the phone and replace with the following data. This is what works with me whether on boost or Sprint alone
The following are horizontally just follow the name on each section,
-RM- ppp parameters
Config tries—Request timeout—Config NAK tries—Terminate tries—Request Time out—Comp settings—PPP Auth
20 1000 3 2 3000 5 3000
20 1000 3 3 1000 Disable
20 1000 3 3 1000 Ignored
User id do not high light it uncheck required pw Under PPP only click it but not check
-UM- same as above follow pattern
User ID this is funny and it should not work but it does. [email protected]
All lower case please.
Make sure that all is lower case. Also the password just click the box don’t check it leave it blank
Optimized Dormant Handoff box Checked do not click the 1xEVDO
-AN-
Userid
[email protected]@hcm.sprintpcs.com
Hit first save the Qpst file and write.
The phone will reboot but do not disconnect it until it has completely loaded all options. Disable Diag mode and with in 10 to 15 seconds you should have 3g. I was able to obtain 800-1350 kbs with speedtest.net
Note if you have another phone and want the data from the other phone the AN user id has to be same one that you program the very first time. Yes I know it does not make sense. But it does works. I hope this works for me as it has for me. It works for me and have reprogram various.
Click to expand...
Click to collapse
followed word for word still no data what rom are you using and what radio
nick cannon said:
followed word for word still no data what rom are you using and what radio
Click to expand...
Click to collapse
You need to be using a 2.1 rom with dial up networking mode or use 2.2 with the settings mod for it to be able to be read by QPST. and you need TWO versions of QPST for the settings to stick on the fascinate. after you've cloned the incognito make sure u turn that **** OFF!!! forever... just break that **** forreal because if not it will mess up the data settings (or get u in trouble for cloning since its "illegal"). This works the same as flashing to Cricket, as i know because i've flashed both of mine to cricket the month after we switched from t-mobile because of those two bs 200 dollar phone bills (now 113 for two lines). we dont use that much mobile data right now because we have WiFi at home.
My friend did this on his epic and it works flawlessly. I was actually gonna sell my fassy for 200 (i can get a new one from this store right around the corner to flash for 200). So if anyone wants a fascinate, i'll sell them it for 200, so i can get a epic on boost, and 35 a month with shrinkage plan =O
Really, you should look on the flashing the fascinate to cricket thread its much less jumbled. just take the incognito settings plug them in to qpst in the fascinate (exactly) and then the data "should" work. thats what he did lol... i was there the last 30 minutes before he got it actually working. PM me and i can put u on with him if you need help.
Wait a second, so I can take a boost phone and run it on the vzw network? Data and all? For pennies on the dollar?
Sent from my SCH-I500 using tapatalk
Nick were you able to make it work? it should work mostly in any rom. better on 2.2 faster 3g. I clocked that phone at 1450 kbps. My little brother has it now. no problems at all. let me know if you need help
NO not on the VZW but on boost or cricket or any other company.
how to get 3g on boost
akaine2001 said:
You need to be using a 2.1 rom with dial up networking mode or use 2.2 with the settings mod for it to be able to be read by QPST. and you need TWO versions of QPST for the settings to stick on the fascinate. after you've cloned the incognito make sure u turn that **** OFF!!! forever... just break that **** forreal because if not it will mess up the data settings (or get u in trouble for cloning since its "illegal"). This works the same as flashing to Cricket, as i know because i've flashed both of mine to cricket the month after we switched from t-mobile because of those two bs 200 dollar phone bills (now 113 for two lines). we dont use that much mobile data right now because we have WiFi at home.
My friend did this on his epic and it works flawlessly. I was actually gonna sell my fassy for 200 (i can get a new one from this store right around the corner to flash for 200). So if anyone wants a fascinate, i'll sell them it for 200, so i can get a epic on boost, and 35 a month with shrinkage plan =O
Really, you should look on the flashing the fascinate to cricket thread its much less jumbled. just take the incognito settings plug them in to qpst in the fascinate (exactly) and then the data "should" work. thats what he did lol... i was there the last 30 minutes before he got it actually working. PM me and i can put u on with him if you need help.
Click to expand...
Click to collapse
you will get that but the 1x signal which is bull****, I am running this thing faster than the evo on Sprint 3g mode, we are actually talking about true 3g not your typical 400-800 kbps bs. cricket is different and much easier, cricket oass cricket etc bs, so simple even a cave man can do it. lol....
Is this usable on GB? I think cm7 breaks data ...
Have you tested on a GB rom?
Sent from my SCH-I500 using XDA App
This guide followed to the t works perfectly for the mesmerize as well... just thought id share.
I hate to revive a dead thread, but can this guide be used to flash a fascinate onto sprint as well? For educational and recreational purposes of course.
It should same steps.
I might have to try this. Verizon is robbing me
Sent from my SCH-I500 using XDA App
nice quide , it was really helpful , i have the fascinate working with 1x speed on boos which is suprisingly fast , i cant get mms to work though , any ideas .
I have 2 fascinates over on boost, I have not tested out the mms at all but I have full 1x and 3G speeds. if you dig around for boost mms on other phones for you will find things like
`` Dial ##3282#, edit and enter your epic’s spc, scroll down and on change the MMSC URL to “mm.myboostmobile.com” ``
and
``
MMSC: http://mm.myboostmobile.sprintpcs.com
MMS proxy: I left mine blank
MMS Port: 80
``
I used the later settings, but as I said, I have not tested my mms yet..
I have talk and text working fine,and I have the 3 g Icon but no internet .........can some one. please me
Sent from my PG86100 using Tapatalk

[Q] Still not getting Internet with Android

Hi:
I am loving my HTC HD2 running Windows Mobile and Android. I am using the following latest builds which work very well:
AmericanAndroid
MCCMBoxMax
and another which doesn’t come to my mind.
The only thing that is keeping me from a perfect experience is getting internet connection while in Android.
1. In Android OS, If I am connected to WIFI I get perfect internet at home or anyplace else where there is WIFI
2. In Windows Mobile, if there is no WIFI, I can connect to internet via my cell phone connection. I guess this is called data connection. I seem be having trouble doing this regardless of what Android build I use. Is there some setting I should be using in Android to get this to work? I’m almost certain I have the Mobile network setting checked. If there is some other setting, I must be missing it
I don't get any error messages, just that there is no internet connection when I goto a web page or try to goto Market.
Any help with this issue would be greatly appreciated, and thank you for your help in advance!
Chaz
There are many reasons why your data connection might not be working well because of.
First, your APN Settings may not be correctly set.
Second, in case you're running off NAND and you're using cLK with rmnet.
Third, your phone couldn't resolve the DNS server thus giving you no connectivity.
To fix the:
First, check your settings.
Second, Enable ppp instead of rment.
Third, editing the build.prop in your device.
after opening it, look for DNS1 and DNS2 .
Set DNS1 (or Primary DNS) to: 8.8.8.8
Set DNS2 (or Alternative DNS) to : 8.8.4.4
build.prop is located in system folder in your device.
Reboot, and check if it is working.
Well, maybe I mistated....It doesn't connect to anything while booted in Android. The only so far to get internet connection is thru a WIFI connection. If there is no WIFI then I get nothing. With WINMO 6.x I get data, but not with Android.
Will those instructions you gave still work? If so, I will try it after work.
Thank You!
You mean you see the "H", "3G", "E" or "G" but you can't get internet. or you don't even see them?
what does it say when you turn on Data connection?
Ah...maybe thats the problem. I get 5 bars, but those letters are no where to be found. When I'm on the WINMO side, I get those letters.
Wait....as I'm typing this, I just saw the letter H with up and down arrows below it. What does that mean?
kawazaki said:
There are many reasons why your data connection might not be working well because of.
First, your APN Settings may not be correctly set.
Second, in case you're running off NAND and you're using cLK with rmnet.
Third, your phone couldn't resolve the DNS server thus giving you no connectivity.
To fix the:
First, check your settings.
Second, Enable ppp instead of rment.
Third, editing the build.prop in your device.
after opening it, look for DNS1 and DNS2 .
Set DNS1 (or Primary DNS) to: 8.8.8.8
Set DNS2 (or Alternative DNS) to : 8.8.4.4
build.prop is located in system folder in your device.
Reboot, and check if it is working.
Click to expand...
Click to collapse
How do you enable ppp?
Sent from my HTC HD2 using XDA App
That means you're now connected to the internet, you probably have network select set on "WCDMA Only" and your area has insufficient 3G coverage. Just set it to "WCDMA/GSM Auto" .
Gunblade77 said:
How do you enable ppp?
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
Depends on your build, reading the OP of your build will definitely give you the answer but in most cases you can do so by editing the config.txt file on your sd card (create if not there) .. also keep in mind that not all builds support config.txt nor PPP. Refer to your build's thread. you also have to have a compatible kernel.
I'm using HyperDroid GBX v12, couldn't find anything on the rom's thread. Although I did find a ppp.txt right next to my build.txt in my system folder. Does this mean it is enabled?
Sent from my HTC HD2 using XDA App
I'm not really sure, but you could try making a txt file on the root of your sd card and name it "config.txt" and write in it the following:
Code:
ppp_mode=1
Then reboot your phone with sd card on, and see if it works.
chazperx said:
Hi:
I am loving my HTC HD2 running Windows Mobile and Android. I am using the following latest builds which work very well:
AmericanAndroid
MCCMBoxMax
and another which doesn’t come to my mind.
The only thing that is keeping me from a perfect experience is getting internet connection while in Android.
1. In Android OS, If I am connected to WIFI I get perfect internet at home or anyplace else where there is WIFI
2. In Windows Mobile, if there is no WIFI, I can connect to internet via my cell phone connection. I guess this is called data connection. I seem be having trouble doing this regardless of what Android build I use. Is there some setting I should be using in Android to get this to work? I’m almost certain I have the Mobile network setting checked. If there is some other setting, I must be missing it
I don't get any error messages, just that there is no internet connection when I goto a web page or try to goto Market.
Any help with this issue would be greatly appreciated, and thank you for your help in advance!
Chaz
Click to expand...
Click to collapse
I'd advise you to use a permanent Android Version, such as BOYPPC (which is the best in my mind)!
Otherwise install a newer SD-Android Version, and turn on the data connection in settings! Should work.
If there appears a E, G, 3G or H in your task bar, then u have internet connection!
Thank you for all your help and suggestions. I just installed:
[08 JULY][SD/MAGDLR] MccMBoxmaX GS V8 Gingerbread
And I finally got the Data to work. I don't know what happened, but it working. I am so happy I waited a year to by the HD2 Telstra.....Thanks again!
chazperx said:
Thank you for all your help and suggestions. I just installed:
[08 JULY][SD/MAGDLR] MccMBoxmaX GS V8 Gingerbread
And I finally got the Data to work. I don't know what happened, but it working. I am so happy I waited a year to by the HD2 Telstra.....Thanks again!
Click to expand...
Click to collapse
I m having same problem tried Following SD builds:
1.BoxmaX KS.6.5.SD.Tyr5
2.Android 2.2 superram
but no use.. .actually my problem is i am unable to save APN settings...the moment i click save button it doesnt show up even though i filled up all required fields..anyways i hv downloaded above mentioned rom just now...but can you let me know what exactly u did ?...i mean anything else u did other than just applying above mentioned ROM ..which i should do too...
any help on this is highly appreciated!!!
Thanks

Samsung Flow not working, help needed

Hello,
I just downloaded Samsung Flow through Windows Store and now when I try to open it it says that the computer does not meed minimum system requirements to run Samsung Flow... I have MSI GT72 laptop which is new and running original Windows 10 Home. I have latest update that enabled installing Samsung Flow already installed...
Thank you very much for all your help and answers, I really appreciate it.
Same goddamn problem here as well.
S7 Edge + ASUS ROG notebook. Both updated up the wazoo.
My Windows 10 version is 15063.413 which is exactly the minimum threshold. But I still get the same error.
When has this been released for all PC's? I bought a bt stick but until now wasn't able to even download it... Have to check later to see if it's now online
---------- Post added at 01:17 PM ---------- Previous post was at 01:04 PM ----------
Ok, I can now install it. Seems you need a tpm module. On the Samsung g website you can download a driver. On trying to install it, I get an error concerning tpm...
Hey there. I tri3d the same thing. The TPM chip is hard wired to the motherboard. If your PC didn't come with it. You can't use Samsung Flow.
More Desktops and Business Pcs have the TPM chip, I work in IT so I see them on Lenovo and Dell PCs for business all the time. It pissed me off when it wouldn't work on my HP 15 as well due to the same error.
I have seen some people are able to emulate TPM via software, but that is way above my level of expertise
I can't make my setup work either. I actually have TPM enabled and working using a Dell Latitude E7440. The app and driver installed fine but when I pair my devices via the Flow app the pairing does not stick. I enabled PIN authentication in Windows as well and nothing. Every time I click on "Register Device" I get a prompt to re-authenticate the Bluetooth connection itself. The handshake does not happen and I am not prompted for a PIN. Nice try by Samsung but major fail in implementation.
FWIW, I have a Lenovo Yoga 900 and it works flawlessly. I'm actually extremely surprised but apart from being able to swipe the fingerprint sensor on S8 to unlock Windows 10 it has a window that mirrors your phone notifications so you can action/respond on your computer. Also there's a way to send files from the computer to the phone by dragging and dropping. Overall it's not bad at all
OMG port to LG G5 xD
I updated my windows and now having the same problem. It Samsung flow was working on my computer now it tells me it can't
FWIW, I was receiving the same error till I enabled bluetooth on the laptop.
I can't get it to install because it keeps prompting me to download and install the driver. Can't ever get to pair the phone.
Binary100100 said:
I can't get it to install because it keeps prompting me to download and install the driver. Can't ever get to pair the phone.
Click to expand...
Click to collapse
same here. I contact Samsung send them the logs from SamsungFlowLogCollector and wait for a solution.
any luck for you ?
S8+ Microsoft Surface Pro 4 working great)
forisp2004 said:
same here. I contact Samsung send them the logs from SamsungFlowLogCollector and wait for a solution.
any luck for you ?
Click to expand...
Click to collapse
I'm sending them the logs now.
Binary100100 said:
I'm sending them the logs now.
Click to expand...
Click to collapse
Samsung send me back.
"According to the logs, "Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior" can not be loaded.
[Logs]
the type 'Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior, Microsoft.VisualStudio.Diagnostics.ServiceModelSink, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' 'Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior' cannot be loaded According to the logs, "Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior" can not be loaded.
(C:\Windows\Microsoft.NET\Framework\v4.0.30319\Config\machine.config line 238)
I think your PC environment has a problem."
I found the solution alone.
try only if your file has that 2 same wrong values ''<Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/>
''
check before modify.
you must modify machine.config from 2 places
1)C:\Windows\Microsoft.NET\Framework\v4.0.30319\Config\
2)C:\Windows\Microsoft.NET\Framework64\v4.0.30319\Config\
take ownership from file machine.config open it with wordpad go down near the end and find <commonBehaviors><endpointBehaviors><Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/></endpointBehaviors><serviceBehaviors><Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/></serviceBehaviors></commonBehaviors></system.serviceModel>
from that delete the 2
<Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/>
and you will have that <commonBehaviors><endpointBehaviors></endpointBehaviors><serviceBehaviors></serviceBehaviors></commonBehaviors></system.serviceModel>
save it and reboot your machine and voila that's it.
forisp2004 said:
Samsung send me back.
"According to the logs, "Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior" can not be loaded.
[Logs]
the type 'Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior, Microsoft.VisualStudio.Diagnostics.ServiceModelSink, Version=4.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' 'Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior' cannot be loaded According to the logs, "Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior" can not be loaded.
(C:\Windows\Microsoft.NET\Framework\v4.0.30319\Config\machine.config line 238)
I think your PC environment has a problem."
I found the solution alone.
try only if your file has that 2 same wrong values ''<Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/>
''
check before modify.
you must modify machine.config from 2 places
1)C:\Windows\Microsoft.NET\Framework\v4.0.30319\Config\
2)C:\Windows\Microsoft.NET\Framework64\v4.0.30319\Config\
take ownership from file machine.config open it with wordpad go down near the end and find <commonBehaviors><endpointBehaviors><Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/></endpointBehaviors><serviceBehaviors><Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/></serviceBehaviors></commonBehaviors></system.serviceModel>
from that delete the 2
<Microsoft.VisualStudio.Diagnostics.ServiceModelSink.Behavior/>
and you will have that <commonBehaviors><endpointBehaviors></endpointBehaviors><serviceBehaviors></serviceBehaviors></commonBehaviors></system.serviceModel>
save it and reboot your machine and voila that's it.
Click to expand...
Click to collapse
I'll make a backup of the two config files and give it a try when I get home. I just sent the logs to them today. How long did it take for them to respond to your inquiry?
Binary100100 said:
I'll make a backup of the two config files and give it a try when I get home. I just sent the logs to them today. How long did it take for them to respond to your inquiry?
Click to expand...
Click to collapse
1 day.
of course backup. number 1 rule.
but if you have not wrong values do not modify.
wrong value is ''<Microsoft.VisualStudio.Diagnostics.ServiceModel Sink.Behavior/>"
something else maybe not wrong value and your problem maybe something different .
if you try it let me know. :good:
forisp2004 said:
1 day.
of course backup. number 1 rule.
but if you have not wrong values do not modify.
wrong value is ''<Microsoft.VisualStudio.Diagnostics.ServiceModel Sink.Behavior/>"
something else maybe not wrong value and your problem maybe something different .
if you try it let me know. :good:
Click to expand...
Click to collapse
I just got home and checked and I don't have that line in either of my machine.config files.
My issue must be different than yours. I guess I'll just have to wait until I get my response back from them.
Binary100100 said:
I just got home and checked and I don't have that line in either of my machine.config files.
My issue must be different than yours. I guess I'll just have to wait until I get my response back from them.
Click to expand...
Click to collapse
sorry, you have to wait Samsung's response to clarify your issue.
I hope something easy and quick solution.
I have the same problem but mine says that TPM is locked or something I have read that its supported with fTPM and windows 10 update 1703 brings fTPM to all windows 10 computers but still it doesn't work I don't know why
forisp2004 said:
sorry, you have to wait Samsung's response to clarify your issue.
I hope something easy and quick solution.
Click to expand...
Click to collapse
I sent them the logs two days ago. Haven't heard back from them yet.
Just for the heck of it I tried it on two other computers. My Surface Pro 3 and another computer that I'm just using as a 24TB NAS drive.
None of them work. I'm thinking it's an issue with the app itself.

Categories

Resources