Related
Hi I'm new on here and a complete novice to flashing roms. I have a HTC Leo which I'm trying to switch to android but can't get Magdlr 112 onto my phone, I get through the first couple of pages it says it's uploading,I get the tri colour screen then grey htc screen but sticks at 0% then after a couple of minutes says error 260 and that it can't connect to the device. Any help would be great I'm wary of trying anything else because of the warnings of people on here about bricking it.
Ollyisagudun said:
Hi I'm new on here and a complete novice to flashing roms. I have a HTC Leo which I'm trying to switch to android but can't get Magdlr 112 onto my phone, I get through the first couple of pages it says it's uploading,I get the tri colour screen then grey htc screen but sticks at 0% then after a couple of minutes says error 260 and that it can't connect to the device. Any help would be great I'm wary of trying anything else because of the warnings of people on here about bricking it.
Click to expand...
Click to collapse
Do you already have HSPL flashed to your phone? It sounds like the bootloader is stock and is preventing you from flashing custom code to your phone. Are you running a custom or stock ROM at the moment?
Stock win 6.5. It's as it came from the provider which is Virgin.
Ollyisagudun said:
Stock win 6.5. It's as it came from the provider which is Virgin.
Click to expand...
Click to collapse
That's why. You need to have HSPL first. Please read this thread very carefully and follow the instructions to the "T".
Nearly there
Right I've put an old 1.48 version on my phone managed to get HSPL2 on to it, but am struggling with Magldr 1.13 can get it to load on but then the phone won't boot it sticks on the white screen with HTC but goes no further (no quietly brilliant) I can get the tri colour boot loader but it won't load Magldr I've tried a couple of versions but to no avail any help would be appreciated so close to getting Android on it, I'm about to start again from scratch. Cheers
What radio version do you have? You need 2.08.hspl AND the correct radio - 2.08.50.xx or higher x.xx.50 radio.
Radio version 2.05.51_2
boot loader shows SPL-2.08.HSPL 8G XE
0x05
0x50
Well there's your problem then
Heh guys you was faster.
Sent from my HTC HD2 using Tapatalk
When I try and flash a custom rom I'm getting an error message I've tried two different roms. Error happen
Read below for more information
Error Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
The phone is in flash mode and says Wait USB...USB
I can flash an official rom back onto the phone but not a custom rom?
Solution found active sync needed to have it's usb connection disabled.
Thanks for all your help I'm rocking Froyo and soon Gingerbread.
Yes radio will solve the problem of getting stuck on white HTC screen after installing magldr.
Boot to bootloader mode, connect to pc, when usb shows run the CustomRUU in the radi ofile you downloaded. Ensure it is a 50 not 51 series radio. You can try 2.15.50 (see link in my signature). If the download doesn't have a CustomRUU.exe file included then you can use one from any winmo custom rom.
Got the radio version cheers all good, best Gingerbread rom? Or should I stick with froyo? Version I have of gingerbread won't load can't find the usbError Description: USB init failed
Info: .\RSPL\RSPL.cpp (723)
?
Read the FAQ section here
As to the best rom that is a matter of personal preference. I don't like GB as I prefer Sense, but tastes vary.
Ever since I went to wp7 and back to android, my amazing hd2 has never been the same since. For weeks I have had freezing, so wanted to get a clean slate and start over. I did the following
Task29
Magldr 1.3
wanted to install nexushd2 so had to install
CWM_Recovery_for_NexusHD2_135M
it crashed towards the end of the install, ok I try to go back to magldr...but even tho I hold the button I dont get the options. I try it all again...same problem. I heard going back to stock 3.14 will fix most problems...it also hangs but at 8%?
Its now 6am and I need sleep...can anybody help...I really need a phone for tomorrow.
Thanks in advance
PS - Currently
PB81100 HX-BC
SPL-2.08.HSPL 8G EX
0X45
0X40
CotuallaHSPL
RUUNBH
Upgraed ROM code error, Please try again
Is that ok?
I got a quick question, did you reformat your SD card after you removed Windows Phone 7? If not this is probably your pro.lemons as WP7 cormates your card in a funky way so the phone tvinls the SD card is the enternal memory, I forget what it is called. But this is the same in WP7 native devices as they actually use SD card for memory and not enternal chips.
The best way to do this is to either vet an adapter and put your card in a digital camera and format it. Then reformat it again to Fat with your computer. Are you can just use your computer, but I suggest the digital camera as it will 100% remove the funky format.
Go into bootloader and flash a correct stock rom from USB. If it doesn't take confirm it's correct for your phone and try again.
sticking at 8% means a problem with installing the radio.
Put it in a plastic bag and pop it in the fridge for 30 minutes. remove and reflash.
I would recommend extracting the 3.14 installation file (using winrar).
Rename the RUU_signed.nbh to 'LEOIMG.nbh'.
Copy this file into the root of your SD Card, and pop the card in the phone.
Boot the phone whilst holding in the volume down button and let it flash.
If cooling the phone helped, send it back under warranty (you have got rid of HSPL, so all is good now.
I got mircosdhc to usb today, copied LEOIMG.NBH to sd, tried to flash but getting 28002 error not allowed
i then throws me back to spl 1.42
I have tried both 3.14 and 1.66 official roms...both sdflash and romupdateutility.
When I try sdflash with leoimg.nbg it gets to 1% then shuts down.
Is my hd2 dead? it doesnt even get orange led charge :-/
Tri colour screen now says
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
Is that ok, I dont remember if being that
update
cant flash radios either, shows the progress bar then restarts.
I tried :
2.15.50.14
Gutted, its my best phone ever
hmm, quite a rash of stuck radios this past week or so, , hardware coming to the end of its flashable life?
@OP, some people are recommending (myself included it seems, by passing it on) chilling the phone in a sealed bag in fridge freezer, no sim no sd, then when its cool, put sd in and try to flash real quick, try a few times, keeping it sealed and cool.
Aparently the theory is that the hardware is overheating, and the cooling lets it work well enough for a little while.
There are one or two what look like success stories, it has to be said, but i wouldn't put a bet on it myself just yet.
Good luck.
(oh and i wouldnt put the phone in the bag in a warm room either, , take it outside for a while first, let it be cool before it goes in teh bag, less chance of condensation.)
It doesnt look good...either get a black screen with a triangle!
or if I get into the tri colour bootloader it says:
upgrade rom code error please try again
everytime i try flash a radio it goes either 0% or 8% reboots phone.
I wish I stayed on sd...never had any problems ever...ever since win7 my phone hasnt been the same.
Any more advice or links would be great, keep em coming. I dont want to give up on my hd2 just yet...Im mean its still (imo) one of the best android phones about
@ samsamuel
I cant flash via sd...keeps giving me
upgrade rom code error please try again
should i change my spl or something? its currently:
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
do you know if that is ok?
this might be overstating an obvious that you've thought of, but are you sure you are using the correct stock ROM for your region? Have you tried flashing a custom ROM just to see what happens?
fracmo2000 said:
@ samsamuel
I cant flash via sd...keeps giving me
upgrade rom code error please try again
should i change my spl or something? its currently:
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
do you know if that is ok?
Click to expand...
Click to collapse
flash back to hspl 3 and try again,if no succes ur bootloader is damaged and that will be problem
fracmo2000 said:
@ samsamuel
I cant flash via sd...keeps giving me
upgrade rom code error please try again
should i change my spl or something? its currently:
hx-bc
spl 1.42.0000 xe
micro (led) 0x05
microP(TOUCH) 0X40
do you know if that is ok?
Click to expand...
Click to collapse
that would be a stock spl then,, and with the rom update error, that means you have flashed the wrong stock rom from sd card. It has removed hspl, then the flash failed because you had (have) stock 1.42.0000 spl.
enter bootloader - usb - hspl4 - 2.08.hspl HSPL not 0000 - into bootloader again, has the spl changed? if not, then flashing is stuck, and you are in the stuck radio situation, if it HAS changed, now try flashing a rom or radio, , , flash from usb, see what happens.
orangekid said:
this might be overstating an obvious that you've thought of, but are you sure you are using the correct stock ROM for your region? Have you tried flashing a custom ROM just to see what happens?
Click to expand...
Click to collapse
not at all, keep me coming...I honestly dont see any other phone just now that I want (in the uk at least)...maybe the artrix but thats not for a few months...so need to get this baby back working!
I tried both 1.66 and 3.14 wwe (i couldnt see a uk one...
_HTC HD2_RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.07U_2.06.51.07_Ship
RUU_Leo_S_HTC_WWE_3.14.405.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
Are they ok?
You could go to HTC's website, and search for HD2, and then go to downloads, and try downloading the newest rom that the site offers. You need to enter your serial number which is located under the battery. With some luck you will end up having a shipped rom, which has the same cid as your phone, and you will then be able to flash your phone via usb cable (from the tricolor screen).
If for some reason the HTC website won't accept your srial number, try to select another country from the top right part of the website.
I live in Serbia, and the Serbian HTC page has no rom downloads for HD2, the International page won't accept my serial, but the polish page did accept it. So keep trying, until the webpage accepts your sn.
If you are in no luck, you could try downloading roms from http://www.shipped-roms.com/.
Hope you will succeed in your quest to resurrect your phone.
Best of luck
d3m0n
d3m0n1 said:
You could go to HTC's website, and search for HD2, and then go to downloads, and try downloading the newest rom that the site offers. You need to enter your serial number which is located under the battery. With some luck you will end up having a shipped rom, which has the same cid as your phone, and you will then be able to flash your phone via usb cable (from the tricolor screen).
If for some reason the HTC website won't accept your srial number, try to select another country from the top right part of the website.
I live in Serbia, and the Serbian HTC page has no rom downloads for HD2, the International page won't accept my serial, but the polish page did accept it. So keep trying, until the webpage accepts your sn.
If you are in no luck, you could try downloading roms from http://www.shipped-roms.com/.
Hope you will succeed in your quest to resurrect your phone.
Best of luck
d3m0n
Click to expand...
Click to collapse
Ha, funny you should say mention that about HTCs site...but my S/N didnt work either. I wasnt sure if it was something to do with me/my phone or just the site was rubbish!
Im currently downloading an o2 rom frmo shippedroms (great site, thanks) so all my fingers and toes are crossed.
Funny thing is, I can flash hspl and hspl2, I managed to flash radio but not rom...keeps rebooting.
Did u take out sim and SD and try flashing?
@samsamuel
Well, I managed to get hspl4 on ok (2.08hspl) and then flashed a win6.5 rom it worked...but doesnt boot (stuck at flash screen)
When I downloaded official roms from both htc and shippedroms...they are corrupt. I used winrar, 7zip and tried to just run the packaged exe file...doesnt open.
Can anybody help me test these files and see if its me or have a good office rom they can upload?
@milli
when i managed to get an win6.5 rom flashed, sd was in, sim was out (i used hspl usb flash method)
EDIT - Found some o2 shipped roms on xda...extracted and going to try usb flash via hspl4
well i can flash radios and roms via hspl4 usb flash method AND usb via pc...but still cannot boot. Stuck at inital splash screen.
Any ideas now? We have made progress
edit - i have tried both custom roms and shipped o2 (uk) roms
Did you try hard reset after you'd flashed the rom(s)??
tried it once or twice, but not everytime. redownloading another rom
RUU_Le2_UK_1.43.206.4_Radio_Signed_15.26.50.07U_2.04.50.22_2_Ship_WORKING.exe (191,374 KB)
i hope this works...im getting desperate. Im still unsure at whats went wrong. Is it something wrong with my nand memory?
I can now flash radio, roms but yet cannot boot (Stuck at white htc splash...the red text sometimes appears...sometimes it doesnt).
edit - that rom failed to flash
Hi folks,
I have a T-Mobile branded HD2 that gets stuck on bootscreen. Since this one is owned by the company I work for I should not flash custom ROMs or whatever. I got it from a colleague with this error.
What I did is downloading the latest official ROM from HTC with T-Mobile branding, extracted the .nbh file and stored it as LEOIMG.nbh on its SD card. I flashed the ROM, removed battery, put it back in and immediately did a hard reset. Still no luck it keeps stuck in the boot screen showing the ugly circle. No animation, no nothing.
Any ideas?
Regards,
Chris
What is the full name of the official ROM you got .and did I understand you correst you got it from the T-Mobile website? Also what does it say when you put it in BOOt loader?
Filename:
_HTC HD2_RUU_Leo_TMO_DE_1.72.111.4_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship.exe
Download from:
http://www.htc.com/de/supportdownloadlist.aspx?p_id=297&act=sd&cat=2
I am not sure what you mean with bootloader? VolDwn+Power?
PB1100 HX-BC
SPL-1.66.000 XE
MicroP(LED) 0x05
MicroP(Touch) 0x50
Let me know in case you need more details.
It gets even more weird...
I put the phone on charge (switched off). It suddenly switched itself on and then booted into windows. It came to the point where it asks for the PIN. I entered it and as soon as it accepted the code it rebooted again and is stuck on the same screen as ever.
Sorry I was changing my ROM, That is why it took a minute, Are you sure you have a T-Mobile HD2? Cause it says in the name of the ROM you posted that it has a 2.07.51.22 and that radio is deadly to a T-Mobile HD2.
Does it have a green send button and a red end button?
Also did you enter the serial number of your HD2 in the HTC site to verify that this ROM is for your HD2?
What you said about it rebooting when you plugged the charger in is weird.
I bought this HTC (and several others) all from T-Mobile, since we got some company agreement. When I first got it disfunctional it booted up with this circular bootscreen in T-Mobile colors. I personaly own a Desire HD, so I know about the uncustomized bootscreen.
This is T-Mobile for Germany, not UK or US. For the US version the radio won´t work since bands are different. I have heard about that...
This device does not have colored buttons.
Yes, I have entered the serial number on this site and it has been validated. Then I downloaded and unpacked it just the way it is described in this forum.
I also tried to download the original, latest, unbranded HTC ROM, but it did not validate my SN.
I have reformatted the original 2GB SD card with FAT32 and tried the same. After it says UPDATE SUCCESS it does nothing. Is this correct?
I took off the battery and after a couple of seconds back in, doing a hard reset. It then still got stuck on the bootscreen.
Ok do this download the Task 29 by ShaDrak from post #1 of the Task 29 thread here on XDA and run a Task 29 on the HD2 then download HSPL 4 (link in my sig) and flash HSPL 3.03. then try to flash your ROM again. If it flashes successfully then use the HSPL utility to reset y our correct SPL. I will have to go see if I can find the correct SPL for you if you don't know whioch one it is.
Thanks for your help, but I think I´ll rather return it for a new one then. This HD2 is for testing our mobile website, so one developer will need to wait a little longer for a replacement. This smartphone is 3 weeks old (half a week of use due to vacation), so I do not want to brick it and stick with it. Last time I did HSPL was with my old diamond, feels like a decade ago.
I am limited with downloads at my company due to firewall restrictions and I am not allowed to install programs. I am glad that I got USB allowed, though I am part of the admin crew
I´d even take it home, but I do not have windows running on any of my computers.
Ferrosti said:
I am not sure what you mean with bootloader? VolDwn+Power?
Click to expand...
Click to collapse
This is what I mean by bootloader, once you see the multicolor bootloader screen connect it to your computer via USB and wait for the Serial to change to USB and Right click the RUU for the ROM and run as administrator.
I understand you not wanting to brick it and your issue with downloads, that does suck. But the task 29 just does a wipe of the ROM partition of the NAND memory and reformats that partition. Task 29 is a very small download also, very very small, the same with HSPL 4. I suggested HSPL for as it will disable the CID check on the flash and allow you to flash a ROm that is not for that particular HD2. And all you have to do to revert back is run the HSPL again but pick the SPL not the HSPL you want, it ask you what version of HSPL or SPL you want to flash. Also you have a International HD2 and they are not as prone to bricking as the TMOUS because they can be flashed with any radio version for the HD2.
It comes to my mind that I have a damn old windows installation on my computer. Maybe I´ll give it a try at home over the weekend.
The phone does not even switch from serial to USB mode as you described. Could it be because there is no active sync installed? I tried it with my personal Desire HD and I got access to its SD card.
How do I find out which SPL to flash to have it back to its original state? Is it the 1.66.000 that was shown in bootloader? Where do I get it?
Go into the Bootloader and it should say the SPL version
Mines for example is
SPL-2.08.HSPL 8G XE
CotullaHSPL
If yours should say SPL-(version number) without the HSPL/Cotulla since it shouldnt have HSPL
If Windows has the drivers for the HD2 installed (Active Sync/Center installed) it will say USB as long as the plugs and the wire are good if it stays stuck on Serial that just means either the HD2 isn't detecting windows or Windows isn't detecting it
Ferrosti said:
It comes to my mind that I have a damn old windows installation on my computer. Maybe I´ll give it a try at home over the weekend.
The phone does not even switch from serial to USB mode as you described. Could it be because there is no active sync installed? I tried it with my personal Desire HD and I got access to its SD card.
How do I find out which SPL to flash to have it back to its original state? Is it the 1.66.000 that was shown in bootloader? Where do I get it?
Click to expand...
Click to collapse
Yes I think the SPL 1.66 is the SPL for the 1.72.111.4 ROM you are trying to flash. The phone is technically suppose to install the drivers when you connect it to a computer in bootloader, but I have had to download and install the ActiveSync and the Windows Mobile Device Center too to get a computer to recognize my HD2 in bootloader (two separate computers) so yes installing the latest ActiveSync on your computer can help as it has device USB drivers with it.
Dont install ANYTHING.
If the phone is only 3 weeks old, send the damned thing back for a replacement.
Had the same problem with a european t-Mobile HD2. Sometimes (rarely) let me boot into windows, but mostly didnt.
Sent it back to HTC and they fixed and returned it within a week. Actually they said on their site that they were fixing it, but I ended up with a new phone......
So... either return it to your supplier for replacement, or send it off to HTC
Andy
I don´t know how, but I got it running on the day we have been discussing.
If I only knew how it worked I´d let you know.
After all this I put it on the charger and retried a last time before I would have taken it home (read above). I flashed the new T-Mobile branded ROM and it just worked.
Thanks for your help!
Hi every one please help me my phone stuck on bootloader screen i tried to flash it with an official ROM by using the sd card method or either the usb connection method but in booth cases it fails (error appears "NOT ALLOWED") when it gets to bootloader screen it shows that spl version is 3.03 i read in a thread that the gold card method will help me but i tried it with a help of a website to generate and send a goldcard by email but it doesn't works may be some thing wrong with gold card from the website so please gentlemen any one have an idea to solve this problem i am really afraid that i lost my phone please please please help !!!!!!!!!!!!!!!!!!!!!!!!!!!!
calm down there champ, you're just using the ROM for the wrong region.
go to the HTC support site and find your correct ROM for your region with your IMEI number and flash it, you don't need a gold card.
orangekid said:
calm down there champ, you're just using the ROM for the wrong region.
go to the HTC support site and find your correct ROM for your region with your IMEI number and flash it, you don't need a gold card.
Click to expand...
Click to collapse
thanks for reply I hop you are right but how can I find the correct ROM by my IMEI I saw just the serial number and when I enter my serial number they told me that the ROM is not suitable with my device
Bareq said:
Hi every one please help me my phone stuck on bootloader screen i tried to flash it with an official ROM by using the sd card method or either the usb connection method but in booth cases it fails (error appears "NOT ALLOWED") when it gets to bootloader screen it shows that spl version is 3.03 i read in a thread that the gold card method will help me but i tried it with a help of a website to generate and send a goldcard by email but it doesn't works may be some thing wrong with gold card from the website so please gentlemen any one have an idea to solve this problem i am really afraid that i lost my phone please please please help !!!!!!!!!!!!!!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
Calm down mate
The possible reason is the rom you tried to flash is not the. CORRECT STOCK ROM.
Go to HTC website to download unbranded hd2 rom or go to your carrier website for a branded hd2.
Else, you should check your micro sd condition
Cheers
Hello, i have HD2 from Europe unbranded and alredy instaled HardSPL cottula.
but i mistake and flash with HD2 T-Mobile US rom - RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship and stuck on 9% with red line.
now i flash other eu rom RUU_Leo_HTC_WWE_1.43.405.1_Radio_Signed_15.26.50.07U_2.04.50_22_2_Ship but always stuck on 9% also tried with other rom same :/
can any body help me, this is software err not hardware right?
p.s. information of bl is
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
Phone was bring to life, after flashing with RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
but now only on white screen with HTC logo stay :/ where is the problem?
Hi everyone!
I am very sorry for such a n00b-post, but I really cannot find a solution.
The problem:
I recently got a HD2 of a friends who did not use it anymore, because Android suddently stopped working. Now it's stuck at a black screen [A] saying:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
I tried resetting the phone using the red button near the battery, but it did not solve the problem. I am able to boot the HD2 into recovery-mode (colory screen) but then, after connecting to a pc it does not change from "serial" to "usb".
I have installed WMDC on my W7 64-bit system. I have also tried to use "RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship" (from the 4shared "shipped LEO roms"), but none of them recognises my HD2 neither in Recovery nor in the black screen [A].
Is this phone useless? What can I try to revive it?
What might be helpfull: when normally booting, the phone vibrates once during the HTC-screen and 5 times after the black screen [A] appears.
andrejazzz said:
The problem:
Android suddently stopped working. Now it's stuck at a black screen [A] saying:
aMAGLDR V1.13
Build: Feb 1 2011 03:46:07
by Cotulla 2011
I am able to boot the HD2 into recovery-mode (colory screen) but then, after connecting to a pc it does not change from "serial" to "usb".
I have installed WMDC on my W7 64-bit system. I have also tried to use "RUU_Leo_HTC_NLD_1.66.404.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship" (from the 4shared "shipped LEO roms"), but none of them recognises my HD2 neither in Recovery nor in the black screen [A].
What might be helpfull: when normally booting, the phone vibrates once during the HTC-screen and 5 times after the black screen [A] appears.
Click to expand...
Click to collapse
Since you're unable to connect to PC, then you can't re-flash HSPL.
HSPL needed to force flash any shipped WM6.5 ROMs to HD2.
Then the only way is to flash original WM6.5 ROM for your device from uSD.
If you're not sure what CID, just download any HD2 shipped ROMs and try to flash from uSD.
Just be careful not to flash EU's ROM on T-Mobile device!
Extract the ".exe" file, then rename the ".nbh" file into "leo.nbh", copy that to root of uSD.
Power up your device while pressing vol down button.
Don't worry if the ROM refuse to flash, it's just a wrong CID.
But to make sure, connect your device to another clean PC (without android drivers inside, just WMDC), preferably a PC sets for syncing WP7/WP8 devices.
And make sure your device turns on by itself when charger is connected (auto turn on from off state).
That's just to make sure that usb connector is not damaged.
HD2 vibrate 1x at power on, it's normal.
Vibrate 5x after magldr shows up, I suspect something wrong with magldr or the ROM itself (corrupted or something).
Another possibility is some NAND bad blocks.
But if it's vibrate 5x at power on, then you have a bad luck.
The point is, flash the original ROM first.
If it's success, then flash HSPL.
After that, the rest is up to you..
Firstly, I want to thank you very much for your quick and extensive answer!
But I have only one tiny question: are these the ROMS which I can find at http: //www . 4shared . com/dir/22189940/b8552fa0/Shipped_Leo_ROMs.html#dir=MGRa1Cen ? And you mean I should just pick one and try?
You can also find HD2 shipped ROMs here.
Anything that has "TMO" are T-mobile ROMs, otherwise it's EU.
Again, don't flash EU's ROM on TMO devices!
The first 3 digit are the ROM version (1.66, 1.48. etc.), 3.14 is the latest WM6.5 ROM.
The next 3 digit are CID code (207, 404, 707, etc.).
Like I've said, if you don't know which CID for your HD2, then just download all ROMs from different CID then flash it one-by-one using uSD.
Thanks!
So far I have tried the 404 and 162 (edit: and 161, 911), but so far without luck. I'll keep you posted!
Tiny question: is it normal that I cannot shutdown in Recovery Mode?
Perhaps some useful info shown in Recovery:
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x40
Correct me if I'm wrong, but it looks like an EU HD2, TMO HD2 are rarely using hynix nand, made around late 2009 or early 2010.
Just try to flash ROM with CID for your friend's country first.
If failed, then try another CID.
There should be one or two info about CID number vs. country somewhere around.
Good luck!
Sent from my Windead Phone 7 using xda app-developers app
At this moment I have tried all the NLD roms with no result. Also I have tried roms from several european countries, but none of them works:/ Might it help if I give the serial number?
And what might be worth saying: my phone turns on when connected to AC power / wall-charger; when connected to charger the "serial" disappears...
Thanks for all your help!!!
Have you try connect to other PC?
When flasing ROM from uSD and failed, what error message you got?
If it's "CID mismatch" or something like that, than it's definitely a wrong CID.
If it's "ROM update error bla bla bla", it's most likely corrupted flash image or the uSD itself (use a small sized uSD, 1gb would be fine).
Even if you flash the correct CID, without removing HSPL first, it would still throw an error message "ROM update error bla bla bla" during flashing Radio.
Then it will restart and retry to flash again on it's own.
By the way, I don't know if there are ways to flash HSPL from uSD.
Or guide on how to make a "gold card".
I sugest you search it.
Worth to try if you couldn't find the correct CID for your device.
CID from serial number?
Yes, back in 2010/11 HTC site provides s/n checking for download the correct ROM.
But now it's gone.
Sent from my Windead Phone 7 using xda app-developers app
Thank you very, very much for helping such a newbie ^^
At this moment, I am able to get into the update-menu: I changed the filename to LEOIMG.nbh. The only problem is that all the Dutch images give the same error: 00018003 : Radio (V2) - FAIL.
What could I do to solve this error? Use the freezer-trick or wouldn't it make any sense?
edit: it does boot when I connect to another W7 pc with WMDC (replies " Not connected" ), only it automatically starts the update-procedure (which fails).
There are no such thing as newbie, that's why we need to learn.
Error 00018003 during Radio flash?
I have no idea what error is that.
But first, are you sure that your friend bought the phone on local shop?
I mean, not imported, or when he/she travel overseas, or has the mainboard swapped at HTC service center.
It happens to me when my second HD2 suddenly has no signal, about 2 years ago.
Brought it to local service center and they swapped the mainboard without telling me.
And the swapped mainboard has CID from 404 (europe), the original was 707 (indonesia).
Okay, back to error something.
WMDC won't recognize the phone unless it's a working WM6.5 device, or a working WP7 device with WP7 SDK + Zune installed on your PC.
Just put the phone into bootloader screen (3 color screen), then connect it to a clean PC.
Does the "Serial" changed to "USB"..?
If it does, reflash HSPL 2.08 using HSPL4 package.
Then flash Radio ROM only, 2.15.50.14 is a good one.
Again, an EU HD2 can use either EU's Radio ROM or T-Mobile's Radio ROM.
But a T-Mobile HD2 can only use a T-Mobile's ROM..!
If the "Serial" doesn't change to "USB" but on your PC makes sound like something is plugged in, open device manager and look for an unknown device (no drivers loaded).
Expand it, what does it says?
To be honest: I am not 100% sure that it is an European (Dutch) phone. What I saw when I opened the phone's back was that the warranty-seals on the screws were molested. I don't think he got the motherboard replaced: way to expensive in relation to a new phone...
The bootloader screen gives now the following text:
RUUNBH
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0X05
CotullaHSPL 0x40
Upgrade ROM error
Please try again
When I connected it to a clean pc, the phone booted and gave another upgrade-error, only this time on a black screen (I got the uSD out the phone).
After booting the phone and connecting to a pc the "serial" does not change to "usb"...
When I tried to install WMDC I get the error "Installationpackage not supported by processor". Seems like bullcrap, but there it ends. No yellow exclamation marks in Device Manager...
I have yet not tried to flash a T-Mobile ROM to the phone. I have tried all the NLD ROM's: 1.66.404 ; 1.48.404 ; 1.66.404 ; 3.14.404 ; 1.66.404 ; 1.43.404
I have yet not tried the other ROMs I downloaded, but I will tomorrow. To start 161 does not work.
Also: I cannot shutdown when in bootloader or MAGDLr, is that correct?
What colour are your call & end key buttons !
if white you have standard EU type model. T-Mobile EU models are same as any EU model & can flash any ROM/Radio
If green & red you have a T-Mobile USA model (TMOUS) & need correct ROM (found in HD2 Wiki)
T-Mobile USA model needs care as if flash wrong radio version you can brick it.
Flashing via SD card should be last choice as first stage of a SD card flash is install of the SPL to standard SPL from the nbh which means you have no CID bypass as HSPL gone.
ideally you need a Windows 7 32bit machine with a known working WMDC setup & try flashing a suitable rom once decided on EU or TMOUS device.
As you have HSPL on your HD2 already it will bypass CID if flash via PC so you can flash any CID code rom.
Try connecting device to PC (with known good WMDC) and use reset button on HD2 to boot to bootloader & see if get any luck in running ROM installer from PC.
If lucky the USB flash issue is PC & drivers rather than hardware on HD2.
I would suspect you have nand issues on HD2 or perhaps worse, if nand sometimes you can get it back if persistent & get something to flash completely.
Thanks MisterB for adds up.
So am I, suspected a nand issue.
The reason I want him to revert back to original SPL & Radio is to make sure that it's a nand related problems, not radio hardware problems.
If he managed to find the correct CID for his phone, he could easily reverts back in case somethings wrong in the future after playing with custom ROMs.
This also happens to my friend's phone a couple months ago.
But in her case, the bad blocks are definitely located where magldr resides, and many more on data partition.
She can flash shipped ROMs completely, but it refuses to boot.
Can't flash a WP7 ROM because magldr freezes when it's loading, can't even bring the menu screen.
She can run a native sd android build for a couple weeks, but then it acting strange again.
Then finally she just gave up and bought another phone.
@andrejazzz:
You can't shutdown on bootloader (3 color) screen.
Remove the battery is the only way to shutdown, or press the reset button to restart.
But you can shutdown/restart or anything else on magldr menu screen.
Press & hold power key right when magldr loads up (before it's start to "go go go").
In addition, you can download WMDC x86 version here, and x64 version here..
He may indeed need try SD flash but I would exhaust all options of USB cable flash via PC first as retaining HSPL will be useful to start with as any generic HTC ROM could be used for the USB cable flash.
If that is not possible then flashing via SD is only viable option & indeed many times only way get over bad boot/nand issues but with all the CID versions for HTC regions & operator branded regions you have a hard job knowing the right one, you could even try the right ROM & as it does not flash overlook it for further testing.
I see he has tried SD flashing but still has HSPL so either SD card is not best suited for nbh flashing or nand/hardware that bad even first stage of flash is not possible.
If I was testing this device & trying recovery I would probably try freezer test to cool device prior flashing & make good effort on USB flash before going on to SD card.
Most well used Android HD2s these days have nand or bga issues to some degree as android works the hardware so much harder than WM6.5.
You really need be sure PC & driver are known good for flashing & if going to SD flashing that SD card is suitable or you will waste a lot of time & effort.
Loads of links & tips for all the software & some threads are in the HD2 Wiki
I apologize for replying so late, but I have had no time: I had a few tests at school
@Mister B: I have a black HD2 with white icons, so I have a european model.
I have installed installed the X86 on a clean 32-bit system, but it does not recognize the phone. I have reinstalled the WMDC on my W7 64-bit system, but still it does not recognize the hd2. I have no other Windows Phones, so I am not able to verify the WMDC-installations.
When I connect to a pc, the phone boots and shows: "Software update failed! Please try again"
@Shadow_Nexus: Correct, that is exactly what happens. I do not completely understand what you mean with "Press & hold power key right when magldr loads up (before it's start to "go go go")", could you please explain?
@Mister B: How could I check if the SD-card might be the problem? It is a 16GB Class 4 Kingston SD. I have tried all the NLD-roms and other versions (random countries, not TMOUS). I have tried the freezer trick with a NLD-rom on a mSD, but it did not work.
Thanks for all your help!
Best using a 2gb or 4gb (8gb max) card for nbh flashing & do a proper fat32 format with something like hp format tool before using it.
link below may help:
http://forum.xda-developers.com/showthread.php?t=681317
Again, thank you very much for your reply. But: do you have any clue what ROM's I should try? I am asking this, because I have already tried all the NLD ROM's I found on the site @Shadow_Nexus gave in post #4, but every one of them returns the same error. Should I switch to another country and try, for example, all German ROM's?
I got my hands on another HD2 and when I connect that one to my pc it show up, named "HTC Sync". The bricked one still does not respond:/ Should I retry all the non-TMO roms I can find?
Edit: My brother "helped" me out and sold the phone...