Phone won't boot :( - Galaxy 3 General

My galaxy 3 (apollo) came with 2.1, so I thought I would update to 2.2. I downloaded JPU from hotfile, the one that uses sampro.pl as password. Had odin set up with .ops, one package, nothing else checked. It flashes it and restarts a few times, then gets to the samsung logo which flashes, then it just freezes.
I have tried wiping the cache and factory reset. I tried JPS too (which I knew worked on my other phone - but that I upgraded from 2.2 to 2.2) but nothing seems to work.
Have I done something wrong?

I would suggest to flash your mobile once again
by following the instructions in the below link.
http://forum.xda-developewjrs.com/showthread.php?t=1372414
I hope it helps.

Somehow I got it working, I flashed Cyanogenmod and it worked, then wiped all including dalvik cache with cwm, still didn't work when I flashed froyo. So I removed sbl.bin and boot.bin from the .tar, tried and still nothing, then wiped data and cache one last time and on reboot it started up!
I had wiped the data and cache tens of times before and after flashing before, so it was either removing the bootloader or wiping the dalvik cache that made a difference. Only took all day to update my phone!

Try to get some different source for froyo....

I'm Glad you got it working again! next time you need stock firmware, use the one available in this forum by searching "stock jpu" the dev has removed the bootloaders and therefore it is much safer, and yeh as you've discovered, when it doubt, wipe the dalvik!

Hi
Yeah I did come across a thread where someone had removed the bootloaders, but all the files were either removed because they were on megaupload, or linked to JPI. I could have used that, infact I did connect it to kies at the start of the day and it said it could upgrade me to JPU. I wanted to do it by odin though! Then 12 hours later and trying countless other firmwares it worked. I just opened the .tar with 7zip and deleted boot.bin and sbl.bin, I had no idea if that would work or not!
It wasn't stuck in a boot loop so the bootloader couldn't have been corrupt? Perhaps it was the dalvik cache needed to be wiped from 2.1 to 2.2? I couldn't see anyway to wipe it with the stock samsung recovery.
Is CWM available for this phone? (without having to flash Cyanogen!)

mike_1983 said:
Hi
Yeah I did come across a thread where someone had removed the bootloaders, but all the files were either removed because they were on megaupload, or linked to JPI. I could have used that, infact I did connect it to kies at the start of the day and it said it could upgrade me to JPU. I wanted to do it by odin though! Then 12 hours later and trying countless other firmwares it worked. I just opened the .tar with 7zip and deleted boot.bin and sbl.bin, I had no idea if that would work or not!
It wasn't stuck in a boot loop so the bootloader couldn't have been corrupt? Perhaps it was the dalvik cache needed to be wiped from 2.1 to 2.2? I couldn't see anyway to wipe it with the stock samsung recovery.
Is CWM available for this phone? (without having to flash Cyanogen!)
Click to expand...
Click to collapse
CM7 is a aftermarket firmware, so it wont be available in the updates....and also, samsung wont give us this kind of good looking ROM anyways, flashing a ROM is a whole lot faster than updating through Kies or others...

J.Purungrit said:
CM7 is a aftermarket firmware, so it wont be available in the updates....and also, samsung wont give us this kind of good looking ROM anyways, flashing a ROM is a whole lot faster than updating through Kies or others...
Click to expand...
Click to collapse
Hi
I just meant is ClockworkMod available for the Galaxy 3. I noticed it was on my phone when I flashed Cyanogen Mod.
I have a Galaxy 5, the CM7 for that seems more complete, I noticed the camera doesn't work on the Galaxy 3 CM7. I thought they would both be about the same functionality.
In my case flashing a rom was slower as it gave me a bunch of problems, but yeah flashing is usually faster

mike_1983 said:
Hi
I just meant is ClockworkMod available for the Galaxy 3. I noticed it was on my phone when I flashed Cyanogen Mod.
I have a Galaxy 5, the CM7 for that seems more complete, I noticed the camera doesn't work on the Galaxy 3 CM7. I thought they would both be about the same functionality.
In my case flashing a rom was slower as it gave me a bunch of problems, but yeah flashing is usually faster
Click to expand...
Click to collapse
Camera has been mostly fixed in CM7 and Galaxy 5 has been out for longer so devs have had more time. Anyway, all custom ROM's come with CWM Recovery.

I think you can install cwm for stock Roms..I have seen similar question in some thread posted here..which says your phone should be initially rooted to do this..
I am not sure abt the process..but as far as I know..you have to follow these steps :
download an app called as z4root..search in Google..its not available in market..
root your phone..it will ask two options to either root permanently or temporarily..go permanently..(you can unroot it I think so don't worry)
and finally you can try several custom kernals.. head over to development thread for that.I prefer fugumod kernal..take the tar file and flash it via Odin (safer side wipe dalvik as well as cache and reboot)
since its a stock rom ..you will not be having dedicated option to go for recovery, use volume keys,power button and the center button together..
bit of headache..
try at your own risk..or if I am wrong, please advice

Smonic said:
Camera has been mostly fixed in CM7 and Galaxy 5 has been out for longer so devs have had more time. Anyway, all custom ROM's come with CWM Recovery.
Click to expand...
Click to collapse
Ah I didnt know the Galaxy 5 had been out longer. The camera didn't work when I used the latest CM7 for the Galaxy 3, when it took a picture it looked like a commodore loading screen But I didn't check gallery thinking about it, perhaps they came out alright

prabhuthelegend said:
I think you can install cwm for stock Roms..I have seen similar question in some thread posted here..which says your phone should be initially rooted to do this..
I am not sure abt the process..but as far as I know..you have to follow these steps :
download an app called as z4root..search in Google..its not available in market..
root your phone..it will ask two options to either root permanently or temporarily..go permanently..(you can unroot it I think so don't worry)
and finally you can try several custom kernals.. head over to development thread for that.I prefer fugumod kernal..take the tar file and flash it via Odin (safer side wipe dalvik as well as cache and reboot)
since its a stock rom ..you will not be having dedicated option to go for recovery, use volume keys,power button and the center button together..
bit of headache..
try at your own risk..or if I am wrong, please advice
Click to expand...
Click to collapse
I rooted the phone with SuperOneClick, I think it worked! Anyway I gave the phone to my brother now and hes just interested in a working phone, not messing about with roms! I may get the phone again when it comes down in price again (you can get them refurbished in brand new condition here in UK)
Thanks!

Related

[GUIDE] Sprint sph p100 stock firmware RECEOVERY: last resort.

Ok i decided i post what i did to recovery my sprints tab from a bad kernel flash that i didn't install clock work recovery, I thought my tab was a lost cause which i even chatted with hsn were i bought mine at for a replacement which would've took up to 30days.. So awhile i wait for that i decided to try and get it working till i get the prepaid label lol
Matter what i did it kept getting stuck at the samsung screen and couldn't get into recovery but download mode work luckly. i tried all kernels listed and it still got stuck which at the time i thought my tab was bricked or semi brick.
What i did is keep searching for the stock firmware which was hard to find but i found this thread http://forum.xda-developers.com/showthread.php?p=9753941#post9753941
Heres a direct link http://www.multiupload.com/WDKOUJSM2G
Thanks to ZoinksS2k for the tab sprint no modem firmware
And downloaded the stock no modem firmware the modem one is listed too but it will kill your gps and 3g might not work so i just did the no modem one.
So i downloaded it and odin was package with it and i couldn't get it to detect my tab in download mode ony when the tab was off it detected it..
So i tried heimdall and at first i couldn't get it to flash the start button was grayed out because i was putting the tar file into pda/code so i open the tar file and found factory.rfs param.ifs and cache.rfs and dbdata.rfs so i loaded all thoes in the heimfall boxes and than loaded the stock zimage which is in the tar too.
And than i flashed and saw the samsung screen and it went right pass it and played the samsung splash screen so i knew i was getting somewhere so it got stuck on the next samsung screen again.. So i turn it off and hold home button and volume up button than i push the power button and hold all 3 buttons till i saw the samsung screen and i left go the power button and the stock recovery loaded right up
So i did the wipe data/factory reset and i also did the wipe cache data just in case but im sure just the factory reset would work, And i restarted the tab and it went pass all screens and it loaded android!!! And everything was working 3g wifi gps and everything else.
So hopefully this guide will help others as a last resort if you ony get the samsung screen and download mode ony,If you get the receovery than just do the factory wipe.
This is worth a try first than sending it back to samsung and having to wait too get your tab back It sure saved me from having to send it back too hsn or samsung.
If you want you can thank me if this help you for providing the info
Gordesky,
Any idea how to go back to stock firmware + stock modem and all that from using the voodoo kernel? I have CWM Recovery 3.0 working.
Because, after going into Voodoo CWM Recovery, using wipe data/factory reset still keeps the kernel that I installed on - which is what makes my camera screwy.
If you want to go back to fully stock then follow his instructions and flash the stock kernel from the Zephyr thread. I actually am in the same boat as the OP and followed his instructions and now I'm fully back to stock.
Yep just do what I said which the tar file also have the stock kernel too.
Right now im on the voodoo kernel which works perfect except that cdrom problem but camera works for me so im gonna still with.this kernel so far. It seems the new sprint update doesint work right with the voodoo kernel problaby why I dont have any problems because I didint install the sprint update.
So when you go back too stock and want too give the voodoo another try dont install the sprint update when it asks you too, And everything should work other than the sdcard cdrom problems, Which I can deal with till it gets fixed because I do love the speed of this voodoo kernel
And the sound
Thank you gordesky1 for posting your experience because I was going through the exact same thing and I was at a loss as to how to resolve it. Unfortunately I did install the update but I'm pretty sure if I flash the same files again that I will go back to the original rom if that's necessary. The big problem with that is that the exchange fix in the update was something i was waiting for =\ so I think i'm going to wait and see if some of these issues are fixed in the next update but I wonder if we have to get Boushh a Sprint tab though =\ every day I curse myself for not getting a t-mobile or at least a Verizon tab *sigh*
No problem
Ya tell me about it... Bad thing for me is the sprint was my ony option which i got it because hsn were i bought it from had a flex pay on this tab which they ony have the sprint tab, and at the time i couldint pay 400 or 600$ right out. And i also got a 3years warranty on top of it from them even if i break it or drop it anywere which i pretty much got for free because they made a mistake at first with some software
The other tabs have cheaper 3g too like 5gb for 15 too 30$ a month.. But so far sprint is treating me good and the 3g has been stable so far and pretty fast loading webpages and can usely watch a youtube video but dont want too use up my monthy usage lol i usely use up too 500 too 600mbs max out of 2g and i useit every day and even download apps with it when im not near a wifi spot and listen too pandora too so i was suprized i didint get close too the 2gb limit yet.
Hopefully this thread will help more and save them from having too send it back too samsung or were they got it from, i know how it feels not having this tab which i use everyday at work.
I knew not to flash the modem from the restore package posted but when I tried to restore I used the .pit and the .tar. Failed at modem. So, being dumb I flashed the modem file. ugh.
Now I know all you need to do is flash the .tar, nothing else, no pit.
Your Post Saved Me!!!!!
10 characters
Your welcome and glad it helped I figure it was worth posting sense it brought my tab back too life which i thought i would've had too sent it back and waited a month or so, And wanted others too get there tab back too life with out playing the wait game which i really hate .. lol
this worked! I was able to get rid of CWM, my tab is 100% stock again! thanks a bunch!
well, I tried installing the update from sprint and goes back to CMW and starts doing the freaking back up again!! What the heck!!! anyone can tell me how to get back to stock recovery!! this is driving me nuts!
jcaf77 said:
this worked! I was able to get rid of CWM, my tab is 100% stock again! thanks a bunch!
Click to expand...
Click to collapse
I flash the above .tar and .pit with Odin and I still can't get rid of CWM. I had CWM 3.0 working. Then I flashed a Kernel (Khasmek) with kernel flasher and the damn thing froze on the splash screen. So I odin and it doesn't do a full factory reset. CWM folder is still there. Does anbody know how to completely revert back to stock firmware?
I basically want to start over from scratch and never use Kernel flasher.
Any help will be greatly appreciated.
lphillips80 said:
I flash the above .tar and .pit with Odin and I still can't get rid of CWM. I had CWM 3.0 working. Then I flashed a Kernel (Khasmek) with kernel flasher and the damn thing froze on the splash screen. So I odin and it doesn't do a full factory reset. CWM folder is still there. Does anbody know how to completely revert back to stock firmware?
I basically want to start over from scratch and never use Kernel flasher.
Any help will be greatly appreciated.
Click to expand...
Click to collapse
Flash the zImage from the stock rom in the recovery slot using hiemdall and it will flash the stock recovery over cwm.
I performed that action and it works it does get rid of CWM but now I am still unable to install sprint updates they fail half way into it
jcaf77 said:
I performed that action and it works it does get rid of CWM but now I am still unable to install sprint updates they fail half way into it
Click to expand...
Click to collapse
I am having the exact same problem, really wish I had read your post before I attempted to get CWM on my sprint galaxy tab.
I believe the update failed for me due to mismatch baseband (EB28) and system build (DJ30), I am looking for a roto backup copy of system build EB28, if anyone have it, please help and upload!
Many thanks.
I flashed the zImage with heimdall and it still wont do a sprint system update and also I cannot do the cwm process again to format to ext4.
Sent from my SGH-T959V using XDA Premium App
lphillips80 said:
I flashed the zImage with heimdall and it still wont do a sprint system update and also I cannot do the cwm process again to format to ext4.
Sent from my SGH-T959V using XDA Premium App
Click to expand...
Click to collapse
Check out the newly leaked EA24 flasher, it will update both system and baseband to EA24 and you will be able to update after that.
Thanks technote. I used the above and worked awesome!
Sent from my SPH-P100 using XDA Premium App
okay, im farily new to the galaxy tab forums, only reason im here is because my friend bricked his tab and figured i could take a stab at it, i mean im good at fixing my galaxy s so i figured, how hard can this be. Wrong, my head is killing me because i cant figure this out. His tab is stuck in a boot loop mean it goes to the "samsung" screen and then stays there forever. I tried using odin with the stock firmware with no modem, everything went good but when it attemped to restart still nothing ? can someone please school me on how to do this properly please. Im a pretty good listener if im given descent instructions lol please by all means HELP lol

Noobie Rom ?

I have tried to install, following instruction on this site to install ROM's. I have tried Starburst and Task650. I currently have the OTA Touchwiz installed from Samsung, and Pershoot kernel 2.6.34-4-cyanogenmod installed. Every time I try it goes through the process and successfully I reboot, it boots to the Samsung Logo (Start) and I wait like 20 minutes and it does nothing, just stay at the start Samsung logo. I have done this several times on each ROM, always having to go back to a backup I did. What am I doing wrong? Why can’t I install any ROMs? I would greatly appreciate some expert advice, because I hear so many great things about Task650 I really want to give it a shot. I am an ex-iPad owner, gave to daughter as a friend had one and let me use it; feel in love with it the moment I picked it up. I have also searched the forums, but I am doing everything to the T as outlined in instructions. Had my tab for a week, it isn’t a 10.1v or I/O series. Thanks everyone in advance for helping a complete noob when it comes to android.
Sounds like a case of missing to clear the cache.
Did you wipe the cache partition and dalvic cache in the recovery menu?
After making major changes like switching between roms or kernels thats recommended and if not done might cause such an issue.
I did
I did do those steps, did the factory wipe/reset, wiped cache, wiped dalvic. Once I did those 3 steps, installed from zip, goes through the steps successfully, but when I reboot it just stay on logo. I read, it could take 5-10 min, but I have waited up to 20 and it doesn't move past that. Just see what I am doing wrong, as the 2 roms have both done that, and I have tried several times with both. Just have the stock rom with Touchwiz OTA upgrade from Samsung, and pershoots latest kernel. Thanks in advance.
bad zip file?
Is it possible the zip files are getting corrupt? Are you downloading them on your tab or on computer and transferring them over? I would also check to see if there are any errors when you flash.
Download from computer and transfer over. How can I if there are errors as once I install a ROM it just stays at the logo. After it starts to install it end with, i cant recall exactly, but it says success. Thanks in advance
In cwm when you flash there is some text readout. That is where some error messages could be seen. That text will be there before you choose reboot on the menu.
sounds like you've had some issues bro. if you do get fed up and need some help, just let me know and we can video chat through gmail or skype to get you through it and get you a custom rom.
slice2011 said:
I have tried to install, following instruction on this site to install ROM's. I have tried Starburst and Task650. I currently have the OTA Touchwiz installed from Samsung, and Pershoot kernel 2.6.34-4-cyanogenmod installed. Every time I try it goes through the process and successfully I reboot, it boots to the Samsung Logo (Start) and I wait like 20 minutes and it does nothing, just stay at the start Samsung logo. I have done this several times on each ROM, always having to go back to a backup I did. What am I doing wrong? Why can’t I install any ROMs? I would greatly appreciate some expert advice, because I hear so many great things about Task650 I really want to give it a shot. I am an ex-iPad owner, gave to daughter as a friend had one and let me use it; feel in love with it the moment I picked it up. I have also searched the forums, but I am doing everything to the T as outlined in instructions. Had my tab for a week, it isn’t a 10.1v or I/O series. Thanks everyone in advance for helping a complete noob when it comes to android.
Click to expand...
Click to collapse
Well first...are you rooted? Do you have Clockworkmod, Superuser, and Busybox?
Oh and congrats on your switch from Apple to Android
slice2011 said:
I have tried to install, following instruction on this site to install ROM's. I have tried Starburst and Task650. I currently have the OTA Touchwiz installed from Samsung, and Pershoot kernel 2.6.34-4-cyanogenmod installed. Every time I try it goes through the process and successfully I reboot, it boots to the Samsung Logo (Start) and I wait like 20 minutes and it does nothing, just stay at the start Samsung logo. I have done this several times on each ROM, always having to go back to a backup I did. What am I doing wrong? Why can’t I install any ROMs? I would greatly appreciate some expert advice, because I hear so many great things about Task650 I really want to give it a shot. I am an ex-iPad owner, gave to daughter as a friend had one and let me use it; feel in love with it the moment I picked it up. I have also searched the forums, but I am doing everything to the T as outlined in instructions. Had my tab for a week, it isn’t a 10.1v or I/O series. Thanks everyone in advance for helping a complete noob when it comes to android.
Click to expand...
Click to collapse
Maybe try in "reverse" order
Flash kernel back to stock - flash the rom you want - if that works then flash pershoots kernel
Just a thought
hy
i installed the overcome rom on my 7500, and i'm so entusiast!
Try it it's very easy!
---------- Post added at 07:21 PM ---------- Previous post was at 07:16 PM ----------
i did it in recovery, do wipe data
Yes its is rooted, cmw, superuser, and busybox all installed. Installed both roms in recovery, hold volume down and power method. Just can't figure it out, I will do the reverse suggestion and report back later tonight or tomorrow.thanks everyone for the advice/help.
no erreor s after install, think task's says success or something to that effect.
Well it finally stuck, I knew it was going right as when it was installing system files, it took like 5 minutes, the other time I did it took like 30 seconds. As per Stinky73 went back to stock Kernel, and wipe data, clear cache partition, and wipe Dalvik Cache, Thanks a million Stinky73 u da man! HELL YEAH this Rock, it is so responsive, seems a hell of a lot smoother, and apps just snap open. Task you did one outstanding job. This is coming from a noob who has no idea how much work goes into these, I am sure a lot. So from a noob to an expert EXCELLENT JOB, love my Tab that much more!!!!! Thanks everyone for the help, I am one happy camper! Now another dilemma, I saw new versions: How do I install these now that I have Tasks650 installed and working? Do I have to do the same steps above, wipe data, cache, and Dalvik? And if so what do I do next, do I do the same: Also is the BOB_WOW_Fix installed using the same method as i read flashable, sorry for the noob question, just want to get it right.
1. install zip from sdcard.
2. choose zip from sdcard.
NEW!!!- Task650's V7.1
Once again... I forgot to add "Desktop UAstring to V7.1 so flash this update after you boot up V7.1 if you want it.
Can someone please give me the proper ateps on installing the bob_wow_fix, and the 2 7.1 updates? Thanks
slice2011 said:
Can someone please give me the proper ateps on installing the bob_wow_fix, and the 2 7.1 updates? Thanks
Click to expand...
Click to collapse
There's no complete fix for BoB and WoW, its a continuous work in progress.
bob wow fix
Are you taking about the fix task posted?
What I had to do was wipe cache first then flash the zip just like you did on the rom. And bobs your uncle.
Edit:
Oh ya I would reboot after each flash just to be sure.
So as you probably read had a hell of a time getting a rom installed, followed stink'ys advice and it worked. Installed 6.0, finally, than installed the 6.1 theme update, no issues. Than downloaded the 7.1, followed op. wiped dalvik, wiped cache, and wipe data/factory restore. No errors, but when I rebooted it got stuck once again on the Samsung logo with the Galaxy Tab 10.1 print. So i do not know what the heck I am doing wrong. I got 6.0 than 6.1 updated and now I am back to my initial problem with 7.1, no I didn't use the 7.1 update one. tried 3 times, and even downloaded the fiel again, and followed the same steps task outlined, and no go. Had to restore the 6.1 from back up.
slice2011 said:
So as you probably read had a hell of a time getting a rom installed, followed stink'ys advice and it worked. Installed 6.0, finally, than installed the 6.1 theme update, no issues. Than downloaded the 7.1, followed op. wiped dalvik, wiped cache, and wipe data/factory restore. No errors, but when I rebooted it got stuck once again on the Samsung logo with the Galaxy Tab 10.1 print. So i do not know what the heck I am doing wrong. I got 6.0 than 6.1 updated and now I am back to my initial problem with 7.1, no I didn't use the 7.1 update one. tried 3 times, and even downloaded the fiel again, and followed the same steps task outlined, and no go. Had to restore the 6.1 from back up.
Click to expand...
Click to collapse
All sounds very strange...is it definitely stuck on the boot screen? These things can take anything from 5-20 minutes on initial boot, there is no definite rule for that, seems to be device related in some strange way...how long have you left it?
I am really an OCD when it comes to upgrading and always backup (nandroid or whatever) then go back to the very start before trying something new...years of PC and Mac have taught me that even tho the manufacturers say you just apply upgrades on top of previous upgrades, sooner or later they will f**k up....
I wonder why you are passing thro all the steps you are...(going thro 6.0, 6.1 etc)
I would be inclined to try going back to stock....stock whatever it was rom when you got the tab (notice you've never stated what model you have), stock kernel, nothing installed....then go direct to Tasks 7.1 (everything needed in 6.x is incorporated in 7.1) .... then, if it boots and runs, add pershoots kernel...
What do you reckon Task?? Can you chip in on this one?
Cheers, Stinky
@ slice2011.....any news?
Drpbody said:
And bobs your uncle..
Click to expand...
Click to collapse
How'd you know Bob was my uncle?
Oh wait..everybody has an uncle bob somewhere

Phone stuck on "Samsung - Custom" screen after creating TWRP backup. Help please?

Phone stuck on "Samsung - Custom" screen after creating TWRP backup. Help please?
I have an ATT S4, that has had CM 10.1 on it running flawlessly pretty much since nightlies started to get released. Decided to try going back to some TW based ROMs. Running the latest nightly, loaded up TWRP, created a backup, as I usually do before swapping roms. Created the backup fine, now it won't boot, it just sits at the Samsung screen with the lock and Custom message. Wiped cache\dalvic, even tried restoring from the backup I just created. Nothing. Tried it with the phone plugged into the computer and without being plugged in (I think I recall it being plugged into USB could cause issues in the past), and still nada. Tried pulling the battery and rebooting about 10 times. Can get into recovery and odin mode perfectly fine still. Any suggestions or ideas? Thanks
Simonzi said:
I have an ATT S4, that has had CM 10.1 on it running flawlessly pretty much since nightlies started to get released. Decided to try going back to some TW based ROMs. Running the latest nightly, loaded up TWRP, created a backup, as I usually do before swapping roms. Created the backup fine, now it won't boot, it just sits at the Samsung screen with the lock and Custom message. Wiped cache\dalvic, even tried restoring from the backup I just created. Nothing. Tried it with the phone plugged into the computer and without being plugged in (I think I recall it being plugged into USB could cause issues in the past), and still nada. Tried pulling the battery and rebooting about 10 times. Can get into recovery and odin mode perfectly fine still. Any suggestions or ideas? Thanks
Click to expand...
Click to collapse
There are no less than a dozen similar threads about similar problems already. Have you looked at those threads for a possible solution yet? You can find them by using the search function or better yet just doing a visual search of the first few pages of the "General" and "Q&A" sections. Good luck.
Sounds like a ROM and kernel issue. Try flashing a ROM with a loki'd kernel.
Tylorw1
Sent from my SAMSUNG-SGH-I337 using Tapatalk 4
Tylorw1 said:
Sounds like a ROM and kernel issue. Try flashing a ROM with a loki'd kernel.
Tylorw1
Sent from my SAMSUNG-SGH-I337 using Tapatalk 4
Click to expand...
Click to collapse
I don't see how that could be the case. I didn't flash anything. I just loaded TWRP, created a backup, and rebooted my phone. No ROM\kernel change. Nothing more than creating a backup in TWRP.
scott14719 said:
There are no less than a dozen similar threads about similar problems already. Have you looked at those threads for a possible solution yet? You can find them by using the search function or better yet just doing a visual search of the first few pages of the "General" and "Q&A" sections. Good luck.
Click to expand...
Click to collapse
I tried searching, the closest one I could find on the first few pages was this one. I just didn't see any specific to my situation because nothing was flashed. Like my response to Tylorw1, all I did was boot into recovery, create a backup, and reboot my phone. Didn't flash a ROM, change a kernel, format anything, etc...
I has this same problem... It happened after every single reboot after flashing various ROMs or anything.. I gave up and went back to CWM and haven't had the problem since :good:
Sent from my SGH-I337 using xda app-developers app
Simonzi said:
I have an ATT S4, that has had CM 10.1 on it running flawlessly pretty much since nightlies started to get released. Decided to try going back to some TW based ROMs. Running the latest nightly, loaded up TWRP, created a backup, as I usually do before swapping roms. Created the backup fine, now it won't boot, it just sits at the Samsung screen with the lock and Custom message. Wiped cache\dalvic, even tried restoring from the backup I just created. Nothing. Tried it with the phone plugged into the computer and without being plugged in (I think I recall it being plugged into USB could cause issues in the past), and still nada. Tried pulling the battery and rebooting about 10 times. Can get into recovery and odin mode perfectly fine still. Any suggestions or ideas? Thanks
Click to expand...
Click to collapse
what version of twrp? if it is 2.6.?.? then get off of it, also, what I did was pull battery for 3min, it booted fine....go back to early version of twrp...
STVERDI said:
I has this same problem... It happened after every single reboot after flashing various ROMs or anything.. I gave up and went back to CWM and haven't had the problem since :good:
Sent from my SGH-I337 using xda app-developers app
Click to expand...
Click to collapse
I've wanted to go back to CWM. That's what I had on my S3. Only thing stopping me, is all my nandroid backups for my S4 are done with TWRP, and I don't want to run into a situation where I need them, and them not being compatible
TheAxman said:
what version of twrp? if it is 2.6.?.? then get off of it, also, what I did was pull battery for 3min, it booted fine....go back to early version of twrp...
Click to expand...
Click to collapse
Nope, still on 2.5.0.2. Finally, after a third complete wipe/format and restore from the back I had created (the one that started the whole issue), it works fine. Such a huge pain in the ass.
a user had to boot back into twrp and wipe data/factory reset yesterday to fix this issue.
Simonzi said:
I've wanted to go back to CWM. That's what I had on my S3. Only thing stopping me, is all my nandroid backups for my S4 are done with TWRP, and I don't want to run into a situation where I need them, and them not being compatible
Nope, still on 2.5.0.2. Finally, after a third complete wipe/format and restore from the back I had created (the one that started the whole issue), it works fine. Such a huge pain in the ass.
Click to expand...
Click to collapse
And you have to be ****ing kidding me. I rebooted into recovery while typing my initial response, just to verify I was still on the 2.5.x.x TWRP. Booted up TWRP, verified that, choose "Reboot System", and same thing. Back to sitting at the Samsung screen. Nandroid backups or not, ditching TWRP as soon as I get it able to boot back up.
Even worse off now than when I started. After my last post, where my phone was doing the same "stuck on Samsung logo" thing, just from booting into TWRP, I decided to swap to a different recovery. Searched for "switch from TWRP to CWM", and found my own post I had made a few months ago, but never went through.
Following those instructions now, I decided on the PhilZ CWM. Head over to that thread, grab the loki'd zip, load up TWRP, and flash the zip. Now I can't even boot into recovery!! It just freezes on the Samsung screen with the blue "recovery booting" text.
Can still get into download mode, so I tried using ODIN to flash PhilZ jflteatt.tar.md5 file, and it fails.
At this point, waiting for the stock 1.6 firmware package to download, so I can just ODIN that.
If anyone has any other suggestions though, they'd be great. Have an hour to try while waiting for that to download
somebody had mentioned this...
http://forum.xda-developers.com/showpost.php?p=44629460&postcount=8
make sure you have the correct firmware and proceed as you are. likely your best bet.
Simonzi said:
Even worse off now than when I started. After my last post, where my phone was doing the same "stuck on Samsung logo" thing, just from booting into TWRP, I decided to swap to a different recovery. Searched for "switch from TWRP to CWM", and found my own post I had made a few months ago, but never went through.
Following those instructions now, I decided on the PhilZ CWM. Head over to that thread, grab the loki'd zip, load up TWRP, and flash the zip. Now I can't even boot into recovery!! It just freezes on the Samsung screen with the blue "recovery booting" text.
Can still get into download mode, so I tried using ODIN to flash PhilZ jflteatt.tar.md5 file, and it fails.
At this point, waiting for the stock 1.6 firmware package to download, so I can just ODIN that.
If anyone has any other suggestions though, they'd be great. Have an hour to try while waiting for that to download
Click to expand...
Click to collapse
Stock 1.6 firmware package?
Make sure you get the correct firmware? Go to SamMobile and get the stock firmware from there or go to Adam Outlers "Stock firmware ODIN" thread in the General section (the AMDL firmware link is in that thread you just have to look for it).
scott14719 said:
Stock 1.6 firmware package?
Make sure you get the correct firmware? Go to SamMobile and get the stock firmware from there or go to Adam Outlers "Stock firmware ODIN" thread in the General section (the AMDL firmware link is in that thread you just have to look for it).
Click to expand...
Click to collapse
Yeah, I meant 1.6gb firmware package. Just forgot the "gb". That's what I'm currently downloading, but trying to recover it with Kies while waiting.
I would like to report I had the same problem.
After changing roms and making a nandroid, and then deciding to switch roms again, I ran into the stuck at Samsung Custom with a lock boot screen. Most roms would boot up once, but a restart or power down would lead to being stuck. I was flashing through TWRP.
I went into TWRP and flashed OUDHS recovery which overrode TWRP and wiped/flashed through OUDHS a new rom.
Problem solved.
S3 at&t stuck in TWRP booting screen.
xBeerdroiDx said:
a user had to boot back into twrp and wipe data/factory reset yesterday to fix this issue.
Click to expand...
Click to collapse
Im new to custom roms, I pressed ok for an update on my phone, after the update was complete my phone shut off and booted into TWRP and now I can't get back to my android screen nor make calls etc. HELPPPPPPPP PLEASSSSSEE I have been trying to fix my phone since july and I have been using this cheap phone that don't even get internet. I have an S3 1747 at&t
Lnjames said:
Im new to custom roms, I pressed ok for an update on my phone, after the update was complete my phone shut off and booted into TWRP and now I can't get back to my android screen nor make calls etc. HELPPPPPPPP PLEASSSSSEE I have been trying to fix my phone since july and I have been using this cheap phone that don't even get internet. I have an S3 1747 at&t
Click to expand...
Click to collapse
Wrong forum. Please go to the s3 section with your question.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Had this problem just now, solved it by fixing permissions.
I am running an MDL based S4, and screwed the pooch. I was going to wipe the internal storage and made the mistake of doing it through TWRP 2.5. Now, I have the same problem of being stuck on the custom boot screen. I have tried to change from TWRP to OUDHS Recovery, but still boot loops to Custom screen. I have tried fresh installs of 4.2 ROMs and 4.4.2 Google Editions. Do I need to flash via ODIN?
Flame away....I know better than this!!!!
Help would be greatly appreciated.
Sent from my GT-N8013 using Tapatalk 4

[Q] Help a noob, cannot boot after trying to flash stock rom

So I'm pretty desperate and I apologize if similar info was posted somewhere else. I've been researching several hours but couldn't find anything.
I originally installed CM11 and decided to experiment with a different rom TriForce ROM [TouchWiz]. I put the zip file on my SD card and booted into clockworkmod it gave an error of bad zip. I tried different usb port to transfer the zip, downloaded it multiple times with no result. So I decided to try a different rom Stock_Rooted_Deodexed_MF9_Rom.zip. The installation finished but the phone would not boot.
Recently I flashed the stock rom from odin, it finished successfully but still not boot, Galaxy sreen lights up quickly and that's it.
rmngorelov said:
So I'm pretty desperate and I apologize if similar info was posted somewhere else. I've been researching several hours but couldn't find anything.
I originally installed CM11 and decided to experiment with a different rom TriForce ROM [TouchWiz]. I put the zip file on my SD card and booted into clockworkmod it gave an error of bad zip. I tried different usb port to transfer the zip, downloaded it multiple times with no result. So I decided to try a different rom Stock_Rooted_Deodexed_MF9_Rom.zip. The installation finished but the phone would not boot.
Recently I flashed the stock rom from odin, it finished successfully but still not boot, Galaxy sreen lights up quickly and that's it.
Click to expand...
Click to collapse
Restore from nandroid backup. I hope you made one. Try going into recovery do a factory reset and wipe all cache and data and what not and then install a ROM from Odin.
rmngorelov said:
So I'm pretty desperate and I apologize if similar info was posted somewhere else. I've been researching several hours but couldn't find anything.
I originally installed CM11 and decided to experiment with a different rom TriForce ROM [TouchWiz]. I put the zip file on my SD card and booted into clockworkmod it gave an error of bad zip. I tried different usb port to transfer the zip, downloaded it multiple times with no result. So I decided to try a different rom Stock_Rooted_Deodexed_MF9_Rom.zip. The installation finished but the phone would not boot.
Recently I flashed the stock rom from odin, it finished successfully but still not boot, Galaxy sreen lights up quickly and that's it.
Click to expand...
Click to collapse
Make sure you're using roms for your version of your phone. the MF9 bootloader is really old and probably wont install anymore. My phone did this before and I thought I bricked it, but I kid you not I took the battery out and removed the SIM card and rebooted and it booted up just fine. May not work for you, but I suggest you go back to update stock firmware then try again. If you're using the triband model, there's a post around here somewhere with confirmed roms that wont brick your device. I'm currently using the Google Play Edition Stock ROM and it's working GREAT.
Link for new firmware (NG5 Firmware): https://mega.co.nz/#F!0JdRkIZR!AqqKdbvba_Hpg5VrCmrbPw
i7vSa7vi7y said:
Restore from nandroid backup. I hope you made one. Try going into recovery do a factory reset and wipe all cache and data and what not and then install a ROM from Odin.
Click to expand...
Click to collapse
I restored to this stock ROM before and everything worked well. Currently I can't boot into recovery, Samsung flashes once and that's it, that's why I'm desperate the only thing I can do is boot in to download mode for odin.
silentdeath631 said:
Make sure you're using roms for your version of your phone. the MF9 bootloader is really old and probably wont install anymore. My phone did this before and I thought I bricked it, but I kid you not I took the battery out and removed the SIM card and rebooted and it booted up just fine. May not work for you, but I suggest you go back to update stock firmware then try again. If you're using the triband model, there's a post around here somewhere with confirmed roms that wont brick your device. I'm currently using the Google Play Edition Stock ROM and it's working GREAT.
Link for new firmware (NG5 Firmware):
Click to expand...
Click to collapse
Does it matter that I can't get into recovery to clear the cache first before trying new roms?
silentdeath631 said:
Make sure you're using roms for your version of your phone. the MF9 bootloader is really old and probably wont install anymore. My phone did this before and I thought I bricked it, but I kid you not I took the battery out and removed the SIM card and rebooted and it booted up just fine. May not work for you, but I suggest you go back to update stock firmware then try again. If you're using the triband model, there's a post around here somewhere with confirmed roms that wont brick your device. I'm currently using the Google Play Edition Stock ROM and it's working GREAT.
Link for new firmware (NG5 Firmware):
Click to expand...
Click to collapse
Maybe I'm doing something foolish but every time I try to download files from the link you gave I get a decryption error so I can't download them zip or original.
rmngorelov said:
I restored to this stock ROM before and everything worked well. Currently I can't boot into recovery, Samsung flashes once and that's it, that's why I'm desperate the only thing I can do is boot in to download mode for odin.
Click to expand...
Click to collapse
Just hold home power and volume up. Right when you see text at the top left let go. You have to have the right timing
i7vSa7vi7y said:
Just hold home power and volume up. Right when you see text at the top left let go. You have to have the right timing
Click to expand...
Click to collapse
After almost eight hours of troubleshooting I finally got it to work.
I've tried flashing clockworkmod several times to see if I could get into recovery with no result so I gave up on that and I flashed the newest stock rom I could find L720VPUFNG2_L720SPTFNG2_SPR and it was still not booting. Than I thought maybe twerp would make a difference and god almighty it finally booted! I felt as if I gave birth to a child after eight hours of labor!
Now I'm extremely paranoid about touching anything because it took me forever to do this. Does anyone know why flashing twerp would make such a difference? I know this sort of stuff can get extremely complicated but I'd like to try to understand.
I hope my foolish agony contributed to this community if not in any other way except by the comedic relief caused by my ignorance.
rmngorelov said:
After almost eight hours of troubleshooting I finally got it to work.
I've tried flashing clockworkmod several times to see if I could get into recovery with no result so I gave up on that and I flashed the newest stock rom I could find L720VPUFNG2_L720SPTFNG2_SPR and it was still not booting. Than I thought maybe twerp would make a difference and god almighty it finally booted! I felt as if I gave birth to a child after eight hours of labor!
Now I'm extremely paranoid about touching anything because it took me forever to do this. Does anyone know why flashing twerp would make such a difference? I know this sort of stuff can get extremely complicated but I'd like to try to understand.
I hope my foolish agony contributed to this community if not in any other way except by the comedic relief caused by my ignorance.
Click to expand...
Click to collapse
Depends what recovery you had and what version. I personally like Philz touch recovery but TWRP is good. Now wipe and flash a ROM my friend or restore a backup
rmngorelov said:
After almost eight hours of troubleshooting I finally got it to work.
I've tried flashing clockworkmod several times to see if I could get into recovery with no result so I gave up on that and I flashed the newest stock rom I could find L720VPUFNG2_L720SPTFNG2_SPR and it was still not booting. Than I thought maybe twerp would make a difference and god almighty it finally booted! I felt as if I gave birth to a child after eight hours of labor!
Now I'm extremely paranoid about touching anything because it took me forever to do this. Does anyone know why flashing twerp would make such a difference? I know this sort of stuff can get extremely complicated but I'd like to try to understand.
I hope my foolish agony contributed to this community if not in any other way except by the comedic relief caused by my ignorance.
Click to expand...
Click to collapse
im having similar issues. which version of TWRP worked for you?
thank you
fearthemarchx said:
im having similar issues. which version of TWRP worked for you?
thank you
Click to expand...
Click to collapse
I recommend flashing the newest one here using odin
http://teamw.in/project/twrp2
Then once you are able to boot into recovery go to wipe and perform both factory reset and format data. Then install whatever rom you like, I used Sprint Galaxy S4 SPH-L720 VPUFNAE (Androdi 4.4.2) found here
http://galaxys4root.com/galaxy-s4-stock-firmware/ (or maybe find a newer stock rom if this one gives you errors)
Just copy the zip file to the phone, boot into twrp, do wipe factory reset again, select install then select the zip in whatever directory and you should be good to go. Make sure you do a back up in twrp once you get the phone to boot so you can always revert to stock.
I hope I was thorough enough that some of the information was useful. Let me know if you need any more help.
only certain recoveries will stick. ive tried the most recent twrp, with no luck. only a few versions of philztouch work.
Sent from my LGL34C using XDA Free mobile app
fearthemarchx said:
only certain recoveries will stick. ive tried the most recent twrp, with no luck. only a few versions of philztouch work.
Sent from my LGL34C using XDA Free mobile app
Click to expand...
Click to collapse
Format with philztouch that works then try flashing a new stock rom with odin. That should bring everything back to stock including the recovery.
ive tried. when i flash rom via odin i only get a blue "recovery booting" at the top of boot screen. even when i only power on, not into recovery. im going to attempt to flash rom provided in previous post via philz.
Sent from my LGL34C using XDA Free mobile app
fearthemarchx said:
ive tried. when i flash rom via odin i only get a blue "recovery booting" at the top of boot screen. even when i only power on, not into recovery. im going to attempt to flash rom provided in previous post via philz.
Sent from my LGL34C using XDA Free mobile app
Click to expand...
Click to collapse
You're in download mode when you flash from odin right? If you your getting an error flashing, try a different stock rom after reformating/resetting to factory (it's crucial to clear the cache before trying a different rom). I had to try a few roms before I found one that worked.

[Q] Galaxy S5 Dev Edition (Verizon) TOTALLY WIPED

im in big trouble on this one, i rarely EVER ASK FOR HELP, but this time im done. i was on fusion 4.4.2 and decided i wanted to try lollipop. so i found the dev edition roms and tried loaading the with philz recovery. got it up and running but only had data NO MOBILE SERVICE. so i started loading different roms with no luck, tried different kernels thinking i mismatched them. still no luck so i tried couple different modems NO LUCK!!!!!!!!!!!!! got totally lost, upset and agarvated. well thats when i made a BIG BIG MISTAKE. i boot in philz touch and went to advanced menu i formatted EVERYTHING data, system, media EVERYTHING. now i load (thru odin) fresh Philz recovery found the ODIN TO STOCK thread have tried loading ALL the dev files complete stock firm, the kernel modems EVERYTHING. it takes on the phone but when it reboots gets stuck on GALAXY S5 sceen. still says custom and has unlock but wont boot up. so i go back into recovery go to load zip menu and alls thats on my phone is /0 folder and /clockmod folder. so the phone is wiped out and wont take anything thru odin. i can still get to philz but no way to get zip into phone to load. PLEASE TELL ME i didnt lock my bootloader????????? i really need some help here been working on this thing for 3days now. thanks in advance

			
				
1tonv said:
im in big trouble on this one, i rarely EVER ASK FOR HELP, but this time im done. i was on fusion 4.4.2 and decided i wanted to try lollipop. so i found the dev edition roms and tried loaading the with philz recovery. got it up and running but only had data NO MOBILE SERVICE. so i started loading different roms with no luck, tried different kernels thinking i mismatched them. still no luck so i tried couple different modems NO LUCK!!!!!!!!!!!!! got totally lost, upset and agarvated. well thats when i made a BIG BIG MISTAKE. i boot in philz touch and went to advanced menu i formatted EVERYTHING data, system, media EVERYTHING. now i load (thru odin) fresh Philz recovery found the ODIN TO STOCK thread have tried loading ALL the dev files complete stock firm, the kernel modems EVERYTHING. it takes on the phone but when it reboots gets stuck on GALAXY S5 sceen. still says custom and has unlock but wont boot up. so i go back into recovery go to load zip menu and alls thats on my phone is /0 folder and /clockmod folder. so the phone is wiped out and wont take anything thru odin. i can still get to philz but no way to get zip into phone to load. PLEASE TELL ME i didnt lock my bootloader????????? i really need some help here been working on this thing for 3days now. thanks in advance
Click to expand...
Click to collapse
Factory reset after flashing back to stock?
*Detection* said:
Factory reset after flashing back to stock?
Click to expand...
Click to collapse
tried that AT LEAST three times no luck
You should be able to recover from any problem scenario you cause in recovery, using ODIN
Stock ROM from sammobile, maybe you'll need a PIT file to re-partition the phone, there is a thread on XDA in these S5 forums with PIT files
EDIT - 2nd post
http://forum.xda-developers.com/showthread.php?t=2737448
After wiping everything AGAIN and letting it sit on galaxy screen it finally booted up. 1st thing I did was made a backup now I guess I'm gonna do A BUNCH MORE READING them I'll get this thing rooted and try some other rooms. Seems there's the A08 I'm on then NK2, N12 and other versions and seems only certain roms use certain kernels and firmware. So I need to get the right configuration for each b4 even trying to install them or they don't boot up.
A lot more to this galaxy s5 unlike my Nexus in the past. B4 just load the rom and go. With this s5 a lot more things to do and know about. All part of the game I guess

Categories

Resources