HTC Evo Shift 4G Touch Screen Digitizer Repair Guide - EVO Shift 4G General

Does the outer touchscreen of your Evo Shift 4G has been damaged or cracked? This take apart repair guide will show the steps on how to properly disassemble and repair a damaged touchscreen digitizer for your HTC Evo Shift 4G.
This guide will help you to install the following HTC Evo Shift 4G part(s):
HTC Evo Shift 4G Touch Screen Digitizer Replacement
Tools Required:
Safe Open Pry Tool
Small Phillips Screwdriver
T5 Torx Screwdriver
Hot Air Gun / Hair Dryer (optional)
HTC Evo Shift 4G apart guide:
Step one is to remove the back battery cover, batter, and memory card. Once that is done remove the four Torx T5 screws located in the back housing. Use a safe open pry tool to release the clips located around the back housing and then remove the housing from the phone.
Remove the motherboard by releasing the "pop" connector and removing the two small phillips screws. Once the motherboard is removed, remove the eight small phillips screws located under the keyboard.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1​
With the keyboard removed, use a small phillips screwdriver to remove the two screws located on the plastic covers at the top and bottom of the phone. Remove the covers to reveal two more hidden small phillips screws, remove them as well.
Figure 2​
Use a hair dryer or heat gun to warm the adhesive and carefully remove the flex cable on the sliding portion of the phone. Release the two jaw connectors and ease off the ribbon cable from the back of the LCD screen.
Release the other flex cable from the back of the LCD screen and carefully remove the LCD screen from the rest of the phone. Remove the flex cable from the front housing and touch screen.
Figure 3​
Warm the adhesive and use a safe pry tool to lift the touch screen from its housing. Carefully ease the ribbon cable through the frame and replace your touch screen.
Reverse the instructions above to reassemble your phone.

We also have a Evo Shift 4G video guide available which may be useful in correlation to the above guide.

I'm going to use your Doubleshot guilds soon, because my screen is trashed. It's good to see your covering many devices
Sent from my myTouch 4G Slide using Tapatalk 2

Stickied, thanks for doing these guides.

strapped365 said:
I'm going to use your Doubleshot guilds soon, because my screen is trashed. It's good to see your covering many devices
Sent from my myTouch 4G Slide using Tapatalk 2
Click to expand...
Click to collapse
No problem. Glad we can help.

hey my touch screen goes haywire for no reason...sometimes wont let me touch anything or presses random icons, unresponsive. how do i fix this? what do i have to replace?

erivera1031 said:
hey my touch screen goes haywire for no reason...sometimes wont let me touch anything or presses random icons, unresponsive. how do i fix this? what do i have to replace?
Click to expand...
Click to collapse
Do you hear a Crunching, or strange sound when you Open / Close the keyboard ? If you do then it is most likely the Flex Cable that has worn out. It is a fairly common issue with the Shift. But it can be repaired if that is the issue.

prboy1969 said:
Do you hear a Crunching, or strange sound when you Open / Close the keyboard ? If you do then it is most likely the Flex Cable that has worn out. It is a fairly common issue with the Shift. But it can be repaired if that is the issue.
Click to expand...
Click to collapse
i dont hear anything now when sliding it up and down...but i do remember hearing that kind of noise when the touchscreen 1st started acting up a few weeks ago. where would i be able to get a replacement from?

erivera1031 said:
i dont hear anything now when sliding it up and down...but i do remember hearing that kind of noise when the touchscreen 1st started acting up a few weeks ago. where would i be able to get a replacement from?
Click to expand...
Click to collapse
You can pick up the Flex Cable from a few different places. You can get it on Ebay EVO Shift Flex Cable , or Amazon EVO Shift Flex Cable. It's fairly straight forward to install. Just be sure and take your time.

erivera1031 said:
i dont hear anything now when sliding it up and down...but i do remember hearing that kind of noise when the touchscreen 1st started acting up a few weeks ago. where would i be able to get a replacement from?
Click to expand...
Click to collapse
You can find all the Evo Shift 4G Replacement parts here including screen replacements and the main flex slide cable replacement - HTC Evo Shift Replacement Parts

Very Kool . Thank you. Bookmarked it for the future

prboy1969 said:
You can pick up the Flex Cable from a few different places. . It's fairly straight forward to install. Just be sure and take your time.
Click to expand...
Click to collapse
Before i buy it just one more question. The touch screen actually works better when its opened. I was reading about the flex cable and it said that if its opened and not working properly. Should i play it safe and replace the touchscreen digitizer and the flex cable? Or does the touchscreen digitizer come with the replacement flex cable? Im pretty new to this and gotta have a working phone at all times for work.

erivera1031 said:
Before i buy it just one more question. The touch screen actually works better when its opened. I was reading about the flex cable and it said that if its opened and not working properly. Should i play it safe and replace the touchscreen digitizer and the flex cable? Or does the touchscreen digitizer come with the replacement flex cable? Im pretty new to this and gotta have a working phone at all times for work.
Click to expand...
Click to collapse
The digitizer has a flex cable but not the main flex cable. I would not like to say which part you need for sure what the issue is without seeing the device. However replacing both would fix the issue.
I would recommend switching the one you think is causing the issue first, and then replace the other if needed. Optionally you can just swap both however you could be buying something you don't need.

repairsuniverse said:
The digitizer has a flex cable but not the main flex cable. I would not like to say which part you need for sure what the issue is without seeing the device. However replacing both would fix the issue.
I would recommend switching the one you think is causing the issue first, and then replace the other if needed. Optionally you can just swap both however you could be buying something you don't need.
Click to expand...
Click to collapse
Ok..so far today i have seen delays in unlocking the phone...and when the phone is not on open i cant touch anything on the top portion of the screen and cant touch to zoom...and when i try to touch on occasions it zooms in and out. Hope this can help u diagnose....from what i tell to me looks like the main flex cable...but im no expert...

erivera1031 said:
Ok..so far today i have seen delays in unlocking the phone...and when the phone is not on open i cant touch anything on the top portion of the screen and cant touch to zoom...and when i try to touch on occasions it zooms in and out. Hope this can help u diagnose....from what i tell to me looks like the main flex cable...but im no expert...
Click to expand...
Click to collapse
It defiantly sounds like it's the Main Flex Cable. Funny thing is I just did one Today. Just not on an EVO Shift. It was on a Touch Pro2 . Know someone who's still rocking one.

prboy1969 said:
It defiantly sounds like it's the Main Flex Cable. Funny thing is I just did one Today. Just not on an EVO Shift. It was on a Touch Pro2 . Know someone who's still rocking one.
Click to expand...
Click to collapse
hey got another question sorry to sound so annoying but i manged to mess up the phone some more...smh it fell in the toilet. it didn't really get wet cuz the leather pouch it was in took most of the water damage. but i managed to get it dry and the phone looks like its completely dry but when i turn it on it looks like there oil like stains on the screen now. is it say to say that im going to need a new lcd screen...i shut the phone back off and am going to let it dry some more just in case. but i did turn it on and it worked perfectly fine just that the stains were there.
If it is the LCD screen do i have to order a LCD screen and the digitizer screen replacement? ive already ordered a new main flex cable and just waiting on delivery. Thanks For that!! :laugh:

I got a strange problem in my evo shift. I am not able to dial 7,8 and 9 numbers. The touch of that area is not responding properly, I am also getting problem in unlocking the screen due to slider in the same area. Rest of the touch is fine.

erivera1031 so sorry about the late response. Completely missed the post. But it sounds like to me your going to have to replace at least the LCD. I personally would do both.
abhishekky said:
I got a strange problem in my evo shift. I am not able to dial 7,8 and 9 numbers. The touch of that area is not responding properly, I am also getting problem in unlocking the screen due to slider in the same area. Rest of the touch is fine.
Click to expand...
Click to collapse
Is anything going on ?
TEAM MiK
MikROMs Since 3/13/11

It's running on newSENSE RC2 rom. Only a certain area is not responding my touch( dialer no. 7,8,9) rest is all good. Phone is running very smooth.

abhishekky said:
It's running on newSENSE RC2 rom. Only a certain area is not responding my touch( dialer no. 7,8,9) rest is all good. Phone is running very smooth.
Click to expand...
Click to collapse
Did you do a FULL Wipe before flashing the Rom ? Are there any other issues occurring ?
TEAM MiK
MikROMs Since 3/13/11

Related

Dust under the Screen!

Well, I just noticed earlier today that I have a bunch of dust forming in the bottom left had side of the screen. Looks like between digitizer and LCD. Already called in an RMA. Pics to follow (once wife is home with camera).
Here is the pic.
Bump, for everyone to see the pic.
I've heard of dust getting under the screen, but damn that's pretty bad. Have you tried calling TMO, and have them exchange it for a new phone? I just can't see why they wouldn't do it. Plus, you're still under the 14 day exchange period, no questions asked.
WilliamStern said:
I've heard of dust getting under the screen, but damn that's pretty bad. Have you tried calling TMO, and have them exchange it for a new phone? I just can't see why they wouldn't do it. Plus, you're still under the 14 day exchange period, no questions asked.
Click to expand...
Click to collapse
Yeah, sorry, to be more specific, for employees (me) you have to RMA the phone, then once received and verified, they will send you another. Yes, its a BS process, so as a customer, you don't have it too bad! Haha, anyways, process is in motion.
I thought I was the only one! While, not as bad as yours I have debris collecting in the same spot! I am sending both phones I got back. I am going to use this post to demonstrate that this is potentially a flaw in the design. What a bummer, I love this phone but I can't afford for there to be a gap for dust to enter under the screen. So glad I saw this post.
There are multiple light leaks around the plastic housing surrounding the touch screen. Inspect the seam surrounding the top portion of the phone carefully while the display has a white web page up. My wife's MT3G Slide has four big gaps that can bee seen on the seam of the plastic housing surrounding the screen. Mine has 3 of theses gaps one of which has already allowed dust in under my screen. I cannot believe that these flaws were not found upon inspection after the units were assembled. I am so disappointed; I was really enjoying the phone. Thank goodness I am still in my buyers remorse. If this would have happened in a warranty situation I would be stuck in a loop of refurbished devices with the same issue all while being stuck in a new 2 year contract. Dodging a bullet on this one.
NJAZ said:
There are multiple light leaks around the plastic housing surrounding the touch screen. Inspect the seam surrounding the top portion of the phone carefully while the display has a white web page up. My wife's MT3G Slide has four big gaps that can bee seen on the seam of the plastic housing surrounding the screen. Mine has 3 of theses gaps one of which has already allowed dust in under my screen. I cannot believe that these flaws were not found upon inspection after the units were assembled. I am so disappointed; I was really enjoying the phone. Thank goodness I am still in my buyers remorse. If this would have happened in a warranty situation I would be stuck in a loop of refurbished devices with the same issue all while being stuck in a new 2 year contract. Dodging a bullet on this one.
Click to expand...
Click to collapse
I tried saying this in a post and people just made fun of me for being "anal retentive." I'm glad someone else is bringing this up. It is a huge flaw in design.
boldfacelies said:
I tried saying this in a post and people just made fun of me for being "anal retentive." I'm glad someone else is bringing this up. It is a huge flaw in design.
Click to expand...
Click to collapse
You were dead on with this. I thought you were referring to the hard buttons below the screen. Speaking of those buttons; that is also a design flaw as it appears dust can get under the screen there as well. As one pushes down those buttons it exposes the edge of the touch screen. I should have taken your words more seriously instead I was dumbstruck by what is an otherwise great phone.
Just checked my screen in the sun ... dust everywhere under the screen. Bye bye beautiful Espresso; you are fatally flawed.
Ahh, I found a pin sized hole under the slide behind G button. Also if you open the slide, and use your phone that it turns on the light you will notice light inside the micro usb connector. I am not sure if this means that dust can pass through it also.
Will post pic of said pinhole later when it gets a little dark here. Will try blowing in some baby powder into that hole to see if it does get into the screen.
EDIT: Pics of pinhole behind G button at the back of the slide.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Photo of phone with LCD on. Noticed the pinhole with some light showing thru and the micro usb connector showing some light.
Photo of the phone with display off.
EDIT: I might bring to T-Mo store for replacement but not giving up on this phone. Goodluck with the Samsung S.
Just posted in the MT3GS defective thread: this might be a larger defect than just the Slides. There's a bunch of Evo people talking about the same issue with their phones on the htc forums and the androidforums: glass is separating due to potentially faulty adhesive.
N1M1TZ said:
EDIT: I might bring to T-Mo store for replacement but not giving up on this phone. Goodluck with the Samsung S.
Click to expand...
Click to collapse
Who's getting a Galaxy S? I'm not.
I don't think the light leaks are as big an issue as I thought, so long as the adhesive seal between the digitizer and LCD is intact there shouldn't be any way for dust to get into the screen.
Hey, what kind is and where did you get that case? Looks cool!
N1M1TZ said:
Ahh, I found a pin sized hole under the slide behind G button. Also if you open the slide, and use your phone that it turns on the light you will notice light inside the micro usb connector. I am not sure if this means that dust can pass through it also.
Will post pic of said pinhole later when it gets a little dark here. Will try blowing in some baby powder into that hole to see if it does get into the screen.
EDIT: Pics of pinhole behind G button at the back of the slide.
Photo of phone with LCD on. Noticed the pinhole with some light showing thru and the micro usb connector showing some light.
Photo of the phone with display off.
EDIT: I might bring to T-Mo store for replacement but not giving up on this phone. Goodluck with the Samsung S.
Click to expand...
Click to collapse
That pin hole is on the opposite side of where my dust issue is. Strange.
NJAZ said:
Who's getting a Galaxy S? I'm not.
I don't think the light leaks are as big an issue as I thought, so long as the adhesive seal between the digitizer and LCD is intact there shouldn't be any way for dust to get into the screen.
Hey, what kind is and where did you get that case? Looks cool!
Click to expand...
Click to collapse
Thats the one offered by tmobile, black back, chrome front bezel. Has a removable belt clip, so that is why you see a little circle in the middle.
I had this happen to the first slide I picked up but luckily I noticed it fairly quick and took it back the very next day. Now the replacement I have is having the same issue, granted it's 1 spec of dust under the screen but I know it will get worse with time and I'm debating on whether or not I will just return it and go back to my G1.
Mine has it now too! Just noticed it in the sun on the way into work - Mine is going to get swapped out today too...
This is a major drag!!!
My nexus has this same issue so do many others. Some people are having a hard time getting HTC to replace because of unlocked bootloaders. On the n1 the bottom left corner of the screen feels like it is not glued down all the way and dust goes under. Some are using a hair dryer to warm up the corner and pushing down on the screen to help it glue down all the way. HTC fixed mine and then when I got it back the screen was even more loose and I have more dust now than before. I'm going to wait longer before I send it back again. Hopefully this mts doesn't start doing the same thing.
I started a thread about this over in the tmo forums. It appears that it has gotten the attention of a moderator over there. If you would like to add your story to it please feel free as well as post a picture or two of the dust your screen has trapped.
Apparently I can't post links because my account hasn't been verified. The thread isn't too hard to find over there, promise.
setzer715 said:
Well, I just noticed earlier today that I have a bunch of dust forming in the bottom left had side of the screen. Looks like between digitizer and LCD. Already called in an RMA. Pics to follow (once wife is home with camera).
Here is the pic.
Click to expand...
Click to collapse
holy crap stop hiding your phone in the litter box!
If you turn the back light off and shine a flashlight at the screen at an angle you see this very well!
Here is mine:
I don't work in a dusty environment either, probably from my pocket. Plastic pocket protectors anyone??

Google Nexus One Screen Repair Guide

Does your Google Nexus One outer screen was cracked or damaged? Also having problem with the display? This written repair guide shows how to disassemble your Google Nexus One cell phone quickly and safely.
This guide will help you to install the following Google Nexus One parts:
Google Nexus One LCD Screen Replacement
Google Nexus One Touch Screen Digitizer Replacement
Tools Required:
Safe Open Pry Tool
Small Phillips Screwdriver
T5 Torx Screwdriver
Adhesive Strips (For Touch Screen Repair)
Google Nexus One Take apart guide:
In order to disassemble a Google Nexus One phone first of all you need to remove the battery cover (rear back cover) of the phone.
After the removal of the battery cover you should be able to see three screws - a Phillips screw at the left-middle side and two T5 screws at the top-left corner and top-right corner. Remove all three screws using the respective screwdrivers. Remember to note the positions of screws for the reassembly.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1​
After removing the three screws, use a pry tool to pry off the frame (battery tray).
Now pry the bottom cover off using the pry tool again, this would be slightly difficult as it is held tighter.
There will be two more T5 screws to be removed after the bottom cover comes off. These will be located at bottom left and bottom right corners of the phone. Remove both of these screws using the Torx 5 Screwdriver
Use the pry tool again to pry the bottom frame off.
You will now have to remove two more Phillips screws using the small Phillips screw driver. These screws will be positioned at bottom-left and top-left corners of the phone.
Undo the three flex connections which can be found at the lower-right half of the phone. You can use the pry tool to achieve this.
Figure 2​
Undo the coaxial cable connection which will be located at the upper-left side of the phone.
After you have undone the flex connections and the coaxial cable, you can pry the top board off to unclip it.
Figure 3​
Remove the volume button.
Unhook the main board from the peg and then push it up and out of the phone. Note, the rubber microphone channel might fall out. Put it aside and don't lose it.
Upon removal of the main board you will find three more screws almost inline at the bottom end of the phone which are required to be removed to free the trackball assembly beneath the plate.
After removing the three screws lift this plate to free the trackball assembly (this is similar to that of Blackberry trackball).
Loosen the tape holding the LCD in place.
Figure 4​
Free the flex connector from the LCD. It’s held on with tape.
Now the LCD can come out. Carefully unclip it using the pry tool (you can use the pry tool for this).
Your Nexus one is now fully disassembled. Reverse the instructions above to reassemble your phone.
Wow, great guide, that's what I need!
My screen got cracked, but the phone and touch still work. So this means i need to replace only the lcd and NOT the digitizer?
Step by Step Video Guide
http://www.youtube.com/watch?v=hTRXSMQ-GJY
ultra99 said:
Wow, great guide, that's what I need!
My screen got cracked, but the phone and touch still work. So this means i need to replace only the lcd and NOT the digitizer?
Click to expand...
Click to collapse
If the outside glass is cracked then you need the touch screen digitizer replacement.
If your image is bad then you need the LCD screen replacement.
If both your outside glass is cracked and you have a bad image then sadly you need both the touch screen digitizer and LCD screen replacements.
Hope this clears things up. Let us know if you have further questions.
repairsuniverse said:
If the outside glass is cracked then you need the touch screen digitizer replacement.
If your image is bad then you need the LCD screen replacement.
If both your outside glass is cracked and you have a bad image then sadly you need both the touch screen digitizer and LCD screen replacements.
Hope this clears things up. Let us know if you have further questions.
Click to expand...
Click to collapse
THe image and touch are fine, so maybe it's the outside screen?
I already bought this: http://www.ebay.com/itm/270940310857?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Is that the wrong item?
ultra99 said:
THe image and touch are fine, so maybe it's the outside screen?
I already bought this:
Is that the wrong item?
Click to expand...
Click to collapse
That is the correct part to replace the cracked glass. However it looks as though its a cheap imitation part which are common on eBay. But providing it works it will fix your cracked glass issue.
Good luck, i recorded all 45 steps on the vidz i posted to youtube if you want someone to keep you company, granted the steps i posted are sort of tedious and over cautious... and people complain i replaced the touchscreen really slowwwly, but eh, at least its done !
---------- Post added at 11:21 AM ---------- Previous post was at 11:12 AM ----------
Will repair universe have a digitizer repair guide for the Samsung Galaxy Nexus?
Yes. We actually already have a guide for the Samsung Galaxy Nexus S.
A great companion to this written guide is our Nexus One video repair guide. Using it while referring to the guide above is a great way to insure a quick repair is made. We also have the guide above in a downloadable format so you can easily print and refer to while preforming a screen repair, etc.
Need urgent help
Hi!! first of all amazing guide. THank YOU!! This is my first post here and i dont know much about phones.
The thing is last week my nexus one fell from my pocket and its screen went blank. NO Display. Although if there is an incoming call i can slide on the screen , unlock it and talk but cant see anything
So, here is my question. To repair my phone do i need to buy a touch screen digitizer or LCD??
Need help asap...handicapped without my phone..
coolestchap143 said:
Hi!! first of all amazing guide. THank YOU!! This is my first post here and i dont know much about phones.
The thing is last week my nexus one fell from my pocket and its screen went blank. NO Display. Although if there is an incoming call i can slide on the screen , unlock it and talk but cant see anything
So, here is my question. To repair my phone do i need to buy a touch screen digitizer or LCD??
Need help asap...handicapped without my phone..
Click to expand...
Click to collapse
Hi,
If you are getting no image on the screen then you will need the LCD screen replacement to fix your device. You can find this part here - http://www.repairsuniverse.com/google-nexus-one-replacement-screens-parts.html
I can't see no where to ask questions. Not a noob just in need of desperate help. My sisters n1 just got stuck in hboot with the white screen. I can get into recovery but that's about it. Can anyone help Me!! I've been pulling my hair out over 2 damn hours!!!!!!!!
Sent from my GT-I9100 using xda premium
androidkid311 said:
I can't see no where to ask questions. Not a noob just in need of desperate help. My sisters n1 just got stuck in hboot with the white screen. I can get into recovery but that's about it. Can anyone help Me!! I've been pulling my hair out over 2 damn hours!!!!!!!!
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
What caused this. Was this following opening the device or a drop?
repairsuniverse said:
What caused this. Was this following opening the device or a drop?
Click to expand...
Click to collapse
She doesn't even know. She knows nothing about android. Just how to make calls and send texts lol. I will take a picture when she gets back and upload it in the Q&A section I didn't see earlier (slaps forehead). Thanks for your reply
Sent from my GT-I9100 using xda premium
androidkid311 said:
She doesn't even know. She knows nothing about android. Just how to make calls and send texts lol. I will take a picture when she gets back and upload it in the Q&A section I didn't see earlier (slaps forehead). Thanks for your reply
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
No problem.
Screen Repair Question
Wonderful technicians of Repairs Universe,
I purchased a Nexus One LCD Screen from Repairs Universe, and followed your step by step replacement instructions. The new screen has been installed, and even so, when I boot the phone, the screen never turns on. I can feel the phone vibrate, and it seems to respond to touch commands. However, I am still unable to see the screen with the replacement.
I was just wondering if you had any further suggestions for me. If you could, please email me with your reply. [email protected]
I purchased the screen last week, and installed it on Friday 05/10/13
Any help you could provide would be greatly appreciated!
Thank you!
coolestchap143 said:
Hi!! first of all amazing guide. THank YOU!! This is my first post here and i dont know much about phones.
The thing is last week my nexus one fell from my pocket and its screen went blank. NO Display. Although if there is an incoming call i can slide on the screen , unlock it and talk but cant see anything
So, here is my question. To repair my phone do i need to buy a touch screen digitizer or LCD??
Need help asap...handicapped without my phone..
Click to expand...
Click to collapse
It sounds like it will most likely need a new LCD screen. Good luck!
Today i win an auction from ebay.de HTC Google Nexus One for only 11.50 Euro !
I already have an HTC Google Nexus One phone, and now i have to repair this one
fancyfree said:
Today i win an auction from ebay.de HTC Google Nexus One for only 11.50 Euro !
I already have an HTC Google Nexus One phone, and now i have to repair this one
Click to expand...
Click to collapse
Well if you need a quality touch screen digitizer and LCD screen, we have them available at RepairsUniverse (dot) com.
Thanks but Ebay has better prices !

Samsung Epic 4G Screen Repair Take Apart Guide

This screen repair guide will allow you to safely and quickly repair damaged touch screen digitizer, LCD (AMOLED), and other internal parts of your Samsung Epic 4G. Disassemble your Epic 4G and get your Samsung smartphone working like new again!
This guide will help you to install the following Samsung Epic 4G part(s):
Samsung Epic 4G LCD & Touch Screen Glass Digitizer Assembly
Tools Required:
Safe Open Pry Tool
Small Phillips Screwdriver
T5 Torx Screwdriver
Samsung Epic 4G Take Apart Guide:
Remove the back battery cover by pressing in the button at the bottom of the phone, which will then loosen the cover. Then, you can remove the battery.
Now remove the back housing by removing six (6) screws that are holding it in place. There is one located at each corner and one on the center of each side.
Using the safe open pry tool, carefully insert the open pry tool in the crack between the back housing and the front housing of the phone. Start at the bottom, and gently loosen, working your way all the way around the phone. Then remove the back housing by pulling it gently away from the front part of the phone.
Next, use the open pry tool to unlock the keyboard and antenna clips. These are located at the left side of the motherboard, and appear as flat pieces of metal. Using the open pry tool, carefully insert it beneath them and press upward, to bend them into a straight up position instead of flat with the board as they currently are.
Figure 1
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then you will disconnect the antenna wire, which appears as a small white wire on the right side of the battery location (shown in figure 1). Using nippers, gently pull up on the top and bottom parts of this wire to disconnect it from the phone. Do not fully remove it, simply disconnect it and leave it as it is.
Remove the loud speaker from the bottom of the phone by removing one small screw on the bottom left that holds the loud speaker in place.
At this point, everything should be disconnected so that you can gently remove the entire motherboard from the phone’s housing.
Remove the keyboard frame by removing four screws from the center of the phone. Two of these are located in the black plastic beneath where the motherboard was located. Then, removing the sticker beneath the battery housing (as shown in figure 2) with the safe open pry tool to reveal two more screws that need to be removed. Then, gently pull up on the keyboard frame and it should come off without difficulty.
Figure 2
Now you will remove the C side housing by removing four screws located in a row, beneath the flex cable that is still hanging in place. Then you can remove the C side housing, but be careful not to damage the flex cable as it maneuvers through the hole.
Remove the slide rail by removing four screws, one at each corner. Two of these screws have rubber round covers that will need to be removed with nippers and placed aside. Use the open safe pry tool to pry apart at the top and bottom of the phone. Then move to the sides, where there are six (6) total clips holding the slide rail in place-3 on each side. Using the open pry tool, careful pry apart the sides, being careful not to damage the flex cable. Try to have all sides pried apart before pulling off the slide rail.
Now remove the slide rail flex cable by using nippers to remove the small blue pieces of tape, as shown in figure 3.
Figure 3
The odd-shaped black cable beneath the tape is the slide rail flex cable. By removing the front camera flex cable gently (a beige small cable located behind the camera lens) with nippers, you will be able to pry up the last end of the slide rail flex cable, and gently remove it.
Now you're Samsung Epic 4G will be completely taken apart allowing you to install any replacement parts you have purchased. Keep all parts together in the order you took them apart, and simply reverse the order to put the phone back together.
This should be stickied lol, very good guide, I just hope I never have to use it .
Sent from my SPH-D700 using xda premium
+1 Sticky request
Sent from my MIUI V4 Epic 4G via Tapatalk 2 beta 4
Thanks guys!
Glad you found it useful!
Nice guide! Ive done multiple screen replacements on the Epic and other phones and will say that this is a good start. As i recall... dont you have a youtube video explaining this??
EDIT: hmmm i couldnt find it so i guess not lol sorry!
travmofosho said:
Nice guide! Ive done multiple screen replacements on the Epic and other phones and will say that this is a good start. As i recall... dont you have a youtube video explaining this??
EDIT: hmmm i couldnt find it so i guess not lol sorry!
Click to expand...
Click to collapse
Glad you liked it!
We didn't do a video for the Epic however we did do a video for a couple of other Samsung phones which were very similar models and process for the screen replacement.
A few months ago the local Sprint store replaced the screen on my phone. Now the screen is loose on one side and doesn't quite sit square. Not sure if something loosened up or is bent or what, but this guide will be useful as I take the phone apart and try to tighten up the slider.
Thanks.
Nice. minor point...
repairsuniverse said:
Tools Required:
Safe Open Pry Tool
Small Phillips Screwdriver
T5 Trox Screwdriver
Click to expand...
Click to collapse
It is spelled Torx.
LargePrime said:
Nice. minor point...It is spelled Torx.
[/LIST]
Click to expand...
Click to collapse
Typo fixed.
I've taken apart several Epics, not using this guide although I wish I would have lol, so I know that there are some very detailed steps involved. Thank you very much for creating this thread and taking the time to write up a how-to! I am a strong advocate of doing-it-yourself so this kind of thing makes me glad that there are others who refuse to pay exorbitant amounts of money for repairs that could be done on your own, for much cheaper.
Sent from my SPH-D700 using xda premium
2 errors in this guide, just trying to help out from a Sprint tech standpoint.
A T5 screwdriver is not needed. All the screws in the SPHD700 are Phillips.
Removing the speaker is unnecessary. Sure if you need to replace the speaker, but removing the plate that houses the keyboard components does not require the speaker to be removed. It's best practice not to unless necessary, simply because the speaker has a cable component underneath that snaps into a corresponding cable on the keyboard; failure to ensure it sits properly will of course prevent your speaker and vibrator from working.
Heretofore, removing the bottom end of the white antenna wire from the speaker is also unnecessary.
Sent from my SPH-D710 using xda premium
Just wondering - where is everyone ordering replacement parts from?
Perhaps when this info is answered it could be added to the OP so that all the info is in one nice easy to find area
altimuh said:
Just wondering - where is everyone ordering replacement parts from?
Perhaps when this info is answered it could be added to the OP so that all the info is in one nice easy to find area
Click to expand...
Click to collapse
Samsung Epic replacement parts can be found here - Samsung Epic Replacement Parts
Hope this helps.
Great guide
Thanks for such a great write up.
blamethenetwork said:
Thanks for such a great write up.
Click to expand...
Click to collapse
No problem.
Glad you found it useful.
When my phone is in landscape mode the swype doesnt work when im swyping say the word android where i have to slide left and right. I dont know what the internals of the epic4g is made up of but im guessing theres a digitizer or sensor part under the outer screen. Could it be the problem or is there some app for calibrating the touch screen where im having trouble getting the word to complete through long left and right swype movements? I used the dev tools to test the areas i touch and it appears fine but not very accurate but doesnt seem like im having bad areas on the touchscreen.
Sent from my SPH-D700 using XDA
Does anyone have any experience replacing just the glass without replacing the LCD and digitizer? I cracked my glass and eBay has the part for very cheap, but sprint wants $100 deductaple to replace the phone. I'm wondering if the LCD and glass are bonded together.
zman0900 said:
Does anyone have any experience replacing just the glass without replacing the LCD and digitizer? I cracked my glass and eBay has the part for very cheap, but sprint wants $100 deductaple to replace the phone. I'm wondering if the LCD and glass are bonded together.
Click to expand...
Click to collapse
From what I've heard is the digitizer is so close to the screen or glass its really impossible to do it with out error... you'd have to get the whole deal and replace it.
Also might want to drop TEP as it requires a deductible and get a third party protection plan...
Sent from my SPH-D700 using xda premium
ÜBER™ said:
From what I've heard is the digitizer is so close to the screen or glass its really impossible to do it with out error... you'd have to get the whole deal and replace it.
Also might want to drop TEP as it requires a deductible and get a third party protection plan...
Sent from my SPH-D700 using xda premium
Click to expand...
Click to collapse
Went ahead and payed the $100. The cable that connects the two haves of the slider was sticking out of the case, so I took the phone apart to try plugging it back in hoping I could at least make the cracked screen light up. Turns out the cable was broken too, so I figured it would be cheaper to just get the replacement. Thanks for that 3rd party plan idea. I'll have to look into that for my next phone.
cm9eq
zman0900 said:
Went ahead and payed the $100. The cable that connects the two haves of the slider was sticking out of the case, so I took the phone apart to try plugging it back in hoping I could at least make the cracked screen light up. Turns out the cable was broken too, so I figured it would be cheaper to just get the replacement. Thanks for that 3rd party plan idea. I'll have to look into that for my next phone.
Click to expand...
Click to collapse
Yeah I'm buying my gnex from wirefly and they offer a premium protection plan for 7.50 a month and it covers everything... theft, damage, etc. With NO deductible. not bad...
Sent from my SPH-D700 using xda premium

Samsung P1000 Galaxy Tab Screen Take Apart Repair Guide

Does your outer touchscreen for Galaxy Tab has been damaged or cracked? This take apart repair guide shows you how to disassemble the Samsung P1000 Galaxy Tab cell phone quickly and safely. This guide can assist with the installation of replacement parts.
This guide will help you to install the following Samsung P1000 Galaxy Tab part:
Samsung P1000 Galaxy Tab Touch Screen Digitizer Replacement
Tools Required:
Safe Open Pry Tool
Tri Wings Screwdriver
Small Philips Screwdriver
Adhesive Stips (For Touch Screen Digitizer Replacements)
Samsung P1000 Galaxy Tab Take apart guide:
There are two screws at the bottom of the unit, and under two small plastic discs, use your small blade to remove this. With the discs remove you can use your tri wings screw drivers to remove the two screws as shown in Figure 1.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Figure 1​
Using your case opener tool begin to pry the back case of the unit be careful the buttons on the sides start from the bottom and work your way around.
With the back case remove, you can now remove the battery, the battery is held to the motherboard with the single screw and the connector, use your Philip screw driver to remove the screw and your case opener tool to pry the connector free, and gently pull the battery from the unit.
There are seven screws that you'll need to remove from the motherboard as shown in Figure 2. You can now remove the six ribbon connectors on the motherboard. These connectors for the back facing camera. After removing the connector gently pull up and the camera will come up as well.
Figure 2​
These connectors for the back facing camera. After removing the connector gently pull up and the camera will come out as well. With the screws and connectors remove, you can now lift the motherboard from the unit.
Carefully remove the ribbon cable for the LCD from the connector on the back of the screen assembly. Use your case opener tool to pull out the plastic tab.
You can now apply heat to the outside edges (front of device). We suggest using a heat gun or hair dryer. 30 seconds to a minute is all you will need to loosen the adhesive. Immediately use a safe open pry tool on the outside edges of the screen and the housing. Re-heat if necessary.
Remove the housing from the screen assembly. You can now use a safe open pry tool to release the touch screen from the LCD screen. Apply heat if needed.
Your Samsung Galaxy Tab P1000 is now disassembled and the appropriate parts can be replaced.
To reassemble, follow this guide in reverse.
Simply reverse the order to put the phone back together.
Thanks, useful. Been looking for something like this. Using guitar pick...
Sent from my GT-P6800 using Tapatalk
fluffmonster said:
Thanks, useful. Been looking for something like this. Using guitar pick...
Sent from my GT-P6800 using Tapatalk
Click to expand...
Click to collapse
Thanks. Glad it helped!!
What kind of adhesive is used to re-attach the digitizer
I just stuck a cheap 1 $ Screen guard on my tab... as it was bigger in size than my tab... i had to use a cutter to cut it and so i inserted the cutter in between the panel and the glass digitizer in all the four sides for cutting the extra part of screen guard.... and today after a week i saw the digitizer coming off the tab.... pls help me wat to do... the four corners of he digzer and the inside panel are still a bit sticky....
What kind of adhesive is used to re-attach the digitizer. Or maybe the soft gasket around the display melts and becomes the adhesive under heat?
Hi
Repaired two of mine and on went perfectly but the other has mess with green but if I push down on the tab screen then it is perfect.
Been debating weather to take apart again and resit everything. Also noticed on LCD itself there is a like loose liquid pattern ( if you know what I mean) nor to sure if they are connected.
Regards
Here is the pic
if you can see the green pattern
now here is when I push the screen in slightly
Just wondering before I go and take apart again is there any point or is there anything you can advise?
Sent from my LT26i using XDA
saheb_mnm said:
I just stuck a cheap 1 $ Screen guard on my tab... as it was bigger in size than my tab... i had to use a cutter to cut it and so i inserted the cutter in between the panel and the glass digitizer in all the four sides for cutting the extra part of screen guard.... and today after a week i saw the digitizer coming off the tab.... pls help me wat to do... the four corners of he digzer and the inside panel are still a bit sticky....
What kind of adhesive is used to re-attach the digitizer. Or maybe the soft gasket around the display melts and becomes the adhesive under heat?
Click to expand...
Click to collapse
We recommend the adhesive strips here to create a secure bond. These are the correct thickness strips for the touch screen. Digitizer adhesive strips
fluffmonster said:
Thanks, useful. Been looking for something like this. Using guitar pick...
Sent from my GT-P6800 using Tapatalk
Click to expand...
Click to collapse
That's pretty clever, really. Not sure why I haven't thought of using a guitar pick rather than stocking up on "Special Service Tools."
do u deliver in india????
repairsuniverse said:
We recommend the adhesive strips here to create a secure bond. These are the correct thickness strips for the touch screen. Digitizer adhesive strips
Click to expand...
Click to collapse
do u deliver in india????
---------- Post added at 12:37 PM ---------- Previous post was at 12:31 PM ----------
alexgogan said:
Hi
Repaired two of mine and on went perfectly but the other has mess with green but if I push down on the tab screen then it is perfect.
Been debating weather to take apart again and resit everything. Also noticed on LCD itself there is a like loose liquid pattern ( if you know what I mean) nor to sure if they are connected.
Regards
Here is the pic
if you can see the green pattern
now here is when I push the screen in slightly
Just wondering before I go and take apart again is there any point or is there anything you can advise?
Sent from my LT26i using XDA
Click to expand...
Click to collapse
I Just want to know wat glue u used to stick the screen back....
how did u stick the Touch Digitizer...???
I got 3M 2mm double sided tape for this, Repair Universe screen I think comes with the tape on it, and if it doesn't its about $4
alexgogan said:
I got 3M 2mm double sided tape for this, Repair Universe screen I think comes with the tape on it, and if it doesn't its about $4
Click to expand...
Click to collapse
thank You ... i am just wondering where can I get it.....
Deliver to India?
saheb_mnm said:
do u deliver in india????
Sorry we do not ship to India.
Click to expand...
Click to collapse
Hey what keyboard dock are you using?
It's one I sourced from China could not get what I wanted so am bringing in a few of them to sell on my site when it's launched later this month, have seen a few on eBay though but were not as good.
Regards
Sent from my LT26i using XDA
Sorry it took so long but we do ship to India now. Chat with us on our site for immediate assistance.
saz542 said:
thank You ... i am just wondering where can I get it.....
Click to expand...
Click to collapse
We carry the adhesive strips on our site. A link to the site can be found in our signature below.

Nexus 7 (2013) Take Apart Repair Guide

Is the screen on your Google Nexus 7 (2nd Generation) cracked or broken? You can repair the screen or other internal parts and components with this in depth repair guide. The guide will take you through each crucial step that will be essential in effectively performing a successful and safe opening of your device and repair nearly any desired part.
This guide will aid your installation of the following Google Nexus 7 (2nd Generation) parts:
Google Nexus 7 (2nd Generation) Touch Screen Digitizer Replacement
Google Nexus 7 (2nd Generation) LCD Screen Replacement
Google Nexus 7 (2nd Generation) LCD + Touch Screen Digitizer Replacement
Essential Tools:
Safe Pry Opening Tool
Small Phillips Screwdriver (#00)
Heat Gun/Hair Dryer
Google Nexus 7 (2nd Generation) Tear Down Guide:​
In order to get started with the repair you will first need to completely power down your device.
After the device is powered down you can start separating the unit's back cover from the screen assembly and also the motherboard.
Due to the fact the two are sealed together very firmly on this model, it may be very advantageous to begin with a small knife to release the first clips.
Normally if you start on the side of the device you will find it to be the easiest route. Next step use your pry tool to wedge between the seams around the sides and corners of the device until the back cover detaches from the tablet. Also be sure not to pry near the USB port located on the base.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After you have removed the back cover from the tablet, simply use your pry tool to release the battery connector which is found on the top right side of your device. This is done to be certain that the device is totally powered down.
Next you will use a Small Phillips screwdriver to unscrew the four (4) Small Phillips screws which are depicted in red in the figure below.
Also depicted below in the figure are the remaining flex cable connections which are colored green. Use your pry tool to release the flex cable connections. It is important to use caution and remove the connections while avoiding tearing any of the cables.
Once the flex cables are released, you will be able to carefully take out the battery and the housing it is located in.
Now that the cables have been released you will be able to detach the five (5) connections colored in green below using your pry tool, as well as extract all the screws (seventeen of them) from both the top and bottom motherboard components using your Small Phillips screwdriver.
Something to be aware of is the fact that the Small Phillips screws are unequal in size so it will be very important to keep them separated to ensure that the screws are later placed in the correct spots.
After you have removed the screws, you will then use your pry tool to take out the bottom motherboard component (Figure 3.1 ), along with the loud speaker underneath the motherboard (Figure 3.2).
You will find another connector under the loud speaker and using the pry tool can release it. Holding this part down is adhesive tape which needs to be cautiously removed (Figure 3.3) and this will make it possible to pull out the long orange flex cable.
Then using your pry tool carefully take out the top motherboard component. It is important to be certain all connections have been released from this piece to ensure that none of the flex cables release while you remove the motherboard.
Following the removal of the top motherboard component, you will then be able to remove the top speaker underneath it, which is displayed in Figure 3.5.
The last part you will need to extract from the housing is the button flex cable found on the left side. Using your pry tool, lightly press against this cable in order to release the cable that is bound to the housing with adhesive (Figure 3.6). After this piece is removed it will be possible to begin taking the glass touch screen off of the the housing.
Prior to taking off the screen, you will need to use a heat gun (on low) or a hair dryer to heat up the sides and corners of the device for approximately 40 seconds to 1 minute, this will make sure the tablet is not excessively heated. Once the device is heated up the adhesive that holds the screen together will noticeably loosen.
Next, after the sides and corners have been heated up, use your pry tool to shim in between the housing and the screen assembly, and be sure to run the tool around the sides of the entire device.
Finally, substitute in the new parts while discarding damaged parts and simply reverse these steps in order to reassemble your device back together.
RepairsUniverse's Repair Guides are for informational and learning purposes only. Perform this repair at your own risk.
Cool guide! This will be useful not only for general repairs, but also for those of us who want to do hard-mods.
Now I just have to buy one. The end of the month can't come fast enough...
Taking the back cover off looks to be a pain and almost impossible without doing damage. They are very well built.
Sent from my Nexus 7 using xda premium
This guide is excellent.
Well, it happened. Screen broke just by setting it down face-up on the pavement. These devices are incredibly fragile.
Is there any retailer that currently sells the replacement glass/digitizer? I am not thrilled to pay more than I paid for the device to have it repaired ($208!)
kgraves22 said:
Well, it happened. Screen broke just by setting it down face-up on the pavement. These devices are incredibly fragile.
Is there any retailer that currently sells the replacement glass/digitizer? I am not thrilled to pay more than I paid for the device to have it repaired ($208!)
Click to expand...
Click to collapse
We're expecting to receive parts for this device. Check back with us soon.
Orange cable
Hey this is sweet! In figure 3.3 I am curious to know what that flex cable is for. Thanks.
repairsuniverse said:
We're expecting to receive parts for this device. Check back with us soon.
Click to expand...
Click to collapse
Awesome. Is there any possibility you can give me a rough estimate for the part and for full repair? I am subscribing to this thread so I will be looking for your reply when the parts become available. Thank you very much.
By the way, if you ever need information on parts, flashing, or programming for Cricket Communications, I am your man!
Thank you so very much, I've had this device for 10 days and I'm pretty much devastated.
kgraves22 said:
Awesome. Is there any possibility you can give me a rough estimate for the part and for full repair? I am subscribing to this thread so I will be looking for your reply when the parts become available. Thank you very much.
By the way, if you ever need information on parts, flashing, or programming for Cricket Communications, I am your man!
Thank you so very much, I've had this device for 10 days and I'm pretty much devastated.
Click to expand...
Click to collapse
I'll have a better idea when we get the parts in. I'll try and keep you updated or you can visit my website from the link in my signature.
repairsuniverse said:
I'll have a better idea when we get the parts in. I'll try and keep you updated or you can visit my website from the link in my signature.
Click to expand...
Click to collapse
Did you ever get parts? I need to order a new screen and digitizer for 2nd gen nexus 7.
Thanks
combres said:
Did you ever get parts? I need to order a new screen and digitizer for 2nd gen nexus 7.
Thanks
Click to expand...
Click to collapse
We're still waiting... We have had alot of customers asking the same question.
Does the back cover feel more loose if you snap it back on after taking it off? Or is it still solid?
I need a digitizer only not sure how difficult that is to fix though....
That screen + lcd replacement cost more than what the actual N7 cost at any store. wow
gypsy214 said:
That screen + lcd replacement cost more than what the actual N7 cost at any store. wow
Click to expand...
Click to collapse
Yeah that price is horrible
keilflex said:
Yeah that price is horrible
Click to expand...
Click to collapse
I found this place called xcubicle that replaces the screen and lcd undearneath for 189.00 better price than going to pay 350 for a new one.Also go on etradersupply they sell the screen for cheaper
How adventagious is it to put a tiny plate of copper on where the CPU is? Im not sure how much room there is but my CPU tends to get in the 70c range when browsing at 1.9ghz. I feel like there's be reason to add a chunk of copper to attempt to reduce temps for a little bit before it starts to throttle...
Same here!
kgraves22 said:
Well, it happened. Screen broke just by setting it down face-up on the pavement. These devices are incredibly fragile.
Is there any retailer that currently sells the replacement glass/digitizer? I am not thrilled to pay more than I paid for the device to have it repaired ($208!)
Click to expand...
Click to collapse
Did you find any seller? I also got my nexus's screen cracked and looked for replacement some site even said 600$ come on who is going to pay that much for screen ... the cheapest i got was 208 $ so even that is high for a device this cheap... so if you or anyone got some idea where and how to get replacement glass/digitizer that will be great help. (LCD is just working fine so why to buy lcd but all of them include lcd which i think makes it expensive. )
Buy a new tablet.
Keep the broken one for a year, spare part will be cheaper.
sk8trix said:
I need a digitizer only not sure how difficult that is to fix though....
Click to expand...
Click to collapse
You can go to our site and find the piece your looking for as well as get a free pry tool for the job. We also have a tutorial video you can follow to help you in fixing your phone and have "live chat" support so you can easily get help if needed. But on newer phones we don't recommend getting just the digitizer as it can be a little more difficult to separate from the LCD, and to prevent further issues or complications, it may be worth your time and money to get the combination LCD and Digitizer.

Categories

Resources