Related
I have couple of scratches on my touch pro screen.when the device is on the scratches are like rainbow colors really visible.If I change the touch screen (not the whole lcd screen) that will fix my problem right? Did any1 do this?
ummm i think when u meant by "rainbow colors" then ure gonna have to replace the WHOLE LCD screen, cuz more than likely its from the LCD screen, and i dont think the touch screen and LCD screen are 2 parts...i think theyre just one...not sure, but try to look on ebay OR idk if u have warranty on it u can probably call in HTC about it...
This is what I think will fix the scratches
Code:
[CODE]http://mobile1.brando.com.hk/prod_detail.php?prod_id=03976&dept_id=088&cat_id=0695
Code:
Much cheaper
For Digitizer Module for T-Mobile MDA Vario IV Touch Diamond
http://www.dealextreme.com/details.dx/sku.20648
For HTC Diamond
http://www.dealextreme.com/details.dx/sku.20647
I don't know if it fit the same as Touch Pro or Fuze, but read the spec
I have difficult time finding a How to replace digitizer video.
Any help?
Thanks
radoste said:
I have difficult time finding a How to replace digitizer video.
Any help?
Thanks
Click to expand...
Click to collapse
Maybe this can help.Its a How to remove cameras from touch pro with pictures
Code:
http://www.mediafire.com/file/h2mmwetxnij/HTC%20Touch%20Pro%20-%20Camera%20removal%20photo%20guide%20v1.1%20by%20A%20Mak.pdf
I saw that. It does not show how to remove the screen.
Why would you want to remove the camera?
radoste said:
I saw that. It does not show how to remove the screen.
Why would you want to remove the camera?
Click to expand...
Click to collapse
I wouldnt, thats just the only touch pro take apart that I found with pictures
mikechannon.net is a good place to start. But if you are looking to replace the digitizer only, you won't find it there. It's a bad move anyway. I tried that, cracked my lcd and end-up buying the whole lcd like this.
All I can tell you are my mistakes.... lol....
- never peel of the digitizer. it will ruin it.
- never try to remove the lcd with cutter blade. this is how i cracked it (stupid me and still regret it)
- between the lcd and the digitizer there is a thick, clear double tape like glue. i came across some information about this somewhere (forget where...). one said you should heat the glue first (don't know how to apply this without affecting the lcd) . other one said have to use dental floss.
So, there you go.
HTC Touch Pro- LCD & Digitizer replacement instuctions
Hi everyone. I have SCOURGED the internet looking for some kind of decent instructions to replace the LCD & Digitizer screen on my HTC Touch Pro (Sprint) phone with the new set I purchased from Hong Kong. Mike Shannon's site does NOT give directions for this specific area.
I have seen you all talking about needing to do the same thing and wonder if anyone has done it? And do you have any directions to help me?
I've had this part for a month now, and can't find any directions to do it! My dog chewed it, and the touch works, but the screen is half black now. I read it is easier/less risky to replace both lcd and digitizer, which I went ahead and purchased them both with the tools, now I just need to find something decent (instructions) to have help replacing it.
thanks to anyone who can step up to help me, I'm frustrated beyond all comprehension, and now feel I may as well ditch the phone if I can't find a way to replace it. Or maybe you know someone I could send it off to? Everyone wants to charge a couple hundred bucks sending it in to them!
to the appling heat ...u can try putting it in a ziploc bag and boiling it ...and for the instructions this is the best i can do for u http://store.payloadz.com/str-asp-i...nance_Manual_eBooks_Technical-end-detail.html
im pretty sure after all ur fustration 8 dollars wont kill u ...and im pretty sure the condensation from the boiling wont hurt
and i found a free one hope it helps http://www.htcdriver.com/index.php?page=htc-raphael
it's a long trip, in russian, to get to the lcd
http://www.pdacenter.ru/razborka/htc-touch-pro/
You can use Google translate on it. It seems that the hardest component to get to is the lcd. I also bought the digitizer, since my lcd is fine. I'll post a follow-up if I go for it.
Any luck getting the touch screen off and new one on?
I bought a touch screen and digitizer as separate items. I wish I had known that some kind of clear adhesive is supposed to be between them.
A) What happens if you don't use this adhesive?
B) Has anyone successfully replaced the screen/digitizer with replacements on the fuze or touch pro?
Anyone having luck?
Has anyone actually figured out how to install this? I just got what was supposed to be a replacement LCD+digitizer. they shipped the pieces seperate, so I can't understand how to put them together, since HTC seems to only list the part as one piece and there are no instructions or videos anywhere that indicate how to install them as seperate pieces, or get them to connect.
Dont do it!!
Ok, I just recently bought a parts phone on here (a Fuze) and was "just going to replace the digitizer" (Authors laughs, then cries at statement)
Ok, yes you can replace the digitizer without replacing the screen, BUT they tell you to use an oven (you can buy one from HTC they make it available to their techs, so you need someone that can get that for you). If you do not make sure that ALL of the glue is loose prior to taking the digitizer off you will split the LCD.
It is much simpler to get either a parts phone or a screen and digitizer and replace the part. I had to replace my digitizer as the touch function did not work. You can find older project phones in the market section. If you figure the cost of a parts phone (plus you have extra parts if anything else goes out) vs. if you buy a digitizer, then rip a part of the LCD because all of the glue was not disolved, and have to buy either a parts phone or a new phone anyway you will be way ahead of the game.
There are a number of good resources on here as to how to disassemble and reassemble the fuze.
I WOULD NOT RECOMMEND TRYING TO REPLACE THE DIGITIZER ALONE IF YOU HAVE NOT BEEN TRAINED OR HAVE THE PROPER EQUIPMENT - unless you need a reason to sell your spouse on why you need a new phone. "Honey, I tried my hardest to fix it, but I guess it is really broke now, I'm gonna have to get an HD2"
If you have any questions about the process let me know I am always more than happy to help.
http://www.mikechannon.net/PDF%20Manuals/HTC%20Raphael_SM_A10%20_GENERIC__01%20Dec%20
pkwhisker said:
Mike Shannon's site does NOT give directions for this specific area.
Click to expand...
Click to collapse
Yes, indeed, mike channon does offer a very detailed service manual for the raphael.
Replacing the display on the HTC Touch Pro (Raphael): Some Tips
Replacing the display on the HTC Touch Pro
How To - Tips
1. Collect information
a. Find the Service Manual HTC Touch Pro (Raphael) on Mike Channons's site, the Raphael wiki or you could Google for it. File name is "HTC Raphael_SM_A10 _GENERIC__01 Dec 08.pdf".
Take a look at the disassembly and assembly chapters of the Service Manual.
The following two lists may be helpful.
---
List 1: types and quantities of screws
[SPL no., P/N, pages of Service Manual, description, quantity used in Raphael]
10. 72H01893-00M (see p. 34), black (middle length), 2x
11. 72H02450-00M (see p. 32, 34, 30), black (shortest type), 7x
12. 72H02474-00M (p. 37), black (longest type), 4x
13. 72H02689-00M (p. 30), metal, 4x
26. 72H02865-00M (p. 35), metal, 6x
27. 72H02886-00M (p. 35), 1x torque screw for M/B, 1x
---
List 2: kinds of tape/fabric used in the Raphael
a. Conductive fabric
Self adhesive conductive fabric, parts 14-24 on the SPL. The adhesive backside is also conductive.
b. Mylar
A specific kind of polyethylenetereftalaat (PET) used for electical insulation.
c. Kapton tape
Kapton is a polyimide film which can remain stable in a wide range of temperatures. (electrical insulation)
d. EMI gasket
EMI shields are implemented in a design to isolate one component or section of a device from another.
e. Double sided tape
---
b. Movies of the disassembly process can be found on YouTube for the HTC Diamond.
The Diamond does not have an integrated keyboard, so it is a bit different, but it is good enough to get an idea of the process.
The information on how to replace the screen itself is not found in the service manual.
c. Study the last few stages of the HTC Touch Pro page on pdacenter.ru
(Translate the page into English using Google.)
The display is attached to the metal frame by 4 small pieces of double sided tape.
3. Get some tools
a. Phillips (cross head) screwdriver size 00x50
The right size is 00. The length, 50mm, is less important.
There is one torque screw in the Raphael (SPL no. 27), but it can easily be handled by a normal screwdriver.
b. Plastic stick (to open the case)
The standard plastic stick I had ordered was actually too big. The one I made myself was smaller and proved to be better.
c. Other tools
I did not use these, but if you plan to do more than one it would be a good idea to use the
- plastic tweezers
- ESD wrist wrap
- rubber gloves
4. Buy a display with touch screen attached to it
You could buy the touch screen and the display separately, but I could not find any information on putting them together. Avoid problems by buying these already attached.
5. Replace the display
a. Disassemble following the Service Manual, leaving the M/B unit in order.
Be careful not to break the small speaker cords. Do not move them too much because they are very fragile.
Be sure to keep every piece of tape safe for reassembly. Buying new tape can be quite expensive.
b. For the last stages, follow the instructions from pdacenter.ru.
Press the old display gently out of the metal frame. Move the pieces of double sided tape from the old to the new display, and fit the new one into the metal frame.
c. Reassemble following the Service Manual.
Good luck!
What will fit what?
Will the lcd and digitizer from a sprint version work on an alltel version(ppc-6850)? Or is there another lcd and digitizer that i can use? Im back to the old berry 8703 and its killing me.
spammer said:
if you just find scratches on the surface, then you just need to change the touch screen digitizer. the soldering is requested when you fit it.
But of course, if you buy the one that lcd and touch screen fit together one, then no soldering request.
Anyway, soldering is not such difficult if you has the tool.
thanks
Click to expand...
Click to collapse
I don't see any soldering involved there. The digitizer is fitted with thin lines of some kind of glue or kit around the edges. I have not seen any documentation on it though.
ingmardb said:
I don't see any soldering involved there. The digitizer is fitted with thin lines of some kind of glue or kit around the edges. I have not seen any documentation on it though.
Click to expand...
Click to collapse
you can look at the connect flex cable part of your touch screen and the lcd, you will find they are soldered together. Of course , if you don't soldering it together, it will also work, but not as good as after soldering.
I dropped my phone and need to replace the housing. It looks like the digitiser cannot be easily removed from the housing, so I bought one of these as well. Now all I have to do is move the phone from the old housing to the new and install the digitiser in the new housing.
Now it looks like the digitiser may have been glued in place. What type of glue should I use ?
::Pixel.Freak:: said:
I dropped my phone and need to replace the housing. It looks like the digitiser cannot be easily removed from the housing, so I bought one of these as well. Now all I have to do is move the phone from the old housing to the new and install the digitiser in the new housing.
Now it looks like the digitiser may have been glued in place. What type of glue should I use ?
Click to expand...
Click to collapse
More liked taped in...... I'm sure that lots of people will respond with.. Double sided 3M tape.... but if there's anything better/stronger than that on the market use it. Make sure it''s really thin tape to. I'm gonna be replacing my housing in the next month or so aswell. Goodluck.
As I also will replace mine digitizer, the newton rings are bugging me, it will be appreciable if you can share your experiences of the replacement process.
thanks in advance and god luck
Hey on more thing. I took apart my phone last night and put it back just so I know my way around when parts come in.
If your Digitizer does not work try loosening the top srews 1/4 turn. You have them on too tight.
I wasn't replacing mine so I didn't have to remove the existing one. All I had to do was attach a new digitiser to a new housing.
I was told that double sided tape was the best, so I tried that.
I used the instruction from http://www.pdacenter.ru/razborka/htc-touch-diamond2 which was easy enough.
You need to ensure you remove the micro SD card first.
Also I forgot to move the LED diffuser from the top, so I need to repeat the process at some stage.
The housing I bought had a number of issues
* The two screw point near the bottom of the housing didn't have the metal inserts with the screw threads
* There was no seal between the metal housing and the LCD screen. This could let dust in.
That's about it for a brain dump.
Hi there,
I was also tired from that oil stai and ordered a new digitizer from these guys:
http://xxx.sw-box.com/htc-touch-diamond-2-t5353-digitizer-touch-panel-screen.html
Surely it arrived in 6 days, to my horror it was a generic display,
Had some trouble removing the old one, ended up breaking it
The generic did not fit snugly, I had to sand down the edges to make them round, also had some trouble with the four buttons below getting stuck when pressing down, (shaved of some extra plastic). anyway used double sided scotch film to get the digitizer back in place.
apart from a few difficulties, it works like a charm.
Should have ordered an OEM but what's done is done
Next time I'll do the cover and get a new digitizer
Regards
I would of thought double sided tape too thick to use to stick the digitizer on.
I was thinking of using a very thin sliver of clear silicone.
Anybody tried this or have any other suggestions?
Thanks
I used a very thin layer of supergleu and it worked great!!
My digitizer came pre-glued. I didn't need any sort of glue.
http://forum.xda-developers.com/showthread.php?t=715724
Silicone is OK
I used a very thin layer of black silicone and placed a book on top of the digitizer to keep it pressed flat into the case as it dried overnight. No problems since then...
The missing metal screw inserts can simply be pulled out of the old housing ; insert screw halfway and gently pull with plyers. Carefully hammer into the new casing; insert screw 3/4, put something thin and metal on top to prevent the screwhead from getting damaged and carefully hammer into the void. Make sure it goes in straight.
I've got exactly the same issue with my new housing, no bottom screw threads and no foam for the lcd to rest on. Am trying to pull the threads out with pliers but I think the old case is going to break first or strip the threads.
This is isn't an easy job
have finally finished this epic!!!!
had to break the bottom screw threads out of the old front housing and took a good while hammering them into the new housing so I didn't break it.
used a small sliver of clear silicone to glue the digitizer in which seems to work well so far.
Have not put any foam or anything for the LCD to rest on, time will tell what effect this has.
I need to change mine as well. Where can i buy a good quality digitizer and case preferably pre-glued?
I found a few on ebay but i am not sure of the quality.
Thanks
Today i searched also for shops which have digitizers and housings. I have found 2 shops, but one of them is a german shop (http://www.mobileok.de) which does not deliver outside of germany and austria. But the other one does: http://www.sw-box.com/
what kind of glue? it's the third time that i'm re-gluing it, but dust keeps coming inside....
I guess, it is not possible to hermetical seal the housing. I had dust in my original housing too. There are a lot of small gaps everywhere not only between digitizer and frame. But it would be easy to disassemble the device from time to time, remove the dust and reassemble it again. Save your energy in the effort to make your device dust proof.
Hello
Today my loved Touch HD fell down and the front glass of the touchscreen is broken now :/ Because the reparation is so expensive, I think about repairing it by myself. Now I just want to ask you: Is this the right part?
(Picture 1.PNG in the attachment)
Or do I have to take sth like on the 2.PNG?
Picture0017.jpg is a photo of the broken touchscreen.
And another question: Is it hard to do this by myself?
Thanks
Greetings,
IceFire32
PS: Sorry for my bad english :/
Hi i did this myself. It is a little fiddley. At the last stage removing the glass from carriage was worst bit. Had to apply a substantial amount of pressure. (see the metal distorted off the back of the sensor)
I only wanted to change the casing. Ended up breaking the glass and tearing the connecting ribbon on the sensor.
Since your replacing this part anyway the whole pocess is much easier.
I got the parts off ebay. Cost me £56 in feb.
there is a good tutorial linked in this forum somewhere. Do a search. Guy with a strong italian accent.
PS get some double sided tape. as thin as you can find it.
and be very careful how you place the glass back in or use a weak adhesive tape.
Watch the tutorial. (search the forum) to see where he pushed to dislodge glass.
Hope this helps.
Hey everyone my HTC HD2 got the Non-Responsive screen problem a week ago, & did a lot of research and found out that it was most likely a hardware problem with a cable..... So a lot of people would tell the people with the problem that the "Touch Screen Digitizer" is dead (like the cable), or it needs to be cleaned... pretty well go out and buy a new one... BUT I have never found evidence that someone has done this and it has successfully "cured" their HTC HD2 Non-Responsive touch screen problem...
So I was looking for anyone on the forums that could confirm this is a solution or give me any tips on what I should do.... AND no I don't have enough money to get a new phone, nor do I live in the USA so I can't send it in to fix it...
This is what I was going to buy for it:
http://www.ebay.ca/itm/NEW-OEM-HTC-...781?pt=LH_DefaultDomain_0&hash=item519a3d2e45
Thanks for taking the time to read my Thread, its much appreciated!! I hope I can find a fix!!
PS: If anyone wanted to know what it looks like out of curiosity I posted 3 pictures with RED circle HIGHLIGHTING the problem when I try to touch something....
My digitizer has been a bit dodgy for the past few months. It's ironic that when I finally found out what the issue was and called HTC, my factory warranty had ended exactly 4 days prior to the call.
Fast forward 3 months and my phone has now been unresponsive for 3 hours despite my prying and tweaking various hard parts.
I disassembled the phone down to the main board just to see how hard the install is, but it's a bit intimidating once it's time to start pulling all the film and ribbons. A bit too tight and small parts for my liking.
Time to hit CL to see if I can find a cheap replacement.
Good luck with your repairs. I may be following in your footsteps if I can not find a good deal.
Yeah I will see how well it goes... if anyone has useful info, i will be more than grad to hear it
Thanks
Many people attempt to replace a digitizer, but I simply don't recommend it, we see enough of do-it-yourselvers who created problems in addition to the original ones.
What I do recommend, however, and I stated it on many threads already, is to get an LCD+DIGITIZER assembly. Simply because it is easier to fit. Not saying the overall fitting is easy, always depends on your overall skill, so ensure that you are familiar with the procedure BEFORE you begin. But you will save yourself a lot of trouble by getting the whole thing, as opposed to the digitizer only for the sake of a few bucks.
However, if anyone still feels intimidated by the whole thing, I am on the lookout for working main board. Advertised a few times in the marketplace with limited success. So if anyone smashed their baby and will be looking to replace, rather than repair - drop me a PM. I am in NZ. Will pay by Paypal.
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
How much did the set cost?
cheeselump said:
Mm i've replaced my HD2 screen just last night. Trust me it's among the most complex phones around.
Unless you've done a few phones before i wouldn't advice you DIY. Otherwise you can look carefully at the Leo Ds. and Leo As. guides on youtube. those helped me!
Mm i killed my LCD in the process of removing the digitizer as it's stupidly glued on to each other and the LCD glass is thin as hell.
Get the set, it'll save you your time
Mm i got mine of ebay, from the seller goodgoodsecho. It works perfectly well for me!
All the best!
Click to expand...
Click to collapse
Thanks I will check it out, hopefully it won't be to hard and I hope I can repair it!! oh and could you post a link of the youtube & manual you used to replace your screen?? Thanks
Oh would anyone suggest then just calling HTC and sending it to them to repair?? or does that cost to much??
Thanks everyone for the help
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Heronization said:
Yah I was looking at the video's and they were taking off EVERYTHING... it looks really hard to do.. I don't know whether I want to do it anymore.....
oh and are you talking about the digitizer itself or the LCD+digitizer for your method?
Thanks
Click to expand...
Click to collapse
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
GnatGoSplat said:
Yep, there is absolutely no reason to take off everything like some people seem to think is necessary.
The way I'm talking about requires removing LCD+digitizer. In fact, I think you'll always have to remove both because the connector for the digitizer is under the LCD. Anyway, the way I did it, I went from removing the the phone insides from the rear housing straight to separating the LCD+digitizer assembly from the frame. No removal of any boards or flex cables. The only cable to be disconnected is the LCD+digitizer assembly one. Getting it disconnected and reconnected does require unplugging the front button flex and removing the screws for the bottom logic board to loosen it, but that's all.
Click to expand...
Click to collapse
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Heronization said:
Wow that sounds pretty simple! and for you it all works perfectly now?? no calibration needed or problems?? Maybe I will try it after all..... but what screw drivers to I need to dissemble it?? the screws look different from normal..
Click to expand...
Click to collapse
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
GnatGoSplat said:
Well, it's not that simple because simply getting the HD2 insides out of the rear housing is difficult if you've never done it before. I believe the screwdriver you need is a Torx T-5. Once you get the screws out, you will need a plastic opening tool to go between the digitizer and rear housing frame. They look like this:
http://www.ifixit.com/Tools/Plastic-Opening-Tools/IF145-000
I found it comes out much easier if I use the tool to make a gap along the top edge and then slide the entire end of a scrap credit card into that gap, then that makes the whole assembly easier to pry out along the sides with the tool. I know on one of the vids, the guy takes forever doing this part and I can understand why, but once I figured out sliding a credit card into the top gap as far as it would go, I was able to get it apart much easier.
I can't answer whether the phone will work properly, because I just ordered the new digitizer over the weekend and haven't put it back together. I did remove the LCD+digitizer assembly and then re-connected it and put it back, then powered on the phone just to make sure pulling the LCD didn't hurt it - it didn't, everything worked as well as it did before. I did manage to crack the digitizer more when I tried to get the insides out of the rear housing before I figured out the credit card trick, so fortunately I was not trying to save my digitizer as it was already cracked. If you are just wanting to try to clean or fiddle with the connection, then you're going to have to be a LOT more careful than I was because it was all too easy to crack the digitizer!
I'm guessing yours probably needs replacement though. I sent my HTC Surround in for a funny acting digitizer, and the digitizer was replaced.
Oh, and if I would have bought an LCD+digitizer pre-assembled unit, that would have been super easy to replace. However, I opted to save $50+ by buying just the digitizer. Not too sure how I'm going to prevent dust getting in it, and I've read thickness of the adhesive is critical. I may regret it later!
Click to expand...
Click to collapse
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Heronization said:
Ok thanks I think thats what I am going to do, first dissemble it then try to move the cable around because, just yesterday it started to work again and then today it isn't working. I will contact you if I have a problem or get stuck, if that is ok with you
Thanks a lot
Click to expand...
Click to collapse
Yeah, no prob. I can post a pic of the digitizer lifted from the frame which shows where the adhesive tapes are that you have to go through, if it would help.
GnatGoSplat said:
One word of advice I have, is just remove the LCD/digitizer module assembly and don't remove anything else.
I have no idea why these videos and manuals have you pulling circuit boards, flex cables, and disconnecting stuff just to remove the LCD module. All you really have to do after removing the rear housing is to cut through the double-sided tape holding the LCD module to the main frame, being careful to know where the flex is and not to go too deep there. I used a credit card for that, but anything similarly flat and thin should do.
Click to expand...
Click to collapse
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Heronization said:
Hey lolz I need your help already, I just took off the back housing and now Im lost on what to do... It looks to me as if you do have to remove the cables from the motherboard to get to it?? and what is the double sided tape? and isn't everything connected to the lcd?? lolz this is my first time doing any phone disassemble.. Thanks
added a picture of what I was thinking of doing... or am I doing this all wrong... because you did say we don't need to remove any flex cable or wires and stuff
Thanks!!
Click to expand...
Click to collapse
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
GnatGoSplat said:
Nope, I didn't disconnect anything except the circled connector on the far right of your picture. You will need to do that to remove the LCD flex cable from the logic board.
I've attached a pic of the LCD module loosened from the frame. What you do is use something thin and flat to separate the adhesive tape holding the LCD to the frame. You will need to lift some of that black fabric tape on the edge to see where the LCD module meets the frame. Near the top, you will probably have to slide your separating tool all the way through to separate the tape (I used a scrap credit card). Avoid the area where the LCD flex cable is, because you could damage it! It's on the lower right of the LCD if you are looking from the front. When the LCD is loose, lift up from left to right (when LCD is facing you), pretending that there is a hinge on the right side. This is because you don't want to put any force on the LCD flex.
Once you've got your phone looking like my picture, you can remove the "captain" (orange tape), unlatch the LCD flex from the top, remove the button flex from its connector, then loosen the bottom logic board from the frame just enough to pull the flex out of the connector.
I hope that makes sense! It probably helps to know that a very strong double-sided sticky tape is all that holds the LCD+digitizer assembly to the frame, and there is only one flex cable connecting LCD+digitizer assembly to the rest of the phone.
Click to expand...
Click to collapse
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Heronization said:
Awesome I will try it now, I do need to heat the screen some for the tape to get sticky so I can pry it off right?? and I am guessing once you have removed that tape you can't "just stick it back on together and it will work right?? right??
Click to expand...
Click to collapse
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
GnatGoSplat said:
You could try heating; I didn't, but maybe it will come apart easier if you do. In the HTC factory service video, they mentioned putting the whole phone into the oven to loosen the tape. I didn't know if it would be a good idea to do that complete with all the circuit boards or not.
No, without heat, the tape is definitely ruined and I will need to replace it. I was planning to use some leftover tape I have from fixing iPhone digitizers so I didn't even attempt to salvage the existing tape. Not sure if it's even possible to salvage that tape considering you need to stick some kind of tool in there to separate it.
Click to expand...
Click to collapse
Alright thanks I have to go and don't know when I'll be back, but I will try it tonight and hopefully I don't break anything...
Thanks for the help!
just found a very easy way to replace the whole display in just 3 minutes by accessing it from the front side..
i am not yet allowed to post the link, but if you google this
IMPEXTROM CAMBIAR TROCAR DISPLAY HTC HD2
you will see the 3 minutes video
seems possible as there are 19 positive and just one negative vote on this video..
(my display was broken, but have worked for a year or so.
now it is frozen/ unresponsive and i have purchased a full display.)
but it seems too easy to be true ...
any hints?
thanx &cheers
That been set up for the video as you can see it been off before & the chassis the lcd is bonded to is clean of all bonding tape :-/
Also original has signal interference tape runing down sides across all 3 layers.
also if you heat the front first thing to seperate is the digi from LCD as the lcd to mid chassis is a strong bond.
Best way is popping them out of rear cover, fitting a pre built lcd/digitizer is not hard, just use quality adhesive to hold lcd to centre chassis & buy pre cut black foam tape for the top & bottom digi glass edges or rebuild is next to pointless without this done well.
I've done a good 30 odd HD2 screen & mainboards & no way I could do it to my standard via that video.
Hi Mister B - thanks a lot for your advice, i believe you are right!
but as i have never attempted to disassemble a mobile phone, is there a video tutorial how to do that properly for an absolute beginner?
as I need my phone functioning tomorrow, i'm considering to try it in the morning.
light2 said:
Hi Mister B - thanks a lot for your advice, i believe you are right!
but as i have never attempted to disassemble a mobile phone, is there a video tutorial how to do that properly for an absolute beginner?
as I need my phone functioning tomorrow, i'm considering to try it in the morning.
Click to expand...
Click to collapse
Not sure if Mister B will reply in time, there is a good thread here http://forum.xda-developers.com/showthread.php?t=1566179 with a video in post 2 else google hd2 disassembly youtube perhaps
Hi Robbie P,
Thanks a lot for the link!
Now it seems I will have to postpone this operation for a day or so, until i learn:
1) What time I would need (seems about 2h for a beginner)
2) What money I would need - as I have to buy these tools- what would be a price... i guess 10-15 euros?
(BTW Finally I guess that people who published aforementioned 3.5-minutes tutorial did so not to help us, but to make us damage our smartphones, so their services would then earn more, repairing it?
As I see no other explanation...Now found another such a scam video -
just google " HTC HD2 repair, disassembly manual ")
Cheers
Have a good read of link put up by robbie p
I done a few posts in it that worth looking at as you don't need remove the flexboard & volume button & antenna cables which saves a lot of possible accidents & hassle.
Most important thing is extreme care, volume button is damaged easily if pry of back badly or with screwdriver. antenna tabs are snapped off mainboard with poor handling while separating the layers.
It easy to do but first one is never perfect unless you really pay attention.
You don't need much tools, a basic kit from ebay for about 4euros will cover you along with things you probably got already such as hairdryer & razorblades etc.
Just buy good padded tapes to fit top & bottom of digitizer & strong tape to bond lcd to centre chassis
links to some parts in the HD2 wiki >
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips
tools
Hi Mister B!
Thanks a lot for you precious advise.
Will try to do it myself, not in a hurry, as soon as I get 3 hours spare time - hoping it would be enough.
Then I will need to install some good Android instead of the original WM6.5- but that is for another topic
My Qs:
You don't need much tools, a basic kit from ebay for about 4euros will cover you
this is what I got with my display from Ebay: Is it enough?
1 pry tool ,1T5 screwdriver and 1 T6 screwdriver.
Just buy good padded tapes to fit top & bottom of digitizer
I also got this one from Ebay: is it good? if you paste the title below into ebay.co.uk it you will see more details:
2mm Double Sided Layer Adhesive Sticky Tape Sticker for Mobile Phone Glue LCD
& strong tape to bond lcd to centre chassis
Which width, and should it also be double-sided?
Cheers
For tape you want this >
http://www.ebay.co.uk/itm/LCDFIX-Fr...765?pt=LH_DefaultDomain_3&hash=item1e9ebb1595
I assume you have lcd & digitizer pre-built new !?
You would be better off with couple more decent pry tools, the green ones tend be better than the blue plastic stuff.
I use 2 pry tools on top of HD2 either side of speaker grill as makes back housing removal a few second job & leaves not one mark if done right.
Only other thing you may need is tweezers & cleaning buds for old glue.
top digitizer tape need be right or blocks sensor hole or looks shabby.
Don't force the old lcd off centre chassis as if gets bent then never fit back right, warming it up with hairdryer helps ease it off.
I always have a spare button board on hand too as makes it easy bench test the lcd/digitizer hook to mainboard side by side with battery held on mainboard pins & spare button board used to power on, also good as likely find old board breaks if gone brittle.
www.ebay.co.uk/itm/360542084387
tools I've got
Hi Mister B!
Thanks so much for your suggestions!
Yes, I've got the full display, and only the tools as on the photo.
My few Qs:
Only other thing you may need is tweezers & cleaning buds for old glue.
Could not find plastic tweezers, only metal ones... But those cotton sticks for ears i have
I could order the LCD tape, though it seems a long wait (7-10 days) for express delivery up here, so is there an alternative?
Thanks for a link to the button board! As I guess mine is damaged, for during last few months I had to press hard on the power button to get the phone responsive again. Then even this trick stopped working.
But also due to the longer waiting to get in from China - is there a way to test and learn if i need to replace it , before starting digging into my HD2?
Cheers
I would get the lcd digi top/bottom tape kit as what you got in big roll will be no good.
all else is good.
button board is handy as ribbons go brittle so can break plus you can use it to power up the device in a pre build test with lcd/digi & mainboard laid flat side by side & new ribbon plugged in to mainboard to power on. Most stuff makes it to uk pretty quickly, quicker order - quicker get it
Well, i will then order both items today, in hope it won't take too long to deliver up here (Belgrade, Serbia).
A video tutorial with all the tricks you have suggested would be the easiest way to follow, but it seems there's no such a video - yet.
Certainly, I'am either not sure whether will be able to film my own attempt.
Mister B - thanks so much! Following your suggestions, and the topic mentioned by Robbie P - I will likely manage to do the job properly!
Cheers
If have any question during rebuild post them here & I will respond as soon as see it.
Good luck ...
Thanks!