Related
Problem: ClockworkMod not booting from MicroSD card
What I'm trying to do: Dual-boot CyanogenMod 7 with the stock Nook Color with Cyanogen 7 on a MicroSD card, but without rooting the Nook Color.
What I've done so far:
1. Downloaded ClockworkMod 3.2.0.1 from download.clockworkmod.com/recoveries/recovery-clockwork-3.2.0.1-encore.img
2. Downloaded Win32DiskImager from launchpad.net/win32-image-writer/trunk/0.3/+download/win32diskimager-RELEASE-0.3-r27-binary.zip
3. Using Win32DiskImager, flashed ClockworkMod onto the MicroSD card.
4. Ejected MicroSD card.
5. Inserted MicroSD card into Nook Color (which is turned off)
6. Connected Nook Color to PC via USB cable
7. Powered on Nook Color
8. Watched as standard Nook Color boots. Nothing at all displays related to ClockworkMod.
Other troubleshooting thus far
a. I've gone back to step 3, used Windows 7 to just format the SD card to ensure it was blank, and then started with Step 3 again.
b. I've ensured the MicroSD card is set properly into the Nook Color.
c. I've tried holding down the power key on the Nook Color (no effect).
d. Searched these forums via its Search function, and searched via Google (most references use ClockworkMod 3.0.2.8, which a few posts mention does not work on the "blue dot" version of Nook Color.
Misc:
MicroSD card: SanDisk Type-2 4GB
Nook Color (the "blue-dot" version that starts with a 1GB partition for side-loading)
PC: Windows 7 64-bit, built-in SD card reader/writer
Any help or guidance would be greatly appreciated. Thank you.
Ynglaur said:
Problem: ClockworkMod not booting from MicroSD card
What I'm trying to do: Dual-boot CyanogenMod 7 with the stock Nook Color with Cyanogen 7 on a MicroSD card, but without rooting the Nook Color.
--- SNIP ---
Any help or guidance would be greatly appreciated. Thank you.
Click to expand...
Click to collapse
If all you're trying to do is setup a bootable SD card with CM7 on it, and retain the ability to also boot to the stock Nook ROM, try this:
http://forum.xda-developers.com/showthread.php?t=1000957
Based on "What I'm trying to do" and "What I've done so far", you are heading to the completely wrong direction.
A good thing is you had not been able to get into CwM Recovery, otherwise, you made a mess of your NC.
Just stop "what you've done so far" and follow the link that shumash provided above.
shumash said:
If all you're trying to do is setup a bootable SD card with CM7 on it, and retain the ability to also boot to the stock Nook ROM, try this:
http://forum.xda-developers.com/showthread.php?t=1000957
Click to expand...
Click to collapse
Agreed, you don't need clockwork mod for an SD card install. Follow the directions in my signature (adds some details that verygreen leaves out).
Installing image for CM7
I have a nook color that was purchased just a week ago and had 1.4.0 firmware on it. I had updated it to 1.4.1 before noticing that this particular firmware blocked the nook from being hacked. I had read in one of the threads how to revert back to 1.4.0, adding acclaim.zip file to the sd card would do the trick. I tried this and when my nook went to sleep, nothing. I ended up using the nook-complete-restore-1.0.1.zip with a clockworkmod recovery file and followed steps provided in other threads. Then I was stuck at the "n" screen and could not get any further. With an additional 8 Factory resets and doing the complete restore a second time I was able to get back to what I believe is factory. The difference is, out of the box I had 1.4.0 and now I have 1.3.0. I believe this is fine.
I am wanting to put CM7 with google apps on my nook. I have read a thread that suggested putting an agnostic size image file and when used, my 16gb sd card went down to >200 mb. What is a good image file to use for my card or what am I doing wrong? I am using Win32DiskImager to write my images. I have tried generic-sdcard.img for both 1.1 and 1.3 and the above still happens. I loose over 14gb of space.
I have downloaded the following to use once I have figured out what image to use. update-cm-7.1.0-encore-signed.zip for my CM7 and gapps-gb-20110828-signed.zip for my google apps.
Thanks for all the hard work that is put into making our nook experience the best!!!
dhed73 said:
[...] The difference is, out of the box I had 1.4.0 and now I have 1.3.0. I believe this is fine.
Click to expand...
Click to collapse
If you're installing CM anyhow, the version of B&N running is not important, correct.
I am wanting to put CM7 with google apps on my nook. I have read a thread that suggested putting an agnostic size image file and when used, my 16gb sd card went down to >200 mb.
Click to expand...
Click to collapse
Going by that name, you were doing a CM install to SD. If you'd completed that process, it would have made use of the rest of your SD card.
What is a good image file to use for my card or what am I doing wrong?
Click to expand...
Click to collapse
Are you trying to:
1. Root stock (doesn't sound like it)
2. Install CM to SD for dual boot
3. Install CM to eMMC
I have downloaded the following to use once I have figured out what image to use. update-cm-7.1.0-encore-signed.zip for my CM7 and gapps-gb-20110828-signed.zip for my google apps.
Click to expand...
Click to collapse
You might want to check out CM 7.2 RC0 Mirage (search here). It incorporated all of the fixes and some optimizations up through CM n253.
I am wanting to install CM to SD for dual boot. I have completed the process for adding the image to my card. The problem is that, after adding the image I now have 115mb on my 16gb card. If, I go ahead and install to my SD card will the space on the card be opened up or do I have to do something else?
dhed73 said:
I am wanting to install CM to SD for dual boot. I have completed the process for adding the image to my card. The problem is that, after adding the image I now have 115mb on my 16gb card. If, I go ahead and install to my SD card will the space on the card be opened up or do I have to do something else?
Click to expand...
Click to collapse
If you're getting that 115mb number from your PC card reader on Windows, that's misleading because that's just the size of the boot partition. There are other partitions on the card that take up space and are formatted to be used by CM7. Boot into CM7 on the SD card and see how much space you've got on the /sdcard partition. It should be many gb.
To see how the card is partitioned and the sizes in Windows, get Easeus Partition Master. It's free. If the last partition (the 4th) isn't fully allocated, use Easeus to do it. Don't resize any of the other partitions until you really know what you're doing.
shumash said:
If you're getting that 115mb number from your PC card reader on Windows, that's misleading because that's just the size of the boot partition. There are other partitions on the card that take up space and are formatted to be used by CM7. Boot into CM7 on the SD card and see how much space you've got on the /sdcard partition. It should be many gb.
To see how the card is partitioned and the sizes in Windows, get Easeus Partition Master. It's free. If the last partition (the 4th) isn't fully allocated, use Easeus to do it. Don't resize any of the other partitions until you really know what you're doing.
Click to expand...
Click to collapse
I have a issue with downloading cm7 on a sd card ive followed all the steps and boot it and it downloads and restarts and seems to be working but the touch screen isnt working. My nook is version 1.3 any help would be appreciated.
lesdavid said:
I have a issue with downloading cm7 on a sd card ive followed all the steps and boot it and it downloads and restarts and seems to be working but the touch screen isnt working. My nook is version 1.3 any help would be appreciated.
Click to expand...
Click to collapse
I had the same problem when I had to restore my nook color. I ran the program, in my case the nook system restore file, a second time. After I had done this, my touch screen was back working.
---------- Post added at 07:53 PM ---------- Previous post was at 07:48 PM ----------
shumash said:
If you're getting that 115mb number from your PC card reader on Windows, that's misleading because that's just the size of the boot partition. There are other partitions on the card that take up space and are formatted to be used by CM7. Boot into CM7 on the SD card and see how much space you've got on the /sdcard partition. It should be many gb.
To see how the card is partitioned and the sizes in Windows, get Easeus Partition Master. It's free. If the last partition (the 4th) isn't fully allocated, use Easeus to do it. Don't resize any of the other partitions until you really know what you're doing.
Click to expand...
Click to collapse
shumash,
Thanks..... after downloading the easeus partition file I found that you were correct and I had 14gb left over. I had a hard time booting into recovery for the google app file but, it finally happened. I am up and running and want to thank everyone for the help.
gallahad2000 said:
Agreed, you don't need clockwork mod for an SD card install. Follow the directions in my signature (adds some details that verygreen leaves out).
Click to expand...
Click to collapse
Many thanks. The instructions in your signature worked perfectly. Just curious: is there a freeware image-making software app that doesn't expire after 30 days?
I have a Nook Color. Somehow (and I really can't recall how), I can no longer get to the B&N side of my Nook. Even with the micro-SD out, I still go directly into CYANOGEN. To make matters worse, every single app I try to get from the market will not download. Once I 'Accept & download', the app starts to download then I get an Error overlay screen: "name-of-software" could not be downloaded due to an error.
So I have a V--E--R--Y generic tablet that can't do much. Please help.
Thanx in advance...................................
How did you go about installing CM7? Did you install it to the internal storage?
Please help!!! Noobie messed up NC (big time)
That's part of the problem. I did not consciously install to internal memory, I wanted it to boot from the SD card.
That's what I did...
That's what I did once. I unwittingly installed it onto the internal memory. It also happened to be really buggy. I restored it to stock using Clockworkmod Recovery. Did you use the installer for the SD card?
On a 16GB microSD, I used Win32DiskImager to write 1gb_clockwork-3.2.0.1-eyeballer to a newly-formatted SD card.
I put the ZIP file for: gapps-gb-20110828-signedgapps-gb-20110828-signed, and gapps-gb-20110828-newtalk-signed.
I tried the home-power key combo. It asks me if I'm sure that I want to restore to the factory. I say "Yes" but when the Nook starts up, I'm still in cyanogen mod.
Should I (re-)format the MicroSD, write 1gb_clockwork-3.2.0.1-eyeballer (or another version) then move recovery-clockwork-3.2.0.1-encore?
Aside from not being able to get back to B&N-supplied software, I can't do anything with the NC as an Android tablet.
OP, do you intend to install CM7 into the internal memory?
All I'm trying to accomplish is to get back to the factory NC settings. Once I can get there, I'll decide.
How to hard reset and Factory Default Nook Color - http://goo.gl/pSFui
Power down your NC. Wait approximately 10 seconds or so-- just give it a bit of a break between shut down and factory reset.
Press and hold power button and your "N" home button almost simultaneously-- press Power first and then the N.
Hold these until your screen flashes the "Touch the future of reading" message; hold for a second or two afterward, then release. You will then get a prompt asking if you want to reset your nook to factory. Press the home button to continue. It will ask you to confirm. Press the home key again. Your nook will deregister, reset, and when it reboots, you will see "Kate" in her tutorial video, as if you'd never registered it in the first place.
(Obviously your account info will still be valid-- simply register with your email/pw combo instead of creating a new account.)
Hope this helps- if so please click thanks
Sent from my MB860 using XDA App
I did this (more than once - grrrrrrrrrrrrr!). I never see the "touch the future....." message. Instead, I get a cyanogen mod 7 screen with the message "Booting into Recovery". Then I get a sickly yellow-greenish screen that asks (twice) if I want to teset. I confirm both times then it "wipes" the data. It then boots into a cyanogen mod 7 screen (and the skateboarding 'droid) and I go through the registration process.
Now, when I select a Google app, the downloading (Google Maps) seems to be taking forever, but at least I'm not getting the error I got before.
Also, I do not see the progress of the download that I'm used to seeing on my phone. All I see is "movement" under the "Downloading..." message. How long do I leave it before I abort the download?
Your micro sd card is removed right?
Sent from my MB860 using XDA App
mike11050 said:
On a 16GB microSD, I used Win32DiskImager to write 1gb_clockwork-3.2.0.1-eyeballer to a newly-formatted SD card.
I put the ZIP file for: gapps-gb-20110828-signedgapps-gb-20110828-signed, and gapps-gb-20110828-newtalk-signed.
I tried the home-power key combo. It asks me if I'm sure that I want to restore to the factory. I say "Yes" but when the Nook starts up, I'm still in cyanogen mod.
Should I (re-)format the MicroSD, write 1gb_clockwork-3.2.0.1-eyeballer (or another version) then move recovery-clockwork-3.2.0.1-encore?
Aside from not being able to get back to B&N-supplied software, I can't do anything with the NC as an Android tablet.
Click to expand...
Click to collapse
Eyeballer is a clockwork recovery bootable SD image which is used to install stuff (e.g. CM7) to internal memory.
http://forum.xda-developers.com/showthread.php?t=1030227
VeryGreen (size agnostic thread) is the SD image which creates a full OS on the SD card itself leaving the internal memory alone.
http://forum.xda-developers.com/showthread.php?t=1000957
You have used the Eyeballer method and have therefore done an internal install. You must also have installed a CM7 zip not just the gapps zip as they are just google apps and not an actual ROM.
You have 2 ways forward.
The simplest is if you want to end up with internal CM7 and are not interested in running the B & N ROM. Start again by creating the Eyeballer SD card using win32diskImager. Make sure you use a real USB SD adapter and not a card slot on a laptop. Put onto the card the CM7 ROM zip. I recommend the one from the KANG MiRaGe thread in the development forum. It is the most up to date and stable version available at the moment. Also put on one gapps zip (20110828). Now put the card in Nook, Power up and when in recovery then use the menus to format system, data and cache. Do NOT format boot. Then flash the CM7 ROM zip, then the gapps zip. Power down and prepare a clean SD card either by reformatting the eyeballer card with something like the HP USB card utility or a partition manager in the PC like miniTools. You could also use a different SD card if you want to keep the eyeballer one for future use. Put the card back in, power up and you should now be in a stable CM7 environment where you can set up wifi, register with the Google market and download apps.
The second way if you really want to return to stock on the internal and run CM7 of the SD card then use the eyeballer method but instead of flashing CM7 and gapps you now use a return to stock zip. Make sure you still format the partitions as before.
http://forum.xda-developers.com/showthread.php?t=914690
Once you have it back to stock and upgraded to whatever stock you want then follow the VeryGreen method from the link above. Once the SD card has put CM7 on itself, do not worry that there is only a 114MB space if you ever put the card back in the PC. That is normal; it is just the boot partition that the PC sees. The rest of the card can be seen if you USB connect the Nook to the PC.
Yes it is. Also, even though I'm not getting an error, no apps are loading.
You absolutely rock!!!!!!!!!!!!!!
I'm back at the NC "baseline". I tried to go back to a 1.2 (which is what it came with) using "update-nc-stock-1.2-signed". Once I re-booted, it kept returning to the NOOK COLOR screen. Then I used a 1.0.1 from your last post. It came back fine with 2 exceptions. 1) I now have a message that I need to install a SD card. When I do, my (Windows Explorer) "Computer" screen only recognizes the SD card and not the Nook. These are piddly little issues, but if I can get them fixed, great! (Right now, I cannot upgrade the NC or move any books or load any apps.
Thanks again!!!!!!!!!!!!!!!
mike11050 said:
That's part of the problem. I did not consciously install to internal memory, I wanted it to boot from the SD card.
Click to expand...
Click to collapse
I had this same problem. Since I am a new member, and can't post links, I'm going to try to help.
Install Clockwork Recovery to an SD card. Yes, the same way you did when installing clockwork to the SD the first time.
There are some threads on other fourms (google is your friend) that have links to Update files that allow you to update while keeping clockwork recovery, and some that will remove clockwork recovery. If you can remove the SD card and boot into the Stock Nook OS, then don't worry about installing 1.0.0 or 1.0.1 like some of the forms say. Just place the .ZIP file of the hacked update (usually 1.3 or 1.4 I think) into the root folder of the SD card, then Install it on your NC just like installing CM7 onto the internal memory. Your nook should start working again. It restored mine to full functionality. I can now pay 3 Dollars for angry birds, but at least its not as terribly slow and laggy as it was with CM7.
mike11050 said:
You absolutely rock!!!!!!!!!!!!!!
When I do, my (Windows Explorer) "Computer" screen only recognizes the SD card and not the Nook. These are piddly little issues, but if I can get them fixed, great! (Right now, I cannot upgrade the NC or move any books or load any apps.
Thanks again!!!!!!!!!!!!!!!
Click to expand...
Click to collapse
I had the same issue last weekend, somehow my internal memory had become unrecognizable to anything, and the local Barnes and Noble store had a SD card that repartitioned the internal memory, and I was back in business. And as an added bonus I now have the 4 GB app/BN partition and the 1 GB mostly useless partition.
mike11050 said:
On a 16GB microSD, I used Win32DiskImager to write 1gb_clockwork-3.2.0.1-eyeballer to a newly-formatted SD card. ...
Click to expand...
Click to collapse
The instructions I see when googling around where I see that image mentioned are instructions for installing onto the Nook Color internal memory.
In the simplest case, making an n2a card is much less complicated than that ~ all you need is on the PC, write the size agnostic image, then drop in the CM7 build you want to use, then put the card in the Nook and it creates itself. There are upsides and downsides to different n2a methods, but that one seems to be the easiest ~ I've done it successfully several times, and I'm certainly nothing like an expert when it comes to these Android systems.
A recovery card image will make a bootable recovery card ... and while that might not have been what you needed to get what you want, its what you need to get the nook back to stock.
You might want to go to
http://forum.xda-developers.com/showpost.php?p=22809801&postcount=148
... to get a version of the 1.4.1 upgrade that your recovery card can install. You'll probably have to wipe all sorts of partitions, which means you'll have to sign in with the B&N store again and you'll get to download you B&N apps again, but that's pretty straightforward.
This OP in this thread:
http://forum.xda-developers.com/showpost.php?p=10623716&postcount=1
... says that it will be necessary to format ("wipe") the /data and /system partitions, but it doesn't seem like you'll lose anything you want to keep. After all, you've either overwritten or completely tangled up your stock B&N info.
That post above has 1.4.1. There should be a signed 1.4.2 lying around somewhere, but if not, once its back to stock, you can update to 1.4.2 the normal way, download the B&N update file, drop it in the root of the Nook, make sure its at least 30% charged, and let it go to sleep, which will run the update file.
Hi xda, my nook won't boot up at all after I tried to restore to stock from autonooter 1.01. I read as many threads as I could and tried to make a bootable sd from leapinLar's tips page. The stock recovery with cwr and without. I used winimage and win32. With winImage I get an error "reading from file". win32 seems to write the file but it doesn't boot up the nook. When I try and open the sd with windows to see if anything is on the sd it says "not formatted would you like to format it now". I downloaded file, unzipped, then wrote to sd. I must be doing something wrong creating the sd but I can't find any info as to what. Thanks for any help
Stjpa said:
Hi xda, my nook won't boot up at all after I tried to restore to stock from autonooter 1.01. I read as many threads as I could and tried to make a bootable sd from leapinLar's tips page. The stock recovery with cwr and without. I used winimage and win32. With winImage I get an error "reading from file". win32 seems to write the file but it doesn't boot up the nook. When I try and open the sd with windows to see if anything is on the sd it says "not formatted would you like to format it now". I downloaded file, unzipped, then wrote to sd. I must be doing something wrong creating the sd but I can't find any info as to what. Thanks for any help
Click to expand...
Click to collapse
Are you unzipping the right file? You said something about with stock recovery and without. Those are not image files that can be burned. When you unzip my image zip file, you should end up with a 300MB .img file. That is what you burn with win32diskimager. And take the card out of the PC and put it back in before you try to look at it. And be sure to use an external card reader, not one built into your PC.
Sent from my Nook HD+ using Tapatalk
Thanks Leapinlar. I downloaded your nook color emmc stock recovery zip with and without the cwr. I am using external sd reader. I downloaded and tried cwm-6.0.1.2 bootable sd zip and tried that in the nook and nothing happens. Also tried the 5.5.0.4 version too. I removed the card reader and reinserted it in the pc and when I click on the drive letter it ask me if I want to format it. I used win32diskimager and it said write successful, so I put it in the nook and then plugged nook into computer with the stock usb cable and nothing happens. If I hold the power button down the pc does ding as if when you plug in an external device. I'm either trying to burn the wrong file or I'm not making the bootable. Thank you for your help.
Stjpa said:
Thanks Leapinlar. I downloaded your nook color emmc stock recovery zip with and without the cwr. I am using external sd reader. I downloaded and tried cwm-6.0.1.2 bootable sd zip and tried that in the nook and nothing happens. Also tried the 5.5.0.4 version too. I removed the card reader and reinserted it in the pc and when I click on the drive letter it ask me if I want to format it. I used win32diskimager and it said write successful, so I put it in the nook and then plugged nook into computer with the stock usb cable and nothing happens. If I hold the power button down the pc does ding as if when you plug in an external device. I'm either trying to burn the wrong file or I'm not making the bootable. Thank you for your help.
Click to expand...
Click to collapse
You don't say, but you are unzipping those image files before you burn them, right? Should be 300MB .img file. Other than that just look at my A10 tip in my tips thread and follow exactly.
Sent from my Nook HD+ using Tapatalk
leapinlar said:
You don't say, but you are unzipping those image files before you burn them, right? Should be 300MB .img file. Other than that just look at my A10 tip in my tips thread and follow exactly.
Sent from my Nook HD+ using Tapatalk
Click to expand...
Click to collapse
Yes I did unzip the image file before I burned it. I ended up finding a cwr zip that was for a 4 gig card, probably an older way of doing it, and that worked for some reason. I did use your stock 1.4.3 zip though and all seems well. Your tips page is great, thank you, you're very helpful now I can play around and brick it again with some other stuff.
Hey guys.
I am somewhat a noob. I bought a brand new 8gb nook color from wallmart on black friday. I heard about how you can put CM onto the sd card and boot from that without altering the device itself. I have tried for HOURS to do this. I have looked up COUNTLESS walk throughs and done everything they say, done alternations, and used different cards ranging from 2gb sandisk (class 1?) to 32 gb sandisk this is a class 4. I've used winimage and burned the image to the card, then dragged over cyanogenmod and done this task in countless different ways. Every time I shut down the nook, put in the card, then re-boot, the nook does NOT boot from the card. It boots normal, then I can actually browse the card after it boots up. I have done it EXACTLY how it says here and read tutorials so its not a question of whether or not I have followed standard proceedure. My firmware version is 1.4.3. Ive searched online to this and to no avail. My sister bought the exact same one at the exact same time and it does not boot the sd either. I have done about 8 straight hours of research on this guys, so I'm no pro but I have a basic understanding of how it works now. My questions are this:
1: Did Barns and Noble put restrictions on the newest nook color or on the newest software version? And if so is there a way around this?
and
2: If NOT, is there an alternate way/installation onto the card that I can do (such as an image pre loaded with CM etc.) that I might be able to try instead of the conventional way?
Thanks guys! Sorry for the uber long post : S
ronin8knight said:
Hey guys.
I am somewhat a noob. I bought a brand new 8gb nook color from wallmart on black friday. I heard about how you can put CM onto the sd card and boot from that without altering the device itself. I have tried for HOURS to do this. I have looked up COUNTLESS walk throughs and done everything they say, done alternations, and used different cards ranging from 2gb sandisk (class 1?) to 32 gb sandisk this is a class 4. I've used winimage and burned the image to the card, then dragged over cyanogenmod and done this task in countless different ways. Every time I shut down the nook, put in the card, then re-boot, the nook does NOT boot from the card. It boots normal, then I can actually browse the card after it boots up. I have done it EXACTLY how it says here and read tutorials so its not a question of whether or not I have followed standard proceedure. My firmware version is 1.4.3. Ive searched online to this and to no avail. My sister bought the exact same one at the exact same time and it does not boot the sd either. I have done about 8 straight hours of research on this guys, so I'm no pro but I have a basic understanding of how it works now. My questions are this:
1: Did Barns and Noble put restrictions on the newest nook color or on the newest software version? And if so is there a way around this?
and
2: If NOT, is there an alternate way/installation onto the card that I can do (such as an image pre loaded with CM etc.) that I might be able to try instead of the conventional way?
Thanks guys! Sorry for the uber long post : S
Click to expand...
Click to collapse
No nothing was done by B&N. It is how you are burning the card. It will not boot in the nook unless burned perfectly. Look at my tips thread linked in my signature and read items A9 and A10.
There not any easy was not to use a bootable recovery card. Just keep trying, using different software, different cards, different PC s, different card readers.
Sent from my Nook HD+ using Tapatalk
ronin8knight said:
Hey guys.
I am somewhat a noob. I bought a brand new 8gb nook color from wallmart on black friday. I heard about how you can put CM onto the sd card and boot from that without altering the device itself. I have tried for HOURS to do this. I have looked up COUNTLESS walk throughs and done everything they say, done alternations, and used different cards ranging from 2gb sandisk (class 1?) to 32 gb sandisk this is a class 4. I've used winimage and burned the image to the card, then dragged over cyanogenmod and done this task in countless different ways. Every time I shut down the nook, put in the card, then re-boot, the nook does NOT boot from the card. It boots normal, then I can actually browse the card after it boots up. I have done it EXACTLY how it says here and read tutorials so its not a question of whether or not I have followed standard proceedure. My firmware version is 1.4.3. Ive searched online to this and to no avail. My sister bought the exact same one at the exact same time and it does not boot the sd either. I have done about 8 straight hours of research on this guys, so I'm no pro but I have a basic understanding of how it works now. My questions are this:
1: Did Barns and Noble put restrictions on the newest nook color or on the newest software version? And if so is there a way around this?
and
2: If NOT, is there an alternate way/installation onto the card that I can do (such as an image pre loaded with CM etc.) that I might be able to try instead of the conventional way?
Thanks guys! Sorry for the uber long post : S
Click to expand...
Click to collapse
Use win32diskimager instead and use an external card writer. The image is approximately 300mb with the Rev5 file. Then copy the CM10 and 2021011 GApps zips to SD card. Insert in Nook Color. Wait for setup to finish and shut down. Start Nook. Enjoy.
I used ManualNooter for my nook. As I recently installed a bunch of apps and ebooks, I thought I should back up my device. I went to Rom Manager for back up which then brought me to CWM when it was done to reboot. When I reboot it was stuck in boot loop. I turned the nook, then back on and whenever i reboot i get black screen of death. I can boot to CWM by holding all three buttons down. I tried wiping data, factory reset, reinstalling nooter zip, yet every time I reboot, I get black screen of death. Can someone help me figure out how to fix this? Thx.
kellym said:
I used ManualNooter for my nook. As I recently installed a bunch of apps and ebooks, I thought I should back up my device. I went to Rom Manager for back up which then brought me to CWM when it was done to reboot. When I reboot it was stuck in boot loop. I turned the nook, then back on and whenever i reboot i get black screen of death. I can boot to CWM by holding all three buttons down. I tried wiping data, factory reset, reinstalling nooter zip, yet every time I reboot, I get black screen of death. Can someone help me figure out how to fix this? Thx.
Click to expand...
Click to collapse
Go to my NC tips thread linked in my signature and read item A15. That will restore you to stock and you can start over.
Sent from my Nook HD running CM10.1 on SD
leapinlar said:
Go to my NC tips thread linked in my signature and read item A15. That will restore you to stock and you can start over.
Sent from my Nook HD running CM10.1 on SD
Click to expand...
Click to collapse
My computer no longer recognizes the Nook (I have an HP laptop running Windows 8). Prior to the black screen, the computer did detect the nook when plugged in with the USB cable. How can I now copy the zip file to flash through CWM recovery? I have version 3.2.0.1 installed? I don't understand why trying to make a back-up file through the ROM manager would cause such failure? Thanks for your help.
EDIT: Should I now be trying the verygreen method via SD card? Apologies for the panic.
kellym said:
My computer no longer recognizes the Nook (I have an HP laptop running Windows 8). Prior to the black screen, the computer did detect the nook when plugged in with the USB cable. How can I now copy the zip file to flash through CWM recovery? I have version 3.2.0.1 installed? I don't understand why trying to make a back-up file through the ROM manager would cause such failure? Thanks for your help.
EDIT: Should I now be trying the verygreen method via SD card? Apologies for the panic.
Click to expand...
Click to collapse
Make a bootable CWM card as described in my item A10. Then copy the 1.4.3 rom zip downloaded from A15 to the card. Put the card in the Nook, boot to CWM and flash the ROM zip.
Sometimes files get corrupted when writing them to the Nook. Obviously that is what happened with ROM Manager.
Sent from my Nook HD+ running CM10 on Hybrid SD
leapinlar said:
Make a bootable CWM card as described in my item A10. Then copy the 1.4.3 rom zip downloaded from A15 to the card. Put the card in the Nook, boot to CWM and flash the ROM zip.
Sometimes files get corrupted when writing them to the Nook. Obviously that is what happened with ROM Manager.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
What size SD card do I need? I tried copying the 1.4.3 rom zip (unzipped, used 7 zip to extract the other files) onto a 8 GB sandisc and a 16GB and both tell me the card does not have enough space. I've used Win32diskimager-v.07 (the link from manual nooter no longer works), I copied the CWM-5.5.04 image to the SD card. I had no trouble copying manual nooter onto the 8gb sandisc. I used a SD formatter program to format and wipe the disk before using it for this. Thanks.
kellym said:
What size SD card do I need? I tried copying the 1.4.3 rom zip (unzipped, used 7 zip to extract the other files) onto a 8 GB sandisc and a 16GB and both tell me the card does not have enough space. I've used Win32diskimager-v.07 (the link from manual nooter no longer works), I copied the CWM-5.5.04 image to the SD card. I had no trouble copying manual nooter onto the 8gb sandisc. I used a SD formatter program to format and wipe the disk before using it for this. Thanks.
Click to expand...
Click to collapse
I guess I should modify my instructions. The 1.4.3 zip is so large that you need to use the 6.0.1.2 version of the bootable CWM SD. It has a little more room for the zip. It does not matter which size card you start out with.
Sent from my Nook HD+ running CM10 on SD
leapinlar said:
I guess I should modify my instructions. The 1.4.3 zip is so large that you need to use the 6.0.1.2 version of the bootable CWM SD. It has a little more room for the zip. It does not matter which size card you start out with.
Sent from my Nook HD+ running CM10 on SD
Click to expand...
Click to collapse
I'm back in business! It worked - whew! I had trouble with the 1.4.3 zip, so I used DizzyDen's 1.4.1. I was stuck in boot loop the first time I rebooted, then used the 5-6-7 partition fix zip, reinstalled the 1.4.1 zip and it worked like a charm. I also used the newer version of CWM you advised which was smaller in size, it's all on the 16gb SD card with no issue.
One last question, now that the stock rom is in order, am I safe to flash CM10? I'd prefer not to use manualnooter again as you said in a previous post, CM10 is leaps and bounds above nooter. If you think it's okay to flash, do I have to do the 8 count reset to fully wipe?
Many, many thanks for your clear, detailed instruction and patience!
kellym said:
One last question, now that the stock rom is in order, am I safe to flash CM10? I'd prefer not to use manualnooter again as you said in a previous post, CM10 is leaps and bounds above nooter. If you think it's okay to flash, do I have to do the 8 count reset to fully wipe?
Click to expand...
Click to collapse
Glad you got it working. No, you don't need to reset. Just flash that 567 zip again and flash the CM10 rom. All should be ok.
Sent from my Nook HD+ running CM10 on SD
leapinlar said:
Glad you got it working. No, you don't need to reset. Just flash that 567 zip again and flash the CM10 rom. All should be ok.
Sent from my Nook HD+ running CM10 on SD
Click to expand...
Click to collapse
When I was last working on this, I had my external hard drive plugged into the computer via the usb port. I was backing up the files that were on my micro sd card, I had a 16gb in my droid bionic, I swapped it with the 8 gb I had in the nook when I couldn't get the older version of CWM on the card. Now when I plug in my external hard drive, all I see are the win32 imaging files on it. I take it, this process formats over everything plugged into a usb port? I've lost all my kids photos and videos, I can cry I'm so mad at myself for letting this happen. I've tried the two laptops we have and I get the same list of files in the folders. I guess this is one of those mistakes you only make once.
Oh no! Yes, burning a card writes over everything. There are some utilities that may let you rescue your old files, but maybe not. I would set it aside till you find out. I think the free MiniTool Partition Wizard has some paid companion products that may help.
Edit: just reread your post. It does not write over everything plugged into the USB. You just made a mistake when you burned once and selected the external drive letter. The same solution applies. Find a disk partition repair utility.
Sent from my Nook HD+ running CM10 on Hybrid SD
Status 7 error
leapinlar said:
Glad you got it working. No, you don't need to reset. Just flash that 567 zip again and flash the CM10 rom. All should be ok.
Sent from my Nook HD+ running CM10 on SD
Click to expand...
Click to collapse
I finally found the time to do this. I flashed the 567 zip, then went to the CM10 download page for the 414 nightly encore zip. I received two errors:
symlink: some symlinks failed
E:error in /sdcard/cm-10-20130414-NIGHTLY-encore.zip
(Status 7)
Installation aborted.
What does this mean?
Thank you.
kellym said:
I finally found the time to do this. I flashed the 567 zip, then went to the CM10 download page for the 414 nightly encore zip. I received two errors:
symlink: some symlinks failed
E:error in /sdcard/cm-10-20130414-NIGHTLY-encore.zip
(Status 7)
Installation aborted.
What does this mean?
Thank you.
Click to expand...
Click to collapse
I suspect a bad download of the CM zip. Try downloading again.
Sent from my Nook HD+ running CM10 on Hybrid SD
You were right (of course!). I took the 407 zip and it flashed without issue. Very exciting! Thank you!
Sent from my DROID BIONIC using xda app-developers app
leapinlar said:
I suspect a bad download of the CM zip. Try downloading again.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
Am I able to copy files to the SD card while it's running CM10? I wanted to copy some pdfs and ebub books to read and when I try to copy to the SD card it says the Nook is not responding or disconnected. I don't think this is a driver issue as I can see the Nook on my computer and can see the files stored either on internal storage or SD. When I'm in CM10 and go to file manager, I can only see what is on the SD card, I can't access any of my files that were on EMMC. That's fine, I have copies of my ebooks saved on my laptop, I just can't figure out how to read them now. Any thoughts?
Thanks.
kellym said:
Am I able to copy files to the SD card while it's running CM10? I wanted to copy some pdfs and ebub books to read and when I try to copy to the SD card it says the Nook is not responding or disconnected. I don't think this is a driver issue as I can see the Nook on my computer and can see the files stored either on internal storage or SD. When I'm in CM10 and go to file manager, I can only see what is on the SD card, I can't access any of my files that were on EMMC. That's fine, I have copies of my ebooks saved on my laptop, I just can't figure out how to read them now. Any thoughts?
Thanks.
Click to expand...
Click to collapse
You need to be a little more specific.
There are two methods to connect to your PC with CM10 using the USB cable, MTP and USB mass storage. They are selectable in settings. Go to settings, storage, menu and USB computer connection. MTP is default and shows the Nook as just devices in Windows Explorer with no drive letters. If you choose USB mass storage, they show as drive letters in Windows explorer. But they do not contain anything until you activate them by touching a button on your Nook. And the button does not show if Android degugging is activated in settings.
So that is why I say you need to be more specific.
You say you can't copy to the SD. What are you seeing on your PC, drive letters or just labels that say internal SD and sdcard? And describe a little more the errors.
The reason you can't see emmc with the file manager that comes with CM10 is by default it is in safe mode. You have to change a setting to get it in root mode. Either get a different file manager like the free Root Browser Lite or change the setting in the CM10 file manager. To change the setting, press menu while it is open and you will see three dots in the lower right. Touch that. Go to settings, general settings and access mode and change it from safe to root. Then you will be able to see emmc.
Sent from my Nook HD+ running CM10 on Hybrid SD
I think my quick reply didn't post. Anyway, thanks, again, for your help. When I went to transfer files from my external hard drive to the Nook, I was using the wrong lap top and then realized I had to update usb drivers which helped. I then followed your other steps to change settings, including safe to root, and I can now see all my files.
Can you recommend a file manager? The default one is a bit cumbersome.
Thanks again for everything.
kellym said:
I think my quick reply didn't post. Anyway, thanks, again, for your help. When I went to transfer files from my external hard drive to the Nook, I was using the wrong lap top and then realized I had to update usb drivers which helped. I then followed your other steps to change settings, including safe to root, and I can now see all my files.
Can you recommend a file manager? The default one is a bit cumbersome.
Thanks again for everything.
Click to expand...
Click to collapse
If you want a free one, I recommend Root Browser Lite. For paid, I like Root Explorer.
Sent from my Nook HD+ running CM10 on Hybrid SD
I'd like to update to the May 4 nightly and new gapps, should I run the 567 partition zip again before flashing? If so, should I wipe cache and dalvik as well? Are you still using ADW launcher? I'm using Nova. Thanks.
Sent from my ME172V using xda app-developers app
kellym said:
I'd like to update to the May 4 nightly and new gapps, should I run the 567 partition zip again before flashing? If so, should I wipe cache and dalvik as well? Are you still using ADW launcher? I'm using Nova. Thanks.
Sent from my ME172V using xda app-developers app
Click to expand...
Click to collapse
The 5/4 nightly is CM10.1. The version you were running earlier was CM10. You should be able to just flash the 5/4 nightly with only wiping the dalvik-cache. No other wiping or partition zips. Since CM10.1 requires a newer gapps (20130301), you should flash that too.
Yes, I still use ADW, but only because I am used to it and do not want to try something new.
Sent from my Nook HD+ running CM10.1 on emmc
Is there any difference in performance running CM10.1 off emmc vs SD card which I'm presently doing with the April 7 nightly? I have some vague idea that I read a while back once you put CM10 on emmc you could no longer return to stock?
If I stay on SD card is there any harm in trying (I think the name is Dean) method to adjust internal partition for more room for apps? I've run out of room on SD card? Or is using Titanium to move files a safer alternative?
My kids are now using the Nook, I won an ASUS tablet from livinginkaos over at the Droidrzr forum. He had a give-away while fundraising for a root exploit bounty for JellyBean which Dan Rosenberg created. Method works using Linux Ubuntu, that forum is awesome. I was singing your praises to them. Android forums have the greatest support! Thx.
Sent from my DROID BIONIC using xda app-developers app
[Caveat emptor: adopt/follow this guide at your own risk].
FWIW, here the process I used to install CM11 internally (on emmc*) on my HD+:
Using a disk partition tool (such as MiniTool Partition Wizard Home Edition) create on SD card a Primary FAT32 partition, and set the partition ID type for the partition to 0x0C FAT32 LBA and set its Active flag. Once this is done, the partition should appear as a (read/write accessible) drive under Windows.
Use an archive file manager such as 7-zip and extract the .img file from verygreen’s emmc-cwm-early3.1.img.gz (http://forum.xda-developers.com/showpost.php?p=49192422&postcount=1)
Use the archive file manager to extract the files from the .img file and copy them to the SD card: first MLO, then next u-boot.bin, uImage, kernel, ramdisk.cwm.
Copy to the SD card:
verygreen’s flashable CWM recovery zip file cwm-recovery-ovation-6.zip (http://forum.xda-developers.com/showpost.php?p=49192422&postcount=1)
the zip file of CM11 ROM build of your choice – e.g., from http://download.cyanogenmod.org/?device=ovation (see http://www.cyanogenmod.org/blog/cm-11-m4-post-release-items for considerations in choosing nightlies vs. snapshot/stable builds)
the zip file of the Gapps package corresponding to CM11 – e.g., http://opengapps.org/?api=4.4&variant=nano
Put the SD card into the HD+, and boot from its power-off state.
[Optional step but highly recommended] Select Backup to backup your HD+ current ROM config (/boot, /recovery, /system, and /data).
Select Wipe data & factory reset.
Select install zip from SD card and install flashable CWM recovery zip file.
Select install zip from SD card and install CM11 zip file.
Select install zip from SD card and install Gapps zip file.
Remove SD card and select reboot.
Once the HD+ boots up, set up the wifi connectivity and your google account info.
If the Nook fails to boot off SD -- the two most common symptoms of failed SD boot and their likely causes are:
The HD+ boots straight to stock -- most likely the boot partition's type and/or flag are not correctly set, or the HD+ cannot find the MLO in the boot partition (make sure that MLO is the very first file to be copied to the freshly made /boot partition).
If the HD+ consistently boots straight to stock in spite of a valid /boot partition and boot files, it's possible that the tablet is one of those HD+ units that have difficulty booting of SD cards, see http://forum.xda-developers.com/showthread.php?t=2288688 for more info and potential remedies.
The HD+ screen stays dark for seemingly a long time then eventually boots to stock -- most likely the MLO or u-boot.bin are corrupted. When in doubt, compare the size of the two copies of the files in bytes.
HOW-TO Guides for Installing CyanogenMod on Nook HD+
Installing CM11 Internally on Nook HD+ (this guide)
Building a CM11 SD card with Customized Partition Sizing for HD+
Updating HD+ Internal EMMC to CM11 from CM10.x
What to download?
Hey Guys,
First off I really appreciate the time you take to answer my questions.
I still need some guidance however.
Again I have "Android 2.2" The last stock upgrade they updated.
So with that being said. What files should I download, and what order.
Everyone is giving me different links and i am not sure what to do.
This is my first time every doing something like this on a nook or tablet.
So please be patient with me. I would greatly appreciate it.
Should I download the cyanogenmod software first to my nook folder on my computer desktop, and then what other files do I need?
Once I download them I plan to transfer them over to a card for my usb slot that is on the bottom of my nook I am assuming, correct?
Once I have the software I need, Then I need to know what order should I install what first.
When I am doing this software installs. Do I need to worry about what is on there now.
This is nothing I need to save so I am not afraid of loosing what ever is on the nook at the moment.
All of this stuff can be let go or deleted or refresh install. Don't care.
I just want to get my table to work like a computer basically. So, I can watch the videos that i want to watch on my tablet, and still
be able to surf the net and read internet websites, you tube .com and other websites I like of course.
By doing this process this will still allow me to do this I am assuming. Again, I have never mode so I am not sure what this
cyanogenmod is or what it can do to help. I am game for trying to do it if it gets me what I want it to do.
I did see the other links posted above. I just diidn't know where to start or what to download first do to the fact I have only 2.2 android software on my nook color hd+
Again, I appreciate the advice peeps!
Please elaborate if you can with what links and what to do. Thanks again. Karl
kjames1973 said:
Hey Guys,
First off I really appreciate the time you take to answer my questions.
I still need some guidance however.
Please elaborate if you can with what links and what to do. Thanks again. Karl
Click to expand...
Click to collapse
First of all, you need to realize that installing any kind of aftermarket ROM on your android device will void your warranty with no manufacturer support.
Second, installing ROMs is inherently risky, since there is always the possibility of bricking your device.
Thirdly, any kind of ROMs that you see in the Android Development section are not completely stable; they are usable but there will be bugs & glitches. So all ROMs come with a caveat: use at your own risk!
That being said, here's how it works:
You will need three files; (a) SD Card Image (b) Recovery Image (c) ROM that you want to install.
For this purpose I am using CM11 as the example, the thread is here.
[1] Every Android device has a manufacturer installed recovery program; to install a custom ROM you need to have a custom recovery. This custom recovery is what allows you to make changes to your Android device.
[2] The Nook HD+ has the advantage of being able to boot from its SD card slot (kinda like a computer booting from a CD/DVD drive).
[3] Download the image files and create a bootable SD card. Copy the Recovery Image and the ROM to this SD card. You will need WinImage to create this card in a Windows computer.
[4] Insert this card into the HD+ and reboot your device. Here's the kicker, the HD+ may not boot from the SD card and may simply go to normal boot. If that happens you will have to keep repeating it. Check older threads about this issue.
[5] Once it boots from the SD Card, follow the instructions listed in the first post of that thread.
Brief summary (this is true for most devices): Create a bootable SD card, use this card to boot the device, install Custom recovery into the device, then install the ROM. Once you have a custom recovery installed, you won't ever have to use the bootable card again unless you run into some issues.
Good Luck!
For Hirent.
Hirent,
First off, I want to say thank you so much for the very detailed reply you sent my way.
I will use this with digression of course. I am aware of the warranty issues that it will cause.
The one major question I have before I dive into this project.
I am aware of the possible bugs and how it is not perfected.
Will this enable me to download and install flash player on a updated android that was suggested in this article you posted?
Or will it just work automatically after I do the project of these software installs. Another words I will be able to open chrome or factory
browser and go to NHL.com, MLB.com, NBA.com and other s and play the videos on the Nook HD+ Color after installs or no?
Thanks for the advice, help, and replies.
Karl
kjames1973 said:
...
The one major question I have before I dive into this project.
I am aware of the possible bugs and how it is not perfected.
Will this enable me to download and install flash player on a updated android that was suggested in this article you posted?
Or will it just work automatically after I do the project of these software installs. Another words I will be able to open chrome or factory
browser and go to NHL.com, MLB.com, NBA.com and other s and play the videos on the Nook HD+ Color after installs or no?
...
Click to expand...
Click to collapse
FWIW, I am running CM11 (M11 snapshot build: http://download.cyanogenmod.org/?device=ovation&type=snapshot) on my HD+, and Flash works reasonably well on the Chrome browser.
New Issue with SD Card 8gb, Centon
Hello,
I tried to follow the instructions on deleting partition on SD card. I also did get it wipe. But, the new issue is I am not able to go any further in the process.
I tried to read the card in my computer and now the card is not being recognized by windows on "my computer" It is H Drive.
IT was now its not. I deleted partition then was going to try to create the new partition. That was not highlighted on the partition magic software.
The article I was following was this.
https://www.youtube.com/watch?v=fLbr1Uyr0sk
Now my SD card is not being recognize by windows 7 ultimate.
I also tried to do the right click trick on my computer then computer management. Then did click storage and then drive then so on.
However when I did that, only that screen recognizes my sd card before and after. But no other screens like my computer screen.
What do I do next with this card to continue. I was trying to follow that tutorial above then go to the windows disc 32 part.
Then drag the software over to start installing it on my nook. But, obviously I never got that far. Can you help me get the SD card to work again and tell me what I did wrong and what to do next so I can move forward to add CW & whatever android software will work well with flash. So I can use the other sites I mentioned in my other post.
If anyone can help I would appreciate it. I am stuck and not sure what to do next.
---------- Post added at 05:41 AM ---------- Previous post was at 05:33 AM ----------
Weird.
I just put the sd card in a usb card dongle that inserts the sd card into usb thumb drive and all of the sudden I see the drive on this computer now.
What should I do now?
Do I still have to go and do the windows disc 32 imager part.
Then drag and drop the software I need and drop in the card to my nook then install.
Or just drag software that I need like CM and Android and move forward with that.
Which should I do first. If it is the later part, which CM and Android should I use for the Nook color HD +?????
Thanks again for help and sorry about that first post, I swear it was it seeing it before. Weird.
Thanks, Karl
Google Play
I've followed all of the instructions and downloaded recovery, CM12 (cm-12.1-20160220-NIGHTLY-m7.zip), and gapps for 6.1. The system boots and I an navigate; however, Google play is not loading, when using the browser the content area becomes untouchable (touch screen in areas of the body of the page doesn't work), and there is not choice to set up a google account.
Any advice would be appreciated!
ummhasan said:
I've followed all of the instructions and downloaded recovery, CM12 (cm-12.1-20160220-NIGHTLY-m7.zip), and gapps for 6.1. The system boots and I an navigate; however, Google play is not loading, when using the browser the content area becomes untouchable (touch screen in areas of the body of the page doesn't work), and there is not choice to set up a google account.
Any advice would be appreciated!
Click to expand...
Click to collapse
What tablet are you having this issue with?
AFAIK currently there is no CM12 nightly build yet for the Nook HD+ ("ovation") or HD ("hummingbird"). Make sure you pick the CM build specific for your device (e.g., cm-11-20160208-NIGHTLY-ovation.zip for the Nook HD+); using a ROM build for a different device can brick your tablet.
Sent from my BN NookHD+ using XDA Premium HD app
Nook HD+ and Google Play
Thanks for your quick reply. This must be the problem. I originally installed the CM11 and Google Play did not work so I went out and found another 'walk through' via the link given to me last time and thought CM12 was the right choice.
I'll go back and reformat after getting the right gapps for CM11.
digixmax said:
What tablet are you having this issue with?
AFAIK currently there is no CM12 nightly build yet for the Nook HD+ ("ovation") or HD ("hummingbird"). Make sure you pick the CM build specific for your device (e.g., cm-11-20160208-NIGHTLY-ovation.zip for the Nook HD+); using a ROM build for a different device can brick your tablet.
Sent from my BN NookHD+ using XDA Premium HD app
Click to expand...
Click to collapse
ummhasan said:
Thanks for your quick reply. This must be the problem. I originally installed the CM11 and Google Play did not work so I went out and found another 'walk through' via the link given to me last time and thought CM12 was the right choice.
I'll go back and reformat after getting the right gapps for CM11.
Click to expand...
Click to collapse
For CM11 I'd suggest you use the GApps package http://opengapps.org/?api=4.4&variant=nano.
digixmax said:
For CM11 I'd suggest you use the GApps package http://opengapps.org/?api=4.4&variant=nano.
Click to expand...
Click to collapse
Thanks, so what I did go back and reformat the sd card and start over with the early, cm recovery ovation, cm11, gapps 4.4; however, apparently I didn't unzip and copy the early correctly because after I rebooted the hd+ after going through the wipe/install process, I got an error that the setup wizard could not start. I powered off, wiped the sd card and began again following directions very carefully making sure the MLO was copied first.
Now, it seems I have somehow bricked the device because it will not power on and has only a green light when plugged in, instead of the normal amber. Any ideas of how to get it to turn on and boot to the SD again?
EDIT:
Okay, as I stated in my edit, I got it to boot, but I'm still getting the popup "Unfortunately, Setup Wizard has sopped. Any ideas?
Thanks for your time!!!
ummhasan said:
...
EDIT:
Okay, as I stated in my edit, I got it to boot, but I'm still getting the popup "Unfortunately, Setup Wizard has sopped. Any ideas?
...
Click to expand...
Click to collapse
Did you do a "wipe /data & factory reset" before you flash/install the zip files of CM11 ROM and GApps?
Did the installation of the 2 zip files succeed without error messages?
I got it working after I got it to bypass the error by dragging down the menu and connecting to wifi. Once I did that I was able to set up the Google account and everything was fine thereafter. There is a bit of flickering now and then, but everything seems to be working fine now. Thanks so much for your time and help!!!
Recover Data?
Hi,
I've jut reinstalled cm11 onto my nook HD+ & realise I failed to copy a text file over before I formatted the HDD. Is it possible to recover a deleted file off the nook HDD via a PC? I've tried changing the developer option settings - Android debugging on, ADB Over Network on & connecting via USB both MTP & UMS (I think that's what they were) but when I run any of my Data Recovery programs in win7, the drive isn't recognised as an option to recover from.
Any help would be appreciated,
Thanks