Like the topics states my 8125 will fade the screen every time I slide my keyboard open. It does it about halfway through the slide. Also practically non of the buttons on the front work anymore. I was told the ribbon cable may be loose, so I took it apart. I got all the way until the back of the screen seperates from the screen. I was pulling that apart and it didnt want to come so I just stoped in fear of breaking something. It was almost as if glue was holding a board on. Anyways I looked around as best I could and did not see anything. When I turned it back on it started right up but still fades out when slide open. Its been doing this for some time now and I just got back into the the cell phone thing rather then purchasing a new one. NBD ROM but the problem existed way before changing anything on the phone. Any help would be great. TIA
ttt anyone??
You will have to use a clipper preferably a plastic one to seperate the black back panel of the LCD housing,insert the clipper from the side and then run it along the entire panel till the six(i think) clamps unlock,then gently pry the back panel off taking care not to cut the flexi strip,that should do.It is most unlikely that it is a software issue,85% its a strip problem and 15% maybe because of the LCD.
Any chance you mean the ribbon cable when u say strip?
I have had the cable off and visualy looks ok.
any chance there is a replacement cable that I can purchace somewhere?
Hi,
The keyboard stopped working on my device so I opened it up to find the tiny flat keyboard cable not properley seated on the mainboard. I tried putting it back but 1)its SOOOO tine and fidley, and 2) the tiny plastic saddle / clip bit that holds the cable down broke in half.
I suspect it may have been cracked already somehow and that why it came loose.
Anyway, anyone know where I can get one of these little clips? Any tips for putting them back together?
Thanks!
Anthony
So here is my story. I installed a new digitizer for my broken HD2 screen, and ended up creating a crease on the ribbon cable. I managed to also break off half of the lock-in bar (the black bar) on the socket, but it still locks half of the other pins down and in place.
Heres the problem.
I turn on the phone, and the screen lights up but doesn't show me my display. The backlight IS on, but isn't showing the bootup, or anything. I DID manage to get it to show the screen by messing with the cable, but only for a few seconds and then it wouldn't anymore. The phone functions fine, I had a friend send me a text and the phone vibrated, and when I pressed the lock button it locked and unlocked (for my Android ROM). I know it did this because the backlight would turn on and off on the LCD.
Would buying a new LCD fix the problem or does that little black bar on the socket matter? I figured all it did was lock the pins in place so it shouldn't be a big deal..
there is 3 ways out of that.
One put a tape over the back side of the flex. it might work sometimes, but not reliable
Two buy a new socket from ebay and resolder it.
Three hardcorely wire them. It is possible I fixed a broken volume flex before.
the lock does not just hold the cable in place it also pushes it down on the contact face.
You may be able to pack the ribbon on the back to help it fit tighter in the sock & increase pressure to the mating faces, hopefully the rest of cable is serviceable ! extra lock security can be added with tape & ribbon can be reinforced with tape too if helps.
My two-year-old HD2 has developed connector problems shortly after it's first birthday. First the charging/data micro USB connector would increasingly not stay connected, and then the wired handset microphone became intermittent and finally stopped working completely. I tried new handsets and USB cables, but no joy. Turns out the problem in both cases was impacted pocket lint in the phone connectors. No joke. I keep the phone in my front trouser pocket, and over time lint has settled into the connectors and been jammed to the connector bottom each time I plugged in a cable. After a while the impacted lint became hard and sufficiently thick that it interfered with proper seating of the connectors! Solution was to carefully dig it out using a hat pin and some very thin and fine tweezers. Much easier solution than trying to open the HD2 and replace the connectors!
There are many of us in the Nexus 7 community who are looking to build our tablets in to our cars and other places where the power button will not be practically accessible. I am one of those people. I was wondering if anybody had any ideas on how to extend the power button?
The ribbon cable for the power and volume buttons can be seen here: http://www.ifixit.com/Guide/Installing+Nexus+7+Power+&+Volume+Button+Cable/9926/2
The header/connector on the board for the cable looks way too small to solder to and so my latest idea is finding a replacement ribbon cable that I could extend in to a tiny gauge wire and externalize from the case. From what I've been able to find so far, I think this is a ZIF FPC/FFC type ribbon cable and connector? I was thinking of something like this: http://www.mouser.com/ProductDetail...GAEpiMZZMvyL%2b65tEJ/L29YMZjxdjhiuZuU4IfHbXs= But I truly have no idea if this cable will fit? Anybody who's great with PCBs who would like to chime in?
If it helps I found a Molex catalog that has a couple connectors that look similar:
http://www.molex.com/catalog/web_catalog/pdfs/F.pdf
Subscribed!!
Ive been considering the nexus for my car pc aswell. Once i pick mine up i will tear it down and see if a ribbon cable could be either extended or possibly simply cut and have wires soldered to it for external power and volume. I have already designed a power supply for the nexus in the car that would also power a DAC and a HDD. I can provide the part number for the TI power chip that i used if anyone is interested. Its capable of producing 6 amps of current at 5 volts.
physical buttons suck. make all phone with only capacitive buttons,.
Interesting
jllbenson said:
physical buttons suck. make all phone with only capacitive buttons,.
Click to expand...
Click to collapse
How would that make externalizing the buttons as needed in this application any easier..?
irishboym4 said:
Ive been considering the nexus for my car pc aswell. Once i pick mine up i will tear it down and see if a ribbon cable could be either extended or possibly simply cut and have wires soldered to it for external power and volume. I have already designed a power supply for the nexus in the car that would also power a DAC and a HDD. I can provide the part number for the TI power chip that i used if anyone is interested. Its capable of producing 6 amps of current at 5 volts.
Click to expand...
Click to collapse
This is what I ended up doing. I got some good advice from another XDA'er who suggested I just pop the bubble button off the ribbon and solder to the contacts directly. In reality the bubble buttons are on a laminated sticker that I could just peel back. Then I soldered to the pads and pushed the cables out through where the rubber for the power button used to be. So far things seem to be working well, I'm a little weary of how this soldering will survive the swings in temperature being left in the car, but I guess there's only one way to find out. Observe:
dmexs said:
How would that make externalizing the buttons as needed in this application any easier..?
This is what I ended up doing. I got some good advice from another XDA'er who suggested I just pop the bubble button off the ribbon and solder to the contacts directly. In reality the bubble buttons are on a laminated sticker that I could just peel back. Then I soldered to the pads and pushed the cables out through where the rubber for the power button used to be. So far things seem to be working well, I'm a little weary of how this soldering will survive the swings in temperature being left in the car, but I guess there's only one way to find out. Observe:
Click to expand...
Click to collapse
Thats very nicely done. I want to do power and volume for my setup. Did the wire size you use work well or would you recommend smaller? otherwise i will need a separate volume control solution for the system. what do you have your tablet connected to for your amp and speakers?
Thanks. I used a 22 gauge wire, the smaller the better I think, as long as it's not bare. As far as amp, I'm using an aftermarket CD deck with a 3.5mm audio in. So I don't really plan on changing the volume on the tablet itself. I'll probably just keep it at 90% to avoid clipping and then adjust the gain with the CD deck. I haven't put it in my car yet though.
Steering Wheel Controls for Car PC
Has anyone tried the Joycon steering wheel control system with an android yet? It supports HID and no drivers are required for windows. It says that it cannot be programed from a linux or mac computer but just windows. Though once its programed it can be used with linux. Im thinking USB OTG plus this guy and you could control the tablet right from the steering wheel.
The solder will last fine on that job. The only thing I would be concerned about is getting false "presses" from the one lead that's soldered to the middle touching the outside ring. Perhaps just place a piece of electrical tape under it. Your other option might be to go straight from the connector the the flex plugs into. Just use a multimeter to test which pins you need to tap.
Thank you so much.
dmexs said:
How would that make externalizing the buttons as needed in this application any easier..?
This is what I ended up doing. I got some good advice from another XDA'er who suggested I just pop the bubble button off the ribbon and solder to the contacts directly. In reality the bubble buttons are on a laminated sticker that I could just peel back. Then I soldered to the pads and pushed the cables out through where the rubber for the power button used to be. So far things seem to be working well, I'm a little weary of how this soldering will survive the swings in temperature being left in the car, but I guess there's only one way to find out. Observe:
Click to expand...
Click to collapse
I just wanna thank the hell out of you. I have been searching and measuring that tiny little cable for about 2 hours now trying to find a connector and cable the right pitch/pins. Somehow the magical world of google brought me here. A site, despite my post numbers, I frequent very often. I'm installing the tablet in my car as well and I too needed a solution to the power button. Cant believe I didnt think to check here. You posted this just a few days ago. Crazy. Once again thank you. I should be able to pull this off no problem.
---------- Post added at 07:55 AM ---------- Previous post was at 07:49 AM ----------
Oh and by the way any issues with this so far? I dont imagine you have seeing as a switch on the to ends of the wire are doing exactly what the little foil button does. Just wanted to ask though before I commit to this in a couple of days.
I recommend if you are going to put it in a car, it needs some sort of quick release. If any stress is put on that cable, the contacts would either lift or the flex would rip pretty easily. I did my nook soldered straight to the main board and a quick release in the cable between the board and the button. I also did as much as I could to keep the cable from the back housing to board from moving by putting tape and locking the cable down when I put the back housing on.
The first picture shows the main board of the Nook. I just took off the old button and replaced it with my wiring. I used hot glue to keep it from wiggling.You can see the quick releases I used in the second picture. I just pulled them from a donor PC I had laying around.
Being a USB fan, I'd try to see if a custom USB device could do the job.
Just recently I made a USB volume control for Windows.
It works on my Nook Touch too.
Omyn said:
I recommend if you are going to put it in a car, it needs some sort of quick release. If any stress is put on that cable, the contacts would either lift or the flex would rip pretty easily. I did my nook soldered straight to the main board and a quick release in the cable between the board and the button. I also did as much as I could to keep the cable from the back housing to board from moving by putting tape and locking the cable down when I put the back housing on.
The first picture shows the main board of the Nook. I just took off the old button and replaced it with my wiring. I used hot glue to keep it from wiggling.You can see the quick releases I used in the second picture. I just pulled them from a donor PC I had laying around.
Click to expand...
Click to collapse
Exactly. I'm planning on using a male and female molex connector I found at radioshack. Currently I'm trying to figure out some intricacies involving Google Music and external storage but soon I'll have more pictures up here.
dmexs said:
Exactly. I'm planning on using a male and female molex connector I found at radioshack. Currently I'm trying to figure out some intricacies involving Google Music and external storage but soon I'll have more pictures up here.
Click to expand...
Click to collapse
keep us posted on the google music + external storage because i will be doing that soon aswell.
Have you tried connecting a faux USB HID device (like the Arduino Leonardo) and sending arbitrary keycodes while it's "off" to see whether any might be capable of waking it up? I don't know whether that could power it up from a "cold off" state, but I'm 99% sure you could wake it up from "screen off, asleep" that way.
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
bitbang3r said:
Have you tried connecting a faux USB HID device (like the Arduino Leonardo) and sending arbitrary keycodes while it's "off" to see whether any might be capable of waking it up? I don't know whether that could power it up from a "cold off" state, but I'm 99% sure you could wake it up from "screen off, asleep" that way.
Sent from my SAMSUNG-SGH-I747 using Tapatalk 2
Click to expand...
Click to collapse
I haven't tried this. I've just been using my externalized power button to wake the device from both warm and cold off states. I have a CNX-2140 power supply from my old car PC setup that has an ACPI pulse. I use this to wake the device from a warm sleep.
Thanks you XDA for being here. Just solved half of the problem my friend was having for his tablet . Mounting it in a 2006 Mustang. Now, Gotta see if he can use the POGO for charging and a USB OTG for the external camera
its help!! thanks!
What do you terminate the raw wire ends to now? I'd by looking at mounting some kind of button inside the cab of my vehicle to turn it on/off. What kind of button would a person look for? Thanks
---------- Post added at 09:44 AM ---------- Previous post was at 09:39 AM ----------
dmexs said:
How would that make externalizing the buttons as needed in this application any easier..?
This is what I ended up doing. I got some good advice from another XDA'er who suggested I just pop the bubble button off the ribbon and solder to the contacts directly. In reality the bubble buttons are on a laminated sticker that I could just peel back. Then I soldered to the pads and pushed the cables out through where the rubber for the power button used to be. So far things seem to be working well, I'm a little weary of how this soldering will survive the swings in temperature being left in the car, but I guess there's only one way to find out. Observe:
Click to expand...
Click to collapse
What do you terminate the raw wire ends to now? I'd by looking at mounting some kind of button inside the cab of my vehicle to turn it on/off. What kind of button would a person look for? Thanks