Database Users

upgrading to new radio without fastboot?

my phone is an htc magic 32A, i am currently on old radio and spl and amon_ra recovery for sapphire.
my usb connection has been dead for a while now, but i can still charge my phone. i use terminal for most things and root explorer so no need for adb or fastboot as much. but anyways, is there a way to flash the new radio (6.35), spl, and recovery without fastboot?
what i know:
1. i can flash new radio & spl through update.zip files through recovery, i've done it before with old radio and spl many times fine.
2. i can flash new recovery using terminal with phone on, this is fine i do many times too.
however, this is the problem, correct me if i'm wrong, you have to flash all 3 at same time right? in recovery mode, i can only flash radio and spl no recovery, but in terminal i can only flash recovery, not the other two.
is there a way around this that i dont know about? is fastbooting the only way?
I tried flashing the new recovery first and then booting into it to flash radio and spl but that dont work hehe. i dont think i can flash new radio and spl first using the current recovery image since cursor said in his thread if you flash radio and spl, the phone will keep rebooting because of the wrong recovery. since i cannot fastboot, this will pretty much kill my phone since i wont be able to boot it up to flash proper recovery image.
-------------------EDIT
cursordroid is helping me with this problem. for those interested check out his how-to guide in the dev section as that's where he posted a reply to me. hopefully his solution works, will see tomorrow.

Hi,
I've read a bit and i would like to share my understanding with you. Correct me if i'm wrong:
- The SPL is the boot code that allow the usage of fastboot commands and is there to actually boot the rom stored on the phone. As long as you have a correct SPL, you should be able to push a recovery-RA image trough USB into memory and boot with this code.
- The recovery image on the phone is a specific partition that is trigerred when you use the volume down and poweron button. I've got the impression that the vol-down and poweron instructs the spl to use the recovery partition. I'm not sure of this
If you are able to flash the recovery image (the Hero one) via terminal then from the pc using the command : fastboot boot recovery-RA-saphire-v1.5.2h, you shoudl normally get access to sdcard and flash the update_radio.zip then update_spl.zip.
I'm not sure of one thing: Does updating radio and updating spl should happen at the same time ? Can we do this by flash first the radio, reboot, fastboot boot then flash the spl ? As there is a reboot in between, wHat happens if the radio is newer than the spl ? Do we still have access to the fastoot mode ?
About your statement: "if you flash radio and spl, the phone will keep rebooting because of the wrong recovery." --> Where have you seen this ?
Cedric

Thanks but I Know about fastbooting and do it often but The problem is I cannot use usb fastboot anymore. Theres something wrong with my devices usb port. Please read the thread title and my post once more. If i can use my usb then fast boot is easy, I wouldn't have made this thread haha.
About the last statement it can be found in cursordroids thread about upgrading the radio.

Is there a way to mount the phone while in Bootloader mode?

I just ran a task29 on my phone and before flashing my new ROM I want to change the splashscreen as its one from Chuckydroid ROM and task29 doesnt delete bootup screen or splash screens. So is there a way to mount while in USB. I know the PC is making some sort of mount since I'm able to flash a new ROM but I cant find where

splash screens flash in exactly the same way as roms and radios, via an nbh file and customruu, and yes you can flash all three from bootloader. no, you won't see anything mounted, you can't access the memory from bootloader.

help with cyanogen Rom upgrade from 5.0.7 to 6.0.0

I have a rooted mytouch original with cyanogen 5.0.7/android 2.1 and want to upgrade to cyanogen 6.0.0/android 2.2.
Can I just install the new rom, or are their prior steps to prepare for this.
Thanks
DAve

Check CM wiki.. all the info is there!

yes, I had already read through the cm wiki before posting. I just read through it a second time, though the specific question that I had asked was not addressed as far as I could tell. Don't want to flash a new rom without first knowing its the right step to take. So if someone doesn't mind answering the question...

Just do a nandroid backup. Then you flash the CM 6 over the old one, do a cache+dalvic wipe and start it up.... It should be ok.
If not, then just revert back with the knowledge that you have to do a complete wipe, meaning that you need to start from scratch.

I now have initiated flashing new rom, starting with backing up data and wiping cash. However, I am now unable to go into recovery mode, whereas the phone is stuck on the logo when attempting to do so. I had installed through rom manager clockworkmod 2.5.0.1, got the message it installed correctly.
Here are the methods I have used to go into recovery:
1. click on "reboot into recovery"
2. backup current rom
3. flash alternative recovery with RA Recovery v.1.7.OH downloaded by rom manager, and use rom manager to restart into recovery mode
4. turn phone off, try to press home and power button together, for the new RA and the new clock work mod programs.
will not go into recovery mode, gets stuck on the boot up logo. Phone otherwise works fine, on the older Cyanogen Rom..., just can't go into recovery mode which I need to do to upgrade.
My original recovery was RAv1.2.0G.img, but this was I assume replaced by the rom manager.
In case this is important, my other software versions I have been using the past year:
Hboot 1.33.2005 (sapp30000), Cpld 10, Radio 2.22.19.261
will not go into recovery mode, gets stuck on the boot up logo. Phone otherwise works fine, on the older Cyanogen Rom...
any suggestions?

You flashed wrong recovery version...
You need RA Recovery v.1.7.OG and not H as stated above.
If all ****s up, then use my guide (check my signature) to flash a custom recovery... just skip the steps about root since you already got that!
Remember, G and NOT H.

lost recovery
mumilover
I do actually have v.1.7.0G installed, not H (my bad).
it just will not go into recovery.
Please let me know where your guide is, but right now I have been unable to communicate with my device through my xp desktop, get the "device not found" error (I assume you are suggesting that). Not sure how this will help though, since I already seem to have the correct recovery image installed.
Any help you can offer would be appreciated.
Dave
mumilover said:
You flashed wrong recovery version...
You need RA Recovery v.1.7.OG and not H as stated above.
If all ****s up, then use my guide (check my signature) to flash a custom recovery... just skip the steps about root since you already got that!
Remember, G and NOT H.
Click to expand...
Click to collapse

Download my fastboot commander (CHECK MY SIGNATURE, magic version).
Restart into fastboot mode.
Download this recovery image:
http://rapidshare.com/files/387932919/recovery-RA-sapphire-v1.7.0G.img
Using the tool and your eng spl, you can just flash the recovery image on the phone.
Just use the first tab -> recovery button -> navigate to the above image -> click "flash recovery". Done.
Restart into recovery by home + power combo.
You could also try this command:
Code:
adb shell reboot recovery
to force it to boot into recovery from the system.

[Problem is fixed. Thanks for your help.
I used my mac bootcamp (could not get sdk to run on my desktop or mac), and could find my device through adb. Then I pushed a separate version of the RA 1.7.0 G (the one the came with rom manager did not work!) to my phone via flash command. Voila, I am now able to go into recovery mode. 6.0 is installed and running.
QUOTE=mumilover;10252460]Download my fastboot commander (CHECK MY SIGNATURE, magic version).
Restart into fastboot mode.
Download this recovery image:
http://rapidshare.com/files/387932919/recovery-RA-sapphire-v1.7.0G.img
Using the tool and your eng spl, you can just flash the recovery image on the phone.
Just use the first tab -> recovery button -> navigate to the above image -> click "flash recovery". Done.
Restart into recovery by home + power combo.
You could also try this command:
Code:
adb shell reboot recovery
to force it to boot into recovery from the system.[/QUOTE]

" x " appears on the screen

Malfunction " x " appears on the screen !! help me what is going on

Haha... you'll need more information than that if you want real help.
Based on the limited information though I suspect your phone is stuck in a bootloop. I'd hook it up to the PC via USB and check the logcat. Probably something screwed up.. Maybe time to restore your latest backup.

Did you flash any ROM if so, did you clean your Dalvic+REgular Cache

If you don't have an Recovery:
- Connect your Micro SD on PC
- Download and insert on SD the stock ROM of your Nexus One
- Power ON your Nexus with Volume Down Pressed.
- Autmotically Restore Nexus (You should say Yes xD)
At this time, you decide if you want to be root and install other ROM

you better just list your setup info before doing anything
locked/unlocked bootloader
rooted/unrooted
which recovery are you using
what rom are you running stock/custom
what were you doing when this happened
a couple safe things you can do in meantime is to pull battery and reinsert and power on
if it goes back to X, pull battery and DO NOT power on. Hold down the pwr button and trackball at same time and see if you can get into recovery
the third is hold down trackball/vol-/power at same time while X is on screen and see if you can get to recovery that way
if you can't get to recovery you will need to fastboot new recovery, assuming you are unlocked
once you get into recovery do a nandroid if you are rooted
and copy it to pc as a secondary backup
it is possible you may need to try the passimg method in wiki
http://forum.xda-developers.com/wiki/Nexus_One/Guides_&_Tutorials#Unroot_.2F_Restore_your_Nexus
also to do fastboot commands you need usb debugging selected on phone--hope it is

Hello, i have a similar problem with my n1
the phone starts and just shows the nexus X - (waited for 15 min. nothing happend)
i can go to the bootloader / fastboot menu with PWR + (Vol-) but i can not go to the recovery mode. -> the phone reboots and get stuck at the X
the phone is rooted
blackrose / hboot 7.35.5017
radio 5.12.00.08
recovery was ext4
i had a german ics miui rom installed and tryed to install the latest ics miui us rom after it didn't booted the miui us rom i turned the phone off and tryed a few hours later to turn it on to reflash the german ics miui rom.
1.)
i tryed to install a new recovery image ->
recovery-clockwork-5.0.2.0-passion &
recovery-RA-passion-v2.2.1
(still get stuck at the X if i try to go to recovery mode)
2.)
i tryed this one with the passimg.zip but nothing happens if i put in the sd card :/
(with nothing i mean the green text show that the sd card is checking for PASSDIAG.zip and PASSIMG.zip but dosn't found it)
i also tryed:
3.)
erased boot
flash boot from passimg.zip (PASSIMG_Passion_Google_WWE_2.18.1700.1_FRG83_release_signed)
4.)
erased cache
erased userdata
started again with 1.)
5.)
got frustrated and erased system -.-
any ideas?

study it ,thank you
study it ,thank you

Hmm, sorry if its obvious but i have no idea what it could be or what i have to search to find the solution. Would be nice if you could give me a hint. Of course im not asking for a step by step solution. Thank you.
Send from my awesome SE K800i

not sure why you are flashing boot images
do you have a nandroid--copy your sdcard with the nandroid to pc--all of sdcard
are you flashing thru fastboot in command window
did you read my post above on getting to the fastboot screen--can you do that--the one with the 3 androids
pwr/vol-/trackball same time, may take 20-30 seconds
if you can get there, put your recovery image in your fastboot folder on pc, normally tools--assuming you have sdk installed, your phone must have usb debugging checked--I hope
open a command window and change directory to the tools folder or wherever the fastboot.exe file is. Something like:
cd/
cd/ android/android-sdk-windows/tools for me
then on same line type
fastboot devices (it should show your phone H#)
fastboot erase system
fastboot flash recovery recovery.img (or the exact name of the recovery image, checked by right clicking on the img file in your tools folder and looking under properties)
I would use amonra you listed above and check the md5 if possible
hopefully the recovery will flash
if not you can go to the wiki link i posted above and try passimg metthod from there, use correct one. don't add the .zip. Windows will had it automatically.
a side note, DON"T flash different roms without wiping all including System 3 times before flashing--prevents a lot of problems

rugmankc said:
a side note, DON"T flash different roms without wiping all including System 3 times before flashing--prevents a lot of problems
Click to expand...
Click to collapse
thank you very much
i already tryed everything else what you wrote but i didn't wiped 3 times... after erasing recovery partition 3 times i was able to flash a new recovery and it started.
Thanks a lot!

Glad that you got it

Request: Rehost of official ZTE Open C Flashing tool: Android version

Hi all,
I've been tracking this thing down all day to absolutely no avail. The main reason I'm after it is I've heard it changes the partition layout to enable a larger /data partition (Essentially turns the phone into a KIS 3).
The download links Comebuy are all completely down it seems, I've even tried using Wayback Machine but that's not coming up with much good either.
Does ANYONE have these tools - as I said, the one for flashing Android to the phone?
Thanks a lot everyone!

Hi.
I have the Open C upgrade tool zip. Is that what you need?

I've uploaded all Open C / Kis 3 Windows flash tool firmwares here. https://drive.google.com/folderview?id=0B9Xj0WNW4yX4b2tOXzFjN1RDRmc&usp=sharing#list
Also see Stock ROMs thread over at MoDaCo for regular firmware updates. http://www.modaco.com/forums/topic/373101-zte-kis-3-zte-open-c-stock-roms/

KonstaT said:
I've uploaded all Open C / Kis 3 Windows flash tool firmwares here. https://drive.google.com/folderview?id=0B9Xj0WNW4yX4b2tOXzFjN1RDRmc&usp=sharing#list
Also see Stock ROMs thread over at MoDaCo for regular firmware updates. http://www.modaco.com/forums/topic/373101-zte-kis-3-zte-open-c-stock-roms/
Click to expand...
Click to collapse
Will these work even if the device won't boot? I can't enable debug mode if I can't get past boot screen.

johnnynmonic said:
Will these work even if the device won't boot? I can't enable debug mode if I can't get past boot screen.
Click to expand...
Click to collapse
Why doesn't the device boot? What happened?
If you can boot to recovery (volume up + power) you can flash a firmware package. If you have Firefox OS bootloader you can boot directly to bootloader with volume down + power key combination and use fastboot to flash/boot recovery image first. I doubt Windows flasher will recognize your device.

KonstaT said:
Why doesn't the device boot? What happened?
If you can boot to recovery (volume up + power) you can flash a firmware package. If you have Firefox OS bootloader you can boot directly to bootloader with volume down + power key combination and use fastboot to flash/boot recovery image first. I doubt Windows flasher will recognize your device.
Click to expand...
Click to collapse
I don't know what happened, it belongs to my friend's daughter. She said she ran it down to 0% battery, then it never would boot up again. It SOMETIMES will boot as far as a welcome screen to set up language, but then says settings failed to start, exchange failed to start. I can't seem to get it into fastboot, but I can get it into recovery. Have tried flashing from sd, and via adb. Any image always fails. Have tried to load stock .zip images and even twmp and cwm, everything fails with either improper signature or footer. So not the end of the world, it's not even my phone, but I'm a chronic fiddler/tinkerer, and the fact that I can't make it work is maddening . Thanks for any tips.

johnnynmonic said:
I don't know what happened, it belongs to my friend's daughter. She said she ran it down to 0% battery, then it never would boot up again. It SOMETIMES will boot as far as a welcome screen to set up language, but then says settings failed to start, exchange failed to start. I can't seem to get it into fastboot, but I can get it into recovery. Have tried flashing from sd, and via adb. Any image always fails. Have tried to load stock .zip images and even twmp and cwm, everything fails with either improper signature or footer. So not the end of the world, it's not even my phone, but I'm a chronic fiddler/tinkerer, and the fact that I can't make it work is maddening . Thanks for any tips.
Click to expand...
Click to collapse
I assume it was running Firefox OS? On Firefox OS bootloader it just hangs on Firefox splash screen when you've booted to bootlader. Do you have proper fastboot drivers installed? ZTE uses generic Google mode for fastboot (18d1:d00d - e.g. USB driver from Android SDK works I've been told).
Stock recovery only allows you to flash matching stock firmware (and packages that are signed with ZTE's private keys). If you can get to bootloader you can flash/boot any recovery (stock or custom) and use it to flash firmware.

KonstaT said:
I assume it was running Firefox OS? On Firefox OS bootloader it just hangs on Firefox splash screen when you've booted to bootlader. Do you have proper fastboot drivers installed? ZTE uses generic Google mode for fastboot (18d1:d00d - e.g. USB driver from Android SDK works I've been told).
Stock recovery only allows you to flash matching stock firmware (and packages that are signed with ZTE's private keys). If you can get to bootloader you can flash/boot any recovery (stock or custom) and use it to flash firmware.
Click to expand...
Click to collapse
Thank you for taking the time to reply. I got it to get to the language selection (where it hangs if I can get it to boot that far). I plug it into the USB, and on the phone select connect to pc via software - then adb was able to detect it as a device. From there did: adb reboot bootloader, and once there was able to use fastboot to install cwm. From CWM was able to flash the EU_FFOS-Android kitkat rom. Works fine now. I see you've spent actually quite a bit of time making different roms and tutorials for theses ZTE phone in various forums. Thanks for sharing your knowledge with the community.
edit: I don't think it had FFOS. vol down+power never seemed to do anything (just perpetual bootsplash). Recovery failed to flash even stock roms (I'm in Thailand, downloaded the stock rom you linked to in another forum, also the stock UK rom. Always returned an error about the footer).